INCWADI YOKUFAKA
ZD-IN
IZILUMKISO ZOKUQALA
Igama elithi ISILUMKISO elandulelwa luphawu 
ibonisa iimeko okanye izenzo ezibeka ukhuseleko lomsebenzisi emngciphekweni.
Igama elithi ATTENTION elandulelwa sisimboli ibonisa iimeko okanye izenzo ezinokuthi zonakalise isixhobo okanye isixhobo esixhunyiwe. Iwaranti iya kuba lilize kwaye ingabikho kwimeko yokusetyenziswa ngokungafanelekanga okanye tampering kunye nemodyuli okanye izixhobo ezibonelelwe ngumenzi njengoko kuyimfuneko ekusebenzeni kwayo okuchanekileyo, kwaye ukuba imiyalelo equlethwe kule ncwadana ayilandelwa.
|
ISILUMKISO: Umxholo opheleleyo wale ncwadana kufuneka ufundwe phambi kwawo nawuphi na umsebenzi. Imodyuli kufuneka isetyenziswe kuphela ngabasebenzi bombane abaqeqeshiweyo. Amaxwebhu athile ayafumaneka nge-QR-CODE eboniswe kwiphepha loku-1. |
 |
Imodyuli kufuneka ilungiswe kwaye iindawo ezonakalisiweyo zitshintshwe nguMenzi. Imveliso inovelwano ngokukhutshwa kwe-electrostatic. Thatha amanyathelo afanelekileyo ngalo naluphi na umsebenzi. |
 |
Ukulahlwa kwenkunkuma yombane neye-elektroniki (esebenzayo kwiManyano yaseYurophu nakwamanye amazwe anokurisayikilishwa). Isimboli kwimveliso okanye ukupakishwa kwayo ibonisa imveliso kufuneka inikezelwe kwiziko lokuqokelela eligunyazisiweyo ukuba liphinde lisetyenziswe inkunkuma yombane neye-elektroniki. |
UHLELO LWEMODYULI
IIMPAWU NGE-LED PHAMBILI
| I-LED | IMEKO | Intsingiselo ye-LED |
| PWR Green | ON | Isixhobo sinikwe amandla ngokuchanekileyo |
| FAIL yellow | ON | I-Anomaly okanye impazamo |
| FAIL yellow | Ukudanyaza | Ukucwangcisa okungalunganga |
| I-RX Ebomvu | ON | Itshekhi yoqhagamshelo |
| I-RX Ebomvu | Ukudanyaza | Ukufunyanwa kwepakethi kugqityiwe |
| TX Ebomvu | Ukudanyaza | Ukuhanjiswa kwepakethi kugqityiwe |
INGCACISO YOBUGCISA
| IZIQINISEKISO |  https://www.seneca.it/products/z-d-in/doc/CE_declaration |
| UKUKHUSELELWA |  |
| UKUNIKEZWA AMANDLA | Umqulutage: 10 ÷ 40Vdc; 19 ÷ 28Vac; 50 ÷ 60Hz Ukufunxa: Eqhelekileyo: 1.5W @ 24Vdc, Ubukhulu: 2.5W |
| SEBENZISA | Ukusetyenziswa kwiindawo ezineqondo longcoliseko 2. Iyunithi yokubonelela ngombane kufuneka ibe yiklasi 2. |
| IMEKO ZOKUSINGQONGILEYO | Ubushushu: -10÷ + 65°C Ukufuma: 30% ÷ 90% kwi-40 °C ukunganciphisi. Ukuphakama: Ukuya kuma-2,000 m ngaphezu komphakamo wolwandle Ubushushu bokugcina: -20÷ + 85°C Inqanaba lokhuseleko: IP20. |
| INDIBANO | IEC EN60715, 35mm DIN kaloliwe kwindawo nkqo. |
| IZIXHOBO | Iitheminali ze-screw ezi-3 ezikhutshwayo, i-5mm pitch, icandelo le-2.5mm2 Isidibanisi ngasemva i-IDC10 ye-DIN bar 46277 |
| IZIMPAWU | |
