FLOWLINE LC92 Series Remote Level Isolation Controller

Selelekela

LC90 & LC92 Series Controllers ke balaoli ba boemo ba ho itšehla thajana ba etselitsoeng ho sebelisoa ka lisebelisoa tse sireletsehileng ka hare ho naha. Lelapa la taolo le fanoa ka litlhophiso tse tharo bakeng sa taolo ea pompo le valve. LC90 Series e fana ka tlhahiso e le 'ngoe ea 10A SPDT mme e ka amohela sensor ea boemo bo le bong joalo ka kenyelletso. LC92 Series e na le 10A SPDT e le 'ngoe le 10A Latching SPDT e le 'ngoe. Sephutheloana sena se lumella tsamaiso ea ho kenya tse tharo e ka etsang ts'ebetso e ikemetseng (ho tlatsa kapa ho se na letho) le ts'ebetso ea alamo (e phahameng kapa e tlaase). Letoto la LC92 e ka boela ea e-ba molaoli oa lintho tse peli tse khonang ho etsa lialamo tse peli (2-high, 2-tlase kapa 1-high, 1-tlase). Kopanya letoto la li-control tse nang le li-sensors le li-fittings tsa boemo.

LIKAROLOANA

• Fail-Safe relay taolo ea lipompo, li-valve kapa lialamo ka ho lieha ho 0.15 ho isa ho 60-metsotsoana.
• Sekoahelo sa polypropylene se ka beoa seporo sa DIN kapa se behiloe ka morao.
• Seta e bonolo e nang le matšoao a LED bakeng sa li-sensor, matla le boemo ba relay.
• Fetolela phetoho e fetola boemo ba relay ho tloha NO ho ea ho NC ntle le ho kopanya hape.
• AC e tsamaisoa

Litlhaloso / Litekanyo

• Phepelo voltage: 120 / 240 VAC, 50 - 60 Hz.
• Tšebeliso: 5 Watts max.
• Maikutlo a kutlo:
  • LC90: (1) phetoho ea boemo
  • LC92: (1, 2 kapa 3) li-switches tsa boemo
• Sesebelisoa sa sensor: 13.5 VDC @ 27 mA ka kenyelletso
• Leseli la LED: Sensor, relay & boemo ba matla
• Mofuta oa ho ikopanya:
  • LC90: (1) SPDT Relay
  • LC92: (2) SPDT Relays, 1 Latching
• Lintlha tsa lebitso: 250 VAC, 10A
• Khokahano e hlahisoang: Khetha NO kapa NC
• Kopana le latch: Khetha On/Off (LC92 feela)
• Ho lieha ho ikopanya: Metsotsoana e 0.15 ho isa ho e 60
• Mocheso oa elektronike.:
  • F: -40 ho isa ho 140 °
  • C: -40 ho isa ho 60 °
• Lintlha tse katiloeng: 35mm DIN (EN 50 022)
• Lintho tse katiloeng: PP (UL 94 VO)
• Sehlopha: Lisebelisoa tse amanang
• Litumello: CSA, LR 79326
• Tšireletseho:
  • Sehlopha sa I, Lihlopha A, B, C & D;
  • Sehlopha sa II, Lihlopha E, F & G;
  • Sehlopha sa III
• Litlhophiso:
  • Voc = 17.47 VDC;
  • Isc = 0.4597A;
  • Ka = 0.494μF;
  • La = 0.119 mH

MOLAOLI LABELS:

DIMENSION:

TŠEBELETSO EA LAOLI:

LAOLA LABEL:

