I-LECTROSONICS DBSM-A1B1 iTranskoda yeDijithali

Ulwazi lweMveliso

• Umzekelo: DBSM/DBSMD Digital Transcorder
• Uluhlu lokuphindaphinda: 470.100 ukuya 607.950 MHz (DBSM/DBSMD/E01 frequency uluhlu 470.100 ukuba 614.375 MHz)
• Amandla emveliso: Okukhethiweyo 10, 25, okanye 50 mW
• Imo yoThutho: Imowudi yoxinano oluphezulu kwi-2 mW
• Umthombo wamandla: Iibhetri ezimbini ze-AA
• Igalelo likaJack: I-Lectrosonics eqhelekileyo ye-5-pin yokufaka i-jack
• I-Antenna Port: 50 ohm SMA isinxibelelanisi

Imiyalelo yokusetyenziswa kwemveliso

• Ngaphezuluview
  I-DBSM/DBSMD transmitter yenzelwe ukusebenza kakuhle kunye nexesha elongeziweyo lokusebenza. Isebenza kuyo yonke ibhendi kamabonwakude ye-UHF ngokhetho olukhethiweyo lwamandla aphumayo.
• Ukuvula amandla
  Faka iibhetri ezimbini ze-AA kwi-transmitter. Qinisekisa ukuba iibhetri zifakwe ngokufanelekileyo kunye ne-polarity echanekileyo. Cinezela iqhosha lamandla ukuvula i-transmitter.
• UkuTyunwa rhoqo
  Sebenzisa ulawulo lokulungisa ukukhetha amaza omoya afunekayo phakathi koluhlu oluxhaswayo. Qinisekisa ukuba i-frequency transmitter ihambelana ne-frequency ye-receiver yonxibelelwano olufanelekileyo.
• Input Connection
  Qhagamshela i-microphone yakho okanye umthombo we-audio kwi-Lectrosonics eqhelekileyo ye-5-pin yokufaka i-jack kwi-transmitter. Sebenzisa iintambo ezifanelekileyo kunye nezihlanganisi zoqhagamshelwano olukhuselekileyo.
• Izicwangciso zeNqanaba
  Lungisa amanqanaba eaudio usebenzisa i-keypad ii-LED zeseto ezikhawulezayo nezichanekileyo. Beka iliso kumanqanaba ukunqanda ukugqwetheka okanye ukusika iaudio.
• Umsebenzi wokurekhoda
  I-transmitter inomsebenzi wokurekhoda eyakhelwe-ngaphakathi wokusetyenziswa ngokuzimeleyo okanye iimeko apho ukuhanjiswa kweRF kungenakwenzeka. Khumbula ukuba ukurekhodwa kunye nokuhambisa akunakwenziwa ngaxeshanye.
• Ukutshintshwa kwebhetri
  Jonga imeko yebhetri rhoqo. Xa iibhetri zisezantsi, zibuyisele iibhetri ezintsha ze-AA ukuqinisekisa ukusebenza okungaphazanyiswa.

Imibuzo ebuzwa qho

Umbuzo: Ngaba ndingasebenzisa iimakrofoni ezingezizo zeLectrosonics kunye ne-transmitter?

A: Ewe, unokuphelisa ii-microphone ezingezizo zeLectrosonics usebenzisa ukupheliswa kwentambo ezifanelekileyo. Jonga kwincwadi yomsebenzisi ngemiyalelo eneenkcukacha malunga nolungelelwaniso lweingcingo.

Q: Yintoni injongo yoMda weInput olawulwa yiDSP?

A: I-Input Limit elawulwa yi-DSP inceda ukuthintela ukuphazamiseka komsindo ngokunciphisa amanqanaba egalelo ngaphakathi koluhlu olukhuselekileyo, ukuqinisekisa ukuhanjiswa okucacileyo komsindo.

Q: Ndazi njani ukuba kufuneka ndibuyisele iibhetri?

A: Gcina iliso kwisalathisi sesimo sebhetri. Xa isalathisi sibonisa amanqanaba ebhetri aphantsi, buyisela iibhetri ngokukhawuleza ukuphepha ukuphazamiseka ekusebenzeni.

Intshayelelo

I-DBSM/DBSMD transmitter isebenzisa i-high-efficiency digital circuitry ukwenzela ixesha elide lokusebenza kwiibhetri ezimbini ze-AA. Umthumeli unokuvula amanyathelo kwibhendi kamabonwakude ye-UHF ukusuka kwi-470.100 ukuya kwi-607.950 MHz
(I-DBSM/DBSMD/E01 i-frequency range yi-470.100 ukuya kwi-614.375 MHz), enegunya elikhethiweyo lokuphuma kwe-10, i-25, okanye i-50 mW. Imowudi yosulelo olunoxinaniso oluphezulu kwi-2 mW ivumela isithuba somthwali osondeleyo kumatshaneli aphezulu ngaphakathi kwesixa esinikiweyo se-spectrum.

I-architecture ecocekileyo yedijithali yenza ukuba i-AES 256 iguqulelwe kwi-encryption kwizicelo zokhuseleko eziphezulu. Umgangatho wokusebenza kweaudio yeStudio uqinisekiswa zizinto ezikumgangatho ophezulu ngaphambiliamp, ulungelelwaniso olubanzi lokuzuza igalelo, kunye nokunciphisa okulawulwa yi-DSP. Uqhagamshelwano lwee-input kunye nezicwangciso zibandakanyiwe kuyo nayiphi na i-microphone ye-Lavaliere, ii-microphone eziguquguqukayo, kunye nokufakwa kwinqanaba lomgca. Ingeniso yokufaka i-adjustable phezu koluhlu lwe-44 dB kumanyathelo e-1 dB ukuvumela umdlalo ochanekileyo kumgangatho wesignali yegalelo, ukwandisa uluhlu oluguquguqukayo kunye ne-signal-to-noise ratio.

Indlu yipakethe ye-aluminium enqabileyo, eyenziwe ngomatshini kunye ne-Lectrosonics ye-5-pin yokufaka i-jack ukuze isetyenziswe kunye ne-electret lavaliere mics, i-mics eguqukayo, i-pickup yesixhobo somculo, kunye neempawu zomgangatho womgca. Ii-LED ezikwiphedi zivumela useto olukhawulezayo noluchanekileyo lwenqanaba ngaphandle kokufuneka view umamkeli. Iyunithi inikwe amandla yi-AA ibhetri-ies, kwaye i-antenna port isebenzisa i-standard 50 ohm SMA isixhumi.
Ukutshintsha izixhobo zombane zibonelela ngevolthi rhoqotages kwiisekethe zothumelo ukusuka ekuqaleni ukuya ekupheleni kobomi bebhetri, kunye namandla aphumayo ahlala engaguquki kubomi bebhetri.

i-Servo Bias Input kunye ne-Wiring
Ungeniso lwangaphambiliamp luyilo olulodwa oluzisa uphuculo oluvakalayo ngaphezu kwamagalelo aqhelekileyo okuhambisa. Iiplani ezimbini ezahlukeneyo ze-microphone wiring schemes ziyafumaneka ukwenza lula kunye nokulungelelanisa uqwalaselo. Ulungelelwaniso olulula lwe-2-cingo kunye nocingo olu-3 lubonelela ngamalungiselelo aliqela enzelwe ukusetyenziswa kuphela ngamagalelo e-servo bias ukuthatha i-advan epheleleyo.tage ngaphambiliamp ukujikeleza. I-wiring ye-input ye-line-level inika impendulo ye-frequency eyandisiweyo kunye ne-LF roll-off kwi-20 Hz yokusetyenziswa kunye nezixhobo kunye nemithombo yesignali yomgca.

