ST01/ST01K/EI600
In-Wall Timer yokhala ndi Astro kapena Countdown Feature
Kukhazikitsa ndi Wogwiritsa Ntchito
Libertyville, Illinois 60048
www.intermatic.com

MATENDA

		Chithunzi cha ST01/ST01K	EI600
Opaleshoni Voltage		120-277 VAC, 50/60 Hz
Wotsutsa (heater) I		15 A' 120-277VAC	20 A,120-277 VAC
Tungsten (chithunzi)		115A,120 VAC; 6 A, 208-277 VAC
Ballast (fuloresenti) 1		8 A,120 VAC; 4A, 208-277 VAC	16 A,120-277 VAC
Electronic Ballast (LED)	5 A 120 VAC; 2 A277 VAC
Load Rating I (Motor)		1 HR 120 VAC; 2 HR 240 VAC
DC Loads I		4 A, 12 VDC; 2 A, 28 VDC
Kutentha kwa Ntchito		132° F mpaka 104° F (0° C mpaka 40° C)
Makulidwe i		4 1/8″ H x 1 3/4″ W x 1 1316″ D
Kusalowerera Ndale Sikofunikira

GAWO LACHITETEZO

CHENJEZO
Kuopsa kwa Moto kapena Kugwedezeka kwa Magetsi

• Chotsani magetsi pa chophwanyira dera kapena chotsani ma switch (ma) musanayike kapena kugwiritsa ntchito (kuphatikiza kusintha batire).
• Kuyika ndi/kapena mawaya kuyenera kutsata malamulo amagetsi adziko lonse komanso amdera lanu.
• Gwiritsani ntchito makondakitala a COPPER POKHA.
• Osawonjezeranso, kugawa, kutentha pamwamba pa 212 ° F (100 ° C), kuphwanya, kapena kuyatsa batri ya Lithium. Khalani kutali ndi ana.
• Sinthani batire ndi Type CR2 yokha yomwe imatsimikiziridwa ndi
  Underwriters Laboratories (UL).
• OSAGWIRITSA NTCHITO chowerengera nthawi kuwongolera zida zomwe zitha kukhala zowopsa chifukwa chanthawi yolakwika, monga: sun lamps, saunas, heaters, ophika pang'onopang'ono, etc.

CHIDZIWITSO

• Tsatirani ma code amagetsi apafupi poika.
• Chiwopsezo cha kuwonongeka kwa nthawi chifukwa chakutayikira ngati batire yofooka sisinthidwa mwachangu.
• Tayani katundu malinga ndi malamulo akumaloko otaya mabatire a Lithiamu.

TIMER INTERFACE

MAFOTOKOZEDWE AKATUNDU

Makina owerengera a ST01 ndi EI600 amaphatikiza ndandanda, ndi zowerengera kukhala gawo limodzi losavuta kukhazikitsa. Zomwe zili ndi mapulogalamu amasiku 7 okhala ndi kusintha kosankha kwa Automatic Daylight Saving Time (DST), malo 40 omwe amapezeka kuti amange zochitika zilizonse zomwe zakonzedwa (Mbandakucha, Madzulo kapena Nthawi Zina), mawonekedwe a RAND (mwachisawawa) omwe amagwiritsidwa ntchito kuletsa alendo osafunikira, “otanganidwa” kuyang'ana pamene inu muli kutali, ndi zina. Ntchito ya PASI (kuwerengera) idapangidwa kuti izizimitsa zida zitatha kuyambitsa, kuyambira sekondi imodzi mpaka maola 24, ndipo ndi incandescent, fulorosenti, CFL ndi LED zimagwirizana. ST01/EI600 imatha kuthana ndi mitundu yambiri ya katundu, safuna kulumikizidwa kwa waya osalowerera, ndipo imathandizira zilankhulo zitatu, Chingerezi (ENG), Chisipanishi (SPAN), ndi Chifalansa (FRN), ndikupangitsa kuti ikhale yabwino pamapulogalamu ambiri.

MFUNDO ZOFUNIKA

Chonde werengani zolembazi musanapitirize.

