Danfoss BOCK UL-HGX12e CO2 LT Reciprocating Compressor

Tlhahisoleseding ya Sehlahiswa

Sehlahisoa ke compressor e phetoang e etselitsoeng lits'ebetso tsa CO2. E fumaneha ka mefuta e fapaneng: UL-HGX12e/20 ML 0,7 CO2 LT, UL-HGX12e/30 ML 1 CO2 LT, UL-HGX12e/40 ML 2 CO2 LT, UL-HGX12e/20 S 1 CO2 LT, UL -HGX12e/30 S 2 CO2 LT, le UL-HGX12e/40 S 3 CO2 LT. Ka kopo hlokomela hore tlhahisoleseding ena e itšetlehile ka boemo ba hona joale ba tsebo 'me e ka fetoha ka lebaka la tsoelo-pele e eketsehileng.

Litaelo tsa Tšebeliso ea Sehlahisoa

Polokeho

• Ho khetholla litaelo tsa polokeho:
  • Kotsi: E supa boemo bo kotsi boo, ha bo sa qojoe, bo tla baka kotsi e bolaeang kapa e mpe hanghang.
  • Tlhokomeliso: E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e mpe.
  • Tlhokomeliso: E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e nyane hanghang.
  • Hlokomela: E supa boemo boo, ha bo sa qojoe, bo ka bakang tšenyo ea thepa.

Khokahano ea Motlakase

Sheba buka ea mosebelisi bakeng sa tlhaiso-leseling e batsi mabapi le khokahano ea motlakase, ho kenyelletsa le tlhaiso-leseling bakeng sa khetho ea sehokahanyi le sehokelo sa motor, khokahano ea koloi e khannang, setšoantšo sa potoloho bakeng sa qalo e tobileng, yuniti ea trigger ea elektroniki INT69 G, khokahano ea yuniti ea trigger ea elektroniki INT69 G. , teko e sebetsang ea yuniti ea elektroniki ea trigger INT69 G, heater ea sump ea oli, khetho le ts'ebetso ea li-converter tsa maqhubu.

Lintlha tsa Tekheniki

• Sheba buka ea mosebelisi bakeng sa lintlha tsa tekheniki mabapi le sehlahisoa.

Litekanyo le Maqhama

• Sheba bukana ea mosebelisi bakeng sa boholo le likhokahano tsa sehlahisoa.

Phatlalatso ea Kenyelletso

• Sheba bukana ea mosebelisi bakeng sa phatlalatso ea kenyelletso.

UL-Setifikeiti sa Tumellano

• Sheba bukana ea mosebelisi bakeng sa UL-Certificate of Compliance.

Ketapele

KOTSI

• Kotsi ea likotsi.
• Li-compressor tsa sehatsetsing ke mechini e hatelletsoeng, ka hona, li hloka tlhokomeliso e matla le tlhokomelo ha li sebetsana.
• Kopano le tšebeliso e fosahetseng ea compressor e ka fella ka kotsi e tebileng kapa e bolaeang!
• Ho qoba kotsi e mpe kapa lefu, ela hloko litaelo tsohle tsa polokeho tse fumanehang litaelong tsena pele u kopanya le pele u sebelisa compressor! Sena se tla qoba ho se utloisisane le ho thibela kotsi e tebileng kapa e bolaeang le tšenyo!
• Le ka mohla u se ke ua sebelisa sehlahisoa ka tsela e fosahetseng empa feela joalokaha u khothalelitsoe ke bukana ena!
• Ela hloko lileibole tsohle tsa polokeho ea lihlahisoa!
• Sheba mekhoa ea mohaho oa lehae bakeng sa litlhoko tsa ho kenya!
• Lisebelisoa tsa CO2 li hloka mofuta o mocha oa tsamaiso le taolo. Ha se tharollo e akaretsang bakeng sa ho nkela sebaka sa F-gase. Ka hona, re bontša ka ho hlaka hore lintlha tsohle tse litaelong tsena tsa kopano li fanoe ho ea ka rona
• boemo ba hona joale ba tsebo 'me e ka fetoha ka lebaka la tsoelo-pele e eketsehileng.
• Litlaleho tsa molao tse ipapisitseng le ho nepahala ha tlhahisoleseling li ke ke tsa etsoa ka nako efe kapa efe mme ka hona li qheletsoe ka thoko.
• Liphetoho tse sa lumelloeng le litokiso ho sehlahisoa se sa kenyelletsoeng bukaneng ena li thibetsoe 'me li tla hlakola waranti!
• Bukana ena ea litaelo ke karolo e tlamang ea sehlahisoa. E tlameha ho fumaneha ho basebetsi ba sebetsang le ba hlokomelang sehlahisoa sena. E tlameha ho fetisetsoa ho bareki ba ho qetela hammoho le yuniti eo compressor e kentsoeng ho eona.
• Tokomane ena e tlas'a tokelo ea molao ea Bock GmbH, Jeremane. Lintlha tse fanoeng bukeng ena li ka fetoha le lintlafatso ntle le tsebiso.

Polokeho

Ho khetholla litaelo tsa polokeho:

KOTSI

• E supa boemo bo kotsi boo, ha bo sa qojoe, bo tla baka kotsi e mpe kapa e mpe hanghang
• E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e mpe
• E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e nyane hanghang.
• E supa boemo boo, ha bo sa qojoe, bo ka bakang tšenyo ea thepa
• Lintlha tsa bohlokoa kapa malebela a ho nolofatsa mosebetsi

Litaelo tse akaretsang tsa polokeho

• Kotsi ea ho bipetsana!
• CO2 ke khase e sa cheng, e nang le asiti, e se nang mebala, e sa nkhang 'me e boima ho feta moea.
• Le ka mohla u se ke ua lokolla melumo ea bohlokoa ea CO2 kapa litaba tsohle tsa sistimi ka likamoreng tse koetsoeng!
• Lisebelisoa tsa polokeho li entsoe kapa li lokisoa ho latela EN 378-2 kapa litekanyetso tse nepahetseng tsa polokeho ea naha.

Kotsi ea ho cha!

