ProPlex CodeBridge TimeCode Or Midi Over Ethernet
- TMB authorizes its customers to download and print this electronically published manual for professional use only.
- TMB нусхабардорӣ, тағир додан ё паҳн кардани ин ҳуҷҷатро барои ҳама гуна мақсадҳои дигар, бе розигии хаттии мустақим манъ мекунад.
- Specifications are subject to change without notice. The information in this document supersedes all previously supplied information before the effective date listed below. TMB has confidence in the accuracy of the document information herein but assumes no responsibility or liability for any loss occurring as a direct or indirect result of errors or exclusions whether by accident or any other cause.
The ProPlex CodeBridge is a member of our LTC Device system which is designed to generate, distribute and monitor timecode. Our rugged, compact mini-enclosure design is perfect for desktop programmers to throw in bag while also being flexible enough to install in a rack with an optional RackMount Kit. Drop a CodeBridge anywhere you need to share a fully synchronized timecode stream between multiple departments and other TMB LTC devices on the network.
ХУСУСИЯТХОИ АСОСЙ
- Theoretically unlimited number of CodeBridges possible on the same network
- OLED control panel with intuitive user interface and LTC clock, oscilloscope, and level display
- Remote access and configuration via ProPlex Software GUI* or built-in web саҳифа
- Interface options include the ability to name and select between multiple CodeBridge sources*
- Two transformer-isolated XLR3 LTC outputs. Adjustable output level (-18dBu to +6dBu)
- Front panel status LEDs for Ethernet, MIDI and LTC
- Compact, lightweight, rugged, reliable. Backpack friendly
- Available rackmount kit options
- Redundant power – USB-C and PoE
*RTP MIDI, ProPlex Software functionality and naming and selecting of sources will be added in future firmware updates
Рамзҳои фармоиш
| ҚИСМ РАКАМХО | PROUDCT NAME |
| PPCODEBLME | PROPLEX CODEBRIDGE |
| PP1RMKITSS | 1U RACKMOUNT KIT, SMALL, SINGLE |
| PP1RMKITSD | 1U RACKMOUNT KIT, SMALL, DUAL |
| PP1RMKITS+MD | PROPLEX 1U DUAL COMBINATION SMALL + MEDIUM |
МОДЕЛИ БАРГАШТVIEW
FULL DIMENSIONAL WIREFRAME DRAWINGS
ТАШКИЛ КАРДАН
Чорабиниҳои бехатарӣ
Лутфан ин дастурҳоро бодиққат хонед.
Ин дастури корбар дорои маълумоти муҳим дар бораи насб, истифода ва нигоҳдории ин маҳсулот мебошад
- Боварӣ ҳосил кунед, ки дастгоҳ ба ҳаҷми дуруст пайваст шудаастtagд, ва он сатр ҷилдиtage аз он чизе, ки дар мушаххасоти дастгоҳ нишон дода шудааст, баландтар нест
- Боварӣ ҳосил кунед, ки ҳангоми кор дар наздикии дастгоҳ маводи сӯхтанӣ нест
- Ҳангоми овезон кардани арматура ҳамеша сими бехатариро истифода баред
- Пеш аз хидматрасонӣ ё иваз кардани сӯзишворӣ ҳамеша аз манбаи барқ ҷудо кунед (агар лозим бошад)
- Ҳарорати максималии муҳити зист (Ta) 40°C (104°F) аст. Дастгоҳро дар ҳарорати болотар аз ин нишондод кор накунед
- Дар сурати пайдо шудани мушкилоти ҷиддии корӣ, истифодаи дастгоҳро фавран қатъ кунед. Таъмир бояд аз ҷониби кормандони ботаҷриба ва ваколатдор анҷом дода шавад. Ба наздиктарин маркази ваколатдори кӯмаки техникӣ муроҷиат кунед. Танҳо қисмҳои эҳтиётии OEM бояд истифода шаванд
- Дастгоҳро ба бастаи диммер пайваст накунед
- Боварӣ ҳосил кунед, ки сими барқ ҳеҷ гоҳ печида ё вайрон нашудааст
- Ҳеҷ гоҳ сими барқро бо кашидан ё кашидани сим ҷудо накунед
Огоҳӣ! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please see the limited warranty information at the end of this document
КУШОДАН
Upon receipt of the unit, carefully unpack the carton and check the contents to ensure that all parts are present and in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear to be damaged from shipping or if the carton itself shows signs of mishandling. Save the carton and all packing materials. If a unit must be returned to the factory, it is important that it be returned in the original factory box and packing.