• Chowerengeracho chimakhala ndi batri ndipo sichifuna mphamvu ya AC kuti chikhazikitse ndi kukonza mapulogalamu; imayang'aniranso ntchito ya ON / OFF ("kudina" phokoso) ndikusunga nthawi ndi tsiku.
• BATT LOW imawunikira pachiwonetsero pamene mphamvu ya batri ili yochepa.
• Mukasintha batire, choyamba chotsani mphamvu ya AC.
  Batire yakale ikachotsedwa, mudzakhala ndi mphindi zingapo kuti muyike batire yatsopano tsiku ndi nthawi zisanatayike. Zokonda zina zonse zikhalabe m'makumbukidwe, opanda batire kapena mphamvu ya AC.
• Mitundu ya AUTO (yokha) ndi RAND (mwachisawawa) sizimawonekera pazosankha mpaka chochitika chimodzi ON kapena WOZIMUTSA chitsatidwe.
• Mindandanda yonse "loop" (bwerezani zosankha kumapeto kwa menyu). Mukakhala mu MENU inayake, dinani ON/OFF kuti mulowe mu MENU imeneyo.
• Mabatani a + kapena - amasintha zomwe zikuwunikira pazenera.
  Gwirani pansi kuti muyende mwachangu.
• Ntchito yowerengera (PASI) imalola ogwiritsa ntchito kusankha pakati pa kukhazikitsa chenjezo lotseka (chenjezo) la mphindi 3 kapena kuzimitsa CHENJEZO (chenjezo).

KUYAMBIRA KUYAMBIRA

Musanayambe kukonza, yikani batire yomwe mwapatsidwa.

• Gently pry open the access door, located below ON/OFF button, and remove the battery tray from the timer. (Saka YouTube video for “ST01 Programmable  Timer Battery Replacement”)
• Ikani batire la CR2 lomwe mwapatsidwa mu thireyi. Onetsetsani kuti mukufanana ndi + ndi - zolembera pa batire ndi thireyi. Ikani tray mu chowerengera nthawi.
• Chogulitsacho chimayamba ndikulowa mu MAN (pamanja) MODE yogwiritsira ntchito nthawi ikamalira 12:00 am.
  Zindikirani: Ngati chiwonetsero sichikuwunikira 12:00 am, fufuzani/kusinthani batire musanapitirize.

KUKHALA MALANGIZO

Tsatirani izi pakukhazikitsa koyambirira ndi kukonza kwa ST01 ndi EI600 zowerengera nthawi.
Yambani Bwezerani Nthawi

1. Dinani ndikugwira ON/OFF (pitirizani kugwira mpaka sitepe 3)
2. Pogwiritsa ntchito kopanira kapena cholembera, dinani ndikumasula batani la RESET.
3. Mukawona INIT pachiwonetsero ndiye kumasula batani ON/OFF PRO-TIP: Kusankha zinenero ndi ENG (Chingerezi), FRN (French), ndi SPAN (Spanish)
4. Gwiritsani ntchito + kapena - kusankha chilankhulo chomwe mukufuna
5. Dinani ON/OFF kuti mutsimikizire
6. Gwiritsani ntchito + kapena - kusankha chowerengera chomwe mukufuna kugwiritsa ntchito
   a. STD (Standard) timer (nthawi yotsegula ndi yozimitsa)
   b. PASI (Kuwerengera) chowerengera
7. Dinani ON/OFF kuti mutsimikizire

Chotsatira:

• Kwa Standard Operation (STD): 12: 00 am idzawalitsa kusonyeza MAN pambuyo pa Factory Reset; ku pulogalamu, pitani ku "Kukhazikitsa Koyamba."
• Pa Ntchito Yowerengera (PASI), chinsalucho chiziwonetsa ZOZIMITSA; ku pulogalamu, pitani ku "COUNTDOWN OPERATION ONLY."

