Product Information
RC-CDFO Pre-Programmed Room Controller
Iyo RC-CDFO ndeye pre-yakarongwa kamuri controller kubva kuRegio Midi akatevedzana akagadzirirwa kudzora kupisa uye kutonhora mumafan-coil masisitimu. Iyo inoratidzira kutaurirana kuburikidza neRS485 (Modbus, BACnet kana EXOline), nekukurumidza uye nyore kumisikidza kuburikidza neChishandiso Chishandiso, kuisirwa nyore, uye pa/kudzima kana 0…10 V kutonga. Iyo controller ine backlit kuratidza uye inopinza yeoccupancy detector, hwindo kuonana, condensation sensor, kana shanduko-pamusoro basa. Iyo ine zvakare yakavakirwa-mukati mekamuri tembiricha sensor uye inogona kubatanidzwa kune yekunze sensor yekamuri tembiricha, shanduko-pamusoro, kana kupa mhepo tembiricha yekumisa (PT1000).
Application
Iwo maRegio controllers akakodzera kushandiswa muzvivakwa zvinoda kunyaradzwa kwakanyanya uye kuderedzwa kwesimba rekushandisa, senge mahofisi, zvikoro, nzvimbo dzekutengesera, nhandare dzendege, mahotera, uye zvipatara.
Actuators
Iyo RC-CDFO inogona kudzora 0…10 V DC mavharuvhu actuators uye/kana 24 V AC zvinopisa zvinobatidza kana pa/kudzima maakita nekudzoka kwechirimo.
Kuchinjika neKukurukurirana
Iyo RC-CDFO inogona kubatanidzwa kune yepakati SCADA system kuburikidza neRS485 (EXOline kana Modbus) uye yakagadziridzwa kune chaiyo application uchishandisa yemahara configuration software Chikumbiro Chekushandisa.
Display Kubata
Chiratidziro chine zviratidzo zvekudziya kana kutonhora setpoint, standby chiratidzo, sevhisi parameter marongero, isina kugara / kudzima chiratidzo (inoratidzawo tembiricha), mukati / kunze tembiricha, uye setpoint. Iyo controller inewo kugara, kuwedzera / kudzikira, uye mabhatani e fan.
Kudzora Modes
Iyo RC-CDFO inogona kugadziridzwa kune akasiyana ekutonga modhi / kudzora kutevedzana, kusanganisira kupisa, kupisa / kupisa, kupisa kana kutonhora kuburikidza nekuchinja-pamusoro basa, kupisa / kutonhora, kupisa / kutonhora neVAV-kutonga uye kumanikidza kupa mhepo basa, kupisa / kupisa / kutonhora. kutonhora neVAV-kutonga, kutonhora, kutonhora / kutonhora, kupisa / kupisa kana kutonhora kuburikidza nekuchinja-pamusoro, uye kuchinja-pamusoro neVAV basa.
Mirayiridzo Yekushandiswa Kwechigadzirwa
Usati waisa nekushandisa RC-CDFO pre-programmed room controller, tapota verenga bhuku remushandisi zvakanaka uye tevera mirairo yakapiwa.
Installation
Iyo modular dhizaini yeRegio renji yevatongi inoita kuti zvive nyore kuisa uye kutumira. Kuisa iyo RC-CDFO:
- Isa ndiro yepasi yakaparadzana yewaya panzvimbo usati waisa zvemagetsi.
- Isa mutongi zvakananga pamadziro kana pabhokisi rekubatanidza magetsi.
Configuration
Iyo RC-CDFO inogona kugadziridzwa kune chaiyo application uchishandisa yemahara yekumisikidza software Yekushandisa Chishandiso. Iyo parameter value inogona kuchinjwa uchishandisa INCREASE uye DECREASE mabhatani paratidziro yemutongi uye nekusimbiswa nebhatani reOccupancy. Kuti udzivise vashandisi vasina mvumo kubva pakuchinja kune zvigadziriso, zvinokwanisika kuvharira bhatani mashandiro uye parameter menyu yekuwana.
