Ulwazi lweMveliso
I-RC-CDFO Isilawuli seGumbi esiSetyenziselwe kwangaphambili
I-RC-CDFO isilawuli segumbi elicwangcisiweyo kwangaphambili ukusuka kwi-Regio Midi series eyenzelwe ukulawula ukufudumeza kunye nokupholisa kwiinkqubo ze-fan-coil. Ibonisa unxibelelwano nge-RS485 (i-Modbus, i-BACnet okanye i-EXOline), uqwalaselo olukhawulezayo nolulula ngeSixhobo seSicelo, ukufakwa lula, kunye nokucima / ukuvala okanye i-0 ... 10 V ukulawula. Umlawuli unomboniso we-backlit kunye negalelo le-detector yokuhlala, uqhagamshelwano lwefestile, inzwa yokudibanisa, okanye utshintsho-umsebenzi. Kwakhona ine-sensor yeqondo lokushisa eyakhelwe ngaphakathi kwaye inokudibaniswa kwinzwa yangaphandle yeqondo lokushisa, ukutshintsha, okanye ukubonelela ukunciphisa ukushisa komoya (PT1000).
Isicelo
Abalawuli beRegio bakulungele ukusetyenziswa kwizakhiwo ezifuna ubutofotofo obuphezulu kunye nokunciphisa ukusetyenziswa kwamandla, njengeeofisi, izikolo, iindawo zokuthenga, izikhululo zeenqwelo moya, iihotele kunye nezibhedlele.
I zixhobo
I-RC-CDFO inokulawula i-0…10 V DC ii-actuator zevalvu kunye/okanye i-24 V AC ye-thermal actuator okanye i-on/off actuators ene-spring return.
Ukuguquguquka noNxibelelwano
I-RC-CDFO inokudityaniswa nenkqubo ye-SCADA ephakathi nge-RS485 (EXOline okanye i-Modbus) kwaye ilungiselelwe isicelo esithile usebenzisa i-software yoqwalaselo yasimahla Isixhobo seSicelo.
Ukubonisa Ukuphatha
Umboniso unezibonakaliso zokufudumeza okanye ukubeka indawo yokupholisa, isalathiso sokulinda, imimiselo yepharamitha yenkonzo, isalathisi esingenamntu / esivaliweyo (kwakwabonisa ubushushu), ubushushu bangaphakathi / bangaphandle, kunye nendawo yokubeka. Umlawuli ukwanendawo yokuhlala, ukunyuka / ukunciphisa, kunye namaqhosha e-fan.
Iindlela zokulawula
I-RC-CDFO inokuqwalasela iindlela ezahlukeneyo zokulawula / ulandelelwano lolawulo, kubandakanywa ukufudumeza, ukufudumeza / ukufudumeza, ukufudumeza okanye ukupholisa ngokutshintsha-umsebenzi, ukufudumeza / ukupholisa, ukufudumeza / ukupholisa nge-VAV-control kunye nokunyanzeliswa komsebenzi wokuhambisa umoya, ukufudumeza / ukupholisa nge-VAV-control, ukupholisa, ukupholisa / ukupholisa, ukufudumeza / ukufudumeza okanye ukupholisa ngokutshintsha, kunye nokutshintsha kunye nomsebenzi we-VAV.
Imiyalelo yokusetyenziswa kwemveliso
Phambi kokufakela kunye nokusebenzisa isilawuli segumbi esele sicwangciswe kwangaphambili seRC-CDFO, nceda ufunde incwadi yomsebenzisi ngononophelo kwaye ulandele imiyalelo enikiweyo.
Ukuhlohla
Uyilo lwemodyuli yoluhlu lweRegio lwabalawuli benza kube lula ukuyifaka kunye nekhomishini. Ukufakela i-RC-CDFO:
- Beka ipleyiti engezantsi eyahlukileyo ukuze ube neentambo kwindawo phambi kokufaka i-electronics.
- Faka umlawuli ngokuthe ngqo eludongeni okanye kwibhokisi yokudibanisa yombane.
