LATTICE FPGA-UG-02042-26.4 Programming Cables

Disclaimers

Lattice haiite waranti, chinomiririra, kana vimbiso maererano nekurongeka kweruzivo rwuri mugwaro iri kana kukodzera kwezvigadzirwa zvayo kune chero chinangwa. Ruzivo rwese rwuri pano rwunopihwa AS IS uye nekukanganisa kwese, uye njodzi yese ine chekuita neruzivo rwakadai ndeyeMutengi. Mutengi haazovimbi nechero data uye maitiro ekuita kana ma parameter akapihwa pano. Zvigadzirwa zvinotengeswa neLattice zvave pasi pekuyedzwa kushoma uye ibasa reMutengi kuzvimiririra kuona kukodzera kwechero zvigadzirwa uye kuyedza nekuona zvakafanana. Hapana zvigadzirwa zveLattice zvinofanirwa kushandiswa pamwe chete nemishini- kana chengetedzo-yakakosha kana chero imwe application umo kutadza kwechigadzirwa cheLattice kunogona kugadzira mamiriro ezvinhu apo kukuvara kwemunhu, kufa, pfuma yakanyanya kana kukuvara kwezvakatipoteredza kunogona kuitika. Ruzivo rwunopihwa mugwaro iri nderweLattice Semiconductor, uye Lattice inochengetera kodzero yekuita chero shanduko kuruzivo rwuri mugwaro iri kana kune chero zvigadzirwa chero nguva pasina chiziviso.

Features

• Tsigiro kune ese Lattice programmable zvigadzirwa
  • 2.5 V kusvika 3.3 V I2C programming (HW-USBN-2B)
  • 1.2 V kusvika 3.3 VJTAG uye SPI programming (HW-USBN-2B)
  • 1.2 V kusvika 5 VJTAG uye SPI programming (mamwe tambo dzese)
  • Yakanakira dhizaini prototyping uye debugging
• Batanidza kune akawanda PC interfaces
  • USB (v.1.0, v.2.0)
  • PC Parallel Port
• Zviri nyore kushandisa zvirongwa zvekubatanidza
  • Zvinosiyana-siyana flywire, 2 x 5 (.100”) kana 1 x 8 (.100”) zvinobatanidza
  • 6 tsoka (2 metres) kana kupfuura yeprogramming cable kureba (PC kusvika kuDUT)
• Lead-isina/RoHS inoenderana nekuvaka

Programming Cables

Lattice Programming Cable zvigadzirwa ndeye hardware yekubatanidza ye-in-system programming yezvese Lattice zvishandiso. Mushure mekunge wapedza yako logic dhizaini uye gadzira chirongwa file neLattice Diamond®/ispLEVER® Classic yekuvandudza maturusi, unogona kushandisa Diamond Chirongwa kana ispVM™ System software kuronga zvishandiso pabhodhi rako. Iyo ispVM System/Diamond Programmer software inogadzira otomatiki mirairo yakakodzera yehurongwa, kero dzehurongwa uye data rekuronga zvinoenderana neruzivo rwakachengetwa muchirongwa. file uye ma parameter aunoisa muDiamond Programmer/ispVM System. Zviratidziro zvehurongwa zvinobva zvagadzirwa kubva ku USB kana parallel port yePC uye inotungamirwa kuburikidza netambo yekuronga kune mudziyo. Hapana zvimwe zvikamu zvinodiwa pakuronga.
Diamond Programmer/ispVM System software inosanganisirwa neese Lattice dhizaini maturusi zvigadzirwa uye inowanikwa kurodha kubva kuLattice. web site pa www.latticesemi.com/programmer.

Programming Cable Pin Definitions

Iwo mabasa anopihwa netambo dzehurongwa zvinoenderana neanowanikwa mabasa paLattice programmable zvishandiso. Sezvo mamwe maturusi ane akasiyana ehurongwa maficha, iwo chaiwo mabasa anopihwa netambo yekugadzira anogona kutsamira pane yakasarudzwa chinangwa mudziyo. ispVM System/Diamond Programmer software inogadzira otomatiki mabasa akakodzera zvichibva pane yakasarudzwa mudziyo. Ona Tafura 3.1 yekuwedzeraview yeiyo programming cable mabasa.
Tafura 3.1. Programming Cable Pin Definitions.

