ENGO Inodzora EFAN-24 PWM Fan Speed Control
Zvinotsanangurwa
- Protocol: MODBUS RTU
- Mutevedzeri weMutongi: EFAN-24
- Kukurukurirana Interface: RS485
- Kero Range: 1-247
- Data Saizi: 32-bit
Mirayiridzo Yekushandiswa Kwechigadzirwa
- Kugadziriswa kweEFAN-24 controller kunofanirwa kuitwa nemunhu ane ruzivo ane mvumo yakakodzera uye ruzivo rwehunyanzvi, achitevera nyika uye EU zviyero nemirairo.
- Kutadza kutevedzera mirairo kunogona kukanganisa basa remugadziri.
- Iye controller anogona kushanda semuranda mune yeMODBUS RTU network ine chaiwo maficha uye kutaurirana zvinodiwa. Iva nechokwadi chekugadzirisa wiring kuitira kudzivirira huwori hwe data.
- Network Connection: RS-485 serial interface
- Kurongeka kweData: Kero, kumhanya, uye fomati zvinotemwa nehardware
- Kuwana Data: Kuwana kuzere kune controller's ladder chirongwa data
- Saizi yedata: 2 mabytes paMODBUS data register
- Usati wabatanidza mutongi kune RS-485 network, ita shuwa kurongeka kwakaringana kwezvirongwa zvekutaurirana, kusanganisira kero, baud rate, parity, uye kumira mabhiti.
- Unconfigured controllers haafaniri kubatanidzwa kune network kudzivirira nyaya dzekushanda.
General information
Ruzivo rwakakwana nezve MODBUS RTU
Iyo MODBUS RTU chimiro inoshandisa master-muranda system kuchinjanisa mameseji. Inobvumira huwandu hwevaranda mazana maviri nemakumi mana nevanomwe, asi tenzi mumwe chete. Tenzi anodzora kushanda kwetiweki, uye chete ndiyo inotumira chikumbiro. Varanda havaite transmissions vari voga. Kukurukurirana kwega kwega kunotanga natenzi achikumbira Muranda, uyo anopindura tenzi nezvaanenge abvunzwa. Tenzi (kombiyuta) anotaurirana nevaranda (vatongi) mune mbiri-waya RS-485 mode. Izvi zvinoshandisa data mitsara A+ uye B- yekuchinjana data, iyo INOFANIRA kuva imwe yakamonyoroka peya.
Hapana anopfuura waya maviri anogona kubatanidzwa kune imwe neimwe terminal, kuve nechokwadi chekuti "Daisy Chain" (mukutevedzana) kana "yakatwasuka mutsara" (yakananga) gadziriso inoshandiswa. Nyeredzi kana network (yakavhurika) yekubatanidza haina kukurudzirwa, sezvo kuratidza mukati metambo kunogona kukonzera huwori hwe data.
Configuration
- Kugadzirisa kunofanirwa kuitwa nemunhu ane hunyanzvi ane mvumo yakakodzera uye ruzivo rwehunyanzvi, achitevera zviyero nemirairo yenyika uye EU.
- Mugadziri haazove nemhosva kune chero maitiro asina kutevedzera mirairo.
TARIRA:
Panogona kunge paine zvimwe zvekudzivirira zvinodiwa pakumisikidzwa nekumisikidzwa kwese, izvo mugadziri/mugadziri ane basa rekuchengetedza.
MODBUS RTU network kushanda - Slave mode
Engo's MODBUS controller ine zvinotevera maficha kana uchishanda semuranda mune MODBUS RTU network:
- Network yekubatanidza kuburikidza neRS-485 serial interface.
- Kero, kumhanya kwekutaurirana, uye byte fomati inotemwa nehardware kumisikidzwa.
- Inobvumira kupinda kune vese tags uye data rinoshandiswa mucontroller's ladder program.
- 8-bit kero yemuranda
- 32-bit data saizi (1 kero = 32-bit data kudzoka)
- Imwe neimwe yeMODBUS data rerejista ine saizi ye2 bytes.
TARIRA:
- Mutongi asati abatanidzwa kune RS-485 network, inofanira kutanga yakanyatsogadziriswa.
- Zvirongwa zvekutaurirana zvinogadziriswa muzvikamu zvebasa remutongi (mudziyo).
TARIRA:
- Kubatanidza unconfigured controllers kune RS-485 network inoguma nekushanda kusina kunaka.