I-Input Limiter elawulwa yi-DSP
Umthumeli usebenzisa isithinteli somsindo we-analog elawulwa ngokwedijithali phambi kwe-analog-to-digital converter. I-limiter inoluhlu olungaphezulu kwe-30 dB yokukhusela okugqithisiweyo okugqwesileyo. Imvulophu ekhutshwa kabini yenza isithinteli sibonakale ngokucacileyo ngelixa sigcina ukugqwetheka okuphantsi. Inokucingwa ngokuba yimida emibini kuthotho, idityaniswe njengohlaselo olukhawulezayo kunye nokukhulula umda olandelwa kuhlaselo olucothayo kunye nokukhulula umda. I-limiter iphinda ibuyele ngokukhawuleza kwizinto ezidlulayo ezimfutshane, ukuze isenzo sayo sifihlwe kumphulaphuli, kodwa sibuyela ngokukhawuleza kumanqanaba aphakamileyo azinzileyo ukuze kugcinwe ukuphazamiseka kweaudio kuphantsi kunye nokugcina utshintsho oluguqukayo lwexesha elifutshane kwi-audio.

Umsebenzi wokurekhoda
I-DBSM/DBSMD inomsebenzi wokurekhoda eyakhelwe-ngaphakathi wokusetyenziswa kwiimeko apho iRF ingenakwenzeka okanye isebenze njengerekhodi yodwa. Umsebenzi werekhodi kunye nokuhanjiswa kwemisebenzi kukodwa omnye komnye - awukwazi ukurekhoda KWAYE nokuhambisa ngaxeshanye. Xa iyunithi ithumela kwaye irekhoda ivuliwe, i-audio kwi-RF transmission iya kuyeka, kodwa isimo sebhetri siya kuthunyelwa kumamkeli. Umshicileli sampngaphantsi kwireyithi ye-48 kHz ene-24-bit sample ubunzulu. Ikhadi le-SDHC elincinci libonelela ngezakhono ezilula zokuhlaziya i-firmware ngaphandle kwesidingo sentambo ye-USB okanye imiba yomqhubi.

Uguqulelo oluntsonkothileyo
Xa usasaza iaudio, kukho iimeko apho ubumfihlo buyimfuneko, njengakwiminyhadala yemidlalo yobuchwephesha, kumagumbi enkundla okanye kwiintlanganiso zabucala. Kwiimeko apho ukuhanjiswa kweaudio yakho kufuneka kugcinwe kukhuselekile, ngaphandle kokuncama umgangatho weaudio, iLectrosonics isebenzisa ufihlo lwe-AES256 kwiinkqubo zethu zedijithali ezingenazingcingo. Izitshixo eziphezulu ze-entropy encryption zenziwa kuqala ngumamkeli we-Lectrosonics njenge-DSQD Receiver. Isitshixo emva koko sidityaniswa ne-DBSM nge-IR port. Uthumelo luya kuguqulelwa ngokuntsonkothileyo kwaye lunokukhutshwa kuphela ukuba umamkeli kunye nomthumeli banamaqhosha oguqulelo ahambelanayo. Ukuba uzama ukuhambisa isignali yesandi kwaye izitshixo azihambelani, konke okuya kuviwa kukuthula.

Ukuhambelana nememori khadi ye-microSDHC

• Nceda uqaphele ukuba i-DBSM/DBSMD yenzelwe ukusetyenziswa kunye namakhadi ememori ye-microSDHC. Kukho iintlobo ezininzi zemigangatho yekhadi le-SD (njengoko kolu kubhalwa) ngokusekelwe kumthamo (ukugcinwa kwi-GB).
  • I-SDSC: umthamo osemgangathweni, ukuya kuthi ga kunye nokubandakanya i-2 GB - UNGASEBENZISI!
  • I-SDHC: umthamo ophezulu, ngaphezu kwe-2 GB kwaye ukuya kuthi ga kunye nokuquka i-32 GB - SEBENZISA OLU HLOBO.
  • I-SDXC: umthamo owandisiweyo, ngaphezulu kwe-32 GB kwaye ukuya kuthi ga kunye nokubandakanya i-2 TB - UNGASEBENZISI!
  • I-SDUC: umthamo owandisiweyo, ngaphezulu kwe-2TB kwaye ukuya kuthi ga kunye nokuquka i-128 TB – UNGASEBENZISI!
• Amakhadi amakhulu e-XC kunye ne-UC asebenzisa indlela eyahlukileyo yokufomatha kunye nesakhiwo sebhasi kwaye AKUKHO ukuhambelana nomshicileli. Ezi ziqhele ukusetyenziswa kunye neenkqubo zevidiyo zesizukulwana esilandelayo kunye neekhamera zezicelo zemifanekiso (ividiyo kunye nesisombululo esiphezulu, ukufota ngesantya esiphezulu).
• KUPHELA imemori khadi ye-microSDHC ekufuneka isetyenziswe. Zifumaneka ngamandla ukusuka kwi-4GB ukuya kwi-32 GB. Khangela i-Speed ​​Class Class Class 10 amakhadi (njengoko kuboniswe yi-C ehlanganiswe nenombolo ye-10), okanye i-UHS Speed ​​Class Class Class Ikhadi (njengoko kuboniswe ngenombolo ye-1 ngaphakathi kwesimboli se-U). Kwakhona, qaphela ilogo ye-microSDHC.
• Ukuba utshintshela kuhlobo olutsha okanye umthombo wekhadi, sihlala sicebisa uvavanyo kuqala ngaphambi kokusebenzisa ikhadi kwisicelo esibalulekileyo.
• Olu phawu lulandelayo luya kuvela kwiimemori khadi ezihambelanayo. Enye okanye zonke iimpawu ziya kubonakala kwizindlu zekhadi kunye nokupakishwa.

Iimbonakalo

Izalathi zefestile ezingundoqo
IWindow engundoqo ibonisa imowudi yeRF okanye yokuSebenza (yokuhambisa), amaza okusebenza, inqanaba lesandi, kunye nemo yebhetri.

Ubume bebhetri isalathisi LED

• Iibhetri zeAA zingasetyenziselwa ukunika amandla isidluliseli.
• I-LED ebhalwe BATT kwiphedi yamaqhosha ikhanya luhlaza xa iibhetri zilungile. Umbala utshintsha ubebomvu xa ibhetri inamandlatagi-e yehla kwaye ihlala ibomvu kwintsalela yobomi bebhetri. Xa i-LED iqala ukuqhwanyaza bomvu, kuya kuba yimizuzu embalwa nje yexesha eliseleyo.
• Eyona ndawo apho ii-LED zijika zibebomvu ziyakwahluka ngohlobo lwebhetri kunye nemeko, ubushushu, kunye nokusetyenziswa kwamandla. Ii-LED zenzelwe ukubamba nje ingqalelo yakho, ingabi ngumqondiso ochanekileyo wexesha eliseleyo.
• Ibhetri ebuthathaka ngamanye amaxesha iya kubangela ukuba i-LED ikhazimle luhlaza kwangoko emva kokuba i-transmitter ivuliwe, kodwa iya kukhupha ngokukhawuleza ukuya kwindawo apho i-LED iya kuba bomvu okanye iyunithi iya kucima ngokupheleleyo.
• Ezinye iibhetri zinika isilumkiso esincinane okanye aziniki silumkiso xa ziphelelwe. Ukuba unqwenela ukusebenzisa ezi bhetri kwi-transmitter, kuya kufuneka ukuba uligcine ngesandla ixesha lokusebenza usebenzisa isibali-xesha sebhetri esamkelayo ukuthintela ukuphazamiseka okubangelwa ziibhetri ezifileyo.
• Qala ngebhetri egcweleyo, emva koko ulinganise ixesha elithathwayo ukuze i-Power LED iphume ngokupheleleyo.

