Level Indicating
Controller LFC128-2
USER GUIDE FOR LEVEL INDICATING CONTROLLER LFC128-2
LFC128-2-MN-EN-01 JUN-2020

LFC128-2 Babban Mai Kula da Nuni Matsayi

Ana amfani da wannan takaddar don samfuran masu zuwa

SKU	Saukewa: LFC128-2	HW Ver.	1.0	FW Ver.	1.1
Lambar Abu	Saukewa: LFC128-2	Level Indicating Controller, 4AI/DI, 4DI, 4xRelay, 1xPulse Output, 2 x RS485/ModbusRTU-Slave Communication

Canje-canje Log ɗin Ayyuka

HW Ver.	FW Ver.	Ranar Saki	Ayyuka Canza
1.0	1.1	JUN-2020

Gabatarwa

LFC128-2 is an advanced level display controller. The product integrates Modbus RTU interface to help PLC / SCADA / BMS and any IoT port can connect to monitor. LFC128-2 has a simple yet powerful design with 4 AI / DI, 4 DI, 4 Relays, 1 Pulse pulse output, 2 RS485 Slave ModbusRTU allowing them to connect with multiple devices easily. With advanced technology that provides high stability and reliability, many functions, easy installation with touch screen and friendly interface helps visually monitor level.

Ƙayyadaddun bayanai

Abubuwan Shiga na Dijital	04 x Ports, opto-coupler, 4.7 kohms input resisrtance, 5000V rms isolation, Logic 0 (0-1VDC), Logic 1 (5-24VDC), Functions: logic status 0/1 or Pulse counting (32 bit counter with max 4kHz pulse)
Abubuwan Analog	04 x Ports, select between 0-10VDC input or 0-20mA input, 12 bit Resolution, can be configured as Digital input by DIP switch (max 10VDC input) The AI1 port is a 0-10 VDC / 4-20 mA level sensor connection port
Fitowar Relay	04 x Ports, electro-mechanical Relays, SPDT, contact rating 24VDC/2A or 250VAC/5A, LED indicators
Fitowar bugun jini	01 x Ports, open-collector, opto-isolation, max 10mA and 80VDC, On/off control, Pulser (max 2.5Khz, max 65535 Pulses) or PWM (max 2.5Khz)
Sadarwa	02 x ModbusRTU-Slave, RS485, speed 9600 or 19200, LED indicator
Maɓallin sake saiti	For resetting 02 x RS485 Slave port to default setting (9600, None parity, 8 bit)
Nau'in allo	Kariyar tabawa
Tushen wutan lantarki	9VDC
Amfani	200mA @ 24VDC supply
Nau'in hawa	Dutsen panel
Filin Garko	pitch 5.0mm, rating 300VAC, wire size 12-24AWG
Yin aiki da zafin jiki / zafi	0..60 degC / 95%RH non-condensing
Girma	H93xW138xD45
Cikakken nauyi	390g ku

Hotunan samfur

Ka'idar Aiki

5.1 Modbus sadarwa

02 x RS485/ModbusRTU-Slave
Ladabi: Modbus RTU
Adireshi: 1 – 247, 0 is the Broadcast address
Baud darajarku: 9600, 19200
Daidaitacce: babu, m, ko da

• Status indicator LED:
• Led on: modbus communication OK
• Led blinking: received data but modbus communication incorrect, due to wrong Modbus configuration: address, baudrate
• Led off: LFC128-2 received no data, check the connection

Memmap masu rijista
READ uses command 03, WRITE uses command 16
Tsari na asali:

• Adireshin: 1
• Baudrate slave 1: 9600
• Parity slave 1: none
• Baudrate slave 2: 9600
• Parity slave 2: none