- Copyright - Gwaro iri rinogona kungogadzirwazve uye kugovaniswa nemvumo yeEngo Controls uye rinogona kupihwa kune vanhu vane mvumo kana makambani ane hunyanzvi hwehunyanzvi hunodiwa.
zvirongwa zvekutaurirana
RS-485 kutaurirana marongero
| Pxx | Function | Value | Tsanangudzo | Default value |
| Wedzera | MODBUS Slave mudziyo kero (ID). | 1-247 | MODBUS Slave mudziyo kero (ID). | 1 |
|
BAUD |
Baud |
4800 |
Bitrate (Baud) |
9600 |
| 9600 | ||||
| 19200 | ||||
| 38400 | ||||
|
PARI |
Parity bit - inoseta data parity yekuona kukanganisa |
Hapana | Hapana |
Hapana |
| Kunyange | Kunyange | |||
| Odd | Odd | |||
| MIRA | StopBit | 1 | 1 mira zvishoma | 1 |
| 2 | 2 mira zvishoma |
Inotsigira makodhi emabasa anotevera:
- 03 - kuverenga n marejista (Kubata Marejista)
- 04 - kuverenga n marejista (Input Registers)
- 06 - Nyora 1 rejista (Kubata Rejista)
INPUT marejista - kuverenga chete
| Adress | Access | Tsanangudzo | Value range | Means | Default | |
| Dec | Hex | |||||
| 0 | 0x0000 | R (#03) | Engo MODBUS Model ID | 1-247 | MODBUS Muranda (ID) | 1 |
| 1 | 0x0001 | R (#03) | Firmware-Version | 0x0001-0x9999 | 0x1110=1.1.10 (BCD kodhi) | |
|
2 |
0x0002 |
R (#03) |
Kushanda-nyika |
0b00000010=Kushaya basa, DZIMA 0b00000000=Kusashanda, tembiricha yekamuri 0b10000001=Kudziya 0b10001000=Kutonhora
0b00001000 = Kusina basa, sensor kukanganisa |
||
| 3 | 0x0003 | R (#03) | Kukosha kweIntegrated tembiricha sensor, °C | 50-500 | N-> temp=N/10 °C | |
|
5 |
0x0005 |
R (#03) |
Kukosha kwekunze tembiricha sensor S1, °C |
50-500 |
0 = Vhura (sensor break)/ contact yakazaruka
1 =Yakavharwa (sensor short circuit)/ contact yakavharwa N-> temp=N/10 °C |
|
|
6 |
0x0006 |
R (#03) |
Kukosha kwekunze tembiricha sensor S2, °C |
50-500 |
0 = Vhura (sensor break)/ contact yakazaruka
1 =Yakavharwa (sensor short circuit)/ contact yakavharwa N-> temp=N/10 °C |
|
|
7 |
0x0007 |
R (#03) |
Fan state |
0b00000000 - 0b00001111 |
0b00000000= KUBVA
0b00000001= Ini Fan stage low 0b00000010= II Fan stage zvepakati 0b00000100= III Fan state yakakwirira 0b00001000= Auto - DZIMA 0b00001001= Auto - I low 0b00001010= Auto - II yepakati 0b00001100= Auto - III yakakwirira |
|
| 8 | 0x0008 | R (#03) | Valve 1 nhamba | 0-1000 | 0 = KUDZIMA (vhavha yakavharwa)
1000 = ON / 100% (vhavha yakazaruka) |
|
| 9 | 0x0009 | R (#03) | Valve 2 nyika | 0-1000 | 0 = KUDZIMA (vhavha yakavharwa)
1000 = ON / 100% (vhavha yakazaruka) |
|
| 10 | 0x000A | R (#03) | Humidity kuyerwa (ine 5% inoratidza chokwadi) | 0-100 | N-> humidity=N % | |
KUBATA marejista - ekuverenga nekunyora
| Adress | Access | Tsanangudzo | Value range | Means | Default | |
| Dec | Hex | |||||
| 0 | 0x0000 | R/W (#04) | Engo MODBUS Model ID | 1-247 | MODBUS Muranda (ID) | 1 |
|
234 |
0x00EA |
R/W (#06) |
Fancoil mhando |
1-6 |
1 = 2 pombi - chete kupisa 2 = 2 pombi - chete kutonhora
3 = 2 pombi – kudziyisa nekutonhodza 6 = 4 pombi - kupisa kwepasi uye kutonhora nefancoil |
0 |
|
235 |
0x00EB |
R/W (#06) |
S1-COM yekuisa gadziriso (Installer Parameters -P01) |
0 | Input isingashande. Shandura pakati pekudziya nekutonhodza nemabhatani. |
0 |
|
1 |
Input inoshandiswa kushandura kupisa / kutonhora kuburikidza nekunze kubata kwakabatana neS1-COM:
- S1-COM yakavhurika -> HEAT maitiro - S1-COM yakapfupika -> COOL modhi |
|||||
|
2 |
Kupinza kunoshandiswa KUCHINJA kudziya/kutonhodza zvichibva paPIPE TEMPERATURE mu 2-pipe system.
