MPD Series Automatic Backup Device
Tataiso ea ho Kena

BOHLOKOA POLOKETSO LITAELO

BOLOKANG LITAELO TSENA
You shall follow all the safety precautions mentioned in this manual when working on the device.
TLHOKOMELO
The product is designed and tested to strictly comply with related safety rules. Read and follow all the safety instructions and cautions before any operations. Improper operations might cause personal injury or property damage as the device is electrical equipment.
1.1 Hazard Level Definition
Maemo a fapaneng a melaetsa ea temoso bukeng ena a hlalosoa ka tsela e latelang:
KOTSI
E supa kotsi ea boemo bo holimo eo, ha e sa qojoe, e ka bakang lefu kapa kotsi e mpe.
TLHOKOMELO
E supa kotsi ea boemo bo mahareng, eo haeba e sa qojoe, e ka bakang lefu kapa kotsi e mpe.
TLHOKOMELO
E supa kotsi ea boemo bo tlase eo, haeba e sa qojoe, e ka bakang kotsi e nyane kapa e itekanetseng.
TSEBISO
Highlights key information and supplements other text. It may include skills and methods to solve product-related problems.
1.2 Tšireletseho Kakaretso
TSEBISO

• The information in this manual is subject to change due to product updates or other reasons. This guide cannot replace the product labels or other safety precautions unless otherwise specified. All descriptions here are for guidance only.
• Before installation, read through this manual to learn about the product and the precautions.
• Lits'ebetso tsohle li lokela ho etsoa ke litsebi tse koetlisitsoeng le tse nang le tsebo tse tsebang maemo a lehae le melaoana ea polokeho.
• Use insulating tools and wear personal protective equipment when operating the device to ensure personal safety. Wear anti-static gloves, cloths, and wrist strips when touching electronic devices to protect the device from damage.
• Strictly follow the installation, operation, and configuration instructions in this manual. The manufacturer shall not be liable for device damage or personal injury if you do not follow the instructions. Visit https://en.goodwe.com to get more information about product warranty.

1.3 Tšireletseho ea lisebelisoa
TLHOKOMELO
Voltage le khafetsa sebakeng sa ho hokela li lokela ho fihlela litlhoko tsa on-grid.
Make sure that the current rating of this product’s main breaker meets the specifications of the household power distribution unit.
The PE (equipment grounding) cable of the device must be connected firmly (1.6N·m).
For AC circuit connections, copper (CU) conductors are recommended.
KOTSI
All labels and warning marks should be visible after the installation. Do not scrawl on, damage, or cover any label on the device.
Unauthorized dismantling or modification may damage the equipment. Such action may damage the equipment and is not covered under the warranty. Warning labels on the device are as follows.

	KOTSI High voltage kotsi. Tlosa matla ohle a kenang 'me u tima sehlahisoa pele u sebetsa ho sona.
	Bala bukana ea mosebelisi pele u sebetsa sesebelisoa sena.
	Kotsi ea mocheso o phahameng. U se ke ua ama sehlahisoa se tlas'a ts'ebetso ho qoba ho chesoa.
	Do not dispose of the device as household waste. Discard the product in compliance with local laws and regulations, or send it back to the manufacturer.
	Ho lieha ho tsoa. Ema metsotso e 5 ka mor'a hore motlakase o tima ho fihlela likarolo li felile ka ho feletseng.
	Likotsi tse ka bang teng li teng. Apara PPE e nepahetseng pele o sebetsa.
	Sebaka sa motheo.
	SGS certification mark.

1.4 Litlhoko tsa Botho
TSEBISO

• Personnel who install or maintain the device must be strictly trained, learn about safety precautions and correct operations.
• Ke litsebi tse tšoanelehang feela kapa basebetsi ba koetlisitsoeng ba lumelloang ho kenya, ho sebetsa, ho hlokomela, le ho khutlisa sesebelisoa kapa likarolo.