Uqwalaselo
I-RC-CDFO inokumiselwa kwisicelo esithile kusetyenziswa iSixhobo seSicelo soqwalaselo lwesoftware. Amaxabiso eparameter angatshintshwa kusetyenziswa INCREASE kunye ne DECREASE amaqhosha kumboniso womlawuli kwaye angqinwe ngeqhosha lokuhlala. Ukuthintela abasebenzisi abangagunyaziswanga ukuba benze utshintsho kwizicwangciso, kunokwenzeka ukuvala umsebenzi weqhosha kunye nokufikelela kwimenyu yeparameter.
Iindlela zokulawula
I-RC-CDFO inokuqwalasela iindlela ezahlukeneyo zolawulo/ulandelelwano lolawulo. Nceda bhekisa kwincwadi yomsebenzisi ngemiyalelo eneenkcukacha yokumisela isilawuli sesicelo sakho.
Ukusetyenziswa
I-RC-CDFO yenzelwe ukulawula ukufudumeza kunye nokupholisa kwiinkqubo ze-fan-coil. Ibonisa unxibelelwano nge-RS485 (i-Modbus, i-BACnet okanye i-EXOline), uqwalaselo olukhawulezayo nolulula ngeSixhobo seSicelo, ukufakwa lula, kunye nokucima / ukuvala okanye i-0 ... 10 V ukulawula. Umlawuli unomboniso we-backlit kunye negalelo le-detector yokuhlala, uqhagamshelwano lwefestile, inzwa yokudibanisa, okanye utshintsho-umsebenzi. Kwakhona ine-sensor yeqondo lokushisa eyakhelwe ngaphakathi kwaye inokudibaniswa kwinzwa yangaphandle yeqondo lokushisa, ukutshintsha, okanye ukubonelela ukunciphisa ukushisa komoya (PT1000). Umboniso unezibonakaliso zokufudumeza okanye ukubeka indawo yokupholisa, isalathiso sokulinda, imimiselo yepharamitha yenkonzo, isalathisi esingenamntu / esivaliweyo (kwakwabonisa ubushushu), ubushushu bangaphakathi / bangaphandle, kunye nendawo yokubeka. Umlawuli ukwanendawo yokuhlala, ukunyuka / ukunciphisa, kunye namaqhosha e-fan. I-RC-CDFO inokulawula i-0…10 V DC ii-actuator zevalvu kunye/okanye i-24 V AC ye-thermal actuator okanye i-on/off actuators ene-spring return. Nceda bhekisa kwincwadi yomsebenzisi ngemiyalelo eneenkcukacha yokumisela isilawuli sesicelo sakho.
I-RC-CDFO isilawuli segumbi esicwangcisiweyo esipheleleyo esivela kuthotho lwe-Regio Midi olujoliswe ukulawula ukufudumeza kunye nokupholisa kwiinkqubo ze-fan-coil.
I-RC-CDFO
Isilawuli segumbi esicwangciswe kwangaphambili esinomboniso, unxibelelwano kunye neqhosha lefeni
- Unxibelelwano nge-RS485 (i-Modbus, i-BACnet okanye i-EXOline)
- Uqwalaselo olukhawulezayo nolulula ngeSixhobo seSicelo
- Ufakelo olulula
- Vula/Vala okanye 0…10 V ulawulo
- Umboniso okhanyisa ngasemva
- Igalelo lomtshini wokuhlala, umfowunelwa wefestile, isivamvo socondensation okanye umsebenzi wokutshintsha
- Unikezelo lokunciphisa ubushushu bomoya
Isicelo
Abalawuli beRegio bafanelekile ukusetyenziswa kwizakhiwo ezifuna ukuthuthuzelwa okuphezulu kunye nokunciphisa ukusetyenziswa kwamandla, njengeeofisi, izikolo, amaziko okuthenga, izikhululo zeenqwelo-moya, iihotele kunye nezibhedlele njl.
Umsebenzi
I-RC-CDFO isilawuli segumbi kuthotho lweRegio. Ineqhosha le-fan-speed control (fan-coil), ukubonisa, kunye nonxibelelwano nge-RS485 (i-Modbus, i-BACnet okanye i-EXOline) yokudibanisa iinkqubo.