Mutongi anoshandura pakati pekupisa uye kutonhora modes zvichienderana nepombi tembiricha yakaiswa mu parameters P17 uye P18. |
|||||
|
3 |
Bvumira feni kushanda zvinoenderana nekuyerwa kwekushisa papombi. For example, kana kutonhora kwepombi kwakanyanyisa, uye mutongi ari mukupisa mode
- Iyo pombi sensor haibvumire fan kuti imhanye. Shanduko yekudziya / kutonhora kunoitwa nemaoko, uchishandisa mabhatani. Hukoshi hwekutonga kwe fan hunoenderana nekupisa kwepombi dzakaiswa mumaparamita P17 uye P18. |
|||||
| 4 | Kuitwa kweiyo sensor yepasi mukati mekugadzirisa kupisa kwepasi. | |||||
|
236 |
0x00EC |
R/W (#06) |
S2-COM yekuisa gadziriso (Installer Parameters -P02) |
0 | Input yadzimwa |
0 |
| 1 | Occupancy sensor (kana mameseji akavhurwa, activate ECO mode) | |||||
| 2 | External tembiricha sensor | |||||
|
237 |
0x00ED |
R/W (#06) |
Inosarudzwa ECO modhi (Installer Parameters -P07) | 0 | HAPANA - Akaremara |
0 |
| 1 | HONGU - Active | |||||
| 238 | 0x00EE | R/W (#06) | ECO mode tembiricha kukosha kwekudziya (Installer parameters -P08) | 50-450 | N-> temp=N/10 °C | 150 |
| 239 | 0x00EF | R/W (#06) | ECO mode tembiricha kukosha kwekutonhora (Installer paramita -P09) | 50-450 | N-> temp=N/10 °C | 300 |
|
240 |
0x00F0 |
R/W (#06) |
ΔT ye0- 10V kushanda kwevharuvhu
Iyi parameter inokonzera iyo modulated 0- 10V kubuda kwevhavha. -Mukupisa modhi: Kana tembiricha yekamuri yadonha, vharuvhu inovhura zvakaenzana kune delta saizi. -Mukutonhora modhi: Kana tembiricha yekamuri ikawedzera, vharafu inovhura inoenderana nehukuru ye delta. Kuvhura kwevharuvhu kunotanga kubva kune tembiricha yekamuri. (Yekuisira paramita -P17) |
1-20 |
N-> temp=N/10 °C |
10 |
|
241 |
0x00F1 |
R/W (#06) |
Fani pane tembiricha yekudziya
Iyo fan ichatanga kushanda kana tembiricha yemukamuri inodonha pazasi pe preset nekukosha kweparameter (Installer parameters -P15) |
0-50 |
N-> temp=N/10 °C |
50 |
| Adress | Access | Tsanangudzo | Value range | Means | Default | |||
| Dec | Hex | |||||||
|
242 |
0x00F2 |
R/W (#06) |
Kudzora algorithm
(TPI kana hysteresis) yevhavha yekupisa (Installer parameters -P18) |
0-20 |
0 = TPI
1 = ±0,1C 2 = ±0,2C... N-> temp=N/10 °C (±0,1…±2C) |
5 |
||
|
243 |
0x00F3 |
R/W (#06) |
FAN delta algorithm yekutonhodza
Iyo parameter inosarudza hupamhi hwetembiricha renji umo fan inoshanda mukutonhora mode. Kana tembiricha yekamuri ikawedzera, zvino: 1. Kana kukosha kudiki kweDelta FAN, kukurumidza kupindura kwe fan kune shanduko yekushisa tembiricha - nekukurumidza kuwedzera kwekukurumidza.
