INTERMOTIVE ILISC515-A shine Tsarin Tubar Microprocessor

Bayanin samfur

Ƙayyadaddun bayanai:

• Sunan samfur: ILISC515-Madaidaicin Maɓalli na Shift (Kofar ɗagawa ta Manual)
• Mota mai jituwa: 2015 - 2019 Ford Transit
• Zaɓin Ƙarawa: ILISC515-AD tare da Door Ajar panel
• Mai ƙira: InterMotive, Inc. girma
• Adireshi: 12840 Earhart Ave Auburn, CA 95602
• Tuntuɓar: Waya: 530-823-1048 Fax: 530-823-1516

Umarnin Amfani da samfur

Shigar da kayan aikin Data Link:

1. Nemo Haɗin Haɗin Bayanan Bayanan OBDII na abin hawa a ƙarƙashin ɓangaren dash na hagu na ƙasa.
2. Cire mai haɗin White OBDII daga dash panel kuma toshe a cikin mahaɗin ja daga ILISC515-A Data Link Harness cikin mahaɗin OBDII na abin hawa.
3. Dutsen farar hanyar wucewa ta hanyar haɗin kai daga ILISC515-A Data Link Harness a madadin mai haɗin OBDII na abin hawa.
4. Aminta da kayan aikin haɗin bayanai na ILISC515-A don hana ratayewa ƙasa da ƙaramin dash panel.
5. Haɗa ƙarshen kyauta na kayan haɗin Data zuwa mahaɗin mahaɗin 4-pin akan tsarin ILISC515-A.

Haɗa Shigar Ƙofar Dago:

• Idan abin hawa ba shi da maɓallai na baya ko na gefe, shigar da haɗa maɓallin kofa zuwa fil 8 (waya launin toka) na mai haɗin fil 8.
• Don motocin da ke da musanya kofa na OEM, ƙirar zata iya karanta matsayin kofa ta hanyar sadarwar abin hawa. Bi takamaiman umarni dangane da daidaitawar abin hawan ku.

Sarrafa Abubuwan Shiga/Sakamako - Mai haɗin-pin 8:
Ricon Braun yana ɗagawa: Haɗa zuwa fil #6 na mahaɗin 9-pin. Don shigar da Kulle Shift na zaɓi, haɗa wayar Yellow zuwa babban fitarwa na gaskiya kuma saka fil a cikin fil #1 a mai haɗin fil 8.

FAQ:

• Tambaya: Menene zan yi idan abin hawa na ba shi da maɓallan kofa na OEM?
  A: Idan abin hawan ku ba shi da maɓallan kofa na OEM, kuna buƙatar shigar da shigarwar sadarwa ta hanyar ɗagawa sama da ƙofa don sarrafa tsarin yadda ya kamata.
• Tambaya: Ta yaya zan kunna kulle motsi ta amfani da ILISC515-A Shift Interlock?
  A: Haɗa wayar rawaya zuwa tushen samar da babban fitarwa na Gaskiya kuma saka shi cikin fil #1 a mahaɗin 8-pin don kunna ayyukan kulle motsi.

Gabatarwa

ILISC515-A tsari ne na microprocessor don sarrafa aikin ɗaga keken hannu. Tsarin tsoho na iya aiki tare da kunnawa ko kashe abin hawa. Za a kunna aikin ɗagawa lokacin da takamaiman yanayin amincin abin hawa ya cika kuma zai kulle watsawa a cikin wurin shakatawa lokacin da hawan keken guragu ke aiki. Plug na zaɓi da kayan aikin Play suna samuwa don yawancin aikace-aikacen, yin shigarwa cikin sauri da sauƙi. Ana samun aikin "KASHE KAWAI" tare da saitin umarni don canza yanayin aiki.

ILISC515 Ƙara-On Zaɓin
ILISC515-AD tare da Door Ajar panel: Kula da ƙarin kofofin ban da ƙofar ɗagawa.

MUHIMMI- KARANTA KAFIN SHIGA
Alhakin mai sakawa ne don hanya da kiyaye duk kayan aikin wayoyi inda ba za a iya lalacewa ta hanyar abubuwa masu kaifi, sassa masu motsi na inji, da manyan hanyoyin zafi ba. Rashin yin haka zai iya haifar da lalacewa ga tsarin ko abin hawa da haifar da yiwuwar tsaro ga ma'aikaci da fasinjoji. Guji sanya module inda zai iya cin karo da filayen maganadisu masu ƙarfi daga babban cabling na yanzu da aka haɗa da injina, solenoids, da sauransu. Guji ƙarfin mitar rediyo daga eriya ko inverters kusa da tsarin. Guji babban voltage spikes a cikin abin hawa ta hanyar amfani da diode-cl koyausheamped relays lokacin shigar upfitter da'irori.

