RFSAI-62B-SL, RFSAI-61B-SL, RFSAI-11B-SL
Canja naúrar tare da shigarwa don maɓallin waje
Halaye
- Ana amfani da ɓangaren sauyawa tare da fitarwa ɗaya/biyu don sarrafa kayan aiki da fitilu. Ana iya amfani da maɓalli/maɓallan da aka haɗa da wayoyi don sarrafawa.
- Ana iya haɗa su tare da Masu Ganowa, Masu Sarrafa ko Abubuwan Tsarin Sarrafa INELS RF.
- Sigar BOX tana kashe shigarwa kai tsaye a cikin akwatin shigarwa, rufi ko murfin na'urar da aka sarrafa. Sauƙaƙan shigarwa godiya ga tashoshi mara kyau.
- Yana ba da damar haɗin abubuwan da aka canza tare da jimlar jimlar 8 A (2000 W).
- Ayyuka: don RFSAI 61B-SL da RFSAI 62B-SL - maɓallin turawa, relay mai motsi da ayyukan lokaci na jinkirta farawa ko dawowa tare da saita lokaci 2 s-60 min. Ana iya sanya kowane aiki ga kowane fitarwar fitarwa. Don RFSAI-11B-SL, maɓallin yana da aikin fi xed - ON / KASHE.
- Ana sanya maɓallin waje kamar yadda mara waya.
- Kowace fitowar za a iya sarrafa ta har zuwa tashoshi 12/12 (tashar 1 tana wakiltar maɓalli ɗaya akan mai sarrafawa). Har zuwa tashoshi 25 don RFSAI-61B-SL da RFSAI-11B-SL.
- Maɓallin shirye-shirye akan ɓangaren kuma yana aiki azaman sarrafa fitarwa na hannu.
- Yiwuwar saita žwažwalwar ajiyar yanayin fitarwa idan an gaza da dawo da wuta na gaba.
- Ana iya saita abubuwan mai maimaitawa don abubuwan haɗin ta hanyar na'urar sabis na RFAF / USB, PC, aikace-aikace.
- Kewayi har zuwa m 200 (waje), idan akwai rashin isasshiyar sigina tsakanin mai sarrafawa da na'urar, yi amfani da mai maimaita siginar RFRP-20 ko sashi tare da ka'idar RFIO2 mai goyan bayan wannan aikin.
- Sadarwa tare da ka'idojin RFIO2 na biyu.
- Abubuwan tuntuɓar na'urar relay na AgSnO2 suna ba da damar sauya ballasts haske.
Majalisa
hawa a cikin akwatin shigarwa /
(har ma a ƙarƙashin maɓalli / sauyawa)
Haɗin kai
Tashoshi marasa dunƙule
ELKO EP, sro | Palackého 493 | 769 01 Holešov, Všetuly | Jamhuriyar Czech | e-mail: elko@elkoep.com | Taimako: +420 778 427 366
Shigar da siginar rediyo ta hanyar kayan gini daban-daban
|
|
 |
|
|
|
|
60 - 90% |
80 - 95% |
20 - 60% |
0 - 10% |
80-90% |
|
ganuwar tubali |
Tsarin katako tare da allunan filasta |
karfafa kankare |
karfe partitions |
gilashin gama gari |
Nuni, kulawa da hannu
1. LED / PROG button
• LED koren V1 - alamar halin na'urar don fitarwa 1
• LED ja V2 - alamar halin na'urar don fitarwa 2.
Manunonin aikin ƙwaƙwalwa:
Kunnawa - LED yana ƙyalli x 3.
Kashe - LED yana haskakawa sau ɗaya na dogon lokaci.
• Ana yin sarrafawa ta hannu ta latsa maɓallin PROG don <1s.
Ana yin shirye-shirye ta latsa maɓallin PROG na 3-5s.
2. Toshe na ƙarshe - haɗi don maɓallin waje
3. Tushe mai ƙare - haɗa mai gudanarwa na tsaka tsaki
4. Tushewar tashar - haɗin haɗi tare da jimlar jimlar
8A na yanzu (misali V1=6A, V2=2A)
5. Tushe na ƙarshe don haɗa mai gudanarwa lokaci
A cikin shirye-shirye da yanayin aiki, LED a kan
bangaren yana haskakawa a lokaci guda duk lokacin da maɓallin ke
danna - wannan yana nuna umarnin mai shigowa.