Isivamvo
Umlawuli unesixhobo esakhelwe ngaphakathi sobushushu begumbi. I-sensor yangaphandle yeqondo lokushisa kwegumbi, ukutshintshwa-ngaphezulu okanye unikezelo lokunciphisa izinga lokushisa lomoya linokudityaniswa (PT1000).
I zixhobo
I-RC-CDFO inokulawula i-0…10 V DC ii-actuator zevalvu kunye/okanye i-24 V AC ye-thermal actuator okanye i-On/Off actuator ene-spring return.
Ukuguquguquka kunxibelelwano
I-RC-CDFO inokudityaniswa kwinkqubo ye-SCADA ephakathi nge-RS485 (EXOline okanye i-Modbus) kwaye ilungiselelwe isicelo esithile usebenzisa i-software yoqwalaselo yasimahla Isixhobo seSicelo.
Kulula ukuyifaka
Uyilo lwemodyuli, olunepleyiti engezantsi ehlukeneyo yocingo, yenza ukuba lonke uluhlu lweRegio lwabalawuli lula ukuyifaka kunye nekhomishini. Ipleyiti engezantsi inokubekwa endaweni phambi kokuba kufakwe i-electronics. Ukunyuka kwenzeka ngokuthe ngqo eludongeni okanye kwibhokisi yokudibanisa yombane.
Bonisa ukuphatha
Umboniso unezi mpawu zilandelayo:
| 1 | Umlandeli |
| 2 | Isalathiso esizenzekelayo/ngesandla sefeni |
| 3 | Isantya sangoku sabalandeli (0, 1 ,2, 3) |
| 4 | Ukungenisa umoya ngenkani |
| 5 | Ixabiso elitshintshekayo |
| 6 | Isalathisi sokuhlala |
| 7 | Ubushushu begumbi langoku ku°C ukuya kwindawo enye yokugqibela |
| 8 | Vula ifestile |
| 9 | OKUPHOLISA/KUSHISA: Ibonisa ukuba iyunithi ilawula ngokwendawo yokufudumeza okanye yokupholisa |
| 10 | I-STANDBY: Isalathiso sokulinda, INKONZO: Useto lweParameter |
| 11 | VAMILE: Ayinamntu (ikwabonisa iqondo lobushushu) okanye isalathiso sokuValiwe (kucinyiwe kuphela) |
| 12 | Ubushushu bangaphakathi/Ngaphandle |
| 13 | Beka Indawo |
Amaqhosha akwisilawuli enza ucwangciso olulula lwamaxabiso eparameter usebenzisa imenyu yeparameter eboniswe kumboniso. Amaxabiso eparameter atshintshwa ngamaqhosha athi INCREASE ne-DECREASE kwaye utshintsho luqinisekiswa ngeqhosha le-Occupancy.
| 1 | Iqhosha lokuhlala |
| 2 | Yandisa (∧) kunye no Nciphisa (∨) amaqhosha |
| 3 | Iqhosha labalandeli |
Ukuthintela abasebenzisi abangagunyaziswanga ukuba benze utshintsho kwizicwangciso, kunokwenzeka ukuvala ukusebenza kweqhosha. Ufikelelo kwimenyu yeParameter lunokuvaleka.
Iindlela zokulawula
I-RC-CDFO inokuqwalasela iindlela ezahlukeneyo zolawulo/ ulandelelwano lolawulo:
- Ukufudumeza
- Ukufudumeza/Ukufudumeza
- Ukufudumeza okanye ukupholisa ngokutshintsha-umsebenzi
- Ukufudumeza/Ukupholisa
- Ukufudumeza / Ukupholisa kunye nolawulo lwe-VAV kunye nokunyanzeliswa komsebenzi wokubonelela ngomoya
- Ukufudumeza / Ukupholisa nge-VAV-control
- Ukupholisa
- Ukupholisa/Ukupholisa
- Ukufudumeza/Ukufudumeza okanye ukuPholisa ngokutshintsha
- Tshintsha-umsebenzi weVAV
Iindlela zokusebenza
Kukho iindlela ezintlanu ezahlukeneyo zokusebenza: Kuvaliwe, Akuhlali mntu, Yima ngxi, Kuhlalwe kwaye kudlula. Ihleli yimowudi yokusebenza esetwe kwangaphambili. Isetwa ukuba Yima-ngokusebenzisa imenyu yepharamitha ekwidispleyi. Iindlela zokusebenza zinokuvulwa ngomyalelo ophakathi, umtshina wokuhlala okanye iqhosha lokuhlala.