Umarnin Shigarwa

Cire haɗin baturin abin hawa kafin a ci gaba da shigarwa. 

Bayani na ILSC515-A
Cire ƙananan dash panel a ƙarƙashin yankin ginshiƙan tuƙi kuma nemo wurin da ya dace don hawan module ɗin don LEDs Diagnostic na module ɗin su kasance. viewed tare da ƙananan dash panel cire. Nemo samfurin a wani yanki mai nisa daga kowane tushen zafi mai zafi (zafin inji, bututun dumama, da sauransu). Kar a hau tsarin har sai an lalata duk kayan aikin waya da tsaro. Mataki na ƙarshe na shigarwa shine don hawa tsarin.

Data L tawada Harness Installation 

1. Nemo abin hawan OBDII Data Link Connector, wanda aka ɗora a ƙasan ɓangaren dash na hagu na ƙasa.
2. Cire mai haɗin White OBDII daga dash panel ta matse bangarorin biyu na mai haɗin. Toshe mai haɗin ja daga ILISC515-A Data Link Harness cikin mahaɗin OBDII na abin hawa. Tabbatar cewa haɗin yana zaune cikakke kuma amintacce tare da tayen waya da aka kawo.
3. Dutsen farar hanyar wucewa ta hanyar haɗin kai daga ILISC515-A Data Link Harness a tsohon wurin haɗin OBDII na abin hawa.
4. Tsare kayan aikin ILISC515-A Data Link don kada ya rataya a ƙasan ƙananan dash panel.
5. Toshe ƙarshen kyauta na kayan aikin Data Link a cikin mahaɗin mahaɗin 4-pin akan tsarin ILISC515-A.

LED nuni Panel hawa

LED Nuni Panel hawa - Black 4-pin connector
Nemo wuri mai dacewa akan dashboard, ciki view na direba don hawa da LED nuni Panel. Tabbatar cewa akwai buɗaɗɗen sarari a bayan dash inda aka ɗora kwamitin. Harness ɗin yana da 40 inci a tsayi, wanda shine matsakaicin nisa da nuni zai iya kasancewa daga tsarin.

1. Hana rami 5/8 inci a cikin dash inda tsakiyar nunin zai kasance.
2. Haɗa mai haɗin Black 4-pin na kayan aikin nuni na LED zuwa tsarin.
3. Gudu sauran ƙarshen kayan doki a ƙarƙashin dash kuma fita ta cikin ramin 5/8 ".
4. Haɗa ƙarshen zuwa Panel Nuni LED.
5. Tabbatar cewa panel ɗin ya daidaita kuma yana amintacce ta amfani da sukurori da aka kawo.

Haɗa shigar da Ƙofar ɗagawa
Idan kuna aiki akan abin hawa wanda ba shi da madaidaicin ƙofa na baya ko na gefe (cutaway chassis), dole ne a shigar da maɓallin kofa (a kan ƙofar da ta dace (ɗagawa) kuma a haɗa ta da fil 8 na module (waya launin toka) na 8 -pin connector (duba CAD zane mai dacewa). NOTE: Dole ne wannan shigarwar ta samar da ƙimar matakin ƙasa lokacin da ƙofar ke buɗe (Low-Gaskiya). Don irin wannan abin hawa, wannan shine kawai abin da ake buƙata don gano kofa.

A kan abin hawa wanda aka sanye da ƙofar OEM tare da masu sauyawa, ƙirar zata iya karanta matsayin kofa akan hanyar sadarwar abin hawa. Saitin tsohuwar tsarin yana karanta matsayin kofa akan hanyar sadarwar abin hawa kuma yana aiki a yanayin "Maɓalli A Kan Kawai".1 Saboda haka, shigar da shigar da ƙofar ɗagawa mai hankali ya zama dole kawai don sarrafa tsarin a yanayin "Key Off Only", "Key On On Only". ” yanayin, ko kuma idan motar ba ta da maɓallan kofa na OEM. Sashe na gaba yana ɗauka cewa motar ta riga an shigar da maɓallan ƙofa kuma yayi bayanin yadda ake haɗa haɗin kai.