* RFSAI-61B-SL: lambar fitarwa ɗaya, nunin matsayi ta jajayen LED
Yi amfani da kayan aiki mai dacewa (takarda, screwdriver) don turawa akan fil ɗin sarrafawa. Ana ɗaga batura kuma an saki maɓallin shirye-shirye.
Bayan cire maɓallin sarrafawa, maɓallin shirye-shirye yana samun dama
Ana sarrafa maɓallin shirye-shirye tare da kayan aiki na bakin ciki mai dacewa.
Daidaituwa
Ana iya haɗa na'urar tare da duk abubuwan haɗin tsarin, sarrafawa da na'urori
na iNELS RF Control da iNELS RF Control2.
Ana iya sanya mai ganowa hanyar sadarwa ta iNELS RF Control2 (RFIO2).
Zaɓin tashoshi
Zaɓin tashoshi (RFSAI-62B-SL) ana yin ta ta latsa maɓallan PROG na 1-3s.
RFSAI-61B-SL: latsa fiye da daƙiƙa 1.
Bayan sakin maɓallin, LED yana nuna alamar fitarwa: ja (1) ko
kore (2). Duk sauran sigina ana nuna su ta daidai launi na LED ga kowane
tashar.
Ayyuka da shirye-shirye tare da masu watsa RF
Maɓallin aiki
Za a rufe lambar fitarwa ta latsa maɓallin kuma buɗe ta sakewa
maballin.
Domin aiwatar da daidaitattun umarni guda ɗaya (latsa = rufewa / sakewa da
button = budewa), jinkirin lokaci tsakanin waɗannan umarni dole ne ya zama minti na .
1s (latsa - jinkirta 1s - saki).
Shirye-shirye
Danna maɓallin shirye-shirye
akan mai karɓar RFSAI-62B na 3-5 s
(RFSAI-61B-SL: latsa don fiye da
1 s) zai kunna mai karɓar RFSAI-62B
cikin yanayin shirye-shirye. LED da
walƙiya a cikin tazarar 1s.
Zaɓi kuma danna maɓalli ɗaya
a kan mara waya ta sauya, zuwa wannan maballin
za a sanya aikin
Maɓalli.
Danna maɓallin shirye-shirye
akan mai karɓa RFSAI-62B ya fi guntu
sa'an nan 1 seconds zai fi nish programming
yanayin. LED
yana haskakawa bisa ga saiti
aikin ƙwaƙwalwar ajiya.
Kunna aiki
Bayanin kunnawa
Za a rufe lambar fitarwa ta latsa maɓallin.
Shirye-shirye
Danna maɓallin shirye-shirye a kunne
mai karɓar RFSAI-62B don 3-5 s (RFSAI-
11B-SL: latsa fiye da 1s)
zai kunna mai karɓar RFSAI-62B
cikin yanayin shirye-shirye. LED da
walƙiya a cikin tazarar 1s.
Latsa biyu na zaɓinku
maballin akan mai watsa RF
ba da damar kunna aikin
(dole ne ya zama raguwa na 1s tsakanin
matsi guda ɗaya).
Danna maɓallin shirye-shirye
akan mai karɓa RFSAI-62B ya fi guntu
sai dakika 1 zai gama programming
yanayin. LED
yana haskakawa bisa ga saiti
aikin ƙwaƙwalwar ajiya.
Kashe aiki
Za a buɗe lambar fitarwa ta latsa maɓallin.
Shirye-shirye
Danna maɓallin shirye-shirye a kunne
mai karɓar RFSAI-62B don 3-5 s (RFSAI-
61B-SL: latsa don fiye da 1
s) zai kunna mai karɓar RFSAI-62B
cikin yanayin shirye-shirye. LED da
walƙiya a cikin tazarar 1s.
Latsa uku na zaɓinku
maballin akan mai watsa RF
yana ba da aikin kashewa
(dole ne ya zama raguwa na 1s tsakanin
matsi guda ɗaya).
Danna maɓallin shirye-shirye
akan mai karɓa RFSAI-62B ya fi guntu
sa'an nan 1 seconds zai fi nish programming
yanayin. LED
yana haskakawa bisa ga saiti
aikin ƙwaƙwalwar ajiya.
Relay aikin motsa jiki
Bayanin isar da saƙon motsa jiki
Za a canza lambar fitarwa zuwa matsayi na gaba ta kowane latsa maɓallin. Idan an rufe lambar sadarwa, za a buɗe kuma akasin haka.