2. Kana kukosha kukuru kweDelta FAN, fan inononoka inowedzera kukurumidza. (Midziyo yekuisa -P16) |
5-50 |
N-> temp=N/10 °C |
20 |
||
|
244 |
0x00F4 |
R/W (#06) |
Fani patembiricha yekutonhodza.
Iyo fan ichatanga kushanda kana tembiricha yemumba ichikwira pamusoro pe setpoint nekukosha kweparameter. (Midziyo yekuisa -P19) |
0-50 |
N-> temp=N/10 °C |
50 |
||
| 245 | 0x00F5 | R/W (#06) | Hysteresis kukosha kwevhavha inotonhora (Installer parameters -P20) | 1-20 | N-> temp=N/10 °C (±0,1…±2C) | 5 | ||
|
246 |
0x00F6 |
R/W (#06) |
Nzvimbo yakafa yekuchinja kupisa / kutonhora
Mune 4-pipe system. Musiyano pakati peSet tembiricha uye tembiricha yekamuri, pane iyo controller inozochinja otomatiki yekudziya / kutonhora kushanda mode. (Midziyo yekuisa -P21) |
5-50 |
N-> temp=N/10 °C |
20 |
||
|
247 |
0x00F7 |
R/W (#06) |
Kuchinja kwetembiricha kukosha kubva pakudziya kuenda kunotonhodza
- 2-pombi system. Mune 2-pipe system, pazasi kukosha uku, sisitimu inochinja kune inotonhorera mode uye inobvumira fan kuti itange. (Midziyo yekuisa -P22) |
270-400 |
N-> temp=N/10 °C |
300 |
||
|
248 |
0x00F8 |
R/W (#06) |
Kukosha kwekushisa kwekuchinja kubva pakutonhora kusvika pakupisa, 2-pipe system.
Mune 2-pipe system, pamusoro pekukosha uku, sisitimu inochinja kune yekudziya mode uye inobvumira fan kuti itange. (Midziyo yekuisa -P23) |
100-250 |
N-> temp=N/10 °C |
100 |
||
|
249 |
0x00F9 |
R/W (#06) |
Kutonhodza PAKUnonoka.
Iyo parameter inoshandiswa mune 4-pombi masisitimu ane otomatiki switching pakati pekudziya uye kutonhora. Izvi zvinodzivirira kazhinji kuchinjika pakati pekudziya uye kutonhora modhi uye oscillation yekushisa kwekamuri. (Midziyo yekuisa -P24) |
0 - 15 min |
0 |
|||
|
250 |
0x00FA |
R/W (#06) |
Maximum pasi tembiricha
Kuti udzivirire pasi, kupisa kuchadzimwa kana tembiricha yepasi sensor ichikwira pamusoro pekukosha kwepamusoro. (Midziyo yekuisa -P25) |
50-450 |
N-> temp=N/10 °C |
350 |
||
|
251 |
0x00FB |
R/W (#06) |
Minimum floor tembiricha
Kuti udzivirire pasi, kupisa kuchashandurwa, kana tembiricha yepasi sensor inodonha pasi pemutengo wepasi. (Midziyo yekuisa -P26) |
50-450 |
N-> temp=N/10 °C |
150 |
||
| 254 | 0x00FE | R/W (#06) | PIN kodhi yekuisa zvigadziriso (Installer Parameters -P28) | 0-1 | 0 = yakaremara
1 = PIN (Chekutanga default kodhi 0000) |
0 | ||
| Adress | Access | Tsanangudzo | Value range | Means | Default | |
| Dec | Hex | |||||
| 255 | 0x00FF | R/W (#06) | Inoda PIN kodhi kuvhura makiyi (Installer Parameters -P29) | 0-1 | 0 = NE
1 = TAK |
0 |
|
256 |
0x0100 |
R/W (#06) |
Kushanda kweFan (Installer parameters -FAN) |
0-1 |
0 = HAPANA - Isingashande - inobuda maitirwo ekudzora fan akaremara zvachose
1 = HONGU |
1 |
| 257 | 0x0101 | R/W (#06) | Simba pa / kudzima - kudzima regulator | 0,1 | 0 = YAKADZWA
1 = ON |
1 |
|
258 |
0x0102 |
R/W (#06) |
Operation mode |
0,1,3 |
0=Chinyorwa 1=Kuronga
3=FROST - anti-freeze mode |
0 |
|
260 |
0x0104 |
R/W (#06) |
