MPD Series Automatic Backup Device
ਇੰਸਟਾਲੇਸ਼ਨ ਗਾਈਡ
ਮਹੱਤਵਪੂਰਨ ਸੁਰੱਖਿਆ ਨਿਰਦੇਸ਼
ਇਹਨਾਂ ਹਦਾਇਤਾਂ ਨੂੰ ਸੁਰੱਖਿਅਤ ਕਰੋ
You shall follow all the safety precautions mentioned in this manual when working on the device.
ਚੇਤਾਵਨੀ
The product is designed and tested to strictly comply with related safety rules. Read and follow all the safety instructions and cautions before any operations. Improper operations might cause personal injury or property damage as the device is electrical equipment.
1.1 Hazard Level Definition
ਇਸ ਮੈਨੂਅਲ ਵਿੱਚ ਚੇਤਾਵਨੀ ਸੰਦੇਸ਼ਾਂ ਦੇ ਵੱਖ-ਵੱਖ ਪੱਧਰਾਂ ਨੂੰ ਇਸ ਤਰ੍ਹਾਂ ਪਰਿਭਾਸ਼ਿਤ ਕੀਤਾ ਗਿਆ ਹੈ:
ਖ਼ਤਰਾ
ਇੱਕ ਉੱਚ-ਪੱਧਰੀ ਖ਼ਤਰੇ ਨੂੰ ਦਰਸਾਉਂਦਾ ਹੈ, ਜੇਕਰ ਨਾ ਬਚਿਆ ਗਿਆ, ਤਾਂ ਮੌਤ ਜਾਂ ਗੰਭੀਰ ਸੱਟ ਲੱਗ ਸਕਦੀ ਹੈ।
ਚੇਤਾਵਨੀ
ਇੱਕ ਮੱਧਮ-ਪੱਧਰ ਦੇ ਖਤਰੇ ਨੂੰ ਦਰਸਾਉਂਦਾ ਹੈ, ਜੇਕਰ ਨਾ ਬਚਿਆ ਗਿਆ, ਤਾਂ ਮੌਤ ਜਾਂ ਗੰਭੀਰ ਸੱਟ ਲੱਗ ਸਕਦੀ ਹੈ।
ਸਾਵਧਾਨ
ਇੱਕ ਘੱਟ-ਪੱਧਰ ਦੇ ਖਤਰੇ ਨੂੰ ਦਰਸਾਉਂਦਾ ਹੈ, ਜੇਕਰ ਨਾ ਬਚਿਆ ਗਿਆ, ਤਾਂ ਮਾਮੂਲੀ ਜਾਂ ਦਰਮਿਆਨੀ ਸੱਟ ਲੱਗ ਸਕਦੀ ਹੈ।
ਨੋਟਿਸ
Highlights key information and supplements other text. It may include skills and methods to solve product-related problems.
1.2 ਆਮ ਸੁਰੱਖਿਆ
ਨੋਟਿਸ
- The information in this manual is subject to change due to product updates or other reasons. This guide cannot replace the product labels or other safety precautions unless otherwise specified. All descriptions here are for guidance only.
- Before installation, read through this manual to learn about the product and the precautions.
- ਸਾਰੇ ਓਪਰੇਸ਼ਨ ਸਿਖਲਾਈ ਪ੍ਰਾਪਤ ਅਤੇ ਜਾਣਕਾਰ ਤਕਨੀਸ਼ੀਅਨ ਦੁਆਰਾ ਕੀਤੇ ਜਾਣੇ ਚਾਹੀਦੇ ਹਨ ਜੋ ਸਥਾਨਕ ਮਿਆਰਾਂ ਅਤੇ ਸੁਰੱਖਿਆ ਨਿਯਮਾਂ ਤੋਂ ਜਾਣੂ ਹਨ।
- Use insulating tools and wear personal protective equipment when operating the device to ensure personal safety. Wear anti-static gloves, cloths, and wrist strips when touching electronic devices to protect the device from damage.
- Strictly follow the installation, operation, and configuration instructions in this manual. The manufacturer shall not be liable for device damage or personal injury if you do not follow the instructions. Visit https://en.goodwe.com to get more information about product warranty.