Rajistar Modbus	Hex adr	# of registers	Bayani	Rage	Default	Tsarin	Dukiya	Sharhi
0	0	2	bayanin na'urar		LFC1	kirtani	Karanta
8	8	1	DI1       DI2: digital status	0-1		ciki8	Karanta	H_byte: DI1 L_byte: DI2
9	9	1	DI3       DI4: digital status	0-1		ciki8	Karanta	H_byte: DI3 L_byte: DI4
10	A	1	Mai Rarraba AI1      AI2: digital status	0-1		ciki8	Karanta	H_byte: AI1 L_byte: AI2
11	B	1	Mai Rarraba AI3      AI4: digital status	0-1		ciki8	Karanta	H_byte: AI3 L_byte: AI4
12	C	1	AI1: analog value			ciki16	Karanta
13	D	1	AI2: analog value			ciki16	Karanta
14	E	1	AI3: analog value			ciki16	Karanta
15	F	1	AI4: analog value			ciki16	Karanta
16	10	2	AI1: scaled value			yi iyo	Karanta
18	12	2	AI2: scaled value			yi iyo	Karanta
20	14	2	AI3: scaled value			yi iyo	Karanta
22	16	2	AI4: scaled value			yi iyo	Karanta
24	18	1	relay 1	0-1		ciki16	Karanta
25	19	1	relay 2	0-1		ciki16	Karanta
26	1A	1	relay 3	0-1		ciki16	Karanta
27	1B	1	relay 4	0-1		ciki16	Karanta
28	1C	1	open collector ctrl		0-3	ciki16	Karanta/Rubuta	0: off 1: on 2: pwm, pulse continuously 3: pulse, when enough pulse number, ctrl = 0
30	1E	2	counter DI1			ciki32	Karanta/Rubuta	counter writable, erasable
32	20	2	counter DI2			ciki32	Karanta/Rubuta	counter writable, erasable
34	22	2	counter DI3			ciki32	Karanta/Rubuta	counter writable, erasable
36	24	2	counter DI4			ciki32	Karanta/Rubuta	counter writable, erasable
38	26	2	counter AI1			ciki32	Karanta/Rubuta	counter writable, erasable, max frequency 10Hz
40	28	2	counter AI2			ciki32	Karanta/Rubuta	counter writable, erasable, max frequency 10Hz
42	2A	2	counter AI3			ciki32	Karanta/Rubuta	counter writable, erasable, max frequency 10Hz
44	2C	2	counter AI4			ciki32	Karanta/Rubuta	counter writable, erasable, max frequency 10Hz
46	2E	2	DI1: time on			ciki32	Karanta/Rubuta	dakika
48	30	2	DI2: time on			ciki32	Karanta/Rubuta	dakika
50	32	2	DI3: time on			ciki32	Karanta/Rubuta	dakika
52	34	2	DI4: time on			ciki32	Karanta/Rubuta	dakika
54	36	2	AI1: time on			ciki32	Karanta/Rubuta	dakika
56	38	2	AI2: time on			ciki32	Karanta/Rubuta	dakika
58	3A	2	AI3: time on			ciki32	Karanta/Rubuta	dakika
60	3C	2	AI4: time on			ciki32	Karanta/Rubuta	dakika
62	3E	2	DI1: time off			ciki32	Karanta/Rubuta	dakika
64	40	2	DI2: time off			ciki32	Karanta/Rubuta	dakika
66	42	2	DI3: time off			ciki32	Karanta/Rubuta	dakika
68	44	2	DI4: time off			ciki32	Karanta/Rubuta	dakika
70	46	2	AI1: time off			ciki32	Karanta/Rubuta	dakika
72	48	2	AI2: time off			ciki32	Karanta/Rubuta	dakika
74	4A	2	AI3: time off			ciki32	Karanta/Rubuta	dakika
76	4C	2	AI4: time off			ciki32	Karanta/Rubuta	dakika
128	80	2	counter DI1			ciki32	Karanta	counter cannot write, erase
130	82	2	counter DI2			ciki32	Karanta	counter cannot write, erase
132	84	2	counter DI3			ciki32	Karanta	counter cannot write, erase
134	86	2	counter DI4			ciki32	Karanta	counter cannot write, erase
136	88	2	counter AI1			ciki32	Karanta	counter cannot write, erase; max frequency 10Hz
138	8A	2	counter AI2			ciki32	Karanta	counter cannot write, erase; max frequency 10Hz
140	8C	2	counter AI3			ciki32	Karanta	counter cannot write, erase; max frequency 10Hz
142	8E	2	counter AI4			ciki32	Karanta	counter cannot write, erase; max frequency 10Hz
256	100	1	modbus address slave	1-247	1	ciki16	Karanta/Rubuta
257	101	1	modbus baudrate slave 1	0-1	0	ciki16	Karanta/Rubuta	0: 9600, 1: 19200
258	102	1	modbus parity slave 1	0-2	0	ciki16	Karanta/Rubuta	0: babu, 1: m, 2: ko da

