Boemo bo Bontshang
Molaoli LFC128-2
TATAISO EA MOSEBETSI BAKENG SA MOLAOLI OA LETEMO LFC128-2
LFC128-2-MN-EN-01 JUN-2020

LFC128-2 Selaoli sa Pontšo sa Boemo bo Phahameng

Tokomane ena e sebelisoa bakeng sa lihlahisoa tse latelang

SKU	LFC128-2	HW Ver.	1.0	FW Ver.	1.1
Ntho Code	LFC128-2	Boemo bo Bontšang Taolo, 4AI/DI, 4DI, 4xRelay, 1xPulse Output, 2 x RS485/ModbusRTU-Puisano ea Makhoba

Mesebetsi Fetola Log

HW Ver.	FW Ver.	Letsatsi la ho nšoa	Mesebetsi Fetola
1.0	1.1	PHUPTJANE-2020

Selelekela

LFC128-2 ke taolo ea ponts'o ea boemo bo holimo. Sehlahisoa se kopanya segokanyimmediamentsi sa Modbus RTU ho thusa PLC / SCADA / BMS mme boema-kepe bofe kapa bofe ba IoT bo ka hokela ho beha leihlo. LFC128-2 e na le moralo o bonolo empa o le matla o nang le 4 AI / DI, 4 DI, 4 Relays, 1 Pulse pulse output, 2 RS485 Slave ModbusRTU e ba lumellang hore ba hokahane le lisebelisoa tse ngata habonolo. Ka theknoloji e tsoetseng pele e fanang ka botsitso bo phahameng le ho tšepahala, mesebetsi e mengata, ho kenya habonolo ka skrine ea ho ama le segokanyimmediamentsi sa sebolokigolo se thusa ho bona boemo ba leihlo.

Tlhaloso

Lisebelisoa tsa Dijithale	04 x Ports, opto-coupler, 4.7 kohms input resisstance, 5000V rms isolation, Logic 0 (0-1VDC), Logic 1 (5-24VDC), Mesebetsi: logic status 0/1 kapa Pulse counting (32 bit counter with max 4kHz pulse)
Lisebelisoa tsa Analog	04 x Ports, khetha pakeng tsa 0-10VDC input kapa 0-20mA input, 12 bit Resolution, e ka hlophisoa e le Digital input by DIP switch (max 10VDC input) The AI1 port ke 0-10 VDC / 4-20 mA level connection port port
Relay Output	04 x Ports, electro-mechanical Relays, SPDT, tekanyo ea ho ikopanya 24VDC / 2A kapa 250VAC / 5A, matšoao a LED
Sephetho sa Pulse	01 x Ports, open-collector, opto-isolation, max 10mA le 80VDC, On/off control, Pulser (max 2.5Khz, max 65535 Pulses) kapa PWM (max 2.5Khz)
Puisano	02 x ModbusRTU-Slave, RS485, lebelo la 9600 kapa 19200, pontšo ea LED
Seta botjha konopo	Bakeng sa ho seta boema-kepe ba 02 x RS485 boema-kepe ho maemo a kamehla (9600, None parity, 8 bit)
Mofuta oa skrine	Skrine se thetsoang
Phepelo ea motlakase	9..36VDC
Tshebediso	200mA @ 24VDC phepelo
Mofuta oa ho kenya	Sekhahla sa phanele
Thibelo ea Terminal	sekontiri sa 5.0mm, tekanyo ea 300VAC, boholo ba terata 12-24AWG
Sebetsa mocheso / mongobo	0..60 degC / 95%RH e sa fokotseng
Boemo	H93xW138xD45
Boima bo kahare	390 dikgerama

Litšoantšo tsa lihlahisoa

Molao-motheo oa Ts'ebetso

5.1 puisano ea Modbus

02 x RS485/ModbusRTU-Lekhoba
Tsamaiso: Modbus RTU
Aterese: 1 - 247, 0 ke aterese ea Phatlalatso
Sekhahla sa Baud: 9600 , 19200
Bonngoe: ha ho letho, e makatsang, esita le