Litlhokomelo tsa Tšireletso

• Mabapi le Buka ena: KA KOPO BALA MANUKATSO KAOFELA PELE O KENYA KAPA O SEBEDISA SEHLAHISO SE. Bukana ena e kenyelletsa lintlha tse mabapi le mefuta e meraro e fapaneng ea Remote Isolation Relay Controllers ho tloha FLOWLINE: LC90 le LC92 series. Likarolo tse ngata tsa ho kenya le ho sebelisa li tšoana pakeng tsa mefuta e meraro. Moo li fapaneng teng, bukana e tla e ela hloko. Ka kopo, sheba nomoro ea karolo ho selaoli seo u se rekileng ha u ntse u bala.
• Boikarabello ba Mosebelisi bakeng sa Polokeho: FLOWLINE e etsa mefuta e mengata ea li-controller, tse nang le litlhophiso tse fapaneng tsa ho hlopha le ho fetola. Ke boikarabello ba mosebelisi ho khetha mofuta oa taolo o loketseng ts'ebeliso, ho o kenya hantle, ho etsa liteko tsa sistimi e kentsoeng, le ho boloka likarolo tsohle.
• Tlhokomeliso e Khethehileng bakeng sa ho Instinsically Safe Institution: Li-sensor tse tsamaisoang ke DC ha lia lokela ho sebelisoa ka lino tse phatlohang kapa tse tukang ntle le haeba li sebelisoa ke molaoli ea bolokehileng joalo ka letoto la LC90. "Sireletsehile ka hare" ho bolela hore molaoli oa letoto la LC90 o entsoe ka ho khetheha hore tlas'a maemo a tloaelehileng li-terminals tsa ho kenya sensor li ke ke tsa fetisa matla a sa sireletsehang.tage ka bakang ho hloleha ha kutlo le ho qhomisa ho phatloha ka pel'a motsoako o itseng oa sepakapaka oa mouoane o kotsi. Ke karolo ea sensor feela ea LC90 e bolokehileng ka botebo. Taolo ka boeona e ke ke ea kenngoa sebakeng se kotsi kapa se phatlohang, 'me likarolo tse ling tsa potoloho (matla a AC le tlhahiso ea relay) ha li etselitsoe ho hokahanya le libaka tse kotsi.
• Latela Mekhoa ea ho Intrinsically Sireletsehile Intrinsically: LC90 e tlameha ho kengoa ka tumellano le likhoutu tsohle tsa lehae le tsa naha, ho latela litataiso tsa morao-rao tsa Khoutu ea Motlakase ea Naha (NEC), ke basebetsi ba nang le laesense ba nang le boiphihlelo ba ho kenya lits'ebetso tse bolokehileng ka kotloloho. Bakeng sa mohlalaample, thapo ea kutlo e tlameha ho feta ka har'a setiiso sa mouoane oa conduit e le ho boloka mokoallo lipakeng tsa sebaka se kotsi le se seng kotsi. Ho feta moo, lithapo tsa sensor ha li khone ho tsamaea ka har'a kotopo efe kapa efe kapa lebokose la mateano le arolelanoang le likhoele tse sa sireletsehang. Bakeng sa lintlha tse ling, ikopanye le NEC.
• Boloka LC90 e le Boemong bo Sireletsehileng ka Hare: Phetoho ho LC90 e tla hlakola waranti mme e ka senya moralo o sireletsehileng oa kahare. Likarolo tse sa lumelloeng kapa litokiso li tla hlakola waranti le boemo bo bolokehileng ba LC90.

BOHLOKOA
Se ke oa hokela lisebelisoa life kapa life tse ling (joalo ka sepoloto sa data kapa sesebelisoa se seng sa ho metha) ho theminale ea sensor, ntle le haeba tlhahlobo ea tekanyo e reiloe hore e bolokehile ka tlhaho. Ho kenya, ho fetola, kapa ho sebelisa letoto la LC90 ka mokhoa o sa nepahalang setsing se hlokang lisebelisoa tse sireletsehileng ho ka baka tšenyo ea thepa, kotsi ea 'mele kapa lefu. FLOWLINE, Inc. e ke ke ea jara boikarabello bakeng sa tleleime efe kapa efe ea melato ka lebaka la ho kenya, ho lokisoa, ho lokisa kapa ho sebelisoa ha letoto la LC90 ke mekha e meng.

• Kotsi ea Tšisinyeho ea Motlakase: Hoa khoneha ho ikopanya le likarolo ho molaoli o nang le matla a phahamengtage, ho baka kotsi e mpe kapa lefu. Matla ohle ho molaoli le li-circuit (s) tseo e li laolang li lokela ho tima pele ho sebetsa ho molaoli. Haeba ho hlokahala ho etsa liphetoho nakong ea ts'ebetso ea motlakase, sebelisa tlhokomelo e feteletseng 'me u sebelise lisebelisoa tsa insulated feela. Ho etsa litokiso ho balaoli ba matla ha ho khothalletsoe. Wiring e lokela ho etsoa ke basebetsi ba tšoanelehang ho latela likhoutu tsohle tse sebetsang tsa naha, tsa naha le tsa lehae.
• Kenya Sebakeng se Omileng: Ntlo ea taolo ha e etselitsoe ho qoelisoa. Ha e kentsoe hantle, e lokela ho hlongoa ka tsela eo ka tloaelo e seng e kopane le mokelikeli. Sheba tšupiso ea indasteri ho etsa bonnete ba hore metsoako e ka qhekellang holim'a ntlo ea balaoli e ke ke ea e senya. Tšenyo e joalo ha e koaheloe ke waranti.
• Relay Contact Reite: Relay e fuoe lintlha tse 10 amp mojaro o hanyetsanang. Meroalo e mengata (e kang enjene nakong ea ho qala kapa mabone a incandescent) e sebetsa ka thata 'me e ka ba le sebopeho sa hona joale se ka bang makhetlo a 10 ho isa ho a 20 tekanyo ea boemo ba eona bo tsitsitseng. Tšebeliso ea potoloho ea ts'ireletso ea mabitso e kanna ea hlokahala bakeng sa ts'ebetso ea hau haeba 10 amp tekanyetso ha e fane ka ample margin bakeng sa maqhubu a joalo a inrush.
• Ho etsa Sisteme e sa atleheng: Etsa mokhoa o sireletsehileng oa ho hloleha o amohelang monyetla oa ho fetisoa kapa ho hlōleha ha motlakase. Haeba motlakase o khaotsoe ho molaoli, o tla fokotsa matla a relay. Etsa bonnete ba hore boemo ba de-energized ea relay ke boemo bo sireletsehileng ts'ebetsong ea hau. Bakeng sa mohlalaample, haeba matla a taolo a lahlehile, pompo e tlatsang tanka e tla tima haeba e hokahane le lehlakore le Tloaelehileng le Bulehileng la relay.