Shirye-shirye
Danna maɓallin shirye-shirye
akan mai karɓar RFSAI-62B na 3-5 s
(RFSAI-61B-SL: latsa don fiye da s1) zai kunna RFSAI-62B mai karɓa zuwa yanayin shirye-shirye. LED yana walƙiya a cikin tazarar 1s.
Latsa huɗu na zaɓinku
maɓalli akan mai watsa RF da aka sanya
Relay aikin motsa jiki
(dole ne ya zama raguwa na 1s tsakanin
matsi guda ɗaya).
Danna maɓallin shirye-shirye
akan mai karɓar RFSAI-62B ya gajarta sai daƙiƙa 1 zai gama shirye-shiryen
yanayin. LED ɗin yana haskakawa bisa ga saiti
aikin ƙwaƙwalwar ajiya.
An jinkirta aiki
Bayanin jinkirta kashewa
Za a rufe lambar fitarwa ta latsa maɓallin kuma buɗe bayan tazarar lokacin da aka saita ya wuce.
Danna maɓallin shirye-shirye a kunne
mai karɓar RFSAI-62B don 3-5 s (RFSAI-
61B-SL: latsa don fiye da 1
s) zai kunna mai karɓar RFSAI-62B
cikin yanayin shirye-shirye. LED da
walƙiya a cikin tazarar 1s.
Assignment na jinkirta kashe
Ana yin aikin ta hanyar biyar
danna maɓallin da aka zaɓa
akan mai watsa RF (dole ne
raguwar 1s tsakanin matsi guda ɗaya).
Danna maɓallin shirye-shirye
ya fi tsayi sannan 5 seconds, zai
kunna actuator cikin lokaci
yanayin. LED fl ashs 2x a kowane
Tazarar 1s. Bayan fitar da
maballin, jinkirin dawowa
lokaci ya fara kirgawa.
Bayan lokacin da ake so yana da
ya wuce (kewayon 2s… 60min),
yanayin lokacin yana ƙarewa
danna maballin akan
Mai watsa RF, wanda aikin dawowar jinkiri yake
sanyawa. Wannan yana adana tazarar lokacin da aka saita a cikin mai kunnawa
ƙwaƙwalwar ajiya.
Danna maɓallin shirye-shirye
akan mai karɓa RFSAI-62B ya fi guntu
sai dakika 1 zai gama programming
yanayin. Fitilar LED
sama bisa ga aikin ƙwaƙwalwar ajiya da aka saita.
An jinkirta aiki
Bayanin jinkiri akan
Za a buɗe lambar fitarwa ta latsa maɓallin kuma rufe bayan saiti
tazarar lokaci ya wuce.
Danna maɓallin shirye-shirye a kunne
mai karɓar RFSAI-62B don 3-5 s (RFSAI-
61B-SL: latsa don fiye da haka
1s) zai kunna mai karɓar RFSAI-
62B cikin yanayin shirye-shirye.
LED yana walƙiya a cikin tazarar 1s.
Assignment na jinkiri a kan
Ana yin aikin ta shida
danna maɓallin da aka zaɓa
akan mai watsa RF (dole ne
raguwar 1s tsakanin matsi guda ɗaya).
Danna maɓallin shirye-shirye
ya fi tsayi sannan 5 seconds, zai
kunna actuator cikin lokaci
yanayin. LED fl ashs 2x a kowane
Tazarar 1s. Bayan fitar da
maballin, jinkirin dawowa
lokaci ya fara kirgawa.
Bayan lokacin da ake so yana da
ya wuce (kewayon 2s… 60min),
yanayin lokacin yana ƙarewa
danna maballin akan
Mai watsa RF, wanda zuwansa
jinkirin dawowa aikin shine
sanyawa. Wannan yana adana saitin
Tazarar lokaci a cikin ƙwaƙwalwar actuator.
Danna maɓallin shirye-shirye
akan mai karɓa RFSAI-62B ya fi guntu
sa'an nan 1 seconds zai fi nish programming
yanayin. Fitilar LED
sama bisa ga aikin ƙwaƙwalwar ajiya da aka saita.
Shirye-shirye tare da sassan sarrafa RF
Ana amfani da adiresoshin da aka jera a gefen gaba na mai kunnawa don tsarawa
da sarrafa mai kunnawa da kowane tashoshi na RF ta ƙungiyoyin sarrafawa.