Programming Cable Pin	Zita	Programming Cable Pin Type	Tsanangudzo
VCC	Programming Voltage	Input	Batanidza kune VCCIO kana VCCJ ndege yechishandiso chinonangwa. Yakajairika ICC = 10 mA. The target board inopa VCC kugovera / referensi yetambo.
TDO/SO	Test Data Output	Input	Inoshandiswa kushandura data kunze kuburikidza neIEEE1149.1 (JTAG) programming standard.
TDI/SI	Test Data Input	Output	Inoshandiswa kushandura data mukati kuburikidza neIEEE1149.1 programming standard.
ISPEN/PROG	Enable	Output	Ita kuti mudziyo ugadziriswe. Zvakare inoshanda seSN/SSPI Chip Sarudza yeSPI programming neHW-USBN-2B.
TRST	Test Reset	Output	Optional IEEE 1149.1 state muchina reset.
ZVAITA	ZVAITA	Input	ZVAITA rinoratidza mamiriro ekugadzirisa
TMS	Test Mode Sarudza Input	Output	Inoshandiswa kudzora IEEE1149.1 state muchina.
GND	Ground	Input	Batanidza nendege yepasi yechinangwa chemudziyo
TCK/SCLK	Test Clock Input	Output	Inoshandiswa kuvharisa IEEE1149.1 state muchina
INIT	Tanga	Input	Inoratidza mudziyo wagadzirira kuti gadziriro itange. INITN inongowanikwa pane mamwe maturusi.
I2C: SCL*	I2C SCL	Output	Inopa iyo I2C chiratidzo SCL
I2C: SDA*	I2C SDA	Output	Inopa iyo I2C chiratidzo SDA.
5 V OUT*	5 V Kunze	Output	Inopa chiratidzo che5 V cheiyo iCEprogM1050 Programmer.

Cherechedza: Inowanikwa chete paHW-USBN-2B tambo.

Cherechedza: Inoda Diamond Programmer 3.1 kana gare gare.

Mufananidzo 3.2. Programming Cable In-System Programming Interface yePC (HW-USB-1A kana HW-USB-2A)*
Cherechedza: Lattice PAC-Designer® software haitsigire hurongwa ne USB tambo. Kuronga ispPAC zvishandiso netambo idzi, shandisa Diamond Programmer/ispVM System software.

Cherechedza: HW7265-DL3, HW7265-DL3A, HW-DL-3B, HW-DL-3C uye HW-DLN-3C zvigadzirwa zvakaenzana.

Mufananidzo 3.4. Programming Cable In-System Programming Interface yePC (pDS4102-DL2 kana pDS4102- DL2A)

Mufananidzo 3.5. Programming Cable In-System Programming Interface yePC (HW7265-DL2 kana HW7265-DL2A)*

Cherechedza: Nezvinangwa zvereferensi, iyo 2 x 10 yekubatanidza paHW7265-DL2 kana HW7265-DL2A yakaenzana neTyco 102387-1. Izvi zvichaenderana neyakajairwa 100-mil spacing 2 x 5 misoro, kana 2 x 5 kiyi, yakadzoreredzwa yechirume yekubatanidza se3M N2510-5002RB.

Kuronga Software

Diamond Programmer uye ispVM System yeClassic zvishandiso ndiyo inosarudzika programming management software yezvese Lattice zvishandiso uye tambo dzekurodha. Iyo yazvino vhezheni yeLattice Diamond Programmer kana ispVM System software inowanikwa kurodha kubva kuLattice web saiti pa www.latticesemi.com/programmer.

