ELSEMA MC-Single Double uye Single Gate Controller

Zvinotsanangurwa

• Inokodzera swing uye magedhi ekutsvedza
• Inotsigira kaviri kana imwe mota kushanda
• Operating System: Eclipse Operating System (EOS)
• Masikati neusiku sensor (DNS)
• Motokari kushanda: 24 kana 12 Volt DC
• Inoita mota yakapfava kutanga uye yakapfava kumira
• Kukurumidza uye kugadzirisa simba
• Huru 4-mutsara LCD yechimiro chechiratidzo uye yekumisikidza mirairo
• 1-Bata kutonga kuti zvive nyore kuseta
• Auto profiling uchishandisa hungwaru tekinoroji
• Akasiyana-siyana ekuisa aripo: push bhatani, vhura chete, vhara chete, mira, mufambi, uye Photoelectric Beam.

Mirayiridzo Yekushandiswa Kwechigadzirwa

Installation uye Setup

1. Verenga uye unzwisise mirairo yese zvakanaka usati waiswa.
2. Kuisa uye kuyedzwa kunofanirwa kuitwa nevashandi vakadzidziswa tekinoroji.
3. Ita shuwa kuti yambiro dzese dzekuchengetedza dzinoteverwa kudzivirira kukuvara kana kukuvara kwemidziyo.
4. Chengetedza mirairo yekumisikidza kuitira ramangwana.

Kushandisa Controller

1. Shandisa iyo 1-Touch control kuti zvive nyore kuseta uye kushanda.
2. Tarisa iyo hombe 4-mutsara LCD skrini yekuita mota uye mamiriro ekugadzirisa.
3. Gadzirisa kumhanya, simba, uye mamwe marongero sezvinodiwa zvichienderana negedhi rekushanda zvinodiwa.
4. Shandisa zvakasiyana-siyana zvinowanikwa kune akasiyana gedhi mabasa.

Safety Recommendations

1. Isa midziyo yekuchengetedza senge Photo Magetsi danda uye chengetedzo edge sensor kune otomatiki kuvhura.
2. Ita shuwa kushanda kwakaringana kweyekumisikidza switch yekupinda kana mechanic kumira kwekuwedzera kuchengetedza.

Mibvunzo Inowanzo bvunzwa (FAQ):

Mubvunzo: Chii chandinofanira kuita kana ndikasangana nematambudziko panguva yekuseta?
A: Kana ukasangana nematambudziko panguva yekuseta kana kushanda, tarisa kune iyo yekuseta mirairo yakapihwa. Kana matambudziko akaramba, taura nevashandi vakadzidziswa zvehunyanzvi kuti ubatsirwe.

Features

• Inokodzera swing uye magedhi ekutsvedza
• Kaviri kana imwe injini kushanda
• Eclipse Operating System (EOS)
• Masikati neusiku sensor (DNS)
• 24 kana 12 Volt DC motokari kushanda
• Motor soft start uye soft stop
• Kukurumidza uye kugadzirisa simba
• Huru 4-mutsara LCD kuratidza vatongi mamiriro uye setup mirayiridzo
• 1-Bata kutonga kuti zvive nyore kuseta
• Auto profiling uchishandisa yazvino hungwaru tekinoroji
• Yakasiyana-siyana yekupinza, push bhatani, vhura chete, vhara chete, mira, mufambi uye Photoelectric Beam
• Inotsigira muganho chinja mapindiro kana mechanic kumira
• Inogadziriswa Auto Kuvhara, kuvharidzira mutoro uye kupinda kwevanofamba netsoka
• Inogadziriswa kukiya uye neruremekedzo mwenje kubuda
• Variable photoelectric kuchengetedza danda mabasa
• Yakavakwa-mukati Penta Receiver
• Energy saving mode yekudzikisa mari yekushandisa
• 12 uye 24 Volt DC Inobuda kune magetsi ekushandisa
• Sevhisi counter, password kuchengetedza, zororo modhi uye zvimwe zvakawanda maficha
• Yakavakwa mu12 uye 24 Volt bhatiri charger yemabhatiri ekuchengetedza
• Yakaderera kwazvo standby ikozvino ichiita kuti ive yakanakira magedhi ezuva

Tsanangudzo

• Wagadzirira here Eclipse? Iyo MC's Eclipse inoshanda sisitimu ndeye mushandisi ine hushamwari menyu inofambiswa system inoshandisa iyo 1-touch bhatani kudzora, kuseta uye kumhanya otomatiki magedhi, magonhi uye zvipingaidzo. Inoshandisa hombe 4-mutsara LCD skrini inoratidza kuverenga kwepamoyo kwekuita kwemota uye chimiro chezvese zvinopinda uye zvinobuda.
• Iyo MC controller haingori chizvarwa chinotevera asi indasitiri yemutambo shanduko. Isu taida kugadzira controller iri nyore kushandisa uye inoita chero chero chinhu chinodiwa mugedhi nemusuwo indasitiri. Iyo MC haingori chizvarwa chinotevera asi iyo "Inotevera Shanduko" mugedhi nemusuwo indasitiri inogadzira Eclipse pamusoro pekare kugadzirwa mota dzinodzora.
• Iyi nyowani ine hungwaru mota controller ndiyo yakanakisa match kune yako otomatiki gedhi kana gonhi mota.
• Mutongi ane njere akavakwa kubva pasi, zvichibva pamhinduro yemutengi uye kushandisa tekinoroji yemazuva ano. Nemabasa ayo akapfuma, mutengo une hushamwari hwevatengi uye nekutarisa panguva yekusimudzira kuve nyore kushandisa uye kuseta kunoita kuti mutongi uyu ave bhodhi rekupedzisira kudzora mota dzako.
• Sarudzo dziri nyore dzeElsema yekuwedzera zvidzoreso zviri kure kana chero mhando yePhotoelectric Beams inoitira mushandisi ane hushamwari maitiro, uku uchidzivirira nzira yekuvhara kune accessories.
• Makadhi ekudzora anowanikwa neIP66 yakavharwa epurasitiki yekumisikidzwa kwekunze, mabhatiri ekuchengetedza ane charger kana kadhi chete. Iyo MC inokodzerawo magedhi ezuva neayo akadzika kwazvo standby ikozvino.

Chikamu Nhamba

Chikamu Aihwa.	Zviri mukati		Chikamu Aihwa.	Zviri mukati
MC	Kaviri kana rimwe gedhi uye gonhi controller ye24 / 12 Volt mota inosvika ku120 Watts.		MCv2*	Kaviri kana rimwe gedhi uye gonhi controller ye24 / 12 Volt mota yakakura kupfuura 120 Watts *
MC24E	Kaviri kana imwe chete controller ye 24 Volt mota dzinosanganisira IP66 yakayerwa epurasitiki yakavharirwa uye transformer		MC12E	Kaviri kana imwe chete controller ye 12 Volt mota dzinosanganisira IP66 yakayerwa epurasitiki yakavharirwa uye transformer
MC24E2	Zvakafanana neMC24E plus 24 Volt 2.3Ah bhatiri rekuchengetedza
MC24E7	Zvakafanana neMC24E plus 24 Volt 7.0Ah bhatiri rekuchengetedza		MC12E7	Zvakafanana neMC12E plus 12 Volt 7.0Ah bhatiri rekuchengetedza
Solar Gates
Solar24SP	Solar kit yemagedhi maviri kana imwechete, inosanganisira solar MPPT charger & 24 Volt 15.0Ah bhatiri rekuchengetedza uye 40W solar panel.		Solar12	Solar kit yemagedhi maviri kana imwechete, inosanganisira solar MPPT charger & 12 Volt 15.0Ah bhatiri rekuchengetedza

*Anopfuura zana nemakumi maviri Watts anoshandisa MCv120. Bata Elsema kune zvinokurudzirwa marongero.
MC & MCv2 control kadhi inogona kushandiswa kudzora otomatiki magedhi, magonhi, boom magedhi, otomatiki windows & louvres.