Kenyelletso ea Sehlahisoa

2.1 Kenyelletso ea Sehlahisoa
Tlhaloso ea Mosebetsi
The device transfers between on-grid mode and backup mode with an integrated switch.
The device connects the main panel, the utility grid, and the AC output of the inverter to form an on-grid system when the utility grid works normally. Once the utility grid fails, the device will connect loads and the AC output of the inverter only to form a backup system.
The ABD supports one inverter and the MPD supports up to three inverters. Model Description
This manual covers listed device below:
ABD Series

• ABD200-40-US10
• ABD200-63-US10
• ABD100-40-US10
• ABD100-63-US10

Letoto la lihlooho tse MPD

• MPD200-40-US10
• MPD200-63-US10

Tlhaloso ea Mohlala

Che.	Tlhaloso	Tlhaloso
1	Sehlahisoa	ABD: Automatic Backup Device MPD: Multi-inverter Parallel Device
2	Main breaker rating	200: Applies to the main service panel whose main breaker rating is smaller than or equal to 200A and larger than 100A. 100: Applies to the main service panel whose main breaker rating is smaller than or equal to 100A.
3	Protection current of the inverter breaker	40/63: The protection current of the inverter breaker is 40A or 63A, which matches with the following inverters: Hybrid inverters: GW5000/6000/7600/9600/11K-ES-US20 AC-coupled inverters: GW5000/6000/7600/9600/11K-SBP-U520
4	Khoutu ea sebaka	US: the U.S.
5	Generation code	10: generation 1.0

Supported Grid Type
The inverter supports 120/240V split phase grid type.2.2 Maemo a Tšebeliso
Add an ABD (Automatic Backup Device) in the system to realize the whole home backup. Once the utility grid fails, the ABD will disconnect the main service panel from the utility grid, and the inverter will switch to off-grid working mode to supply power to the loads.
2.2.1 Application Scenarios – ABD
• Whole Home Backup System

Microgrid System2.2.2 Application Scenarios – MPD

2.3 Setšoantšo sa Motlakase
2.3.1 Electrical Diagram – ABD2.3.2 Electrical Diagram – MPD2.4 Ponahalo
Likarolo tse 2.4.1

Che.	Karolo	Tlhaloso
1	Letšoao la LED	Indicates the working status of the device.
2	Notlela	To lock the device’s door (key included).
3	Bracket e leketlileng	Hangs the device on the mounting support.
4	Smart meter	Contact after-sales service for support or replacement.
5	Insulation board	Ensures personal safety and protects the device.
6	Sekhechana sa motlakase	Provides overcurrent protection for the inverter. Recommended specifications: 40A or 63A (or 60A when the ALT of the installation site is less than 2000m) Breaker, UL489 certified. ABD: 1 x inverter breaker. MPD: 3 x inverter breakers. Sehlahisoa sa 'nete se ka fapana.
7	Sesenyi se ka Sehloohong	This breaker is optional when the main panel is also equipped with a breaker. Provides overcurrent protection from utility grid.

2.4.2 Litekanyo2.4.3 Lipontšo

Sesupo	Boemo	Tlhaloso
		ON= The grid is abnormal and the system is in Back-up mode.
		BLINK = The grid is normal and the system is in On-grid mode.
		OFF = With no input source, the system is in waiting mode.
		ON = The communication with the inverter is normal, and the 12V power supply from the inverter is normal.
		BLINK 1= The communication with the inverter is normal, and the 12V power supply from the inverter is abnormal.
		BLINK 2= The communication with the inverter is abnormal, and the 12V power supply from the inverter is normal.
		Off = The communication with the inverter is abnormal, and the 12V power supply from the inverter is abnormal.
		On = Fault has occurred.
		Off = No fault.

2.5 Tse fanoangTSEBISO

• N = Quantity depends on the device model.
• The number of pin terminals and communication terminal are various depending on different devices. The actual accessories may differ.
• The communication cable for parallel connection is only for MPD.

Ho kenya

3.1 Litlhoko tsa ho Instola
Litlhokahalo tsa Tikoloho ea ho kenyaTlhokahalo ea Angle ea ho kenya

3.2 Ho kenya sesebelisoa
TSEBISO

• Qoba lipeipi tsa metsi le likhoele tse patiloeng leboteng ha u phunya masoba.
• Apara likhalase le mask a lerōle ho thibela lerōle hore le se ke la hema kapa ho kopana le mahlo ha u phunya masoba.