Valiwe: Ukufudumeza kunye nokupholisa kuqhawulwe. Nangona kunjalo, ukukhuselwa kweqabaka kusasebenza (ukusetwa kwefektri (FS))=8°C). Le ndlela iyasebenza ukuba ifestile ivuliwe.
Ayisebenzi: Igumbi apho umlawuli abekwe khona alisetyenziswa ixesha elide, njengeeholide okanye ngeempelaveki ezinde. Zombini izifudumezi kunye nokupholisa zigcinwa kwisithuba sexesha lobushushu obunokulungiseka min/ max amaqondo obushushu aphezulu (FS min=15°C, max=30°C).
Yima ecaleni kuka: Igumbi likwimo yokugcina amandla kwaye alisetyenziswa okwangoku. Oku kunokuba, umzekelo, ngobusuku, ngeempelaveki nangeengokuhlwa. Umlawuli umi ecaleni ukuze atshintshe indlela yokusebenza ukuba i-Occupied ukuba ubukho buchongiwe. Zombini ukufudumeza kunye nokupholisa zigcinwa kwisithuba sexesha lobushushu obulungisekayo min/max amaqondo obushushu aphezulu (FS min=15°C, max=30°C).
Usebenze: Igumbi liyasetyenziswa kwaye imowudi yokuthuthuzela iyasebenza. Umlawuli ugcina ubushushu obujikeleze indawo yokufudumeza (FS=22°C) kunye nendawo yokupholisa (FS=24°C).
Ukugqitha: Iqondo lokushisa kwigumbi lilawulwa ngendlela efanayo kwimodi yokusebenza e-Occupied. Isiphumo sokungenisa umoya ngenkani siyasebenza. Le ndlela yokusebenza iluncedo umzekelo kumagumbi enkomfa, apho abantu abaninzi bekhona ngexesha elinye ixesha elithile. Xa i-Bypass ivuliwe ngokucinezela iqhosha lokuhlala, umlawuli uya kubuyela ngokuzenzekelayo kwimodi yokusebenza kwangaphambili (I-Occupied okanye i-Standby) emva kokuba ixesha elilungelelanisiweyo lidlulile (FS=2 iiyure). Ukuba i-detector yokuhlala isetyenzisiwe, umlawuli uya kubuyela ngokuzenzekelayo kwimowudi yakhe yokusebenza kwangaphambili ukuba akukho ndawo ifunyenweyo kwimizuzu ye-10.
Isikhangeli sokuhlala
Ngokudibanisa i-detector yokuhlala, i-RC-CDFO inokutshintsha phakathi kwemodi yokusebenza esetyenzisiweyo ukuze kubekho (i-Bypass okanye i-Occupied) kunye nemodi yayo yokusebenza kwangaphambili. Ngale ndlela, iqondo lokushisa lilawulwa yimfuno, okwenza kube lula ukugcina amandla ngelixa ugcina ubushushu kwinqanaba elikhululekile.
Iqhosha lokungena
Ukucofa iqhosha lokuhlala ngaphantsi kwemizuzwana emi-5 xa umlawuli ekwimowudi yakhe yokusebenza kwangaphambili kuya kubangela ukuba itshintshele kwimo yokusebenza i-Bypass. Ukucofa iqhosha ngaphantsi kwemizuzwana emi-5 xa isilawuli sikwimowudi ye-Bypass kuya kutshintsha indlela yokusebenza kwimowudi yokusebenza esetwe kwangaphambili Ukuba iqhosha lokuhlala licinezelekile ngaphezu kwemizuzwana emi-5 liza kutshintsha indlela yokusebenza yomlawuli ku-“Cima” (Valiwe/Akubanjwanga). ) nokuba injani na imo yokusebenza yayo yangoku. Isixhobo se-Aplikheyishini okanye isiboniso senza ukuba ukhethe ukuba yeyiphi indlela yokusebenza, Valiwe okanye Ayisetyenziswanga, ekufuneka ivulwe ku-“Cima” (FS=Unoccupied). Ukucofa iqhosha ngaphantsi kwemizuzwana emi-5 xa isilawuli sikwimowudi yokuCima kuya kuyibangela ukuba ibuyele kwimo ye-Bypass.