Chimiro cheMenyu

Dzvanya Master Control kwemasekonzi maviri kuti upinde menyu

MC Connection Dhiagiramu

DNS Connection: Pakona yekurudyi yekadhi yekudzora pane chinongedzo cheZuva nehusiku Sensor (DNS). Iyi sensor inowanikwa kubva kuElsema uye inoshandiswa kuona masikati machena. Iyi ficha inogona kushandiswa Auto Kuvhara gedhi husiku, batidza mwenje weruremekedzo kana mwenje pamagedhi ako panguva yehusiku uye zvimwe zvakawanda zvinoda kuonekwa kwemasikati nehusiku.

Magetsi Wiring – Supply, Motors, Battery and Inputs

• Gara uchidzima magetsi usati waita chero waya.
• Ita shuwa kuti wiring yese yapera uye kuti mota yakabatana nekadhi rekutonga.
• Hurefu hwetambo dzetambo dzinokurudzirwa dzinofanira kuva 12mm pazvese zvinongedzo kupuragi mumabhuroko ekupedzisira.
• Dhiagiramu iri pazasi inoratidza kupihwa, mota, bhatiri backup uye mapits anowanikwa uye fekitori yekumisikidza yekumisikidza yega yega.

Kana iwe uri kushandisa michina inomira famba uchienda kuSetup i-Kudzidza Matanho. Skip Limit Switch chikamu. Kana iwe uri kushandisa limit switch ita shuwa kuti yakabatana nemazvo. Iyo kadhi yekudzora inogona kushanda pamwe neinogumira switch yakabatana zvakananga kumakadhi terminal blocks kana munhevedzano nemota.

Before Setup

Iyo MC yekudzora kadhi inogona kuiswa mune dzakasiyana siyana yekuisa setup. Pazasi pane 3 common setup. Izvo zvakakosha kuti usarudze iyo chaiyo yekuseta mhando panguva ye-I-Learn.

1. Hapana muganhu chinja.
   Mune iyi setup, kadhi rinotsamira pane yazvino dhizaini yemota kuti ione iyo yakavhurika zvizere uye yakavharwa zvizere zvinzvimbo. Iwe unofanirwa kugadzirisa margins ako maererano kuti gedhi rizarure zvizere uye rakavharwa. Kuseta migero yakakwira zvakanyanya kunogona kuita kuti mota imire panzvimbo yakavhurika kana yakavharwa. (Ona gwaro rekugadzirisa dambudziko).
2. Gadzirisa ma switch akabatana neKudzora kadhi.
   Iyo yekumisikidza switch inogona kuve Yakajairika Yakavharwa (NC) kana Yakajairika Kuvhurika (NO). Iwe unofanirwa kusarudza iyo chaiyo mhando panguva ye-I-Learn. Mukugadzirisa uku, maswiti emuganhu anoiswa waya zvakananga kune kadhi rekutonga.
3. Limit switches munhevedzano nemota.
   Iyo yekugumira switch yakabatana munhevedzano nemota. Iyo yekugumira switch inobvisa simba kune mota kana yaitwa.

Setup i-Kudzidza Matanho

1. Tarisa paLCD uye tevera mirairo yakaratidzwa.
2. Iyo i-Learning setup inogona kugara ichivhiringwa nebhatani rekumisa kana nekudzvanya Master Control knob.
3. Pinda Menyu 13 kuti utange i-Kudzidza kana makadhi matsva ekudzora anozongokukurudzira kuti uite i-Learning.
4. Kadhi rekutonga richavhura nekuvhara masuwo kana magonhi kakawanda kuti udzidze mutoro uye madaro ekufamba. Iyi ndiyo auto profiling uchishandisa yazvino hungwaru tekinoroji.
5. Buzzer icharatidza kuti kudzidza kwakabudirira. Kana pakanga pasina buzzer tarisa ese mawaya emagetsi kusanganisira magetsi wobva wadzokera kunhanho yekutanga.
6. Kana iwe ukanzwa ruzha mushure me-I-Dzidza, gedhi kana gonhi rakagadzirira kushandiswa.

Limit Swichi
Kana iwe uri kushandisa limit switch ita shuwa kuti yakabatana nemazvo. Iyo kadhi yekudzora inogona kushanda pamwe neinogumira switch yakabatana zvakananga kumakadhi terminal blocks kana munhevedzano nemota. Tarisa madhayagiramu pazasi:Nekumisikidza iyo yekumisikidza inopinza pane yekudzora kadhi inowanzovharwa (NC). Izvi zvinogona kuchinjwa kuti zvive zvakajairika kuvhurika (NO) panguva yekuseta matanho.

Optional Accessory

G4000 - GSM Dialer - 4G Gate Opener
Kuwedzerwa kweiyo G4000 module kuEclipse control makadhi inoshandura mashandiro avo nekuita kuti nharembozha ishande yemagedhi. Kubatanidzwa uku kunobvumira vashandisi kuvhura kure kana kuvhara gedhi nerunhare rwemahara. Iyo G4000 inokwidziridza kurerukirwa, chengetedzo uye kushanda zvakanaka, zvichiita kuti ive yakanaka kukwidziridzwa kwemazuva ano ekutonga masystem.
Ona iyo wiring dhizaini pazasi:

* Batanidza kuVhura yekupinda pane yekudzora kadhi kana Vhura Chete basa rinodiwa

Wiring yekunze mudziyo

Menyu 1 – Auto Close

• Auto Close feature inovhara gedhi mushure mekunge nguva yakatarwa yaverengwa kusvika zero. Iyo kadhi yekudzora ine yakajairika Auto Close uye akati wandei akakosha Auto Close maficha imwe neimwe ine yayo yekuverengera nguva.
• Elsema Pty Ltd inokurudzira Photoelectric Beam kuti ibatanidzwe kune kadhi rekudzora kana chero sarudzo dzeAuto Close dzashandiswa.
• Kana iyo Stop yekupinda yakavhurwa Auto Close yakadzimwa kune iyo kutenderera chete.
• Auto Close timer haiverengere pasi kana Push Bhatani, Vhura kana Photoelectric Beam yekupinda ikabatwa inoshanda.

