Linear Gate Openers CW-SYS Wireless Exit Sensor Ine Sensitivity Adjustments Instruction Manual

ZVIRI MUBOX

1. SENSOR "PUCK"
   
2. INTEGRATOR
   
3. AUGER SKREWS (2)
   
4. CR123A MABHIRI AINE MAPFUPI EBATIRI (2)
   
5. 3' (1 m.) COAXIAL CABLE
   
6. TERMINAL BLOCK SCREWDRIVER
   

ZVINODA

• 12VDC magetsi ekupa

(Chikamu #CW-PSU)

SIRIYERO NHAMBA

Iko kune barcode serial nhamba kumashure kweIntegrator, pasi pepuck, uye pabhokisi rechigadzirwa. Paunenge uchifona kuti utaure nezve chigadzirwa chako, ndapota shandisa imwe yenhamba idzi.

KUGADZIRA MABHIRI/ROW BATRI

1. Shandisa CR123A mabhatiri uye mechi polarity nebhatiri terminal mu puck.
2. Kana mabhatiri akaiswa kumashure, haaite kubata.
3. Sunda mabhatiri munzvimbo zvizere kuti ubate.
4. Dzvanya chibatiso chepurasitiki chebhatiri pamusoro pebhatiri rega rega uye pabhatiri terminal.
5. Sensor inozvigadzira pachayo kana mabhatiri aiswa.

YAkaderera BATTERY

Kana mabhatiri achida kutsiviwa mu sensor, Integrator "inorira" uye LED yayo inopenya RED.
Kana wakakochekera kune ekunze system's zone yekupinda (ona #10 pazasi), rongedza zvaunoda kuratidza yakaderera bhatiri.

TSVANISA MABHARITI OSE.
USASHANDISA RECHARGEABLES.

Kubiridzira

YAKO SYSTEM YARWARWA PAFACTORY.
ZVINHU ZVINHU ZVINHU ZVINOSHANDISWA PAKUTANIDZA ZVIMWE ZVAKAWANDA UNITS

Iwe unogona kubatanidza kusvika kugumi pucks ine unlimited nhamba yeIntegrators

1. Hunza sensor padhuze ne Integrator uye simba kumusoro Integrator (ona #10 pazasi).
2. Push bhatani rekubatanidza pane Integrator (icharamba iri mukuita pairing maminetsi makumi matatu).
3. Simba pasi & simba kumusoro sensor nekubvisa uye nekuisazve bhatiri rimwe (ona #3 pamusoro).
   
4. Integrator inorira 3 nguva kana yapetwa uye ichibuda pairing mode otomatiki.

PANE CHINHU	PASI	MUCHIGARA
	Isa logo parallel kudhiraivha Isa zvishoma pasi pepamusoro• Auger screws yakachengeteka puck Usavhara chivharo chepuck• Rongedza tsvina/uswa kumativi osepuck Chengeta chivharo chepuck chakachena

YAMBIRO: CHENGA CHIVHITIKO CHISINA Tsvina, Uswa, Sinou, NEZVINHU ZVOSE NGUVA DZOSE KUBVIRIRA RADIO SIGNAL KUTARISA!

TEST Mode ye SENSOR PUCK

Test mode inobvumira iyo sensor puck kuti itumire otomatiki chiratidzo cheredhiyo pasina kutsika sensor nemotokari. Izvi zvinobatsira paunenge uchiyedza redhiyo chiratidzo (ona #6 pazasi).

1. Dzvanya uye BATA bhatani pane sensor puck kwemasekonzi maviri
2. Iyo tsvuku LED inopenya sekondi yega yega kana iri muyedzo mode
3. Pachava nekutumirwa kwekukurumidza
4. Kuwedzera kufambisa kuchaitika masekonzi gumi ega ega
5. Test mode inozobuda kana bhatani rikadzvanywa zvakare kwemasekonzi maviri
6. Test mode inozongobuda mushure memaminitsi makumi matatu
   

TESTING RANGE

Sisitimu yako ine redhiyo inosvika 350 tsoka kana kupfuura 1000' mutsara-wekuona.
Kuti uone huwandu mune yako application, edza usati waiswa kwekupedzisira.
Radio range inotsamira pane akati wandei akasiyana:

• Iyo puck inoiswa sei (muvhu kana pamusoro pevhu pane post)
• Zvipingamupinyi zvinovharira chiratidzo cheredhiyo, senge ivhu, miti, foilage, zvivakwa, kongiri, nezvimwe.