Target Board Design Kufunga

A 4.7 kΩ kudonhedza-pasi resistor inokurudzirwa pane TCK yekubatanidza yebhodhi inonangwa. Uku kudonhedza-pasi kunokurudzirwa kudzivirira kuvharika kusingafungire kweTAP controller inokonzereswa nekumhanya kwewachi micheto kana seVCC r.amps kumusoro. Uku kudonhedza-pasi kunokurudzirwa kune ese Lattice programmable mhuri.
Iyo I2C inosaina SCL uye SDA yakavhurika drain. A 2.2 kΩ kudhonza-kumusoro resistor kuVCC inodiwa pane yakanangwa bhodhi. Chete VCC kukosha kwe3.3 V uye 2.5 V yeI2C inotsigirwa netambo dzeHW-USBN-2B.
Kumhuri dzeLattice mudziyo une simba rakaderera, zvinokurudzirwa kuwedzera 500 Ω resistor pakati peVCCJ neGND panguva yekupindirana kwechirongwa kana USB programming tambo yakabatana kune yakaderera simba bhodhi dhizaini. A FAQ iripo inokurukura izvi zvakadzama pa:
http://www.latticesemi.com/en/Support/AnswerDatabase/2/2/0/2205
Iye JTAG programming port speed ingangoda kudzorwa kana uchishandisa tambo dzeprogramme dzakabatana nevatengi PCB. Izvi zvinonyanya kukosha kana paine PCB refu routing kana paine akawanda daisy-cheni michina. Iyo Lattice programming software inogona kugadzirisa nguva yeTCK inoshandiswa kuJTAG programming port kubva kune tambo. Iyi yakaderera-chaiyo yekumisikidza chiteshi cheTCK inoenderana nezvinhu zvakawanda, kusanganisira kumhanya kwePC uye rudzi rwetambo inoshandiswa (parallel port, USB kana USB2). Iyi software inoita sarudzo yekudzikisa TCK yedebug kana nharaunda dzine ruzha. A FAQ iripo inokurukura izvi zvakadzama pa: http://www.latticesemi.com/en/Support/AnswerDatabase/9/7/974.aspx
Iyo USB yekurodha tambo inogona kushandiswa kuronga Power Manager kana ispClock zvigadzirwa neLattice programming software. Paunenge uchishandisa USB tambo ine Power Manager I zvishandiso, (POWR604, POWR1208, POWR1208P1), unofanira kunonoka kuita TCK nechikamu che 2. FAQ iripo inokurukura izvi zvakadzama pa:
http://www.latticesemi.com/en/Support/AnswerDatabase/3/0/306.aspx

Programming Flywire uye Connection Reference

Tarisa Tafura 6.1 kuti uone, paLattice mudziyo, maitiro ekubatanidza akasiyana Lattice programming cable flywires. JTAG, SPI uye I2C kumisikidza yakaonekwa zvisina kujeka. Legacy cables uye hardware zvinosanganisirwa kuti zvitaurwe. Mukuwedzera, zvakasiyana-siyana zvemusoro zvigadziriso zvakarongwa.
Tafura 6.1. Pini uye Cable Reference

HW-USBN-2B Flywire color	TDI/SI	TDO/SO	TMS	TCK/SCLK	ISPEN/PROG	ZVAITA	TRST(OUTPUT)	VCC	GND	I2C
	Orenji	Bhurawuni	Pepuru	Chena	Yero	Bhuruu	Girinhi	Tsvuku	Nhema	Yero
HW-USBN-2A Flywire color	TDI	TDO	TMS	TCK	ispEN/PROG	INIT	TRST(OUTPUT)/DONE(INPUT)	VCC	GND
	Orenji	Bhurawuni	Pepuru	Chena	Yero	Bhuruu	Girinhi	Tsvuku	Nhema
HW-DLN-3C Flywire color	TDI	TDO	TMS	TCK	ispEN/PROG	na	TRST(OUTPUT)	VCC	GND
	Orenji	Bhurawuni	Pepuru	Chena	Yero		Girinhi	Tsvuku	Nhema
Programming cable pin type Target Board Recommendation	Output	Input	Output	Output	Output	Input	Input/Output	Input	Input	Ou
	—	—	4.7 kΩ Dhonza-Kumusoro	4.7 kΩ Dhonza-Pasi	(Cherechedzo 1)	—	—	(Cherechedzo 2)	—	(Aihwa (Aihwa
	Batanidza iyo programming tambo waya (pamusoro) kune inoenderana mudziyo kana header pini (belo