Step 1 Put the mounting bracket on the wall or the support horizontally and mark positions for drilling holes.
Step 2 Drill holes to a depth of 80mm(3.15in) using the hammer drill. The diameter of the drill bit should be 10mm(0.39in).
Step 3 Secure the mounting bracket using the expansion bolts.
Step 4 Install the device on the mounting bracket.
Step 5 Screw to secure the device and the mounting bracket.

Khokahano ea Motlakase

4.1 Tlhokomelo ea Polokeho

KOTSI
DITAELO TSE MABAPI LE KOTSI YA MOLLO KAPA TŠITISO EA MOTLATSI

• Perform electrical connections, including operations, cables, and component specifications in compliance with local laws and regulations ANSI/NFPA 70.
• The input and output circuits are isolated from the enclosure and that system grounding, if required by the National Electric Code, ANSI/NFPA 70, is the responsibility of the installer.
• Power off the device before any electrical connections. Otherwise, an electric shock may occur.
• Tlama lithapo tsa mofuta o le mong hammoho, 'me u behelle likhoele tsa mefuta e fapaneng ka thōko. U se ke ua beha lithapo li tšoasehile kapa li tšetsoe.
• If the tension is too large, the cable may be poorly connected. You have to reserve a certain length of the cable before connecting it to the device cable port. • Make sure that the cable conductor is in full contact with the terminal and the cable insulation part is not crimped with the terminal when crimping the terminal. Otherwise, the device may not be able to work properly, or the connection may be unreliable during working, which may cause terminal block damage, etc.

TSEBISO

• Mebala ea lithapo tokomaneng ena ke ea litšupiso feela. Litlhaloso tsa cable li tla kopana le melao le melaoana ea lehae.

4.2 Preparing Conductor Conduit & Fittings
4.2.1 Conduit Holes
TLHOKOMELO

• Wiring conduits are additionally required, not included in the scope of delivery. The conduit must be UL514B listed and meet the specifications of the waterproof nut.
• To avoid influencing the protection class or damaging the equipment, check the wiring conduit to make sure that the conduit is installed properly and the holes are sealed.

Hole ea Conduit	Tlhaloso	Conduit
Grid ea AC	Install the wiring conduit and run Grid-L1, Grid-L2, and Neutral wire through the cable hole.	2 inch conduit
AC Meroalo	Install the wiring conduit and run Load-L1, Load-L2, Neutral wire, and PE through the cable hole.	2 inch conduit
Inverter	Install the wiring conduit and run Inverter-L1, Inverter-L2, Neutral wire, PE cable, and communication cable through the cable hole.	1 inch conduit

Litlhaloso tsa 4.2.2 tsa Wiring

Che.	Likarolo	Ho ngola	Tlhaloso
1.	Inverter communication terminal	Sesebelisoa sa motlakase COM	•    Terminal for connecting the communication cable of the inverter. •    Recommended specification: RJ45 cable, 24AWG, CAT5e or better.
2.	CT terminal for solar inverter	–	•    Terminal for connecting the CT for the solar inverter.
3.	CT	–	–
4.	Inverter terminal	Inverter A-L1 / L2, Inverter B-L1 / L2, Inverter C-L1 / L2, Inverter-N	•    Terminal for connecting the AC conductor of the inverter. •    Inverter B and Inverter C are only for MPD series products. •    Recommended specification: 6-8AWG, copper conductor, 90℃.
5.	AC Grid terminal	Grid-L1, Grid-L2, Grid-N	•    Terminal for connecting the Grid conductor. •    Recommended specification: •  4/0AWG, copper conductor, 90℃ for ABD200- 40-US10, ABD200-63-US10, MPD200-40-US10, and MPD200-63-US10. •  3AWG, copper conductor, 90℃ for ABD100-40- US10 and ABD100-63-US10.
6.	AC Loads terminal	Load-L1, Load-L2, Load-N	•    Terminal for connecting the AC conductor of the load. •    Recommended specification: •  4/0AWG, copper conductor, 90℃ for ABD200- 40-US10, ABD200-63-US10, MPD200-40-US10, and MPD200-63-US10. •  3AWG, copper conductor, 90℃ for ABD100-40- US10 and ABD100-63-US10.
7.	Sebaka sa busbar		•    Busbar for connecting the PE cable. •    Recommended specification: •  Load-PE: 4-6AWG, copper conductor, 90℃. •  Inverter-PE: 10AWG, copper conductor, 90℃.