Le hoja relay e ka hare e tšepahala, ho hlōleha ha nako ho ka khoneha ka mekhoa e 'meli: tlas'a mojaro o boima, likhokahano li ka "tsubelloa" kapa tsa khomarela sebakeng se matlafetseng, kapa kutu e ka 'na ea hahoa holim'a lebitso le le leng e le hore e ka etsa joalo. ho se phethe potoloho ha e loketse. Lits'ebetsong tse mahlonoko, lits'ebetso tsa backup tse sa sebetseng le lialamo li tlameha ho sebelisoa ho kenyelletsa sistimi ea mantlha. Litsamaiso tse joalo tsa backup li lokela ho sebelisa mahlale a sensor a fapaneng moo ho khonehang.
Leha bukana ena e fana ka ba bang ba examplithuto le litlhahiso ho thusa ho hlalosa ts'ebetso ea lihlahisoa tsa FLOWLINE, joalo ka mohlalaampLes ke tsa tlhahisoleseling feela mme ha lia rereloa joalo ka tataiso e felletseng ea ho kenya sistimi efe kapa efe e itseng.

Rea qala

BAHOLO: 

Nomoro ea Karolo	Matla	Lintho tse kenang	Alamo Relays	Latching Relays	Mosebetsi
LC90-1001	120 VAC	1	1	0	Boemo bo Phahameng, Boemo bo tlase kapa Tšireletso ea Pompo
LC90-1001-E	240 VAC
LC92-1001	120 VAC	3	1	1	Alamo (Relay 1)     - Boemo bo phahameng, boemo bo tlase kapa ts'ireletso ea pompo Latching (Relay 2) - Tlatsa ka boits'oaro, e se na letho, boemo bo holimo, boemo bo tlase kapa ts'ireletso ea pompo.
LC92-1001-E	240 VAC

240 VAC KHETHA:
Ha o odara mofuta ofe kapa ofe oa 240 VAC oa letoto la LC90, sensor e tla fihla e hlophiselitsoe ts'ebetso ea 240 VAC. Liphetolelo tse 240 tsa VAC li tla kenyelletsa -E ho karolo ea nomoro (ke hore LC90-1001-E).

LITŠOANTŠISO TSA KELETSO E LE NNGWE EA HO PHAHAMA KAPA TLASE:
Single Input Relays e etselitsoe ho amohela lets'oao ho tsoa ho sensor e le 'ngoe ea metsi. E bulela kapa E TŠOA relay ea eona ea ka hare (joalokaha e behiloe ke sesebelisoa sa invert) ho arabela boteng ba metsi, 'me e fetola boemo ba relay hape ha sensor e omme.

• Alamo e Phahameng:
  Invert e TIMA. Relay e tla fana ka matla ha switjha e fetoha Metsi 'me e tla felloa ke matla ha switch e Omella (e feletsoe ke metsi).
• Alamo e Tlase:
  Invert e ON. Relay e tla matlafatsa ha switjha e fetoha e Omeletse (e feletsoe ke metsi) 'me e tla felloa ke matla ha switch e fetoha Metsi.

Li-Relay tsa Input e le 'ngoe li ka sebelisoa hoo e batlang e le mofuta ofe kapa ofe oa lets'oao la sensor: kutlo ea hajoale kapa ho koaloa ha mabitso. Relay ke palo e le 'ngoe, mofuta oa ho lahlela habeli; sesebelisoa se laoloang se ka kopanngoa le lehlakoreng le tloaelehileng le bulehileng kapa le atisang ho koaloa la relay. Nako ea ho lieha ho tloha ho 0.15 ho isa ho metsotsoana e 60 e ka behoa pele relay e arabela ho kenyelletso ea sensor. Lisebelisoa tse tloaelehileng bakeng sa Single Input Relays ke ts'ebetso ea boemo bo holimo kapa e tlase ea ho chencha/alamo (ho bula valve ea drain nako le nako ha boemo ba mokelikeli bo nyolohela sebakeng sa sensor) le ho lemoha ho lutla (ho lla alamo ha ho fumanoa ho lutla, joalo-joalo).

LITŠOANTŠISO TSA HO TLATSOA HABELI KA HO TLATSOA KA SEBELE / PHETISO E HLOKANG:
The Dual Input Automatic Fill/Empty Relay (LC92 series only) e etselitsoe ho amohela matšoao ho tsoa ho lisensara tse peli tsa mokelikeli. E BUA kapa HO TLOA relay ea eona ea ka hare (joalo ka ha e behiloe ke sesebelisoa sa invert) ho arabela boteng ba mokelikeli ho li-sensor ka bobeli, 'me e fetola boemo ba relay hape ha li-sensor ka bobeli li omme.