Haɗin Haɗin Side Door na OEM

Idan ana son aiki na “KEYSHE”, dole ne a sanya shigarwar Ƙofar Lift mai hankali zuwa tsarin. Ana cim ma wannan ta hanyar haɗawa da kayan aikin sauya abin hawa sama da bayan kujerar direba. Amintacce haɗa wayar Grey na kayan doki 8-pin zuwa wayar Yellow OEM waya. Idan amfani da Posi-Tap, bi umarnin da ke ƙasa.

Wayar kofa ta zamewa (rawaya) tana cikin wannan kayan doki. Cire hular Grey a kan mahaɗin Posi-Tap kuma shigar da shi akan wayar da ta dace, sannan a murƙushe sauran mahaɗin a kan hular yana murza shi ƙasa amma ba sosai ba.

Cire dayan ƙarshen mai haɗin Posi-Tap, tsiri 1/4” insulation daga wayar Grey da ke fitowa daga fil 8 na module, sa'annan a saka ta cikin sassauƙan yanki don haka ƙarshen waya ya kasance tare da gefen yanki. Rike wayar don kada ta koma baya daga Posi-tap, sannan a murƙushe ta cikin babban jikin Posi-Tap. Rike babban jikin Posi-Tap, a hankali ja kan wayar da aka shigar kawai don tabbatar da an haɗa ta da kyau. Tsare haɗin gwiwa ta amfani da tef.

NOTE:
Akwai ƙarin jerin da dole ne a gudanar yayin shigarwa wanda ke gano ƙofar ɗagawa zuwa tsarin.

Sarrafa shigarwar / abubuwan fitarwa - mai haɗin fil 8

• ILISC515-A yana ba da abubuwan shiga ƙasa uku da 12V, 1 amp fitarwa.
• Koma zuwa zane ILISC515-A CAD azaman tunani lokacin karanta waɗannan umarnin. Ana iya buƙatar relay na sarrafawa don kunna wasu ɗagawa, saboda ɗagawar zana yanzu fiye da 1 amp. Shigar da (diode clamped) relay kamar yadda aka nuna akan zanen CAD.
• Tsawaita wayoyi masu zuwa yadda ya kamata, ta amfani da solder da zafi tubing ko tef.
• Ƙaƙƙarfan-yanke-waya (waya 4) yana ba da haɗin kai ga abin hawa kamar haka:
• Orange - haɗa wannan fitarwa zuwa na'ura mai ɗagawa ko ɗagawa. Koma zuwa musamman zanen ɗagawa lokacin yin wannan haɗin. Wannan fitarwa tana samar da 12V @ 1 amp lokacin da yake da aminci don sarrafa dagawar. Ana iya amfani da wannan don kunna Lift. Idan dagawa ya zana fiye da 1 amp, za a buƙaci shigar da relay mai sarrafawa.
• Grey – Wannan shigarwar dole ne ta “taba” zuwa waya mai sauya ƙofa mai ɗagawa kamar yadda umarnin ke nunawa (Duba a sama) ko haɗa kai tsaye zuwa maɓallin ƙofar da aka shigar. Ana iya amfani da wannan don gano kofofin bude/rufe.
• Yellow (Shift Kulle Shift na zaɓi) - Saka ƙarshen "ƙulle" na wariyar launin rawaya da aka haɗa cikin fil #1 na mahaɗin 8-pin kuma haɗa ɗayan ƙarshen zuwa kowane tushe wanda ke ba da babban matakin Gaskiya don ba da damar kulle motsi. Ana iya amfani da wannan don kunna kullewa lokacin rufe maɓalli.

Brown - Haɗa wannan waya kawai idan ana son aikin ɗagawa na "kashe".
Haɗa wannan zaɓin shigarwar ILISC-515 zuwa canjin birki na OEM Park (kamar yadda aka nuna) ana yin canjin lokacin da aka saita birki na Park. Shigar da diode mai daidaitawa (RL202-TPCT-ND ko makamancinsa) kamar yadda aka nuna a cikin zane na Blunt Cut CAD, don ware siginar ƙasan birki. Cire wasu abubuwan rufewa daga wayar OEM White/Violet, sayar da wayar Brown akan, da tef ko amfani da bututun zafi. Ana buƙatar wannan haɗin idan ana son aikin ɗagawa lokacin da wutan abin hawa ke KASHE.