PHAWULA:
Uphawu lwesibali-xesha sebhetri kuninzi lwabamkeli beLectrosonics luluncedo kakhulu ekulinganiseni ixesha lebhetri. Jonga kwimiyalelo yomamkeli ngeenkcukacha malunga nokusebenzisa isibali-xesha.

Imo yoShicilelo lweNdlela zeSalathi se-LED 

• I-standBy: I-LED ebhlowu IVIMILE kwaye i-ayikhoni yeNdlela yokuSebenza inomgca kuyo
• Isitshixo esilahlekileyo/esingalunganga: I-LED eluhlaza okwesibhakabhaka IYANYANYA
• Ukusasaza: I-LED eluhlaza okwesibhakabhaka ihamba ngokuthe ngcembe

I-IR (infrared) Sync
Izibuko le-IR lelokuseta ngokukhawuleza usebenzisa umamkeli onomsebenzi okhoyo. I-IR Sync iya kudlulisela useto lokuphindaphinda, ubungakanani benyathelo, kunye nemowudi yokuhambelana ukusuka kumamkeli ukuya kumthumeli. Le nkqubo iqalwa ngumamkeli. Xa umsebenzi wongqamaniso ukhethwa kumamkeli, bamba izibuko le-IR yesithuthi kufutshane nezibuko le-IR lomamkeli. (Akukho nto yemenyu ekhoyo kwi-transmitter ukuqalisa ungqamaniso.)

PHAWULA:
Ukuba kukho ukungahambelani phakathi kommkeli kunye nomthumeli, umyalezo wemposiso uya kuvela kwi-LCD yesithuthi esichaza ukuba yintoni ingxaki.

Ukufakela ibhetri

• Isixhobo sokuhambisa sisebenzisa iibhetri zeAA. Sincoma ukusebenzisa i-lithium obona bomi bude.
• Ngenxa yokuba ezinye iibhetri zihla ngequbuliso, ukusebenzisa iPower LED ukuqinisekisa ubume bebhetri akuyi kuthembeka. Nangona kunjalo, kuyenzeka ukulandelela imeko yebhetri usebenzisa isibali-xesha sebhetri esifumanekayo kwiLectrosonics receiver.
• Ucango lwebhetri luvula ngokulula ukukhulula i-knurled knob partway de umnyango uya kujikeleza. Umnyango uphinde ususwe ngokulula ngokukhupha iqhosha ngokupheleleyo, eliluncedo xa ucoca abafowunelwa bebhetri. Uqhagamshelwano lwebhetri lunokucocwa ngotywala kunye ne-cot-ton swab, okanye i-eraser yepensile ecocekileyo. Qinisekisa ukuba ungashiyi nayiphi na intsalela ye-cotton swab okanye i-eraser crumbs ngaphakathi kwendawo.
• I-pinpoint encinci yegrisi eqhuba isilivere kwimisonto ye-thumbscrew inokuphucula ukusebenza kwebhetri kunye nokusebenza. Jonga kwiphepha lama-22. Yenza oku ukuba ufumana ukwehla kubomi bebhetri okanye ukonyuka kobushushu bokusebenza.
• Ukuba awukwazi ukufumana umthengisi wolu hlobo lwegrisi - ivenkile ye-elektroniki yasekhaya ye-ex.ample – qhagamshelana nomthengisi wakho okanye umzi-mveliso ukuze ufumane ibhodlela encinane yokulungisa.
• Faka iibhetri ngokweempawu ngasemva kwendlu. Ukuba iibhetri zifakwe ngokungachanekanga, umnyango unokuvala kodwa iyunithi ayiyi kusebenza.

Ukuqhagamshela uMthombo woMqondiso
Iimakrofoni, imithombo yomsindo yenqanaba lomgca, kunye nezixhobo zingasetyenziswa kunye nomthumeli. Jonga icandelo elinesihloko esithi Input Jack Wiring for Different Sources ngeenkcukacha kwiingcingo ezichanekileyo zeline-level sources kunye nemicrophone ukuthatha iadvan epheleleyo.tage ye-Servo Bias circuitry.

Ukufomatha iKhadi le-SD

• Amakhadi amatsha ememori e-microSDHC eza ifomathwa kwangaphambili kunye neFAT32 file inkqubo eyenzelwe ukusebenza kakuhle. Iyunithi ixhomekeke kulo msebenzi kwaye ayisoze iphazamise ukufomatha okuphantsi kwekhadi le-SD.
• Xa iDBSM/DBSMD “ifomati” ikhadi, yenza umsebenzi ofana neWindows “Quick Format” ecima yonke into. files kwaye ulungiselela ikhadi ukuze lirekhodwe. Ikhadi linokufundwa yiyiphi na ikhompyutha eqhelekileyo kodwa ukuba kukho na ukubhala, ukuhlela, okanye ukucima kwenziwa kwikhadi ngekhompyutheni, ikhadi kufuneka lihlaziywe kwakhona kunye ne-DBSM / DBSMD ukuyilungiselela kwakhona ukurekhoda. I-DBSM/DBSMD ayinakuze ifomethe ikhadi elikumgangatho ophantsi kwaye sicebisa ngokungazenzisiyo ngekhompyuter.
• Ukufomatha ikhadi ngeDBSM/DBSMD, khetha iKhadi lokuFomatha kwimenyu kwaye ucinezele MENU/SEL kwiphedi yamaqhosha.

ISILUMKISO:
Musa ukwenza ifomathi yomgangatho ophantsi (ifomati epheleleyo) ngekhompyutha. Ukwenza njalo kunokwenza ukuba imemori khadi ingasebenziseki kunye neDBSM/DBSMD rekhoda. Ngekhompyuter esekwe kwiWindows, qiniseka ukuba ujonga ibhokisi yefomati ekhawulezayo ngaphambi kokufomatha ikhadi. NgeMac, khetha iMS-DOS (FAT).

KUBALULEKILEYO
Ukufomathwa kwekhadi le-SD kuseka amacandelo adibeneyo ukuze asebenze ngokugqibeleleyo kwinkqubo yokurekhoda. I file ifomati isebenzisa i BEXT (Ulwandiso loSasazo) ifomati enedatha eyaneleyo kwiheader ye file ulwazi kunye noshicilelo lwekhowudi yexesha.