1.3 ਡਿਵਾਈਸ ਸੁਰੱਖਿਆ
ਚੇਤਾਵਨੀ
ਵਾਲੀਅਮtage ਅਤੇ ਕਨੈਕਟਿੰਗ ਪੁਆਇੰਟ 'ਤੇ ਬਾਰੰਬਾਰਤਾ ਨੂੰ ਆਨ-ਗਰਿੱਡ ਲੋੜਾਂ ਨੂੰ ਪੂਰਾ ਕਰਨਾ ਚਾਹੀਦਾ ਹੈ।
Make sure that the current rating of this product’s main breaker meets the specifications of the household power distribution unit.
The PE (equipment grounding) cable of the device must be connected firmly (1.6N·m).
For AC circuit connections, copper (CU) conductors are recommended.
ਖ਼ਤਰਾ
All labels and warning marks should be visible after the installation. Do not scrawl on, damage, or cover any label on the device.
Unauthorized dismantling or modification may damage the equipment. Such action may damage the equipment and is not covered under the warranty. Warning labels on the device are as follows.
 |
DANGER High Voltage ਖਤਰਾ। ਸਾਰੀ ਆਉਣ ਵਾਲੀ ਪਾਵਰ ਨੂੰ ਡਿਸਕਨੈਕਟ ਕਰੋ ਅਤੇ ਇਸ 'ਤੇ ਕੰਮ ਕਰਨ ਤੋਂ ਪਹਿਲਾਂ ਉਤਪਾਦ ਨੂੰ ਬੰਦ ਕਰੋ। |
 |
ਇਸ ਡਿਵਾਈਸ 'ਤੇ ਕੰਮ ਕਰਨ ਤੋਂ ਪਹਿਲਾਂ ਉਪਭੋਗਤਾ ਮੈਨੂਅਲ ਪੜ੍ਹੋ। |
 |
ਉੱਚ-ਤਾਪਮਾਨ ਦਾ ਖ਼ਤਰਾ। ਸੜਨ ਤੋਂ ਬਚਣ ਲਈ ਕਾਰਜ ਅਧੀਨ ਉਤਪਾਦ ਨੂੰ ਨਾ ਛੂਹੋ। |
 |
Do not dispose of the device as household waste. Discard the product in compliance with local laws and regulations, or send it back to the manufacturer. |
 |
ਦੇਰੀ ਨਾਲ ਡਿਸਚਾਰਜ. ਪਾਵਰ ਬੰਦ ਹੋਣ ਤੋਂ ਬਾਅਦ 5 ਮਿੰਟ ਇੰਤਜ਼ਾਰ ਕਰੋ ਜਦੋਂ ਤੱਕ ਕੰਪੋਨੈਂਟ ਪੂਰੀ ਤਰ੍ਹਾਂ ਡਿਸਚਾਰਜ ਨਹੀਂ ਹੋ ਜਾਂਦੇ। |
 |
ਸੰਭਾਵੀ ਖਤਰੇ ਮੌਜੂਦ ਹਨ। ਕਿਸੇ ਵੀ ਓਪਰੇਸ਼ਨ ਤੋਂ ਪਹਿਲਾਂ ਸਹੀ PPE ਪਹਿਨੋ। |
 |
ਜ਼ਮੀਨੀ ਬਿੰਦੂ। |
 |
SGS certification mark. |
1.4 ਨਿੱਜੀ ਲੋੜਾਂ
ਨੋਟਿਸ
- Personnel who install or maintain the device must be strictly trained, learn about safety precautions and correct operations.
- ਸਿਰਫ਼ ਯੋਗ ਪੇਸ਼ੇਵਰਾਂ ਜਾਂ ਸਿਖਿਅਤ ਕਰਮਚਾਰੀਆਂ ਨੂੰ ਡਿਵਾਈਸ ਜਾਂ ਪਾਰਟਸ ਨੂੰ ਸਥਾਪਤ ਕਰਨ, ਚਲਾਉਣ, ਰੱਖ-ਰਖਾਅ ਕਰਨ ਅਤੇ ਬਦਲਣ ਦੀ ਇਜਾਜ਼ਤ ਹੈ।
ਉਤਪਾਦ ਦੀ ਜਾਣ-ਪਛਾਣ
2.1 ਉਤਪਾਦ ਦੀ ਜਾਣ-ਪਛਾਣ
ਫੰਕਸ਼ਨ ਵੇਰਵਾ
The device transfers between on-grid mode and backup mode with an integrated switch.