5.2 Maɓallin Sake saitin
When holding the reset button for 4 seconds, LFC 128-2 will reset the default configuration to 02 x RS485 / Modbus
RTU-Slave.
Default Modbus RTU Configuration:

• Adireshin: 1
• Farashin: 9600
• Paraty: babu

5.3 Shigarwar Dijital

Bayani:

• 04 channels DI, isolated
• Input Resistance: 4.7 kΏ
• Kadaici Voltage: 5000Vrm
• Logic level 0: 0-1V
• Logic level 1: 5-24V
• Aiki:
• Read logic 0/1
• Pulse Counter

5.3.1 Read the logical state 0/1
Logic value in Modbus Memory Map: 0-1
Registers to store logic values in the Modbus Memory Map:

• DI1__DI2: digital status: stores the logical state of channel 1 and channel 2.
  H_byte: DI1
  L_byte: DI2
• DI3__DI4: digital status: store the logical state of channel 3 and channel 4.
  H_byte: DI3
  L_byte: DI4

5.3.2 Pulse Counter
Counter value in Modbus Memory Map, when adding the number exceeds the threshold, it will automatically return: 0 4294967295 (32bits)
The register that stores Counter value in the Modbus Memory Map cannot be erased:

• Counter DI1: stores the logic state of channel 1
• Counter DI2: stores the logic state of channel 2
• Counter DI3: store the logic state of channel 3
• Counter DI4: stores the logic state of channel 4
  The register that stores Counter value in the Modbus Memory Map cannot be erased:
• None reset counter DI1: stores the logic state of channel 1
• None reset counter DI2: stores the logic state of channel 2
• None reset counter DI3: stores the logic state of channel 3
• None reset counter DI4: stores the logic state of channel 4

Pulse Counter Mode:
Low-speed pulse count less than 10Hz with filter, anti-jamming:

• Set register “counter DI1: filter time” = 500-2000: Channel 1 counts pulses less than 10Hz
• Set register “counter DI2: filter time” = 500-2000: Channel 2 counts pulses less than 10Hz
• Set register “counter DI3: filter time” = 500-2000: Channel 3 counts pulses less than 10Hz
• Set register “counter DI4: filter time” = 500-2000: Channel 4 counts pulses less than 10Hz
• High-speed pulse count with max 2KHz frequency without filter:
• Set register “counter DI1: filter time” = 1: channel 1 counts pulses with Fmax = 2kHz
• Set register “counter DI2: filter time” = 1: channel 2 counts pulses with Fmax = 2kHz
• Set register “counter DI3: filter time” = 1: channel 3 counts pulses with Fmax = 2kHz
• Set register “counter DI4: filter time” = 1: channel 4 counts pulses with Fmax = 2kHz

5.4 Analog Input

04 AI channels, no isolation (AI1 is a 4-20mA / 0-5 VDC / 0-10 VDC level sensor input )

Use DIP SW to configure Analog input: 0-10V, 0-20mA

Daraja	Type of AI
0	0-10 V
1	0-20 mA

Nau'in shigarwa:

• Auna voltagSaukewa: 0-10V
• Measure current: 0-20mA
• The configuration for AI reads the same logical state as DI, but it is not isolated with a pulse range of 0-24V

Rashin shigar da bayanai:

• Auna voltage: 320 kΏ
• Measure the current: 499 Ώ

5.4.1 Read the Analog value
Resolution 12 ragowa
Non-Linearity: 0.1%
Analog value in Modbus Memory Map: 0-3900
Analog value register in the Modbus Memory Map:

• AI1 analog value: store the Analog value of channel 1
• AI2 analog value: stores the Analog value of channel 2
• AI3 analog value: store the Analog value of channel 3
• AI4 analog value: store the Analog value of channel 4

5.4.2 AI configuration works as DI
Babu warewa
AI Configure AI to read the same logic state as DI with pulse amplitude from 0-24V
There are 2 counter threshold AIx: logic threshold 0 and counter AIx: threshold logic 1 in the modbus table: 0-4095

• Analog Analog value of AI <counter AIx: threshold logic 0: is considered Logic 0 status of AI
• Analog Analog value of AI> counter AIx: threshold logic 1: is considered to be Logic 1 state of AI
• Counter AIx: threshold logic 0 = <Analog value of AI <= counter AIx: threshold logic 1: is considered to be the constant logic state