• Ho ipapisitsoe le maemo a ts'ebetso, mocheso o kaholimo ho 140 ° F (60 ° C) ka lehlakoreng la khatello kapa ka tlase ho 32 ° F (0 ° C) ka lehlakoreng la ho monya o ka finyelloa.
• Qoba ho kopana le sehatsetsing tlas'a maemo afe kapa afe. Ho kopana le lihatsetsi ho ka lebisa ho cheso e matla le ho halefa ha letlalo.

Tšebeliso e reriloeng

TLHOKOMELO

• Compressor e kanna ea se sebelisoe libakeng tse ka bang le ho phatloha!
• Litaelo tsena tsa kopano li hlalosa mofuta o tloaelehileng oa li-compressor tse boletsoeng sehloohong se entsoeng ke Bock. Li-compressor tsa sehatsetsing sa Bock li etselitsoe ho kenngoa mochining (ka har'a EU ho latela Melao ea EU 2006/42/EC
• Mechine Directive le 2014/68/EU Pressure Equipment Directive, kantle ho EU ho latela melaoana le litataiso tsa naha).
• Ho romelloa ho lumelloa feela haeba li-compressor li kentsoe ho latela litaelo tsena tsa kopano 'me tsamaiso eohle eo li kopantsoeng ho eona e hlahlobiloe le ho amoheloa ho latela melao ea molao.
• Li-compressor li etselitsoe ho sebelisoa le CO2 lits'ebetsong tsa transcritical le/kapa subcritical ho latela meeli ea ts'ebeliso.
• Ho ka sebelisoa feela sehatsetsi se boletsoeng litaelong tsena!
• Tšebeliso efe kapa efe e 'ngoe ea compressor e thibetsoe!

Litšoaneleho tse hlokahalang ho motho

• Basebeletsi ba sa rutehang ka mokhoa o lekaneng ba baka kotsi ea likotsi, phello e ba kotsi e mpe kapa e bolaeang. Ka hona, mosebetsi oa li-compressor o tlameha ho etsoa feela ke basebetsi ba nang le litšoaneleho tse thathamisitsoeng ka tlase:
• mohlala, setsebi sa lihatsetsi kapa moenjiniere oa mechine ea lihatsetsi.
• Hape le liporofeshene tse nang le lithupelo tse bapisoang, tse nolofalletsang basebetsi ho bokella, ho kenya, ho hlokomela le ho lokisa litsi tsa sehatsetsi le li-air-conditioning.
• Basebeletsi ba tlameha ho khona ho lekola mosebetsi o lokelang ho etsoa le ho lemoha likotsi tse ka bang teng.

Tlhaloso ea Sehlahisoa

Tlhaloso e khutšoanyane

• Semi-hermetic lisilindara tse peli tse khutlisetsang compressor e nang le enjene ea ho khanna e pholileng ea khase.
• Ho phalla ha sehatsetsi se kentsoeng ho tsoa ho mouoane ho tsamaisoa holim'a enjene 'me ho fana ka pholileng e matla haholo. Ka hona enjene e ka bolokoa maemong a mocheso a batlang a le tlase haholo nakong ea mojaro o phahameng.
• Pompo ea oli e ikemetseng ntle le tataiso ea ho potoloha bakeng sa phepelo ea oli e tšepahalang le e bolokehileng.
• Belofo e le 'ngoe ea decompression e lehlakoreng le leng le le leng la khatello e tlase le e phahameng, e kenang sepakapakeng ha maemo a khatello e phahameng a fihleloa.

Letlapa la mabitso (mohlalaample)

Libaka tsa kopo

Lihatsetsi

• R744: CO2 (e hlokehang CO2 boleng 4.5 (<5 ppm H2O))

Tefiso ea oli

• Li-compressor li tlatsitsoe fekthering ka mofuta o latelang oa oli: Compressor version ML le S: BOCKlub E85

TSEBISO

• Tšenyo ea thepa e ka etsahala.
• Boemo ba oli bo tlameha ho ba karolong e bonahalang ea khalase ea pono; Tšenyo ea compressor e ka etsahala haeba e tletse kapa e tletse!

Meeli ea kopo

• Ts'ebetso ea compressor e ka khoneha ka har'a meeli ea ts'ebetso. Tsena li ka fumanoa ho sesebelisoa sa khetho sa Bock compressor (VAP) tlasa vap.bock.de. Ela hloko lintlha tse fanoeng moo.
• Mocheso o lumellehang oa tikoloho -4°F … 140°F (-20 °C) – (+60 °C).
• Max. mocheso o lumellehang oa ho qetela oa 320°F (160 °C).
• Min. mocheso qetellong ea ≥ 122 ° F (50 °C).
• Min. oli mocheso ≥ 86°F (30 °C).
• Max. lumello ea ho fetola maqhubu a 12x / h.
• Nako e fokolang ea ho sebetsa ke 3 min. boemo bo tsitsitseng (ts'ebetso e tsoelang pele) e tlameha ho finyelloa.
• Qoba ts'ebetso e tsoelang pele sebakeng se lekanyelitsoeng.
• Max. khatello ea ts'ebetso e lumelletsoeng (LP/HP)1): 1450/1450 psig, 100/100 bar
• LP = Khatello e tlaase HP = Khatello e phahameng

Kopano ea Compressor

• Li-compressor tse ncha li tlatsitsoe ke fektheri ka khase ea inert. Tlohela tefiso ena ea tšebeletso ka har'a compressor nako e telele kamoo ho ka khonehang 'me u thibele ho kena ha moea.
• Sheba sekontiri bakeng sa tšenyo ea lipalangoang pele u qala mosebetsi ofe kapa ofe.

Polokelo le lipalangoang

• Polokelo ho -22°F … 158°F (-30 °C) – (+70 °C), mongobo o phahameng o lumellehang o lekanyelitsoeng 10 % – 95 %, ha ho condensation.
• Se boloke sebakeng se senyang, se lerole, se nang le mouoane kapa sebakeng se chang.
• Sebelisa leihlo la lipalangoang.
• U se ke ua phahamisa ka letsoho!
• Sebelisa lisebelisoa tsa ho phahamisa!