The device connects the main panel, the utility grid, and the AC output of the inverter to form an on-grid system when the utility grid works normally. Once the utility grid fails, the device will connect loads and the AC output of the inverter only to form a backup system.
The ABD supports one inverter and the MPD supports up to three inverters. Model Description
This manual covers listed device below:
ABD Series
- ABD200-40-US10
- ABD200-63-US10
- ABD100-40-US10
- ABD100-63-US10
MPD ਸੀਰੀਜ਼
- MPD200-40-US10
- MPD200-63-US10
ਮਾਡਲ ਵਿਆਖਿਆ
| ਨੰ. | ਭਾਵ | ਵਰਣਨ |
| 1 | ਉਤਪਾਦ | ABD: Automatic Backup Device MPD: Multi-inverter Parallel Device |
| 2 | Main breaker rating | 200: Applies to the main service panel whose main breaker rating is smaller than or equal to 200A and larger than 100A. 100: Applies to the main service panel whose main breaker rating is smaller than or equal to 100A. |
| 3 | Protection current of the inverter breaker | 40/63: The protection current of the inverter breaker is 40A or 63A, which matches with the following inverters: Hybrid inverters: GW5000/6000/7600/9600/11K-ES-US20 AC-coupled inverters: GW5000/6000/7600/9600/11K-SBP-U520 |
| 4 | ਖੇਤਰ ਕੋਡ | US: the U.S. |
| 5 | Generation code | 10: generation 1.0 |
Supported Grid Type
The inverter supports 120/240V split phase grid type.
2.2 ਐਪਲੀਕੇਸ਼ਨ ਦ੍ਰਿਸ਼
Add an ABD (Automatic Backup Device) in the system to realize the whole home backup. Once the utility grid fails, the ABD will disconnect the main service panel from the utility grid, and the inverter will switch to off-grid working mode to supply power to the loads.
2.2.1 Application Scenarios – ABD
• Whole Home Backup System
Microgrid System
2.2.2 Application Scenarios – MPD
2.3 ਇਲੈਕਟ੍ਰੀਕਲ ਡਾਇਗ੍ਰਾਮ
2.3.1 Electrical Diagram – ABD
2.3.2 Electrical Diagram – MPD
੨ਰੂਪ
2.4.1 ਹਿੱਸੇ
| ਨੰ. | ਭਾਗ | ਵਰਣਨ |
| 1 | LED ਸੂਚਕ | Indicates the working status of the device. |
| 2 | ਤਾਲਾ | To lock the device’s door (key included). |
| 3 | ਹੈਂਗਿੰਗ ਬਰੈਕਟ | Hangs the device on the mounting support. |
| 4 | ਸਮਾਰਟ ਮੀਟਰ | Contact after-sales service for support or replacement. |
| 5 | ਇਨਸੂਲੇਸ਼ਨ ਬੋਰਡ | Ensures personal safety and protects the device. |
| 6 | ਇਨਵਰਟਰ ਤੋੜਨ ਵਾਲਾ | Provides overcurrent protection for the inverter. Recommended specifications: 40A or 63A (or 60A when the ALT of the installation site is less than 2000m) Breaker, UL489 certified. ABD: 1 x inverter breaker. MPD: 3 x inverter breakers. ਅਸਲ ਉਤਪਾਦ ਵੱਖ-ਵੱਖ ਹੋ ਸਕਦਾ ਹੈ। |
| 7 | ਮੁੱਖ ਤੋੜਨ ਵਾਲਾ | This breaker is optional when the main panel is also equipped with a breaker. Provides overcurrent protection from utility grid. |
2.4.2 ਮਾਪ
2.4.3 ਸੂਚਕ
| ਸੂਚਕ | ਸਥਿਤੀ | ਵਿਆਖਿਆ |
 |
 |
ON= The grid is abnormal and the system is in Back-up mode. |
 |
BLINK = The grid is normal and the system is in On-grid mode. | |
 |
OFF = With no input source, the system is in waiting mode. | |
 |
 |
ON = The communication with the inverter is normal, and the 12V power supply from the inverter is normal. |
 |
BLINK 1= The communication with the inverter is normal, and the 12V power supply from the inverter is abnormal. | |
 |
BLINK 2= The communication with the inverter is abnormal, and the 12V power supply from the inverter is normal. | |
|
Off = The communication with the inverter is abnormal, and the 12V power supply from the inverter is abnormal. | |
 |
 |
On = Fault has occurred. |
|
Off = No fault. |
2.5 ਡਿਲੀਵਰੇਬਲ
ਨੋਟਿਸ
- N = Quantity depends on the device model.