• Ha ho na letho:
  Latch e ON, 'me Invert e TIMA. Relay e tla matlafatsa ha boemo bo fihla ho switch e phahameng (li-switches ka bobeli li kolobile). Relay e tla fokotsa matla ha boemo bo le ka tlase ho switch e tlase (li-switches ka bobeli li omme).
• Tlatsa ka Moetso:
  Latch e ON, 'me Invert e BUTSE. Relay e tla matlafatsa ha boemo bo le ka tlase ho switjha e ka tlase (li-switches ka bobeli li omme). Relay e tla fokotsa matla ha boemo bo fihla ho switch e phahameng (li-switches ka bobeli li kolobile).

The Dual Input Automatic Fill/Empty Relay e ka sebelisoa hoo e batlang e le mofuta ofe kapa ofe oa lets'oao la sensor: kutlo ea hajoale kapa ho koala mabitso. Relay ke palo e le 'ngoe, mofuta oa ho lahlela habeli; sesebelisoa se laoloang se ka kopanngoa le lehlakoreng le tloaelehileng le bulehileng kapa le atisang ho koaloa la relay. Nako ea ho lieha ho tloha ho 0.15 ho isa ho metsotsoana e 60 e ka behoa pele relay e arabela ho kenyelletso ea sensor. Likopo tse tloaelehileng bakeng sa Dual Input Relays ke ho tlatsa ka mokhoa o itekanetseng (ho qala pompo ea ho tlatsa ka tekanyo e tlaase le ho emisa pompo ka boemo bo phahameng) kapa ts'ebetso ea ho ntša metsi ka mokhoa o itekanetseng (ho bula valve ea drain ka tekanyo e phahameng le valve e koalang boemong bo tlaase).

TATAISO EA MOLAOLI:
Ka tlase ke lethathamo le sebaka sa likarolo tse fapaneng tsa molaoli:

1. Letšoao la matla: LED ena e tala e bonesa ha motlakase oa AC o BUTSE.
2. Lesupa la relay: LED ena e khubelu e tla khantša neng kapa neng ha molaoli a fana ka matla ho relay, ho latela boemo bo nepahetseng ho li-input(s) tsa sensor le ka mor'a tieho ea nako.
3. AC Power terminals: Khokahano ea matla a 120 VAC ho molaoli. Setting e ka fetoloa hore e be 240 VAC ha e lakatsa. Sena se hloka ho fetola jumpers ka hare; sena se kenyelelitsoe karolong ea Tlhophiso ea bukana. Polarity (ho se nke lehlakore le ho chesa) ha ho tsotellehe.
4. Li-terminals (NC, C, NO): Hokela sesebelisoa seo u lakatsang ho se laola (pompo, alamo joalo-joalo) ho li-terminals tsena: phepelo ho terminal ea COM, le sesebelisoa ho terminal ea NO kapa NC kamoo ho hlokahalang. Sesebelisoa se fetotsoeng ha sea lokela ho ba boima bo sa feteng 10 amps; bakeng sa meroalo e sebetsang, motlakase o tlameha ho fokotsoa kapa ho sebelisoe li-circuits tsa tšireletso. Ha LED e khubelu e BUTSE 'me relay e le maemong a matla, NO terminal e tla koaloa 'me NC e tla buloa.
5. Nako ea ho lieha: Sebelisa potentiometer ho beha tieho ho tloha metsotsoana e 0.15 ho isa ho e 60. Ho lieha ho etsahala nakong ea khefu ea switch make le switch.
6. Matšoao a ho kenya: Sebelisa li-LED tsena ho bontša boemo ba WET kapa DRY ea switch. Ha switjha e le WET, LED e tla ba Amber. Ha switch e OMILE, LED e ka ba e Tala bakeng sa li-switches tse nang le motlakase kapa HO TLOA bakeng sa li-switches tsa lehlaka. Tlhokomeliso: Li-switches tsa lehlaka li ka khutlisetsoa morao bakeng sa WET / OFF, DRY / Amber LED pontšo.
7. Fetola switjha: Phetoho ena e khutlisa mohopolo oa taolo ea phetisetso ho latela li-switch: maemo a neng a tloaetse ho fana ka matla ho relay joale a tla fokotsa matla a relay le ka tsela e fapaneng.
8. Latch switch (letoto la LC92 feela): Sesebelisoa sena se etsa qeto ea hore na relay e tla matlafatsoa joang karabelong ea likenyelletso tse peli tsa sensor. Ha LATCH e tima, relay e arabela ho sensor Input A feela; ha LATCH e ON, relay e tla matlafatsa kapa e felise matla ha feela li-switches (A le B) ka bobeli li le maemong a tšoanang.
   (tse metsi kapa tse omileng ka bobedi). Relay e tla lula e tsitsitse ho fihlela li-switches ka bobeli li fetola maemo.
9. Lisebelisoa tsa ho kenya: Hokela lithapo tsa ho chencha ho li-terminals tsena: Hlokomela polarity: (+) ke 13.5 VDC, 30 mA power supply (e hoketsoeng terateng e khubelu ea FLOWLINE powered level switch), le (-) ke tsela ea ho khutla ho tsoa ho sensor ( e hokahaneng le terata e ntšo ea FLOWLINE powered level switch). Ka li-switches tsa boemo bo matla, haeba lithapo li khutlisetsoa morao, sensor e ke ke ea sebetsa. Ka li-switches tsa lehlaka, polarity ea terata ha e na taba.