Kudzora Modes
Iyo RC-CDFO inogona kugadziridzwa kune dzakasiyana kudzora modhi / kutonga kutevedzana. Ndokumbira utarise kubhuku remushandisi kuti uwane yakadzama mirairo yekumisikidza controller kune yako chaiyo application.
Usage
Iyo RC-CDFO yakagadzirirwa kudzora kupisa uye kutonhora mumafan-coil masisitimu. Iyo inoratidzira kutaurirana kuburikidza neRS485 (Modbus, BACnet kana EXOline), nekukurumidza uye nyore kumisikidza kuburikidza neChishandiso Chishandiso, kuisirwa nyore, uye pa/kudzima kana 0…10 V kutonga. Iyo controller ine backlit kuratidza uye inopinza yeoccupancy detector, hwindo kuonana, condensation sensor, kana shanduko-pamusoro basa. Iyo ine zvakare yakavakirwa-mukati mekamuri tembiricha sensor uye inogona kubatanidzwa kune yekunze sensor yekamuri tembiricha, shanduko-pamusoro, kana kupa mhepo tembiricha yekumisa (PT1000). Chiratidziro chine zviratidzo zvekudziya kana kutonhora setpoint, standby chiratidzo, sevhisi parameter marongero, isina kugara / kudzima chiratidzo (inoratidzawo tembiricha), mukati / kunze tembiricha, uye setpoint. Iyo controller inewo kugara, kuwedzera / kudzikira, uye mabhatani e fan. Iyo RC-CDFO inogona kudzora 0…10 V DC mavharuvhu actuators uye/kana 24 V AC zvinopisa zvinobatidza kana pa/kudzima maakita nekudzoka kwechirimo. Ndokumbira utarise kubhuku remushandisi kuti uwane yakadzama mirairo yekumisikidza controller kune yako chaiyo application.
RC-CDFO ndeye yakakwana pre-yakarongwa kamuri controller kubva kuRegio Midi akatevedzana akagadzirirwa kudzora kupisa uye kutonhora mune fan-coil masisitimu.
RC-CDFO
Pre-programmed kamuri controller ine kuratidza, kutaurirana uye fan bhatani
- Kukurukurirana kuburikidza neRS485 (Modbus, BACnet kana EXOline)
- Kurumidza uye nyore kugadzirisa kuburikidza neChishandiso Chishandiso
- Easy installation
- On/Off kana 0…10 V control
- Backlit kuratidza
- Input for occupancy detector, hwindo kuonana, condensation sensor kana shanduko-pamusoro basa
- Supply air tembiricha kugumira
Application
Iwo maRegio controllers akakodzera kushandiswa muzvivakwa zvinoda kunyaradzwa kwakanyanya uye kuderedzwa kwesimba rekushandisa, senge mahofisi, zvikoro, nzvimbo dzekutenga, nhandare dzendege, mahotera nezvipatara nezvimwe.
Function
RC-CDFO inodzora kamuri muRegio series. Iine bhatani rechitatu-speed fan control (fan-coil), kuratidza, pamwe nekutaurirana kuburikidza neRS485 (Modbus, BACnet kana EXOline) yekubatanidza masisitimu.
Sensor
Iyo controller ine yakavakirwa-mukati yekamuri tembiricha sensor. Iyo yekunze sensor yekamuri tembiricha, shanduko-pamusoro kana kugovera tembiricha yemhepo inogona zvakare kubatanidzwa (PT1000).
Actuators
RC-CDFO inogona kudzora 0…10 V DC mavharuvhu actuators uye/ kana 24 V AC thermal actuators kana On/Off actuators nechirimo kudzoka.
Kuchinjika nekukurukurirana
RC-CDFO inogona kubatanidzwa kune yepakati SCADA system kuburikidza neRS485 (EXOline kana Modbus) uye yakagadziridzwa kune chaiyo application uchishandisa yemahara configuration software Chikumbiro Chekushandisa.