ЧИ ДАРОМАД
- ProPlex CodeBridge
- Сими USB-C
- Нигоҳдори кабел clamp
- QR Code downloads card
ТАЛАБОТИ КУВВА
The ProPlex CodeBridge has redundant power connections.
- Power the device via a USB-C cable connected to any standard 5 VDC wall charger or computer USB port
- Supply Power over Ethernet (PoE) by connecting the CodeBridge Ethernet port to any PoE enabled switch or injector.
In some cases, you may want to utilize both connections. Units powered via PoE allow access to the web browser via any computer connected to the same network. Additionally, all connected CodeBridge devices will share stream data via Ethernet. USB-C connections allow for MTC data communication as well as power-IN.
МОНТАЖ
The ProPlex CodeClock enclosure was designed with the touring programmer in mind. We wanted these devices to be lightweight, packable and stackable – so we fitted them with oversized rubber feet to keep them stationary on most surfaces These units are also compatible with Small RackMount Kits should they need to be semi-permanently mounted for touring applications
RACKMOUNT INSTALLATION INSTRUCTIONS
ProPlex RackMount Kits are available for both Single-Unit and Dual-Unit mounting configurations To fasten the rack ears or joiners to the ProPlex PortableMount chassis, you must remove the two chassis screws on each side at the front of the chassis. These same screws are used to securely fasten the RackMount ears and joiners to the chassis For dual-unit configurations, both sets of front and rear chassis screws will be used
МУҲИМ : Be sure to reinsert the screws into the unit after ears have been removed. Store RackMount Kit in a safe location until needed again. Spare screws are available from TMB if needed
RACKMOUNT INSTALLATION INSTRUCTIONS
The Single-Unit Small RackMount Kit is comprised of two rack ears, ONE long and ONE short. The diagram below depicts the completed installation of the RackMount Kit. These rack ears are designed to be symmetrical, so that the short and long ears can be interchangeable
The Dual-Unit Small RackMount Kit has TWO short rack ears plus TWO joiners. The diagram below depicts the completed installation of the RackMount Kit. This configuration requires the TWO center joiners attached at both front and rear
INSTALLING THE DUAL JOINERS
The Dual-Unit Small RackMount Kit includes FOUR joining links and FOUR countersunk flat head screws. These links are designed to nest into each other and are secured with the included screws and threaded holes. Each link piece is identical. Simply rotate the joining link and line up the installation holes to install on either the left or right side of the corresponding unit.
АМАЛИЁТ
The ProPlex CodeBride can be easily configured with the onboard OLED Display and navigation buttons on the front of the unit
ЭКРАНХОИ ХОНА
The CodeBridge has 3 separate HOME SCREENS that display different parameters of incoming timecode streams. Cycle between these screens by pressing either the 
тугма
- Экрани асосӣ 1
The incoming LTC IN stream is displayed at the top of the screen while the bottom area shows oscillogram and voltage level bar to indicate signal level from the LTC source only
Note: Ideally the LTC IN steam should resemble a square wave with high output level. If level is too low, try increasing the volume at the source to improve the signal - Экрани асосӣ 2
This screen displays all sources of timecode that the CodeBridge can detect
The topmost source is the current active source which is retransmitted further from output connections. Whichever source is active will be highlighted with a blinking background
Экрани асосӣ 3
The third screen displays format information on all detected streams Like Home Screen 2, the top-most source is the current active source which is retransmitted further from output connections. Whichever source is active will be highlighted with a blinking background
Менюи асосӣ
The Main Menu can be accessed by pressing the 
button and majority of options can be exited via the button Scroll with the button and confirm selection with the тугма.