Kuedza range:

1. Isa Integrator pedyo nenzvimbo yayo yekupedzisira yekuisa mumba kana gedhi.
2. Iwe unozofanirwa kusimbisa iyo Integrator iri kurira (ona #9 pazasi).
3. Isa sensor muyedzo renji modhi (ona #5 pamusoro).
4. Teerera kuti Integrator itange. Kana zvikasadaro, fambisa sensor padhuze ne Integrator.
5. Iva nechokwadi chekuyedza zvakare nepuck yakaiswa muvhu (ona #8 pazasi).
6. Ungangoda kuwedzera anodzokorora mukati memba (ona #9 pazasi).

KUITA SENSITIVITY

CHETE ARJUST (KUDZIKA) SENSITIVITY KANA KUISA PAKATI PADRIVEWAY (ona #8 pazasi). MUZVIMWE ZVIMWE ZVINHU SHANDISA DEFAULT.

SENSITIVITY ADJUSTMENT
HIGH (Default) Inoona mota inoenda 5 MPH 12-14' kure1 & 2 iri OFF chinzvimbo
MEDIUM Inoona mota inoenda 5 MPH 6-8' kure1 ON & 2 OFF chinzvimbo
LOW Inoona mota inoenda 5 MPH 2-4' kure1 & 2 iri ON chinzvimbo

CHERECHEDZA: KUNYANYA KUNYANYA KUNE NEDIP Switchches muOSITION yekudzima

KUGADZIRA SENSOR PUCK

YAMBIRO: SCREW HOLES MUPUCK ICHARUKA. USANYANYA KUNYANYA NEKUSVIRA PFUTI KANA KUPINDA & KUBUDA KAZVO. KANA ZVIKUKURU ZVIKAMURWA, TENGA ZVIRERE ZVAKASVIRWA ZVAKARERERA, ZVINOITA PLASTIC.

Iyo sensor puck inogona kuiswa munzira, muvhu kana pane chinhu chisingazungunuke (posvo, muti, nezvimwewo).

PANE CHINHU (ona mufananidzo pazasi kuruboshwe)

1. Kana huwandu hwayedzwa (ona #6 pamusoro), chivharo chechigaro chakachengeteka papuck ine screws yakapihwa. Hapafanirwe kuve nemukaha pakati pechivharo nepuck. Chenjerera kuti usabvisa screws ne screw gun. Pedzisa kusimbisa neruoko.
2. Tsvaga muti, positi, kana chimwe chinhu chakananga padivi penzira.
3. Ita shuwa kuti chinhu hachiSIMMOVABLE kana maalarm enhema achaitika.
4. Shandisa maburi ari pazasi ma tabo kuti ukururwe puck kuchinhu.

PASI (ona mufananidzo pazasi kuruboshwe)

1. Kana huwandu hwayedzwa (ona #6 pamusoro), chivharo chechigaro chakachengeteka papuck ine screws yakapihwa. Hapafanirwe kuve nemukaha pakati pechivharo nepuck. Chenjerera kuti usabvisa screws ne screw gun. Pedzisa kusimbisa neruoko.
2. Tsvaga nzvimbo yakananga padivi pe driveway.
3. Chera gomba rakakura zvakaringana mascrews epuck uye auger, zvichiita kuti chivharo chepuck chienzane netsvina.
4. Chengetedza puck muvhu ane auger screws, akapindirana ezasi ma tabo epuck.
   Kana ukatadza kuchengetedza puck, mowers welawn, zvichingodaro zvinodhonza/kuyamwa.
5. Paki uye tamp tsvina yakatenderedza puck, kuve nechokwadi chekuti chivharo chakachena patsvina nemarara ese.

PAKUGADZIRIRA KUBUDA KWEMAHARA, KANA MHUKA KANA VANHU VAKANYANYA PA SENSOR PUCK IKAIKWA PAIPSI, ZVINOGONA KUITA KUTI GEdhi ritivhure. FUNGA KUISA PAPOSI KANA MUDRIVEWAY PANE.