• Letšoao la boemo ba LED:
• Led on: puisano ea modbus OK
• Led blinking: data e amohetseng empa puisano ea modbus e fosahetse, ka lebaka la tlhophiso e fosahetseng ea Modbus: aterese, baudrate
• E tlositsoe: LFC128-2 ha ea fumana data, hlahloba khokahano

Bangolisi ba Memmap
BALA e sebelisa taelo ea 03, NGOLA e sebelisa taelo ea 16
Tlhophiso ea kamehla:

• Aterese: 1
• Baudrate lekhoba 1: 9600
• Parity lekhoba 1: ha ho letho
• Baudrate lekhoba 2: 9600
• Parity lekhoba 2: ha ho letho

Ngoliso ea Modbus	Hex adr	# ea lirekoto	Tlhaloso	Range	Ea kamehla	Sebopeho	Thepa	Tlhaloso
0	0	2	lintlha tsa sesebelisoa		LFC1	khoele	Bala
8	8	1	DI1       DI2: boemo ba dijithale	0-1		uint8	Bala	H_byte: DI1 L_byte: DI2
9	9	1	DI3       DI4: boemo ba dijithale	0-1		uint8	Bala	H_byte: DI3 L_byte: DI4
10	A	1	EA-1-AI      AI2: boemo ba dijithale	0-1		uint8	Bala	H_byte: AI1 L_byte: AI2
11	B	1	EA-3-AI      AI4: boemo ba dijithale	0-1		uint8	Bala	H_byte: AI3 L_byte: AI4
12	C	1	AI1: boleng ba analog			uint16	Bala
13	D	1	AI2: boleng ba analog			uint16	Bala
14	E	1	AI3: boleng ba analog			uint16	Bala
15	F	1	AI4: boleng ba analog			uint16	Bala
16	10	2	AI1: boleng bo lekantsoeng			phaphametse	Bala
18	12	2	AI2: boleng bo lekantsoeng			phaphametse	Bala
20	14	2	AI3: boleng bo lekantsoeng			phaphametse	Bala
22	16	2	AI4: boleng bo lekantsoeng			phaphametse	Bala
24	18	1	rela 1	0-1		uint16	Bala
25	19	1	rela 2	0-1		uint16	Bala
26	1A	1	rela 3	0-1		uint16	Bala
27	1B	1	rela 4	0-1		uint16	Bala
28	1C	1	bula mokelli ctrl		0-3	uint16	Bala/Ngola	0: theoha 1: ka 2: pwm, pulse ka ho tsoelang pele 3: pulse, ha palo ea pulse e lekaneng, ctrl = 0
30	1E	2	counter DI1			uint32	Bala/Ngola	khaonta e ngoloang, e ka hlakolehang
32	20	2	counter DI2			uint32	Bala/Ngola	khaonta e ngoloang, e ka hlakolehang
34	22	2	counter DI3			uint32	Bala/Ngola	khaonta e ngoloang, e ka hlakolehang
36	24	2	counter DI4			uint32	Bala/Ngola	khaonta e ngoloang, e ka hlakolehang
38	26	2	k'hamphani ea AI1			uint32	Bala/Ngola	counter e ngoloang, e ka hlakoleha, maqhubu a maholo a 10Hz
40	28	2	k'hamphani ea AI2			uint32	Bala/Ngola	counter e ngoloang, e ka hlakoleha, maqhubu a maholo a 10Hz
42	2A	2	k'hamphani ea AI3			uint32	Bala/Ngola	counter e ngoloang, e ka hlakoleha, maqhubu a maholo a 10Hz
44	2C	2	k'hamphani ea AI4			uint32	Bala/Ngola	counter e ngoloang, e ka hlakoleha, maqhubu a maholo a 10Hz
46	2E	2	DI1: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
48	30	2	DI2: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
50	32	2	DI3: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
52	34	2	DI4: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
54	36	2	AI1: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
56	38	2	AI2: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
58	3A	2	AI3: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
60	3C	2	AI4: nako e ntse e tsoela pele			uint32	Bala/Ngola	mots
62	3E	2	DI1: nako ea phomolo			uint32	Bala/Ngola	mots
64	40	2	DI2: nako ea phomolo			uint32	Bala/Ngola	mots
66	42	2	DI3: nako ea phomolo			uint32	Bala/Ngola	mots
68	44	2	DI4: nako ea phomolo			uint32	Bala/Ngola	mots
70	46	2	AI1: nako ea phomolo			uint32	Bala/Ngola	mots
72	48	2	AI2: nako ea phomolo			uint32	Bala/Ngola	mots
74	4A	2	AI3: nako ea phomolo			uint32	Bala/Ngola	mots
76	4C	2	AI4: nako ea phomolo			uint32	Bala/Ngola	mots
128	80	2	counter DI1			uint32	Bala	counter ha e khone ho ngola, hlakola
130	82	2	counter DI2			uint32	Bala	counter ha e khone ho ngola, hlakola
132	84	2	counter DI3			uint32	Bala	counter ha e khone ho ngola, hlakola
134	86	2	counter DI4			uint32	Bala	counter ha e khone ho ngola, hlakola
136	88	2	k'hamphani ea AI1			uint32	Bala	counter ha e khone ho ngola, ho hlakola; maqhubu a phahameng 10Hz
138	8A	2	k'hamphani ea AI2			uint32	Bala	counter ha e khone ho ngola, ho hlakola; maqhubu a phahameng 10Hz
140	8C	2	k'hamphani ea AI3			uint32	Bala	counter ha e khone ho ngola, ho hlakola; maqhubu a phahameng 10Hz
142	8E	2	k'hamphani ea AI4			uint32	Bala	counter ha e khone ho ngola, ho hlakola; maqhubu a phahameng 10Hz
256	100	1	modbus aterese lekhoba	1-247	1	uint16	Bala/Ngola
257	101	1	modbus baudrate lekhoba 1	0-1	0	uint16	Bala/Ngola	0: 9600, 1: 19200
258	102	1	modbus parity lekhoba 1	0-2	0	uint16	Bala/Ngola	0: ha ho letho, 1: e makatsang, 2: e lekana