KUGWIRITSA NTCHITO KWAMBIRI KUKHALA Koyamba

1. Dinani batani la MODE mpaka muwone SETUP pachiwonetsero
2. Dinani batani la ON/OFF kuti mutsimikizire
3. Gwiritsani ntchito + kapena - kukhazikitsa nthawi yatsiku HOUR (onetsetsani kuti AM kapena PM yanu ndiyolondola)
4. Dinani batani la ON/OFF kuti mutsimikizire
5. Gwiritsani ntchito + kapena - kukhazikitsa nthawi yamakono ya tsiku MINUTE
6. Dinani batani la ON/OFF kuti mutsimikizire
7. Dinani + kapena - kuti muyike YEAR yamakono
8. Dinani batani la ON/OFF kuti mutsimikizire
9. Dinani + kapena - kukhazikitsa MONTH yomwe ilipo
10. Dinani batani la ON/OFF kuti mutsimikizire
11. Dinani + kapena - kukhazikitsa DATE lapano
12. Dinani batani la ON/OFF kuti mutsimikizire
13. Onetsetsani kuti ikuwonetsa SIKU lolondola la WEEK (lero)
14. Dinani batani la ON/OFF kuti mutsimikizire
15. Dinani + kapena - kusankha ngati chowerengera chidzasinthira DAYLIGHT SAVING TIME (DST) masika ndi kugwa
    a. AUTO ikutanthauza kuti isintha zokha
    b. OFF kumatanthauza kuti sizisintha
16. Dinani batani la ON/OFF kuti mutsimikizire
17. Dinani + kapena - kuti musankhe TIME ZONE yanu
    a. Alaska (AKT), Atlantic (AT), Central (CT) (default), Eastern (ET), Hawaii (HT), Mountain (MT), Newfoundland (NT), Pacific (PT))
18. Dinani batani la ON/OFF kuti mutsimikizire
19. Dinani + kapena - kusankha DZIKO lanu (CTRY) a. USA (chosasinthika), Mexico (MEX), Canada (CAN)
20. Dinani batani la ON/OFF kuti mutsimikizire
    MALANGIZO: Onani nambala ya QR pansi pa chidziwitso cha tchati cha latitude ndi longitudo.
21. Dinani + kapena - batani kuti musankhe LATITUDE (LAT)
22. Dinani batani la ON/OFF kuti mutsimikizire
23. Dinani + kapena - batani kuti musankhe LONGITUDE (LONG)
24. Dinani batani la ON/OFF kuti mutsimikizire PRO-TIP: Muli ndi mwayi woti "Offset" makonda a Dusk ndi Dawn kuyambira mphindi 0 mpaka 99.
25. Dinani + kapena - batani kuti musinthe nthawi ya DAWN (mutha kuphatikiza chotsitsa apa).
    
26. Dinani batani la ON/OFF kuti mutsimikizire
27. Dinani + kapena - batani kuti musinthe nthawi ya DUSK (mutha kuphatikiza chotsitsa apa).
28. Dinani batani la ON/OFF kuti mutsimikizire (Mudzawona tsopano nthawi yanu ndi KUKHALA) - Pitirizani Kukhazikitsa Mapulogalamu

Kupanga Mapulogalamu
PRO-TIP: Musanakhazikitse Standard Programming Setup, muyenera kudziwa mtundu wa ndandanda womwe ukugwirizana ndi pulogalamu yanu kuchokera pamndandanda womwe uli pansipa.
T1= Chithunzi 1 - Yatsegulidwa pa DUSK. Kuchokera ku Dawn
T2= Chithunzi 2 - Yatsegulidwa pa DUSK. Kunyamuka nthawi ya 10:00 PM
T3= Chithunzi 3 - Yatsegulidwa pa DUSK. Kunyamuka nthawi ya 10:00 PM.
Pa 5:00 AM. Kuchokera ku Dawn.
Nthawi Yeniyeni - ON / OFF

1. Dinani batani la MODE mpaka muwone PGM pazenera.
2. Dinani batani ON / OFF kuti mulowe mndandanda wa mapulogalamu.

Patsogolo pa "Programming Template Events" kapena "Programming Specific Events".
Zochitika Zachiwonetsero cha Programming
MALANGIZO: Ma templates amayikidwa kwa masiku onse poyamba.

1. Mukalowa koyamba menyu ya PGM dinani + kapena - kusankha template.
2. Dinani batani la ON/OFF pa template yomwe mukufuna kugwiritsa ntchito
3. Chomaliza ndikudina MODE kuti musankhe AUTO kupita ku RAND (mwachisawawa).
   