• Ikhadi le-SD, njengoko ifomathiwe yi-DBSM/DBSMD rekhoda, inokonakala ngayo nayiphi na inzame yokuhlela ngokuthe ngqo, ukutshintsha, ifomathi, okanye view i files kwikhompyuter.
• Eyona ndlela ilula yokuthintela urhwaphilizo lwedatha kukukopa i-.wav files ukusuka kwikhadi ukuya kwikhompyuter okanye ezinye iifestile okanye imidiya efomatiweyo ye-OS KUQALA. Phinda – KOPIA I FILES KUQALA!
• Musa ukuthiya igama files ngqo kwikhadi le-SD.
• Sukuzama ukuhlela i files ngqo kwikhadi le-SD.
• Sukugcina INTO kwikhadi le-SD ngekhompyuter (efana nelog yokuthatha, qaphela file,s njl) - ilungiselelwe ukusetyenziswa kwe-DBSM irekhoda kuphela.
• Musa ukuyivula i files kwikhadi le-SD ngayo nayiphi na inkqubo yomntu wesithathu efana ne-Agent ye-Wave okanye i-Audacity kwaye ivumele ugcino. Kwi-Agent ye-Wave, musa ukurhweba ngaphandle-unokuyivula kwaye uyidlale kodwa ungagcini okanye ungenise ngaphandle-I-Agent ye-Wave iya konakalisa file.
• Ngamafutshane - kufuneka AKUKHO ukuguqulwa kwedatha ekhadini okanye ukongezwa kwedatha kwikhadi kunye nantoni na ngaphandle kwe-DBSM / DBSMD rekhoda. Khuphela i files kwikhompyuter, ubhontsi wedrayivu, i-hard drive, njl. efomathiweyo njengesixhobo esiqhelekileyo se-OS KUQALA - ngoko ungahlela ngokukhululekileyo.

INKXASO YENHLOKO ye-iXML
Ukurekhodwa kuqulathe iziqwenga ze-iXML ezisemgangathweni kwishishini file iiheader, ezinemihlaba esetyenziswa kakhulu ezaliswe kuyo.

Ukuvula i-Transmitter Power

Cofa iqhosha elifutshane
Xa iyunithi icinyiwe, ukucofa okufutshane kweqhosha lamandla izakuvula iyunithi kwiNdlela yokulinda kunye nemveliso yeRF icinyiwe. Oku kuluncedo ekulungiseni useto kwiyunithi ngaphandle kokudlulisela.

Isalathisi se-RF siyadanyaza

Cofa iqhosha elide
Xa iyunithi icinyiwe, ukucofa ixesha elide kweqhosha lamandla kuya kuqalisa ukubala ukwehla ukuze uvule iyunithi ngemveliso yeRF evuliweyo. Qhubeka ubambe iqhosha kude kugqitywe ukubala ukwehla.

Ukuba iqhosha likhutshiwe phambi kokuba ukubala kugqitywe, iyunithi iya kunika amandla kunye ne-RF output icinyiwe.

Iindlela ezimfutshane zeMenu
Ukusuka kwiSikhusi esiPhambili/seKhaya, ezi ndlela zimfutshane zilandelayo ziyafumaneka:

• Ii-LEDs Vula: Cofa utolo oluthi UP
• Ii-LED zicimile: Cofa utolo PHANTSI
• Ulungiselelo lokuzuza: Cofa ixesha elide iqhosha le MENU kwaye ubambe ngelixa ulungisa inzuzo phezulu okanye ezantsi usebenzisa izitshixo zotolo
• Rekhoda: Cofa utolo EMUVA + PHEZULU ngaxeshanye
• Misa ukuRekhoda: Cinezela utolo EMUVA + PHANTSI ngaxeshanye

PHAWULA:
Iindlela ezimfutshane zokurekhoda zifumaneka kuphela kwiscreen esikhulu/sasekhaya KWAYE xa imemori khadi ye-microSDHC ifakiwe.

Ukucima amandla
Nakwesiphi na isikrini, amandla anokuvalwa ngokukhetha i-Pwr Cima kwimenyu yamandla, ubambe iqhosha laMandla ngaphakathi kwaye ilinde ibar yenkqubela phambili eshukumayo, okanye ngotshintsho olucwangcisekileyo (ukuba iqwalaselelwe lo msebenzi).

Ukuba iqhosha lamandla likhutshiwe, okanye iswitshi yepaneli ephezulu ivulwe kwakhona phambi kokuba ibha eshukumayo iqhubeke, iyunithi iya kuhlala ivuliwe kwaye i-LCD iya kubuyela kwisikrini esifanayo okanye imenyu ebiboniswe ngaphambili.

PHAWULA:
Ukuba iswitshi enokucwangciswa ikwimo eVALIWEyo, amandla asengavulwa ngeqhosha lamandla. Ukuba iswitshi ecwangcisiweyo ivuliwe, umyalezo omfutshane uya kuvela kwi-LCD.

Imiyalelo yokuSebenza iRekhoda

• Faka ibhetri
• Faka imemori khadi ye-microSDHC
• Vula amandla
• Fomata imemori khadi
• Xhuma imakrofoni kwaye uyibeke kwindawo apho iya kusetyenziswa khona.
• Yiba nentetho yomsebenzisi okanye ucule kwinqanaba elifanayo eliza kusetyenziswa kwimveliso, kwaye ulungelelanise inzuzo yegalelo ukwenzela ukuba i -20 LED idanyaze ebomvu kwiincopho eziphezulu.

Sebenzisa i-UP kunye ne-PHANSI amaqhosha otolo ukulungisa inzuzo de -20 LED idanyanyeze bomvu kwiincopho ezingxolayo.

• Cofa MENU/SEL, khetha iSDcard, kwaye Rekhoda kwimenyu
• Ukuyeka ukurekhoda, cofa MENU/SEL, khetha iSDCard, kwaye Misa; igama ESINDISIWE liyavela kwiscreen

PHAWULA: Ukurekhoda kunye nokuyeka ukuRekhoda kunokufezekiswa ngamaqhosha amfutshane ukusuka kwesikrini esikhulu/sasekhaya:

• Ukucofa ngaxeshanye kweqhosha elithi BACK + UP iqhosha lotolo: Qalisa ukurekhoda
• Ukucofa ngaxeshanye kweqhosha elithi BACK + PHANTSI iqhosha lotolo: Misa ukurekhoda

Imephu yeMenu yeDBSM/DBSMD

• Ukusuka kwifestile engundoqo, cofa u-MENU/SEL.
• Sebenzisa utolo oluthi PHEZULU/ PHANTSI ukukhetha into.

IiNkcukacha zeSkrini seMenu

Imenyu ephezulu
Ukusuka kwiscreen esiMiselweyo, ukucofa MENU/SEL kuya kufikelela kwiMenu ePhezulu. Imenyu ephezulu ivumela umsebenzisi ukuba afikelele kwiimenyu ezisezantsi ezahlukeneyo ukulawula iyunithi.

Imenyu yokufaka
Ukusuka kwi-TopMenu, sebenzisa i kwaye amaqhosha otolo ukuqaqambisa INPUT kwaye ucinezele MENU/SEL.

Ukulungelelanisa iNgeniso yeNgeniso
Ii-bicolor Modulation LEDs kwiphaneli yolawulo zibonelela ngembonakalo yenqanaba lesandi somsindo ukungena kwi-transmitter. Ii-LED ziya kukhanya nokuba zibomvu okanye ziluhlaza ukubonisa amanqanaba omodareyitha njengoko kubonisiwe kwitheyibhile elandelayo.

PHAWULA: Ukumodareyitha ngokupheleleyo kuphunyezwa kwi-0 dB xa i-"-20" i-LED ijika ibebomvu kuqala. I-limiter inokuphatha ngokucocekileyo iincopho ukuya kuthi ga kwi-30 dB ngaphezulu kwale ndawo.

Kungcono ukuba uhambe ngale nkqubo ilandelayo kunye ne-transmitter kwimowudi yokulinda ukuze kungabikho audio iya kungena kwinkqubo yesandi okanye irekhoda ngexesha lohlengahlengiso.