| Uhlobo lwenkxaso igalelo: |
I-Reed, i-Contatto, i-PNP ekufutshane, i-NPN (ngokuchasana kwangaphandle) |
| Inani lamajelo: | I-5 (4+ 1) i-self-powered kwi-16Vdc |
| Inani elipheleleyo rhoqo |
I-100Hz yamajelo ukusuka kwisi-1 ukuya kwisi-5 10 kHz kuphela igalelo 5 (emva kokusetha) |
| UL (Isimo sicinyiwe) | 0 ÷ 10 Vdc, I <2mA |
| UH (imo IYAVULWA) | 12 ÷ 30 Vdc; Mna > 3mA |
| Okwangoku kufakwe | 3mA (ngegalelo ngalinye elisebenzayo) |
| Ukhuseleko | Ngokusetyenziswa kwee-TVS ezicinezelayo ze-600 W/ms. |
UQINISEKISO LWESETHINGI ZEFEKtri
| Zonke i-DIP-zitshintshela ngaphakathi | CIMA |
| Iiparamitha zonxibelelwano zeModbus protocol: | 38400 8, N, 1 Idilesi 1 |
| Uguqulo lobume begalelo: | UKHUBAZEKILE |
| Isihluzo sedijithali | 3ms |
| Iitotali | Ukubala ukuya kunyuso |
| Umjelo we-5 kwi-10 kHz | Kukhubazekile |
| Ixesha le-modbus latency | 5ms |
IMIGAQO YOQHAGAMSHELO lweModbus
- Faka iimodyuli kuloliwe weDIN (120 max)
- Qhagamshela iimodyuli ezikude usebenzisa iintambo zobude obufanelekileyo. Le theyibhile ilandelayo ibonisa ubude bedatha yentambo:
-Ubude bebhasi: ubude obuninzi bothungelwano lweModbus ngokwenqanaba leBaud. Lo bubude beentambo ezidibanisa iimodyuli ezimbini ezikude kakhulu (jonga uMzobo 1).
- Ubude bokukhutshwa: ubude obuninzi be-derivation ye-2 m (jonga i-Diagram 1).
Umzobo 1
| Ubude bebhasi | Ubude bokukhutshwa |
| 1200 m | 2 m |
Ukusebenza okuphezulu, kuyacetyiswa ukuba usebenzise iintambo ezikhethekileyo ezikhuselekileyo, ezifana ne-BELDEN 9841.
I-IDC10 ISIHLANGANISI
Ukunikezelwa kwamandla kunye ne-interface ye-Modbus ifumaneka ngokusebenzisa i-Seneca DIN ibhasi kaloliwe, nge-IDC10 isiqhagamshelo esingasemva, okanye i-Z-PC-DINAL2-17.5 i-accessory.
isiqhagamshelo ngasemva (IDC 10)
Intsingiselo yezikhonkwane ezahlukeneyo kwidibansi ye-IDC10 ibonisiwe kumzobo ukuba unqwenela ukunikezela ngemiqondiso ngokuthe ngqo ngayo.
UKUBEKA I-DIP-SWITISHI
Isikhundla se-DIP-iiswitshi sichaza iiparameters zonxibelelwano lwe-Modbus kwimodyuli: Idilesi kunye ne-Baud Rate
Le theyibhile ilandelayo ibonisa amaxabiso e-Baud Rate kunye neDilesi ngokwesicwangciso seeswitshi ze-DIP:
| DIP-Tshintsha isimo | |||||
| SW1 POSITION | I-BAUD RATE |
SW1 POSITION | Idilesi | POSITION | ISIQINISEKISO |
| 1 2 3 4 5 6 7 8 | 3 4 5 6 7 8 | 10 | |||
| —————- |
9600 |  |
#1 | |
Kukhubazekile |
| ———— |
19200 | |
#2 | |
Ivuliwe |
| ———– |
38400 | ••••••• | # ... | ||
| ———– |
57600 | |
#63 | ||
| ——- |
Ukusuka EEPROM |
|
Ukusuka EEPROM |
||
Phawula: Xa i-DIP itshintshela u-3 ukuya ku-8 IVIMILE, useto lonxibelelwano luthathwa kwiprogramming (EEPROM).