- The number of pin terminals and communication terminal are various depending on different devices. The actual accessories may differ.
- The communication cable for parallel connection is only for MPD.
ਇੰਸਟਾਲੇਸ਼ਨ
3.1 ਇੰਸਟਾਲੇਸ਼ਨ ਦੀਆਂ ਲੋੜਾਂ
ਇੰਸਟਾਲੇਸ਼ਨ ਵਾਤਾਵਰਣ ਲੋੜ
ਇੰਸਟਾਲੇਸ਼ਨ ਕੋਣ ਲੋੜ
3.2 ਡਿਵਾਈਸ ਇੰਸਟਾਲੇਸ਼ਨ
ਨੋਟਿਸ
- ਛੇਕ ਡ੍ਰਿਲ ਕਰਦੇ ਸਮੇਂ ਕੰਧ ਵਿੱਚ ਦੱਬੀਆਂ ਪਾਣੀ ਦੀਆਂ ਪਾਈਪਾਂ ਅਤੇ ਕੇਬਲਾਂ ਤੋਂ ਬਚੋ।
- ਮੋਰੀਆਂ ਨੂੰ ਡ੍ਰਿਲ ਕਰਦੇ ਸਮੇਂ ਧੂੜ ਨੂੰ ਸਾਹ ਲੈਣ ਜਾਂ ਅੱਖਾਂ ਨਾਲ ਸੰਪਰਕ ਕਰਨ ਤੋਂ ਰੋਕਣ ਲਈ ਚਸ਼ਮਾ ਅਤੇ ਧੂੜ ਦਾ ਮਾਸਕ ਪਹਿਨੋ।
Step 1 Put the mounting bracket on the wall or the support horizontally and mark positions for drilling holes.
Step 2 Drill holes to a depth of 80mm(3.15in) using the hammer drill. The diameter of the drill bit should be 10mm(0.39in).
Step 3 Secure the mounting bracket using the expansion bolts.
Step 4 Install the device on the mounting bracket.
Step 5 Screw to secure the device and the mounting bracket.
ਇਲੈਕਟ੍ਰੀਕਲ ਕੁਨੈਕਸ਼ਨ
4.1 ਸੁਰੱਖਿਆ ਸਾਵਧਾਨੀ
ਖ਼ਤਰਾ
ਅੱਗ ਜਾਂ ਬਿਜਲੀ ਦੇ ਝਟਕੇ ਦੇ ਜੋਖਮ ਨਾਲ ਸਬੰਧਤ ਹਦਾਇਤਾਂ
- Perform electrical connections, including operations, cables, and component specifications in compliance with local laws and regulations ANSI/NFPA 70.
- The input and output circuits are isolated from the enclosure and that system grounding, if required by the National Electric Code, ANSI/NFPA 70, is the responsibility of the installer.
- Power off the device before any electrical connections. Otherwise, an electric shock may occur.