Menu Aihwa.	Auto Close Features	Factory Default	Adjustable
1.1	Normal Auto Close	Off	1 - 600 masekondi
1.2	Auto Close ne Photoelectric Trigger	Off	1 - 60 masekondi
1.3	Kuvhara Otomatiki mushure meKuvhurika Kuvharirwa	Off	1 - 60 masekondi
1.4	Auto Close mushure mekunge Simba Radzorerwa	Off	1 - 60 masekondi
1.5	Normal Auto Kuvhara pane Sequential Zvipingamupinyi	2	Min = Off, Max = 5
1.6	Auto Close Chete Kana Yakavhurwa Yakazara	Off	Off / On
1.7	Auto Close Chete Husiku neDNS yakabatana	Off	Off / On
1.8	Exit

1. Normal Auto Close
   Gedhi rinovhara mushure mekunge timer iyi yaverenga kusvika zero.
2. Auto Close ne Photoelectric Trigger
   Iyi Auto Close inotanga kuverenga pasi nekukurumidza apo Photoelectric Beam yabviswa mushure mekutsvaga kunyange kana gedhi risina kuvhurika zvakakwana. Kana pasina Photoelectric Beam trigger gedhi harizovhare Auto Close.
3. Kuvhara Otomatiki mushure meKuvhurika Kuvharirwa
   Kana gedhi rikavhurika uye rikarova chinovharidzira kazhinji gedhi rinomira uye rinoramba riri munzvimbo iyi. Kana iyi ficha ikagoneswa chinovharira chinotanga timer kuverenga pasi uye pazero ichavhara gedhi.
4. Auto Close mushure mekunge Simba Radzorerwa
   Kana gedhi rakazaruka mune chero chinzvimbo uye pane kutadza kwemagetsi, kana simba rabatanidzwazve gedhi rinovhara neiyi timer.
5.  Normal Auto Kuvhara pane Sequential Zvipingamupinyi
   Kana iyo yakajairwa Auto Close yakaiswa uye panguva yekuvhara pane chinovharika, gedhi rinomira nekuvhurwazve. Kuseta uku kunoseta huwandu hwenguva iyo gedhi richaedza Kuvhara Auto. Mushure mekuedza muganhu wakaiswa gedhi rinoramba rakavhurika.
6. Auto Close Chete Kana Yakavhurwa Yakazara
   Iyo Auto Close timer haizopedza nguva kunze kwekunge gedhi ravhurwa zvizere.
7. Auto Close Chete Husiku
   Kana iyo DNS yakabatana uye senitivity (Menu 16.8) yakaiswa nemazvo, iyo Auto Close inongoshanda husiku.

Menyu 2 – Pedestrian Access

Kune akati wandei marudzi ePedestrian Access modes. Pedestrian Access inovhura gedhi kwenguva pfupi kuti munhu akwanise kufamba nepagedhi asi asingabvumidze kupinda mumotokari.
Elsema Pty Ltd inokurudzira kuti Photoelectric Beam inofanirwa kunge yakabatana nekadhi rekudzora kana chero sarudzo dzeAuto Close dzashandiswa.

Menu Aihwa.	edestrian Access Features	Factory Default	Adjustable
2.1	Pedestrian Access Yekufamba Nguva	3 seconds	3 - 20 masekondi
2.2	Pedestrian Access Auto Close Time	Off	1 - 60 masekondi
2.3	Pedestrian Access Auto Kuvhara Nguva ine PE trigger	Off	1 - 60 masekondi
2.4	Pedestrian Access Auto Close pane Sequential Obstructions	2	Min = Off, Max = 5
2.5	Kusvika kune Vanofamba netsoka neHold Gate	Off	Off / On
2.6	Exit

1. Pedestrian Access Yekufamba Nguva
   Izvi zvinoseta nguva iyo gedhi rinovhurika kana Pedestrian Access yekupinda yaitwa.
2. Pedestrian Access Auto Close Time
   Izvi zvinoseta countdown timer yekuvhara gedhi otomatiki kana Pedestrian Access yekupinda yaitwa.
3. Pedestrian Access Auto Kuvhara Nguva nePE Trigger
   Iyi Auto Close inotanga kuverenga ichidzika pakangocheneswa Photoelectric Beam mushure memutambi, kana gedhi riri muPedestrian Access chinzvimbo. Kana pasina Photoelectric Beam trigger gedhi rinoramba riri muPedestrian Access chinzvimbo.
4. Pedestrian Access Auto Close pane Sequential Obstructions
   Kana iyo Pedestrian Access Auto Close yakaiswa uye gedhi rinovharika pane chimwe chinhu gedhi rinomira nekuvhurwazve. Kuseta uku kunoseta huwandu hwenguva iyo gedhi richaedza Kuvhara Auto. Mushure mekuedza muganhu wakaiswa gedhi rinoramba rakavhurika.
5. Kusvika kune Vanofamba netsoka neHold Gate
   Kana Pedestrian Access inobata gedhi IRI uye Pedestrian Access yekupinda ikabatidzwa zvachose gedhi rinoramba rakavhurika munzvimbo yePedestrian Access. Vhura kuisa, Vhara kuisa, Push Bhatani rekuisa uye kuremote control zvinodzimwa. Inoshandiswa mune Fire Exit application.

Menyu 3 - Input Mabasa

Izvi zvinokutendera kuti uchinje iyo Polarity yePhotoelectric Beam, mira uye dzikamisa chinja mapindiro.

Menu Aihwa.	Input Mabasa	Factory Default	Adjustable
3.1	Photoelectric Beam Polarity	Kazhinji Yakavharwa	Kazhinji Kuvharwa / Kazhinji Kuvhurwa
3.2	Limit Switch Polarity	Kazhinji Yakavharwa	Kazhinji Kuvharwa / Kazhinji Kuvhurwa
3.3	Misa Input Polarity	Kazhinji Open	Kazhinji Kuvhurika / Kazhinji Kuvharwa
3.4*	Zvekubatsira (M2 Open Limit Terminal)	Yakaremara	Dzima / Kuchengetedza Bump Strip
3.5	Exit

Iyi sarudzo inowanikwa chete kana ichishandiswa kune imwechete gedhi modhi
Motor 2 Open Limit terminal inogona kushandiswa kuisa waya yeElsema's safety bump strip pane imwe gedhi application. Mabasa ayo akafanana neakaiswa mumenyu 12.7.

Menyu 4 - Photoelectric Beam

Iyo Photoelectric Beam kana sensor mudziyo wekuchengetedza unoiswa mhiri kwegedhi uye kana danda rikavharwa rinomisa gedhi rinofamba. Iko kushanda mushure megedhi rinomira rinogona kusarudzwa mune iyi menyu.

Menu Aihwa.	Photoelectric Beam Feature	Factory Default	Adjustable
4.1	Photoelectric Beam	PE Beam inomira uye inovhura gedhi padhuze kutenderera	PE Beam inomira yovhura gedhi padhuze pemhepo.
4.2	Exit

Iyo fekitori yekumisikidza yeiyo PE beam yekuisa "inowanzo kuvharwa" asi izvi zvinogona kuchinjwa kuti zviwanzo kuvhurwa mumenyu 3.
Elsema Pty Ltd inokurudzira Photoelectric Beam kuti ibatanidzwe kune kadhi rekudzora kana chero sarudzo dzeAuto Close dzashandiswa.
Elsema inotengesa mhando dzakasiyana dze Photoelectric Beams. Isu tinotengesa Retro-Reflective uye Kuburikidza neBeam Photoelectric Beams.