Ho beha

TSEBISO

• Li-attachments (mohlala, li-pipe, li-unit tse eketsehileng, likarolo tse tiisang, joalo-joalo) ka ho toba ho compressor ha lia lumelloa!
• Fana ka tumello e lekaneng bakeng sa mosebetsi oa tlhokomelo. Etsa bonnete ba hore ho na le moea o lekaneng oa compressor.
• Se ke oa e sebelisa sebakeng se senyang, se lerōle, damp sepakapaka kapa tikoloho e chang.
• Seta holim'a bokaholimo kapa foreimi e nang le matla a lekaneng a ho jara.
• Compressor e le 'ngoe ka ho khetheha ho vibrate damper. Khokahano e kopaneng e tiile.

Lihokelo tsa liphaephe

• Tšenyo e ka bang teng.
• Ho chesa haholo ho ka senya valve.
• Ka hona, tlosa litšehetso tsa liphaephe ho tloha ho valve bakeng sa solder, 'me ka hona u pholile 'mele oa valve nakong le ka mor'a ho soasoa. Ke solder feela e sebelisang khase ea inert ho thibela lihlahisoa tsa oxidation (sekala).
• Khokahano ea lisebelisoa tsa tšepe / welding: S235JR
• Lihokelo tsa liphaephe li fumanehile ka har'a li-diameter e le hore liphaephe tse nang le litekanyo tse tloaelehileng li ka sebelisoa.
• Li-diameter tsa khokahanyo tsa li-valve tse koalang li lekantsoe bakeng sa tlhahiso e phahameng ea compressor. Karolo ea 'nete e hlokahalang ea phaephe e tlameha ho tsamaisana le tlhahiso. Hoa tšoana le ho li-valve tse sa khutleng.

Liphaephe

• Liphaephe le likarolo tsa tsamaiso li tlameha ho hloeka le ho omella ka hare le ho se be le sekala, sekoti, le likarolo tsa mafome le phosphate. Sebelisa feela likarolo tse tiisitsoeng ka hermetically.
• Beha lipeipi ka nepo. Li- compensation tse loketseng tsa vibrate li tlameha ho fanoa ho thibela liphaephe hore li se ke tsa phatloha le ho robeha ke ho thothomela ho matla.
• Etsa bonnete ba ho khutlisa oli e nepahetseng.
• Boloka tahlehelo ea khatello ho bonyane bo felletseng.

Li-valve tse koalang (HP/LP)

TLHOKOMELO

• Kotsi ea kotsi.
• Compressor e tlameha ho sithabetsoa ka likhokahano tsa A1 le B1 pele o qala mosebetsi ofe kapa ofe le pele o hokela mochining oa sehatsetsing.

Ho beha methapo ea ho hula le ea khatello

• Tšenyo ea thepa e ka etsahala.
• Liphaephe tse sa kenngoeng hantle li ka baka mapetsong le likhapha, tse ka fellang ka tahlehelo ea sehatsetsing.
• Sebopeho se nepahetseng sa melapo ea ho hula le khatello ka kotloloho ka mor'a hore compressor e be karolo ea ho sebetsa hantle le ho sisinyeha ha sistimi.
• Molao oa letsoho: Kamehla beha karolo ea pele ea liphaephe ho tloha ho valve e koalang ho ea tlase le ho bapela le shaft ea koloi.

Ho sebetsa li-valve tse koalang (mohlalaample)

• Pele o bula kapa o koala belofo e koalang, lokolla valve spindle ka hoo e ka bang. 1/4 ea ho chenchana ka tatellano ea oache.
• Ka mor'a ho kenya valve e koalang, tiisa seal spindle spindle ho ea ka nako.

Mokhoa oa ts'ebetso oa likhokahano tsa lits'ebeletso tse notlehang (mohlalaample)

Ho bula valve ea ho koala:

• Spindle: retelehela ka ho le letshehadi (counter-clockwise) moo e tla ya teng.
• The valve shut-off e ile ea buloa ka ho feletseng / khokahano ea tšebeletso e koetsoe.

Ho bula khokahano ea litšebeletso

• Spindle: Fetolela 1/2 - 1 ho ea ho le letona ho ea ka tšupa-nako.
• Khokahano ea lits'ebeletso e butsoe / valve e koalang e butsoe.
• Ka mor'a ho kenya letsoho, ka kakaretso kenya kepisi ea tšireletso ea spindle hape 'me u tiise ka 40 - 50 Nm. Sena se sebetsa e le tšobotsi ea bobeli ea ho tiisa nakong ea ts'ebetso.

Ho khutla ha oli

• Ho netefatsa hore ts'ebetso ea ho khutlisa oli e tla sebetsa ka ts'epahalo ho sa tsotelehe hore na o sebelisa mofuta oa mofuta ofe oa tlhophiso ea sistimi, Bock e khothaletsa ho kenyelletsa likarohano tsa oli kapa lisebelisoa tsa ho lekola boemo ba oli. Khokahano ea "O" e se e fumaneha fekthering ka sepheo sa ho kenya karolo e 'ngoe ea ho lekola boemo ba oli. Oli e lokela ho khutlisetsoa ho tloha karohanong ea oli ho ea ho compressor ka "D1" e fanoeng bakeng sa morero ona ho compressor.

Sesefa sa peipi ea ho hula

• Bakeng sa litsamaiso tse nang le liphaephe tse telele le tekanyo e phahameng ea tšilafalo, ho kgothaletswa sefe se lehlakoreng la ho hula. Sefefa se tlameha ho nchafatsoa ho latela boemo ba tšilafalo (tahlehelo e fokotsehileng ea khatello).