1. Ngeebhetri ezitsha kwi-transmitter, vula iyunithi kwimowudi yokulinda (jonga icandelo langaphambili Ukuvula Amandla kunye nokuvala).
2. Yiya kwiGain setup screen.
3. Lungisa umthombo womqondiso. Misa imayikrofoni ngendlela eya kusetyenziswa ngayo ekusebenzeni kokwenyani kwaye umsebenzisi athethe okanye acule kwelona nqanaba liphezulu liya kwenzeka ngexesha lokusetyenziswa, okanye usete inqanaba lemveliso yesixhobo okanye isixhobo somsindo ukuya kwinqanaba eliphezulu eliya kusetyenziswa. .
4. Sebenzisa i kwaye amaqhosha otolo ukulungisa inzuzo de i -10 dB ikhazimle luhlaza kwaye i -20 dB LED iqala ukudanyaza bomvu ngexesha lencochoyi yesandi esingxolayo.
5. Nje ukuba ingeniso yomsindo isetiwe, isiginali inokuthunyelwa ngenkqubo yesandi kuhlengahlengiso lwenqanaba elipheleleyo, useto lokubeka iliso, njl.
6. Ukuba inqanaba lemveliso yomsindo yomamkeli liphezulu kakhulu okanye liphantsi, sebenzisa kuphela ulawulo kumamkeli ukwenza uhlengahlengiso. Ngalo lonke ixesha shiya uhlengahlengiso lokufumana isidluliseli ngokwezi miyalelo, kwaye ungalutshintshi ukulungelelanisa inqanaba lemveliso yeaudio yomamkeli.

Ukukhetha i-Low Frequency Roll-off
Kusenokwenzeka ukuba indawo yokuqengqeleka ephantsi-frequency inokuchaphazela ukusetwa kwenzuzo, ngoko yinto eqhelekileyo ukwenza olu lungelelwaniso phambi kokulungelelanisa inzuzo yegalelo. Indawo ekuqhutyekwa kuyo i-roll-off inokumiselwa ukuba ithi:

• LF 20 20 Hz
• LF 35 35 Hz
• LF 50 50 Hz
• LF 70 70 Hz
• LF 100 100 Hz
• LF 120 120 Hz
• LF 150 150 Hz

I-roll-off ihlala ihlengahlengiswa yindlebe ngelixa ibeka iliso kwi-audio.

Ukukhetha i-Audio polarity
I-Audio polarity inokuguqulwa kwi-transmitter ukuze i-audio ixutywe kunye nezinye ii-microphone ngaphandle kokucoca ngekama. I-polarity inokuphinda iguqulwe kwiziphumo zomamkeli.

Ukukhetha LineIn/Isixhobo
Igalelo leAudio linokukhethwa njengeLineIn okanye iNqanaba leSixhobo.

Xmit Menu
Sebenzisa i kwaye amaqhosha otolo ukukhetha iMenu yokuThumela kwimenyu ephezulu.

Ukukhetha Ukuphindaphinda
Ukuseta isikrini sokhetho lwefrikhwensi ibonelela ngeendlela ezininzi zokukhangela amaza akhoyo.

Ukucofa i-MENU/SEL kuya kutshintsha imimandla yamaxesha amaninzi. I-frequency ye-MHz iya kutshintsha kumanyathelo e-1 MHz, i-frequency ye-KHz iya kutshintsha ngamanyathelo angama-25 KHz.

Ukuseta iNtshukumo yokuPhuma kwamandla
Amandla emveliso anokumiselwa ukuba:

• 10, 25 okanye 50 mW, okanye HDM (iMowudi yoXinaniso oluPhezulu)

RF ivuliwe?
Ugqithiso lweRF lunokuvulwa okanye luvalwe ngokusebenzisa i kwaye amaqhosha otolo.

IMenyu eChwethekileyo

Ukukhetha iMowudi ehambelanayo

• Sebenzisa i kwaye amaqhosha otolo ukukhetha indlela efunwayo, emva koko ucinezele iqhosha EMVA kabini ukubuyela kuMmandla we Window.
• Iimowudi zokuhambelana zezi zilandelayo:
  I-DBSM/DBSMD:
  • Standard Mono Digital D2
  • Imo yoxinaniso oluphezulu lweHDM

Imowudi yeHDM (Ugqithiso loXinano oluPhezulu)
Le modi yothumelo ikhethekileyo kunye namandla aphantsi eRF anxulumene ne-2mW ivumela umsebenzisi ukuba "aqokelele" iiyunithi ezininzi kwindawo encinci kakhulu yespectrum. Okusemgangathweni, i-ETSI-ethobela i-RF abathwali bathatha malunga ne-200 kHz ye-bandwidth ekhoyo, ngelixa i-HDM ithatha malunga nesiqingatha saloo, okanye i-100 kHz, kwaye ivumela isithuba esingqongqo kakhulu sesiteshi.

SD Card Menu
IMenu yeKhadi le-SD inokufumaneka kwi-TopMenu. Iqulethe imisebenzi yokurekhoda eyahlukeneyo, file ulawulo, kunye namagama.

Rekhoda
Ukukhetha oku kuya kuqalisa iyunithi yokurekhoda. Ukuyeka ukurekhoda, cofa MENU/SEL, khetha iSDCard, kwaye Misa; igama ESINDISIWE liyavela kwiscreen.

PHAWULA:
Ukurekhoda kunye nokuyeka ukuRekhoda kunokufezekiswa ngamaqhosha amfutshane ukusuka kwesikrini esikhulu/sasekhaya:

• Ukucofa ngaxeshanye kweqhosha elithi BACK + UP iqhosha lotolo: Qalisa ukurekhoda
• Ukucofa ngaxeshanye kweqhosha elithi BACK + PHANTSI iqhosha lotolo: Misa ukurekhoda

Files
Esi sikrini sibonisa ekhoyo files kwikhadi le-SD. Ukukhetha a file izakubonisa iinkcukacha malunga ne file.

Viewing Ithatha
Sebenzisa UP kunye no PHANTSI amatolo ukuguqulela kunye MENU/SEL ukuya view kuthatha.

Ukudlala kwakhona urekhodisho, susa imemori khadi uze ukope i files kwikhompyutha enevidiyo okanye isoftwe yokuhlela emanyelwayo efakiweyo.

Ukuseta iSigcawu kwaye uthathe inombolo
Sebenzisa i-UP kunye ne-PHANSI iintolo ukuqhubela phambili iSicenelo kunye nokuThatha kunye ne-MENU/SEL ukuguqula. Cofa iqhosha elithi BACK ukubuyela kwimenyu.

Ifomathi
Ifomatha ikhadi lememori le-microSDHC.

ISILUMKISO:
Lo msebenzi ucima nawuphi na umxholo okwikhadi lememori le-microSDHC.

Irekhodwe File Ukunikwa amagama
Khetha ukunika igama elirekhodiweyo files ngenani lolandelelwano, ixesha lewotshi, okanye indawo kunye nethatha.

Ulwazi lwe-SD
Ulwazi malunga nekhadi lememori ye-microSDHC kuquka indawo eseleyo kwikhadi.

Layisha Iqela
Khetha igama leqela le-frequency kwikhadi le-SD oza kulilayisha.

Gcina iQela
Khetha igama leqela lamaxesha oza kuligcina kwikhadi le-SD.

TCode Imenyu

TC Jam (jam timecode)

• Xa i-TC Jam ikhethiwe, i-JAM NGOKU iya kuqhwanyaza kwi-LCD kwaye iyunithi ilungele ukuvumelanisa kunye nomthombo wekhowudi yexesha. Qhagamshela umthombo wekhowudi yexesha kwaye ulungelelwaniso luya kwenzeka ngokuzenzekelayo. Xa ungqamaniso luphumelele, umyalezo uya kuboniswa ukuqinisekisa ukusebenza.
• I-timecode defaults ku-00:00:00 kumandla-phezulu ukuba akukho mthombo wekhowudi yexesha elisetyenziselwa ukudibanisa iyunithi. Isalathiso sexesha sifakwe kwimetadata ye-BWF.