Easy kuisa
Iyo modular dhizaini, ine yakaparadzana yepasi ndiro yewaya, inoita iyo yese Regio renji revatongi kuve nyore kuisa uye kutumira. Iyo yepasi ndiro inogona kuiswa panzvimbo magetsi asati aiswa. Kukwidza kunoitika zvakananga pamadziro kana pabhokisi rekubatanidza magetsi.
Display kubata
Chiratidziro chine zvinotevera zviratidzo:
| 1 | Fan |
| 2 | Auto / Manual chiratidzo chefani |
| 3 | Ikozvino kumhanya kwefani (0, 1 ,2, 3) |
| 4 | Kufefetedza kunomanikidza |
| 5 | Kuchinja kukosha |
| 6 | Chiratidzo chekugara |
| 7 | Ikozvino tembiricha yekamuri mu °C kusvika kune imwe decimal point |
| 8 | Vhura hwindo |
| 9 | KUTONHORA/KUPISA: Inoratidza kana iyo unit ichitonga zvinoenderana nekudziya kana kutonhora kweseti |
| 10 | STANDBY: Standby chiratidzo, SERVICE: Parameter marongero |
| 11 | KUDZIMA: Kusina basa (inoratidzawo tembiricha) kana Off- chiratidzo (chete OFF) |
| 12 | Kupisa kwemukati/kunze |
| 13 | Setpoint |
Mabhatani ari pa controller anogonesa kusetwa kuri nyore kweparameter values uchishandisa parameter menyu inoratidzwa muchiratidziro. Iyo parameter tsika inoshandurwa neINCREASE uye DECREASE mabhatani uye shanduko dzinosimbiswa nebhatani reOccupancy.
| 1 | Bhatani rekugara |
| 2 | Wedzera (∧) uye Deretsa (∨) mabhatani |
| 3 | Fani bhatani |
Kuti udzivise vashandisi vasina mvumo kubva pakuita shanduko kune zvigadziriso, zvinokwanisika kuvharira bhatani mashandiro. Parameter menyu yekuwana inogona zvakare kuvharwa.
Kudzora modes
RC-CDFO inogona kugadziridzwa kune akasiyana ekudzora modhi / kudzora kutevedzana:
- Kupisa
- Kupisa/Kupisa
- Kupisa kana kutonhora kuburikidza nekuchinja-pamusoro basa
- Kupisa/Kutonhodza
- Kupisa / Kutonhora neVAV-kutonga uye kumanikidzirwa kupa mhepo basa
- Kupisa / Kutonhora neVAV-kutonga
- Kutonhodza
- Kutonhodza/Kutonhodza
- Kupisa / Kupisa kana Kutonhora kuburikidza nekuchinja-pamusoro
- Shandura-pamusoro neVAV basa
Operating modes
Pane nzira shanu dzakasiyana dzekushandisa: Kure, Kusina kugarwa, Kumira-padyo, Kugarwa uye Bypass. Yakagarwa ndiyo preset yekushandisa modhi. Inogona kusetwa kuKumira-nekushandisa iyo parameter menyu muchiratidziro. Maitiro ekushandisa anogona kuvhurwa kuburikidza nekuraira kwepakati, detector yekugara kana bhatani reOccupancy.
Off: Kupisa uye kutonhora kunobviswa. Zvisinei, kudzivirira kwechando kuchiri kushanda (factory setting (FS)) = 8°C). Iyi modhi inovhurwa kana hwindo rakavhurwa.
Vasina basa: Imba inoiswa mutongi haishandiswe kwenguva yakareba, senge panguva yezororo kana kupera kwevhiki. Zvese kupisa nekutonhodza zvinochengetwa mukati menguva yetembiricha ine configurable min/ max tembiricha (FS min=15°C, max=30°C).
Mira ne: Imba yacho iri mumagetsi ekuchengetedza simba uye haisi kushandiswa panguva ino. Izvi zvinogona, semuenzaniso, kuve mukati mehusiku, kupera kwevhiki uye manheru. Iyo controller inomira pedyo kuti ichinje maitiro ekushanda kuti Akabatwa kana kuvepo kwaonekwa. Zvese kupisa nekutonhodza zvinochengetwa mukati menguva yetembiricha ine configurable min/max tembiricha (FS min=15°C, max=30°C).