• Fil #1- YELLOW (Shift Kulle Shigar) *Na zaɓi
• Pin #2 - N/C
• Fin #3 - ORANGE (Tsarin abin hawa (12V) Fitowa)
• Pin #4 - N/C
• Fil #5 — BROWN (Park birki (GND) Shigarwa) *Na zaɓi
• Pin #6 - N/C
• Fil #7 - ORANGE (An Jumpered zuwa Fin#3)
• Fil #8 - GRAY (Buɗe Buɗe Shigarwa)

Haɗa mai haɗa 8-pin zuwa module

Plug & Kunna Lift Harness

• Lemu - Wannan fitarwa yana ba da 12V @ 1 amp lokacin da yake da aminci don sarrafa dagawar. Yanke waya zuwa daidai tsayin fitilun da aka tanadar ta amfani da kayan aiki mai raɗaɗi kuma saka fil a cikin madaidaicin rami.
• Ricon dagawa: Haɗa zuwa fil #86 na relay mai sarrafawa. Toshe mahaɗin 4-pin cikin ɗagawa.
• Braun dagawa: Haɗa zuwa fil #6 na mahaɗin 9-pin.
• Shigar Kulle Shift na zaɓi: Haɗa wayar rawaya zuwa kowane tushe wanda ke ba da babban fitarwa na Gaskiya don kunna kulle motsi da saka fil cikin fil #1 a mai haɗin-pin 8.
• Grey – Wannan shigarwar dole ne “taɓa” zuwa waya mai sauya ƙofa mai ɗagawa kamar yadda umarnin ya nuna (Duba bayanin shigarwa).
  • Fil #1 - BUDE (Shigar Kulle Shift na zaɓi)
  • Pin #2 - N/C
  • Fin #3 - ORANGE (Tsarin abin hawa (12V) Fitowa)
  • Pin #4 - N/C
  • Fil #5 — BROWN (Park birki (GND) Shigarwa) *Na zaɓi
  • Pin #6 - N/C
  • Fil #7 - ORANGE (An Jumpered zuwa Fin#3)
  • Fil #8 - GRAY (Buɗe Buɗe Shigarwa)

Haɗa mai haɗa 8-pin zuwa module

Na Zabin Braun Plug & Kunna Relay Kit #900-00005
Motocin Braun na yanzu sun zana fiye da 1 amp kuma zai buƙaci kayan aikin toshe-da-wasa na Braun.

• Lemu - Wannan fitarwa yana ba da 12V lokacin da yake da aminci don sarrafa ɗagawa. Yanke waya zuwa tsayin daidai haɗe da ɗaya daga cikin fil ɗin da aka bayar ta amfani da kayan aiki mai lalacewa kuma saka a fil #86 na relay ɗin da aka haɗa.
• Ja - Haɗa zuwa fil #6 na 9-pin Braun lift connector.
• Yellow (eyelet) - Haɗa zuwa + 12V na waje a ɗagawa.
• Baki (ido) - Haɗa zuwa ƙasa ta waje a ɗagawa.
• Shigar Kulle Shift na zaɓi: Haɗa wayar rawaya zuwa kowane tushe wanda ke ba da babban fitarwa na Gaskiya don kunna kulle motsi da saka fil cikin fil #1 a mai haɗin-pin 8.
• Grey – Wannan shigarwar dole ne “taɓa” zuwa waya mai sauya ƙofa mai ɗagawa kamar yadda umarnin ya nuna (Duba bayanin shigarwa).
  • Fil #1 - BUDE (Shigar Kulle Shift na zaɓi)
  • Pin #2 - N/C
  • Fin #3 - ORANGE (Tsarin abin hawa (12V) Fitowa)
  • Pin #4 - N/C
  • Fil #5 — BROWN (Park birki (GND) Shigarwa) *Na zaɓi
  • Pin #6 - N/C
  • Fil #7 - ORANGE (An Jumpered zuwa Fin#3)
  • Fil #8 - GRAY (Buɗe Buɗe Shigarwa)

Haɗa mai haɗa 8-pin zuwa module

Sake haɗa baturin abin hawa

Tabbatar cewa duk kayan aikin an haɗa su da kyau kuma an bi su. Tare da duk haɗin da aka yi, kunna KEY zuwa matsayin RUN - allon nuni ya kamata ya bayyana tare da duk LEDs masu haske na kusan daƙiƙa 2.