JTAG Port Devices

ECP5™	TDI	TDO	TMS	TCK	Sarudzo yekubatanidza kune mudziyo ispEN, PROGRAMN, INITN, DONE uye/kana TRST masiginecha (Tsanangura muCustom I/O marongero mune ispVM System kana Diamond Programmer software. Haasi ese maturusi ane mapini aya aripo)	Zvinodiwa	Zvinodiwa
LatticeECP3™/LatticeECP2M™ LatticeECP2™/LatticeECP™/LatticeEC™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
LatticeXP2™/LatticeXP™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
LatticeSC™/LatticeSCM™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
MachXO2™/MachXO3™/MachXO3D™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
MachXO™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
ORCA®/FPSC	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
ispXPGA®/ispXPLD™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
ispMACH® 4000/ispMACH/ispLSI® 5000	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
MACH®4A	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
ispGDX2™	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
ispPAC®/ispClock™ (Cherechedzo 4)	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa
Platform Manager™/Simba Maneja/Simba Maneja II/Platform Maneja II (Cherechedzo 4)	TDI	TDO	TMS	TCK		Zvinodiwa	Zvinodiwa

Tafura 6.1. Pini uye Cable Reference

HW-USBN-2B Flywire color	TDI/SI	TDO/SO	TMS	TCK/SCLK	ISPEN/PROG	ZVAITA	TRST(OUTPUT)	VCC	GND	I2C
	Orenji	Bhurawuni	Pepuru	Chena	Yero	Bhuruu	Girinhi	Tsvuku	Nhema	Yello
HW-USBN-2A Flywire color	TDI	TDO	TMS	TCK	ispEN/PROG	INIT	TRST(OUTPUT)/DONE(INPUT)	VCC	GND
	Orenji	Bhurawuni	Pepuru	Chena	Yero	Bhuruu	Girinhi	Tsvuku	Nhema
HW-DLN-3C Flywire color	TDI	TDO	TMS	TCK	ispEN/PROG	na	TRST(OUTPUT)	VCC	GND
	Orenji	Bhurawuni	Pepuru	Chena	Yero		Girinhi	Tsvuku	Nhema
Programming cable pin type Target Board Recommendation	Output	Input	Output	Output	Output	Input	Input/Output	Input	Input	O
	—	—	4.7 kΩ Dhonza-Kumusoro	4.7 kΩ Dhonza-Pasi	(Cherechedzo 1)	—	—	(Cherechedzo 2)	—	(N (N
	Batanidza iyo programming tambo waya (pamusoro) kune inoenderana mudziyo kana header pini (pazasi

Muranda SPI Port Devices

ECP5	MOSI	MISO	—	CCLK	SN	Optional kubatanidza kune mudziyo PROGRAMN, INITN uye/kana DONE masaini		Zvinodiwa	Zvinodiwa
LatticeECP3	MOSI	MISO	—	CCLK	SN			Zvinodiwa	Zvinodiwa
MachXO2/MachXO3/MachXO3D	SI	SO	—	CCLK	SN			Zvinodiwa	Zvinodiwa
CrossLink™ LIF-MD6000	MOSI	MISO	—	SPI_SCK	SPI_SS	Opt. CDONE	CRESET_B	Zvinodiwa	Zvinodiwa
iCE40™/iCE40LM/iCE40 Ultra™/ iCE40 UltraLite™	SPI_SI	SPI_SO	—	SPI_SCK	SPI_SS_B	Opt. CDONE	CRESET_B	Zvinodiwa	Zvinodiwa

I2C Port Zvishandiso

MachXO2/MachXO3/MachXO3D	—	—	—	—	Optional kubatanidza kune mudziyo PROGRAMN, INITN uye/kana DONE masaini			Zvinodiwa	Zvinodiwa
Platform Manager II	—	—	—	—				Zvinodiwa	Zvinodiwa	SCL_M
L-ASC10	—	—	—	—	—	—	—	Zvinodiwa	Zvinodiwa
CrossLink LIF-MD6000	—	—	—	—	—	Opt. CDONE	CRESET_B	Zvinodiwa	Zvinodiwa

Headers

1 x 10 conn (tambo dzakasiyana)	3	2	6	8	4	9 kana 10	5 kana 9	1	7
1 x 8 conn (ona Mufananidzo 3.4)	3	2	6	8	4	—	5	1	7
2 x 5 conn (ona Mufananidzo 3.5)	5	7	3	1	10	—	9	6	2, 4, kana 8

