MANIN SHIGA
ZD-IN

GARGADI NA FARKO

Kalmar WARNING ta riga da alamar yana nuna yanayi ko ayyuka waɗanda ke sanya amincin mai amfani cikin haɗari.
Kalmar ATTENTION ta riga da alamar yana nuna yanayi ko ayyuka waɗanda zasu iya lalata kayan aiki ko kayan haɗin da aka haɗa. Garanti zai zama marar amfani a yayin amfani mara kyau ko tampyin aiki tare da na'ura ko na'urorin da masana'anta suka bayar kamar yadda ya cancanta don aikin sa daidai, kuma idan ba a bi umarnin da ke cikin wannan jagorar ba.

	GARGADI: Dole ne a karanta cikakken abin da ke cikin littafin kafin kowane aiki. ƙwararrun masu lantarki ne kawai za su yi amfani da ƙirar. Akwai takamaiman takaddun ta hanyar QR-CODE da aka nuna a shafi na 1.
	Dole ne a gyara ƙirar kuma a maye gurbin ɓarna da Manufacturer. Samfurin yana kula da fitar da wutar lantarki. Ɗauki matakan da suka dace yayin kowane aiki.
	Zubar da sharar lantarki da lantarki (wanda ake amfani da shi a cikin Tarayyar Turai da sauran ƙasashe tare da sake amfani da su). Alamar da ke kan samfurin ko marufi na nuna dole ne a miƙa samfurin zuwa cibiyar tattarawa da aka ba da izini don sake sarrafa sharar lantarki da lantarki.

MULKI MULKI

ALAMOMIN TA HANYAR LED AKAN GABA

LED	MATSAYI	LED ma'ana
Farashin PWR	ON	Ana kunna na'urar daidai
RASHIN rawaya	ON	Anomaly ko kuskure
RASHIN rawaya	Walƙiya	Saitin kuskure
RX ja	ON	Duban haɗi
RX ja	Walƙiya	An kammala karɓar fakiti
TX ja	Walƙiya	An gama isar da fakiti

BAYANIN FASAHA

TAMBAYOYI	https://www.seneca.it/products/z-d-in/doc/CE_declaration
INSULATION
TUSHEN WUTAN LANTARKI	Voltage: 10 ÷ 40Vdc; 19 ÷ 28Vac; 50 ÷ 60 Hz Abun sha: Na al'ada: 1.5W @ 24Vdc, Max: 2.5W
AMFANI	Yi amfani da shi a cikin mahalli masu digiri na 2. Dole ne sashin samar da wutar lantarki ya zama aji 2.
YANAYIN MAHALI	Zazzabi: -10÷ + 65°C Humidity: 30%÷ 90% a 40°C mara sanyaya. Tsayi: Har zuwa mita 2,000 sama da matakin teku Yanayin ajiya: -20÷ + 85°C Matsayin kariya: IP20.
MAJALIYYA	IEC EN 60715, 35mm DIN dogo a tsaye.
HANYOYI	3-hanyar cire dunƙule tashoshi, 5mm farar, 2.5mm2 sashe Mai haɗin baya IDC10 don DIN mashaya 46277

Bayani
Nau'in tallafi abubuwan shiga:	Reed, Contatto, PNP kusanci, NPN (tare da juriya na waje)
Yawan tashoshi:	5 (4+ 1) mai ikon kai a 16Vdc
Matsakaicin jimla mita	100 Hz don tashoshi daga 1 zuwa 5 10 kHz kawai don shigar da 5 (bayan saiti)
UL (Kashe Matsayi)	0 ÷ 10 Vdc, I <2mA
UH (yanayin ON)	12 ÷ 30 Vdc; ina > 3mA
Samu halin yanzu	3mA (ga kowane shigarwa mai aiki)
Kariya	Ta hanyar masu hana TVS na wucin gadi na 600 W/ms.

TSARIN KASANCEWA NA FARKO

Duk DIP-switchs in	KASHE
Siffofin sadarwa na ƙa'idar Modbus:	38400 8, N, 1 Adireshi 1
Juyar da yanayin shigarwa:	RASHIN LAFIYA
Tace ta dijital	3ms
Totalizers	Ƙididdigar zuwa haɓaka
Channel 5 a 10 kHz	An kashe
Modbus latency lokaci	5ms

Dokokin Haɗin Modbus

1. Shigar da kayayyaki a cikin DIN dogo (120 max)
2. Haɗa na'urori masu nisa ta amfani da igiyoyi na tsayin da ya dace. Tebur mai zuwa yana nuna bayanan tsawon kebul:
   - Tsawon bas: matsakaicin tsayin hanyar sadarwar Modbus gwargwadon ƙimar Baud. Wannan shine tsayin igiyoyin igiyoyin da ke haɗa nau'ikan mafi nisa guda biyu (duba zane na 1).
   - Tsawon abin da aka samo: matsakaicin tsayin 2 m (duba zane na 1).