Khokelo ea motlakase

• Kotsi ea ho tsosoa ke motlakase! Phallo e phahamengtage!
• Etsa mosebetsi feela ha sistimi ea motlakase e khaotsoe phepelong ea motlakase!
• Ha u kopanya lisebelisoa ka thapo ea motlakase, ho tlameha ho bolokoe radius e kobehang bonyane 3x bophara ba cable bakeng sa ho beha mohala.
• Hokela enjene ea compressor ho latela setšoantšo sa potoloho (sheba kahare ho lebokose la terminal).
• Sebelisa litšoelesa tsa cable tse loketseng tsa mofuta o nepahetseng oa tšireletso (sheba poleiti ea mabitso) bakeng sa ho tsamaisa likhoele ka har'a lebokose la theminale. Kenya li-reliefs tsa khatello 'me u thibele matšoao a likhoele holim'a likhoele.
• Bapisa voltage le makhetlo a mangata le data bakeng sa phepelo ea motlakase ea mantlha.
• Hokela enjene feela haeba litekanyetso tsena li tšoana.
• Tlhahisoleseding bakeng sa khetho ea sehokahanyi le motlakase
• Lisebelisoa tsohle tsa ts'ireletso, lisebelisoa le lisebelisoa tsa ho beha leihlo li tlameha ho latela melaoana ea polokeho ea lehae le lintlha tse behiloeng (mohlala, VDE) hammoho le litlhaloso tsa moetsi. Li-switches tsa ts'ireletso ea likoloi lia hlokahala! Likhokahano tsa makoloi, likhoele tsa phepelo, li-fuse le li-switches tsa ts'ireletso ea makoloi li tlameha ho lekanyetsoa ho latela boholo ba hajoale bo sebetsang (sheba poleiti ea mabitso). Bakeng sa ts'ireletso ea enjene, sebelisa sesebelisoa sa ts'ireletso ea moroalo o sebelisoang hona joale, se liehang ho feta nako bakeng sa ho beha leihlo mekhahlelo eohle e meraro. Fetola sesebediswa sa tshireletso ya moroalo o mongata hore se tle se kenngwe tshebetsong nakong ya dihora tse 2 ka makgetlo a 1.2 ho feta ha jwale.

Khokahano ea mochini o khannang

• Compressor e entsoe ka enjene bakeng sa li-circuits tsa star-delta.

Ho qala ha delta ea linaleli ho ka khoneha feela bakeng sa phepelo ea motlakase ea Δ (mohlala 280 V).

ExampLe:

TSEBISO

• Li-insulator tse fanoeng li tlameha ho kenngoa ho latela litšoantšo tse bontšitsoeng.
• Khokahano examptse bonts'itsoeng li bua ka mofuta o tloaelehileng. Tabeng ea voltages, litaelo tse khomaretsoeng lebokoseng la terminal lia sebetsa.

Setšoantšo sa potoloho bakeng sa ho qala ka ho toba 280 V ∆ / 460 VY

BP1	Sesebelisoa sa polokeho ea khatello e phahameng
BP2	Tšireletseho (tekolo e phahameng / e tlase ea khatello)
BT1	Cold conductor (PTC sensor) motor winding
BT2	Thermostat e sireletsang mocheso (sensor ea PTC)
BT3	Sesebelisoa sa ho lokolla (thermostat)
EB1	Mofuthu oa ho futhumatsa oli
EC1	Compressor motor

FC1.1	Phetoho ea tšireletso ea motlakase
FC2	Laola fuse ea potoloho ea matla
INT69 G	Yuniti ea ho bulela elektroniki INT69 G
QA1	Phetoho e kholo
QA2	Net switch
SF1	Taolo voltage switjha

Yuniti ea ho bulela elektroniki INT69 G

• Enjene ea compressor e kentsoe li-sensor tse batang tsa mocheso oa conductor (PTC) tse hokahaneng le yuniti ea trigger ea elektroniki INT69 G ka lebokoseng la terminal. Boemong ba mocheso o feteletseng ha o potoloha enjene, INT69 G e koala sehokelo sa enjene. Ha e se e pholile, e ka qalisoa hape ha senotlolo sa elektroniki sa phepelo ea phepelo (li-terminals B1 + B2) se ka lokolloa ka ho sitisa phano ea phepelo.tage.
• Lehlakore le chesang la khase ea compressor le ka boela la sireletsoa khahlanong le mocheso o feteletseng ka ho sebelisa li-thermostats tsa tšireletso ea mocheso (sesebelisoa).
• Yuniti e tsamaea ha maemo a ts'ebetso a le boima haholo kapa a sa lumelloeng. Fumana le ho lokisa sesosa.
• Sephetho sa relay switching se etsoa joalo ka khokahano e phaphametseng ea phetoho. Potoloho ena ea motlakase e sebetsa ho latela molao-motheo oa hona joale o khutsitseng, ke hore, relay e oela sebakeng se sa sebetseng ebe e tima sekontiri sa enjene leha ho ka ba le khefu ea kutlo kapa potoloho e bulehileng.

Khokahano ea yuniti ea trigger INT69 G

• Hokela yuniti ea trigger INT69 G ho latela setšoantšo sa potoloho. Sireletsa yuniti ea trigger ka fuse e liehang ho sebetsa (FC2) ea max. 4 A. E le ho netefatsa ts'ebetso ea ts'ireletso, kenya mochine oa trigger e le ntho ea pele ho potoloho ea matla a ho laola.

TSEBISO

• Lekanya potoloho ea BT1 le BT2 (sensor ea PTC) ha ea tlameha ho kopana le matla a kantletage.

Teko ea ts'ebetso ea yuniti ea trigger INT69 G

• Pele o laela, ka mor'a ho rarolla mathata kapa ho etsa liphetoho ho potoloho ea matla a taolo, hlahloba ts'ebetso ea "trigger unit". Etsa tlhahlobo ena u sebelisa continuity tester kapa gauge.

	Boemo ba ho lekanya	Boemo ba relay
1.	Boemo bo sa sebetseng	11-12
2.	Ho bulela INT69 G	11-14
3.	Tlosa sehokelo sa PTC	11-12
4.	Kenya sehokelo sa PTC	11-12
5.	Seta bocha ka mor'a ho bulela lithapo tse kholo	11-14

Mofuthu oa ho futhumatsa oli

• E le ho qoba tšenyo ea compressor, compressor e tlameha ho ba le heater ea sump ea oli.
• Sefuthumatsi sa sump ea oli ka kakaretso se tlameha ho hokahanngoa le ho sebetsoa!
• Ts'ebetso: Sefuthumatsi sa sump ea oli se sebetsa ha compressor e eme.
• Ha compressor e qala, ho futhumatsa sump ea oli hoa tima.
• Khokahano: Sefuthumatsi sa sump ea oli se tlameha ho hokeloa ka mohala o thusang (kapa mohala o ts'oanang oa mohala o tšoanang) oa sehokelo sa compressor ho potoloho e arohaneng ea motlakase.
• Lintlha tsa motlakase: 115 V - 1 - 60 Hz, 80 W.