Ƙofar Ƙofar Ƙofa

Saitin tsoho na ƙirar yana da ƙofar ɗagawa azaman ƙofar baya da matsayin kofa akan hanyar sadarwar abin hawa. Idan abin hawa yana da gefen OEM da kofofin baya tare da ginannen maɓalli, ƙirar tana buƙatar sanin wanne daga cikin kofofin biyu masu yiwuwa (gefe ko na baya) aka ayyana su zama ƙofar ɗagawa. Dole ne a yi hanya mai zuwa don cimma wannan:

1. Tabbatar Gefe da Ƙofofin Baya gaba ɗaya an rufe su
2. Motar tana cikin PARK tare da Maɓalli a wurin RUN da injin KASHE
3. Ana amfani da birki na Park
4. Sanya tsarin a cikin yanayin bincike ta hanyar haɗawa da pads ɗin gwajin TP6 a hankali - LEDs module ɗin za su gungurawa, sannan LED1 za ta “fitar da” sigar firmware, kuma a ƙarshe LEDs 1 - 3 (aƙalla) za su zo a tsaye.
5. Jira LED1 don kammala “kyaftawa” sigar firmware kuma duk LEDs sun tsaya tsayin daka.
6. Juya fedal ɗin Sabis (sau 4 a cikin daƙiƙa 5) har sai kun ga LEDs 1 – 4 suna kiftawa tare.
7. Bude kofar dagawa; LEDs ɗin naúrar za su daina kiftawa kuma su kasance KASHE.
8. Tabbatar cewa an san kofa ta ɗaga ta buɗewa da rufe ta yayin kallon LED ɗin "Ƙofa Buɗe" akan allon nuni. Idan babu nuni ko kuma idan ma'anar ta yi kama da abin da ya kamata, dole ne a maimaita jerin abubuwan da suka gabata.

NOTE:
Idan an yi hanyar haɗin kai don ƙofar ɗagawa, ƙirar za ta yi amfani da shigarwar mai hankali (pin 8) musamman daga wannan wurin don tantance matsayin ƙofar ɗagawa.

Motocin Cutaway Kawai (Sigar Firmware 4.08 ko sama)

1. Tabbatar cewa Gefe da Ƙofofin Baya sun rufe gaba ɗaya.
2. Motar tana cikin PARK tare da Maɓalli a wurin RUN, ko dai direban ko ƙofar fasinja dole ne a buɗe, injin ɗin yana KASHE, kuma wayar Grey akan haɗin haɗin 8-pin ba ta ƙasa ba, kuma/ko ƙofar ɗagawa ta rufe. .
3. Aiwatar da birki na Park.
4. Sanya tsarin a cikin yanayin bincike ta latsa maɓallin "Test" na Red a kan module - LEDs modules za su gungurawa, sannan LED1 zai "kyauta" sigar firmware, kuma LEDs 1 - 3 (aƙalla) za su zo a tsaye.
5. Latsa kuma ci gaba da riƙe Birkin Sabis yayin yin matakai na 5 zuwa 6.
6. Danna maɓallin "Gwaji" na Red a karo na biyu akan tsarin - Matsayin LED, LED1, da LED2 za su lumshe kunne da Kashe a hankali.
7. Tsallaka ƙasa zuwa Wayar Grey akan mahaɗin 8-pin ko kuma a sa mutum na biyu ya buɗe Ƙofar ɗagawa wanda wayar Grey ke haɗe da ita.
8. LEDs 1 - 4 za su yi kiftawa da sauri, idan sun yi nasara.

NOTE:
Don ƙofa mai mahimmanci, tabbatar da an shigar da waya mai hankali kafin yin tambari da shafa a sama.

Yanayin KAWAI KAWAI
Tsohuwar saitin tsarin shine aikin "Maɓalli A Kan Kawai". Tsaron abin hawa yana kunnawa ne kawai lokacin da duk sharuɗɗan suka cika. NOTE: a cikin "Maɓallin Akan Kawai" Yanayin, tsarin zai yi barci a cikin daƙiƙa 15 bayan an kashe abin hawa tare da maɓalli a wurin kashewa. Don canza yanayin aiki zuwa yanayin "Maɓallin Kashe Kawai", dole ne a aiwatar da hanya mai zuwa:

1. Tabbatar ba a amfani da birki na Park tare da Maɓalli a matsayin RUN da KASHE inji.
2. Saka tsarin a cikin yanayin bincike ta hanyar haɗa faifan gwajin TP6 a hankali.
3. Jira module LED1 don gama sigar firmware ta “blink out” kuma duk LEDs sun tsaya tsayin daka.
4. Haɗa faifan gwajin TP6 kuma yayin riƙe ƙasa da Birkin Sabis.
5. Ci gaba da riƙe Birkin Sabis har sai LED3 da LED4 sun kunna a tsaye kuma su bar Birkin Sabis yayin da LED3 da LED4 ke kunne.