Programmers

Muenzaniso 300	5	7	3	1	10	—	9	6	2, 4, kana 8
iCEprog™ iCEprogM1050	8	5	—	7	9	3	1	6	10

Notes: 

• Kune ekare Lattice ISP zvishandiso, 0.01 μF decoupling capacitor inodiwa pane ispEN/INOITA yebhodhi rinonangwa.
• Kune HW-USBN-2A/2B, bhodhi rinotarisirwa rinopa simba - Typical ICC = 10 mA. Pamidziyo ine pini yeVCCJ, VCCJ inofanira kunge yakabatana midziyo, batanidza bhangi rakakodzera VCCIO kuVCC yetambo. A 0.1 μF decoupling capacitor inodiwa paVCCJ kana VCCIO padyo nemudziyo. pepa rekuona kana mudziyo une pini yeVCCJ kana kuti VCCIO bhanga rinotonga chinonangwa chekugadzira chirongwa (ichi chingave chisina kufanana nechakanangwa 3. Vhura masaini emvura. Targe board inofanira kuva ~ 2.2 kΩ pull-up resistor yakabatana kune imwecheteyo. ndege iyo VCC yakabatana nayo HW-USBN-2B tambo kuVCC.
• Paunenge uchishandisa PAC-Designer® software kuronga ispPAC kana ispClock zvishandiso, usabatanidza TRST/DONE.
• Kana ukashandisa tambo yakakura kupfuura HW-USBN-2B, batanidza +5 V yekunze inopihwa pakati iCEprogM1050 pin 4 (VCC) nepini 2 (GND).
• Kune HW-USBN-2B, chete VCC kukosha kwe3.3 V thru 2.5 V inotsigirwa I2C.

Kubatanidza iyo Programming Cable

Bhodhi rinonangwa rinofanira kunge risina simba paunenge uchibatanidza, kubvisa, kana kubatanidza tambo yepurogiramu. Gara uchibatanidza tambo yeGND yepini (waya nhema) usati wabatanidza chero imwe JTAG pini. Kutadza kutevedzera maitiro aya kunogona kukonzera kukuvadzwa kune chinongedzo chinorongwa mudziyo.

Programming Cable TRST Pin

Kubatanidza bhodhi TRST pini kune cable TRST pini hazvikurudzirwe. Pane kudaro, batanidza bhodhi TRST pini kuVcc. Kana bhodhi TRST pin yakabatana netambo TRST pini, raira ispVM/Diamond Programmer kutyaira iyo TRST pini kumusoro.

Kugadzirisa ispVM/Diamond Programmer kutyaira TRST pini yakakwirira:

• Sarudza iyo Options menyu chinhu.
• Sarudza Cable uye I/O Port Setup.
• Sarudza TRST/Reset Pin-Yakabatanidzwa checkbox.
• Sarudza bhatani reSet High radio.

Kana iyo sarudzo isina kusarudzwa, pini yeTRST inotungamirwa yakaderera ne ispVM/Diamond Programmer. Nekuda kweizvozvo, iyo BSCAN cheni haishande nekuti cheni yakavharirwa mune RESET mamiriro.

Programming Cable ispEN Pin

Mapini anotevera anofanirwa kuiswa pasi:

• BSCAN pini ye2000VE zvishandiso
• ENABLE pin of MACH4A3/5-128/64, MACH4A3/5-64/64 and MACH4A3/5-256/128 devices.

Nekudaro, iwe une sarudzo yekuve neBSCAN uye ENABLE mapini anofambiswa neispEN pini kubva patambo. Muchiitiko ichi, ispVM/Diamond Programmer inofanira kugadzirwa kuti ityaire ispEN pini yakaderera sezvinotevera:
Kugadzirisa ispVM/Diamond Programmer kutyaira ispEN pini yakaderera:

1. Sarudza iyo Options menyu chinhu.
2. Sarudza Cable uye I/O Port Setup.
3. Sarudza ispEN/BSCAN Pin Yakabatanidzwa checkbox.
4. Sarudza bhatani reSet Low radio.