Wiring

HO KEKETSA LITŠOCHE HO LITEMELA TSA HO KENYA:
Li-switches tsohle tsa FLOWLINE tse bolokehileng ka tlhaho (joalo ka letoto la LU10) li tla hokeloa ka terata e khubelu ho ea ho (+) terminal le Black terata ho ea (-) Theminale.

Pontšo ea LED:
Sebelisa li-LED tse kaholimo ho li-terminals ho bonts'a hore na switch e kolobile kapa e omme. Ka li-switches tse tsamaisoang, Green e bontša hore e omme, 'me Amber e bontša hore e kolobile. Ka li-switches tsa lehlaka, Amber e bonts'a metsi 'me ha ho LED e bontšang hore e omme. Tlhokomeliso: li-switches tsa lehlaka li ka kenngoa ka morao e le hore Amber e bontše boemo bo omileng 'me ha ho LED e bontšang boemo ba metsi.

RELAY LE MATLA A TERMINAL
Ho latela mohlala o khethiloeng, ho tla ba le li-relay tse le 'ngoe kapa tse peli. Leibole ea relay e sebetsa ho li-relay tse peli. Terminal e 'ngoe le e 'ngoe e na le terminal e Tloaelehileng e Bulehileng (NC), Common (C) le e Tloaelehileng e Bulehileng (NO). Relay(s) ke(ke) palo e le' ngoe, mofuta oa ho lahlela habeli (SPDT) o lekantsoe ho 250 Volts AC, 10. Amps, 1/4 Hp.
Hlokomela: Mabitso a relay ke mabitso a 'nete a omileng. Ha ho na voltage fumaneha ka har'a mabitso a relay.
Hlokomela: Boemo bo "tloaelehileng" ke ha khoele ea relay e felloa ke matla 'me LED ea relay e khubelu e tima / e felloa ke matla.

VAC POWER INPUT WIRING:
Terminal ea Matla e haufi le Relay(s). Ela hloko leibole ea Phepelo ea Motlakase, e supang tlhoko ea motlakase (120 kapa 240 VAC) le mohala oa theminale.
Hlokomela: Polarity ha e na taba le theminale ea AC.

FETOHA HO TSOA 120 HO TSA 240 VAC:

1. Tlosa karolo e ka morao ea molaoli 'me ka bonolo u thelle boto ea potoloho e hatisitsoeng ho tloha ntlong. Eba hlokolosi ha o tlosa PCB.
2. Li-jumpers tse fumanehang JWA, JWB le JWC ho PCB.
3. Ho fetohela ho 240 VAC, tlosa li-jumpers ho JWB le JWC ebe u beha jumper e le 'ngoe ho pholletsa le JWA. Ho fetohela ho 120 VAC, tlosa jumper JWA 'me u behe li- jumper ho pholletsa le JWB le JWC.
4. Ka bonolo khutlisetsa PCB ka tlung 'me u nke sebaka se ka morao.

240 VAC KHETHA:
Ha o odara mofuta ofe kapa ofe oa 240 VAC oa letoto la LC90, sensor e tla fihla e hlophiselitsoe ts'ebetso ea 240 VAC. Liphetolelo tse 240 tsa VAC li tla kenyelletsa -E ho karolo ea nomoro (ke hore LC90-1001-E).

Ho kenya

PANEL DIN RAIL MOUNTING:
Selaoli se ka behoa ke phanele e ka morao e sebelisa likurufu tse peli ka masoba a hokellang a lihukung tsa molaoli kapa ka ho khoasolla molaoli ho 35 mm DIN Rail.

Hlokomela: Kamehla kenya selaoli sebakeng seo se sa kopaneng le mokelikeli.