NOTE:
Sakin birki na Sabis yayin da LED3 da LED4 har yanzu suna ANA yana saita tsarin zuwa yanayin “Key Off Only”. Ganin cewa sakin birki na Sabis yayin da LED3 da LED4 ke KASHE yana saita tsarin zuwa yanayin “Key On”. Yanayin "Maɓallin Kashe Kawai" zai yi aiki ne kawai idan an shigar da haɗin shigarwar Ƙofa mai hankali.

Shigarwa/Duba Jerin

ILISC515-A (Kofar ɗaga hannu)
Dole ne a yi rajistar masu zuwa bayan shigar da tsarin, don tabbatar da aiki daidai da aminci na ɗagawa. Idan ɗaya daga cikin cak ɗin bai wuce ba, kar a isar da abin hawa. Sake duba duk haɗin kai kamar yadda umarnin shigarwa. NOTE: duba na gaba idan amfani da zaɓin nuni na "Door Ajar".

Fara lissafin da abin hawa a cikin yanayi mai zuwa:

• An ɗagawa
• Ƙofar ɗagawa a rufe
• Saitin birki na Park (PB)
• Watsawa a Park (P)
• Kashe wuta (Maɓalli). Jira har sai module ɗin ya shiga cikin yanayin "Barci" (duk LED LEDs) yana ɗaukar kusan mintuna 5.

MABUDIN BINCIKE: NOTE — zaku iya tsallake wannan sashin idan an saita tsarin don Maɓallin KASHE kawai 

1. Kunna maɓallin kunnawa (zuwa "Run"), tabbatar da cewa tsarin yana farkawa kuma duk LEDs 5 suna kunna kusan 2 seconds. Ƙarƙashin alamar LEDs suna da haske kuma ya kamata su kasance ON a duk lokacin da samfurin ya farka.
2. Tabbatar cewa Wurin Lantarki, Birki na Park, da Shift Lock LED sun kasance a kunne.
3. Ƙoƙarin ƙaddamar da ɗagawa. Dole ne kada a tura ɗagawa tare da Rufe Ƙofar ɗagawa. Na gaba, buɗe ƙofar ɗagawa.
4. Tare da buɗe ƙofar ɗagawa, saitin birki na Park, da watsawa a cikin Park, duk LEDs 5 zasu kasance ON. Ƙoƙarin ƙaddamar da ɗagawa. Tabbatar da aikin ɗagawa. Ajiye dagawa.
5. Tare da buɗe ƙofar ɗagawa da watsawa a cikin Fakin, saki Birkin Fakin. Tabbatar da cewa Wutar Birki ta Park (PB) da Ledojin Tsaron Mota suna kashe, da ƙoƙarin tura ɗagawa. Tabbatar da ɗaga baya turawa.
6. Tare da rufe Ƙofar ɗagawa da saita birki na Park, tabbatar da watsawa ba zai fita daga Park ba.
7. Tare da buɗe Ƙofar ɗagawa kuma an fito da Birkin Park, tabbatar da watsawa ba zai fita daga wurin shakatawa ba.
8. Tare da rufe Ƙofar ɗagawa, an fitar da Birkin Park kuma an yi amfani da Birkin Sabis, tabbatar da cewa za ku iya fita daga Fakin.

BINCIKEN KASHE:

NOTE:
Dole ne ku sami hanyar shigar da birki mai ƙwalƙwalwar Park da Ƙofar ɗagawa don gwajin mai zuwa. Idan ba haka ba, to ana iya tsallake gwajin:

1. Fara da yanayi iri ɗaya na maɓalli na sama sai dai kar a jira module ɗin ya yi barci. Makullin ya kasance a kashe a duk wannan gwajin.
2. Maimaita Matakai 2 - 5 (a sama) don kammala wannan gwajin.
3. Rufe Ƙofar ɗagawa kuma tabbatar da tsarin yana barci bayan 5 min.
4. Bude Ƙofar ɗagawa kuma tabbatar da cewa ƙirar tana farkawa tare da nunin LEDs da ke tabbatarwa; sa'an nan Park, Shift Lock, da Lift Door Buɗe LEDs sun kasance a kunne.