Zochitika Zapadera za Programming
PRO-TIP: Mudzafunika zochitika zosachepera 2 (imodzi ya ON ndi ina yoyimitsa)

1. Mukalowa koyamba menyu ya PGM, dinani + kapena - kuti mupite patsogolo pa chochitika # 01.
2. Dinani batani la ON/OFF kuti mutsimikizire
3. Dinani + kapena - kuti musankhe ngati ichi chitha kukhala ON kapena WOZIMA
4. Dinani batani la ON/OFF kuti mutsimikizire
5. Dinani + kapena - kuti musankhe ngati ichi chikhala DAWN, DUSK kapena Specific Time chochitika (nthawi yeniyeni idzakhala ndi nthawi yowala)
6. Dinani batani la ON/OFF kuti mutsimikizire
7. Pa Nthawi Yeniyeni: Dinani + kapena - kuti muyike ola lomwe mukufuna (onetsetsani kuti AM kapena PM ndi yolondola)
8. Dinani ON/OFF batani kutsimikizira maola
9. Dinani + kapena - kuti muyike mphindi
10. Dinani batani la ON/OFF kuti mutsimikizire Dinani + kapena - batani kuti musankhe tsiku kapena gulu la masiku omwe mukufuna kuti chochitikachi chichitike.
    MALANGIZO:
    ONSE- masiku asanu ndi awiri onse a sabata Tsiku la Munthu Payekha- sankhani: DZUWA, MON, TUE, WED,
    THU, FRI kapena SAT
    MF- Lolemba mpaka Lachisanu
    WKD- Loweruka ndi Lamlungu
11. Dinani batani la ON/OFF kuti mutsimikizire
12. Ngati mukufuna kukhazikitsa chochitika china, Dinani batani + kuti mupite ku chochitika china ndikubwereza masitepe kuyambira sitepe 2.
13. Mukamaliza kuwonjezera zochitika, dinani batani la MODE kuti mupite patsogolo kupita ku AUTO (yokha) kapena RAND (mwachisawawa) MODE.

SINDANI, DULUNANI, FUTA ZOCHITA ZOYENERA

1. Dinani MODE mpaka PGM iwonekere pachiwonetsero.
2. Dinani ON/OFF kuti mutsimikizire.
3. Dinani + kapena - kusankha EDIT kapena ERASE
   a. EDIT ikulolani kuti musinthe ndondomeko yanu kuti mukhale gawo #4
   b. ERASE ichotsa zochitika ZONSE zokonzedwa.
   - Mukasankha ERASE, dinani ON/OFF kuti mutsimikizire, ndikupita patsogolo
   ZOCHITIKA ZA PROGRAMMING STANDARD ku(zi)zochitika, kapena dinani MODE kuti mupite ku MAN (Pamanja).
4. Dinani ON/OFF kuti mutsimikizire
5. Dinani batani + kuti mupeze nambala ya chochitika chomwe mukufuna kusintha, kudumpha kapena kufufuta (ERAS).
6. Dinani ON/OFF kuti mutsimikizire.
7. Dinani batani + kuti musankhe chimodzi mwazomwe zili pansipa.
   a. ONANI - Chowerengera chidzayatsa panthawiyi.
   b. ZOZIMA - Chowerengera chizimitsa panthawiyi.
   - Ngati mwasankha ON kapena WOZIMA, chonde bwererani ku Gawo #5 pansi pa "KUKONZEKERA ZOCHITIKA ZONSE"
   c. JULUKANANI - Izi zibisa kapena kudumpha chochitika chomwe mungafune kugwiritsa ntchito mtsogolo. Chosungira nthawi chidzanyalanyaza zochitika zilizonse "zolumpha". Izi ndizothandiza pazosowa zachilendo zamapulogalamu, monga makonda atchuthi.
   d. ERAS (kufufuta) - Izi zichotsa zomwe zasankhidwa.
   - Ngati mwasankha SKIP kapena ERASE mutha kupitiliza Khwerero #5 pansi pa "KUPANGIRA ZOCHITIKA ZONSE" kapena Dinani MODE kuti mubwerere ku AUTO, RAND (mwachisawawa) kapena MAN (pamanja).
   

COUNTDOWN OPERATION POKHALA Countdown Kukhazikitsa
MALANGIZO: Nthawi idzayenda mwachangu mukangogwira batani.