- ਇੱਕੋ ਕਿਸਮ ਦੀਆਂ ਕੇਬਲਾਂ ਨੂੰ ਇਕੱਠੇ ਬੰਨ੍ਹੋ, ਅਤੇ ਵੱਖ-ਵੱਖ ਕਿਸਮਾਂ ਦੀਆਂ ਕੇਬਲਾਂ ਨੂੰ ਅਲੱਗ ਰੱਖੋ। ਕੇਬਲਾਂ ਨੂੰ ਉਲਝਿਆ ਜਾਂ ਪਾਰ ਨਾ ਕਰੋ।
- If the tension is too large, the cable may be poorly connected. You have to reserve a certain length of the cable before connecting it to the device cable port. • Make sure that the cable conductor is in full contact with the terminal and the cable insulation part is not crimped with the terminal when crimping the terminal. Otherwise, the device may not be able to work properly, or the connection may be unreliable during working, which may cause terminal block damage, etc.
ਨੋਟਿਸ
- ਇਸ ਦਸਤਾਵੇਜ਼ ਵਿੱਚ ਕੇਬਲ ਰੰਗ ਸਿਰਫ਼ ਸੰਦਰਭ ਲਈ ਹਨ। ਕੇਬਲ ਵਿਸ਼ੇਸ਼ਤਾਵਾਂ ਸਥਾਨਕ ਕਾਨੂੰਨਾਂ ਅਤੇ ਨਿਯਮਾਂ ਨੂੰ ਪੂਰਾ ਕਰਨਗੀਆਂ।
4.2 Preparing Conductor Conduit & Fittings
4.2.1 Conduit Holes
ਚੇਤਾਵਨੀ
- Wiring conduits are additionally required, not included in the scope of delivery. The conduit must be UL514B listed and meet the specifications of the waterproof nut.
- To avoid influencing the protection class or damaging the equipment, check the wiring conduit to make sure that the conduit is installed properly and the holes are sealed.
| ਨਾਲੀ ਦਾ ਛੇਕ | ਵਰਣਨ | ਨਦੀ |
| AC ਗਰਿੱਡ | Install the wiring conduit and run Grid-L1, Grid-L2, and Neutral wire through the cable hole. | 2 inch conduit |
| AC ਲੋਡ | Install the wiring conduit and run Load-L1, Load-L2, Neutral wire, and PE through the cable hole. | 2 inch conduit |
| ਇਨਵਰਟਰ | Install the wiring conduit and run Inverter-L1, Inverter-L2, Neutral wire, PE cable, and communication cable through the cable hole. |
1 inch conduit |
4.2.2 ਵਾਇਰਿੰਗ ਨਿਰਧਾਰਨ
| ਨੰ. | ਹਿੱਸੇ | ਲੇਬਲਿੰਗ | ਵਰਣਨ |
| 1. | Inverter communication terminal | ਇਨਵਰਟਰ COM | • Terminal for connecting the communication cable of the inverter. • Recommended specification: RJ45 cable, 24AWG, CAT5e or better. |
| 2. | CT terminal for solar inverter | – | • Terminal for connecting the CT for the solar inverter. |
| 3. | CT | – | – |
| 4. | ਇਨਵਰਟਰ ਟਰਮੀਨਲ | Inverter A-L1 / L2, Inverter B-L1 / L2, Inverter C-L1 / L2, Inverter-N | • Terminal for connecting the AC conductor of the inverter. • Inverter B and Inverter C are only for MPD series products. • Recommended specification: 6-8AWG, copper conductor, 90℃. |
| 5. | AC Grid terminal | Grid-L1, Grid-L2, Grid-N | • Terminal for connecting the Grid conductor. • Recommended specification: • 4/0AWG, copper conductor, 90℃ for ABD200- 40-US10, ABD200-63-US10, MPD200-40-US10, and MPD200-63-US10. • 3AWG, copper conductor, 90℃ for ABD100-40- US10 and ABD100-63-US10. |
| 6. | AC Loads terminal | Load-L1, Load-L2, Load-N | • Terminal for connecting the AC conductor of the load. • Recommended specification: • 4/0AWG, copper conductor, 90℃ for ABD200- 40-US10, ABD200-63-US10, MPD200-40-US10, and MPD200-63-US10. • 3AWG, copper conductor, 90℃ for ABD100-40- US10 and ABD100-63-US10. |
| 7. | ਗਰਾਊਂਡਿੰਗ ਬੱਸਬਾਰ | • Busbar for connecting the PE cable. • Recommended specification: • Load-PE: 4-6AWG, copper conductor, 90℃. • Inverter-PE: 10AWG, copper conductor, 90℃. |
4.3 Opening the Cabinet Door
Step 1 Unlock the cabinet door using the included key.
