Sunmi - logo

Sunmi V2S plus Smart Interactive Terminal - icon 1

QUICK START GUIDE T5F01

V2S பிளஸ் ஸ்மார்ட் இன்டராக்டிவ் டெர்மினல்

Sunmi V2S plus Smart Interactive Terminal - cover Sunmi V2S plus Smart Interactive Terminal - overview 1

விரைவு தொடக்கம்

  1. NFC ரீடர் (விரும்பினால்)
    லாயல்டி கார்டுகள் போன்ற NFC கார்டுகளைப் படிக்க.
  2. பிரிண்டர்
    சாதனம் இயக்கத்தில் இருக்கும் போது ரசீதுகளை அச்சிடுவதற்கு.
  3. ஸ்கேன் பட்டன்/எல்இடி (விரும்பினால்)
    Short press to enable barcode scanning function,
  4. வகை-சி
    சாதனம் சார்ஜிங் மற்றும் டெவலப்பர் பிழைத்திருத்தத்திற்கு.
  5. Micro 50 Card Slot/Nano SIM Card Slot
    மைக்ரோ எஸ்டி கார்டு மற்றும் நானோ சிம் கார்டை நிறுவுவதற்கு.
  6. முன் கேமரா (விரும்பினால்)
    வீடியோ கான்ஃபரன்ஸ் அல்லது புகைப்படம்/வீடியோ எடுப்பதற்கு.
  7. பவர் பட்டன்
    சுருக்கமாக அழுத்தவும்: திரையை எழுப்பவும், திரையைப் பூட்டவும்.
    Long press: long press for 2-3 seconds to turn on the device when it is off. Long press for 2-3 seconds to select to power off or reboot the device when it is on. Long press for 11 seconds to reboot a device when the system is frozen.
  8. வால்யூம் பட்டன்
    தொகுதி சரிசெய்தலுக்கு.
  9. ஸ்கேனர் (விரும்பினால்)
    பார்கோடு தரவு சேகரிப்புக்கு.
  10. பின்புற கேமரா
    புகைப்படம் எடுப்பதற்கும் விரைவான 1D/2D பார்கோடு வாசிப்புக்கும்.
  11. போகோ முள்
    பார்கோடு ஸ்கேனிங் துணை அல்லது தொடர்பு மற்றும் சார்ஜ் செய்வதற்கான தொட்டிலை இணைப்பதற்காக.
  12. PSAM அட்டை இடங்கள் (விரும்பினால்)
    PSAM கார்டுகளை நிறுவுவதற்கு.

அச்சிடும் வழிமுறைகள்

Sunmi V2S plus Smart Interactive Terminal - overview 2

இந்த சாதனம் 80மிமீ வெப்ப ரசீது அல்லது லேபிள் பேப்பர் ரோலை ஏற்ற முடியும், மேலும் கருப்பு லேபிளும் விருப்பமானது.
The paper roll spec is 79 plus/minus 0.5 * mm * emptyset50mm
Please press to open the printer (see ①). Please do not force open the printer to avoid printhead gear wear;
Load the paper into the printer and pull some paper outside the cutter following the direction shown in 2;
Close the cover to complete paper loading (see 3).
Notice: If the printer prints blank paper, please check whether the paper roll has been loaded in the correct direction.
Tips: To clean a label printhead, it is recommended to use a cotton swab dipped in alcohol or a alcohol prep pad (75% isopropyl alcohol) to wipe the printhead.

இந்த தயாரிப்பில் உள்ள நச்சு மற்றும் அபாயகரமான பொருட்களின் பெயர்கள் மற்றும் உள்ளடக்க அடையாளத்திற்கான அட்டவணை

பகுதி பெயர் நச்சு அல்லது அபாயகரமான பொருட்கள் மற்றும் கூறுகள்
Pb Hg Cd Cr (VI) பிபிபி PBDE DEHP DBP BBP டிஐபிபி
சர்க்யூட் போர்டு கூறு X 0 0 0 0 0 0 0 0 0
கட்டமைப்பு கூறு 0 0 0 0 0 0 0 0 0 0
பேக்கேஜிங் கூறு
.
0 0 0 0 0 0 0 0 0 0

O: கூறுகளின் அனைத்து ஒரே மாதிரியான பொருட்களிலும் உள்ள நச்சு மற்றும் அபாயகரமான பொருளின் உள்ளடக்கம் SJ/T 11363-2006 இல் குறிப்பிடப்பட்டுள்ள வரம்புக்குக் கீழே இருப்பதைக் குறிக்கிறது.
X: indicates that the content of the toxic and hazardous substance in at least one homogeneous material of the component exceeds the limit stipulated in Sj / T * 11363 – 2006 However, as for the reason, because there is no mature and replaceable technology in the industry at present.
சுற்றுச்சூழல் பாதுகாப்பு சேவை ஆயுளை எட்டிய அல்லது தாண்டிய தயாரிப்புகள் மின்னணு தகவல் தயாரிப்புகளின் கட்டுப்பாடு மற்றும் மேலாண்மை குறித்த விதிமுறைகளின்படி மறுசுழற்சி செய்யப்பட்டு மீண்டும் பயன்படுத்தப்பட வேண்டும், மேலும் அவை சீரற்ற முறையில் நிராகரிக்கப்படக்கூடாது.

