Danfoss BOCK UL-HGX12e CO2 LT Maimaita Kwamfuta

Bayanin samfur

Samfurin shine kwampreso mai maimaitawa wanda aka tsara don aikace-aikacen CO2. Ana samuwa a cikin nau'i daban-daban: UL-HGX12e/20 ML 0,7 CO2 LT, UL-HGX12e/30 ML 1 CO2 LT, UL-HGX12e/40 ML 2 CO2 LT, UL-HGX12e/20 S 1 CO2 LT, UL -HGX12e/30S 2 CO2 LT, da UL-HGX12e/40 S 3 CO2 LT. Lura cewa wannan bayanin ya dogara ne akan matakin ilimi na yanzu kuma yana iya canzawa saboda ƙarin ci gaba.

Umarnin Amfani da samfur

Tsaro

• Gano umarnin aminci:
  • Hadari: Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai haifar da kisa ko mummunan rauni nan da nan.
  • Gargadi: Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai iya haifar da mutuwa ko mummunan rauni.
  • Tsanaki: Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai iya haifar da mummunan rauni ko ƙananan rauni nan da nan.
  • Lura: Yana nuna yanayin da, idan ba a kauce masa ba, zai iya haifar da lalacewar dukiya.

Haɗin lantarki

Koma zuwa littafin jagorar mai amfani don cikakkun bayanai game da haɗin lantarki, gami da bayani don lamba da zaɓin lamba na mota, haɗin motar tuki, zanen kewayawa don farawa kai tsaye, naúrar faɗakarwa ta lantarki INT69 G, haɗin rukunin faɗakarwar lantarki INT69 G , Gwajin aiki na naúrar faɗakarwa ta lantarki INT69 G, dumama mai, zaɓi da aiki na masu sauya mitar.

Bayanan Fasaha

• Koma zuwa littafin mai amfani don bayanan fasaha akan samfurin.

Girma da Haɗin kai

• Koma zuwa littafin mai amfani don girma da haɗin samfurin.

Sanarwa na Ƙaddamarwa

• Koma zuwa littafin mai amfani don ayyana haɗawa.

UL-Takaddar Yardawa

• Koma zuwa littafin mai amfani don UL- Certificate of Compliance.

Gabatarwa

HADARI

• Hadarin haɗari.
• Kwamfutoci masu firji suna da matsi, don haka, suna kira don ƙarin taka tsantsan da kulawa a cikin kulawa.
• Haɗin da ba daidai ba da amfani da kwampreta na iya haifar da mummunan rauni ko kuma m!
• Don guje wa mummunan rauni ko mutuwa, kiyaye duk umarnin aminci da ke ƙunshe a cikin waɗannan umarnin kafin haɗuwa da kafin amfani da kwampreso! Wannan zai kauce wa rashin fahimtar juna kuma ya hana mummunan rauni da lalacewa!
• Kar a taɓa yin amfani da samfurin ba daidai ba amma kawai kamar yadda wannan jagorar ya ba da shawarar!
• Kula da duk alamun amincin samfur!
• Koma zuwa lambobin ginin gida don buƙatun shigarwa!
• Aikace-aikacen CO2 na buƙatar sabon nau'in tsari da sarrafawa gaba ɗaya. Ba su zama cikakkiyar mafita ba don maye gurbin F-gases. Don haka, muna nuna a fili cewa duk bayanan da ke cikin waɗannan umarnin taro an bayar da su bisa ga namu
• matakin ilimi na yanzu kuma yana iya canzawa saboda ƙarin ci gaba.
• Ba za a iya yin da'awar doka bisa daidaiton bayanin ba a kowane lokaci kuma an cire su gaba ɗaya.
• Canje-canje marasa izini da gyare-gyare ga samfurin da wannan jagorar ba ta rufe su ba an hana su kuma za su ɓata garanti!
• Wannan jagorar koyarwa wani yanki ne na wajibi na samfurin. Dole ne ya kasance samuwa ga ma'aikatan da ke aiki da kula da wannan samfurin. Dole ne a wuce zuwa abokin ciniki na ƙarshe tare da naúrar da aka shigar da compressor.
• Wannan takaddar tana ƙarƙashin haƙƙin mallaka na Bock GmbH, Jamus. Bayanin da aka bayar a cikin wannan jagorar yana iya canzawa da haɓakawa ba tare da sanarwa ba.

Tsaro

Gano umarnin aminci:

HADARI

• Yana nuna yanayi mai haɗari wanda, idan ba a kiyaye shi ba, zai haifar da kisa ko mummunan rauni nan take
• Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai iya haifar da mutuwa ko mummunan rauni
• Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai iya haifar da mummunan rauni ko ƙananan rauni nan da nan.
• Yana nuna yanayin da, idan ba a kauce masa ba, zai iya haifar da lalacewar dukiya
• Muhimmiyar bayanai ko shawarwari akan sauƙaƙe aiki

Gabaɗaya umarnin aminci

• Hadarin shakewa!
• CO2 gas ne mara ƙonewa, acidic, marar launi, kuma iskar da ba ta da wari kuma ya fi iska nauyi.
• Kada a taɓa fitar da babban kundin CO2 ko duka abubuwan da ke cikin tsarin cikin rufaffiyar ɗakuna!
• An ƙirƙira ko daidaita kayan aikin aminci daidai da EN 378-2 ko daidaitattun ƙa'idodin amincin ƙasa.