Zane 1

Tsawon bas	Tsawon fitarwa
1200 m	2 m

Don iyakar aiki, ana ba da shawarar yin amfani da igiyoyi masu kariya na musamman, kamar BELDEN 9841.

MAI HADA IDC10

Ana samun wutar lantarki da Modbus dubawa ta amfani da motar dogo ta Seneca DIN, ta hanyar haɗin baya na IDC10, ko na'urorin haɗi na Z-PC-DINAL2-17.5.

Mai Haɗin Baya (IDC 10)
Ana nuna ma'anar fil daban-daban akan mai haɗin IDC10 a cikin adadi idan kuna son samar da sigina kai tsaye ta hanyarsa.

KASANCEWA DA TSAMA

Matsayin DIP-switchers yana bayyana sigogin sadarwa na Modbus na module: Adireshin da Baud Rate
Tebu mai zuwa yana nuna ƙimar ƙimar Baud da Adireshin bisa ga saitin maɓallan DIP:

Matsayin DIP-Switch
MATSAYI SW1	BAUD RATE	MATSAYI SW1	ADDRESS	MATSAYI	MAI KYAUTA
1 2 3 4 5 6 7 8		3 4 5 6 7 8		10
—————	9600		#1		An kashe
————	19200		#2		An kunna
———–	38400	•••••••	# ...
———–	57600		#63
---	Daga EEPROM		Daga EEPROM

Lura: Lokacin da DIP ya kashe 3 zuwa 8, ana ɗaukar saitunan sadarwa daga shirye-shirye (EEPROM).
Lura 2: Dole ne a ƙare layin RS485 kawai a ƙarshen layin sadarwa.
Dole ne saitunan tsoma-switches su dace da saitunan akan rajistar.
Ana samun bayanin rijistar a cikin MANZON ALLAH.

HANYAR LANTARKI

Tushen wutan lantarki:
Ba dole ba ne a ƙetare manyan iyakoki don guje wa mummunar lalacewa ga tsarin.
Idan tushen wutar lantarki ba a kiyaye shi daga kitsewa ba, dole ne a shigar da fiusi mai aminci a cikin layin samar da wutar lantarki tare da ƙimar da ta dace da abin da yanayin ke buƙata.

Modbus RS485
Haɗin don sadarwar RS485 ta amfani da tsarin babban tsarin MODBUS azaman madadin bas ɗin Z-PC-DINx.
NB: Alamar polarity na haɗin RS485 ba ta daidaita ba kuma a wasu na'urori na iya jujjuya su.

Bayani

SAI TSARI:
Saitunan asali:
Shigarwa #1: 0 - 100 Hz (16BIT)
Shigarwa #2: 0 - 100 Hz (16BIT)
Shigarwa #3: 0 - 100 Hz (16BIT)
Shigarwa #4: 0 - 100 Hz (16BIT)
Shigarwa #5: 0 - 100 Hz (16BIT)
Ana iya saita shigarwar #5 azaman jimla:
Shigarwa #5: 0 - 10 kHz (32BIT)

HANKALI

Ba dole ba ne a ƙetare iyakokin samar da wutar lantarki na sama, saboda wannan na iya haifar da mummunar lalacewa ga tsarin. Kashe module ɗin kafin haɗa bayanai da abubuwan fitarwa.

Don saduwa da buƙatun rigakafi na lantarki:

• amfani da igiyoyin sigina masu kariya;
• haɗa garkuwa zuwa tsarin ƙasa na kayan aiki na fifiko;
• fuse tare da MAX. rating na 0,5 A dole ne a shigar kusa da module.
• ware igiyoyi masu kariya daga wasu igiyoyi da ake amfani da su don shigar da wutar lantarki (inverters, motors, induction oven, da sauransu…).
• tabbatar da cewa ba'a kawo module ɗin tare da wadatar voltage sama da abin da aka nuna a cikin ƙayyadaddun fasaha don kada ya lalata shi.

www.seneca.it/products/zd-in

SENECA srl; Ta Ostiriya, 26 - 35127 - PADOVA - ITALY;
Tel. + 39.049.8705359 -
Fax +39.049.8706287

BAYANIN HULDA

Goyon bayan sana'a
support@seneca.it
Bayanin samfur
sales@seneca.it

Wannan takarda mallakar SENECA srl ce. An haramta kwafi da haɓakawa sai dai idan an ba da izini. Abubuwan da ke cikin wannan takarda ya dace da samfurori da fasaha da aka kwatanta. Za a iya gyara bayanan da aka bayyana ko ƙarawa don dalilai na fasaha da/ko tallace-tallace.

Takardu / Albarkatu

SENECA ZD-IN Shigarwar Dijital ko Modulolin fitarwa [pdf] Jagoran Jagora ZD-IN, Digital Input ko Output Modules, ZD-IN Digital Input ko Output Modules

Magana

• Manual mai amfani