Basa: Imba iri kushandiswa uye yekunyaradza mode inovhurwa. Mutongi anochengetedza tembiricha yakatenderedza nzvimbo yekudziya (FS=22°C) uye nzvimbo yekutonhodza (FS=24°C).
Bypass: Iyo tembiricha mukamuri inodzorwa nenzira imwecheteyo muOccupied operating mode. Iko kuburitsa kwekumanikidzirwa kufefetera kunoshandawo. Iyi nzira yekushandisa inobatsira semuenzaniso mumakamuri emusangano, umo vanhu vazhinji varipo panguva imwe chete kwenguva yakati. Kana Bypass yaitwa nekudzvanya bhatani rekugara, controller inodzoka otomatiki kune yayo preset yekushandisa modhi (Yakagarwa kana Standby) mushure menguva inogadziriswa yapfuura (FS = maawa maviri). Kana detector yekugara ikashandiswa, controller inongodzokera kune yayo preset yekushandisa mode kana pasina anoonekwa maminetsi gumi.
Occupancy detector
Nekubatanidza detector yekugara, RC-CDFO inogona kushandura pakati peiyo preset yekushanda modhi yekuvapo (Bypass kana Occupied) uye yayo preset inoshanda maitiro. Nenzira iyi, tembiricha inodzorwa nezvinodiwa, zvichiita kuti zvikwanise kuchengetedza simba uchichengetedza tembiricha padanho rakanaka.
Bhatani rekugara
Kudzvanya bhatani rekugara kweasingasviki 5 masekonzi kana controller iri mune yayo preset yekushandisa modhi ichaita kuti ichinje kune inoshanda mode Bypass. Kudzvanya bhatani kweasingasviki 5 masekonzi kana controller iri muBypass modhi ichachinja maitiro ayo ekushandisa kuenda kune yakagara yagara bhatani rekushandisa ) pasinei nekushanda kwayo ikozvino. Chishandiso Chekushandisa kana chiratidziro chinogonesa kusarudza kuti ndeipi modhi yekushandisa, Yakavharwa kana Kusagarwa, inofanirwa kuvhurwa pa "Shutdown" (FS=Unoccupied). Kudzvanya bhatani kweasingasviki masekonzi mashanu kana controller iri muShutdown mode kuchaita kuti idzokere kuBypass mode.
Kufefetedza kunomanikidza
Regio ine yakavakirwa-mukati basa rekumanikidza kufefetera. Kana iyo occupancy operating mode yakagadziridzwa kuitira basa iri, kuvharwa kwe digital occupancy detector kupinza kunoisa mutongi kuBypass mode uye kumisa kubuda kwekumanikidzirwa kufefetera (DO4). Izvi zvinogona semuenzaniso kushandiswa kuvhura adamper. Basa racho rinogumiswa kana iyo setable yekumanikidza interval yapera.
Shanduko-pamusoro basa
RC-CDFO ine chekuisa chekuchinja-pamusoro iyo inogadzirisa otomatiki inobuda UO1 kuti ishande nekudziya kana kutonhora basa. Iyo inopinza inogona kubatanidzwa kune sensors yerudzi PT1000, ine sensor yakaiswa kuitira kuti inzwe tembiricha yepombi yekugovera pombi. Chero bedzi vharuvhu yekudziya inopfuura 20% yakavhurika, kana pese panoitika mavharuvhu, musiyano uripo pakati pemidhiya uye tembiricha yekamuri inoverengerwa. Iyo control mode inozoshandurwa zvichienderana nekusiyana kwekushisa. Sarudzo, inogona-yemahara kuonana inogona kushandiswa. Kana iyo yekubata yakavhurika, mutongi anozoshanda achishandisa kupisa basa, uye kana yakavharwa uchishandisa inotonhorera basa.