Mufananidzo Beam Wiring

Menu 5 - Relay Output Mabasa

Kadhi rekutonga rine maviri relay kubuda, Output 1 uye Output 2. Mushandisi anogona kushandura basa rezvibodzwa izvi kuvhara / kubhureki, mwenje weruremekedzo, sevhisi kufona, strobe (Yambiro) mwenje, kukiya actuator kana gedhi rakavhurika (gedhi harina kuvharwa zvizere. ) chiratidzo.
Kubuda 1 ivoltage yemahara relay inobuda neyakajairwa uye anowanzo kuvhura mazita. Factory default ndeye kukiya / brake kuburitsa basa.
Kubuda 2 ivoltage yemahara relay inobuda neyakajairwa, kazhinji yakavhurika uye inowanzovharika mameta. Factory default ndeye courtesy light function.

Menyu Nha.	Relay Output Basa	Factory Default	Adjustable
5.1	Relay Output 1	Kukiya / Brake	Kiya / BrakeCourtesy Light Service Call—————————————Strobe (Yambiro) LightLocking Actuator Gedhi rakavhurika
5.2	Relay Output 2	Courtesy Chiedza	Kiya / Brake Nezve Chiedza Chiedza Sevhisi CallStrobe (Yambiro) Chiedza Gedhi Vhura
5.3	Exit

Kukiya / Brake Output
Iyo fekitori default yekubuda 1 ndeye kukiya / brake kuburitswa. Kubuda 1 ivoltage-yemahara relay kuonana neakajairwa uye anowanzo kuvhura mabiko. Kuva nazvo voltage-yemahara inokutendera kuti ubatanidze ingave 12VDC/AC, 24VDC/AC kana 240VAC kune yakajairwa. Iyo inowanzovhurwa yekuonana inotyaira mudziyo. Ona dhayagiramu pazasi:

Courtesy Chiedza
Chiyero chefekitari chemwenje weruremekedzo chiri pakubuda 2. Output 2 ivoltage-yemahara relay kusangana neakajairika, anowanzo kuvhurika uye anowanzo kuvharika mameta. Kuva nazvo voltage-yemahara inokutendera kuti ubatanidze ingave 12VDC/AC, 24VDC/AC kana 240VAC inopa kune yakajairika. Iyo inowanzovhurwa yekubata inotyaira mwenje. Ona mufananidzo uri papeji inotevera.

Service Call Output
Pamwe inobuda 1 kana yakabuda 2 inogona kuchinjwa kuita sevhisi yekufona chiratidzo. Izvi zvinokonzeresa kuburitsa kana software sevhisi counter yasvikwa. Inoshandiswa kuzivisa vanoisa kana varidzi kana sevhisi yasvika gedhi. Kushandisa Elsema's GSM inogamuchira inobvumira vanoisa kana varidzi kuwana meseji yeSMS & kufona kana sevhisi yasvika.

Strobe (Yambiro) Chiedza paKuvhura kana Kuvhara
Iyo relay inobuda inovhurwa chero gedhi riri kushanda. Iyo fekitori default ndeye Off. Chero kubuda 1 kana kubuda 2 kunogona kuchinjwa kuita strobe (Yambiro) chiedza. Zvese zviri zviviri zvinobuditswa zvine voltage-yemahara contacts. Kuva nazvo voltage-yemahara inobvumidza iwe kuti ubatanidze ingave 12VDC/AC, 24VDC/AC kana 240VAC inopihwa kune inojairwa kusimbisa strobe light. Ipapo iyo inowanzo kuvhurika yekubata inotyaira mwenje. Ona mufananidzo uri pamusoro.

Kukiya Actuator
Locking actuator mode inoshandisa zvese relay kubuda 1 uye relay goho 2. Izvo 2 zvinobuda zvinoshandiswa kushandura polarity yekuvhara actuator kukiya nekukiinura panguva yekuvhura nekuvhara kutenderera. Munguva isati yavhurika relay kubuda 1 iri "ON" uye panguva yemashure-yekuvhara relay kubuda 2 iri "ON". Pre-kuvhura uye post-kuvhara nguva zvinogadziriswa.

Gedhi Vhura
Iyo relay inobuda inoshandiswa chero nguva iyo gedhi risina kuvharwa zvakakwana. Iyo fekitori default ndeye Off. Zvimwe zvinobuda 1 kana zvinobuda 2 zvinogona kushandurwa kuita gedhi rakavhurika.

Menyu 6 - Relay Output Modes

Menyu 6.1 – Kiya / Mabhureki
Iyo relay inobuda mukuvhara / brake modhi inogona kugadzirwa nenzira dzakasiyana.

Menu Aihwa.	Lock / Brake Modes	Factory Default	Adjustable
6.1.1	Vhura Lock / Brake Activation	2 seconds	1 - 30 seconds kana kubata
6.1.2	Vhara Lock / Brake Activation	Off	1 - 30 seconds kana kubata
6.1.3	Vhura Pre-Lock / Brake Activation	Off	1 - 30 masekondi
6.1.4	Vhara Pre-Lock / Brake Activation	Off	1 - 30 masekondi
6.1.5	Drop Lock	Off	Off / On
6.1.6	Exit

1. Vhura Lock / Brake Activation
   Izvi zvinoseta nguva iyo inobuda inovhurwa. Factory default ndeye 2 seconds. Kuimisa kuti Bate zvinoreva kuti iyo inobuda inobatidzwa kune yakazara nguva yekufamba munzira yakavhurika.
2. Vhara Lock / Brake Activation
   Izvi zvinoseta nguva iyo inobuda inovhurwa. Factory default yakadzimwa. Kuimisa kuti Bate zvinoreva kuti iyo inobuda inobatidzwa kune yakazara nguva yekufamba munzira yepedyo.
3. Vhura Pre-Lock / Brake Activation
   Izvi zvinoseta nguva iyo inoburitsa yaitwa mota isati yatanga munzira yakavhurika. Factory default iri Off.
4. Vhara Pre-Lock / Brake Activation
   Izvi zvinoseta nguva iyo inobuda inogadziriswa mota isati yatanga munzira yepedyo. Factory default iri Off.
5. Drop Lock
   Iyi modhi inofanirwa kuve yakagoneswa kana kudonha kukiya kuchishandiswa. Ichabata kukiya kana masuwo akamiswa pakati pekufamba kwayo.

Menyu 6.2 - Ruremekedzo Chiedza
Iyo relay inobuda mune yekuremekedza modhi inogona kugadziridzwa kubva pamasekonzi maviri kusvika kumaawa gumi nemasere. Izvi zvinoisa nguva iyo mwenje weruremekedzo unoitwa mushure mekunge gedhi ramira. Factory default ndeye 2 miniti.