Шарҳ: Not all menus will fit on the device screen so you will need to scroll to access some menus. The right side of most menu screens will will display a scroll bar which will help indicate the depth of scroll navigation
Генератори Timecode
The CodeBridge can generate clean, high output LTC out of the two isolated XLR3 ports (located on the rear of each unit)
-ро истифода баред button, then confirm selection with the button to cycle between the various generator options
- Format: Select between different industry standard FPS rates 23.976, 24, 25, 29.97ND, 29.97DF, and 30 FPS. If the selected format is compatible with MTC or Art-Net timecode, it will also be transmitted through that respective interface port (MIDI OUT or Ethernet ports)
- Start Time: Specify a start time of HH:MM:SS:FF using navigation buttons
- User Data: Specify user data in 0x00000000 hex format
- Play, Pause, Rewind: User playback controls for generated timecode.
Шарҳ: you must remain on this screen to continuously use the LTC generator. If you exit this screen, the generator will stop automatically, and the current source will change over to the next active source
Сатҳи баромад
Boost or cut the output level from +6 dBu to -12 dBu. Everything outputting via the two isolated XLR3 ports is affected by this level change.
Ин дар бар мегирад:
- Баромади генератор
- Re-transmitted timecode formats from other inputs
-ро истифода баредbutton, then confirm selection with the button to cycle between the various output levels. The asterisk indicator will denote the currently selected output level
Pre-roll Frames
- Pre-roll is the number of valid frames needed to consider the timecode source to be valid and begin forwarding it to the outputs
- Истифода баред
the button to highlight the Pre-roll value, then press button to edit - -ро истифода баред button to set the Pre-roll frames (1-30) and to save the value
Шарҳ: The active stream display will always show incoming LTC stream starting from the 1st received frame regardless of Pre-roll settings
Post-roll Frames
- Post-roll frames help correct erroneous or dropped frames in a timecode source
- When a stream is stopped for any reason, the transmission will continue until a count equivalent to the Post-roll frames setting is reached
- If an erratic source issue resolved within the Post-roll window, the device will continue streaming timecode without interruption
- Use the button to highlight the Post-roll value, then press button to edit. Use to select a value place in HH:MM:SS:FF format
- Press button to edit each value as needed, using or to change the count. Press after editing to save each value and repeat to edit the next.
Суроғаи IP
- View set the IP Address and Netmask of the unit
Note: This is the address used to access the CodeBridge Web Browser. This is mainly used to monitor and update each unit with future firmware releases - Use the button to highlight, then press button to edit either IP Address or Netmask
- Истифода баред to select a value in x.x.x.x format. Press to edit, using to change each value and again to save. Repeat to edit each octet
Номи дастгоҳ
Create a custom name for the device
Backspace
Change to UPPERCASE
Курсорро ҳаракат кунед- 123 Number editor
- – Add a space
- Истифода баред to select and highlight an editing tool or a letter, then press барои тасдиқи интихоб
- Highlight the 123 menu and press to input a numerical character.