MUCHIGARA (ona mufananidzo pazasi kuruboshwe)

1. Kana huwandu hwayedzwa (ona #6 pamusoro), chivharo chechigaro chakachengeteka papuck ine screws yakapihwa. Hapafanirwe kuve nemukaha pakati pechivharo nepuck. Chenjerera kuti usabvisa screws ne screw gun. Pedzisa kusimbisa neruoko.
   Cherechedza: Kana padyo nepamuchinjika traffic, funga kudzika manzwiro pasi (ona #7 pamusoro)
2. Shandisa 4.5 ″ dhayamita masonry gomba kuti ubore buri repuck. Bore ingangoita 2.75 ″ yakadzika saka chivharo chepuck chichava 1/4 ″ pazasi penzira yepamusoro (saka haigone kudhonzwa nemagejo echando, magejo, nezvimwewo).
3. Dururira loop sealant mugomba, chenjerera kuti usazadze, uye isa puck mugomba.
4. Bata puck pasi nehuremu kusvika sealant yasimba.
5. USADIRIRA sealant pamusoro pepuck lid kana maboss kuti uwane mabhatiri.

INTEGRATOR DIP Switches

Dip switches inodzora ruzha uye inodzokorora modhi pane Integrator.

KUZIVIRA
Batidza dip switch 1 kuti ubatidze ruzha.
Sounder inorira katatu kana mota yaonekwa. Iyo zvakare "inorira" kana sensor puck mabhatiri akadzikira uye achida kutsiviwa.

KUDZOKORORA MODZI
Batidza dip switch 2 ON kushandura Integrator kuita inodzokorora. Mune inodzokorora modhi, iyo unit inoramba ichigashira uye ichidzokorora chero chiratidzo kubva kune iyo sensor kuenda kune Integrator yakaiswa mumba (ona # 11 pazasi). Tsvuku uye yebhuruu LED ichachinjana uye ichiramba ichipenya mune inodzokorora modhi.

KUGADZIRA INTEGRATOR

Yako sisitimu inobatana isina musono nechero chengetedzo / HA system kana yemagetsi gedhi opareta. Kuti ubatanidze, shandisa zvinotevera wiring schematics semirayiridzo:

SECURITY/HOME AUTO SYSTEMS

Integrator inoshandisa 8-24 VAC kana 8-30 VDC. Shandisa chengetedzo/HA system kana gedhi opareta kusimba kana kushandisa chero 12VDC magetsi ekupa. Cartell inotengesa sarudzo yemagetsi magetsi (Chikamu #CW-PS).

UNOFANIRA KUWEDZERA KUCHENGETEKA KUTI UCHISHANDISA CW-SYS YEKUBUDA YEMAHARA.

AUTOMATIC GATE OPERATORS

DUAL EXIT TERMINAL

SINGLE EXIT TERMINAL

KUDZOKORORA MODZI

Kuti uwedzere redhiyo, zvingave zvakafanira kuita iyo Integrator inodzokorora.
Kana iyo chiratidzo kubva sensor puck isiri kusvika kune Integrator:

1. Fambisa iyo sensor padhuze neiyo Integrator, uye/kana
2. Isa inodzokorora mumba pakati pe sensor puck uye Integrator yakabatana nekuchengetedza / imba otomatiki system. Ita zvinotevera:
3. Tenga inosarudzika Integrator uye magetsi ekupa (Chigadzirwa CW-REP).
4. Bvisa chivharo chekuvharira nekunyatsosaidzira ma side tabs mukati.
5. Batanidza magetsi kune materminals 1 & 2 (hapana polarity).
6. Batidza dip switch 2 ON (ona #9 pamusoro). Izvi zvinoisa iyo unit mune inodzokorora modhi. Iwo matsvuku uye ebhuruu maLED anochinja achipenya kuratidza anodzokorora modhi. Icharamba ichigamuchira chiratidzo chega chega kubva kune sensor uye kuendesa (idzokorore) iyo kune Integrator yakaiswa padivi peiyo huru system.
7. Isa inodzokorora muhwindo padyo ne sensor puck.
8. Bvisa dip switch 1 DZIMA kuti udzime sounder.