Kopo Examples

ALARM YA BOITWANA:
Sepheo ke ho etsa bonnete ba hore opareitara o tsebisitsoe haeba boemo ba mokelikeli bo oela ka tlase ho ntlha e itseng. Haeba e etsa joalo, alamo e tla lla, e lemosa motho ea sebetsang ka boemo bo tlaase. Ho tlameha ho kengoa sesebelisoa sebakeng seo alamo e tla lla ho sona.
Ts'ebelisong ena, switch ea boemo e tla ba Metsi ka linako tsohle. Ha sesebelisoa sa boemo se fetoha se Omme, lebitso la relay le tla koala ho etsa hore alamo e sebetse. Maemo a tlwaelehileng bakeng sa tshebediso ke hore molaodi a tshware relay e butswe ka alamo e hokeletsweng ka Lebitso le Tlwaelehileng. Relay e tla matlafatsoa, ​​​​leseli la LED le tla buloa 'me Invert e tla tima. Ha sesebelisoa sa boemo se fetoha se Omileng, relay e tla tima matla ho etsa hore lebitso le koalehe ho lumella alamo hore e sebetse.

Ho etsa sena, hokela mocheso o chesang oa alamo lehlakoreng la NC la terminal ea relay ea molaoli. Haeba matla a lahlehile, relay e tla tlosoa, 'me alamo e tla lla (haeba ho ntse ho e-na le matla ho potoloho ea alamo ka boeona).
Hlokomela: Haeba motlakase o khaotsoe ho molaoli ka phoso, bokhoni ba switch switch ea ho tsebisa opareitara ka alamo ea boemo bo tlase bo ka lahleha. Ho thibela sena, potoloho ea alamo e lokela ho ba le matla a sa khaotseng kapa mohloli o mong o ikemetseng oa matla.

ALARM YA BOEMO BO hodimo:
Sebakeng se le seng, tsamaiso ena e ka sebelisoa ho lla alamo ha mokelikeli o fihla boemong bo phahameng, ka phetoho feela sebakeng sa sensor le ho beha mochine oa Invert. Alamo e ntse e hokahane le lehlakore la NC la relay ho lumella alamo ea ho felloa ke matla. Sensor hangata e omme. Boemong bona, re batla hore relay e matlafatsoe e le hore alamo e se ke ea utloahala: ke hore, Red relay LED e lokela ho ba teng neng kapa neng ha Input LED e le Amber. Kahoo re kenya Invert On. Haeba boemo ba mokelikeli bo nyolohela sebakeng se phahameng sa sensor, sensor e tsoela pele, relay de-energies le alamo e utloahala.

Tšireletso ea PUMP:
Ntho ea bohlokoa mona ke ho kenya switch ea boemo ka holim'a phallo ea pompo. Ha feela switch e le Metsi, pompo e ka sebetsa. Haeba switjha e fetoha e omme, relay e tla buleha ho thibela pompo ho sebetsa. Ho thibela puisano ea relay, eketsa tieho e nyane ea relay.
Hlokomela: Ts'ebetsong ena, relay ho pompo e tlameha ho koaloa ha switch ea boemo e le Metsi. Ho etsa sena, hokela relay ka lehlakoreng la NO la relay ebe o beha Invert sebakeng sa OFF. Haeba motlakase o lahlehetsoe ke molaoli, relay e tla fokotsa matla le ho boloka potoloho e bulehile ho thibela pompo ho sebetsa.

HO TLATSA KA MOSEBETSI:
Sistimi ena e na le tanka e nang le sensor ea boemo bo holimo, sensor ea boemo bo tlase, le valve e laoloang ke molaoli. Karolo e 'ngoe ea moralo o nepahetseng oa ho hlōleha bakeng sa tsamaiso ena ke hore haeba matla a lahleheloa ke molaoli ka lebaka leha e le lefe, valve e tlatsang tanka e tlameha ho koaloa. Ka hona, re hokahanya valve ho NO lehlakoreng la relay. Ha relay e matlafatsoa, ​​valve e tla bula ebe e tlatsa tanka. Tabeng ena, Invert e lokela ho ON. Letšoao la relay le tla lumellana ka ho toba le boemo bo bulehileng / bo haufi ba valve.
Ho khetha litlhophiso tsa LATCH le INVERT: Ena ke tsela eo sistimi e tlamehang ho sebetsa ka eona:

• Ha li-sensor tse phahameng le tse tlase li omme, valve e tla buleha (relay energized), e qala ho tlatsa tanka.
• Ha sensor e tlase e koloba, valve e tla lula e bulehile (relay energized).
• Ha sensor e phahameng e koloba, valve e tla koala (relay de-energized.
• Ha sensor e phahameng e omella, valve e tla lula e koetsoe (relay de-energized).

Latch: Tsamaisong efe kapa efe ea li-sensor tse peli, LATCH e tlameha ho ba HO ON.
Hlakola: Ha re bua ka chate ea logic ho Mohato oa Borobeli, re sheba maemo a tla fokotsa matla a relay (ho qala pompo) ha lisebelisoa ka bobeli li le metsi (Amber LEDs). Tsamaisong ena, Invert e lokela ho ON.
Ho khetha likhokahano tsa A kapa B: Ha LATCH e ON, ha ho na phapang e sebetsang lipakeng tsa Kenyeletso A le B, kaha lisensara ka bobeli li tlameha ho ba le lets'oao le ts'oanang e le hore maemo a fetohe. Ha o kopanya karolo efe kapa efe ea li-relay tse peli, ho nahanoa feela ka ho hokela sensor e itseng ho A kapa B ke hore na LATCH e tla tima.