Hadarin konewa!

• Dangane da yanayin aiki, ana iya kaiwa ga yanayin zafi sama da 140°F (60°C) a gefen matsa lamba ko ƙasa da 32°F (0°C) akan ɓangaren tsotsa.
• Kauce wa lamba tare da refrigerant a kowane hali. Tuntuɓar firji na iya haifar da ƙonawa mai tsanani da haushin fata.

Amfani da niyya

GARGADI

• Maiyuwa ba za a yi amfani da kwampreta a cikin mahalli masu yuwuwar fashewa ba!
• Waɗannan umarnin taro sun bayyana daidaitaccen sigar compressors mai suna a cikin take wanda Bock ya ƙera. Bock compressors an yi niyya don shigarwa a cikin na'ura (a cikin EU bisa ga umarnin EU 2006/42/EC
• Umarnin Injiniya da 2014/68/ EU Matsalolin Kayan Aikin Matsalolin, a wajen EU bisa ga ƙa'idodi da jagororin ƙasa).
• Aiwatar da aiki yana halatta kawai idan an shigar da compressors daidai da waɗannan umarnin taro kuma an bincika kuma an yarda da duk tsarin da aka haɗa su a ciki daidai da ƙa'idodin doka.
• An yi nufin compressors don amfani tare da CO2 a cikin tsarin juzu'i da / ko tsarin ƙima a cikin yarda da iyakokin aikace-aikacen.
• Na'urar firji da aka ƙayyade a cikin waɗannan umarnin kawai za a iya amfani da su!
• An haramta duk wani amfani da kwampreso!

Abubuwan da ake buƙata na ma'aikata

• Rashin cancantar ma'aikata yana haifar da haɗarin haɗari, sakamakon zama mai tsanani ko rauni. Don haka dole ne ma'aikata kawai su yi aiki akan compressors waɗanda ke da cancantar da aka jera a ƙasa:
• misali, injiniyan injin firji ko injin firiji.
• Kazalika da sana'o'i tare da kwatankwacin horo, waɗanda ke ba ma'aikata damar haɗawa, girka, kulawa da gyara na'urorin sanyaya da na'urorin sanyaya iska.
• Dole ne ma'aikata su kasance masu iya tantance aikin da za a gudanar da kuma gane duk wani haɗari mai haɗari.

Bayanin Samfura

Takaitaccen bayanin

• Semi-hermetic biyu-Silinda mai jujjuya kwampreso tare da tsotsa gas sanyaya motar tuki.
• Ruwan firji da aka tsotse daga na'urar mai fitar da ruwa ana jagorantar injin kuma yana samar da sanyaya musamman. Don haka za'a iya ajiye injin akan ƙarancin zafin jiki musamman yayin babban nauyi.
• Ruwan mai mai zaman kansa ba tare da jujjuyawar juyi ba don amintaccen wadataccen mai.
• Bawul ɗin ragewa guda ɗaya kowanne a gefen ƙasan ƙasa da babban matsi, wanda ke huɗawa cikin yanayin yanayi lokacin da matakan matsin lamba ba su yarda ba.

Tambarin suna (misaliample)

Yankunan aikace-aikace

Masu firiji

• R744: CO2 (ƙirar CO2 da ake buƙata 4.5 (<5 ppm H2O))

Kudin mai

• Ana cika kwampressors a masana'anta tare da nau'in mai mai zuwa: nau'in Compressor ML da S: BOCKlub E85

SANARWA

• Lalacewar dukiya yana yiwuwa.
• Matsayin mai dole ne ya kasance a cikin ɓangaren gani na gilashin gani; lalacewa ga kwampreso yana yiwuwa idan an cika shi ko an cika shi!

Iyaka na aikace-aikace

• Ayyukan damfara yana yiwuwa a cikin iyakokin aiki. Ana iya samun waɗannan a cikin kayan zaɓin zaɓi na Bock compressor (VAP) a ƙarƙashin vap.bock.de. Kula da bayanin da aka bayar a can.
• Halatta zafin yanayi -4°F… 140°F (-20°C) – (+60°C).
• Max. halaltaccen zazzabi ƙarshen fitarwa 320°F (160°C).
• Min. zazzabi karshen fitarwa ≥ 122°F (50°C).
• Min. zafin mai ≥ 86°F (30°C).
• Max. halatta mitar sauyawa 12x/h.
• Mafi ƙarancin lokacin gudu na 3 min. Dole ne a cimma daidaiton yanayin (aiki na ci gaba).
• Guji ci gaba da aiki a cikin iyakataccen iyaka.
• Max. halaltaccen matsa lamba (LP/HP) 1): 1450/1450 psig, 100/100 mashaya
• LP = Low-matsi HP = Babban matsa lamba

Compressor taro

• Sabbin kwampressors suna cike da masana'anta da iskar gas mara amfani. Bar wannan cajin sabis a cikin kwampreso har tsawon lokacin da zai yiwu kuma hana shigar da iska.
• Bincika compressor don lalacewar sufuri kafin fara kowane aiki.

Adana da sufuri

• Adana a -22° F
• Kada a adana a cikin gurɓataccen yanayi, ƙura, tururi ko cikin yanayi mai ƙonewa.
• Yi amfani da gashin ido na sufuri.
• Kar a ɗaga da hannu!
• Yi amfani da kayan ɗagawa!