5.2 Konopo ya ho seta botjha
Ha u tšoere konopo ea reset bakeng sa metsotsoana ea 4, LFC 128-2 e tla tsosolosa tlhophiso ea kamehla ho 02 x RS485 / Modbus.
RTU-Lekhoba.
Tlhophiso ea kamehla ea Modbus RTU:

• Aterese: 1
• Lebelo la Baud: 9600
• Parity: ha ho letho

Ho kenya ka dijithale

Tlhaloso:

• 04 likanale DI, tse arohaneng
• Ho Kena: 4.7 kΏ
• Ho itšehla thajana Voltage: 5000Vrms
• Boemo ba kelello 0: 0-1V
• Boemo ba kelello 1: 5-24V
• Mosebetsi:
• Bala logic 0/1
• Pulse Counter

5.3.1 Bala boemo bo utloahalang 0/1
Boleng ba kelello ho 'Mapa oa Memori oa Modbus: 0-1
Ngoliso ho boloka boleng ba logic ho 'Mapa oa Memori oa Modbus:

• DI1__DI2: boemo ba dijithale: e boloka boemo bo utloahalang ba kanale 1 le kanale 2.
  H_byte: DI1
  L_byte: DI2
• DI3__DI4: boemo ba dijithale: boloka boemo bo utloahalang ba kanale 3 le kanale 4.
  H_byte: DI3
  L_byte: DI4

5.3.2 Pulse Counter
Boleng ba Counter ho Modbus Memory Map, ha o eketsa nomoro e fetang moeli, e tla khutla ka bo eona: 0 4294967295 (32bits)
Rejisetara e bolokang boleng ba Counter ho 'Mapa oa Memori oa Modbus e ke ke ea hlakoloa:

• Counter DI1: e boloka boemo ba logic ba mocha oa 1
• Counter DI2: e boloka boemo ba logic ba mocha oa 2
• Counter DI3: boloka boemo ba logic ba mocha oa 3
• Counter DI4: e boloka boemo ba logic ba mocha oa 4
  Rejisetara e bolokang boleng ba Counter ho 'Mapa oa Memori oa Modbus e ke ke ea hlakoloa:
• Ha ho sesebelisoa sa ho seta bocha DI1: e boloka boemo ba logic ba mocha oa 1
• Ha ho sesebelisoa sa ho seta bocha DI2: e boloka boemo ba logic ba mocha oa 2
• Ha ho sesebelisoa sa ho seta bocha DI3: e boloka boemo ba logic ba mocha oa 3
• Ha ho sesebelisoa sa ho seta bocha DI4: e boloka boemo ba logic ba mocha oa 4