Imwe neimwe programming cable ngarava ine maviri madiki majoini anokubatsira iwe kuchengeta nhunzi dzakarongeka. Iyo inotevera mugadziri uye chikamu nhamba ndiyo imwe inogoneka sosi yeakaenzana majoini:

• 1 x 8 Chibatanidza (chemufample, Samtec SSQ-108-02-TS)
• 2 x 5 Chibatanidza (chemufample, Samtec SSQ-105-02-TD)

Iyo programming cable flywire kana misoro inoitirwa kubatanidza kune yakajairwa 100-mil spacing misoro (mapini akaparadzana 0.100 inch apart). Lattice inokurudzira musoro une hurefu hwe 0.243 inches kana 6.17 mm. Kunyange zvakadaro, misoro yehumwe hurefu inogona kushanda zvakaenzana.

Kuraira Ruzivo

Tafura 10.1. Programming Cable Feature Summary

Feature	HW-USBN-2B	HW-USBN-2A	HW-USB-2A	HW-USB-1A	HW-DLN-3C	HW7265-DL3, HW7265-DL3A, HW-DL-3B, HW-DL-3C	HW7265-DL2	HW7265-DL2A	PDS4102-DL2	PDS4102-DL2A
USB	X	X	X	X	—	—	—	—	—	—
PC-Parallel	—	—	—	—	X	X	X	X	X	X
1.2 V Tsigiro	X	X	X	—	—	—	—	—	—	—
1.8 V Tsigiro	X	X	X	X	X	X	—	X	—	X
2.5-3.3 V Support	X	X	X	X	X	X	X	X	X	X
5.0 V Tsigiro	—	X	X	X	X	X	X	X	X	X
2 x 5 Chinongedzo	—	X	X	X	X	X	X	X	—	—
1 x 8 Chinongedzo		X	X	X	X	X	—	—	X	X
Flywire	X	X	X	X	X	X	—	—	—	—
Lead-isina Kuvaka	X	X	—	—	X	—	—	—	—	—
Inowanikwa kune odha	X	—	—	—	X	—	—	—	—	—

Tafura 10.2. Kuhodha Ruzivo

Tsanangudzo	Kuodha Chikamu Nhamba	China RoHS Zvakatipoteredza- Hushamwari Kushandisa Period (EFUP)
Programming tambo (USB). Iine 6′ USB tambo, flywire connectors, 8-position (1 x 8) adapta uye gumi-nzvimbo (10 x 2) adapta, lead-isina, RoHS inoenderana kuvaka.	HW-USBN-2B
Programming tambo (PC chete). Iine parallel port adapter, 6′ cable, flywire connectors, 8-position (1 x 8) adapta uye gumi- chinzvimbo (2 x 5) adapta, lead-isina, RoHS inoenderana kuvaka.	HW-DLN-3C

Cherechedza: Mamwe tambo anotsanangurwa mugwaro rino nechinangwa chenhaka chete, tambo idzi hadzichagadzirwa. Tambo dziripo pari zvino kuodha zvinhu zvakaenzana zvakaenzana.

Appendix A. Troubleshooting the USB Driver Installation

Izvo zvakakosha kuti iwe uise madhiraivha usati wabatanidza PC yako kune USB tambo. Kana tambo yakabatana isati yaisa madhiraivha, Windows inoedza kuisa madhiraivha ayo anogona kusashanda.
Kana waedza kubatanidza PC ku USB tambo usina kutanga waisa madhiraivha akakodzera, kana kunetseka kutaurirana neLattice USB tambo mushure mekuisa madhiraivha, tevera matanho ari pasi apa:

1. Batanidza iyo Lattice USB tambo. Sarudza Tanga> Zvirongwa> Control Panel> System.
2. MuSystem Properties dialog box, tinya iyo Hardware tab uye Device Manager bhatani. Pasi pe Universal Serial Bhazi controllers, iwe unofanirwa kuona Lattice USB ISP Chirongwa. Kana iwe usingaone izvi, tsvaga iyo Isingazivikanwe Chishandiso chine yero mureza. Dzvanya kaviri pane iyo Unknown Device icon.
3. Muiyo Isingazivikanwe mudziyo Properties dialog box, tinya Reinstall Driver.
4. Sarudza Bhurawuza komputa yangu yedhiraivha software.
   Bhurawuza kune isptools\ispvmsystem dhairekitori yeLattice EzUSB mutyairi.
   Bhurawuza kune isptools\ispvmsystem\Drivers\FTDIUSBDriver dhairekitori yeFTDI FTUSB mutyairi.
5. Nekumisikidzwa kweDiamondi, tarisa kune lscc/diamond/data/vmdata/madhiraivha. Click Next.
6. Sarudza Isa iyi Driver software zvakadaro. Iyo system inovandudza mutyairi.
7. Dzvanya Close uye pedzisa kuisa USB mutyairi.
8. Pazasi Kudzora Panel> System> Chishandiso Maneja> Universal Serial Bus Controllers inofanira kusanganisira zvinotevera: YeLattice EzUSB Driver: Lattice USB ISP Programmer mudziyo wakaiswa.

YeFTDI FTUSB Driver: USB Serial Converter A uye Converter B zvishandiso zvakaiswa

Kana urikusangana nematambudziko kana uchida rumwe ruzivo, bata Lattice Technical Support.

Technical Support

Kuti uwane rubatsiro, tumira kesi yetsigiro yehunyanzvi pa www.latticesemi.com/techsupport.

Revision History

Kudzokorora 26.4, Chivabvu 2020

Chikamu	Chinja Pfupiso
Programming Cables	Yakagadziridzwa Lattice websaiti link kune www.latticesemi.com/programmer.
Kuronga Software

Kudzokorora 26.3, Gumiguru 2019

Chikamu	Chinja Pfupiso
Target Board Design Kufunga; Programming Flywire uye Connection Reference	Yakajekeswa VCC maitiro ayo I2C interface inotsigira. Akawedzera manotsi kuTafura 6.1.

Kudzokorora 26.2, Chivabvu 2019

Chikamu	Chinja Pfupiso
—	Yakawedzerwa Disclaimer chikamu.
Programming Flywire uye Connection Reference	Yakagadziridzwa Tafura 6.1. Pini uye Cable Reference. Yakawedzera MachXO3D Yakawedzerwa CRESET_B kuCrosslink I2C. Zvinhu zvakagadziridzwa pasi peI2C Port Devices · Yakawedzera Platform Manager II. · Yakachinja odha yeispPAC. Zvinhu zvakagadziridzwa pasi peI2C Port Devices. · Yakachinja Maneja Wesimba II kuita Platform Maneja II uye yakagadziridzwa I2C: SDA kukosha. Yakashandurwa ASC kuita L-ASC10 Yakagadziridzwa chinyorwa chepasi 4 kuti ibatanidze ispClock zvishandiso. Mavara akagadziridzwa.
Revision History	Yakagadziridzwa fomati.
Back cover	Updated template.
—	Shanduko diki dzekupepeta

Kudzokorora 26.1, Chivabvu 2018

Chikamu	Chinja Pfupiso
Zvose	Yakagadziriswa mapindiro muSlave SPI Port Devices chikamu cheTafura 6.1.

Kudzokorora 26.0, Kubvumbi 2018

Chikamu	Chinja Pfupiso
Zvose	Yakachinja gwaro nhamba kubva kuUG48 kuenda kuFPGA-UG-02024. Yakagadziridzwa gwaro template.
Programming Cables	Yakabvisa ruzivo rwakashata uye yakachinja chinongedzo ku www/latticesemi.com/software.
Programming Cable Pin Definitions	Yakagadziridzwa Programming Cable Pini mazita muTafura 3.1. Programming Cable Pin Definitions.
Programming Flywire uye Connection Reference	Yakatsiviwa Tafura 2. Flywire Conversion Reference uye Tafura 3 Yakakurudzirwa Pini Kubatanidza neTafura imwe chete 6.1 Pini uye Cable Reference.
Kuraira Ruzivo	Yakafambiswa Tafura 10.1. Programming Cable Feature Summary pasi peKuodha Ruzivo.

Kudzokorora 25.0, Mbudzi 2016

Chikamu	Chinja Pfupiso
Programming Flywire uye Connection Reference	Yakadzokororwa Tafura 3, Yakakurudzirwa Pin Connections. Yakawedzera CrossLink mudziyo.

