Grafik Tech Un-Lock Nut String Slotted

Mahsulot haqida ma'lumot

Texnik xususiyatlari:

• KOD:
  • 6517 FR original №2
  • 6518 FR original #3/#4
  • 6519 FR Maxsus
  • 6520 IBANEZ uslubi
• Mahsulot o'lchamlari:
  • Uzunlik: 43.00 mm / 1.693 dyuym
  • Qalinligi: 15.40 mm / 0.606 dyuym
  • Balandligi: 7.50 mm / 0.295 dyuym
    (Turli modellar uchun qo'shimcha o'lchamlar mavjud)
• E dan E gacha:
  Har bir model uchun o'lchovlar mavjud
• Radius:
  254 mm / 10 dyuym (ko'pgina modellar uchun)

Mahsulotdan foydalanish bo'yicha ko'rsatmalar

Yong'oqni qulfdan chiqarish bo'yicha qo'llanma:

1. 1-QADAM: Follow instructions for low E and high E gap measurements.
2. 2-QADAM: Perform the specified actions for step 2.
3. 3-QADAM: Continue with the instructions for step 3.
4. 4-QADAM: Adjust the gap for low E and high E as per the provided values.
5. 5-QADAM: Proceed with step 5 of the installation process.
6. 6-QADAM: Finalize the installation process following step 6.
   Eslatma: For additional assistance and compatibility, use the Total Control & Precision Locking Machine Heads from Graph Tech in conjunction with the Un-Lock Nut.

Bog'lanish uchun ma'lumot:

• Websayt: www.graphtech.com
• Elektron pochta orqali yordam: support@graphtech.com
• Qo'llab-quvvatlash tel: 604-940-5353 ichki 130
  To download additional product measurements and installation instructions, visit the Help Center link under the Support section on the websayt.

XUSUSIYATLARI

• Optimally ramped and angled string slot design (distributes the string tension over the entire string ramp), which allows us to triple the lubrication.
• Waaaaay easier string bends on the Ist to 5th string positions.
• Faster string changes.
• 80% reduced headstock weight.
• No more Allen keys for your nut.
• Improved string to headstock connection (You’ll feel this the first time you play).
• Straightforward upgrade, a final tweak on sanding to flush fit with the edge of the fingerboard, and a drop of white glue.
• The ability to tweak string heights, just like a regular nut.
• 10,12, and 16-inch radius available (more models on the way).
  AND, you can finally tweak and tune with your machine heads (locking machine heads recommended, but not mandatory)

  
  

QULFLANISH SOG'QINI O'RNATISH bo'yicha qo'llanma

• 1-QADAM
  Remove the strings. Score around every edge of the nut with an exacto knife to prevent lacquer from sticking to the nut or the neck and chipping away.

  

• 2-QADAM
  If the nut is not sitting in a slot, usually a light tap with a small block will set it free. If it is sitting in a slot, gently tap it out sideways using a hammer and a screwdriver.

  

• 3-QADAM
  When it is sticking out the side, pull it out in the same direction with a pair of pliers, like you would a tooth. Scrape or file the nut slot free from old glue and finish residue while making sure that the slot remains square.

  

• 4-QADAM
  See if your new Graph Tech nut fits into the slot without force. If it’s too thick, place a 400600-gritgrit sandpaper face up on a flat surface and sand down the sides of the nut until it fits in the slot snugly, but is easily removable.

  

• RetuReturn thernthe high and low E strings tto verify therify the correct height. Pushing down on the third note of the low E string should result in a .010″ gap between the string and the first fret; the high E string should be .006″

  

• 6-QADAM
  Once you’ve adjusted the thickness and the height, you just need to sand the ends of the nut so that they are flush with the neck. Use a pencil to mark the ends of the nut that are sticking out. Remove it from the neck and sand it to the marks.

  

KOMPANIYA HAQIDA

• Websayt:
  www.graphtech.com
• Qo'llab-quvvatlash:
  support@graphtech.com
• Qo'llab-quvvatlash tel:
  604-940-5353 ichki 130
  Graph Tech mahsulotlari uchun mahsulot oʻlchovlari va oʻrnatish yoʻriqnomalarini yuklab olish uchun bizning yuqori menyudagi “Yordam” boʻlimi ostidagi Yordam markazi havolasini toping. websayt.

TSS

Ushbu mahsulotni har qanday turdagi gitara bilan ishlata olamanmi?

The product is designed to be compatible with various guitar models, but please ensure compatibility with your specific guitar type before installation.

What do I do if I encounter issues during installation?

In case of any installation difficulties or issues, please reach out to our support team for assistance and guidance.

Hujjatlar / manbalar

Grafik Tech Un-Lock Nut String Slotted [pdf] Qo'llanma 6517, 6518, 6519, 6520, Qulfni ochish gayka torlari tirqishli, qulfdan chiqarish, gayka torlari tirqishli, tirqishli, tirqishli

Ma'lumotnomalar

• Foydalanuvchi uchun qo'llanma