CHERECHEDZA: Kuodha inodzokorora kit, shandisa chigadzirwa kodhi CW-REP.

Zvinotaurwa Nezvehunyanzvi

Technical Zvinotsanangurwa
	Sensor "Puck"	Mubatanidzi
Simba Zvinodiwa	2 – CR123A mabhatiri (6 V)	8-24VAC; 8-28VDC
Mira ne Current	22 Microamps (μA)	25 mamiriyoniamps (mA)
Alarm Current	130 mamiriyoniamps (mA)	40-80 Mamiriyoniamps (mA)
Relay Nguva	–	2 seconds
Relay Contacts	–	SPDT, NO kana NC (Fomu C)
Relay Contact Rating	–	2 amp/24 VDC (1 mA pa5 VDC min. mutoro)
Radio Range	Yakaedzwa pamusoro pevhu, hapana zvipingamupinyi, kusvika ku2,500 ft.* Yakaedzwa flush nevhu, pasina zvipingamupinyi, kusvika ku1,000 ft.* Shandisa Optional Repeater (CW-REP) kuti uwedzere redhiyo
Bhatiri Hupenyu	1-3 makore*	–
Enclosure Rating	IP68	–
Simba Rating	9.39 toni-simba (8514 kgf)	–
Tembiricha Range	-25° F. – +140° F.(-32° C. – 60° C.)
Dimensions	4.5“ dia. x 2.5“ H(11.43 cm x 6.35 cm)	3.25” L x 2” H x .875” D(8.25 cm x 5.08 cm x 2.22 cm)
Kurema	2 lbs. (90kg)	1 lb (.45 kg)

* Fungidzira chete. Redhiyo uye hupenyu hwebhatiri zvinoenderana nezvakawanda zvakasiyana. Hapana vimbiso.

YAMBIRO: Ichi chigadzirwa chinogona kukufumura kumakemikari anosanganisira Acrylonitrile, inozivikanwa kuHurumende yeCalifornia kukonzera gomarara. Kuti uwane rumwe ruzivo, enda ku www.P65Yambiro.ca.gov.

ZVINOSARUDZWA NEKUNZE GETI ANTENNA

Mune gedhi opareta kumisikidzwa, antenna yakasungirirwa zvakananga kune Integrator inoshanda muzviitiko zvakawanda. Iyo chete nguva iyo isingashande iri mune yakavharwa simbi gedhi opareta inovhara iyo RF chiratidzo. Kana zviri izvo, shandisa iyo inosanganisirwa coaxial tambo uye isa antenna kunze, pane zvinotevera:

1. Dhonza 1/4” gomba mugedhi anoshanda.
2. Isa magumo etambo nemuburi uye shandisa nut kuti ubatanidze kune anoshanda. Ita shuwa kuti rubber gasket inogara kunze pakati peanoshanda newasher.
3. Kurukura antenna pamagumo echirume etambo yekunze opareta.
4. Kurukura kwechirume magumo etambo kune Integrator antenna yekubatanidza.
   

KUDZOSERA ZVINHU

Mutengi: Bata mugadziri wako.

INSTALLER: FANA Usati Wachera UP KANA KUBVA

Call 800-878-7829, Sarudzo 1 yekugadzirisa uye kugamuchira Return Merchandise Authorization (RMA) nhamba. Nyora nhamba yeRMA pabhokisi rekutumira uye chero tsamba inosanganisirwa nechigadzirwa chakaremara.

YAMBIRO: Usatumire MABHABHIRI PAUNODZOSESA CHIKAMU KUCARTELL.

MAKORE MASHANU WARRANTY

Zvese zvigadzirwa zveCartell zvakatenderwa kupesana nehurema mune zvinhu uye kugadzirwa kwemakore mashanu. Iyi waranti haifukidze kukanganisa kunokonzerwa, asi kwete kugumira kune:
mabasa aMwari, kuisa zvisina kufanira, kushungurudzwa, kukuvadzwa kwemoto, mabhizi emagetsi, kutadza kushanda zvakanaka kwechivharo/gasket/battery, kuisa screws, uye maburi ekukurura.

