AUDIOMS AUTOMATIKA SED2 Single mechiri na interface ihe ngbanwe dị iche
FAQ
- Q: Kedu otu m ga-esi mee ka ntinye koodu agbakwunyere ike mgbe ejikọrọ na interface SED2?
- A: A na-akwado koodu ntinye agbakwunyere site na isi iyi ike 5V nke onye ọkwọ ụgbọ ala servo DCS-100-A nyere site na ọdụ ụgbọ mmiri Encoder na DCS-100-A servo ọkwọ ụgbọ ala.
- Q: Kedu ihe m kwesịrị ime iji belata nnyonye anya electromagnetic?
- A: Iji belata ndabichi elektrọnik, jiri eriri echedoro maka njikọ dị n'etiti interface SED2 na onye ọkwọ ụgbọ ala servo DCS-100-A. Na mgbakwunye, debe ogologo eriri USB ka ọ dị mkpụmkpụ ka enwere ike.
Nkọwa
Otu gwụchara na interface encoder dị iche SED2 (Ọnyonyo 1.1) bụ onye ọkwọ ụgbọ ala nke na-atụgharị akara ntinye agwụcha agwụ (A, B na Z) site na ntinye ntinye agbakwunyere n'ime mpụta dị iche (mmekọ) (A+, A-, B+, B) -, Z+ na Z-). Ezubere ya maka ọkọnọ voltages of incremental encoders na nso site 5V ruo 24V, kacha ruo 30V (High Transistor Logic – HTL).
The encoder interface SED2 na-eji maka njikọ nke otu njedebe (nhọrọ dị iche) incremental encoders na Audioms Automatika DC servo ọkwọ ụgbọala DCS-3010 (-HV) ma ọ bụ na DCS-100-A v.3 servo ọkwọ ụgbọala, yana na sistemu sitere na ndị nrụpụta ndị ọzọ chọrọ ihe ngbanwe koodu.
SED2 Encoder interface njikọ
SED2 nwere njikọ 2 na ya (Fig 2.1):
- Njikọ 5-pole nwere ike ịwepụ maka njikọ na ntinye ntinye ntinye (Con.1 - Figure 2.1). Tebụl 2.1 na-enye pinout nke njikọ maka ijikọ ihe ntinye ntinye. A na-edowe ihe mgbochi 4.7 kΩ na ntinye A, B na Z, na
- Njikọ 8-pin nwere ike iwepụ (Con.2 - Figure 2.1) nke akara ngosi dị iche iche sitere na ntinye ntinye ntinye dị n'ụdị A +, A-, B+, B-, Z+ na Z-. Tebụl 2.2 na-enye nkọwa nke ntụtụ nke njikọ a.
The encoder interface SED2 nwere wuru na-2 egosi LEDs, red n'akụkụ njikọ Con.1 na akwụkwọ ndụ akwụkwọ ndụ na n'akụkụ nke njikọ Con.2 (Nyocha 2.1).
Tebụl 2.1: Nkọwa nke ntụtụ nke njikọ 5-pin (Con.1)
 |
Pin Nke | Aha | Nkọwa | Ọrụ |
| 1 | G | GND - Encoder |
Njikọ ntinye koodu na-abawanye |
|
| 2 | Z | Ọwa koodu Z – Ntinye | ||
| 3 | B | Ọwa koodu B – Ntinye | ||
| 4 | A | Ọwa koodu nzuzo – Ntinye | ||
| 5 | +V | Ihe ngbanwe ike ọkọnọ |
Tebụl 2.2: Nkọwa nke ntụtụ nke njikọ 8-pin (Con.2)
 |
Pin Nke | Aha | Nkọwa | Ọrụ |
| 1 | +V | Ihe mkpuchi ike ọkọnọ 5V ruo 24V |
Mpụta akara ngbanwe dị iche |
|
| 2 | A+ | Ọwa koodu koodu A+ – Mpụta | ||
| 3 | A- | A- encoder ọwa – Mpụta | ||
| 4 | B+ | Ọwa koodu B+ – Mpụta | ||
| 5 | B- | Ọwa koodu B-Mpụta | ||
| 6 | Z+ | Ọwa koodu Z+ – Mpụta | ||
| 7 | Z- | Ọwa koodu koodu Z – Mpụta | ||
| 8 | GND | GND |
Ijikọ ihe ngbanwe SED2 na onye ọkwọ ụgbọ ala servo DCS-100
Ọgụgụ 2.2 na-enye exampnke ijikọ ihe ntinye ntinye agbakwunyere na otu ọkwọ ụgbọ ala servo DCS-100-A site na SED2 encoder interface. A na-akwado koodu ntinye agbakwunyere site na isi iyi ike 5V nke DCS-100-A servo driver nyere site na ọdụ ụgbọ mmiri Encoder (Con.2 na DCS-100-A servo driver).
IHE: A na-atụ aro ka ogologo eriri USB dị n'etiti ntinye ntinye na ntinye ntinye SED2 dị mkpụmkpụ dịka enwere ike.
Iji belata mmetụta nke nnyonye anya electromagnetic dị elu, a na-atụ aro ka iji eriri mkpuchi maka njikọ nke SED2 encoder interface na DCS-100-A servo driver. Igwe njikọ koodu ekwesịghị ịdị ogologo karịa ngwa a kapịrị ọnụ chọrọ.
Kpọtụrụ
NKWUKWU NDỤMỌDỤ:
- Ver. 1.0, Eprel 2024, Ndozigharị izizi
Kpọtụrụ
- Audioms Automatika doo Kragujevac, Serbia
- web: www.audiohms.com
- ozi-e: office@audiohms.com
Akwụkwọ / akụrụngwa
 |
AUDIOMS AUTOMATIKA SED2 Single mechiri na interface ihe ngbanwe dị iche [pdf] Akwụkwọ ntuziaka onye ọrụ DCS-3010 -HV, DCS-100-A v.3, SED2 Single kwụsịrị na Interface Encoder dị iche, SED2, SED2 Encoder Interface, Otu gwụchara na Interface Encoder dị iche, Interface Encoder dị iche, Interface Encoder, Interface |