- Истифода баред to select 0-9 and press again to confirm selection and type the character in the name field
- When name editing is complete, highlight OK and press наҷот додан ва баромадан
Маълумот дар бораи дастгоҳ
Device Info displays status information of the unit. The information displayed is:
- Номи дастгоҳ
- Суроғаи IP
- NetMask
- Суроғаи MAC
пахш кунед баромадан 
Маълумот дар бораи нармафзор
Firmware Info displays status information of the unit. The information displayed is
- Рақами версия
- Санаи сохтан
- Вақти сохтмон
пахш кунед баромадан
Харитаи меню
Нишондиҳандаҳои ҳолати LED
MIDl IN:
Receives timecode
Receives data which is not timecode
МИЁНА:
- Transmits timecode from source
Transmits timecode, postroll is running- Transmits data which is not timecode
LTC IN:
- Receives timecode, but 1 second has not passed without errors or jumps in timecode
- Receives timecode without jumps or errors for more than 1 second
Timecode was received, but is not received at the moment
LTC OUT:
- Transmits timecode, postroll is running
Transmits timecode, internal generator is running- Transmits timecode for more than 1 second
- Transmits timecode, but 1 second has not passed from start of transmission
WEB Браузер
Any networked computer can access the CodeBridge Web Браузер
Locate the IP address of the unit (instructions above) then type the IP address into the address bar of your favorite browser. You should be presented with the following landing page:
Note: computer or laptop should be in the same network range – 2.X.X.X
Навигариҳои нармафзор
Occasionally we will release firmware updates that contain new features or bug fixes. Firmware for all ProPlex units is available via the TMB Cloud
Истинод ба TMB Cloud дар зери менюи захираҳо дар мост webсайт https://tmb.com/
To update, download the new firmware.bin file to your desktop. Then upload through the “Firmware Upgrade” menu via the Web Браузер
ТОЗА ВА НИГАХДОРЙ
Dust build-up in connector ports can cause performance issues and can potentially lead to further damage during normal wear and tear CodeClock devices need occasional cleaning to maintain best performance, especially units used in harsher environmental conditions
THE FOLLOWING ARE GENERAL CLEANING GUIDELINES:
- Always disconnect from power before attempting any cleaning
- Wait until unit has cooled and discharged completely before cleaning
- Use vacuum or dry compressed air to remove dust/debris in and around connectors
- Use a soft towel or brush to wipe and buff the chassis body
- To clean the navigation screen, apply isopropyl alcohol with a soft lens cleaning tissue or lint free cotton
- Alcohol pads and q-tips may help remove any grime and residue from navigation buttons
МУҲИМ:
Be sure all surfaces are dry before attempting to power on again
ТЕХНИКИИ ТЕХНИКИ
| Рақами қисм | PPCODEBLME |
| Пайвасткунаки барқ | USB-C |
| Ethernet (& PoE in) Connector | Neutrik EtherCON™ RJ45 |
| MIDI Input Connector | DIN 5-Pin Female |
| MIDI Output Connector | DIN 5-Pin Female |
| LTC Input Connector | Neutrik™ Combination 3-Pin XLR and 1/4” TRS female |
| LTC Output Connectors | Neutrik™ 3-Pin XLR Male |
| Ҷилди амалиётӣtage | 5 VDC USB-C or 48 VDC PoE |
| Истеъмоли қувваи барқ | TBA |
| Ҳарорати корӣ. | TBA |
| Андозаҳо (HxWxD) | 1.72 x 7.22 x 4.42 дюйм [43.7 x 183.5 x 112.3 мм] |
| Вазн | 1.2 фунт [0.54 кг] |
| Вазни интиқол | 1.4 фунт [0.64 кг] |
МАЪЛУМОТ ДАР БОРАИ КАФОЛАТИ МАХДУД
Дастгоҳҳои паҳнкунии маълумотҳои ProPlex аз ҷониби TMB бар зидди маводҳои ноқис ё коркард дар тӯли ду (2) сол аз рӯзи фурӯши аслӣ аз ҷониби TMB кафолат дода мешавад. Кафолати TMB бо таъмир ё иваз кардани ҳама қисме, ки нуқсонаш собит мешавад ва то ба охир расидани мӯҳлатҳои кафолати мувофиқ ба TMB даъво пешниҳод шудааст, маҳдуд мешавад.
Ин Кафолати Маҳдуд эътибор надорад, агар камбудиҳои маҳсулот дар натиҷаи инҳо бошанд:
- Кушодани корпус, таъмир ё танзим аз ҷониби ягон каси ғайр аз TMB ё шахсони махсус аз ҷониби TMB ваколатдоршуда
- Садама, зӯроварии ҷисмонӣ, муносибати нодуруст ё нодуруст истифода бурдани маҳсулот.
- Зарари бар асари барқ, заминҷунбӣ, обхезӣ, терроризм, ҷанг ё амали Худо.
TMB will not assume responsibility for any labor expended, or materials used, to replace and/or repair the Product without TMB’s prior written authorization. Any repair of the Product in the field, and any associated labor charges, must be authorized in advance by TMB. Freight costs on warranty repairs are split 50/50: Customer pays to ship defective product to TMB; TMB pays to ship repaired product, ground freight, back to Customer. This warranty does not cover consequential damages or costs of any kind.