Share actuator
Ta danna maɓallin shirye-shirye a kan actuator na 8 seconds
(RFSAI-61B-SL: latsa don 5 seconds), shafewa ɗaya
kunnawa. LED yana walƙiya 4x a kowane tazara 1s.
Danna maɓallin da ake buƙata akan mai watsawa yana share shi daga
ƙwaƙwalwar mai kunnawa.
Don tabbatar da gogewa, LED ɗin zai tabbatar da dogon ash kuma
bangaren ya koma yanayin aiki. Ƙwaƙwalwar ajiya
ba a nuna matsayi ba.
Sharewa baya shafar aikin ƙwaƙwalwar ajiya da aka saita.
Ta danna maɓallin shirye-shirye a kan actuator na 11 seconds
(RFSAI-61B-SL: latsa don fiye da daƙiƙa 8), shafewa yana faruwa
na duk memory na actuator. LED yana walƙiya 4x a kowane tazara 1s.
Mai kunnawa yana shiga yanayin shirye-shirye, toka fl na LED
a cikin tazara na 0.5s (max. 4 min.).
Kuna iya komawa yanayin aiki ta latsa maɓallin Prog
kasa da 1s. LED ɗin yana haskakawa bisa ga ƙwaƙwalwar ajiyar da aka saita
aiki kuma bangaren ya koma yanayin aiki.
Sharewa baya shafar aikin ƙwaƙwalwar ajiya da aka saita.
Zaɓi aikin ƙwaƙwalwar ajiya
Danna maɓallin shirye-shirye akan mai karɓar RFSAI-62B na 3-5 seconds
(RFSAI-61B-SL: latsa don 1 seconds) zai kunna mai karɓar RFSAI-
62B cikin yanayin shirye-shirye. LED yana haskakawa a cikin tazarar 1s.
Danna maɓallin shirye-shirye akan mai karɓar RFSAI-62B don
kasa da daƙiƙa 1 zai ƙare yanayin shirye-shiryen, wannan zai juya baya
aikin ƙwaƙwalwar ajiya. LED yana haskakawa bisa ga
aikin žwažwalwar ajiya da aka saita na yanzu. Saitin aikin žwažwalwar ajiya shine
ceto.
Duk sauran canje-canje ana yin su ta hanya ɗaya.
- Aikin ƙwaƙwalwa akan:
– Domin ayyuka 1-4, ana amfani da waɗannan don adana yanayi na ƙarshe na fitarwar relay kafin samar da voltage sauke, ana yin rikodin canjin yanayin fitarwa zuwa ƙwaƙwalwar ajiya 15 seconds bayan canjin. - Don ayyuka 5-6, yanayin da aka yi niyya na relay yana shiga cikin ƙwaƙwalwar ajiya nan da nan bayan jinkiri, bayan sake haɗa wutar lantarki, an saita relay zuwa yanayin da aka yi niyya.
- A kashe aikin ƙwaƙwalwa:
Lokacin da aka sake haɗa wutar lantarki, gudun ba da sanda ya kasance a kashe.
Maɓallin waje RFSAI-62B-SL an tsara shi kamar yadda ake yi don mara waya.
RFSAI-11B-SL ba a tsara shi ba, yana da tsayayyen aiki.
Siffofin fasaha
| Ƙarar voltage: | 230 V AC |
| Ƙarar voltage mita: | 50-60 Hz |
| Shigar da ke bayyane: |
7 VA / cos φ = 0.1
|
| Rashin wutar lantarki: | 0.7 W |
| Ƙarar voltage haƙuri: | =+10%; -15% |
| Fitowa | |
| Adadin abokan hulɗa: |
1x canzawa 2x canzawa
|
| Ƙididdigar halin yanzu: | 8 A / AC1 |
| Ƙarfin juyawa: | 2000 VA / AC1 |
| Kololuwar halin yanzu: | 10 A / <3 s |
| Sauyawa voltage: | 250V AC1 |
| Rayuwar sabis na injina: | 1×107 |
| Rayuwar sabis na lantarki (AC1): | 1×105 |
| Sarrafa | |
| Mara waya: |
25-tashoshi - 2 x 12-tashoshi
|
| Adadin ayyuka: | 1,6,6 |
| Ka'idar sadarwa: | RFIO2 |
| Mitar: |
866-922 MHz (don ƙarin bayani duba shafi na 74)/866-922 MHz (см. стр. 74)
|
| Maimaita aikin: | iya |
| Ikon sarrafawa: |
maɓallin PROG (ON / KASHE) /
|
| Maɓallin waje / sauyawa: Range: | iya |
| Sauran bayanai |
a cikin sarari har zuwa 200 m
|
|
Yanayin aiki:
|
|
| Matsayin aiki: | -15 az + 50 ° C |
| Matsayin aiki: | kowane |
| hawa: |
kyauta a wayoyi masu guba
|
| Kariya: | IP40 |
| Ƙarfafawatage category: | III. |
| Matsayin gurɓatawa: | 2 |
| Haɗin kai: |
dunƙule tashoshi
|
| Mai haɗawa: |
0.2-1.5 mm2 m / fl exible
|
| Girma: |
43 x 44 x 22 mm
|
| Nauyi: | 31g45 ku |
| Matsayi masu alaƙa: |
EN 60730, EN 63044, EN 300 220, EN 301 489
|
* Shigar da maɓallin sarrafawa yana a kan samar da voltage m.