Kudzokorora 24.9, Gumiguru 2015

Chikamu	Chinja Pfupiso
Programming Flywire uye Connection Reference	Yakadzokororwa Tafura 3, Yakakurudzirwa Pin Connections. Yakawedzerwa CRESET-B column. Yakawedzera iCE40 UltraLite mudziyo.
Rubatsiro Rutsigiro rwehunyanzvi	Yakagadziridzwa ruzivo rweTechnical Support Rubatsiro.

Kudzokorora 24.8, Kurume 2015

Chikamu	Chinja Pfupiso
Programming Cable Pin Definitions	Tsanangudzo yakadzokororwa yeINIT muTable 1, Programming Cable Pin Definitions.

Kudzokorora 24.7, Ndira 2015

Chikamu	Chinja Pfupiso
Programming Cable Pin Definitions	MuTable 1, Programming Cable Pin Definitions, ispEN/Enable/PROG yakashandurwa kuita ispEN/Enable/PROG/SN uye tsananguro yayo yakadzokororwa. Yakagadziridzwa Mufananidzo 2, Programming Cable In-System Programming Interface yePC (HW-USBN-2B).
Programming Cable ispEN Pin	MuTable 4, Programming Cable Feature Summary, HW-USBN-2B yakamakwa seinowanikwa kuodha.
Kuraira Ruzivo	HW-USBN-2A yakashandurwa kuita HW- USBN-2B.

Kudzokorora 24.6, Chikunguru 2014

Chikamu	Chinja Pfupiso
Zvose	Yakachinjwa zita regwaro kubva kuispDOWNLOAD Cables kuenda kuProgramming Cables User's Guide.
Programming Cable Pin Definitions	Yakagadziridzwa Tafura 3, Yakakurudzirwa Pini Mabatanidza. Yakawedzera ECP5, iCE40LM, iCE40 Ultra, uye MachXO3 mudziyo mhuri.
Target Board Design Kufunga	Updated chikamu. Yakagadziridzwa FAQ link pane ispVM chishandiso chekudzora cheTCK basa kutenderera uye/kana frequency.
Rubatsiro Rutsigiro rwehunyanzvi	Yakagadziridzwa ruzivo rweTechnical Support Rubatsiro.

Kudzokorora 24.5, Gumiguru 2012

Chikamu	Chinja Pfupiso
Programming Flywire uye Connection Reference	Yakawedzera iCE40 yekumisikidza mapini mazita kune iyo Flywire Conversion Reference tafura.
Programming Flywire uye Connection Reference	Yakawedzera iCE40 ruzivo kune Yakakurudzirwa Cable Connections tafura.

Kudzokorora 24.4, Kukadzi 2012

Chikamu	Chinja Pfupiso
Zvose	Gwaro rakagadziridzwa rine logo itsva yekambani.

Kudzokorora 24.3, Mbudzi 2011

Chikamu	Chinja Pfupiso
Zvose	Gwaro raendeswa kufomati yegwaro remushandisi.
Features	Yakawedzerwa Mufananidzo USB Cable - HW-USBN-2A.
Programming Flywire uye Connection Reference	Yakagadziridzwa Yakakurudzirwa Cable Connections tafura yeMachXO2 zvishandiso.
Target Board Design Kufunga	Updated chikamu.
Appendikisi A	Chikamu chakawedzerwa.

Kudzokorora 24.2, Gumiguru 2009

Chikamu	Chinja Pfupiso
Zvose	Yakawedzera ruzivo rwakabatana nechimiro chechimiro cheiyo flywire connectors.

Kudzokorora 24.1, Chikunguru 2009

Chikamu	Chinja Pfupiso
Zvose	Yakawedzerwa Target Board Dhizaini Yekutarisisa chinyorwa chikamu.
Programming Flywire uye Connection Reference	Yakawedzerwa musoro wechikamu.

Previous Revisions

Chikamu	Chinja Pfupiso
—	Previous Lattice inoburitswa.

www.latticesemi.com

Zvinyorwa / Zvishandiso

LATTICE FPGA-UG-02042-26.4 Programming Cables [pdf] Bhuku reMushandisi FPGA-UG-02042-26.4 Programming Cables, FPGA-UG-02042-26.4, Programming Cables, Cables

References

• User Manual