Menu Aihwa.	Courtesy Chiedza Mode	Factory Default	Adjustable
6.2.1	Nekuda kweChiedza Activation	1 miniti	Masekondi 2 kusvika 18 maawa
6.2.2	Courtesy Chiedza paHusiku Chete neDNS (Zuva neHusiku Sensor) Yakabatana	Off	Off / On
6.2.3	Exit

Menyu 6.3 - Strobe (Yambiro) Chiedza
Iyo relay inobuda mu strobe (Yambiro) chiedza chinoramba "chiri" apo gedhi riri kufamba. Izvi zvinobuda zvinogonawo kugadzirwa kuti zviuye "pa" gedhi risati ratanga kufamba.

Menu Aihwa.	Strobe (Yambiro) Chiedza Mode	Factory Default	Adjustable
6.3.1	Pre-Open Strobe (Yambiro) Chiedza Activation	Off	1 - 30 masekondi
6.3.2	Pre-Close Strobe (Yambiro) Chiedza Activation	Off	1 - 30 masekondi
6.3.3	Exit

1. Pre-Open Strobe Light Activation
   Izvi zvinoseta nguva iyo strobe mwenje inovhurwa gedhi risati rashanda munzira yakavhurika. Factory default iri Off.
2. Pre-Close Strobe Light Activation
   Izvi zvinogadzirisa nguva iyo strobe light inogadziriswa gedhi risati rashanda munzira yepedyo. Factory default iri Off.

Menyu 6.4 - Kufona Sevhisi
Izvi zvinoseta huwandu hwemadhizaini akazara (akavhurika nekuvhara) anodiwa iyo yakavakirwa-mukati buzzer isati yaitwa. Zvakare iyo yekudzora kadhi inobuda inogona kugadziridzwa kuti ishandiswe kana iyo nhamba yekutenderera yapedzwa. Kubatanidza Elsema's GSM inogamuchira kune zvakabuda kunobvumira varidzi kuwana runhare & meseji yeSMS kana sevhisi yasvika.
Kana "Service Call Due" meseji ikaratidza paLCD kufona sevhisi kunodiwa. Mushure mekunge sevhisi yaitwa, tevera mameseji ari paLCD.

Menu Aihwa.	Service Call Mode	Factory Default	Adjustable
6.4.1	Service Counter	Off	Min: 2000 kusvika Max: 50,000
6.4.2	Exit

Menyu 6.5 - Kukiya Actuator
Nguva yekuti relay inoburitsa 1 inotendeuka "pa" gedhi risati ratanga kuvhurika uye nguva iyo relay 2 inotendeuka "pa" mushure mekunge gedhi ravharwa zvizere rinogona kugadziriswa sezviri pazasi:

Menyu Nha.	Kukiya Actuator	Factory Default	Adjustable
6.5.1	Pre-Open Lock Activation	Off	1 - 30 masekondi
6.5.2	Post-Close Lock Activation	Off	1 - 30 masekondi
6.5.3	Exit

Pre-Open Locking Actuator Activation
Izvi zvinoseta iyo nguva relay 1 inovhurwa gedhi risati rashanda munzira yakavhurika. Factory default iri Off.

Post-Close Locking Actuator Activation
Izvi zvinoisa iyo nguva relay 2 inogadziriswa mushure mekunge gedhi ravharwa zvakazara. Factory default iri Off.

Menyu 7 - Special Features

Iyo kadhi yekudzora ine akawanda akakosha maficha ayo anogona kugadziridzwa kune yako chaiyo application.

Menu Aihwa.	Special Features	Factory Default	Adjustable
7.1	Remote Control Vhura Chete	Off	Off / On
7.2	Holiday Mode	Off	Off / On
7.3	Energy Saving Mode	Off	Off / On
7.4	Otomatiki Mira & Vhura paKuvhara	On	Off / On
7.5	Receiver Channel 2 Sarudzo	Off	Kudzima / Chiedza / Vanofamba Netsoka Kuwana / Kuvhara Chete
7.6	Dzvanya uye Bata kuti uwane Open Input	Off	Off / On
7.7	Dzvanya uye Batisisa kuti Yekuvhara Input	Off	Off / On
7.8	Hwindo / Louvre	Off	Off / On
7.9	Kutakurwa Nemhepo	Off	Off / Low / medium / High
7.10	Dzvanya & Bata Remote Channel 1 (Vhura)	Off	Off / On
7.11	Dzvanya & Bata Remote Channel 2 (Vhara)	Off	Off / On
7.12	Stop Input	Misa Gedhi	Mira uye dzokera kumashure kwe1sec
7.13	Exit

1. Remote Control Vhura Chete
   By default control remote inobvumira mushandisi kuvhura nekuvhara gedhi. Munzvimbo dzinopinda veruzhinji mushandisi anofanira kukwanisa chete kuvhura gedhi uye kusanetseka nekurivhara. Kazhinji iyo Auto Close inoshandiswa kuvhara gedhi. Iyi modhi inodzima kuvharika kwezvinodzora zvirimo.
2. Holiday Mode
   Izvi zvinodzima maremote control.
3. Energy Saving Mode
   Izvi zvinoisa iyo kadhi yekudzora kune yakaderera kwazvo yekumira ikozvino iyo inoderedza bhiri rako remagetsi uchiri kuchengetedza zvakajairika mabasa uye mashandiro.
4. Otomatiki Mira & Vhura paKuvhara
   Nekutadza kana gedhi richivharika uye bhatani rekusundidzira kana remote control rinoitwa rinomira nekuvhura gedhi. Kana chimiro ichi chavharwa, gedhi rinongomira pane activation yebhatani rekusundidzira kana kuremote control. Kuvhura otomatiki kuchadzimwa.
5. Receiver Channel 2 Sarudzo
   Iwo anogashira 2nd chiteshi anogona kurongwa kuti adzore mwenje weruremekedzo, kuwana vanofamba netsoka kana inogona kushandiswa kuVhara chete.
6. & 7.7 Dzvanya uye Bata kuti Vhura uye Vhara maInputs
   Kana chimiro ichi chiri PANE mushandisi anofanira kuramba achidzvanya yakavhurika kana kuvhara yekuisa kuti gedhi rishande.
7. Window kana Louvre Mode
   Iyi modhi inokwidziridza kadhi rekutonga rekushandisa otomatiki windows kana louvres.
8. Kutakurwa Nemhepo
   Gonesa iyi modhi yemagedhi akaiswa munzvimbo yepamusoro Mhepo.
9. & 7.11 Dzvanya uye Bata Remote Channel 1 (Vhura) uye Channel 2 (Vhara)
   Mabhatani echiteshi 1 & 2 ari kure achada kurongwa kuti agamuchire chiteshi 1 & 2. Mushandisi anofanira kudzvanya uye kubata bhatani reremote kuti gedhi rivhure kana kuvhara.
10. Stop Input Options
    Kana chimiro ichi CHOKWATIRWA uye kana chimbomira chikaiswa, magedhi ese anomira odzokera kumashure kwesekonzi 1.

Menyu 8 - Kunonoka Kweshizha

Kunonoka kweshizha kunoshandiswa kana shizha regedhi rimwe chete richivharika richipindirana kusvika pashizha rekutanga rakavharwa. Uku kunonoka kweshizha kungave kuri madikanwa kune yakakosha mapini ekukiya. Iyo kadhi yekudzora ine yakaparadzana shizha kunonoka kune yakavhurika uye yepedyo nzira.
Kana iyo kadhi yekudzora ichishandiswa nemota imwechete iyo shizha inononoka modhi inovharwa.