Pulse Counter Mode:
Palo ea lebelo le tlase e ka tlase ho 10Hz e nang le filthara, anti-jamming:

• Beha ngoliso ea "counter DI1: nako ea filthara" = 500-2000: Channel 1 e bala pulses ka tlase ho 10Hz
• Beha ngoliso ea "counter DI2: nako ea filthara" = 500-2000: Channel 2 e bala pulses ka tlase ho 10Hz
• Beha ngoliso ea "counter DI3: nako ea filthara" = 500-2000: Channel 3 e bala pulses ka tlase ho 10Hz
• Beha ngoliso ea "counter DI4: nako ea filthara" = 500-2000: Channel 4 e bala pulses ka tlase ho 10Hz
• Palo ea lebelo le phahameng la lebelo le maqhubu a maholo a 2KHz ntle le sefe:
• Beha ngoliso ea "counter DI1: nako ea filthara" = 1: mocha oa 1 o bala likhahla ka Fmax = 2kHz
• Beha ngoliso ea "counter DI2: nako ea filthara" = 1: mocha oa 2 o bala likhahla ka Fmax = 2kHz
• Beha ngoliso ea "counter DI3: nako ea filthara" = 1: mocha oa 3 o bala likhahla ka Fmax = 2kHz
• Beha ngoliso ea "counter DI4: nako ea filthara" = 1: mocha oa 4 o bala likhahla ka Fmax = 2kHz

5.4 Kenyelletso ea Analoji

04 liteishene tsa AI, ha ho na ho itšehla thajana (AI1 ke 4-20mA / 0-5 VDC / 0-10 VDC level input input)

Sebelisa DIP SW ho hlophisa tlhahiso ea Analog: 0-10V, 0-20mA

Boleng	Mofuta oa AI
0	0-10 V
1	0-20 mA

Mofuta oa ho kenya:

• Lekanya voltagE: 0-10V
• Lekanya hona joale: 0-20mA
• Tlhophiso ea AI e bala boemo bo ts'oanang le ba DI, empa ha e khethollehe ka lebelo la pulse la 0-24V.

Kenyelletso ea ho kenya:

• Lekanya voltage: 320 kΏ
• Lekanya hona joale: 499 Ώ

5.4.1 Bala boleng ba Analoge
Qeto 12 likotoana
Non-linearity: 0.1%
Boleng ba Analog ho 'Mapa oa Memori oa Modbus: 0-3900
Ngoliso ea boleng ba analog 'mapeng oa Memory oa Modbus:

• AI1 boleng ba analog: boloka boleng ba Analog ea mocha oa 1
• AI2 boleng ba analog: e boloka boleng ba Analog ea mocha oa 2
• AI3 boleng ba analog: boloka boleng ba Analog ea mocha oa 3
• AI4 boleng ba analog: boloka boleng ba Analog ea mocha oa 4

5.4.2 Tlhophiso ea AI e sebetsa joalo ka DI
Ha ho ho itšehla thajana
AI Configure AI ho bala boemo ba kelello bo ts'oanang le ba DI ka pulse ampmatla ho tloha 0-24V
Ho na le 2 counter threshold AIx: logic threshold 0 le counter AIx: threshold logic 1 tafoleng ea modbus: 0-4095

• Boleng ba Analog ea AI
• Analog boleng ba Analog ea AI> counter AIx: threshold logic 1: e nkoa e le Logic 1 boemo ba AI
• Counter AIx: threshold logic 0 =

Logic Boemo ba boemo bo utloahalang ba AI tafoleng ea Memory Memory ea Modbus: 0-1
Rejiseta e boloka boleng bo utloahalang ho 'Mapa oa Memory oa Modbus:

• AI1___AI2: boemo ba digital: e boloka boemo bo utloahalang ba mocha oa 1 le mocha oa 2.
  H_byte: AI1
  L_byte: AI2
• AI3___AI4: boemo ba digital: e boloka boemo bo utloahalang ba mocha oa 1 le mocha oa 2.
  H_byte: AI3
  L_byte: AI4

