그래프 테크 잠금 해제 너트 스트링 슬롯
제품 정보
명세서:
- 암호:
- 6517 FR 오리지널 #2
- 6518 FR 오리지널 #3/#4
- 6519 FR 스페셜
- 6520 IBANEZ 스타일
- 제품 크기:
- 길이: 43.00mm / 1.693인치
- 두께: 15.40mm / 0.606인치
- 키: 7.50mm / 0.295인치
(다른 모델에 대한 추가 치수 제공)
- E에서 E로:
각 모델에 대한 측정값 제공 - 반지름:
254mm / 10인치(대부분 모델)
제품 사용 지침
잠금 해제 너트 설치 가이드:
- 1단계: Follow instructions for low E and high E gap measurements.
- 2단계: Perform the specified actions for step 2.
- 3단계: Continue with the instructions for step 3.
- 4단계: Adjust the gap for low E and high E as per the provided values.
- 5단계: Proceed with step 5 of the installation process.
- 6단계: Finalize the installation process following step 6.
메모: For additional assistance and compatibility, use the Total Control & Precision Locking Machine Heads from Graph Tech in conjunction with the Un-Lock Nut.
연락처 정보:
- Web대지: www.graphtech.com
- 이메일 지원: support@graphtech.com
- 전화 지원: 604-940-5353 내선 130
To download additional product measurements and installation instructions, visit the Help Center link under the Support section on the web대지.
특징
- Optimally ramped and angled string slot design (distributes the string tension over the entire string ramp), which allows us to triple the lubrication.
- Waaaaay easier string bends on the Ist to 5th string positions.
- Faster string changes.
- 80% reduced headstock weight.
- No more Allen keys for your nut.
- Improved string to headstock connection (You’ll feel this the first time you play).
- Straightforward upgrade, a final tweak on sanding to flush fit with the edge of the fingerboard, and a drop of white glue.
- The ability to tweak string heights, just like a regular nut.
- 10,12, and 16-inch radius available (more models on the way).
AND, you can finally tweak and tune with your machine heads (locking machine heads recommended, but not mandatory)
잠금 해제 너트 설치 가이드
- 1단계
Remove the strings. Score around every edge of the nut with an exacto knife to prevent lacquer from sticking to the nut or the neck and chipping away.
- 2단계
If the nut is not sitting in a slot, usually a light tap with a small block will set it free. If it is sitting in a slot, gently tap it out sideways using a hammer and a screwdriver.
- 3단계
When it is sticking out the side, pull it out in the same direction with a pair of pliers, like you would a tooth. Scrape or file the nut slot free from old glue and finish residue while making sure that the slot remains square.
- 4단계
See if your new Graph Tech nut fits into the slot without force. If it’s too thick, place a 400600-gritgrit sandpaper face up on a flat surface and sand down the sides of the nut until it fits in the slot snugly, but is easily removable.
- RetuReturn thernthe high and low E strings tto verify therify the correct height. Pushing down on the third note of the low E string should result in a .010″ gap between the string and the first fret; the high E string should be .006″
- 6단계
Once you’ve adjusted the thickness and the height, you just need to sand the ends of the nut so that they are flush with the neck. Use a pencil to mark the ends of the nut that are sticking out. Remove it from the neck and sand it to the marks.
회사 소개
- Web대지:
www.graphtech.com - 지원하다:
support@graphtech.com - 전화 지원:
604-940-5353 내선 130
Graph Tech 제품에 대한 제품 측정 및 설치 지침을 다운로드하려면 상단 메뉴의 지원 섹션 아래에 있는 도움말 센터 링크를 찾으세요. web대지.
자주 묻는 질문
이 제품을 모든 종류의 기타에 사용할 수 있나요?
The product is designed to be compatible with various guitar models, but please ensure compatibility with your specific guitar type before installation.
What do I do if I encounter issues during installation?
In case of any installation difficulties or issues, please reach out to our support team for assistance and guidance.
문서 / 리소스
 |
그래프 테크 잠금 해제 너트 스트링 슬롯 [PDF 파일] 사용설명서 6517, 6518, 6519, 6520, 잠금 해제 너트 스트링 슬롯, 잠금 해제, 너트 스트링 슬롯, 스트링 슬롯, 슬롯 |