Graph Tech навртка за откључавање са прорезом

Информације о производу

Спецификације:

• КОД:
  • 6517 ФР Оригинал #2
  • 6518 ФР Оригинал #3/#4
  • 6519 ФР Специјал
  • 6520 IBANEZ стил
• Димензије производа:
  • дужина: 43.00 мм / 1.693 ин
  • дебљина: 15.40 мм / 0.606 ин
  • Висина: 7.50 мм / 0.295 ин
    (Додатне димензије су дате за различите моделе)
• Од И до И:
  Мере су дате за сваки модел
• Радијус:
  254 мм / 10 инча (за већину модела)

Упутства за употребу производа

Водич за монтажу одвртања навртке:

1. 1. КОРАК: Follow instructions for low E and high E gap measurements.
2. 2. КОРАК: Perform the specified actions for step 2.
3. 3. КОРАК: Continue with the instructions for step 3.
4. 4. КОРАК: Adjust the gap for low E and high E as per the provided values.
5. 5. КОРАК: Proceed with step 5 of the installation process.
6. 6. КОРАК: Finalize the installation process following step 6.
   Напомена: For additional assistance and compatibility, use the Total Control & Precision Locking Machine Heads from Graph Tech in conjunction with the Un-Lock Nut.

Контакт информације:

• Webсајт: ввв.грапхтецх.цом
• Подршка путем е-поште: суппорт@грапхтецх.цом
• Телефонска подршка: 604-940-5353 ект КСНУМКС
  To download additional product measurements and installation instructions, visit the Help Center link under the Support section on the webсајту.

КАРАКТЕРИСТИКЕ

• Optimally ramped and angled string slot design (distributes the string tension over the entire string ramp), which allows us to triple the lubrication.
• Waaaaay easier string bends on the Ist to 5th string positions.
• Faster string changes.
• 80% reduced headstock weight.
• No more Allen keys for your nut.
• Improved string to headstock connection (You’ll feel this the first time you play).
• Straightforward upgrade, a final tweak on sanding to flush fit with the edge of the fingerboard, and a drop of white glue.
• The ability to tweak string heights, just like a regular nut.
• 10,12, and 16-inch radius available (more models on the way).
  AND, you can finally tweak and tune with your machine heads (locking machine heads recommended, but not mandatory)

  
  

ВОДИЧ ЗА УГРАЂИВАЊЕ ОТВОЈАЧАВАЈУЋЕ НАВРТКЕ

• КОРАК 1
  Remove the strings. Score around every edge of the nut with an exacto knife to prevent lacquer from sticking to the nut or the neck and chipping away.

  

• КОРАК 2
  If the nut is not sitting in a slot, usually a light tap with a small block will set it free. If it is sitting in a slot, gently tap it out sideways using a hammer and a screwdriver.

  

• КОРАК 3
  When it is sticking out the side, pull it out in the same direction with a pair of pliers, like you would a tooth. Scrape or file the nut slot free from old glue and finish residue while making sure that the slot remains square.

  

• КОРАК 4
  See if your new Graph Tech nut fits into the slot without force. If it’s too thick, place a 400600-gritgrit sandpaper face up on a flat surface and sand down the sides of the nut until it fits in the slot snugly, but is easily removable.

  

• RetuReturn thernthe high and low E strings tto verify therify the correct height. Pushing down on the third note of the low E string should result in a .010″ gap between the string and the first fret; the high E string should be .006″

  

• КОРАК 6
  Once you’ve adjusted the thickness and the height, you just need to sand the ends of the nut so that they are flush with the neck. Use a pencil to mark the ends of the nut that are sticking out. Remove it from the neck and sand it to the marks.

  

О КОМПАНИЈИ

• Webсајт:
  ввв.грапхтецх.цом
• Подршка:
  суппорт@грапхтецх.цом
• Телефонска подршка:
  604-940-5353 ект КСНУМКС
  Да бисте преузели мере производа и упутства за инсталацију производа Graph Tech, пронађите везу Центар за помоћ у одељку Подршка у горњем менију на нашем webсајту.

ФАК

Могу ли користити овај производ са било којом врстом гитаре?

The product is designed to be compatible with various guitar models, but please ensure compatibility with your specific guitar type before installation.

What do I do if I encounter issues during installation?

In case of any installation difficulties or issues, please reach out to our support team for assistance and guidance.

Документи / Ресурси

Graph Tech навртка за откључавање са прорезом [пдф] Упутство за употребу 6517, 6518, 6519, 6520, Навртка за откључавање са прорезом, Откључавање, Навртка са прорезом, Навртка са прорезом, Прорез

Референце

• Упутство за употребу