Ukungenisa umoya ngenkani
I-Regio inomsebenzi owakhelwe ngaphakathi wokungenisa umoya ngenkani. Ukuba imo yokusebenza yokuhlala ilungiselelwe lo msebenzi, ukuvala igalelo le-digital occupancy detector liya kumisela umlawuli kwimowudi ye-Bypass kwaye isebenze imveliso yokungena umoya ngenkani (DO4). Oku kunokusetyenziswa umzekelo ukuvula intengisoamper. Umsebenzi uyayekiswa xa isithuba sokunyanzeliswa esisetatable siphelile.
Umsebenzi wokutshintsha
I-RC-CDFO inegalelo lotshintsho oluseta ngokuzenzekelayo imveliso ye-UO1 ukuze isebenze ngokufudumeza okanye ukupholisa umsebenzi. Igalelo linokudibaniswa kwiinzwa zohlobo lwe-PT1000, kunye ne-sensor ephakanyisiweyo ukwenzela ukuba ibone ukushisa kombhobho wokubonelela ngekhoyili. Ngethuba nje i-valve yokufudumeza ingaphezulu kwe-20% evulekileyo, okanye ixesha ngalinye i-valve yokuzivocavoca iyenzeka, umahluko phakathi kwemidiya kunye nobushushu begumbi ubalwa. Imo yolawulo iyatshintshwa ngokusekwe kumahluko wobushushu. Ngokuzithandela, uqhagamshelwano olunokubakho lwasimahla lunokusetyenziswa. Xa uqhagamshelwano luvulekile, umlawuli uya kusebenza esebenzisa umsebenzi wokufudumeza, kwaye xa uvaliwe usebenzisa umsebenzi wokupholisa.
Ukulawulwa kwesifudumezi sombane
Iimodeli ezinikezela ukusebenza kwefeni zinomsebenzi wokulawula ikhoyili yokufudumeza kwi-UO1 ngokulandelelana kunye nokutshintsha kwi-UO2. Ukuvula lo msebenzi, ipharamitha ye-11 isetyenziselwa ukuseta imo yokulawula "Ukufudumeza / Ukufudumala okanye ukuPholisa ngokutshintsha". Umsebenzi wokutshintsha emva koko uya kusetyenziselwa ukutshintsha phakathi kwemowudi yasehlotyeni nasebusika. I-UO2 iya kusetyenziswa njenge-actuator yokupholisa kwimodi yehlobo kunye ne-actuator yokufudumala kwimodi yasebusika. Xa ikwimo yasehlotyeni, i-RC-CDFO isebenza njengesilawuli sokufudumeza / sokupholisa kwaye xa ikwimo yobusika njengesilawuli sokufudumeza / sokufudumeza. I-UO2 iya kuqalisa kuqala, ilandelwe ngu-UO1 (i-coil yokufudumala).
Ikhoyili yokufudumeza exhunywe kwi-UO1 iya kusebenza kuphela ukuba i-coil kwi-UO2 ayikwazi ukuzalisekisa imfuno yokufudumala ngokwayo.
Phawula ukuba iRegio ayinalo igalelo lokubeka iliso kwimo ye-fan okanye ukufudumeza kwekhoyili yokufudumeza. Le misebenzi kufuneka endaweni yoko ibonelelwe yinkqubo yeSCADA.