Ƙofar Ajar LED Nuni Panel

Yi rajista iri ɗaya kamar na sama idan kuna amfani da panel Door Ajar. Lokacin da kowace kofa (banda ƙofar ɗagawa) a buɗe take (CAN sensing) ko kuma aka shigar da shigarwar kofa na zaɓi a fil 4 kuma aka ce ƙofar tana BUDE, babban ɓangaren “Door Ajar” zai yi kyaftawa, duk da haka idan ƙofar daga ma a buɗe take. , yana ƙetare kowace kofa kuma yana haskaka sashin a hankali.

Amfani da Module LEDs
Module ɗin yana da LED a kan jirgi guda 5 waɗanda ake amfani da su don isar da bayanai game da aikin na'urar. A cikin yanayin al'ada duk LEDs suna KASHE, amma suna zuwa a yanayi daban-daban:

Kurakurai Aiki
A ƙarƙashin wasu sharuɗɗa, ana amfani da LEDs ɗin don nuna kurakurai waɗanda ke hana ci gaba da aiki. A wannan yanayin, LED Status zai lumshe ido, kuma dangane da wane LEDs aka kunna, ana gano kuskuren kamar haka:

• LED1 ON - Kuskuren saiti akan na'urar fitarwa.
• LED2 ON - Ba a iya saita sadarwar CAN ba
• LED3 ON - Kuskuren fitarwa
• LED 2 & 3 ON - Asarar zirga-zirgar CAN

Kurakurai VIN
Idan akwai kuskure yayin samun VIN abin hawa yayin shigarwa na farko, LEDs 1-4 zai gungurawa sau 2 sannan wani LED zai kunna ID ɗin kuskure kamar haka:

• LED1 ON - Kerarre mara kyau (Ba Ford ba)
• LED2 ON - Chassis mara kyau (Ba Tafiya ba)
• LED3 ON - Injin kuskure
• LED4 ON - Shekarar ƙirar ba daidai ba (Ba samfurin 2015-2018)
• MATSAYI - Bogus VIN (misali duk haruffa iri ɗaya)
• Babu LEDs ON - Babu amsawar VIN

Matsayi
Mutum na iya sanya tsarin a cikin yanayin bincike inda kowane LED ke wakiltar matsayin tsarin. Tsarin yana aiki cikakke a wannan yanayin. Don shigar da yanayin bincike, taɓa waya mai ƙasa zuwa Kushin Gwaji akan tsarin. LEDs za su gungurawa sau biyu, LED1 za su “fita” sigar firmware na yanzu, sannan LEDs za su bayyana matsayin tsarin kamar haka:

• LED 1 ON lokacin da aka kunna Shift Lock.
• LED 2 ON lokacin da watsawa ke cikin wurin shakatawa.
• LED 3 ON lokacin da aka saita birki na Park.
• LED 4 ON lokacin da Ƙofar ɗagawa ta buɗe.
• MATSAYI LED ON yana nuna "Tabbataccen abin hawa" ko "An kunna ɗagawa" ma'ana akwai 12V akan Fin 3 (Wayyan Orange) wanda ke haɗawa da dagawa.
• Yin keken maɓalli zai fita Yanayin Ganewa kuma duk LEDs za su kasance a kashe.

Umarnin Aiki

Bar a Mota
ILISC515-Maɓalli na Shift (Kofar ɗagawa ta Manual) Umarnin Aiki 2015 - 2019 Ford Transit

ILISC515-A (Kofar ɗaga hannu)
ILISC515-A tsari ne na microprocessor don sarrafa aikin ɗaga keken hannu. Tsarin zai yi aiki tare da kunnawa abin hawa ON ko KASHE, (idan an ba da shigarwar birki na birki na zaɓi na zaɓi) ko kuma idan an saita haka, ɗagawar za ta sami kuzari kawai idan Maɓalli ya KASHE. Ana kunna aikin ɗagawa lokacin da ƙayyadaddun yanayin amincin abin hawa ya cika kuma zai kulle watsawa a cikin wurin shakatawa lokacin da hawan keken guragu ke aiki. ILISC515-A yana hana motsin abin hawa daga wurin shakatawa idan ƙofar ɗaga a buɗe take. A matsayin ƙarin fasalin, ba za a iya fitar da abin hawa daga wurin shakatawa ba kowane lokacin da aka taka birki. Wannan yana kawar da wuce gona da iri na birki saboda tuki tare da taka birki.