Saita

SANARWA

• Haɗe-haɗe (misali masu riƙe bututu, ƙarin raka'a, sassa masu ɗaure, da sauransu) kai tsaye zuwa kwampreso ba su halatta ba!
• Samar da isasshen izini don aikin kulawa. Tabbatar da isassun iskar compressor.
• Kar a yi amfani da shi a cikin gurɓataccen abu, mai ƙura, damp yanayi ko yanayi mai ƙonewa.
• Saita a kan madaidaicin saman ko firam tare da isassun ƙarfin ɗaukar kaya.
• Single kwampreso zai fi dacewa akan jijjiga damper. Haɗin haɗaɗɗiyar asali m.

Hanyoyin haɗin bututu

• Lalacewa mai yiwuwa.
• Superheating na iya lalata bawul.
• Cire goyan bayan bututu don haka daga bawul don siyar da shi don haka sanyaya jikin bawul yayin da bayan siyarwar. Sai kawai mai siyarwa ta amfani da iskar gas don hana samfuran iskar shaka (ma'auni).
• Haɗin haɗaɗɗen kayan abu / waldawa: S235JR
• Hanyoyin haɗin bututu sun kammala karatunsu a cikin diamita don a iya amfani da bututu masu ma'auni.
• Ana ƙididdige diamita na haɗin haɗin bawul ɗin kashewa don iyakar fitarwar kwampreso. Dole ne a daidaita sashin giciye na bututun da ake buƙata da fitarwa. Hakanan ya shafi bawuloli marasa dawowa.

Bututu

• Bututu da sassan tsarin dole ne su kasance masu tsabta da bushewa a ciki kuma marasa ma'auni, swarf, da yadudduka na tsatsa da phosphate. Yi amfani da sassan da aka rufe kawai.
• Sanya bututu daidai. Dole ne a samar da ma'auni masu dacewa masu dacewa don hana bututu daga fashe da karya ta hanyar girgiza mai tsanani.
• Tabbatar da dawowar mai daidai.
• Ci gaba da asarar matsin lamba zuwa cikakkiyar ƙarancin ƙima.

Flange-kashe bawuloli (HP/LP)

HANKALI

• Hadarin rauni.
• Dole ne a rage matsi ta hanyar haɗin A1 da B1 kafin fara kowane aiki kuma kafin haɗawa da tsarin firiji.

Kwanciya tsotsa da layukan matsa lamba

• Lalacewar dukiya yana yiwuwa.
• Bututun da ba a shigar da shi ba daidai ba zai iya haifar da tsagewa da hawaye, wanda zai iya haifar da asarar na'urar sanyaya.
• Tsarin da ya dace na tsotsawa da layukan matsa lamba kai tsaye bayan kwampreso yana da alaƙa da santsin gudana da yanayin rawar jiki na tsarin.
• Ka'idar babban yatsa: Koyaushe sanya sashin bututu na farko yana farawa daga bawul ɗin kashewa zuwa ƙasa kuma a layi daya zuwa mashin tuƙi.

Yin aiki da bawul ɗin rufewa (misaliample)

• Kafin buɗe ko rufe bawul ɗin rufewa, saki hatimin sandal ɗin bawul ta kusan. 1/4 na juyi counter-clockwise.
• Bayan kunna bawul ɗin kashe-kashe, sake matse hatimin sandal ɗin bawul ɗin daidaitacce a gefen agogo.

Yanayin aiki na haɗin sabis ɗin masu kullewa (misaliample)

Buɗe bawul ɗin kashewa:

• Spindle: juya zuwa hagu (counter-clockwise) gwargwadon yadda zai tafi.
• Bawul ɗin kashewa gabaɗaya ya buɗe / haɗin sabis ɗin ya rufe.

Buɗe haɗin sabis

• Spindle: Juya 1/2 – 1 zuwa hannun dama a agogo.
• An buɗe bawul ɗin rufewa / kashe haɗin sabis.
• Bayan kunna sandar, gabaɗaya sake dacewa da hular kariyar sandar kuma ƙara ƙara da 40 - 50 Nm. Wannan yana aiki azaman fasalin hatimi na biyu yayin aiki.

Mai dawowa

• Don tabbatar da aikin dawo da mai zai yi aiki da dogaro ko da wane nau'in tsarin tsarin da kuke amfani da shi, Bock yana ba da shawarar haɗa masu raba mai ko kayan aikin sa ido kan matakin mai. An riga an sami haɗin haɗin "O" daga masana'anta don manufar shigar da ƙarin sashin kula da matakin mai. Ya kamata a dawo da mai daga mai raba mai zuwa kwampreso ta hanyar haɗin "D1" da aka bayar don wannan dalili akan kwampreso.

Tsotsar bututu tace

• Don tsarin da dogayen bututu da mafi girman matakin gurɓatawa, ana ba da shawarar tacewa a gefen tsotsa. Dole ne a sabunta matatar ta dangane da girman gurɓataccen abu (rage asarar matsa lamba).