PHAWULA:
Igalelo lekhowudi yexesha le-DBSM likwi-5-pin ye-mic input. Ukuze usebenzise ikhowudi yexesha, susa isinxibelelanisi semakrofoni kwaye ubeke endaweni yaso ngentambo yeadaptha yongqamaniso yekhowudi yexesha. Sincoma i-MCTCTA5BNC okanye i-MCTCA5LEMO5 (jonga ii-Optional Accessories). Iingcingo zombane zibhalwe kwiphepha le-16.

Ukumisela inqanaba lesakhelo

Umlinganiselo wesakhelo uchaphazela uzinziso lwesalathiso sexesha kwi. I-BWF file imethadatha kunye nokuboniswa kwekhowudi yexesha. Olu khetho lulandelayo luyafumaneka:

• 30
• 23.976l
• 24
• 29.97
• 30DF
• 25
• 29.97DF

PHAWULA:
Ngelixa kunokwenzeka ukutshintsha ireyithi yesakhelo, olona sebenziso luqhelekileyo luya kuba kukujonga umlinganiselo wesakhelo esifunyenwe ngexesha lamva nje le-timecode jam. Kwiimeko ezinqabileyo, kunokuba luncedo ukuguqulela umyinge wesakhelo apha, kodwa qaphela ukuba iingoma zesandi zinokungangqamani ngokuchanekileyo kunye nemilinganiselo yesakhelo esingafanelekanga.

Sebenzisa iwotshi
Iwashi lexesha le-DBSM kunye nekhalenda (RTCC) ayinakuthenjwa njengomthombo wekhowudi yexesha elichanekileyo. Sebenzisa iClock kufuneka isetyenziswe kuphela xa kungekho mfuneko yexesha lokuvumelana nomthombo wangaphandle wekhowudi yexesha.

Imenyu ye-IR&Sitshixo

SendFreq
Cofa u-MENU/SEL ungqamaniso lwe-Frequency kwesinye isidluliseli okanye umamkeli nge-IR port.

Thumela konke
Cofa u-MENU/SEL ukuze ungqamanise: Ukuphindaphinda, Igama loThutho, iTalkback inikwe amandla, kunye neMowudi yokuNhambelana ukuya kwesinye isidluliseli okanye umamkeli ngezibuko le-IR.

PHAWULA:
I-SendAll ayithumeli isitshixo soguqulelo oluntsonkothileyo. Oku kufuneka kwenziwe ngokwahlukeneyo.

GetFreq
Cofa u-MENU/SEL ungqamaniso lwe-Frequency kwesinye isidluliseli okanye umamkeli nge-IR port.

GetAll
Cofa u-MENU/SEL ukuze ungqamanise: Ukuphindaphinda, Igama loThutho, iTalkback inikwe amandla, kunye neMowudi yokuQhubelana ukusuka kwesinye isihambisi okanye umamkeli ngezibuko le-IR.

Uhlobo oluphambili
I-DBSM/DBSMD ifumana isitshixo soguqulelo oluntsonkothileyo nge-IR port ukusuka kumamkeli ovelisa isitshixo. Qala ngokukhetha uhlobo oluphambili kumamkeli kwaye uvelise isitshixo esitsha (uhlobo lwesitshixo lubhalwe UMGAQO-NKQUBO OWUNDOQO kummkeli we-DSQD).

Cwangcisa UHLOBO LWENKQUBO ehambelanayo kwi-DBSM/DBSMD kwaye udlulisele isitshixo kumamkeli (SYNC KEY) ukuya kwi-DBSM/DBSMD ngokusebenzisa izibuko ze-IR. Umyalezo wokuqinisekisa uya kuboniswa kwidispleyi yomamkeli ukuba ugqithiso luphumelele. I-audio ethunyelwayo iya kuguqulelwa ngokuntsonkothileyo kwaye inokumanyelwa kuphela ukuba umamkeli uneqhosha elihambelanayo lofihlo.

Inkqubo yokubethela kwiindlela zeLectrosonics Digital D2, DCHX, kunye ne-HDM inokumiselwa ngeendlela ezine ezahlukeneyo, ezinqunywe yiparameter eyaziwa ngokuba yiNdlela ePhambili. Iindidi ezine eziphambili zisusela kukhuseleko oluncinci kodwa olulunge kakhulu, ukuya kwezona zikhuselekileyo kodwa zilula. Ngezantsi kukho iinkcazo zeeNdidi ezine eziphambili kunye nendlela ezisebenza ngayo.

• Universal: Olu lolona hlobo lwesitshixo esihlala sihleli, esona sisebenziseka lula, kwaye sikhuselekile. Ngelixa uguqulelo oluntsonkothileyo lwenziwa ngobuchwephesha kwaye iskena okanye idemodulator elula ayinakutyhila umxholo wophawu, unxibelelwano alukhuselekanga ngenene. Oku kungenxa yokuba zonke iimveliso zeLectrosonics ezisebenzisa uhlobo lwesitshixo se-Universal zisebenzisa eli qhosha lifanayo “lokufihlakala” linye. Ngolu hlobo lwesitshixo olukhethiweyo, izitshixo akufuneki zidalwe okanye zitshintshwe, kunye nezixhobo ezingenazintambo zingasetyenziswa ngaphandle kokuqwalaselwa kwifitsha ye-encryption.
• Kwabelwana: Le yeyona ndlela ilula yoguqulelo olunokusetyenziswa ngelixa usebenzisa isitshixo esiveliswe ngokukodwa. Olu hlobo oluphambili lunikeza ukhuseleko olubalaseleyo kunye nokuguquguquka okukhulu. Emva kokuba isitshixo senziwe, sinokwabelwana ngenani elingenamkhawulo lamaxesha naso nasiphi na isixhobo esihambelanayo esinokuthi, ngokulandelayo, sikwazi ukwabelana ngesitshixo. Oku kuluncedo ngakumbi xa abamkeli abaninzi banokufuna ukuchola ii-transmitters ezahlukeneyo.
• Umgangatho: Uhlobo lwesitshixo esisemgangathweni lubonelela ngokhuseleko olongeziweyo, ngexabiso lobunzima obuthile. Izitshixo ezisemgangathweni "zilawulwa kwimeko", evumela ukuba i-hardware ikhusele "kuhlaselo oluhlukeneyo". Isitshixo esisemgangathweni sinokuthunyelwa kuphela sisixhobo esidale, kwaye kuphela ukuya kumaxesha angama-256. Ngokungafaniyo nezitshixo ekwabelwana ngazo, izixhobo ezifumana iqhosha le-Stan-dard azinako ukulidlulisela.
• I-Volatile: Uhlobo lwesitshixo se-Volatile lolona lukhuseleke kakhulu, kwaye lusebenziseka kancinci. Izitshixo eziguquguqukayo ziziphatha ngokufanayo nezitshixo ezisemgangathweni, ngaphandle kokuba azigcinwanga. Isixhobo esicinyiweyo ngelixa usebenzisa isitshixo seVolatile siya kubuya sivuleke singenasitshixo. Ukuba isixhobo sokuvelisa isitshixo sishiywe sivuliwe, isitshixo sinokuphinda kwabelwane ngeeyunithi kwisistim eziphulukene nezitshixo zazo. Nje ukuba zonke izixhobo zisebenzise iqhosha elinikiweyo le-Volatile licinyiwe, elo qhosha liyatshatyalaliswa. Oku kungafuneka kolunye ufakelo olukhuseleke kakhulu.