A Return Merchandise Authorization (RMA) Number must be obtained from TMB prior to return of any defective merchandise for warranty or non-warranty repair. For repair enquiries, please contact TMB via email at TechSupport@tmb.com ё ба яке аз маконҳои мо дар зер телефон кунед:
TMB ИМА
- Хиёбони 527.
- Сан Фернандо, CA 91340
- Штатхои Муттахида
- Тел: +1 818.899.8818
- TMB UK
- 21 Роҳи Армстронг
- Southall, UB2 4SD
Англия
- Тел: +44 (0)20.8574.9700
- You may also contact TMB directly via
- почтаи электронӣ дар TechSupport@tmb.com
ТАРТИБИ БОЗГАШТ
Лутфан бо TMB тамос гиред ва пеш аз интиқол додани ашё барои таъмир чиптаи таъмир ва рақами иҷозати баргардонидани молро дархост кунед. Омода бошед, ки рақами намунавӣ, рақами силсилавӣ ва тавсифи мухтасари сабаби бозгашт, инчунин суроғаи интиқоли бозгашт ва маълумоти тамосро пешниҳод кунед. Пас аз коркарди чиптаи таъмир, RMA # ва дастурҳои баргардонидан тавассути почтаи электронӣ ба мухотиб фиристода мешавад file.
Clearly label any shipping package(s) with ATTN: RMA#. Please return equipment prepaid and in the original packaging whenever possible. DO NOT include cables or accessories (unless advised otherwise). If original packaging is not available, be sure to properly pack and protect any equipment. TMB is not liable for any shipping damage resulting from inadequate packaging by the sender. Freight call tags will not be issued for shipping repairs to TMB, but TMB will pay the freight for return to the customer if the repair qualifies for warranty service. Non-warranty repairs will undergo a quotation process by the technician assigned to the repair. All associated costs for parts, labor and return shipping must be authorized in writing before any work can be completed. TMB reserves the right to use its own discretion to repair or replace product(s) and determine the warranty status of any equipment.
МАЪЛУМОТ БАРОИ ТАМОС
ШАРБ-КАРАРИ ЛОС-АНЧЕЛЕС
527 Парк хиёбони | Сан Фернандо, CA 91340, ИМА
- Тел: +1 818.899.8818
- Факс: + 1 818.899.8813 sales@tmb.com
- TMB 24/7 ДАСТГИРИИ ТЕХНИКӢ
- ИМА / Канада: +1.818.794.1286
- Ройгон: 1.877.862.3833 (1.877.TMB.DUDE)
- Британияи Кабир: +44 (0) 20.8574.9739
- Пардохти ройгон: 0800.652.5418 techsupport@tmb.com
- TMB 24/7 ДАСТГИРИИ ТЕХНИКӢ
ИМА / Канада: +1.818.794.1286
Ройгон: 1.877.862.3833 (1.877.TMB.DUDE) - Британияи Кабир: +44 (0) 20.8574.9739
- Пардохти ройгон: 0800.652.5418
- techsupport@tmb.com
Ширкати пурраи хидматрасонӣ, ки дастгирии техникӣ, хидматрасонии муштариён ва пайгирӣ мекунад.
Providing products and services for the industrial, entertainment, architectural, installation, defense, broadcast, research, telecommunications, and signage industries. Los Angeles, London, New York, Toronto, Riga and Beijing.
Effective 11 July 2025. © Copyright 2025, TMB. All rights reserved
Саволҳои зиёд такрормешуда
Q: Are spare screws available for the RackMount Kit?
A: Yes, spare screws are available from TMB if needed. Contact customer support for assistance with spare parts.
Ҳуҷҷатҳо / Сарчашмаҳо
 |
ProPlex CodeBridge TimeCode Or Midi Over Ethernet [pdf] Дастури корбар CodeBridge TimeCode Or Midi Over Ethernet, CodeBridge, TimeCode Or Midi Over Ethernet, Midi Over Ethernet, Over Ethernet, Ethernet |