Menu Aihwa.	Leaf Kunonoka	Factory Default	Adjustable
8.1	Vhura Kunonoka Kweshizha	3 seconds	Kudzima - 25 masekondi
8.2	Vhara Kunonoka Kweshizha	3 seconds	Kudzima - 25 masekondi
8.3	Vhara Kunonoka Kweshizha paMid Stop	Off	Off / On
8.4	Exit

1. Vhura Kunonoka Kweshizha
   Motokari 1 ichatanga kuvhurwa. Mushure mekunonoka kweshizha nguva yapera mota 2 ichatanga kuvhurwa.
2. Vhara Kunonoka Kweshizha
   Motokari 2 ichatanga kuvhara. Mushure mekunonoka kweshizha nguva yapera mota 1 inotanga kuvhara.
3. Vhara Kunonoka Kweshizha paMid Stop
   By default mota 1 inogara iine kunonoka kana ichivhara kunyangwe gedhi risina kuvhurwa zvizere. Kana yakaremara zvese mota 1 uye mota 2 zvinotanga kuvhara panguva imwe chete kana isina kuvhurwa zvizere.

Menyu 9 - Motokari 1 Kuvhiringidza Tsvaga Margins

Izvi zvinoseta yazvino senitivity margin pamusoro peyakajairwa kumhanya ikozvino kutsika gedhi kana chipingamupinyi chaonekwa. Yakasiyana yekuvharira miganho inogona kusetwa kune yakavhurika uye yepedyo nzira. Uyewo nguva yekupindura inogadziriswa.
Hudiki hwemuganho huchabvumira kudzvanya kushoma kunoitwa kutsika gedhi kana rikarova chinhu. Iyo yakanyanya margin inobvumira huwandu hukuru hwekumanikidza hwakaiswa kutsika gedhi kana rikarova chinhu.

Menu Aihwa.	Motokari 1 Kuvhiringidza Tsvaga Margins uye Nguva Yekupindura	Factory Default	Adjustable
9.1	Vhura Kuvharisa Margin	1 Amp	0.2-6.0 Amps
9.2	Vhara Chinovhara Margin	1 Amp	0.2-6.0 Amps
9.3	Vhura uye Vhura Slow Speed ​​Obstruction Margin	1 Amp	0.2-6.0 Amps
9.4	Kuvhiringidza Kuona Nguva Yekupindura	Pakati	Inokurumidza, Pakati, Inononoka uye Inononoka Kwazvo
9.5	Exit

Margin Example
Motokari inomhanya kuma2 Amps uye muganho wakaiswa ku1.5 Amps, chivharo chekudzivirira chichaitika pa3.5 Amps (Kazhinji Running Current + Margin).
Kumasetirwo epamusoro emuganho shanduri yekugovera inofanirwa kunge yakakura zvakakwana kuti ipe iyo yakakwira margin ikozvino.
Kana gedhi rikarova chinhu pakuvharwa rinongomira robva ravhurika zvakare. Kana gedhi rikarova chinhu pakuvhurwa rinobva ramira.

Menyu 10 - Motokari 2 Kuvhiringidza Tsvaga Margins

Izvi zvinoseta yazvino senitivity margin pamusoro peyakajairwa kumhanya ikozvino kutsika gedhi kana chipingamupinyi chaonekwa. Yakasiyana yekuvharira miganho inogona kusetwa kune yakavhurika uye yepedyo nzira. Uyewo nguva yekupindura inogadziriswa.
Hudiki hwemuganho huchabvumira kudzvanya kushoma kunoitwa kutsika gedhi kana rikarova chinhu. Iyo yakanyanya margin inobvumira huwandu hukuru hwekumanikidza hwakaiswa kutsika gedhi kana rikarova chinhu.

Menu Aihwa.	Motokari 2 Kuvhiringidza Tsvaga Margins uye Nguva Yekupindura	Factory Default	Adjustable
10.1	Vhura Kuvharisa Margin	1 Amp	0.2-6.0 Amps
10.2	Vhara Chinovhara Margin	1 Amp	0.2-6.0 Amps
10.3	Vhura uye Vhura Slow Speed ​​Obstruction Margin	1 Amp	0.2-6.0 Amps
10.4	Kuvhiringidza Kuona Nguva Yekupindura	Pakati	Inokurumidza, Pakati, Inononoka uye Inononoka Kwazvo
10.5	Exit

Margin Example
Motokari inomhanya kuma2 Amps uye muganho wakaiswa ku1.5 Amps, chivharo chekudzivirira chichaitika pa3.5 Amps (Kazhinji Running Current + Margin).
Kumasetirwo epamusoro emuganho shanduri yekugovera inofanirwa kunge yakakura zvakakwana kuti ipe iyo yakakwira margin ikozvino.
Kana gedhi rikarova chinhu pakuvharwa rinongomira robva ravhurika zvakare. Kana gedhi rikarova chinhu pakuvhurwa rinobva ramira.

Menyu 11 - Mota Yekumhanya, Inononoka Kumhanya Nzvimbo uye Reverse Nguva

Menu Aihwa.	Motor Speed, Slow Speed Nzvimbo uye Reverse Nguva	Factory Default	Adjustable
11.1	Vhura Speed	80%	50% kusvika 125%
11.2	Close Speed	70%	50% kusvika 125%
11.3	Vhura uye Vhura Slow Speed	50%	25% kusvika 65%
11.4	Vhura Slow Speed ​​Area	4	1 kusvika 12
11.5	Vhara Slow Speed ​​Area	5	1 kusvika 12
11.6	Stop Reverse Kunonoka	0.4 seconds	0.2 kusvika 2.5 seconds
11.7	Exit

1. & 11.2 Vhura uye Kuvhara Kumhanya
   Izvi zvinogadzirisa kukurumidza kwegedhi. Kana gedhi riri kufamba nekukurumidza kuderedza kukosha uku.
2. Slow Speed
   Izvi zvinogadzirisa sipidhi iyo gedhi richafamba munzvimbo inononoka. Kana gedhi riri kufamba zvishoma nezvishoma wedzera kukosha uku.
3. & 11.5 Slow Speed ​​​​Area
   Izvi zvinoseta nzvimbo inononoka yekufamba. Kana iwe uchida nguva yakawanda yekufamba yenzvimbo inononoka wedzera kukosha uku.
4. Kuvhiringidza Stop Reverse Kunonoka Nguva
   Izvi zvinoseta kumira uye kudzosera kumashure nguva yekunonoka kana gedhi rarova chinovharidzira.