Haɗin lantarki

• Hadarin girgiza wutar lantarki! Babban voltage!
• Yi aiki kawai lokacin da tsarin lantarki ya katse daga wutar lantarki!
• Lokacin haɗa na'urorin haɗi tare da kebul na lantarki, dole ne a kiyaye mafi ƙarancin radius na lanƙwasawa na 3x diamita na USB don shimfiɗa kebul ɗin.
• Haɗa injin kwampreta daidai da zanen kewayawa (duba cikin akwatin tasha).
• Yi amfani da ginshiƙan igiyoyi masu dacewa na daidaitaccen nau'in kariya (duba farantin suna) don jigilar igiyoyi cikin akwatin tasha. Saka abubuwan rage damuwa kuma ka hana alamun chafe akan igiyoyi.
• Kwatanta voltage da ƙimar mitar tare da bayanai don wadatar wutar lantarki.
• Haɗa motar kawai idan waɗannan dabi'u iri ɗaya ne.
• Bayani don lambar sadarwa da zaɓin lamba na mota
• Duk kayan kariya, sauyawa da na'urorin sa ido dole ne su bi ka'idodin aminci na gida da ƙayyadaddun ƙayyadaddun bayanai (misali VDE) da ƙayyadaddun masana'anta. Ana buƙatar maɓallan kariyar mota! Dole ne a ƙididdige masu tuntuɓar motoci, layin ciyarwa, fis da maɓallan kariyar mota bisa ga matsakaicin matsakaicin aiki na yanzu (duba farantin suna). Don kariyar mota, yi amfani da na'urar kariyar abin da ta dogara da yanzu, mai jinkirin lokaci don sa ido kan dukkan matakai guda uku. Daidaita na'urar kariya ta nauyi ta yadda dole ne a kunna ta a cikin sa'o'i 2 a sau 1.2 matsakaicin aiki na yanzu.

Haɗin motar tuƙi

• An ƙera compressor tare da injin don da'irar tauraro-delta.

Farawar tauraro-delta yana yiwuwa ne kawai don samar da wutar lantarki Δ (misali 280V).

Exampda:

BAYANI

• Dole ne a ɗora insulators ɗin da aka kawo bisa ga hotunan da aka nuna.
• Haɗin tsohonamples nuna koma ga daidaitaccen sigar. A cikin yanayi na musamman voltage, umarnin da aka makala a akwatin tashar yana aiki.

Tsarin kewaya don farawa kai tsaye 280V ∆ / 460 VY

BP1	Babban matsi mai kula da tsaro
BP2	Sarkar tsaro (sabi mai girma/ƙananan matsa lamba)
BT1	Cold conductor (PTC firikwensin) iska
BT2	Thermal kariya ma'aunin zafi da sanyio (PTC firikwensin)
BT3	Canjin fitarwa (thermostat)
Farashin EB1	Mai dumama dumama
Saukewa: EC1	Injin Compressor

FC1.1	Motar kariya ta sauya
FC2	Sarrafa fis ɗin kewaya wutar lantarki
INT69 G	Naúrar faɗakarwa Electronic INT69 G
QA1	Babban canji
QA2	Mai sauya hanyar sadarwa
SF1	Sarrafa voltage canza

Naúrar faɗakarwa Electronic INT69 G

• Motar ta kwampreso tana sanye da na'urori masu auna zafin jiki na sanyi (PTC) da aka haɗa zuwa naúrar faɗakarwa ta lantarki INT69 G a cikin akwatin tasha. Idan akwai matsanancin zafin jiki a cikin iskar motar, INT69 G yana kashe mai tuntuɓar motar. Da zarar an sanyaya, za a iya sake kunna shi kawai idan kulle lantarki na relay na fitarwa (tashoshi B1+B2) an sake shi ta hanyar katse wutar lantarki.tage.
• Hakanan za'a iya kiyaye gefen gas mai zafi na compressor daga zafin jiki ta amfani da ma'aunin zafi da sanyio (na'urorin haɗi).
• Naúrar tana yin tafiye-tafiye lokacin da abin hawa ko yanayin aiki mara izini ya auku. Nemo ku gyara sanadin.
• Ana aiwatar da fitarwa na sauyawar gudun ba da sanda azaman lambar sadarwa mai sauyawa. Wannan da'irar lantarki tana aiki bisa ga ƙa'idar halin yanzu, watau gudun ba da sanda ya faɗo zuwa wurin da ba shi da aiki kuma yana kashe mai tuntuɓar motar koda kuwa an sami hutun firikwensin ko buɗe kewaye.

Haɗin naúrar faɗakarwa INT69 G

• Haɗa naúrar faɗakarwa INT69 G daidai da zane-zane. Kare naúrar faɗakarwa tare da jinkirin fuse (FC2) na max. 4 A. Domin tabbatar da aikin kariyar, shigar da naúrar faɗakarwa a matsayin kashi na farko a cikin da'irar wutar lantarki.

SANARWA

• Dole ne a auna kewaye BT1 da BT2 (PTC firikwensin) kada su haɗu da vol na wajetage.

Gwajin aikin naúrar jawo INT69 G

• Kafin ƙaddamarwa, bayan gyara matsala ko yin canje-canje ga da'irar wutar lantarki, duba aikin naúrar faɗakarwa. Yi wannan cak ta amfani da ma'aunin ci gaba ko ma'auni.