Uhlengahlengiso lweseti
Xa ukwimowudi Uhleli, umlawuli usebenza usebenzisa indawo yokufudumeza (FS = 22 ° C) okanye indawo yokupholisa (FS = 24 ° C) enokutshintshwa ngokusebenzisa i-INNCREASE kunye ne-DECREASE amaqhosha. Ukucofa i-INCREASE kuya kwandisa i-setpoint yangoku ngo-0.5 ° C ngokushicilela kude kube yilapho ubuninzi be-offset (FI = + 3 ° C) bufikelelwe. Ukucofa i-DECREASE kuya kunciphisa i-setpoint yangoku nge-0.5 ° C ngokushicilela kude kube yi-offset ephezulu (FI = -3 ° C) ifikeleleke. Ukutshintsha phakathi kweendawo zokufudumeza kunye nokupholisa kwenzeka ngokuzenzekelayo kumlawuli ngokuxhomekeke kwiimfuno zokufudumeza okanye zokupholisa.
Imisebenzi yokhuseleko eyakhelwe-ngaphakathi
I-RC-CDFO inegalelo kwinzwa yocondensation ukuze ibone ukuqokelelana kokufuma. Ukuba ifunyenwe, isekethe yokupholisa iya kunqunyanyiswa. Isilawuli sikwanalo nokhuseleko kwiqabaka. Oku kuthintela umonakalo weqabaka ngokuqinisekisa ukuba ubushushu begumbi alehli ngaphantsi kwe-8°C xa isilawuli sikwimowudi Valiwe.
Unikezelo lokunciphisa ubushushu bomoya
I-AI1 inokuqwalaselwa ukuba isetyenziswe ngenzwa yokunciphisa ubushushu bomoya. Umlawuli wegumbi uya kusebenza kunye kunye nomlawuli wokushisa womoya wokubonelela usebenzisa i-cascade control, okukhokelela ekuboneleleni kweqondo lokushisa lomoya olubaliweyo ukugcina indawo yokushisa kwegumbi. Kuyenzeka ukuseta iisetipoints zomda wemin/max zomda wokufudumeza kunye nokupholisa. Uluhlu lobushushu obumiselweyo: 10…50°C.
Umsebenzi weActuator
Zonke ii-activators ziyasetyenziswa, kungakhathaliseki uhlobo okanye imodeli. Umsebenzi wenziwa ngamaxesha athile, abekwe ngeeyure (FS=23 hours interval). Isiginali yokuvula ithunyelwa kwi actuator ixesha elide njengexesha layo lokuqhuba eliqwalaselweyo. Umqondiso wokuvala uthunyelwa ixesha elilinganayo, emva koko umsebenzi ugqityiwe. Umsebenzi we actuator uyacinywa ukuba ikhefu limiselwe ku-0.
Ulawulo lwabalandeli
I-RC-CDFO ineqhosha lefeni elisetyenziselwa ukuseta isantya sefeni. Ukucofa iqhosha lefeni kuya kubangela ukuba ifeni ihambe kwisantya sayo sangoku ukuya kwesinye.
Umlawuli uneendawo ezilandelayo:
| Ngokuzenzekelayo | Ulawulo oluzenzekelayo lwesantya sefeni ukugcina ubushushu obufunekayo begumbi |
| 0 | Cima ngesandla |
| I | Indawo yezandla enesantya esiphantsi |
| II | Indawo yezandla enesantya esiphakathi |
| III | Isikhundla seManuwali ngesantya esiphezulu |
Kwiindlela zokusebenza Icinyiwe kwaye Ayisetyenziswanga, ifeni iyamiswa nokuba ithini na isicwangciso sokubonisa. Ulawulo lwezandla lwabalandeli lunokuthintelwa ukuba uyafunwa.
Umsebenzi wokunyusa abalandeli
Ukuba kukho umahluko omkhulu phakathi kwendawo yokubeka igumbi kunye nobushushu begumbi langoku, okanye ukuba umntu unqwenela nje ukuva i-fan iqala, umsebenzi wokunyusa unokwenziwa ukuba wenze i-fan ibaleke ngesantya esiphezulu kangangexesha elifutshane lokuqalisa.