Kudzora kwemoto wemagetsi
Mienzaniso inopa kushanda kwefani ine basa rekudzora coil yekudziya paUO1 mukutevedzana nekuchinja-pamusoro paUO2. Kuti uite basa iri, parameter 11 inoshandiswa kuseta nzira yekudzora "Kupisa / Kupisa kana Kutonhora kuburikidza nekuchinja-pamusoro". Iyo shanduko-pamusoro basa rinozoshandiswa kushandura pakati pezhizha nechando modhi. UO2 ichashandiswa seyakatonhodza actuator muchirimo modhi uye seyekudziyisa actuator mumwaka wechando. Kana iri muzhizha modhi, RC-CDFO inoshanda semudziyo wekudziya / kutonhora uye kana iri muchando modhi semudziyo wekudziya / kupisa. UO2 inotanga kutanga, ichiteverwa neUO1 (inopisa coil).
Iyo yekudziya coil yakabatana neUO1 inongoshanda chete kana iyo coil paUO2 isingakwanise kuzadzisa zvinodiwa zvekudziya yega.
Cherechedza kuti Regio haina chekuisa chekutarisa chimiro chefani kana kupisa kweiyo yekudziya coil. Aya mabasa anofanirwa kupihwa neSCADA system.
Setpoint kugadzirisa
Kana iri mumodhi Yakagarwa, mutongi anoshanda achishandisa nzvimbo yekudziya (FS = 22 ° C) kana yekutonhora setpoint (FS = 24 ° C) inogona kuchinjwa uchishandisa INCREASE uye DECREASE mabhatani. Kudzvanya INCREASE kuchawedzera kuseta kwazvino ne 0.5 ° C pamutsikiro kusvika iyo yakanyanya offset (FI=+3°C) yasvikwa. Kudzvanya DECREASE kunoderedza kusetwa kwazvino ne 0.5 ° C paganho rekudhinda kusvika iyo yakanyanya offset (FI=-3 ° C) yasvikwa. Kuchinja pakati pekudziya uye kutonhora kweseti kunoitika otomatiki mune controller zvichienderana nekudziya kana kutonhora zvinodiwa.
Yakavakirwa-mukati kuchengetedza mabasa
RC-CDFO ine yekuisa kune condensation sensor kuti ione kuunganidza hunyoro. Kana ikaonekwa, dunhu rekutonhora rinomiswa. Mutongi anewo kudzivirira kwechando. Izvi zvinodzivirira kukuvadzwa kwechando nekuona kuti tembiricha yemumba haidonhedzi pasi pe8°C kana controller iri mumodhi Off.
Supply air tembiricha kugumira
AI1 inogona kugadzirwa kuti ishandiswe neinopa mhepo tembiricha yekumisa sensor. Mutongi wekamuri anozoshanda pamwe chete neyekugovera tembiricha yemhepo inodzora ichishandisa cascade control, zvichikonzera kuverengerwa kugovera tembiricha yemhepo kuchengetedza tembiricha yekamuri. Izvo zvinogoneka kuseta yega min/max yekumisikidza seti yekudziya uye kutonhora. Settable tembiricha renji: 10…50°C.
Actuator kurovedza
Zvese actuator zvinoitwa, zvisinei nemhando kana modhi. Chiitiko ichi chinoitika panguva dzakasiyana, inogadzika mumaawa (FS = 23 maawa kupindirana). Chiratidzo chekuvhura chinotumirwa kune actuator kwenguva yakareba seyakagadziriswa nguva yekumhanya. Chiratidzo chekuvhara chinotumirwa kwenguva yakaenzana, mushure mezvo basa racho rinopedzwa. Iyo actuator kurovedza inodzimwa kana nguva yacho yakaiswa ku0.
Fan control
RC-CDFO ine bhatani re fan rinoshandiswa kuseta kumhanya kwe fan. Kudzvanya bhatani re fan kuchaita kuti fan ifambe kubva pakumhanya kwayo kuenda kune inotevera.