Logic Logical status value of AI in Modbus Memory Map table: 0-1
The register stores logical values in Modbus Memory Map:

• AI1___AI2: digital status: stores the logical state of channel 1 and channel 2.
  H_byte: AI1
  L_byte: AI2
• AI3___AI4: digital status: stores the logical state of channel 1 and channel 2.
  H_byte: AI3
  L_byte: AI4

5.4.3 Pulse Counter AI max 10Hz
Counter value in Modbus Memory Map, when adding the number beyond the threshold, it will automatically return: 0 4294967295 (32bits)
The register that stores Counter value in the Modbus Memory Map cannot be erased:

• Counter AI1: stores the logic state of channel 1
• Counter AI2: save logic state of channel 2
• Counter AI3: save logic state of channel 3
• Counter AI4: save logic state of channel 4
  The register that stores Counter value in the Modbus Memory Map cannot be erased:
• None reset counter AI1: stores the logic state of channel 1
• None reset counter AI2: stores the logic state of channel 2
• None reset counter AI3: stores the logic state of channel 3
• None reset counter AI4: save logic state of channel 4

5.5 Mai watsa shiri

04 channel Relay SPDT NO / NC
Contact rating: 2A / 24VDC, 0.5A / 220VAC
There are status LEDs:

• Led on: Close Contact
• Led off: Open Contact

Default Relay Register	Status of relays when resetting power supplies
3	Operate according to the Alarm configuration

Kanfigareshin Ƙararrawa:

• HIHI : Relay 4 On
• HI : Relay 3 On
• LO : Relay 2 On
• LOLO: Relay 1 On

5.6 Fitar Pulse

01 isolated open-collector channel
Opto-coupler: Source current Imax = 10mA, Vceo = 80V
Ayyuka: On / Off, pulse generator, PWM
5.6.1 On/Off Function
Set the Open-collector register in the Modbus Memory Map table:

• Set Open-collector register: 1 => Pulse Output ON
• Set Open-collector register: 0 => Pulse Output OFF

5.6.2 Pulse generator
Pulse output transmits a maximum of 65535 pulses, with Fmax 2.5kHz
Configure the following registers in the Modbus Memory Map table:

• Set register “open collector: pulse number”: 0-65535 => Pulse Number = 65535: broadcast 65535 pulses
• Set register “open collector: time cycle”: (0-65535) x0.1ms => Time Cycle = 4: Fmax 2.5kHz
• Set register “open collector: time on”: (0-65535) x0.1ms => Time On: is the logic time 1 of the pulse
• Set the register “open collector ctrl” = 3 => configure the Pulse Output to generate a pulse and start to pulse, generate a sufficient number of pulses in the “open collector: pulse number” register => stop pulse generator and register ” open collector ctrl ”= 0

5.6.3 PWM
Max frequency 2.5kHz
Configure the following registers in the Modbus Memory Map table:

• Set the register “open collector ctrl” = 2 => configure Pulse Output PWM function
• Set register “open collector: time cycle”: (0-65535) x0.1ms => Time Cycle = 4: Fmax 2.5kHz
• Set register “open collector: time on”: (0-65535) x0.1ms => Time On: is the logic time 1 of the pulse

Shigarwa

6.1 Hanyar shigarwa

6.2 Wiring with Level Sensor

Kanfigareshan

7.1 Allon Gida

ALAMOMIN: Switch to 2nd screen with more detailed information
ALARAMMAN: Show Level Alert
HADA: Komawa allo na Gida
CONFIG. (Default Password: a): Go to Setting Screen
7.2 Setting screen (Default Password: a)
7.2.1 Layar 1

ADC: Raw signal value of channel AI1
Level (Unit): The level corresponds to the ADC signal after configuration
Decimal Places Level:Decimal number of digits after the dot of Level 0-3 (00000, 1111.1, 222.22, 33.333)
Unit level: level units, 0-3 (0: mm, 1: cm, 2: m, 3: inch)
A cikin 1: Enter the ADC value after putting 4 mA / 0 VDC into AI1 for calibration at 0 level
Sikeli 1: The level value displayed corresponds to the value entered in In 1 (usually 0)
A cikin 2: Enter the ADC value after putting 20 mA / 10 VDC into AI1 for calibration at Full level
Sikeli 2: The level value displayed corresponds to the value entered in In 2
Span Level: Maximum value of Level (Span Level ≥ Scale 2)
Decimal Places Volume: Decimal number of digits after the dot of Volume 0-3 (00000, 1111.1, 222.22, 33.333)
Unit Volume: units of volume 0-3 (0: lit, 1: cm, 2: m3, 3:%)
7.2.2 Layar 2