4.3 Opening the Cabinet Door
Step 1 Unlock the cabinet door using the included key.
Step 2 Remove the six screws fixing the insulation board(torque: 0.8Nm).
Step 3 Remove the insulation board.4.4 Connecting the Conductors
TLHOKOMELO

• Connect the conductors to the right terminals like L1, L2, and N. The device may be damaged if the conductors are connected inappropriately.
• Make sure that the whole conductors are inserted into the terminal holes. No part of the conductor can be exposed.
• Make sure that the conductors are connected securely. Otherwise, the terminal may get too hot and damage the device.

4.4.1 Connecting the AC Conductors (Grid)
TLHOKOMELO
The ac output (neutral) is not bonded to ground.
Step 1 Strip the conductor wiring.
Step 2 Remove the waterproof cover using the included cap removal tool.
Step 3 Insert the desired conduit and corresponding adaptors, fittings, and bushings.
Step 4 Insert the conductors into the device and tighten the conduit.4.4.2 Connecting the AC Conductors (Load)
Step 1 Strip the conductor wiring.
Step 2 Remove the waterproof cover using the included cap removal tool.
Step 3 Insert the desired conduit and corresponding adaptors, fittings, and bushings.
Step 4 Insert the conductors into the device and tighten the conduit.4.4.3 Connecting the AC Conductors (Inverter)
Step 1 Strip the conductor wiring, crimp the conductor with appropriate wire connector.
Step 2 Remove the waterproof cover using the included cap removal tool.
Step 3 Insert the desired conduit and corresponding adaptors, fittings, and bushings.
Step 4 Insert the conductors into the device and tighten the conduit.4.4.4 Ho hokela Mohala oa Puisano
Step 1 Prepare a RJ45 network cable and insert it into the terminal.
Step 2 Run the cable through the cable clip and the conduit.4.4.5 Connecting the CT Cable (Optional)
TSEBISO

• Only for AC coupled inverters.

Mohato oa 1 Clamp the CT around the cable to be measured.
Step 2 Insert the CT cable into the terminal block.
Mofuta oa 1Mofuta oa 24.5 Closing the Cabinet Door
Step 1 Install the insulation board.
Step 2 Tighten the six screws fix the insulation board (torque: 0.8Nm).
Step 3 Optional. Lock up the device using the cabinet key. Keep the key properly for future use.

Thepa ea lisebelisoa

5.1 Sheba Pele O Bula

Che.	Hlahloba Ntho
1	The product is firmly installed at a clean place that is well-ventilated and easy-to- operate.
2	The PE, power, and communication cables are connected correctly and securely.
3	Maqhama a lithapo a tiile, a tsamaisoa ka tsela e nepahetseng le ka ho lekana.
4	Unused ports and terminals are fitted using the waterproof caps.
5	The insulation board is installed properly.
6	Voltage and frequency at the connection point meet the grid connection requirements.
7	Likoti tsa motlakase li koetsoe.

5.2 Power ON the Device
Step 1 Turn on the main breaker of the device.
Step 2 Turn on the inverter breaker of the device.

Tlhokomelo

6.1 Power OFF the Device
KOTSI
DITAELO TSE MABAPI LE KOTSI YA MOLLO KAPA TŠITISO EA MOTLATSI

• Power off the device before operations and maintenance. Otherwise, the device may be damaged or electric shocks may occur.
• Delayed discharge. Wait until the components are discharged and the LED indicators are off after power off.

Step 1 Turn off the main breaker of the device.
Step 2 Turn off the inverter breaker of the device.
Step 3 Turn off the breaker of the main panel.
Step 4 Power off the inverter.

6.2 Replacing the Inverter Breaker
TLHOKOMELO

• Make sure that the device is powered off.
• Wear proper personal protective equipment before any operations.