FCC YAMBIRO

Ichi chishandiso chinoenderana nechikamu 15 cheFCC Mitemo. Kushanda kunoenderana nemamiriro maviri anotevera: (1) mudziyo uyu haugone kukonzera kukanganisa kunokuvadza, uye (2) mudziyo uyu unofanirwa kugamuchira chero kukanganisa kunowanikwa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingade. Chero shanduko kana zvigadziriso zvisina kutenderwa nebato rine chekuita nekutevedzwa zvinogona kukanganisa mushandisi simba rekushandisa mudziyo.
CHERECHEDZA: Midziyo iyi yakaedzwa uye yakawanikwa inoenderana nemiganhu yeKirasi B yedhijitari mudziyo, zvichienderana neChikamu 15 cheFCC Mitemo. Iyi miganho yakagadzirirwa kupa dziviriro inonzwisisika kubva mukukanganisa kunokuvadza mukuiswa kwekugara. Mudziyo uyu unogadzira, unoshandisa uye unogona kuvheneka redhiyo frequency simba uye, kana isina kuiswa uye kushandiswa zvinoenderana nemirairo, inogona kukonzera kukanganisa kunokanganisa kufambiswa kweredhiyo. Nekudaro, hapana vimbiso yekuti kukanganisa hakuzoitika mune imwe yekumisikidza.
Kana mudziyo uyu ukakonzera kukanganisa kunokuvadza redhiyo kana terevhizheni, iyo inogona kutariswa nekudzima uye nekubatidza mudziyo, mushandisi anokurudzirwa kuyedza kugadzirisa kukanganiswa neimwe kana anopfuura eanotevera matanho:

• Reorrent kana kutamisa antenna inogamuchira.
• Wedzera kupatsanurwa pakati pemidziyo nemugamuchiri.
• Batanidza midziyo muinobuditsa padunhu rakasiyana nere thr receiver.
• Bvunza mutengesi kana nyanzvi yeredhiyo/TV ine ruzivo kuti ubatsirwe.

Kuti urambe uchiteerana neFCC's RF Exposure nhungamiro, Mudziyo uyu unofanirwa kuiswa uye kushandiswa nedikidiki daro riri pakati pe20cm redhiyata muviri wako: Shandisa chete antenna yakapihwa.

IC Yambiro (Canada): Mudziyo uyu unoenderana neIndasitiri Canada rezenisi-yakasunungurwa RSS mwero(s). Kushanda kunoenderana nemamiriro maviri anotevera: (1) mudziyo uyu haugone kukonzera kukanganisa; (2) mudziyo uyu unofanirwa kugamuchira chero kukanganiswa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingadiwe kwechigadzirwa.

iye mudziyo wakaongororwa inotakurika mudziyo RF kuratidzwa zvinodiwa. Mudziyo unochengetwa kanenge 5 mm kure nemuviri wemushandisi.

FCC ID #: 2AUXCCWIN & 2AUXCCWSN (US)
IC#: 25651-CWIN & 25651-CWSN (Canada)

E3957 AUSTRALIA

CONTACT INFORMATION

CONTACT INFORMATION
TECH SUPPORT/RMAs	800-878-7829
SHIPPING	800-878-7829
ACCOUNTING	800-878-7829
MUKATI kutengeswa	800-878-7829
EMAIL	Sales@ApolloGateOpeners.com
ADDRESS	8500 Hadden Road Twinsburg, OH 44087
WEBSITE	www.ApolloGateOpeners.com

www.LinearGateOpeners.com
800-878-7829
Sales@LinearGateOpeners.com

Zvinyorwa / Zvishandiso

Linear Gedhi Vanovhura CW-SYS Wireless Exit Sensor Ine Sensitivity Magadzirirwo [pdf] Bhuku reMirayiridzo CW-SYS Wireless Exit Sensor Ine Sensitivity Adjustments, CW-SYS, Wireless Exit Sensor Ine Sensitivity Adjustments, Sensor ine Sensitivity Adjustments, Iine Sensitivity Adjustments, Sensitivity Adjustments.

References

• User Manual