Menyu 12 - Anti-Jam, Electronic Braking uye Gedhi Movement mushure mekuvharwa

nu Aihwa.	Anti-Jam kana Electronic Braking	Factory Default	Adjustable
12.1	Motokari 1 Vhura Anti-Jam	DZIMA	0.1 kusvika 2.0 seconds
12.2	Motokari 1 Vhara Anti-Jam	DZIMA	0.1 kusvika 2.0 seconds
12.3	Motokari 2 Vhura Anti-Jam	DZIMA	0.1 kusvika 2.0 seconds
12.4	Motokari 2 Vhara Anti-Jam	DZIMA	0.1 kusvika 2.0 seconds
12.5	Electronic Braking	DZIMA	Off / On
12.6	Kuvhura Direction: Gedhi Movement mushure mekuvharirwa	Gate Rinomira	Mira / Reverse for 2 sec / Reverse Fully
12.7	Kuvhara Nhungamiro: Gedhi Movement mushure mekuvharwa	Reverse for 2 seconds	Mira / Reverse for 2 sec / Reverse Fully
12.8	Exit

• uye 12.2 Motokari 1 Vhura uye Vhara Anti-Jam
  Kana gedhi rave rakavhurika zvakazara kana kuvharwa zvakazara chimiro ichi chinoshandisa reverse voltage kwenguva pfupi. Iyo inodzivirira mota kuti isajambuke gedhi saka zviri nyore kubvisa mamotors ekushanda kwemanyorero.
• uye 12.4 Motokari 2 Vhura uye Vhara Anti-Jam
  Kana gedhi rave rakavhurika zvakazara kana kuvharwa zvakazara chimiro ichi chinoshandisa reverse voltage kwenguva pfupi. Iyo inodzivirira mota kuti isamedze gedhi saka zviri nyore kuita
  bvisa injini dzekushanda kwemanyore.
• Electronic Braking
  Izvi zvinomisa mota nemagetsi brake. Brake inoshanda pakuvhara uye Stop inputs.
• Kuvhura Direction: Gedhi Movement mushure mekuvharirwa
  Mushure mekunge kuvharidzirwa kwaitika pakuvhurwa, gedhi rinomira, reverse for 2 seconds kana
  reverse zvizere.
• Kuvhara Nhungamiro: Gedhi Movement mushure mekuvharwa
  Mushure mekunge chipingamupinyi chaitika pakuvhara, gedhi rinomira, reverse for 2 seconds kana kudzokera kumashure zvizere.

Menyu 13 - i-Kudzidza

Iyi ficha inobvumidza iwe kuti uite hungwaru hwekufamba kudzidza kwegedhi. Tevedzera mameseji ari paLCD kuti upedze kudzidza

Menyu 14 - Password

Izvi zvinobvumira mushandisi kuisa password kuti adzivise vashandisi vasina kubvumidzwa kupinda mukati mekutonga kadhi marongero. Mushandisi anofanira kuyeuka password. Nzira chete yekugadzirisa password yakarasika ndeyekutumira kadhi rekudzora kuElsema.
Kudzima password sarudza Menyu 14.2 wodzvanya Master Control.

Menyu 15 - Operational Records

Izvi ndezveruzivo chete.

Menu Aihwa.	Operational Records
15.1	Chiitiko Nhoroondo, kusvika ku100 zviitiko zvakanyorwa mundangariro
15.2	Inoratidza Mashandiro Egedhi uye Mazinga Ezvino
15.3	Reset Maximum Current Records
15.4	Exit

• Chiitiko History
  Nhoroondo yechiitiko ichachengeta zviitiko zve100. Zviitiko zvinotevera zvinorekodhwa mundangariro: Power On, Low Battery, All input activations, Kubudirira Kuvhura, Kubudirira Kuvhara, Kuvharisa kwaonekwa, Kusabudirira i-Learning Kuedza, Factory Reset, DC Output Yakawandisa, AC Supply Yakundikana, AC Supply Restored, Autoclose , Chengetedzo Yekuvhara uye Fuse Dzivirira Kuvhiringidza.
• Inoratidza Mashandiro uye Manhanho Azvino
  Izvi zvinotaridza huwandu hwematenderedzwa akavhurika, matenderedzwa akavharika, mafambiro evanofamba netsoka, zvivhariso zvakavhurika, zvivhariso zvekuvhara uye ese ari maviri mota mazinga. Yese yakakwira kukosha kwazvino inogona kusetwa zvakare nemushandisi muMenu 15.3

Menyu 16 - Zvishandiso

Menu Aihwa.	Zvishandiso
16.1	Nhamba yeMotor, Imwe kana Double Gate System
16.2	Seta iyo Supply Voltage : 12 kana 24 Volts
16.3	Reset Controller kuFactory Settings
16.4	Test Inputs
16.5	Kufamba Nguva yeSlip Clutch Motors
16.6	Solar Gedhi Modhi: Inokwidziridza iyo Kadhi Yekudzora yeSolar Application
16.7	Fuse Type: 10 kana 15 Amps Inokwiridzira Kadhi reKudzora kune chaiyo Blade Fuse inoshandiswa
16.8	Masikati nehusiku Sensitivity Kugadziriswa kweiyo DNS
16.9	Slow Speed ​​Ramp Down Time
16.10	Exit

1. Nhamba yeMotors
   Izvi zvinokutendera kuti uise nemaoko kadhi rekutonga kune imwechete kana kaviri mota. Iyo kadhi yekudzora inozviyedza yega mota dzakabatana panguva yekuseta.
2. Seta iyo Supply Voltage
   Izvi zvinokutendera kuti uise nemaoko kadhi rekutonga ku12 kana 24 Volt. Iyo kadhi yekudzora inozoisa otomatiki iyo chaiyo yekugovera voltage panguva yekugadzirisa. Kuti ushandise kadhi rekutonga mune solar application unofanirwa kuseta iro chairo voltage muZvishandiso. Izvi zvinodzima otomatiki voltage sensing izvo zvinogona kukonzera matambudziko mukushandiswa kwezuva.
3. Reset Controller
   Gadzirisa zvigadziriso zvese kufekitari default. Uyewo inobvisa password.
4. Test Inputs
   Izvi zvinokutendera kuti uedze ese ekunze maturusi akabatana neanodzora mapipu. UPPERCASE zvinoreva kupinza kunobatidzwa uye mavara madiki zvinoreva kuti kuisa kunovharwa.
5. Kufamba Nguva yeSlip Clutch Motors
   Izvi zvinokutendera kuti ushandise mutongi ane nguva dzekufamba. Motokari 1 uye 2 inogona kuva nenguva dzekufamba dzakasiyana kusvika kumasekonzi zana nemakumi maviri. Inoshandiswa kune Hydraulic Motors.
6. Slow Speed ​​Ramp Down Time
   Izvi zvinokubvumira kuti uchinje nguva iyo inotora gedhi kuti ichinje kukurumidza kwayo kubva pakukurumidza kusvika kunonoka.

LCD Ratidza Inotsanangurwa

Gate Status	Tsanangudzo
Gedhi Rakavhurwa	Gedhi riri panzvimbo yakavhurika zvizere
Gedhi Rakavharwa	Gedhi riri munzvimbo yakavharwa zvizere
Gate Rakamira	Gate rakamiswa neimwe yezvipindiro kana remote control
Kuvhiringidza Kwaonekwa	Kadhi rekudzora ranzwa kuvharika
Limit Switch Status	Tsanangudzo
M1OpnLmON	Motokari 1 Open limit switch iri ON
M2OpnLmON	Motokari 2 Open limit switch iri ON
M1ClsLmON	Motor 1 Close limit switch is ON
M2ClsLmON	Motor 2 Close limit switch is ON
Input Status	Tsanangudzo
Vhura ON	Kuvhura kupinza kwaitwa
Cls ON	Kuvhara kupinza kwaitwa
Stp ON	Stop input yaitwa
PE ON	Photo Beam yekupinda yakavhurwa
PB ON	Push Bhatani rekuisa rakabatidzwa
PED ON	Pedestrian Access input yaitwa

Dambudziko rekugadzirisa

Panguva ye-I-Learn, gedhi rinovhurika nekuvhara 3 nguva. First cycle iri mu slow speed. Yechipiri kutenderera iri kumhanya nekukurumidza. Yechitatu kutenderera ichave inokurumidza kukurumidza asi gedhi richanonoka risati rasvika kumagumo.