Step 1 Loosen the screws and cables of the breaker.
Step 2 Pull the plastic slot under the breaker.
Step 3 Replace the breaker with a new one, the new breaker shall be AC40A or 63A(60A) and UL489 certified.
Step 4 Place the breaker properly and push the plastic slot. Make sure that the breaker is securely installed.
Step 5 Tighten the cables.

Tekheniki Parameters

7.1 ABD Series Technical Parameters

Lintlha tsa Tekheniki	ABD200- 40-US10	ABD200- 63-US10	ABD100- 40-US10	ABD100- 63-US10
Lintlha tsa Motlakase
Ka lebitso Khumo Voltage (V)	240
Khumo VoltagE Range (V)	211-264
Feed-in Type	Phapang Phase
Nominal AC Voltage of Line Conductor (V)	120/240
Nominal AC Frequency (Hz)	60
AC Frequency Range (Hz)	58.5-61.2
Current Rating (From Grid)(A)	200
Max. Continuous Current From Inverter (A)	32	47.5	32	47.5
Maximum Overcurrent Protection of Main Breaker (A)*1	200		100
Maximum Overcurrent Protection of Circuit Breaker of Inverter (A)	40	63	40	63
Lintlha tse akaretsang
Operating Temperature Range (℉)	-13℉~+140℉ (-25℃~+60℃)*2
Max. Operating Altitude (ft)	9842ft (3000m)
Mokhoa oa ho Pholisa	Tlhahiso ea tlhaho
Puisano le Inverter	RS485
Boima ba 'mele (lb)	26lb (12kg)
Dimension (W×H×D in)	17.7×24×5.9 ho (450×610×150 mm)
Mounting Mount	Lebota le Kentsoeng
Tekanyo ea Tšireletso ea Ingress	Type 3R, IP44
Setifikeiti
Molao oa Tšireletso	UL1741, CSA 22.2 No. 107-01
EMC	FCC part15 CLASS B
*1: The main breaker is optional. *2: Derating temperature: 113℉(45℃).

7.2 MPD Series Technical Parameters

Lintlha tsa Tekheniki	MPD200-40-US10	MPD200-63-US10
Lintlha tsa Motlakase
Ka lebitso Khumo Voltage (V)	240
Khumo VoltagE Range (V)	211-264
Feed-in Type	Phapang Phase
Nominal AC Voltage of Line Conductor (V)	120/240
Nominal AC Frequency (Hz)	60
AC Frequency Range (Hz)	58.5-61.2
Current Rating (From Grid)(A)	200
Max. Continuous Current From Inverter (A)	32	47.5
Max. Amount of Inverters in Parallel	3
Maximum Overcurrent Protection of Main Breaker (A)*1	200
Maximum Overcurrent Protection of Circuit Breaker of Inverter (A)	40	63
Lintlha tse akaretsang
Operating Temperature Range (℉)	-13℉~+140℉ (-25℃~+60℃)*2
Max. Operating Altitude (ft)	9842ft (3000m)
Mokhoa oa ho Pholisa	Tlhahiso ea tlhaho
Puisano le Inverter	RS485
Boima ba 'mele (lb)	30lb (13.5kg)
Dimension (W×H×D in)	17.7×24×5.9 ho (450×610×150 mm)
Mounting Mount	Lebota le Kentsoeng
Tekanyo ea Tšireletso ea Ingress	Type 3R, IP44
Setifikeiti
Molao oa Tšireletso	UL1741, CSA 22.2 No. 107-01
EMC	FCC part15 CLASS B
*1: The main breaker is optional. *2: Derating temperature: 113℉(45℃).

https://en.goodwe.com/https://en.goodwe.com/contact-us.asp340-00797-04

GoodWe Technologies Co., Ltd.
No. 90 Zijin Rd., Setereke se Secha, Suzhou, 215011, Chaena
www.goodwe.com
service@goodwe.com

Litokomane / Lisebelisoa

GOODWE MPD Series Automatic Backup Device [pdf] Tlhophiso Tataiso ABD200-40-US10, ABD200-63-US10, ABD100-40-US10, ABD100-63-US10, MPD200-40-US10, MPD200-63-US10, MPD Series Automatic Backup Device, MPD Series, Automatic Backup Device, Backup Device

Litšupiso

• Bukana ea Mosebelisi