HO HLOKA HO HLOKAHALA KA HO ETSA HORE NA:
Mokhoa o ts'oanang oa sistimi e ka sebelisoa bakeng sa ts'ebetso e se nang letho. Ho sena mohlalaample, re tla sebelisa pompo ho tšolla tanka. Sistimi e ntse e na le tanka e nang le sensor ea boemo bo holimo, sensor ea boemo bo tlase, le pompo e laoloang ke molaoli.

• Hlokomela: Moqapi o hlolehileng o bohlokoa ho
  kopo moo tanka e tlatsitsoeng ka mokhoa o sa reroang. Ho hloleha ha matla ho molaoli kapa lipotoloho tsa pompo ho ka etsa hore tanka e phalle. Alamo e phahameng e sa hlokahaleng e bohlokoa ho thibela ho tlala.
• Hokela pompo ho NO lehlakoreng la relay. Tabeng ena, Invert e lokela ho tima, ha relay e matlafatsoa, ​​​​pompo e tla matha ebe e tšolla tanka. Letšoao la relay le tla lumellana ka ho toba le boemo ba ho tima / ho tima ba pompo.
• Hlokomela: Haeba mojaro oa enjene ea pompo o feta tekanyetso ea relay ea molaoli, ho tlameha ho sebelisoe sekhahla sa stepper sa matla a holimo e le karolo ea moralo oa sistimi.

HO HLAHALA LEAK:
Sesebelisoa sa ho lemoha ho lutla se kentsoe ka har'a sebaka se lipakeng tsa tanka kapa ka lebota le kantle. Phetoho e tla lula e le metsi 99.99% ea nako. Ke feela ha mokelikeli o kopana le switch moo relay e tla atamela ho kenya alamo. Alamo e hokahane le lehlakore la NC la relay ho lumella alamo ea ho felloa ke matla.

Hlokomela: Sensor hangata e omme. Boemong bona, re batla hore relay e matlafatsoe e le hore alamo e se ke ea utloahala: ke hore, Red relay LED e lokela ho ba teng neng kapa neng ha Input LED e le Amber. Kahoo re kenya Invert On. Haeba mokelikeli o kopana le switch, switch ea sebetsa, relay e ntša matla, 'me alamo ea lla.

Sehlomathiso

RELAY LOGIC – HO TLATSA LE HO HLOLA HO SEBELE
Latching relay e tla fetoha feela ha li-switches ka bobeli li le maemong a tšoanang.

Hlokomela: Boemo ba ts'ebeliso (e ka ba ho tlatsa kapa ho lahla) bo ke ke ba netefatsoa ha sesebelisoa se le seng se metsi 'me se seng se omme. Ke feela ha li-switches ka bobeli li le boemong bo tšoanang (bobeli ba Wet kapa bobeli bo omileng) bo ka netefatsang boemo ba relay (ho matlafatsoa kapa ho felloa ke matla) ho etsahala.

RELAY LOGIC - RELAY E ILENG
Relay e tla sebetsa ka kotloloho ho ipapisitse le boemo ba switch ea boemo. Ha phetoho ea boemo e le Metsi, lebone la LED le tla be le ON (Amber). Ha sesebelisoa sa boemo se omme, lebone la LED le tla tima.

Hlokomela: Kamehla hlahloba boemo ba switch ea boemo 'me u bapise boemo boo khahlanong le Input LED. Haeba boemo ba ho fetola boemo (Bo metsi kapa bo omileng) bo lumellana le Input LED, tsoela pele ho relay. Haeba boemo ba ho fetoha ha boemo (Bo metsi kapa bo omileng) bo sa tsamaisane le LED ea ho kenya, joale hlahloba ts'ebetso ea phetoho ea boemo.

LATCH – ON VS OFF:
Relay e ka 'na ea e-ba mochine o ikemetseng (boemo bo phahameng, boemo bo tlaase kapa tšireletso ea pompo) e nang le Latch OFF kapa e ka ba latching relay (automatic fill or empty) le Latch ON.

• Ka Latch OFF, relay e tla arabela feela HO PELETSO A. MOHOO OA B o tla hlokomolohuoa ha Latch e TIMA.
  

  Fetolela TIMA		QETELA
  Kenyo A*	Kenyelletso B*	Relay
  ON	Ha ho Phello	ON
  TLOA	Ha ho Phello	TLOA

  Fetolela ON		QETELA
  Kenyo A*	Kenyelletso B*	Relay
  ON	Ha ho Phello	TLOA
  TLOA	Ha ho Phello	ON

• Ka Latch ON, relay e tla sebetsa ha HO KENYA A le HO PELETSO B di le maemong a tshwanang. Relay e ke ke ea fetola boemo ba eona ho fihlela lintlha tse peli li khutlisa boemo ba tsona.
  