WipeKey
Lo mba wemenyu ufumaneka kuphela ukuba iSidibo seSitshixo simiselwe kuMgangatho, eKwabelwana ngaso, okanye kwiVolatile. Khetha Ewe ukusula iqhosha langoku kwaye wenze i-DBSM/DBSMD ifumane iqhosha elitsha.

Seta iMenu

I-AutoOn
Cinezela u-MENU/SEL ukuguqula i-AutoOn ivule okanye ivale.

Ukude
Cinezela u-MENU/SEL ukuguqula i-Remote "dweedle tone" ivule okanye icime.

Uhlobo lweBatt
Cofa MENU/SEL ukukhetha nokuba yi-Alkaline okanye ibhetri yeLithium. Iibhetri zeLithium ziyacetyiswa.

Ikloko
Cofa MENU/SEL ukuseta iwotshi (ixesha kunye nomhla).

Ukutshixa/Ukuvula utshintsho kwiSetingi
Utshintsho kwisethingi lungatshixwa kwiqhosha leMenyu yeqhosha laMandla.

Xa utshintsho lutshixiwe, ulawulo oluninzi kunye neentshukumo zisenokusetyenziswa:

• Iisetingi zisenokuvulwa
• Iimenyu zisenokukhangelwa
• Xa itshixiwe, AMANDLA ANOKUVALWA KUPHELA ngokususa iibhetri.
• Imowudi etshixiweyo “emnyama” ithintela umboniso ukuba ungaveli xa amaqhosha ecofa. Phuma ngokubamba UP+PHANSI imizuzwana emi-3. Ngokungafaniyo nemowudi etshixiweyo eqhelekileyo, imowudi “eMnyama” etshixwayo ayiqhubeki kumjikelo wamandla.

I-DispOff
Cinezela u-MENU/SEL ukuguqula isici se-DisplayOff phakathi kwe-5 kunye ne-30 imizuzwana, okanye usete ukuba uhlale uvuliwe.

Ukukhanya kwe-LED
Ukusuka kwesikrini semenyu ephambili, ukucofa ngokukhawuleza kweqhosha le-UP elitolo lijika ii-LED zephaneli yokulawula. Ukucofa ngokukhawuleza utolo lweqhosha elithi DOWN lucima. Amaqhosha aza kuvalwa ukuba UKHISHIWE ukhetho lukhethiwe kwiqhosha leMenu yeqhosha.

Ukuhlala kukho
Cinezela MENU/SEL ukubuyisela iMiyolelo (ifektri) izicwangciso.

Malunga
Cinezela MENU/SEL ukubonisa imodeli, inguqulelo ye-firmware, inguqulelo yesoftware, kunye nenombolo yesiriyali.

5-Pin Input Jack Wiring

• I-microphone ze-Lavalier kunye ne-adapter cabling esetyenziswa kunye ne-digital bodypack transmitters kufuneka ibe nocingo lwekhaka oluqhagamshelwe kwiqokobhe leplagi yemakrofoni.
• Oku kuya kunciphisa amandla eRF asasazeke kwintambo yogcino lwemakrofoni ukusuka ekubuyeleni kwi-trans-mitter ngegalelo le-audio.
• Abathwali beDigital RF baqulathe omabini amacandelo e-FM kunye ne-AM kwaye ukhuselo olukhulu lwemakrofoni luyafuneka ukoyisa uphazamiseko lwamaza osasazo lwerediyo. Imizobo yocingo ebandakanyiweyo kweli candelo imele i-wiring eyisiseko eyimfuneko kwiintlobo eziqhelekileyo zeemakrofoni kunye nezinye izinto ezivakalayo. Ezinye ii-microphone zinokufuna ii-jumpers ezongezelelweyo okanye utshintsho oluncinci kwimizobo ebonisiweyo.
• Akunakwenzeka ukuba uhlale usexesheni ngokupheleleyo kutshintsho olwenziwa ngabanye abavelisi kwiimveliso zabo, ngaloo ndlela unokudibana ne-microphone eyahlukileyo kule miyalelo. Ukuba oku kuyenzeka nceda ufowunele inombolo yethu engahlawulelwayo edweliswe phantsi kweNkonzo kunye noLungiso kule ncwadana okanye undwendwele yethu webindawo e: www.lectrosonics.com.

Ukufakwa kweentambo zomsindo wejack:

• IPIN 1
  Ikhaka (umhlaba) kwimibhobho ye-electret lavaliere enomkhethe. Ikhuselo (umhlaba) lweemicrophone eziguquguqukayo kunye namagalelo omgangatho womgca.
• IPIN 2
  Umkhethe voltagUmthombo wemibhobho ye-electret lavaliere enomkhethe ongasebenzisi i-servo bias circuitry kunye nevoltage umthombo we-4-volt servo bias wiring.
• IPIN 3
  Igalelo lenqanaba lemakrofoni kunye nonikezelo lwe-bias.
• IPIN 4
  • Umkhethe voltage umkhethi wePin 3.
  • Iphini 3 voltage ixhomekeke kuqhagamshelo lwePin 4.
  • IPin 4 ibotshelelwe kwiPin 1: 0 V
  • IPin 4 Vula: 2 V
  • I-Pin 4 ukuya kwiPin 2: 4 V
• IPIN 5
  Igalelo lenqanaba lomgca kwiidekhi zeteyiphu, iziphumo zomxube, izixhobo zomculo, kunye nekhowudi yexesha lokuxinana.

Phawula:
Ukuba usebenzisa i-boot yothuli, susa i-rubber strain relief efakwe kwi-cap ye-TA5F, okanye i-boot ayiyi kungena kwindibano.

Ukuhlohla isiqhagamshelo:

1. Ukuba kuyimfuneko, susa isinxibelelanisi esidala kwikhebula lemakrofoni.
2. Shelelisela isilayidi sothuli kwintambo ye-microphone enesiphelo esikhulu esijonge kwisidibanisi.
3. Ukuba kukho imfuneko, tyibilikisa i-1/8-intshi emnyama yetyhubhu eshwabeneyo kwintambo yemicrophone. Le ityhubhu iyafuneka kwezinye iintambo zedayamitha ezincinci zokuqinisekisa ukuba kukho indawo ehlala intle kwibhuthi yothuli.
4. Slayida i-backshell phezu kwentambo njengoko kubonisiwe ngasentla. Slayida isigqubuthelo phezu kwentambo phambi kokuba udibanise iingcingo kwizikhonkwane ezikufakelweyo.
5. Solder iingcingo kunye resistors ukuba izikhonkwane kwi ufakelo ngokwemizobo eboniswe kwi Wir-ing Hookups kwimithombo eyahlukeneyo. Ubude be-.065 OD i-tubing ecacileyo ifakiwe ukuba ufuna ukufaka i-resistor lead lead okanye ucingo lwekhaka.
6. Ukuba kuyimfuneko, susa isiqabu serabha kwi-backshell ye-TA5F ngokuyikhupha nje.
7. Beka i-insulator kwindawo yokufaka. Slayida intambo clamp ngaphezulu kunye neye-insulator kunye necrimp njengoko kubonisiwe kwiphepha elilandelayo.
8. Faka i-insulator/cl edityanisiweyoamp kwilatchlock. Qinisekisa ukuba ithebhu kunye ne-slot zilungelelanisa ukuvumela ukufakwa ukuba kuhlale ngokupheleleyo kwisitshixo se-latch. Tyala iqokobhe elingasemva kwisitshixo.