1. Gwiritsani ntchito batani la + kapena - kuti muyike kuchuluka kwa nthawi yowerengera yomwe mungafune.
   
2. Dinani batani la ON/OFF kuti mutsimikizire
3. Dinani ndikugwira mabatani a MODE ndi ON/OFF ndikugwira kwa masekondi asanu. Chiwonetserocho chidzawonetsa mndandanda wa WARN (chenjezo).
4. Dinani + kapena - kuti musankhe FLASH kapena WOZIMA.
   a. Chozimitsa - ntchito yochenjeza yazimitsa.
   b. Kung'anima - pamene timer ifika 3-mphindi musanatseke, idzawunikira magetsi oyendetsedwa (kapena dera lina) kwa 1 sekondi. Chizindikiro cha "sunburst" chidzawonekera pachiwonetsero
   
5. Dinani batani la MODE kuti mutsimikizire
6. Dinani + kapena - kuti musankhe LOCK yomwe mukufuna.
   a. Palibe - palibe ntchito yotseka yomwe yakhazikitsidwa.
   b. Imani kaye - ogwiritsa ntchito sangathe kugwiritsa ntchito Imani kuyimitsa kuwerengera nthawi.
   c. Nthawi - ogwiritsa ntchito amathansoview koma osasintha nthawi. Ogwiritsa ntchito amatha kusintha nthawi yowerengera koma sangadutse zokhoma zotseka.
   d. Zonse - kuyimitsa ndi kuyika kapena kusintha kotsekera kwa chotchinga chatsekedwa.
7. Dinani batani la MODE kuti mutsimikizire, chiwonetserocho chizimitsa

Sinthani Nthawi Yowerengera
MALANGIZO: Ngati chowerengera chili mu LOCK MODE, simungathe kusintha nthawi yoikika.
Kuti muyambe kapena kuyimitsa kuwerengera, dinani batani la ON/OFF.
Kuti muyimitse kuwerengera, dinani batani la Mode.

1. Dinani batani la ON / OFF mpaka chinsalu chikuwonekera
2. Dinani ndikugwira batani + kapena - - kuti mukhazikitse kuchuluka kwa nthawi yowerengera yomwe mukufuna.

Malangizo Owerengera Owerengera

• Kuyang'ana Kusintha kwa Nthawi - Dinani batani la + kapena - kuti muwone makonda a nthawi. Chiwonetserochi chikuwonetsa kuyika kwa nthawi kwa masekondi a 2.
• Kukhazikitsa Nthawi Yotsekeredwa - Kuti mutsegule chowerengera, chonde onani gawo la Kukhazikitsa Kuwerengera.
• Kukhazikitsa Timer Pamene SINAKIKITSIDWA - Pamene chowerengera sichikutsekedwa, wogwiritsa ntchito amatha kusintha makonda, koma ayenera kuzimitsa chowerengera asanasinthe.
• Kuyimitsa Kuwerengera - Pamene chowerengera sichinatsekedwe, dinani batani la MODE kuti muyimitse kuwerengera komwe kukuchitika.
  Imitsani mipiringidzo kung'anima pamene chiwerengero chikugwirabe ntchito. Dinani MODE kachiwiri kuti mupitirize kuwerengera kapena dinani batani la ON/OFF kuti muzimitsa katunduyo.
• Kufupikitsa kapena kutalikitsa Kuwerengera kukuchitika
  - Kuti musinthe kuwerengera komwe kukuchitika, dinani ndikugwira batani la + kapena - kapena batani la ON/OFF mpaka chiwonetsero chikuwonetsa nthawi yomwe mukufuna kuti muyendere mozungulira.
  Chowerengeracho chikayamba kuzungulira kotsatira, kuwerengera kumabwereranso kumakonzedwe okonzedwa.
• Mukatsekedwa mukhoza kuwonjezera nthawi yochuluka kufika pa nthawi yochuluka yomwe yakhazikitsidwa.
• Kugwiritsa Ntchito Remote Switch mu 3-Way - Mukawongolera chowerengera ndi chosinthira chakutali, sinthani chosinthira chakutali kamodzi kuti mutsegule kapena kuzimitsa.

KUYANG'ANIRA

PRO-TIP: Mukayika chowerengera nthawi ndi kontrakitala kapena katundu wamagalimoto, fyuluta ya phokoso imalimbikitsidwa (ET-NF). Example ya single pole ndi mawaya atatu amatsata. Pazinthu zina za njira zitatu zolumikizira waya, pitani ku www.intermatic.com.
Chotsani mphamvu pa gulu la utumiki.

1. Chotsani zosintha zapakhoma, ngati zikuyenera.
2. Mangani ma waya omwe alipo mpaka 7/16 ".
3. Yambani chowerengera mubokosi la khoma.