5.4.3 Pulse Counter AI max 10Hz
Boleng ba Counter ho Modbus Memory Map, ha o eketsa nomoro ho feta moeli, e tla khutla ka bo eona: 0 4294967295 (32bits)
Rejisetara e bolokang boleng ba Counter ho 'Mapa oa Memori oa Modbus e ke ke ea hlakoloa:

• Counter AI1: e boloka boemo ba logic ba mocha oa 1
• Counter AI2: boloka boemo ba logic ba mocha oa 2
• Counter AI3: boloka boemo ba logic ba mocha oa 3
• Counter AI4: boloka boemo ba logic ba mocha oa 4
  Rejisetara e bolokang boleng ba Counter ho 'Mapa oa Memori oa Modbus e ke ke ea hlakoloa:
• Ha ho reset counter AI1: e boloka boemo ba logic ba mocha oa 1
• Ha ho reset counter AI2: e boloka boemo ba logic ba mocha oa 2
• Ha ho reset counter AI3: e boloka boemo ba logic ba mocha oa 3
• Ha ho na reset counter AI4: boloka boemo ba logic ba mocha oa 4

5.5 Lesokoana

04 kanale Relay SPDT NO / NC
Tekanyetso ea ho ikopanya: 2A / 24VDC, 0.5A / 220VAC
Ho na le li-LED tsa maemo:

• Led on: Ikopanye le Haufi
• Led off: Bula Contact

Ngoliso ea kamehla ea Relay	Boemo ba li-relay ha u tsosolosa lisebelisoa tsa motlakase
3	Sebetsa ho latela tlhophiso ea Alamo

Tlhophiso ea alamo:

• HIHI : Relay 4 On
• HI : Relay 3 On
• LO : Relay 2 On
• LOLO: Relay 1 On

5.6 Pulse Output

01 mocha o ikhethileng oa pokello
Opto-coupler: Mohloli oa hona joale oa Imax = 10mA, Vceo = 80V
Mesebetsi: Bulela / E tima, jenereithara ea pulse, PWM
5.6.1 Ts'ebetso ea ho Bula/Ho tima
Beha rejisetara ea Open-collector tafoleng ea Memory Memory ea Modbus:

• Seta Rejisetara ea Mobokelli: 1 => Pulse Output ON
• Seta Rejisetara ea Mobokelli: 0 => Pulse Output OFF

5.6.2 Pul generator
Pulse output e fetisa boholo ba 65535 pulses, ka Fmax 2.5kHz
Hlophisa direjista tse latelang tafoleng ea Memory Map ea Modbus:

• Seta ngoliso ea "mokelli ea bulehileng: nomoro ea pulse": 0-65535 => Nomoro ea Pulse = 65535: phatlalatso ea 65535 pulse
• Beha ngoliso ea "mokelli ea bulehileng: potoloho ea nako": (0-65535) x0.1ms => Nako ea potoloho = 4: Fmax 2.5kHz
• Beha ngoliso ea "mokelli ea bulehileng: nako e ntse e tsoela pele": (0-65535) x0.1ms => Nako ea ho Bula: ke nako ea logic ea 1 ea pulse
• Beha ngoliso ea "moqokelli ea bulehileng ctrl" = 3 => lokisa Pulse Output ho hlahisa pulse le ho qala ho otla, ho hlahisa palo e lekaneng ea li-pulse ho "mokelli ea bulehileng: nomoro ea pulse" => emisa jenereithara ea pulse le ngoliso "mokelli ea bulehileng ctrl ”= 0

5.6.3 PWM
Maqhubu a phahameng ke 2.5kHz
Hlophisa direjista tse latelang tafoleng ea Memory Map ea Modbus:

• Beha ngoliso ea "mokelli ea bulehileng ctrl" = 2 => lokisa ts'ebetso ea Pulse Output PWM
• Beha ngoliso ea "mokelli ea bulehileng: potoloho ea nako": (0-65535) x0.1ms => Nako ea potoloho = 4: Fmax 2.5kHz
• Beha ngoliso ea "mokelli ea bulehileng: nako e ntse e tsoela pele": (0-65535) x0.1ms => Nako ea ho Bula: ke nako ea logic ea 1 ea pulse