Khetho le ts'ebetso ea li-compressor tse nang le li-converter tsa maqhubu

• Bakeng sa ts'ebetso e bolokehileng ea compressor, converter ea frequency e tlameha ho kenya ts'ebetso e feteletseng ea bonyane 160% ea boholo ba hona joale ba compressor (I-max.) bonyane metsotsoana e 3.
• Ha u sebelisa li-converter tsa frequency, lintlha tse latelang li tlameha ho hlokomeloa:

1. Boholo bo lumelletsoeng ho sebetsa hona joale ba compressor (I-max) (sheba mofuta oa poleiti kapa data ea tekheniki) ha ea lokela ho fetisoa.
2. Haeba ho thothomela ho sa tloaelehang ho etsahala ka har'a sistimi, mefuta e amehang ea frequency converter e tlameha ho koaheloa ka nepo.
3. Phaello e phahameng ka ho fetisisa ea motlakase oa motlakase e tlameha ho ba kholo ho feta boholo ba hona joale ba compressor (I-max).
4. Etsa meralo le lits'ebetso tsohle ho latela melaoana ea ts'ireletso ea lehae le melao e tloaelehileng (mohlala, VDE) le melaoana hammoho le ho latela litlhaloso tsa moetsi oa frequency converter.
5. Mefuta e lumelletsoeng ea maqhubu e ka fumanoa ho data ea tekheniki.

Lebelo la ho potoloha mefuta-futa	0 – f-min	f-min - f-max
Nako ea ho qala	<1 s	ka. 4 s
Nako ea ho emisa	hanghang

• f-min/f-max bona khaolo: Lintlha tsa tekheniki: sebaka se lumelletsoeng sa maqhubu

Ho laela

Litokisetso tsa ho qala

• E le ho sireletsa compressor khahlanong le maemo a sa lumelloeng a ts'ebetso, li-control tse matla le tse tlaase tsa khatello ea li-pressostats li tlamehile ka lehlakoreng la ho kenya.
• Compressor e entse liteko fekthering mme mesebetsi eohle e lekoa. Ka hona, ha ho na litaelo tse khethehileng tsa ho sebetsa.
• Sheba konpresser bakeng sa tšenyo ea lipalangoang!

TLHOKOMELO

• Ha konpresser e sa sebetse, ho itšetlehile ka mocheso o potolohileng le palo ea tefiso ea sehatsetsing, ho ka etsahala hore khatello e ka 'na ea phahama' me ea feta maemo a lumelletsoeng bakeng sa compressor. Litlhokomelo tse lekaneng li tlameha ho nkoa ho thibela sena hore se etsahale (mohlala, ho sebelisa sebaka sa polokelo e batang, tanka ea ho amohela, mochini oa sehatsetsi sa bobeli, kapa lisebelisoa tsa ho fokotsa khatello).

Teko ea matla a khatello

• Compressor e 'nile ea lekoa fekthering bakeng sa botšepehi ba khatello. Haeba leha ho le joalo tsamaiso eohle e lokela ho behoa tekong ea botšepehi ba khatello, sena se lokela ho etsoa ho latela UL-/CSA- Standards kapa tekanyo e tsamaellanang ea polokeho ntle le ho kenngoa ha compressor.

Leak teko

• Kotsi ea ho phatloha!
• Compressor e tlameha ho hatelloa feela ka ho sebelisa nitrogen (N2). Le ka mohla u se ke ua hatella ka oksijene kapa likhase tse ling!
• Khatello e phahameng ka ho fetesisa e lumelletsoeng ea compressor ha ea lokela ho fetisoa ka nako efe kapa efe nakong ea tlhahlobo (sheba data ea poleiti ea mabitso)! Se ke oa kopanya sehatsetsi leha e le sefe le naetrojene kaha sena se ka etsa hore moeli oa ho tima o fetele sebakeng sa bohlokoa.
• Ke likhase tse ommeng feela tse ka sebelisoang bakeng sa tlhahlobo ea ho lutla, mohlala, nitrogen N2 min. 4.6 (= bohloeki 99.996 % kapa ho feta).

Pholoso

• U se ke ua qala compressor haeba e le tlas'a vacuum. U se ke ua sebelisa leha e le efe voltage - esita le bakeng sa liteko (e tlameha ho sebetsoa feela ka sehatsetsing).
• Tlas'a vacuum, bohole ba hona joale ba spark-over le creepage ea liboutu tsa khokahano ea boto ea terminal lia khutsufala; sena se ka fella ka ho senyeha ha boto ea matsoelintsoeke le terminal.
• Ntlha ea pele, tlosa tsamaiso 'me u kenye compressor ts'ebetsong ea ho tlosa. Fokotsa khatello ea compressor.
• Bula li-valve tsa ho koala le ho koala line ea khatello.
• Tlosa hitara ea sump ea oli.
• Tlosa mahlakore a khatello ea ho hula le ho ntša metsi ka pompo ea vacuum.
• Vacuum e tlameha ho rojoa ka naetrojene makhetlo a 'maloa pakeng tsa phallo.
• Qetellong ea ts'ebetso ea ho tsoa, ​​vacuum e lokela ho ba <0.02 psig (1.5 mbar) ha pompo e tima.
• Pheta ts'ebetso ena hangata kamoo ho hlokahalang.