Level Hi Hi Set point (Unit): High High level of Alarm Level
Level Hi Hi Hys (Unit): High High level hysteresis of Alarm Level
Level Hi Set point (Unit): High level of Alarm Level
Level Hi Hys (Unit): High level hysteresis of Alarm Level
Level Lo Set point (Unit): Low level of Alarm Level
Level Lo Hys (Unit): Low level hysteresis of Alarm Level
Level Lo Lo Set point (Unit): Low Low level of Alarm Level
Level Lo Lo Hys (Unit): Low Low level hysteresis of Alarm Level
Yanayin ƙararrawa: 0: Level, 1: Volume
Span Volume(Unit): Maximum value of the volume
7.2.3 Layar 3

Volume Hi Hi Set point (Unit): High High volume of Alarm Volume
Volume Hi Hi Hys (Unit): High High volume hysteresis of Alarm Volume
Volume Hi Set point (Unit): High volume of Alarm Volume
Volume Hi Hys (Unit): High volume hysteresis of Alarm Volume
Volume Lo Set point (Unit): Low volume of Alarm Volume
Volume Lo Hys (Unit): Low volume hysteresis of Alarm Volume
Volume Lo Lo Set point (Unit): Low Low volume of Alarm Volume
Volume Lo Lo Hys (Unit): Low Low volume hysteresis of Alarm Volume
Run Total: Run the total function. 0-1 (0: No 1: Yes)
7.2.4 Layar 4

Filling (Unit): Total function: total put into tank
Consumption (Unit): Total function: total consumption of the tank
Decimal Places Total: Decimal number of parameters Filling, Consumption, NRT Filling, NRT Consumption on display page (not the setting page)
Delta Total (Unit): Hysteresis level of the total function
Adireshin Modbus: Modbus address of LFC128-2, 1-247
Modbus Baurate S1: 0-1 (0 : 9600 , 1 : 19200)
Modbus Parity S1: 0-2 (0: none, 1: odd, 2: even)
Modbus Baurate S2: 0-1 (0 : 9600 , 1 : 19200)
Modbus Parity S2: 0-2 (0: none, 1: odd, 2: even)
Num of Points: Number of points in the table to convert from level to volume, 1-166
7.2.5 Layar 5

Point 1 Level (Level Unit): Level at Point 1
Point 1 Volume (Volume Unit): The corresponding volume at Point 1
Point 166 Level (Level Unit): Fuel level at Point 166
Point 166 Volume (Volume Unit): The corresponding volume at Point 166
7.2.6 Layar 6

Kalmar wucewa: Password to enter the Setting page, 8 ASCII characters
Tank Name: Tank name displayed on the main screen

Shirya matsala

A'a.	Al'amura	Dalili	Magani
1	Modbus failed to communicate	Modbus LED Status: LED is off: received no data LED is blinking: the Modbus configuration is not the correct	Check the connection Check the Modbus configuration: Address, Baud Rate, Parity
2	Timeout Modbus	Noise appears on the line	Configure Baudrate 9600 and use a twisted pair cable with anti-jamming protection
3	An Kashe Haɗin Sensor	Sensor and LFC128 lost connection	Checking connection Check sensor type (LFC128-2 only connects to 0-10VDC / 4- 20mA analog sensor type) Check the switch to see if it is turned on correctly Check that the sensor connector is correct AI1
4	Linearization table error	Error of conversion table from level to volume	Check the configuration of the conversion table from level to volume

Goyan bayan lambobin sadarwa

Mai ƙira
Daviteq Technologies Inc. girma
No.11 Titin 2G, Nam Hung Vuong Res., An Lac Ward, Binh Tan Dist., Ho Chi Minh City, Vietnam.
Tel: +84-28-6268.2523/4 (ext.122)
Imel: info@daviteq.com
www.daviteq.com

Takardu / Albarkatu

daviteq LFC128-2 Advanced Level Display Controller [pdf] Jagoran Jagora LFC128-2, LFC128-2 Advanced Level Display Controller, Advanced Level Display Controller, Level Display Controller, Display Controller

Magana

• Manual mai amfani