அறிவிப்புகள்
பாதுகாப்பு எச்சரிக்கை
பவர் அடாப்டரின் குறிக்கப்பட்ட உள்ளீட்டுடன் தொடர்புடைய ஏசி சாக்கெட்டுடன் ஏசி பிளக்கை இணைக்கவும்;
காயத்தைத் தவிர்க்க, அங்கீகரிக்கப்படாத நபர்கள் பவர் அடாப்டரைத் திறக்கக்கூடாது;
இது ஒரு கிளாஸ் ஏ தயாரிப்பு. இந்த தயாரிப்பு வாழ்க்கை சூழலில் ரேடியோ குறுக்கீட்டை ஏற்படுத்தலாம்.
அந்த வழக்கில், குறுக்கீட்டிற்கு எதிராக பயனர் போதுமான நடவடிக்கைகளை எடுக்க வேண்டியிருக்கும்.
பேட்டரி மாற்று:
1.Explosion danger may arise if replacing with the wrong battery
2.The replaced battery shall be disposed of by maintenance personnel, and please do not throw it into fire

குறிப்பிடத்தக்க பாதுகாப்பு வழிமுறைகள்
மின்னல் அதிர்ச்சியின் சாத்தியமான அபாயங்களைத் தவிர்க்க மின்னல் புயல்களின் போது சாதனத்தை நிறுவவோ பயன்படுத்தவோ வேண்டாம்;
அசாதாரண துர்நாற்றம், வெப்பம் அல்லது புகையை நீங்கள் கண்டால், உடனடியாக மின்சக்தியை அணைக்கவும்;
The paper cutter is sharp, please do not touch

பரிந்துரைகள்
டெர்மினலில் திரவம் விழுவதைத் தடுக்க, நீர் அல்லது ஈரப்பதத்திற்கு அருகில் உள்ள முனையத்தைப் பயன்படுத்த வேண்டாம்;
மிகக் குளிர்ச்சியான அல்லது வெப்பமான சூழல்களில் முனையத்தைப் பயன்படுத்த வேண்டாம், அதாவது அருகில் தீப்பிழம்புகள் அல்லது எரியும் சிகரெட்டுகள்;
சாதனத்தை கைவிடவோ, வீசவோ அல்லது வளைக்கவோ வேண்டாம்;
Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal; Please do not use the terminal near medical equipment without permission.

அறிக்கைகள்
பின்வரும் செயல்களுக்கான பொறுப்புகளை நிறுவனம் ஏற்காது:
Damages caused by use and maintenance without complying with the conditions specified in this guide; The Company will not assume any responsibilities for the damages or problems caused by optional items or consumables (rather than the initial products or approved products of the Company). The customer is not entitled to change or modify the product without our consent. The product’s operating system supports official system up-dates, but if you change the operating system into a third party ROM system or alter the system fileசிஸ்டம் கிராக்கிங் மூலம், இது கணினி உறுதியற்ற தன்மை மற்றும் பாதுகாப்பு அபாயங்கள் மற்றும் அச்சுறுத்தல்களை ஏற்படுத்தலாம்.

மறுப்பு
As a result of product upgrading, some details in this document may not match the product, and the actual product shall govern. The Company reserves the right of interpretation of this document. The Company also reserves the right toalter this specification without prior notice.

ஐரோப்பிய ஒன்றிய ஒழுங்குமுறை இணக்கம்
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU. The description of accessories and components, including software, which allow the radio equipment to operate as intended, can be obtained in the full text of the EU declaration of conformity is available at the following internet address: https://developer.sunmi.com/docs/read/en-US/maaeghjk480

பயன்பாட்டிற்கான கட்டுப்பாடுகள்
This product may be used in the following European member states subject to the following restrictions. For products that operate in the frequency band 5150-5350MHz and 5945-6425 MHz (If the product support 6e), wireless access systems (WAS), including radio local area networks (RLANs), shall be restricted to indoor use.
Sunmi V2S plus Smart Interactive Terminal - icon 2 EU Representative: SUNMI France SAS 186, avenue Thiers, 69006 Lyon, France
WEE-Disposal-icon.png இந்த சின்னம் என்பது சாதாரண வீட்டுக் கழிவுகளுடன் பொருட்களை அப்புறப்படுத்துவது தடைசெய்யப்பட்டுள்ளது என்பதாகும். தயாரிப்பு வாழ்க்கைச் சுழற்சியின் முடிவில், கழிவு உபகரணங்களை ஒதுக்கப்பட்ட சேகரிப்புப் புள்ளிகளுக்கு எடுத்துச் செல்ல வேண்டும், புதிய தயாரிப்பை வாங்கும் போது விநியோகஸ்தரிடம் திரும்பப் பெற வேண்டும் அல்லது WEEE மறுசுழற்சி பற்றிய விரிவான தகவலுக்கு உங்கள் உள்ளூர் அதிகாரியைத் தொடர்புகொள்ளவும்.