Hankali:
Lokacin da kuka shigar da tsarin INELS RF Control, dole ne ku kiyaye mafi ƙarancin tazara 1 cm tsakanin kowace raka'a.
Tsakanin umarni ɗaya dole ya kasance tazara na aƙalla 1s.
Gargadi
An tsara littafin koyarwa don hawa da kuma mai amfani da na'urar. Koyaushe wani bangare ne na shiryawa. Ana iya aiwatar da shigarwa da haɗin kai kawai ta mutumin da ke da isassun ƙwararrun ƙwararru bayan fahimtar wannan jagorar koyarwa da ayyukan na'urar, da kuma kiyaye duk ƙa'idodi masu inganci. Babu matsala
Ayyukan na'urar kuma ya dogara da sufuri, adanawa da sarrafawa. Idan kun lura da kowace alamar lalacewa, nakasawa, rashin aiki ko ɓarna, kar a shigar da wannan na'urar kuma mayar da ita ga mai siyar ta. Wajibi ne a kula da wannan samfurin da sassansa azaman sharar lantarki bayan an ƙare rayuwarsa. Kafin fara shigarwa, tabbatar
cewa duk wayoyi, sassan da aka haɗa ko tashoshi ba su da kuzari. Yayin hawa da hidima kiyaye ƙa'idodin aminci, ƙa'idodi, umarni da ƙwararru, da dokokin fitarwa don aiki tare da na'urorin lantarki. Kar a taɓa sassan na'urar da ke da kuzari - barazanar rayuwa. Saboda watsa siginar RF, lura da daidai wurin abubuwan RF a cikin ginin da ake yin shigarwa. Ikon RF an tsara shi ne kawai don hawa a ciki. Ba a keɓance na'urori don shigarwa cikin waje da sarari masu ɗanɗano ba. Ba dole ba ne a shigar da shi cikin allunan karfe da kuma cikin allunan filastik tare da ƙofar ƙarfe - watsa siginar RF ba zai yiwu ba. Ba a ba da shawarar Sarrafa RF don abubuwan jan hankali da sauransu – siginar mitar rediyo na iya kiyaye shi ta hanyar toshewa, tsoma baki, baturi na transceiver zai iya samun fl a da sauransu kuma ta haka yana kashe ikon nesa.
ELKO EP ya bayyana cewa nau'in kayan aiki na RFSAI-xxB-SL ya dace da Dokokin 2014/53/EU, 2011/65/EU, 2015/863/EU da 2014/35/EU. Cikakkun EU
Sanarwa na Daidaitawa yana a:
https://www.elkoep.com/switching-units-with-inputs-for-external-buttons—-rfsai-11b-sl
https://www.elkoep.com/switching-units-with-inputs-for-external-buttons—-rfsai-61b-sl
https://www.elkoep.com/switching-units-with-inputs-for-external-buttons—rfsai-62b-sl
ELKO EP, sro, Palackého 493, 769 01 Holešov, Všetuly, Jamhuriyar Czech
Tel.: +420 573 514 211, e-mail: elko@elkoep.com, www.elkoep.com
Takardu / Albarkatu
 |
Elko EP RFSAI-62B-SL Canja Unit tare da Input Don Maɓallin waje [pdf] Jagoran Jagora RFSAI-62B-SL Canja Unit tare da Input Don Maɓallin waje, RFSAI-62B-SL |