Fani yekumhanyisa kuseta |
0b000000= KUDZIMIRA – fan off 0b00000001= I (yakaderera) fan gear 0b000010= II (pakati) fan gear 0b00000100= III (yakakwirira) fan gear
0b00001000= Otomatiki feni kumhanya - OFF 0b00001001= Otomatiki feni kumhanya - 1st giya 0b00001010= Otomatiki feni kumhanya - yechipiri giya 0b00001100= Otomatiki feni kumhanya - rechitatu giya |
||
| 262 | 0x0106 | R/W (#06) | Kiyi kiyi | 0,1 | 0=kuvhurwa 1=Yakakiiwa | 0 |
| 263 | 0x0107 | R/W (#06) | Ratidza kupenya (Installer Parameters -P27) | 0-100 | N-> Kupenya =N% | 30 |
| 268 | 0x010C | R/W (#06) | Wachi - maminitsi | 0-59 | Maminitsi | 0 |
| 269 | 0x010D | R/W (#06) | Wachi - maawa | 0-23 | Maawa | 0 |
| 270 | 0x010E | R/W (#06) | Wachi - Zuva revhiki (1= Muvhuro) | 1~7 | Zuva revhiki | 3 |
| 273 | 0x0111 | R/W (#06) | Isa tembiricha muhurongwa hwekuita | 50-450 | N-> temp=N/10 °C | 210 |
| 274 | 0x0112 | R/W (#06) | Seta tembiricha mune manual mode | 50-450 | N-> temp=N/10 °C | 210 |
| 275 | 0x0113 | R/W (#06) | Isa tembiricha muFROST mode | 50 | N-> temp=N/10 °C | 50 |
| 279 | 0x0117 | R/W (#06) | Kunonyanyisa setpoint tembiricha | 50-450 | N-> temp=N/10 °C | 350 |
| 280 | 0x0118 | R/W (#06) | Minimum setpoint tembiricha | 50-450 | N-> temp=N/10 °C | 50 |
| 284 | 0x011C | R/W (#06) | Kururama kwekushisa kwakaratidzwa | 1, 5 | N-> temp=N/10 °C | 1 |
| 285 | 0x011D | R/W (#06) | Kugadziriswa kwekushisa kwakaratidzwa | -3.0… 3.0°C | mumatanho e0.5 | 0 |
| 288 | 0x0120 | R/W (#06) | Sarudzo yerudzi rwesystem - kudziyisa / kutonhora (zvinoenderana nekumisikidzwa kwekuisa S1) | 0,1 | 0 = Kupisa
1 = Kutonhodza |
0 |
| 291 | 0x0123 | R/W (#06) | Minimum fan kumhanya (Installer Parameters-P10) | 0-100 | N-> speed=N % | 10 |
| 292 | 0x0124 | R/W (#06) | Maximum fan kumhanya (Installer Parameters-P11) | 0-100 | N-> speed=N % | 90 |
| 293 | 0x0125 | R/W (#06) | Kumhanya kwefan 1st giya mune yemanyorero modhi (Installer paramita-P12) | 0-100 | N-> speed=N % | 30 |
| 294 | 0x0126 | R/W (#06) | Kumhanya kwefan 2nd giya mune yemanyorero modhi (Installer paramita-P13) | 0-100 | N-> speed=N % | 60 |
| 295 | 0x0127 | R/W (#06) | Kumhanya kwe fan 3rd giya mune yemanyorero modhi (Installer paramita-P14) | 0-100 | N-> speed=N % | 90 |
FAQ
- Q: Ndeapi magadzirirwo ekutaurirana akasarudzika eEFAN-24 controller?
- A: Izvo zvigadziriso zvinosanganisa kero yemuranda ye1, iyo baud mwero we9600, hapana parity bit, uye imwe kumira zvishoma.
- Q: Ndingawana sei marejista akasiyana e data muMODBUS RTU network?
- A: Shandisa macode ebasa akakodzera akadai #03 ekuverenga akabata marejista kana #06 yekunyora rejista imwechete. Rejista yega yega ine chaiyo data data ine chekuita necontroller parameters.
Zvinyorwa / Zvishandiso
 |
ENGO Inodzora EFAN-24 PWM Fan Speed Control [pdf] Bhuku reMirayiridzo EFAN-230B, EFAN-230W, EFAN-24 PWM Fan Speed Controller, EFAN-24, PWM Fan Speed Controller, Fan Speed Controller, Speed Controller |