Step 2 Remove the six screws fixing the insulation board(torque: 0.8Nm).
Step 3 Remove the insulation board.
4.4 Connecting the Conductors
ਚੇਤਾਵਨੀ
- Connect the conductors to the right terminals like L1, L2, and N. The device may be damaged if the conductors are connected inappropriately.
- Make sure that the whole conductors are inserted into the terminal holes. No part of the conductor can be exposed.
- Make sure that the conductors are connected securely. Otherwise, the terminal may get too hot and damage the device.
4.4.1 Connecting the AC Conductors (Grid)
ਚੇਤਾਵਨੀ
The ac output (neutral) is not bonded to ground.
Step 1 Strip the conductor wiring.
Step 2 Remove the waterproof cover using the included cap removal tool.
Step 3 Insert the desired conduit and corresponding adaptors, fittings, and bushings.
Step 4 Insert the conductors into the device and tighten the conduit.
4.4.2 Connecting the AC Conductors (Load)
Step 1 Strip the conductor wiring.
Step 2 Remove the waterproof cover using the included cap removal tool.
Step 3 Insert the desired conduit and corresponding adaptors, fittings, and bushings.
Step 4 Insert the conductors into the device and tighten the conduit.
4.4.3 Connecting the AC Conductors (Inverter)
Step 1 Strip the conductor wiring, crimp the conductor with appropriate wire connector.
Step 2 Remove the waterproof cover using the included cap removal tool.
Step 3 Insert the desired conduit and corresponding adaptors, fittings, and bushings.
Step 4 Insert the conductors into the device and tighten the conduit.
4.4.4 ਸੰਚਾਰ ਕੇਬਲ ਨੂੰ ਜੋੜਨਾ
Step 1 Prepare a RJ45 network cable and insert it into the terminal.
Step 2 Run the cable through the cable clip and the conduit.
4.4.5 Connecting the CT Cable (Optional)
ਨੋਟਿਸ
- Only for AC coupled inverters.
ਕਦਮ 1 Clamp the CT around the cable to be measured.
Step 2 Insert the CT cable into the terminal block.
ਟਾਈਪ 1
ਟਾਈਪ 2
4.5 Closing the Cabinet Door
Step 1 Install the insulation board.
Step 2 Tighten the six screws fix the insulation board (torque: 0.8Nm).
Step 3 Optional. Lock up the device using the cabinet key. Keep the key properly for future use.
ਉਪਕਰਣ ਕਮਿਸ਼ਨਿੰਗ
5.1 ਪਾਵਰ ਚਾਲੂ ਹੋਣ ਤੋਂ ਪਹਿਲਾਂ ਜਾਂਚ ਕਰੋ
| ਨੰ. | ਆਈਟਮ ਦੀ ਜਾਂਚ ਕਰੋ |
| 1 | The product is firmly installed at a clean place that is well-ventilated and easy-to- operate. |
| 2 | The PE, power, and communication cables are connected correctly and securely. |
| 3 | ਕੇਬਲ ਸਬੰਧ ਬਰਕਰਾਰ ਹਨ, ਸਹੀ ਢੰਗ ਨਾਲ ਅਤੇ ਸਮਾਨ ਰੂਪ ਵਿੱਚ ਰੂਟ ਕੀਤੇ ਗਏ ਹਨ। |
| 4 | Unused ports and terminals are fitted using the waterproof caps. |
| 5 | The insulation board is installed properly. |
| 6 | ਵਾਲੀਅਮtage and frequency at the connection point meet the grid connection requirements. |
| 7 | ਬਿਜਲਈ ਕੰਡਿਊਟ ਹੋਲ ਸੀਲ ਕੀਤੇ ਜਾਂਦੇ ਹਨ। |
5.2 Power ON the Device
Step 1 Turn on the main breaker of the device.