	Jihar ma'auni	Matsayin gudu
1.	Yanayin kashewa	11-12
2.	Saukewa: INT69G	11-14
3.	Cire haɗin PTC	11-12
4.	Saka mai haɗin PTC	11-12
5.	Sake saitin bayan an kunna mains	11-14

Mai dumama dumama

• Domin gujewa lalacewa da kwampreso, dole ne a sanye da kwampreso da na'urar dumama mai.
• Dole ne a haɗa dumama dumama man da kuma sarrafa shi!
• Aiki: Na'urar dumama mai tana aiki lokacin da kwampreta ya tsaya cik.
• Lokacin da kwampreso ya fara tashi, dumama tarin mai yana kashewa.
• Haɗin kai: Dole ne a haɗa mahaɗar dumbin mai ta hanyar haɗin gwiwa (ko lambar sadarwa mai haɗaɗɗiya ta layi daya) na mai tuntuɓar kwampreso zuwa wani keɓaɓɓen da'irar lantarki.
• Bayanan lantarki: 115 V - 1 - 60 Hz, 80 W.

Zaɓi da aiki na compressors tare da masu juyawa mita

• Don amintaccen aiki na kwampreso, mai sauya mitar dole ne ya sami damar yin amfani da nauyi na aƙalla 160% na matsakaicin halin yanzu na compressor (I-max.) na aƙalla daƙiƙa 3.
• Lokacin amfani da masu sauya mitar, dole ne kuma a lura da abubuwa masu zuwa:

1. Matsakaicin halattaccen aiki na yanzu na kwampreso (I-max) (duba nau'in farantin karfe ko bayanan fasaha) dole ne a ƙetare shi.
2. Idan girgizar da ba ta dace ba ta faru a cikin tsarin, mitar mitar da abin ya shafa a cikin mai sauya mitar dole ne a cire ta yadda ya kamata.
3. Matsakaicin abin da ake fitarwa na mai sauya mitar dole ne ya zama mafi girma fiye da matsakaicin halin yanzu na compressor (I-max).
4. Yi duk ƙirƙira da shigarwa daidai da ƙa'idodin aminci na gida da ƙa'idodi gama gari (misali VDE) da ƙa'idodi da kuma daidai da ƙayyadaddun masana'anta na mai sauya mitar.
5. Ana iya samun kewayon mitar da aka halatta a cikin bayanan fasaha.

Gudun juyawa iyaka	0 - f min	f-min - f-max
Lokacin farawa	<1 s	ca. 4s ku
Lokacin kashewa	nan da nan

• f-min/f-max duba babi: Bayanan fasaha: halattaccen kewayon mitar

Gudanarwa

Shirye-shiryen farawa

• Don kare kwampreso daga yanayin aiki maras amfani, babban matsi da ƙananan matsi da matsi masu mahimmanci suna da mahimmanci a gefen shigarwa.
• Compressor ya yi gwaji a masana'anta kuma an gwada dukkan ayyuka. Don haka babu umarnin shiga na musamman.
• Duba compressor don lalacewar sufuri!

GARGADI

• Lokacin da kwampreso ba ya gudana, dangane da yanayin zafi da adadin cajin firiji, yana yiwuwa matsa lamba na iya tashi kuma ya wuce matakan da aka halatta don kwampreso. Dole ne a ɗauki isassun matakan kariya don hana faruwar hakan (misali ta yin amfani da wurin ajiyar sanyi, tanki mai karɓa, na'urar firji na biyu, ko na'urorin agajin matsa lamba).

Gwajin ƙarfin matsi

• An gwada compressor a cikin masana'anta don amincin matsi. Idan duk da haka za a yi gwajin amincin matsi gabaɗayan tsarin, ya kamata a aiwatar da wannan daidai da ka'idodin UL-/CSA- ko daidaitaccen ma'aunin aminci ba tare da haɗa da kwampreso ba.

Gwajin zubewa

• Hadarin fashewa!
• Dole ne kawai a matsi da kwampreso ta amfani da nitrogen (N2). Kada a taɓa matsawa da iskar oxygen ko wasu iskar gas!
• Matsakaicin izinin wuce gona da iri na compressor ba dole ba ne a wuce shi a kowane lokaci yayin aikin gwaji (duba bayanan farantin suna)! Kada a haxa duk wani abin sanyi da nitrogen saboda wannan zai iya haifar da iyakar ƙonewa zuwa kewayo mai mahimmanci.
• Busassun busassun iskar gas za a iya amfani da su don gwajin yaɗuwar, misali nitrogen N2 min. 4.6 (= tsarki 99.996% ko sama).

Ficewa

• Kada a fara kwampreso idan yana ƙarƙashin injin. Kar a yi amfani da kowane voltage – har ma don dalilai na gwaji (dole ne a yi aiki da shi tare da firji kawai).
• Ƙarƙashin vacuum, ɓangarorin walƙiya da tazara a halin yanzu na ƙusoshin haɗin jirgi na tasha suna gajarta; wannan na iya haifar da iska da lalacewa ta tashar jirgin ruwa.
• Da farko fitar da tsarin sannan kuma haɗa da kwampreso a cikin aikin ƙaura. Sauke matsa lamba na kwampreso.
• Bude igiyar tsotsa da matsi na kashe bawuloli.
• Kunna dumama mai.
• Fitar da tsotsa da ɓangarorin matsewa ta amfani da famfo.
• Dole ne a karya injin tare da nitrogen sau da yawa tsakanin ƙaura.
• A ƙarshen aikin fitarwa, injin ya kamata ya zama <0.02 psig (1.5 mbar) lokacin da aka kashe famfo.
• Maimaita wannan tsari sau da yawa kamar yadda ake buƙata.