Mutongi ane zvinzvimbo zvinotevera:
| Auto | Kudzora otomatiki kweiyo fan yekumhanyisa kuchengetedza yaunoda kamuri tembiricha |
| 0 | Manually off |
| I | Manual position ine low speed |
| II | Manual position ine medium speed |
| III | Manual chinzvimbo nekumhanya kukuru |
Mumasevhisi modes Off uye isina kubatwa, iyo fan inomiswa zvisinei neratidziro yekumisikidza. Manual fan control inogona kuvharwa kana uchida.
Fan boost basa
Kana paine musiyano mukuru pakati peseti yekamuri uye tembiricha yekamuri iripo, kana kana munhu achingoda kunzwa fan ichitanga, basa rekusimudzira rinogona kuitwa kuti fan imhanye nekumhanya kwechinguva chidiki-yekutanga.
Fan kickstart
Paunenge uchishandisa anhasi anochengetedza simba eEC mafeni, panogara paine njodzi iyo fan haizotanga nekuda kweiyo low control vol.tage kudzivirira fan kuti isapfuure yayo yekutanga torque. Iyo fan inozoramba yakamira apo simba richiri kuyerera nepakati payo, izvo zvinogona kukonzera kukuvara. Kudzivirira izvi, fan kickstart basa rinogona kuvhurwa. Iyo fan inobuda inozoiswa ku100% yenguva yakatarwa (1…10 s) kana fan yaiswa kuti imhanye nekumhanya kwayo kwakadzikira kana uchitanga kubva panzvimbo. Nenzira iyi, torque yekutanga inopfuudzwa. Mushure mekunge nguva yakatarwa yapera, fan inodzokera kune yayo yekutanga kumhanya.
Relay module, RB3
RB3 iri relay module ine matatu relays ekudzora mafeni mune fan-coil application. Yakagadzirirwa kushandiswa pamwe chete neRC-…F… modhi controller kubva kuRegio renji. Kuti uwane rumwe ruzivo, ona rairo yeRB3.
Kugadzirisa uye kutarisa uchishandisa Chishandiso Chekushandisa
RC-CDFO inofanorongwa pakutumirwa asi inogona kugadzirwa uchishandisa Chishandiso Chekushandisa. Chishandiso Chishandiso chirongwa chePC-chakavakirwa icho chinoita kuti zvikwanise kugadzirisa uye kutarisa kuisirwa uye kushandura marongero ayo uchishandisa yakazara mushandisi interface. Iyo purogiramu inogona kutorwa mahara kubva kuRegin's website www.regincontrols.com.
Technical data
| Mugove voltage | 18…30 V AC, 50…60 Hz |
| Kushandiswa kwemukati | 2.5 VA |
| Ambient tembiricha | 0…50°C |
| Kuchengetedza tembiricha | -20…+70°C |
| Ambient humidity | Kuwedzera 90 % RH |
| Dziviriro kirasi | IP20 |
| Kukurukurirana | RS485 (EXOline kana Modbus ine otomatiki kuona / shanduko-pamusoro, kana BACnet |
| Modbus | 8 bits, 1 kana 2 mira zvishoma. Odd, kunyange (FS) kana pasina parity |
| BACnet | MS/TP |
| Kukurukurirana nokukurumidza | 9600, 19200, 38400 bps (EXOline, Modbus uye BACnet) kana 76800 bps (BACnet chete) |
| Display | Backlit LCD |
| Material, casing | Polycarbonate, PC |
| Kurema | 110g |
| Color | Chiratidzo chichena RAL 9003 |
Ichi chigadzirwa chinotakura CE-mark. Mamwe mashoko anowanika pa www.regincontrols.com.