Ukukhaba ngabalandeli
Xa usebenzisa abalandeli be-EC banamhlanje abagcina amandla, kusoloko kukho umngcipheko fan akayi kuqalisa ngenxa yolawulo oluphantsi lwevolthi.tage ukuthintela ifeni ekugqithiseni torque yayo yokuqala. Ifeni iya kuhlala imile ngelixa amandla esahamba kuyo, nto leyo enokubangela umonakalo. Ukunqanda oku, umsebenzi wokukhaba kwefeni unokuvulwa. Imveliso yefeni iya kusekwa kwi-100 % ngexesha elimiselweyo (1…10 s) xa ifeni isetiwe ukuba iqhube ngesantya esisezantsi xa iqala ukusuka kwindawo yokucisha. Ngale ndlela, i-torque yokuqala igqithisiwe. Emva kokuba ixesha elimiselweyo lidlulile, ifeni iya kubuyela kwisantya sayo sokuqala.
Imodyuli yokudlulisa, RB3
I-RB3 yimodyuli ye-relay kunye neereyidi ezintathu zokulawula abalandeli kwizicelo ze-fan-coil. Yenzelwe ukuba isetyenziswe kunye ne-RC-…F… abalawuli beemodeli ukusuka kuluhlu lweRegio. Ngolwazi oluthe vetshe, jonga umyalelo we-RB3.
Uqwalaselo kunye nolongamelo usebenzisa iSixhobo sokuSebenzisa
I-RC-CDFO icwangciswe kwangaphambili ekuhanjisweni kodwa ingaqwalaselwa kusetyenziswa isiXhobo seSicelo. Isixhobo seSicelo yinkqubo esekwe kwiPC eyenza kube lula ukuqwalasela nokulawula ukufakela kunye nokutshintsha izicwangciso kusetyenziswa ujongano lomsebenzisi olubanzi. Inkqubo inokukhutshelwa simahla kwiRegin's webindawo www.regincontrols.com.
Idatha yobugcisa
| Ukubonelela ngevoltage | 18…30 V AC, 50…60 Hz |
| Ukusetyenziswa kwangaphakathi | 2.5 VA |
| Ubushushu obugciniwe | 0…50°C |
| Ubushushu bokugcina | -20…+70°C |
| Ukufuma kwendawo | Ubukhulu ngama-90% e-RH |
| Iklasi yokhuseleko | IP20 |
| Unxibelelwano | I-RS485 (i-EXOline okanye i-Modbus ngokufumanisa ngokuzenzekelayo / ukutshintsha-ngaphaya, okanye i-BACnet |
| Modbus | 8 bits, 1 okanye 2 stop bits. Odd, nkqu (FS) okanye akukho mlinganiso |
| I-BACnet | MS/TP |
| Isantya sonxibelelwano | 9600, 19200, 38400 bps (EXOline, Modbus kunye BACnet) okanye 76800 bps (BACnet kuphela) |
| Bonisa | I-LCD ekhanyayo |
| Izinto eziphathekayo, i-casing | Polycarbonate, PC |
| Ubunzima | 110g |
| Umbala | Umqondiso omhlophe RAL 9003 |
Le mveliso inophawu lweCE. Ulwazi oluninzi luyafumaneka ku www.regincontrols.com.