Cajin firiji

• Saka kayan kariya na sirri kamar tabarau da safar hannu masu kariya!
• Tabbatar cewa tsotsawa da layin rufewa a buɗe suke.
• Dangane da ƙira na CO2 kwalabe mai cike da sanyi (tare da / ba tare da tubing ba) CO2 za a iya cika shi da ruwa bayan nauyi ko gas.
• Yi amfani da ingancin CO2 mai bushewa kawai (duba babi 3.1)!
• Cika refrigerant na ruwa: Ana ba da shawarar cewa tsarin farko ya cika a tsaye tare da iskar gas a kan babban matsi har zuwa tsarin tsarin na akalla 75 psig (5.2 bar) (idan an cika shi a kasa 75 psig (5.2 bar) tare da ruwa, akwai haɗarin busasshen ƙanƙara). Ci gaba da cikawa bisa ga tsarin.
• Don kawar da yiwuwar busassun ƙanƙara lokacin da tsarin ke aiki (lokacin da kuma bayan aikin cikawa), ya kamata a saita maɓallin kashewa na ƙananan matsi zuwa darajar akalla 75 psig (5.2 bar).
• Kar a taɓa wuce max. matsi masu halatta yayin caji. Dole ne a dauki matakan kariya cikin lokaci.
• Ƙarin firji, wanda zai iya zama dole bayan farawa, ana iya sanya shi cikin sigar tururi a gefen tsotsa.
• Ka guji cika injin da abin firji!
• Kar a yi cajin firijin ruwa a gefen tsotsa akan kwampreso.
• Kada a haxa abubuwan da ake ƙarawa da mai da firji.

Farawa

• Tabbatar cewa duka bawul ɗin rufewa suna buɗe kafin fara kwampreso!
• Bincika cewa aminci da na'urorin kariya (matsi, kariyar mota, matakan kariyar lambar sadarwa, da sauransu) suna aiki da kyau.
• Kunna compressor kuma bari ya yi aiki na akalla minti 10.
• Ya kamata injin ya kai matsayin daidaito.
• Duba matakin mai: Dole ne a ga matakin mai a cikin gilashin gani.
• Bayan an maye gurbin kwampreta, dole ne a sake duba matakin mai. Idan matakin ya yi tsayi da yawa, dole ne a zubar da mai (haɗarin girgiza ruwan mai, rage ƙarfin tsarin firiji).

SANARWA

• Idan an ƙara yawan man mai, akwai haɗarin tasirin mai. Idan haka ne, a duba dawo da mai!

Canjin matsi

• Matsakaicin daidaitawar matsa lamba daidai da UL 207 / EN 378 ko ka'idodin ƙasa waɗanda ke kashe kwampreso kafin a kai matsakaicin matsi mai izini dole ne a shigar a cikin tsarin. Rage matsa lamba don matsa lamba na iya faruwa ko dai a tsotsa da layin matsa lamba tsakanin bawul ɗin kashewa da kwampreso ko kuma a haɗin da ba a kulle ba don bawul ɗin kashewa (haɗin A da B, duba Babi na 9).

Matsi na taimako bawuloli

• An saka compressor tare da bawul ɗin taimako na matsa lamba biyu. Bawul ɗaya kowanne a gefen tsotsa da fitarwa. Idan an kai matsanancin matsin lamba, bawuloli suna buɗewa kuma suna hana ƙarin matsa lamba.
• Game da shi CO2 an busa shi zuwa yanayin yanayi!
• A yayin da bawul ɗin taimako na matsin lamba ya kunna akai-akai, duba bawul ɗin kuma maye gurbin idan ya cancanta saboda lokacin busa matsananciyar yanayi na iya faruwa, wanda zai iya haifar da zubewar dindindin. Koyaushe bincika tsarin don asarar firji bayan kunna bawul ɗin taimako na matsa lamba!
• Bawul ɗin taimako na matsa lamba ba su maye gurbin kowane madaidaicin matsa lamba da ƙarin bawuloli masu aminci a cikin tsarin. Dole ne a shigar da matsi mai matsa lamba koyaushe a cikin tsarin kuma ƙira ko daidaita su daidai da EN 378-2 ko matakan aminci masu dacewa.
• Rashin lura zai iya haifar da haɗarin rauni daga CO2 yawo daga cikin bawul ɗin taimako na matsa lamba biyu!

Gujewa slugging

• Slugging na iya haifar da lalacewa ga kwampreta kuma ya sa firiji ya zube.

Don hana slugging:

• Dole ne a tsara cikakken injin injin da kyau.
• Dole ne a ƙididdige duk abubuwan da aka haɗa tare da juna dangane da fitarwa (musamman magudanar ruwa da bawul ɗin faɗaɗawa).
• Suction gas superheating a shigar da kwampreso ya zama> 15 K (duba saitin na fadada bawul).
• Game da zafin mai da zafin iskar gas. (Zazzabi na iskar gas ya zama babban isa min. 122°F (50°C), don haka zafin mai shine> 86°F (30°C)).
• Dole ne tsarin ya kai matsayin daidaito.
• Musamman ma a cikin tsarin mahimmanci (misali maki da yawa na evaporator), matakan kamar yin amfani da tarkon ruwa, bawul ɗin solenoid a cikin layin ruwa, da sauransu.
• Kada a sami motsi na refrigerant a cikin kwampreso yayin da tsarin ke tsaye.