Step 2 Turn on the inverter breaker of the device.
ਰੱਖ-ਰਖਾਅ
6.1 Power OFF the Device
ਖ਼ਤਰਾ
ਅੱਗ ਜਾਂ ਬਿਜਲੀ ਦੇ ਝਟਕੇ ਦੇ ਜੋਖਮ ਨਾਲ ਸਬੰਧਤ ਹਦਾਇਤਾਂ
- Power off the device before operations and maintenance. Otherwise, the device may be damaged or electric shocks may occur.
- Delayed discharge. Wait until the components are discharged and the LED indicators are off after power off.
Step 1 Turn off the main breaker of the device.
Step 2 Turn off the inverter breaker of the device.
Step 3 Turn off the breaker of the main panel.
Step 4 Power off the inverter.
6.2 Replacing the Inverter Breaker
ਚੇਤਾਵਨੀ
- Make sure that the device is powered off.
- Wear proper personal protective equipment before any operations.
Step 1 Loosen the screws and cables of the breaker.
Step 2 Pull the plastic slot under the breaker.
Step 3 Replace the breaker with a new one, the new breaker shall be AC40A or 63A(60A) and UL489 certified.
Step 4 Place the breaker properly and push the plastic slot. Make sure that the breaker is securely installed.
Step 5 Tighten the cables.
ਤਕਨੀਕੀ ਮਾਪਦੰਡ
7.1 ABD Series Technical Parameters
| ਤਕਨੀਕੀ ਡਾਟਾ | ABD200- 40-US10 | ABD200- 63-US10 | ABD100- 40-US10 | ABD100- 63-US10 |
| ਇਲੈਕਟ੍ਰੀਕਲ ਡਾਟਾ | ||||
| ਨਾਮਾਤਰ ਆਉਟਪੁੱਟ ਵਾਲੀਅਮtagਈ (ਵੀ) | 240 | |||
| ਆਉਟਪੁੱਟ ਵਾਲੀਅਮtage ਰੇਂਜ (V) | 211~264 | |||
| Feed-in Type | ਵੰਡੋ ਪੜਾਅ | |||
| ਨਾਮਾਤਰ AC ਵੋਲtage of Line Conductor (V) | 120/240 | |||
| ਨਾਮਾਤਰ AC ਫ੍ਰੀਕੁਐਂਸੀ (Hz) | 60 | |||
| AC Frequency Range (Hz) | 58.5~61.2 | |||
| Current Rating (From Grid)(A) | 200 | |||
| Max. Continuous Current From Inverter (A) | 32 | 47.5 | 32 | 47.5 |
| Maximum Overcurrent Protection of Main Breaker (A)*1 | 200 | 100 | ||
| Maximum Overcurrent Protection of Circuit Breaker of Inverter (A) | 40 | 63 | 40 | 63 |
| ਆਮ ਡਾਟਾ | ||||
| Operating Temperature Range (℉) | -13℉~+140℉ (-25℃~+60℃)*2 | |||
| Max. Operating Altitude (ft) | 9842 ਫੁੱਟ (3000 ਮੀਟਰ) | |||
| ਕੂਲਿੰਗ ਵਿਧੀ | ਕੁਦਰਤੀ ਪਹੁੰਚ | |||
| ਇਨਵਰਟਰ ਨਾਲ ਸੰਚਾਰ | RS485 | |||
| ਵਜ਼ਨ (lb) | 26lb (12kg) | |||