Ho kenya

6.1 Mokhoa oa ho kenya

6.2 Wiring e nang le Sensor ea Boemo

Tlhophiso

7.1 Screen ea lapeng

LITLHAKISO: Fetolela skrineng sa 2 ka lintlha tse felletseng
LITLHAHISO: Hlahisa Tlhokomeliso ea Boemo
LEHAE: Khutlela ho Skrine sa Lehae
TIISETSO. (Default Password: a): Eya ho Setting Screen
7.2 Ho beha skrine (Lekunutu la kamehla: a)
7.2.1 Skrine 1

Li-ADCs: Boleng ba lets'oao le tala la kanale AI1
Boemo (Yuniti): Boemo bo lumellana le lets'oao la ADC kamora ho hlophisoa
Boemo ba Libaka tsa Decimal:Nomoro ea decimal ea linomoro ka mor'a letheba la Mohato 0-3 (00000, 1111.1, 222.22, 33.333)
Boemo ba yuniti: likarolo tsa boemo, 0-3 (0: mm, 1: cm, 2: m, 3: inch)
Ho 1Kenya boleng ba ADC kamora ho kenya 4 mA / 0 VDC ho AI1 bakeng sa ho lekanya boemong ba 0
Sekala 1: Boleng ba boemo bo bontšitsoeng bo lumellana le boleng bo kentsoeng ho 1 (hangata 0)
Ho 2Kenya boleng ba ADC kamora ho kenya 20 mA / 10 VDC ho AI1 bakeng sa ho lekanya maemong a felletseng
Sekala 2: Boleng ba boemo bo bontšitsoeng bo lumellana le boleng bo kentsoeng ho 2
Boemo ba Span: Boleng bo phahameng ba Boemo (Span Level ≥ Scale 2)
Bolumo ea Libaka tsa Decimal: Nomoro ea decimal ea linomoro ka mor'a letheba la Bolumo 0-3 (00000, 1111.1, 222.22, 33.333)
Bolumo ea Yuniti: likarolo tsa bophahamo ba 0-3 (0: lit, 1: cm, 2: m3, 3:%)
7.2.2 Skrine 2

Boemo ba Boemo ba Hi Hi Set (Uniti): Boemo bo phahameng ba Alarm Level
Level Hi Hys (Uniti): Boemo bo phahameng ba hysteresis ea Boemo ba Alamo
Boemo ba Boemo ba Hisete (Uniti): Boemo bo phahameng ba Boemo ba Alamo
Level Hi Hys (Yuniti): Boemo bo phahameng ba hysteresis ea Alarm Level
Boemo ba Lebelo la Seta (Uniti): Boemo bo tlase ba Boemo ba Alamo
Level Lo Hys (Uniti): Boemo bo tlase ba hysteresis ea Boemo ba Alamo
Boemo ba Lo Lo Set ntlha (Uniti): Boemo bo tlase ba Boemo ba Alamo
Level Lo Lo Hys (Uniti): Boemo bo tlase bo tlase ba Boemo ba Alamo
Mokhoa oa Alamo: 0: Boemo, 1: Bolumo
Bolumo ea Span(Yuniti): Boholo ba boleng ba molumo
7.2.3 Skrine 3

Volume Hi Hi Set ntlha (Uniti): Molumo o phahameng o phahameng oa Alarm Volume
Volume Hi Hi Hys (Uniti): Molumo o phahameng oa hysteresis oa Alarm Volume
Volume Hi Set ntlha (Yuniti): Molumo o phahameng oa Alarm Volume
Volume Hi Hys (Uniti): Molumo o phahameng oa hysteresis oa Alarm Volume
Bolumo Lo Setha ntlha (Uniti): Molumo o tlase oa Molumo oa Alamo
Bolumo ea Lo Hys (Uniti): Molumo o tlase oa hysteresis oa Alarm Volume
Bolumo ea Lo Lo Set ntlha (Uniti): Molumo o tlase o tlase oa Molumo oa Alamo
Bolumo ea Lo Lo Hys (Uniti): Molumo o tlase o tlase oa Molumo oa Alarm
Kakaretso ea ho Matha: Kenya ts'ebetso eohle. 0-1 (0: Che 1: E)
7.2.4 Skrine 4