Tace bushewa

• Gaseous CO2 yana da ƙarancin narkewa a cikin ruwa fiye da sauran firiji. A ƙananan zafin jiki yana iya haifar da toshe bawuloli da tacewa saboda ƙanƙara ko hydrate. A saboda wannan dalili, muna ba da shawarar.
  gyara amfani da isasshiyar bushewar tacewa da gilashin gani tare da alamar danshi.

Kulawa

Shiri

• Kafin fara kowane aiki akan compressor:
• Kashe compressor kuma ka tsare shi don hana sake farawa.
• Rage kwampreso na tsarin matsin lamba.
• Hana iska daga kutsawa cikin tsarin!
• Bayan an yi gyara:
• Haɗa maɓallin aminci.
• Fitar da kwampreso.
• Saki makullin kunnawa.
• Dole ne a aiwatar da lalatawar ta hanyar da ba a samar da busasshiyar ƙanƙara daidai da ƙaƙƙarfan CO2 wanda ke toshe hanyar fita kuma zai iya hana yawo daga CO2. In ba haka ba, akwai haɗarin cewa matsi na iya sake haɓakawa.

Aikin da za a yi

• Don ba da garantin ingantacciyar amincin aiki da rayuwar sabis na kwampreso, muna ba da shawarar aiwatar da aikin sabis da dubawa a tazara na yau da kullun:

Canjin mai:

• ba dole ba ne ga tsarin da masana'anta ke samarwa.
• don shigarwar filin ko lokacin aiki kusa da iyakar aikace-aikacen: a karon farko bayan sa'o'in aiki 100 zuwa 200, sannan kusan. kowace shekara 3 ko 10,000 - 12,000 hours aiki. Zubar da man da aka yi amfani da shi bisa ka'ida; kiyaye dokokin kasa.
• Binciken shekara-shekara: Matsayin mai, ɗigon ruwa, hayaniya mai gudana, matsa lamba, yanayin zafi, aikin na'urori masu taimako kamar na'urar dumama mai, matsa lamba.

Shawarar kayan gyara

• Ana iya samun kayan gyara da na'urorin haɗi akan kayan aikin zaɓin kwampreso a ƙarƙashin vap.bock.de da kuma a bockshop.bock.de.
• Yi amfani da kayan gyara na Bock na gaske!

Man shafawa

• Don aiki tare da CO2 ana buƙatar nau'ikan mai masu zuwa:
• nau'in kwampreso ML da S: BOCKlub E85

Saukewa

• Rufe bawul ɗin kashewa akan kwampreso. CO2 baya buƙatar sake yin fa'ida don haka ana iya busa shi cikin yanayi. Yana da mahimmanci don tabbatar da samun iska mai kyau ko gudanar da CO2 a cikin waje don guje wa haɗarin shaƙewa. Lokacin fitarwa
• CO2, kauce wa raguwa da sauri a cikin matsa lamba don hana mai daga fita da shi. Idan compressor ba a matsawa ba, cire bututun akan matsa lamba- da gefen tsotsa (misali tarwatsa bawul ɗin rufewa, da sauransu) kuma cire kwampreso ta amfani da madaidaicin hoist mai dacewa.
• Zubar da mai a ciki daidai da dokokin kasa da suka dace.
• Lokacin ƙaddamar da kwampreso (misali don sabis ko maye gurbin kwampreso) ana iya saita adadin CO2 mafi girma a cikin mai kyauta. Idan raguwar kwampreso bai isa ba, rufaffiyar bawul ɗin rufewa na iya haifar da matsi mai wuce gona da iri. Don haka dole ne a kiyaye gefen tsotsa (LP) da babban matsi (HP) na kwampreso ta hanyar bawul ɗin lalata.

Bayanan fasaha

1. Haƙuri (± 10%) dangane da ma'anar ƙimar voltage zango. Sauran voltages da nau'ikan halin yanzu akan buƙata.
2. Bayani dalla-dalla ga max. amfani da wutar lantarki ya shafi aikin 60 Hz.
   • Yi lissafin max. aiki halin yanzu / max. amfani da wutar lantarki don ƙirar fuses, layin wadata da na'urorin aminci. Fuse: nau'in amfani da AC3
3. Duk ƙayyadaddun bayanai sun dogara ne akan matsakaita na voltage kewayon
4. Yanke mai haɗin zobe don bututun ƙarfe
5. Don haɗin siyar

Girma da haɗin kai

SV DV	Layin tsotsa duba bayanan fasaha, babi na 8 Layin fitarwa
A	Haɗin tsotsa gefen, ba a kulle ba	1/8 "NPTF
A1	Haɗin tsotsa gefen, mai kullewa	7/16" UNF
B	Gefen fitarwa na haɗi, ba a kulle ba	1/8 "NPTF
B1	Gefen fitarwa na haɗi, mai kullewa	7/16" UNF
D1	Connection mai dawowa daga mai raba mai	1/4 "NPTF
E	Haɗin ma'aunin man fetur	1/8 "NPTF
F	Magudanar mai	M12x1.5
I	Haɗin zafi zafin firikwensin gas	1/8 "NPTF
J	Connection Oil sump hita	3/8 "NPTF
K	Gilashin gani	2 x 1 1/8" - 18 UNEF
L	Haɗin ma'aunin zafi mai zafi	1/8 "NPTF
O	Mai daidaita matakin man fetur	2 x 1 1/8" - 18 UNEF
Q	Haɗin zafin mai	1/8 "NPTF
SI1	Decompression bawul HP	M22x1.5
SI2	Abubuwan da aka bayar na bawul LP	M22x1.5