Phawula I-2: Umgca we-RS485 kufuneka upheliswe kuphela ekupheleni komgca wonxibelelwano.
Useto lweedip-switshi kufuneka luhambelane nesetingi kwiirejista.
Inkcazo yeerejista iyafumaneka kwi-USER MANUAL.
UKUQHAGAMSHELWA KOMbane
Ukunikezwa Amandla:
Imida ephezulu mayingagqithiswa ukwenzela ukuthintela umonakalo omkhulu kwimodyuli.
Ukuba umthombo wonikezelo lwamandla awukhuselwanga ekugqithiseni, i-fuse yokhuseleko kufuneka ifakwe kumgca wonikezelo lwamandla ngexabiso elifanelekileyo kwinto efunwa yimeko.
Modbus RS485
Uqhagamshelwano lwe-RS485 yonxibelelwano usebenzisa i-MODBUS master system njengenye indlela yebhasi ye-Z-PC-DINx.
QAPHELA: Isalathiso soqhagamshelwano lwe-RS485 polarity alulungelelaniswanga kwaye kwezinye izixhobo zinokujikwa.
IZIMPAWU
IISETHINGI ZOKUFAKA:
Useto oluhlala lukhona:
Igalelo #1: 0 - 100 Hz (16BIT)
Igalelo #2: 0 - 100 Hz (16BIT)
Igalelo #3: 0 - 100 Hz (16BIT)
Igalelo #4: 0 - 100 Hz (16BIT)
Igalelo #5: 0 - 100 Hz (16BIT)
Igalelo #5 linokusetwa njengetotali:
Igalelo #5: 0 - 10 kHz (32BIT)
QAPHELA
Umda wonikezelo lwamandla aphezulu kufuneka ungagqithiswa, njengoko oku kunokubangela umonakalo omkhulu kwimodyuli. Cima imodyuli phambi kokudibanisa amagalelo kunye neziphumo.
Ukuhlangabezana neemfuno zokhuselo lwe-electromagnetic:
- sebenzisa iintambo zomqondiso ezikhuselekileyo;
- qhagamshela isikhuselo kwisixokelelwano somhlaba esikhethiweyo;
- ifyuzi ene-MAX. ireyithingi ye-0,5 A kufuneka ifakwe kufutshane nemodyuli.
- zahlula iintambo ezikhuselweyo kwezinye iintambo ezisetyenziselwa ukufakelwa kombane (ii-inverters, ii-motor, ii-oveni zokungenisa, njl njl…).
- qinisekisa ukuba imodyuli ayibonelelwanga ngevolthi yonikezelotagengaphezulu kunoko kubonisiwe kwiinkcukacha zobugcisa ukwenzela ukuba ungonakalisi.
SENECA srl; Nge-Austria, 26 - 35127 - PADOVA - ITALY;
Umnxeba. +39.049.8705359 -
Ifeksi +39.049.8706287
IINKCUKACHA ZOQHAKAMSHELWANO
Uxhaso lobuchwepheshe
inkxaso@seneca.it
Ulwazi lwemveliso
sales@seneca.it
Olu xwebhu luyipropathi ye-SENECA srl. Iikopi kunye nokuveliswa kwakhona akuvumelekanga ngaphandle kokuba kugunyazisiwe. Umxholo wolu xwebhu uhambelana neemveliso ezichazwe kunye nobuchwepheshe. Idatha echaziweyo inokuguqulwa okanye yongezwe ngeenjongo zobugcisa kunye / okanye ukuthengisa.
Amaxwebhu / Izibonelelo
 |
I-SENECA ZD-IN Igalelo leDijithali okanye iiModyuli zokuPhuma [pdf] Incwadi Yomyalelo I-ZD-IN, iNgeniso yeDijithali okanye iiModyuli zeZiphumezo, i-ZD-IN igalelo leDijithali okanye iiModyuli zeZiphumezo |