Inputs
| Yekunze kamuri sensor kana kupa mhepo tembiricha yekumisa sensor | PT1000 sensor, 0…50°C. Masensa akakodzera ndeaya Regin's TG-R5/PT1000, TG-UH3/PT1000 uye TG-A1/PT1000. |
| Shanduko-pamusoro alt. mukana-yemahara kuonana | PT1000 sensor, 0…100°C. Inokodzera sensor ndeye Regin's TG-A1/PT1000 |
| Occupancy detector | Kuvhara kusakwanisa-kusununguka kuonana. Inokodzera detector yekugara iRegin's IR24-P |
| Condensation sensor, hwindo kuonana | Regin's condensation sensor KG-A/1 resp. mukana-kusununguka kuonana |
Outputs
| Varuvha actuator (0…10 V), alt. thermal actuator (On/Off pulsing) kana On/Off actuator (UO1, UO2) | 2 zvabuda | |
| Valve vanoita | 0…10 V, max. 5 mA | |
| Thermal actuator | 24 V AC, max. 2.0 A (nguva-yakaenzana pulse inobuda chiratidzo) | |
| On/Off actuator | 24 V AC, max. 2.0 A | |
| Output | Kupisa, kutonhora kana VAV (damper) | |
| Fan control | 3 kubuda kwekumhanya I, II uye III zvakateerana, 24 V AC, max 0.5 A | |
| Kufefetedza kunomanikidza | 24 V AC actuator, yakawanda 0.5 A | |
| Exercise | FS = maawa makumi maviri nematatu | |
| Terminal blocks | Simudza rudzi rwemax cable cross-section 2.1 mm2 | |
Setpoint marongero kuburikidza neChishandiso Chishandiso kana mukuratidzira
| Basic kudziyisa setpoint | 5…40°C |
| Basic cooling setpoint | 5…50°C |
| Setpoint displacement | ±0…10°C (FI=±3°C) |
Dimensions
Wiring
| Terminal | Designation | Function |
| 10 | G | Mugove voltage 24 V AC |
| 11 | G0 | Mugove voltage 0v |
| 12 | DO1 | Kuburitsa kwe fan control I |
| 13 | DO2 | Kubuda kwe fan control II |
| 14 | DO3 | Kubuda kwe fan control III |
| 20 | GMO | 24 V AC yakajairika kune DO |
| 21 | G0 | 0 V yakajairika yeUO (kana uchishandisa 0…10 V actuators) |
| 22 | DO4 | Kubuda kwekumanikidzira kufefetedza |
| 23 | UO1 | Kubuda kwe0…10 V valve actuator alt. thermal kana On/Off actuator. Kupisa (FS) Kutonhora kana Kupisa kana Kutonhora kuburikidza nekuchinja-pamusoro. |
| 24 | UO2 | Kubuda kwe0…10 V valve actuator alt. thermal kana On/Off actuator. Kupisa, Kutonhodza (FS) kana Kupisa kana Kutonhodza kuburikidza nekuchinja-pamusoro |
| 30 | AI1 | Kupinza kwekunze setpoint mudziyo, alt. kupa mhepo tembiricha yekumisa sensor |
| 31 | UI1 | Input yekuchinja-pamusoro sensor, alt. mukana-kusununguka kuonana |
| 32 | DI1 | Input ye occupancy detector, alt. window contact |
| 33 | DI2/CI | Input yeRegin's condensation sensor KG-A/1 alt. hwindo switch |
| 40 | +C | 24 V DC yakajairika kune UI uye DI |
| 41 | AGnd | Analogue pasi |
| 42 | A | RS485-kutaurirana A |
| 43 | B | RS485-kutaurirana B |
Zvinyorwa
Mapepa ese anogona kutorwa kubva www.regincontrols.com.
HEAD OFFICE SWEDEN
- Nharembozha: +46 31 720 02 00
- Web: www.regincontrols.com
- E-mail: info@regincontrols.com
Zvinyorwa / Zvishandiso
 |
REGIN RC-CDFO Pre Programmed Room Controller ine Display Communication uye Fan Bhatani [pdf] Bhuku reMuridzi RC-CDFO, RC-CDFO Pre Programmed Room Controller ine Display Communication uye Fan Button, RC-CDFO Pre Programmed Room Controller, RC-CDFO, Pre Programmed Room Controller ine Display Communication uye Fan Bhatani, Pre Programmed Room Controller, Room Controller, Controller. |