Kulumikizana Kwamodzi

A	Black - Imalumikizana ndi waya wotentha (wakuda) kuchokera ku Gwero la Mphamvu
B	Buluu - Imalumikizana ndi waya wina (wakuda) kuchokera pamtolo
C	Wofiyira - Waya uyu sagwiritsidwa ntchito poyika ma switch amodzi. Chophimba chokhala ndi cholumikizira chopindika
D	Green - Imalumikizana ndi nthaka yomwe wapatsidwa

Wiring Wanjira zitatu
PRO-TIP: Mtunda pakati pa timer ndi chosinthira chakutali suyenera kupitirira 100 mapazi.
Mawaya omwe akuwonetsedwa pansipa ndi a chowerengera cholowa m'malo mwa njira zitatu kumbali ya mzere.

A	Black Connect to the "COMMON" -waya wachotsedwa
	terminal ya switch inasinthidwa
I	Buluu - Lumikizani ku waya wina womwe wachotsedwa pa switch yomwe ikusinthidwa. Jambulani mtundu wawaya wolumikizidwa ku waya wabuluu kuti mugwiritse ntchito pokhazikitsa mbali ya katundu
	Chofiyira - Lumikizani ku waya wotsala wochotsedwa chosinthira chikusinthidwa. Jambulani mtundu wa waya wolumikizidwa ku waya wofiyira kuti mugwiritse ntchito poika katundu
D	Green - Lumikizani ku nthaka yomwe mwapatsidwa
E	Jumper Wire -Pa switch ina yanjira zitatu, ikani waya wodumphira pakati pa waya B ndi terminal wamba.

KUMALIZA KUSINTHA

1. Onetsetsani kuti mawaya omwe mwapatsidwa ndi otetezeka, kenaka ikani mawaya mu bokosi la khoma, kusiya malo owerengera.
2. Pogwiritsa ntchito zomangira zomwe zaperekedwa, tetezani chowerengera ku bokosi la khoma.
3. Phimbani chowerengera ndi khoma la khoma ndikutetezani pogwiritsa ntchito zomangira zomwe zaperekedwa.
4. Pa mawaya anjira zitatu, ikani chosinthira chakutali mubokosi la khoma.
5. Ikani khoma la khoma ndikutetezedwa.
6. Lumikizaninso mphamvu pagawo lothandizira.

Kuyesa Timer
Onetsetsani kuti chowerengera chikuwonetsa MAN (pamanja) MODE pakuyesa
Mayeso a Wiring Amodzi
Kuti muyese chowerengera, dinani ON/OFF kangapo. Chowerengera chiyenera "kudina" ndipo Nyali Yoyang'aniridwa kapena chipangizo (katundu) chiyenera kuyatsa kapena KUZIMA.
Mayeso a Wiring Wanjira zitatu

1. Kuti muyese chowerengera, yesani ndi chosinthira chakutali pamalo aliwonse ake awiri.
2. Dinani ON/OFF kangapo. Chosungira nthawi chiyenera "kudina" ndipo kuwala koyendetsedwa kapena chipangizo (katundu) chiyenera kuyatsa kapena KUZIMA.
3. Ngati chowerengera chikudina, koma katunduyo sagwira ntchito:
   a. Chotsani mphamvu pa gulu la utumiki.
   b. Yang'ananinso mawaya ndikuwonetsetsa kuti katunduyo akugwira ntchito.
   c. Lumikizaninso mphamvu pagawo lothandizira.
   d. Yesaninso.
4. Ngati chowerengera chikudina, koma katunduyo akugwira ntchito pokhapokha chosinthira chakutali chili m'malo ake awiri, bwerezani Gawo 3, zotsatsa, koma sinthani mawaya awiri oyenda (mawaya Pakati pa chowerengera ndi chosinthira chakutali chanjira zitatu) cholumikizidwa ndi chofiira ndi. mawaya a blue timer PRO-TIP: Funsani katswiri wamagetsi woyenerera ngati chosinthira ndi chowerengera sichikugwira ntchito momwe amafunira
5. Pamene chowerengera "chadina" ndipo chipangizo chowongolera chiyatsa ndikuzimitsa monga momwe adakonzera, chowerengeracho chimayikidwa bwino!