| Dimension (W×H×D in) | 17.7×24×5.9 ਇੰਚ (450×610×150 ਮਿਲੀਮੀਟਰ) | |||
| ਮਾਊਂਟਿੰਗ ਵਿਧੀ | ਕੰਧ ਮਾਊਟ | |||
| ਪ੍ਰਵੇਸ਼ ਸੁਰੱਖਿਆ ਰੇਟਿੰਗ | Type 3R, IP44 | |||
| ਸਰਟੀਫਿਕੇਸ਼ਨ | ||||
| ਸੁਰੱਖਿਆ ਨਿਯਮ | UL1741, CSA 22.2 No. 107-01 | |||
| ਈ.ਐਮ.ਸੀ | FCC part15 CLASS B | |||
| *1: The main breaker is optional. *2: Derating temperature: 113℉(45℃). |
||||
7.2 MPD Series Technical Parameters
| ਤਕਨੀਕੀ ਡਾਟਾ | MPD200-40-US10 | MPD200-63-US10 |
| ਇਲੈਕਟ੍ਰੀਕਲ ਡਾਟਾ | ||
| ਨਾਮਾਤਰ ਆਉਟਪੁੱਟ ਵਾਲੀਅਮtagਈ (ਵੀ) | 240 | |
| ਆਉਟਪੁੱਟ ਵਾਲੀਅਮtage ਰੇਂਜ (V) | 211~264 | |
| Feed-in Type | ਵੰਡੋ ਪੜਾਅ | |
| ਨਾਮਾਤਰ AC ਵੋਲtage of Line Conductor (V) | 120/240 | |
| ਨਾਮਾਤਰ AC ਫ੍ਰੀਕੁਐਂਸੀ (Hz) | 60 | |
| AC Frequency Range (Hz) | 58.5~61.2 | |
| Current Rating (From Grid)(A) | 200 | |
| Max. Continuous Current From Inverter (A) | 32 | 47.5 |
| Max. Amount of Inverters in Parallel | 3 | |
| Maximum Overcurrent Protection of Main Breaker (A)*1 | 200 | |
| Maximum Overcurrent Protection of Circuit Breaker of Inverter (A) | 40 | 63 |
| ਆਮ ਡਾਟਾ | ||
| Operating Temperature Range (℉) | -13℉~+140℉ (-25℃~+60℃)*2 | |
| Max. Operating Altitude (ft) | 9842 ਫੁੱਟ (3000 ਮੀਟਰ) | |
| ਕੂਲਿੰਗ ਵਿਧੀ | ਕੁਦਰਤੀ ਪਹੁੰਚ | |
| ਇਨਵਰਟਰ ਨਾਲ ਸੰਚਾਰ | RS485 | |
| ਵਜ਼ਨ (lb) | 30lb (13.5kg) | |
| Dimension (W×H×D in) | 17.7×24×5.9 ਇੰਚ (450×610×150 ਮਿਲੀਮੀਟਰ) | |
| ਮਾਊਂਟਿੰਗ ਵਿਧੀ | ਕੰਧ ਮਾਊਟ | |
| ਪ੍ਰਵੇਸ਼ ਸੁਰੱਖਿਆ ਰੇਟਿੰਗ | Type 3R, IP44 | |
| ਸਰਟੀਫਿਕੇਸ਼ਨ | ||
| ਸੁਰੱਖਿਆ ਨਿਯਮ | UL1741, CSA 22.2 No. 107-01 | |
| ਈ.ਐਮ.ਸੀ | FCC part15 CLASS B | |
| *1: The main breaker is optional. *2: Derating temperature: 113℉(45℃). |
||
https://en.goodwe.com/
https://en.goodwe.com/contact-us.asp
340-00797-04
ਗੁੱਡਵੇ ਟੈਕਨੋਲੋਜੀਸ ਕੰ., ਲਿਮਿਟੇਡ
ਨੰਬਰ 90 ਜ਼ੀਜਿਨ ਰੋਡ, ਨਵਾਂ ਜ਼ਿਲ੍ਹਾ, ਸੂਜ਼ੌ, 215011, ਚੀਨ
www.goodwe.com
service@goodwe.com
ਦਸਤਾਵੇਜ਼ / ਸਰੋਤ
 |
GOODWE MPD Series Automatic Backup Device [pdf] ਇੰਸਟਾਲੇਸ਼ਨ ਗਾਈਡ ABD200-40-US10, ABD200-63-US10, ABD100-40-US10, ABD100-63-US10, MPD200-40-US10, MPD200-63-US10, MPD Series Automatic Backup Device, MPD Series, Automatic Backup Device, Backup Device |