Tefiso ea sehatsetsing

• Apara liaparo tsa boitšireletso tse kang likhalase le liatlana tse itšireletsang!
• Etsa bonnete ba hore li-valve tsa ho koala le tsa khatello li bulehile.
• Ho ipapisitse le moralo oa botlolo ea ho tlatsa sehatsetsing sa CO2 (e nang le / ntle le tubing) CO2 e ka tlatsoa ka mokelikeli kamora boima ba 'mele kapa ka gase.
• Sebelisa feela boleng bo phahameng ba CO2 (sheba khaolo ea 3.1)!
• Ho tlatsa sehatsetsing sa metsi: Ho kgothaletswa hore tsamaiso e tlatsoe pele e eme ka khase ka lehlakoreng le phahameng la khatello ho fihlela khatello ea tsamaiso ea bonyane 75 psig (5.2 bar) (haeba e tlatsitsoe ka tlase ho 75 psig (5.2 bar) ka mokelikeli, ho na le kotsi ea ho thehoa ha leqhoa le omileng). Ho tlatsa ho eketsehileng ho latela tsamaiso.
• Ho felisa monyetla oa ho thehoa ha leqhoa le omileng ha tsamaiso e ntse e sebetsa (nakong le ka mor'a ts'ebetso ea ho tlatsa), sebaka sa ho koala ha mochine o tlaase o lokela ho behoa ho boleng ba bonyane 75 psig (5.2 bar).
• Le ka mohla u se ke ua feta max. likhatello tse dumelletsoeng ha o qosa. Litlhokomeliso li tlameha ho nkoa ka nako.
• Tlatsetso ea sehatsetsing, e ka 'nang ea hlokahala ka mor'a ho qala, e ka kenngoa ka mokhoa oa mouoane ka lehlakoreng la ho monya.
• Qoba ho tlatsa mochine ka sehatsetsing!
• U se ke ua lefisa sehatsetsi sa metsi ka lehlakoreng le monyang holim'a compressor.
• U se ke ua kopanya li-additives le oli le sehatsetsing.

E qalang

• Netefatsa hore li-valve tse koalang ka bobeli li bulehile pele u qala komporo!
• Sheba hore lisebelisoa tsa polokeho le ts'ireletso (switch switch, ts'ireletso ea koloi, mehato ea ts'ireletso ea likhokahano tsa motlakase, joalo-joalo) li sebetsa hantle.
• Tlosa compressor 'me u e lumelle hore e sebetse bonyane metsotso e 10.
• Mochine o lokela ho fihla boemong ba tekano.
• Sheba boemo ba oli: Boemo ba oli bo tlameha ho bonahala ka khalase ea pono.
• Ka mor'a hore compressor e nkeloe sebaka, boemo ba oli bo tlameha ho hlahlojoa hape. Haeba boemo bo phahame haholo, oli e tlameha ho ntšoa (kotsi ea ho sisinyeha ha mokelikeli oa oli; matla a fokotsehileng a sistimi ea sehatsetsi).

TSEBISO

• Haeba palo e kholo ea oli e tlameha ho eketsoa, ​​​​ho na le kotsi ea litlamorao tsa oli. Haeba ho joalo, hlahloba ho khutla ha oli!

Phetoho ea khatello

• Li-switches tsa khatello tse lokisoang ka nepo ho latela UL 207 / EN 378 kapa litekanyetso tsa naha tse timang compressor pele li fihla ho khatello e phahameng e lumelletsoeng ea ts'ebetso li tlameha ho kenngoa tsamaisong. Ho fokotseha ha khatello bakeng sa li-switches tsa khatello ho ka etsahala ebang ke methapo ea ho hula le ea khatello pakeng tsa valve ea ho koala le compressor kapa likhokahano tse sa koalehang bakeng sa li-valve tse koalang (likhokahanyo A le B, bona Khaolo ea 9).

Li-valve tsa khatello ea maikutlo

• Compressor e kentsoe li-valve tse peli tse fokotsang khatello. Belofo e le 'ngoe ka lehlakoreng la ho monya le ho tsoa. Haeba khatello e feteletseng e fihleloa, li-valve lia buleha 'me li thibela ho eketseha ho eketsehileng ha khatello.
• Kahoo CO2 e fefoletsoa sebakeng se haufi!
• Haeba valve ea ho fokotsa khatello e sebetsa khafetsa, hlahloba valve 'me u e khutlisetse haeba ho hlokahala, kaha ho ka hlaha maemo a feteletseng, a ka bakang ho lutla ho sa feleng. Kamehla hlahloba tsamaiso bakeng sa tahlehelo ea sehatsetsi ka mor'a ho kenya ts'ebetso ea valve ea khatello ea khatello!
• Li-valve tsa liphallelo ha li nke sebaka sa li-switches tsa khatello le li-valve tse eketsehileng tsa tšireletso tsamaisong. Li-switches tsa khatello li tlameha ho kengoa ka har'a sistimi le ho raloa kapa ho lokisoa ho latela EN 378-2 kapa litekanyetso tse nepahetseng tsa polokeho.
• Ho hloleha ho ela hloko ho ka baka kotsi ea ho tsoa kotsi ho tloha CO2 e phallang ka ntle ho li-valve tse peli tsa khatello ea khatello!

Ho qoba slugging

• Slugging e ka baka tšenyo ea compressor mme ea etsa hore sehatsetsi se lutle.

Ho thibela slugging:

• Setsi sa sehatsetsi se felletseng se tlameha ho etsoa ka nepo.
• Likarolo tsohle li tlameha ho lekanngoa ka tsela e lumellanang mabapi le tlhahiso (haholo-holo evaporator le li-valve tsa ho atolosa).
• Ho futhumatsa ha khase ea suction ho motsoako oa compressor ho lokela ho ba> 15 K (hlahloba boemo ba valve ea ho atolosa).
• Ela hloko mocheso oa oli le mocheso oa khase ea khatello. (Mocheso oa khase ea khatello e lokela ho ba holimo ka ho lekaneng min. 122 ° F (50 °C), kahoo mocheso oa oli ke> 86 ° F (30 ° C) ).
• Tsamaiso e tlameha ho fihla boemong ba tekano.
• Haholo-holo lits'ebetsong tsa bohlokoa (mohlala, lintlha tse 'maloa tsa mouoane), litekanyo tse kang ts'ebeliso ea maraba a metsi, valve ea solenoid moleng oa mokelikeli, joalo-joalo.
• Ha hoa lokela ho ba le motsamao oa sehatsetsi ka har'a compressor ha sistimi e ntse e eme.