Maɓallin Aiki:

1. Lokacin da abin hawa ke cikin "Park" LED (P) zai kasance ON.
2. Lokacin da aka yi amfani da birki na Park, LED (PB) zai kasance ON.
3. Lokacin da Ƙofar ɗagawa ta buɗe, LED ɗin Lift Door zai kasance ON. (Ƙofar Ajar LED a kunne (nau'in nuni na zaɓi).
4. Tare da abin hawa a cikin Park kuma ko dai an yi amfani da birki na Park ko Buɗe Ƙofa ko shigar da Kulle Shift na waje, Shift Lock LED zai kasance ON, kuma ba za a iya fitar da watsawa daga Fakin ba.
5. Tare da abin hawa a cikin Park, birki na Park ya yi amfani da ƙofar ɗagawa a buɗe, Ledojin Tsaro na Vehicle zai kasance ON, kuma dagawar zai fara aiki. Duk LEDs za a haskaka a kan kowane nuni panel.

• Ayyukan Maɓalli: (idan an ba da shigar da birki na birki mai mahimmanci da ƙofar ɗagawa)
  • Dole ne abin hawa ya kasance a cikin Fakin kafin a kashe maɓalli.
  • Tare da abin hawa a cikin Park, LED (P) LED da Shift Lock LED za su kasance ON.
  • Tare da amfani da birki na Park kuma an buɗe ƙofar ɗagawa, duk LEDs za su kasance ON, kuma ɗagawa zai fara aiki.
• Nuni na zaɓi:
  Idan an sanye shi da allon nuni na zaɓi na "Door Ajar", babban ɓangaren Door Ajar zai yi ƙiftawa lokacin da kowace kofa (ban da Ƙofar ɗagawa) ta buɗe. Idan Ƙofar dagawa kanta a buɗe take, ɓangaren Door Ajar zai tsaya a tsaye, yana ɗaukar fifiko akan kowace kofa.
• Yanayin Barci:
  Lokacin da aka rufe ƙofar ɗaga kuma an kashe wutar lantarki (Maɓalli), abin hawa na CAN sadarwar zai tsaya bayan jinkiri. Kusan mintuna biyar bayan wannan, tsarin zai shigar da yanayin "barci" mara ƙarancin halin yanzu tare da KASHE duk LEDs. Don farkawa daga yanayin "barci", kunna wutan (maɓalli) ko buɗe ƙofar ɗagawa.
  Duk LEDs nuni za su kunna kusan daƙiƙa 2 a matsayin “tabbatacce”. Ledojin baya na baya suna kan kunne muddin tsarin yana farke.

Ƙunƙarar Yanke Harness

Idan ILISC515-A ya gaza kowane mataki a cikin Gwajin Shigarwa na Post, sakeview umarnin shigarwa kuma duba duk haɗin gwiwa. Idan ya cancanta, kira InterMotive Technical Support a 530-823-1048.

Braun Plug kuma Kunna kayan aikin ɗagawa

Idan ILISC515-A ya gaza kowane mataki a cikin Gwajin Shigarwa na Post, sakeview umarnin shigarwa kuma duba duk haɗin gwiwa. Idan ya cancanta, kira InterMotive Technical Support a 530-823-1048.

Ricon Plug da Play Lift Harness

Idan ILISC515-A ya gaza kowane mataki a cikin Gwajin Shigarwa na Post, sakeview umarnin shigarwa kuma duba duk haɗin gwiwa. Idan ya cancanta, kira InterMotive Technical Support a 530-823-1048.

Braun Plug kuma Yi wasa tare da 2019 Relay Kit

Idan ILISC515-A ya gaza kowane mataki a cikin Gwajin Shigarwa na Post, sakeview umarnin shigarwa kuma duba duk haɗin gwiwa. Idan ya cancanta, kira InterMotive Technical Support a 530-823-1048.

Takardu / Albarkatu

INTERMOTIVE ILISC515-A shine Tsarin Tubar Microprocessor [pdf] Jagoran Jagora ILISC515-A, ILISC515-A Tsarin Tuƙi ne na Microprocessor, Tsarin Tuƙi ne na Microprocessor, Tsarin Tuƙi Microprocessor, Tsarin Tuƙi, Tsari

Magana

• Manual mai amfani