KUSAKA ZOLAKWIKA

Zindikirani: : Kuti mudziwe zambiri zaupangiri, funsani Intermatic Technical Support pa: 815-675-7000.

Kuwonedwa Vuto	Chifukwa Chotheka	Zoyenera kuchita
Chiwonetsero cha nthawi chilibe kanthu, ndipo chowerengera sichi "kudina" mukayesa kuyatsa kapena kuyimitsa.	• Batiri likusowa • Battery ilibe ndalama • Battery inayikidwa molakwika	• Ikani batire • Bwezerani batire • Onetsetsani kuti batire yayikidwa bwino.
Chowerengera sichimayatsa/KUZImitsa koma mawonekedwe amawoneka ngati abwinobwino	• Chowerengera sichinakhazikitsidwe mu AUTO, RAND, kapena MAN MODE • Batire yachepa ndipo ikufunika kusinthidwa	• Dinani MODE kuti musankhe MODE yomwe mukufuna kugwiritsa ntchito • Bwezerani batire
Timer ibwereranso ku 12:00	• Timer waikidwa molumikizana ndi contactor kapena galimoto katundu.	• Ikani fyuluta ya phokoso (ET-NF) pagwero la phokoso
Chowerengera sichilowa mu mawonekedwe a AUTO kapena RAND pomwe "MODE" ikanikizidwa	• Palibe ndondomeko yomwe yasankhidwa	• Pitani ku “Programming Standard Zochitika” gawo
Nthawi imagwira ntchito nthawi yolakwika, kapena kudumpha nthawi za EVENT zokonzedwa	• Ndondomeko yogwira ntchito imakhala ndi zochitika zotsutsana kapena zolakwika • Batiri likhoza kukhala lofooka. • Timer ili mu RAND mode, yomwe imasinthasintha nthawi mpaka +/- 15 mphindi	• Review zochitika zokonzedwa, sinthani ngati pakufunika. • Bwezerani batire. • Sankhani "Auto Mode"
Kutsegula kumagwira ntchito pokhapokha: chosinthira chakutali (njira zitatu) chili pamalo amodzi, kapena chowerengera chinyalanyaza chosinthira chakutali.	• Chosinthira chakutali chili ndi waya molakwika.	• Yang'ananinso mawaya, makamaka a jumper
Chowerengeracho chimanyalanyaza chosinthira chakutali chanjira zitatu ngakhale chili ndi waya moyenera, kapena katunduyo amazimitsa atangoyatsidwa.	• Chosinthira chakutali kapena chowerengera nthawi chili ndi mawaya molakwika. • Pali kutalika kwa waya (kuposa mapazi 100). • Chosinthira chakutali sichikuyenda bwino kapena kutha.	• Lumikizanani ndi wodziwa magetsi
Thireyi ya batri ndiyovuta kuyisintha.	• Batiri silinakhazikitsidwe mu thireyi • Thireyiyo ndi yolakwika • Ma tabu okhudzana ndi thireyi amapindika	• Ikani batire mu thireyi, kenako yikaninso.

CHITIMIKIZO CHOKHALA

Thandizo lachitsimikizo likupezeka mwa (a) kubwezera malonda kwa wogulitsa yemwe adagula katunduyo kapena (b) kutsiriza chikalata cha chitsimikizo pa intaneti pa
https://www.intermatic.com/Support/Warranty-Claims. Chitsimikizochi chimapangidwa ndi: Intermatic Incorporated, 1950 Innovation Way, Suite 300, Libertyville, IL 60048. Kuti mudziwe zambiri za malonda kapena chitsimikizo pitani ku: http://www.Intermatic.com kapena kuitana 815-675-7000, MF 8AM mpaka 4:30pm

Chonde jambulani kachidindo ka QR kuti mupeze tchati chautali ndi latitude

https://l.ead.me/bcrVyB

Zolemba / Zothandizira

INTERMATIC ST01 Mu Wall Timer yokhala ndi Astro kapena Countdown Feature [pdf] Buku Logwiritsa Ntchito ST01 Mu Wall Timer yokhala ndi Astro kapena Countdown Feature, ST01, Mu Wall Timer yokhala ndi Astro kapena Countdown Feature, kapena Countdown Feature, Countdown Feature

Maumboni

• Buku Logwiritsa Ntchito