Sefa se omisang

• Gaseous CO2 e na le ho qhibiliha ho tlase haholo metsing ho feta lihatsetsi tse ling. Ka lebaka la mocheso o tlase o ka baka ho thibela li-valve le li-filters ka lebaka la leqhoa kapa hydrate. Ka lebaka lena re khothaletsa-
  lokisa ts'ebeliso ea mochini o omisang sefe e lekaneng boholo bo lekaneng le khalase ea pono e nang le sesupo sa mongobo.

Tlhokomelo

Tokisetso

• Pele o qala mosebetsi ofe kapa ofe oa compressor:
• Tlosa compressor 'me u e sireletse ho thibela ho qala bocha.
• Fokotsa compressor ea khatello ea sistimi.
• Thibela moea ho kena ka har'a sistimi!
• Ka mor'a hore tlhokomelo e etsoe:
• Hokela senotlolo sa polokeho.
• Tlosa compressor.
• Lokolla senotlolo sa ho bulela.
• The decompression e lokela ho etsoa ka tsela ea hore ho se be le leqhoa le omileng ka ho latellana le tiileng CO2 le hlahisoang le thibelang ho tsoa le ho ka sitisa ho phalla ha CO2. Ho seng joalo, ho na le kotsi ea hore khatello e ka tsosolosoa hape.

Mosebetsi o tlameha ho etsoa

• Bakeng sa ho netefatsa ts'epo e nepahetseng ea ts'ebetso le bophelo ba ts'ebeletso ea compressor, re khothaletsa ho etsa ts'ebeletso le ho hlahloba mosebetsi ka linako tse ling:

Ho fetola oli:

• ha e tlamehe bakeng sa litsamaiso tse hlahisoang ke feme.
• bakeng sa lits'ebetso tsa masimong kapa ha o sebetsa haufi le moeli oa kopo: ka lekhetlo la pele kamora lihora tse 100 ho isa ho tse 200 tsa ts'ebetso, ebe hoo e ka bang. lilemo tse ling le tse ling tse 3 kapa lihora tse 10,000 - 12,000 tsa ts'ebetso. Lahla oli e sebelisitsoeng ho latela melaoana; hlokomela melao ea naha.
• Licheke tsa selemo: Boemo ba oli, ho dutla ho thata, lerata le mathang, likhatello, mocheso, ts'ebetso ea lisebelisoa tse thusang joalo ka heater ea sump ea oli, switch switch.

Khothaletso ea karolo ea spare

• Likarolo tse ling tse fumanehang le lisebelisoa li ka fumanoa sesebelisoa sa rona sa khetho sa compressor tlas'a vap.bock.de hammoho le bockshop.bock.de.
• Sebelisa likarolo tsa 'nete tsa Bock feela!

Lisebelisoa

• Bakeng sa ts'ebetso ea CO2 ho hlokahala mefuta e latelang ea oli:
• mofuta oa compressor ML le S: BOCKlub E85

Ho tlosa

• Koala li-valve tse koalang holim'a compressor. CO2 ha e hloke ho sebelisoa hape, ka hona e ka fefoloa tikolohong. Ho bohlokoa ho netefatsa moea o motle kapa ho tsamaisa CO2 kantle ho qoba kotsi ea ho bipetsana. Ha o lokolla
• CO2, qoba ho theoha ka potlako ha khatello ho thibela oli ho tsoa le eona. Haeba konpresser e se na khatello ea maikutlo, tlosa liphaephe tse holim'a khatello le lehlakoreng la ho hula (mohlala, ho qhaqha valve ea ho koala, joalo-joalo) 'me u tlose konpresser ka ho sebelisa mochini o loketseng.
• Lahla oli ka hare ho latela melaoana e sebetsang ea naha.
• Ha ho tlosoa komporo (mohlala, bakeng sa ts'ebeletso kapa ho nkela konpresser sebaka) ho ka lokoloha palo e kholo ea CO2 ka har'a oli. Haeba decompression ea compressor e sa lekana, li-valve tse koetsoeng li ka lebisa khatellong e feteletseng e ke keng ea mamelloa. Ka lebaka lena lehlakore la ho huloa (LP) le lehlakore le phahameng la khatello (HP) la compressor li tlameha ho ts'oaroa ka li-valve tsa decompression.

Lintlha tsa tekheniki

1. Mamello (± 10 %) ha e bapisoa le boleng bo tloaelehileng ba voltage range. Karolo e 'ngoetages le mefuta ea hona joale ka kopo.
2. Litlhaloso tsa max. tšebeliso ea matla e sebetsa bakeng sa ts'ebetso ea 60 Hz.
   • Nahana ka max. e sebetsang hajoale / max. tšebeliso ea matla bakeng sa moralo oa li-fuse, likhoele tsa phepelo le lisebelisoa tsa polokeho. Fuse: Sehlopha sa tšebeliso AC3
3. Litlhaloso tsohle li ipapisitse le karolelano ea voltage fapaneng
4. Sehokelo sa reng bakeng sa li-tubes tsa tšepe
5. Bakeng sa likhokahano tsa solder

Litekanyo le likhokahano

SV DV	Suction line bona data ea tekheniki, khaolo ea 8 Mohala oa ho tsoa
A	Lehlakore la khokahanyo, ha le notleloe	1/8" NPTF
A1	Lehlakore la ho hula la kgokelo, le notlellwang	7/16 “UNF
B	Lehlakore la ho lahla khokahanyo, ha le notleloe	1/8" NPTF
B1	Lehlakore la ho lahla la khokahanyo, le notlelloa	7/16 “UNF
D1	Ho khutla ha oli ea khokahanyo ho tloha karohanong ea oli	1/4" NPTF
E	Tekanyo ea khatello ea oli ea khokahano	1/8" NPTF
F	Sekhahla sa oli	M12x1.5
I	Khokahano ea sensor ea mocheso oa khase e chesang	1/8" NPTF
J	Connection Oil sump heater	3/8" NPTF
K	Khalase e bonang	2 x 1 1/8“ – 18 UNEF
L	Khokahano ea thermostat ea tšireletso ea mocheso	1/8" NPTF
O	Taolo ea boemo ba oli ea khokahano	2 x 1 1/8“ – 18 UNEF
Q	Sensor ea mocheso oa oli ea khokahano	1/8" NPTF
SI1	Decompression valve HP	M22x1.5
SI2	Decompression valve LP	M22x1.5

