Graph Tech Un-Lock Nut String Slotted

Informazzjoni dwar il-Prodott

Speċifikazzjonijiet:

• KODIĊI:
  • 6517 FR Oriġinali #2
  • 6518 FR Oriġinali #3/#4
  • 6519 FR Speċjali
  • 6520 Stil IBANEZ
• Dimensjonijiet tal-Prodott:
  • Tul: 43.00 mm / 1.693 pulzieri
  • Ħxuna: 15.40 mm / 0.606 pulzieri
  • Għoli: 7.50 mm / 0.295 pulzieri
    (Dimensjonijiet addizzjonali pprovduti għal mudelli differenti)
• MINN E GĦAL E:
  Kejl ipprovdut għal kull mudell
• Raġġ:
  254 mm / 10 pulzieri (għal ħafna mudelli)

Istruzzjonijiet għall-Użu tal-Prodott

Gwida għall-Installazzjoni tal-Un-Lock Nut:

1. PASS 1: Follow instructions for low E and high E gap measurements.
2. PASS 2: Perform the specified actions for step 2.
3. PASS 3: Continue with the instructions for step 3.
4. PASS 4: Adjust the gap for low E and high E as per the provided values.
5. PASS 5: Proceed with step 5 of the installation process.
6. PASS 6: Finalize the installation process following step 6.
   Nota: For additional assistance and compatibility, use the Total Control & Precision Locking Machine Heads from Graph Tech in conjunction with the Un-Lock Nut.

Informazzjoni ta' Kuntatt:

• Websit: www.graphtech.com
• Appoġġ bl-Email: support@graphtech.com
• Appoġġ bit-Telefon: 604-940-5353 130 ext
  To download additional product measurements and installation instructions, visit the Help Center link under the Support section on the websit.

KARATTERISTIĊI

• Optimally ramped and angled string slot design (distributes the string tension over the entire string ramp), which allows us to triple the lubrication.
• Waaaaay easier string bends on the Ist to 5th string positions.
• Faster string changes.
• 80% reduced headstock weight.
• No more Allen keys for your nut.
• Improved string to headstock connection (You’ll feel this the first time you play).
• Straightforward upgrade, a final tweak on sanding to flush fit with the edge of the fingerboard, and a drop of white glue.
• The ability to tweak string heights, just like a regular nut.
• 10,12, and 16-inch radius available (more models on the way).
  AND, you can finally tweak and tune with your machine heads (locking machine heads recommended, but not mandatory)

  
  

GWIDA GĦALL-INSTALLAZZJONI TAL-UN-LOCK NUT

• PASS 1
  Remove the strings. Score around every edge of the nut with an exacto knife to prevent lacquer from sticking to the nut or the neck and chipping away.

  

• PASS 2
  If the nut is not sitting in a slot, usually a light tap with a small block will set it free. If it is sitting in a slot, gently tap it out sideways using a hammer and a screwdriver.

  

• PASS 3
  When it is sticking out the side, pull it out in the same direction with a pair of pliers, like you would a tooth. Scrape or file the nut slot free from old glue and finish residue while making sure that the slot remains square.

  

• PASS 4
  See if your new Graph Tech nut fits into the slot without force. If it’s too thick, place a 400600-gritgrit sandpaper face up on a flat surface and sand down the sides of the nut until it fits in the slot snugly, but is easily removable.

  

• RetuReturn thernthe high and low E strings tto verify therify the correct height. Pushing down on the third note of the low E string should result in a .010″ gap between the string and the first fret; the high E string should be .006″

  

• PASS 6
  Once you’ve adjusted the thickness and the height, you just need to sand the ends of the nut so that they are flush with the neck. Use a pencil to mark the ends of the nut that are sticking out. Remove it from the neck and sand it to the marks.

  

DWAR KUMPANIJA

• Websit:
  www.graphtech.com
• Appoġġ:
  support@graphtech.com
• Appoġġ bit-Telefon:
  604-940-5353 130 ext
  Biex tniżżel il-kejl tal-prodott u l-istruzzjonijiet tal-installazzjoni għall-prodotti ta' Graph Tech, sib il-link taċ-Ċentru tal-Għajnuna taħt it-taqsima Appoġġ fil-menù ta' fuq fuq is-sit tagħna. websit.

FAQ

Nista' nuża dan il-prodott ma' kwalunkwe tip ta' kitarra?

The product is designed to be compatible with various guitar models, but please ensure compatibility with your specific guitar type before installation.

What do I do if I encounter issues during installation?

In case of any installation difficulties or issues, please reach out to our support team for assistance and guidance.

Dokumenti / Riżorsi

Graph Tech Un-Lock Nut String Slotted [pdfManwal tal-Istruzzjonijiet 6517, 6518, 6519, 6520, Skorfina Un-Lock b'Spag, Un-Lock, Skorfina b'Spag, Skorfina b'Spag, Skorfina

Referenzi

• Manwal għall-Utent