Sanarwa na haɗawa

• Sanarwa na haɗawa don injunan da ba su cika ba daidai da EC Directive Machinery 2006/42/EC, Annex II 1.B
• Mai ƙira: Boka GmbH
• Benzstrasse 7
• 72636 Frickenhausen, Jamus
• Mu, a matsayin masana'anta, muna bayyana cikin alhakin kawai cewa injin bai cika ba
• Suna: Semi-hermetic kwampreso
• Nau'u: HG(X)12P/60-4 S (HC) ………………………… HG(X)88e/3235-4(S) (HC)
  UL-HGX12P/60 S 0,7……………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ………………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) …………………………. HGX34(P)(e)/380-2 (A)(K)
• HA (X) 12P/60-4 ………………………………………………… (X) 6/1410-4
• HAX22e/125 LT 2 LG ………………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………………. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML (P) 2 CO2T UL-HGX46/440 ML(P) 53 CO2T
• HGZ (X) 7/1620-4 …………………………………. HGZ (X) 7/2110-4
• HGZ (X) 66e/1340 LT 22………………………… HGZ(X)66e/2070 LT 35
• Saukewa: HRX40-2 CO2 TH………………………………. HRX60-2 CO2 TH
• Suna: Buɗe nau'in kwampreso
• Nau'u: F(X)2 …………………………………………………… F(X)88/3235 (NH3)
• FK (X) 1……………………………………………… FK (X) 3
• FK (X) 20/120 (K/N/TK)………………………. FK(X)50/980 (K/N/TK)
• Serial lamba: BC00000A001 - BN99999Z999
• Sanarwa na haɗa kayan aikin da aka kammala daidai da Dokokin Bayar da Kayan Aikin Kaya na Burtaniya 2008, Annex II 1.B
• Mu, a matsayin masana'anta, mun ayyana cikin alhakin kawai cewa injinan da aka kammala a wani bangare
• Suna: Semi-hermetic kwampreso
• Nau'u: HG(X)12P/60-4 S (HC) ………………………… HG(X)88e/3235-4(S) (HC)
• UL-HGX12P/60 S 0,7……………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ………………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) …………………………. HGX34(P)(e)/380-2 (A)(K)
• HA (X) 22e/125-4 ………………………………….. HA (X) 6/1410-4
• HAX22e/125 LT 2 LG ………………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………………. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML(P) 2 CO2T……………………… UL-HGX46/440 ML(P) 53 CO2T
• HGZ (X) 7/1620-4 …………………………………. HGZ (X) 7/2110-4
• HGZ (X) 66e/1340 LT 22………………………… HGZ(X)66e/2070 LT 35
• Saukewa: HRX40-2 CO2 TH………………………………………. HR (Z) X60-2 CO2 T (H) (V)
• Suna: Buɗe nau'in kwampreso
• Nau'u: F(X)2 …………………………………………………………… F(X)88/3235 (NH3)
• FK (X) 1……………………………………………………………………… FK (X) 3
• FK (X) 20/120 (K/N/TK)……………………………….. FK(X)50/980 (K/N/TK)
• Serial lambar: BC00000A001 - BN99999Z999

UL-Takaddar Yardawa

• Ya ku abokin ciniki, Ana iya saukar da Takaddar Yarda da Takaddar QR-Code mai zuwa: https://vap.bock.de/stationaryapplication/Data/
• Takaddun bayanaiFiles/COC CO2 trans.pdf

Kudin hannun jari Danfoss A/S Climate Solutions

• danfoss.us
• +1 888 326 3677
• heat.cs.na@danfoss.com
• Duk wani bayani, gami da, amma ba'a iyakance ga bayanin zaɓi na samfur, aikace-aikacen sa ko amfani da shi ba, ƙirar samfur, nauyi, girma, iya aiki ko duk wani bayanan fasaha a cikin littattafan samfuri, kwatancen kasida, tallace-tallace, da dai sauransu kuma ko an samar da shi a rubuce. , da baki, ta hanyar lantarki, kan layi ko ta hanyar zazzagewa, za a yi la'akari da bayanin, kuma yana ɗaure ne kawai idan kuma har zuwa iyakar, an yi ƙayyadadden bayani a cikin zance ko tabbatarwa. Danfoss ba zai iya karɓar kowane alhakin yuwuwar kurakurai a cikin cataloques, ƙasidu, bidiyo da sauran abubuwa ba. Danfoss yana da haƙƙin canza kayan sa ba tare da sanarwa ba. Wannan kuma ya shafi samfuran da aka ba da oda amma ba a isar da su ba muddin ana iya yin irin waɗannan sauye-sauye ba tare da canje-canje don ƙira, dacewa ko aikin samfurin ba.
• Duk alamun kasuwanci a cikin wannan kayan mallakar Danfoss A/S ne ko kamfanonin rukunin Danfoss. Danfoss da tambarin Danfoss alamun kasuwanci ne na Danfoss A/S. An kiyaye duk haƙƙoƙi.

Takardu / Albarkatu

Danfoss BOCK UL-HGX12e CO2 LT Maimaita Kwamfuta [pdf] Jagoran Shigarwa BOCK UL-HGX12e CO2 LT Maimaita Kwamfuta, BOCK UL-HGX12e CO2 LT, Maimaitawa Kwamfuta, Compressor

Magana

• Manual mai amfani