Phatlalatso ea ho kenyeletsoa

• Phatlalatso ea ho kenngoa ha mochini o sa fellang ho latela EC Machinery Directive 2006/42/EC, Annex II 1. B
• Moetsi: Bock GmbH
• Benzstrasse 7
• 72636 Frikenhausen, Jeremane
• Rona, joalo ka moetsi, re phatlalatsa ka boikarabello ba hore mochini o sa phethahalang
• Lebitso: Semi-hermetic compressor
• Mefuta: HG(X)12P/60-4 S (HC) ………………………HG(X)88e/3235-4(S) (HC)
  UL-HGX12P/60 S 0,7…………………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ……………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ……………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) …………………….. HGX34(P)(e)/380-2 (A)(K)
• HA(X)12P/60-4 ………………………………… HA(X)6/1410-4
• HAX22e/125 LT 2 LG ………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………….. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML(P) 2 CO2T…………. UL-HGX46/440 ML(P) 53 CO2T
• HGZ(X)7/1620-4 …………………………………. HGZ(X)7/2110-4
• HGZ(X)66e/1340 LT 22……………………… HGZ(X)66e/2070 LT 35
• HRX40-2 CO2 TH…………………………….. HRX60-2 CO2 TH
• Lebitso: Bula mofuta oa compressor
• Mefuta: F(X)2 ……………………………………… F(X)88/3235 (NH3)
• FK(X)1……………………………………….. FK(X)3
• FK(X)20/120 (K/N/TK)……………….. FK(X)50/980 (K/N/TK)
• Seriale nomoro: BC00000A001 – BN99999Z999
• Phatlalatso ea ho kenyeletsoa ha mechini e seng e phethiloe ho latela melaoana ea UK Statutory Instrument Supply of Machinery (Safety) 2008, Annex II 1. B.
• Rona, joalo ka moetsi, re phatlalatsa ka boikarabello ba hore mochini o phethiloeng ka karolo e 'ngoe
• Lebitso: Semi-hermetic compressor
• Mefuta: HG(X)12P/60-4 S (HC) ………………………HG(X)88e/3235-4(S) (HC)
• UL-HGX12P/60 S 0,7…………………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ……………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ……………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) …………………….. HGX34(P)(e)/380-2 (A)(K)
• HA(X)22e/125-4 ……………………………….. HA(X)6/1410-4
• HAX22e/125 LT 2 LG ………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………….. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML(P) 2 CO2T…………… UL-HGX46/440 ML(P) 53 CO2T
• HGZ(X)7/1620-4 …………………………………. HGZ(X)7/2110-4
• HGZ(X)66e/1340 LT 22……………………… HGZ(X)66e/2070 LT 35
• HRX40-2 CO2 TH…………………………….. HR(Z)X60-2 CO2 T (H)(V)
• Lebitso: Bula mofuta oa compressor
• Mefuta: F(X)2 ……………………………………………… F(X)88/3235 (NH3)
• FK(X)1…………………………………………….. FK(X)3
• FK(X)20/120 (K/N/TK)……………………….. FK(X)50/980 (K/N/TK)
• Seriale nomoro: BC00000A001 - BN99999Z999

UL-Setifikeiti sa Tumellano

• Moreki ea ratehang, Setifikeiti sa Tumellano se ka khoasolloa ka QR-Code e latelang: https://vap.bock.de/stationaryapplication/Data/
• LitokomaneFiles/COC CO2 trans.pdf

Danfoss A/S Tharollo ea Boemo ba Leholimo

• danfoss.us
• +1 888 326 3677
• heat.cs.na@danfoss.com
• Tlhahisoleseding efe kapa efe, ho kenyeletswa, empa e sa felle feela ho tlhahisoleseding e mabapi le kgetho ya sehlahiswa, tshebediso ya sona kapa tshebediso ya sona, moralo wa sehlahiswa, boima, boholo, bokgoni kapa datha efe kapa efe ya tekheniki e dipukung tsa sehlahiswa, ditlhaloso tsa dikhataloke, dipapatso, jj. le hore na di fumaneha ka mongolo , ka molomo, ka mokhoa oa elektronike, inthaneteng kapa ka mokhoa oa ho jarolla, e tla nkoa e le tsebo, 'me e tlama feela haeba, ho fihlela moo, ho etsoa litšupiso tse hlakileng khotheishene kapa netefatso ea taelo. Danfoss e ke ke ea amohela boikarabello bofe kapa bofe bakeng sa liphoso tse ka bang teng ho li-cataloques, libukana, livideo le lintho tse ling. Danfoss e na le tokelo ea ho fetola lihlahisoa tsa eona ntle le tsebiso. Sena se sebetsa le ho lihlahisoa tse otarang empa li sa tlisoa ha feela liphetoho tse joalo li ka etsoa ntle le liphetoho sebopeho, ho lekana kapa tšebetso ea sehlahisoa.
• Matšoao 'ohle a thepa ena ke thepa ea lik'hamphani tsa Danfoss A/S kapa tsa Danfoss. Danfoss le logo ea Danfoss ke matšoao a khoebo a Danfoss A/S. Litokelo tsohle li sirelelitsoe.

Litokomane / Lisebelisoa

Danfoss BOCK UL-HGX12e CO2 LT Reciprocating Compressor [pdf] Tlhophiso Tataiso BOCK UL-HGX12e CO2 LT Reciprocating Compressor, BOCK UL-HGX12e CO2 LT, Compressor Reciprocating, Compressor

Litšupiso

• Bukana ea Mosebelisi