  Fetolela TIMA		Latlisa ON
  Kenyo A*	Kenyelletso B*	Relay
  ON	ON	ON
  TLOA	ON	Ha ho Phetoho
  ON	TLOA	Che Fetola
  TLOA	TLOA	ON

  Fetolela ON		Latlisa ON
  Kenyo A*	Kenyelletso B*	Relay
  ON	ON	TLOA
  TLOA	ON	Ha ho Phetoho
  ON	TLOA	Che Fetola
  TLOA	TLOA	ON

Hlokomela: Li-sensor tse ling (haholo-holo li-buoyancy sensors) li ka ba le matla a tsona a ho inverting ( wired NO kapa NC). Sena se tla fetola logic ea invert switch. Sheba moralo oa sistimi ea hau.

MOLAOLI LOGIC:
Ka kopo sebelisa tataiso e latelang ho utloisisa ts'ebetso ea balaoli.

1. Matla a LED: Etsa bonnete ba hore LED ea matla a Green e ONILE ha motlakase o fanoa ho molaoli.
2. Kenya (li) LED: Li-LED (li) tse kenang ho molaoli e tla ba Amber ha switch(es) e le / e metsi 'me e Tala kapa e TLOA ha switch(e) e omme. Haeba li-LED li sa fetole mokhoa oa ho kenya li-LED, leka ho fetola boemo.
3. Kenyelletso e le 'Ngoe: Ha lebone la LED le tima le ho BONAHALA, lebone la LED le tla fetoha. Ha invert OFF, relay LED e tla ba: HO BUTSOA ha lebone la LED le BULENG 'me le TSHOE ha lebone la LED le TIMA. Ha invert ON, relay LED e tla ba: TIMA ha lebone la LED le BUTSE 'me le BUTSE ha lebone la LED le TIMA.
4. Li-Relay tse Kenyelitsoeng Habeli (latching): Ha lisebelisoa ka bobeli li le metsi (Amber LED's ON), relay e tla matlafatsoa (Red LED ON). Ka mor'a moo, haeba sesebelisoa se le seng se omella, relay e tla lula e le matla. Ke feela ha li-switches ka bobeli li omme (ka bobeli li-amber LED's OFF) moo molaoli a tla fokotsa matla ho relay. Relay e ke ke ea fana ka matla hape ho fihlela li-switches ka bobeli li kolobile. Sheba Chate ea Relay Latch Logic ka tlase bakeng sa tlhaloso e eketsehileng.

TSIETSO NAKO:
Nako ea ho lieha e ka fetoloa ho tloha metsotsoana e 0.15 ho isa ho metsotsoana e 60. Ho lieha ho sebetsa lehlakoreng la Make and Break la relay. Ho lieha ho ka sebelisoa ho thibela ho qoqa ka relay, haholo ha o na le mokelikeli o moferefere. Ka tloaelo, ho potoloha hanyenyane ho ea ka nako ea oache, ho tloha sebakeng sa tsela e khahlano le oache, ho lekane ho thibela puisano ea relay.
Hlokomela: Ho lieha ho na le ho emisa pheletsong e 'ngoe le e 'ngoe ea potoloho ea eona ea 270°.

HO BATLE PHOSO

BOTHATA	THABELO
Li-switches tsa relay feela ho tsoa ho ho kenya A (ho iphapanyetsa ho kenya B)	Latch e koetsoe. Fenya konopo ea latch ho bulela.
Boemo bo fihla ho alamo HO ON, empa relay e TIMA.	Ntlha ea pele, hlahloba ho netefatsa hore lebone la LED le ON. Haeba ho se joalo, hlahloba wiring ho sensor. Ea bobeli, hlahloba boemo ba Relay LED. Haeba ho fosahetse, flip switch ea Invert ho fetola boemo ba relay.
Pompo kapa Valve e tlameha ho emisa, empa ha ho joalo.	Ntlha ea pele, hlahloba ho etsa bonnete ba hore li-LED tse kentsoeng ka bobeli li boemong bo le bong (bobeli ON kapa bobeli OFF). Haeba ho se joalo, hlahloba wiring ho sensor ka 'ngoe. Ea bobeli, hlahloba boemo ba Relay LED. Haeba ho fosahetse, flip switch ea Invert ho fetola boemo ba relay.
Molaoli o tsamaisoa, empa ha ho letho le etsahalang.	Qala ka ho hlahloba Power LED ho etsa bonnete ba hore e Tala. Haeba ho se joalo, hlahloba terata, matla 'me u netefatse hore terminal e lutse ka nepo.

LITEKELO TSA TEKO:

1.888.610.7664
www.calcert.com
sales@calcert.com

Litokomane / Lisebelisoa

FLOWLINE LC92 Series Remote Level Isolation Controller [pdf] Buka ea Taelo LC90, LC92 Series Remote Level Isolation Controller, LC92 Series, Remote Level Isolation Controller, Level Isolation Controller, Isolation Controller, Controller

Litšupiso

• Bukana ea Mosebelisi