Igalelo
| Inzwa yegumbi langaphandle okanye inzwa yokunciphisa ubushushu bomoya | PT1000 isivamvo, 0…50°C. Abenzi boluvo abafanelekileyo yiRegin's TG-R5/PT1000, TG-UH3/PT1000 kunye neTG-A1/PT1000 |
| I-alt yokutshintsha. uqhagamshelwano olunokubakho | PT1000 isivamvo, 0…100°C. Uluvo olufanelekileyo yiRegin's TG-A1/PT1000 |
| Isikhangeli sokuhlala | Ukuvala uqhagamshelwano olunokubakho. Isibonisi sokuhlala esifanelekileyo yiRegin's IR24-P |
| Uluvo lwe-condensation, umfowunelwa wefestile | Uluvo lwe-Regin lwe-condensation ye-KG-A/1 resp. uqhagamshelwano olunokubakho |
Iziphumo
| I-valve actuator (0…10 V), i-alt. i-actuator ye-thermal (Vula/Vala i-pulsing) okanye Vula/Vala i-actuator (UO1, UO2) | 2 iziphumo | |
| ii-activators zevalvu | 0…10 V, ubuninzi. 5 mA | |
| I actuator yobushushu | 24 V AC, max. 2.0 A (umqondiso wexesha-ngokulinganayo wepulse output) | |
| Vula/Vala i-activator | 24 V AC, max. 2.0 A | |
| Isiphumo | Ukufudumeza, ukupholisa okanye iVAV (damper) | |
| Ulawulo lwabalandeli | 3 iziphumo zesantya I, II kunye III ngokulandelelana, 24 V AC, max 0.5 A | |
| Ukungenisa umoya ngenkani | 24 V AC actuator, max 0.5 A | |
| Yenza umthambo | FS=isithuba seeyure ezingama-23 | |
| Iibhloko zetheminali | Uhlobo lokuphakamisa intambo enkulu yecandelo elinqamlezayo 2.1 mm2 | |
Useto lweendawo ngeSixhobo seSicelo okanye kumboniso
| Indawo yokufudumeza esisiseko | 5…40°C |
| Indawo yokupholisa esisiseko | 5…50°C |
| Ukufuduswa kwendawo | ±0…10°C (FI=±3°C) |
Imilinganiselo
Iintambo
| Indawo yokukhwelela | Ukutyunjwa | Umsebenzi |
| 10 | G | Ukubonelela ngevoltage 24 V AC |
| 11 | G0 | Ukubonelela ngevoltage 0v |
| 12 | I-Do1 | Imveliso yolawulo lwabalandeli I |
| 13 | I-Do2 | Imveliso yolawulo lwabalandeli II |
| 14 | I-Do3 | Imveliso yolawulo lwabalandeli III |
| 20 | yeMfuzo | 24 V AC eqhelekileyo kwi DO |
| 21 | G0 | 0 V eqhelekileyo kwi-UO (ukuba usebenzisa i-0…10 V ii actuators) |
| 22 | I-Do4 | Isiphumo sokungenisa umoya ngenkani |
| 23 | UO1 | Imveliso ye-0…10 i-alt ye-V valve actuator. thermal okanye Vula/Vala i actuator. Ukufudumeza (FS) Ukupholisa okanye ukufudumeza okanye ukuPholisa ngokutshintsha. |
| 24 | UO2 | Imveliso ye-0…10 i-alt ye-V valve actuator. thermal okanye Vula/Vala i actuator. Ukufudumeza, ukuPholisa (FS) okanye Ukufudumeza okanye ukuPholisa ngokutshintsha |
| 30 | I-AI1 | Igalelo lesixhobo sokumisela sangaphandle, alt. inzwa yokunciphisa ubushushu bomoya |
| 31 | UI1 | Igalelo lokutshintsha-ngaphaya koluvo, alt. uqhagamshelwano olunokubakho |
| 32 | DI1 | Igalelo lomtshini wokuhlala, alt. umfowunelwa wefestile |
| 33 | DI2/CI | Igalelo loluvo lweRegin's condensation sensor KG-A/1 alt. tshintsha ifestile |
| 40 | +C | I-24 V DC iqhelekile kwi-UI kunye ne-DI |
| 41 | AGnd | Umhlaba we-analogue |
| 42 | A | RS485-unxibelelwano A |
| 43 | B | RS485-unxibelelwano B |
Amaxwebhu
Onke amaxwebhu anokukhutshelwa kwi www.regincontrols.com.
IOFISI YANKUNDLA ESWEDEN
- Ifowuni: +46 31 720 02 00
- Web: www.regincontrols.com
- I-imeyile: info@regincontrols.com
Amaxwebhu / Izibonelelo
 |
REGIN RC-CDFO Pre Programmed Room Controller kunye noMboniso woNxibelelwano kunye neFan Button [pdf] Incwadi yoMnini I-RC-CDFO, i-RC-CDFO i-Pre Programmed Room Controller kunye noNxibelelwano lokuBonisa kunye neFan Button, i-RC-CDFO Pre Programmed Room Controller, i-RC-CDFO, i-Pre Programmed Room Controller kunye ne-Display Communication kunye neFan Button, isiLawuli seGumbi esiSetyenzisiweyo, uMlawuli wegumbi, uMlawuli weGumbi. |