Kukanganisa panguva ye-I-Learn	Remedy
i-Learn yakanamatira pa14%	Deretsa M1 uye M2 Slow Speed ​​Obstruction Margin (Menu 9.3 & 10.3)
i-Learn yakanamatira pa28%	Deredza M1 uye M2 Vhura Kuvhara Margin (Menu 9.1 & 10.1)
Magedhi haavhure zvizere kana kuvhara zvizere mukutanga i-Learn kutenderera	Wedzera M1 uye M2 Slow Speed ​​Obstruction Margin (Menu 9.3 & 10.3)
Magedhi haavhurike zvizere kana kuvharika zvizere muchikamu chechipiri i-Learn	Wedzera M1 uye M2 Vhura kana Kuvhara Kuvhara Margin (Menu 9.1, 9.2 & 10.1, 10.2)
Limit switch yatadza kunyoresa uye gedhi harisi munzvimbo yakazaruka kana kuvharika zvakazara.	Yekutanga kutenderera. Wedzera M1 uye M1 Slow Speed ​​Obstruction Margin (Menu 2 & 9.3). Yechipiri & 10.3rd kutenderera. Wedzera M2 uye M3 Vhura kana Kuvhara Kuvhara Margin (Menu 1, 2 & 9.1, 9.2)
Limit switch yatadza kunyoresa uye gedhi riri panzvimbo yakavhurika zvizere kana kuvharika.	Limit switch position haina kunaka. Gedhi rasvika panomira kana kuti rwendo rwakanyanya rusati rwaitwa.
Kukanganisa panguva yeKushanda	Remedy
Gedhi harina kuvhurika zvakazara kana kunyatsovhara asi LCD inoti “Gedhi Rakavhurwa” kana “Gedhi Rakavharwa”.	Wedzera M1 uye M2 Slow Speed ​​Obstruction Margin (Menu 9.3 & 10.3) zvichienderana nekuti ndeipi mota isina kunyatsovhura kana kuvhara.
LCD inoti "Chipingamupinyi chaonekwa" kana pasina chinodzivisa.	Wedzera M1 uye M2 Vhura kana Kuvhara Kuvhara Margin (Menu 9.1, 9.2 & 10.1, 10.2)
Gedhi haripindure kumaremote kana chero chinokonzeresa chemuno.	Tarisa LCD yezvimiro zveInput (ona peji yapfuura). Kana chero mapindiro akaiswa uye akabatwa achishanda, kadhi harizopindura kune chero mumwe murairo.

Accessories

• Chengetedza Mabhatiri & Bhatiri Charger
  Kadhi rekudzora rine yakavakirwa muchaja yemabhatiri ekuchengetedza. Ingobatanidza mabhatiri kune bhatiri terminal uye charger inozochaja mabhatiri otomatiki. Elsema ine huwandu hwehukuru hwebhatiri.
• Solar Zvishandiso
  Elsema inochengetera solar gedhi controller kits, solar panel, solar charger uye yakazara solar gedhi vanoshanda zvakare.
• YAMBIRO
  Kuti ushandise kadhi rekutonga mune solar application unofanirwa kuseta iro chairo voltage kupinza muZvishandiso Menyu (16.2). Izvi zvinodzima otomatiki voltage sensing izvo zvinogona kukonzera matambudziko mukushandiswa kwezuva.
• Pre-yakagadzirwa Inductive Loops & Loop Detector
  Elsema ine huwandu hweSaw-Cut uye Direct Burial loops. Iwo akafanoumbwa ane akakurudzirwa loop saizi yekutengeserana kana yemumba maapplication uye inoita kuti kuisirwa kuve nekukurumidza uye nyore.
• Wireless Bump Strip
  Chengetedzo edge bump strip inoisirwa pagedhi rinofamba kana chipingamupinyi pamwe chete nemupepeti. Kana gedhi rarova chipingamupinyi, mutakuridzi anotumira chiratidzo chisina waya kune anogamuchira kuti amise gedhi kubva pakukonzera kumwe kukuvadza.

Keyring Remotes
Iyo yazvino PentaFOB® keyring remotes inova nechokwadi chekuti magedhi ako kana magonhi akachengeteka. Visit www.elsema.com kuti uwane mamwe mashoko. PentaFOB® Chirongwa
Wedzera, gadzirisa uye dzima PentaFOB® maremote kubva mundangariro yemugamuchiri. Iyo inogamuchira inogona zvakare kuchengetedzwa pasiwedhi kubva kune isina mvumo yekuwana. Kupenya Mwenje
Elsema ine marambi akawanda anopenya ekuita seyambiro kana gedhi kana magonhi ari kushanda.

PentaFOB® Programming Instructions

1. Dzvanya uye bata bhatani rechirongwa pane yakavakirwa-mukati inogamuchira (Tarisa kune MC yekubatanidza dhizaini)
2. Dzvanya bhatani reremote kwemasekonzi maviri wakabata bhatani rechirongwa pane inogamuchira
3. Receiver LED inopenya uye yobva yashandura Green
4. Sunungura bhatani pamugamuchiri
5. Dzvanya bhatani reremote control kuti uedze chinobuda

Kudzima Receivers Memory
Pfupi iyo Code Reset pini pane inogamuchira kwemasekonzi gumi. Izvi zvinodzima maremote ese kubva mundangariro yemugamuchiri.

PentaFOB® Chirongwa
Iyi programmer inobvumidza iwe kuti uwedzere uye udzime mamwe maremote kubva kune inogamuchira memory. Izvi zvinoshandiswa kana remote control yarasika kana muroja atama kubva panzvimbo uye muridzi achida kudzivirira kupinda kusina mvumo.

PentaFOB® Backup Chips
Iyi chip inoshandiswa kuchengetedza kana kudzoreredza zvirimo zveanogamuchira. Kana paine 100's yemaremotes akarongerwa kune anogamuchira mugadziri anowanzo chengetedza memory yekugamuchira kana iyo inogamuchira yakanganiswa.

ELSEMA PTY LTD
31 Tarlington Nzvimbo Smithfield, NSW 2164
Ositireriya

Zvinyorwa / Zvishandiso

ELSEMA MC-Single Double uye Single Gate Controller [pdf] Bhuku reMirayiridzo MC-Double, MC-Single, MC-Single Double uye Single Gate Controller, MC-Imwe chete, Kaviri uye Mutariri Wegedhi Rimwechete, Mutongi Wegedhi Rimwechete, Mutongi Wegedhi, Mutongi

References

• User Manual