Ho Tlatsa (Yuniti): Kakaretso ea mosebetsi: kakaretso e kentsoeng ka tanka
Tšebeliso (Yuniti): Mosebetsi oohle: tšebeliso eohle ea tanka
Kakaretso ea Libaka: Nomoro ea Decimal ea li-parameter Ho Tlatsa, Tšebeliso, Ho Tlatsa NRT, Tšebeliso ea NRT leqepheng la pontšo (eseng leqephe la litlhophiso)
Kakaretso ea Delta (Yuniti): Boemo ba hysteresis ea ts'ebetso eohle
Aterese ea Modbus: Aterese ea Modbus ea LFC128-2, 1-247
Modbus Baurate S1: 0-1 (0 : 9600 , 1 : 19200)
Modbus Parity S1: 0-2 (0: ha ho le ea mong, 1: e makatsang, 2: e lekana)
Modbus Baurate S2: 0-1 (0 : 9600 , 1 : 19200)
Modbus Parity S2: 0-2 (0: ha ho le ea mong, 1: e makatsang, 2: e lekana)
Palo ea Lintlha: Palo ea lintlha ka har'a tafole ho fetolela ho tloha boemong ho ea ho bophahamo, 1-166
7.2.5 Skrine 5

Ntlha ea 1 (Boemo ba Boemo): Boemo ho Ntlha ea 1
Molumo oa Ntlha ea 1 (Molumo oa Molumo): Molumo o lumellanang le Ntlha ea 1
Mohato oa 166 (Level Unit): Boemo ba mafura sebakeng sa 166
Molumo oa Ntlha ea 166 (Molumo oa Molumo): Molumo o lumellanang le Ntlha ea 166
7.2.6 Skrine 6

Lekunutu: Password ho kenya Leqephe la ho Seta, litlhaku tse 8 tsa ASCII
Lebitso la Tanka: Lebitso la tanka le hlaha skrineng se seholo

Ho batle phoso

Che.	Phenomena	Lebaka	Litharollo
1	Modbus e hlolehile ho buisana	Boemo ba LED ea Modbus: LED e koetsoe: ha e fumanehe data LED ea panya: tlhophiso ea Modbus ha e nepahale.	Lekola khokahano Lekola tlhophiso ea Modbus: Aterese, Baud Rate, Parity
2	Timeout Modbus	Lerata le hlaha moleng	Hlophisa Baudrate 9600 'me u sebelise thapo e sothehileng e nang le tšireletso e thibelang ho jamming
3	Sensor e Khaotsoe	Sensor le LFC128 li lahlehetsoe ke khokahano	Ho hlahloba khokahano Lekola mofuta oa sensor (LFC128-2 e hokahana feela le 0-10VDC / 4- 20mA mofuta oa sensor ea analog) Lekola switch ho bona hore na e buletsoe ka nepo Sheba hore sehokelo sa sensor se nepahetse AI1
4	Phoso ea tafole ea linearization	Phoso ea tafole ea ho fetolela ho tloha boemong ho ea ho bophahamo	Sheba tlhophiso ea tafole ea phetoho ho tloha boemong ho ea ho bophahamo

Mabitso a tšehetsang

Moetsi
Litlhaloso tsa likarolo tsa Daviteq Technologies Inc
No.11 Street 2G, Nam Hung Vuong Res., An Lac Ward, Binh Tan Dist., Ho Chi Minh City, Vietnam.
Tel: +84-28-6268.2523/4 (ext.122)
Lengolo-tsoibila: info@daviteq.com
www.daviteq.com

Litokomane / Lisebelisoa

daviteq LFC128-2 Taolo ea Pontšo ea Boemo bo Phahameng [pdf] Buka ea Taelo LFC128-2, LFC128-2 Selaoli sa Pontšo sa Maemo a Tsoetseng Pele, Taolo ea Pontšo ea Maemo a Tsoetseng Pele, Taolo ea Pontšo ea Boemo, Selaoli sa Pontšo.

Litšupiso

• Bukana ea Mosebelisi