Sunmi V2S plus Smart Interactive Terminal - icon 3 AT BE BG HR CY CZ .
DK
EE Fl FR DE EL HU IE
IT LV LT LU MT NL PL
PT PO SK SI ES SE யுகே(என்ஐ)
IS LI எண் CH TR
Note: In all EU member states, operation of 5150-5350MHz and 5945-6425MHz (If the product support 6e) restricted to indoor use only.

RF வெளிப்பாடு அறிக்கை (SAR)
இந்த கருவி கட்டுப்பாடற்ற சூழலுக்காக அமைக்கப்பட்டுள்ள ஐரோப்பிய ஒன்றிய கதிர்வீச்சு வெளிப்பாடு வரம்புகளுக்கு இணங்குகிறது.
SUNMI பற்றிய வழிமுறைகளைப் பார்க்கவும். webகுறிப்பிட்ட மதிப்புகளுக்கான தளம்.

ஐரோப்பிய ஒன்றியத்திற்கான அதிர்வெண் மற்றும் சக்தி:
SUNMI பற்றிய வழிமுறைகளைப் பார்க்கவும். webகுறிப்பிட்ட மதிப்புகளுக்கான தளம்.

இசைக்குழு அதிர்வெண் சக்தி (dBm)
ஜிஎஸ்எம் 900 880-915 34
டிசிஎஸ் 1800 1710-1785 31
WCDMA இசைக்குழு I 1920-1980 24
WCDMA இசைக்குழு VIII 880-915 24
LTE பேண்ட் 1 1920-1980 25
LTE பேண்ட் 3 1710-1785 25
LTE பேண்ட் 7 2500-2570 24.5
LTE பேண்ட் 8 880-915 25
LTE பேண்ட் 20 832-862 25
LTE பேண்ட் 28 703-748 23
LTE பேண்ட் 38 2570-2620 25
LTE பேண்ட் 40 2300-2400 25
BT 2402-2480 9.39
BLE 2402-2480 5.34
WLAN 2412-2472 17.55
WLAN 5150-5350 15.98
WLAN 5470-5725 15.54
WLAN 5725-5850 13.02
GNSS 1559-1610
NFC 13.56 42.45dBμV/மீ@10மீ

ISED கனடா இணக்க அறிக்கைகள்
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this devi must accept any interference, including interference that may cause undesired operation of the device. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

FCC இணக்க அறிக்கைகள்

இந்த சாதனம் FCC விதிகளின் பகுதி 15 உடன் இணங்குகிறது. செயல்பாடு பின்வரும் இரண்டு நிபந்தனைகளுக்கு உட்பட்டது: (1) இந்த சாதனம் தீங்கு விளைவிக்கும் குறுக்கீட்டை ஏற்படுத்தாது, மேலும் (2) தேவையற்ற செயல்பாட்டை ஏற்படுத்தக்கூடிய குறுக்கீடு உட்பட பெறப்பட்ட எந்தவொரு குறுக்கீட்டையும் இந்த சாதனம் ஏற்க வேண்டும்.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • பெறும் ஆண்டெனாவை மாற்றியமைக்கவும் அல்லது இடமாற்றவும்.
  • உபகரணங்கள் மற்றும் ரிசீவர் இடையே பிரிவை அதிகரிக்கவும்.
  • ரிசீவர் இணைக்கப்பட்டுள்ள சுற்றுவட்டத்திலிருந்து வேறுபட்ட ஒரு அவுட்லெட்டில் உபகரணங்களை இணைக்கவும்.
  • உதவிக்கு டீலர் அல்லது அனுபவம் வாய்ந்த ரேடியோ/டிவி தொழில்நுட்ப வல்லுநரை அணுகவும்.

எச்சரிக்கை: இணக்கத்திற்குப் பொறுப்பான தரப்பினரால் வெளிப்படையாக அங்கீகரிக்கப்படாத மாற்றங்கள் அல்லது மாற்றங்கள் சாதனத்தை இயக்குவதற்கான பயனரின் அதிகாரத்தை ரத்து செய்யக்கூடும் என்று பயனர் எச்சரிக்கப்படுகிறார்.

உற்பத்தி
ஷாங்காய் சன்மி டெக்னாலஜி கோ., லிமிடெட்.
அறை 505, KIC பிளாசா, எண்.388 சாங் ஹு சாலை, யாங் பு மாவட்டம், ஷாங்காய், சீனா

ஆவணங்கள் / ஆதாரங்கள்

Sunmi V2S plus Smart Interactive Terminal [pdf] பயனர் கையேடு
T5F01N, 2AH25T5F01N, V2S plus Smart Interactive Terminal, V2S plus, Smart Interactive Terminal, Interactive Terminal, Terminal

குறிப்புகள்

கருத்து தெரிவிக்கவும்

உங்கள் மின்னஞ்சல் முகவரி வெளியிடப்படாது. தேவையான புலங்கள் குறிக்கப்பட்டுள்ளன *