Graph Tech atbloķēšanas uzgriežņu aukla ar spraugām

Informācija par produktu

Specifikācijas:

• KODS:
  • 6517 FR oriģināls #2
  • 6518 FR oriģināls #3/#4
  • 6519 FR Special
  • 6520 IBANEZ stila
• Produkta izmēri:
  • Garums: 43.00 mm / 1.693 collas
  • Biezums: 15.40 mm / 0.606 collas
  • Augstums: 7.50 mm / 0.295 collas
    (Dažādiem modeļiem ir norādīti papildu izmēri)
• NO E LĪDZ E:
  Katram modelim norādītie mērījumi
• Rādiuss:
  254 mm / 10 collas (vairumam modeļu)

Produkta lietošanas instrukcijas

Atbloķēšanas uzgriežņa uzstādīšanas rokasgrāmata:

1. 1. SOLIS: Follow instructions for low E and high E gap measurements.
2. 2. SOLIS: Perform the specified actions for step 2.
3. 3. SOLIS: Continue with the instructions for step 3.
4. 4. SOLIS: Adjust the gap for low E and high E as per the provided values.
5. 5. SOLIS: Proceed with step 5 of the installation process.
6. 6. SOLIS: Finalize the installation process following step 6.
   Piezīme: For additional assistance and compatibility, use the Total Control & Precision Locking Machine Heads from Graph Tech in conjunction with the Un-Lock Nut.

Kontaktinformācija:

• Webvietne: www.graphtech.com
• E-pasta atbalsts: support@graphtech.com
• Atbalsta tālrunis: 604-940-5353 ext 130
  To download additional product measurements and installation instructions, visit the Help Center link under the Support section on the webvietne.

ĪPAŠĪBAS

• Optimally ramped and angled string slot design (distributes the string tension over the entire string ramp), which allows us to triple the lubrication.
• Waaaaay easier string bends on the Ist to 5th string positions.
• Faster string changes.
• 80% reduced headstock weight.
• No more Allen keys for your nut.
• Improved string to headstock connection (You’ll feel this the first time you play).
• Straightforward upgrade, a final tweak on sanding to flush fit with the edge of the fingerboard, and a drop of white glue.
• The ability to tweak string heights, just like a regular nut.
• 10,12, and 16-inch radius available (more models on the way).
  AND, you can finally tweak and tune with your machine heads (locking machine heads recommended, but not mandatory)

  
  

ATVĒRŠANAS UZGRIEZŅA UZSTĀDĪŠANAS INSTRUKCIJA

• 1. SOLIS
  Remove the strings. Score around every edge of the nut with an exacto knife to prevent lacquer from sticking to the nut or the neck and chipping away.

  

• 2. SOLIS
  If the nut is not sitting in a slot, usually a light tap with a small block will set it free. If it is sitting in a slot, gently tap it out sideways using a hammer and a screwdriver.

  

• 3. SOLIS
  When it is sticking out the side, pull it out in the same direction with a pair of pliers, like you would a tooth. Scrape or file the nut slot free from old glue and finish residue while making sure that the slot remains square.

  

• 4. SOLIS
  See if your new Graph Tech nut fits into the slot without force. If it’s too thick, place a 400600-gritgrit sandpaper face up on a flat surface and sand down the sides of the nut until it fits in the slot snugly, but is easily removable.

  

• RetuReturn thernthe high and low E strings tto verify therify the correct height. Pushing down on the third note of the low E string should result in a .010″ gap between the string and the first fret; the high E string should be .006″

  

• 6. SOLIS
  Once you’ve adjusted the thickness and the height, you just need to sand the ends of the nut so that they are flush with the neck. Use a pencil to mark the ends of the nut that are sticking out. Remove it from the neck and sand it to the marks.

  

PAR UZŅĒMUMU

• Webvietne:
  www.graphtech.com
• Atbalsts:
  support@graphtech.com
• Atbalsta tālrunis:
  604-940-5353 ext 130
  Lai lejupielādētu Graph Tech produktu mērījumus un uzstādīšanas instrukcijas, atrodiet palīdzības centra saiti sadaļā Atbalsts mūsu vietnes augšējā izvēlnē. webvietne.

FAQ

Vai es varu izmantot šo produktu ar jebkura veida ģitāru?

The product is designed to be compatible with various guitar models, but please ensure compatibility with your specific guitar type before installation.

What do I do if I encounter issues during installation?

In case of any installation difficulties or issues, please reach out to our support team for assistance and guidance.

Dokumenti / Resursi

Graph Tech atbloķēšanas uzgriežņu aukla ar spraugām [pdfLietošanas instrukcija 6517, 6518, 6519, 6520, Atbloķējama uzgriežņu virkne ar rievu, Atbloķējama, Uzgriežņu virkne ar rievu, Aukla ar rievu, Rieva

Atsauces

• Lietotāja rokasgrāmata