I-Microphone Cable Cable Termination for Non-Lectrosonics Microphones

I-TA5F yokudibanisa iNdibano

Imiyalelo yokuhlubula iNtambo yeMic

I-crimping kwi-Shield kunye ne-Insulation
Hlubula kwaye ubeke intambo ukuze i-clamp inokunqanda ukuqhagamshelana nekhaka lentambo ye-mic kunye nokugquma. Uqhagamshelwano lwekhaka lunciphisa ingxolo ngezinye ii-microphone kunye ne-insulation clamp kwandisa ubunzima.

PHAWULA:
Olu kupheliswa lujoliswe kubathumeli be-UHF kuphela. Ii-VHF transmitters ezine-5-pin jacks zifuna ukupheliswa okwahlukileyo. Ii-microphone ze-Lectrosonics lavaliere ziyapheliswa ukuze zihambelane ne-VHF kunye ne-UHF transmitters. I-M152/7005P ifakwe iingcingo ngekhaka kwiqokobhe lesiqhagamshelo njengoko kubonisiwe.

Input Jack Wiring kwimithombo eyahlukeneyo

• Ukongeza kwi-microphone kunye ne-line-level wiring hook-ups eboniswe ngezantsi, i-Lectrosonics yenza inani leentambo kunye ne-adapters kwezinye iimeko ezifana nokudibanisa izixhobo zomculo (iigita, ii-bass guitar, njl.) kwi-transmitter. Ndwendwela www.lectrosonics.com kwaye ucofe kuZincedisi, okanye ukhuphele ikhathalogu enkulu.
• Ulwazi oluninzi malunga ne-microphone wiring lukwafumaneka kwicandelo le-FAQ le webindawo e: http://www.lectrosonics.com/faqdb
• Landela imiyalelo yokukhangela ngemodeli yenombolo okanye ezinye iindlela zokukhangela.

I-Wiring ehambelanayo kuzo zombini iiNgeniso ze-Servo Bias kunye nee-Transmitters zakwangoko:

Ukufakwa kweeNcingo eziLula-Inokusetyenziswa KUPHELA ngeeNgeniso ze-Servo Bias:
I-Servo Bias yaziswa ngo-2005 kwaye zonke ii-transmitter ezine-5-pin inputs zakhiwe ngolu phawu ukususela ngo-2007.

I-Microphone RF Bypassing
Xa isetyenziswa kwi-transmitter engenazingcingo, i-microphone element ikumganyana we-RF ivela kumthumeli. Ubume bemibhobho ye-electret ibenza babe buthathaka kwi-RF, enokubangela iingxaki nge-microphone / ukuhambelana kwe-transmitter. Ukuba imayikrofoni ye-electret ayilwanga kakuhle ukuba isetyenziswe ngeetransmitha ezingenazingcingo, kunokuba yimfuneko ukuba kufakwe i-chip capacitor kwi-mic capsule okanye isinxibelelanisi ukuthintela iRF ekungeneni kwi-capsule ye-electret.

Ezinye ii-mics zifuna ukhuseleko lwe-RF ukugcina isignali yerediyo ingachaphazeli i-capsule, nangona i-transmitter input circuitry sele igqithelwe yi-RF. Ukuba imakrofoni ifakwe intambo njengoko kuyalelwe, kwaye unobunzima bokuncwina, ingxolo ephezulu, okanye ukungaphenduli kakuhle kwamaza, iRF isenokuba ngunobangela.

Olona khuselo lweRF luphunyezwa ngokufakela i-RF bypass capacitors kwi-mic capsule. Ukuba oku akunakwenzeka, okanye ukuba useneengxaki, ii-capacitors zinokufakelwa kwi-mic pins ngaphakathi kwendlu yokudibanisa i-TA5F. Jonga kumzobo ongezantsi kwindawo echanekileyo ye-capacitors. Sebenzisa i-330 pF capacitors. IiCapacitors ziyafumaneka kwiLectrosonics. Nceda uchaze inombolo yenxalenye yesimbo sokukhokela esifunekayo.

• Ii-capacitors ezikhokelayo: P/N 15117
• Ii-capacitors ezingenantambo: P/N SCC330P

Zonke ii-mics ze-Lectrosonics lavaliere sele zidlulile kwaye azidingi nayiphi na i-capacitor eyongezelelweyo efakwe ekusebenzeni ngokufanelekileyo.

Iimpawu zeNqanaba lomgca
Iingcingo zomgangatho womgca kunye neempawu zesixhobo zezi:

• Umqondiso oshushu ukuqhobosha 5
• Umqondiso Gnd ukuqhobosha 1
• UPin 4 utsibe ukuya ku-1

Oku kuvumela amanqanaba omqondiso ukuya kuthi ga kwi-3V RMS ukuba isetyenziswe ngaphandle kokunciphisa.

PHAWULA ngamagalelo omgangatho womgca kuphela (hayi isixhobo): Ukuba igumbi lentloko elingaphezulu liyafuneka, faka i-20 k resistor kuthotho nge-pin 5. Faka esi sixhathisi ngaphakathi kwe-TA5F isinxibelelanisi ukunciphisa ukucofa ingxolo. I-resistor iya kuba nempembelelo encinci okanye ingabikho kwisignali ukuba igalelo limiselwe isixhobo.

Uhlaziyo lweFirmware

Uhlaziyo lweFirmware lwenziwa kusetyenziswa imemori khadi ye-microSDHC. Jonga imbali yoHlaziyo kwi webindawo yokumisela ukuba loluphi uhlaziyo ekufuneka uyenzile.

PHAWULA:
Qinisekisa ukuba uneebhetri ezintsha kwiyunithi yakho ngaphambi kokuba uqalise inkqubo yohlaziyo. Ukusilela kwebhetri kuya kuphazamisa kwaye kusenokonakalisa uhlaziyo file.

Khuphela inguqulo ye-firmware efanelekileyo. Unzip kwaye ukope uhlaziyo lwe-firmware olulandelayo files kwi drive kwikhompyuter yakho:

• dbsm vX_xx.hex luhlaziyo lwe-firmware file, apho "X_xx" yinombolo yohlaziyo.
• dbsm_fpga_vX.mcs luhlaziyo lwebhodi yeqabane file, apho u-“X” yinombolo yohlaziyo.

Ekhompyutheni:

1. Yenza iFomathi eKhawulezayo yekhadi. Kwi-Windows-based system, oku kuya kufomatha ikhadi ngokuzenzekelayo kwifomathi ye-FAT32, esemgangathweni yeWindows. KwiMac, unokunikwa iinketho ezininzi. Ukuba ikhadi sele lifomathiwe kwiWindows (FAT32) - liya kuba greyed ngaphandle - ngoko akukho mfuneko yokuba wenze nantoni na. Ukuba ikhadi likwenye ifomathi, khetha iWindows (FAT32) uze ucofe "Cima". Xa ifomati ekhawulezayo kwikhompyuter igqityiwe, vala ibhokisi yencoko yababini kwaye uvule i file umkhangeli zincwadi.
2. Khuphela i-dbsm vX_xx.hex kunye ne-dbsm_fpga_ vX.mcs files kwikhadi lememori, uze ulikhuphe ngokukhuselekileyo ikhadi kwikhompyuter.

Kwi-DBSM:

1. Shiya i-DBSM icinyiwe kwaye ufake imemori khadi ye-microS-DHC kwindawo yokubeka.
2. Bamba phantsi omabini amaqhosha aphezulu kunye ne-PHANTSI kwirekhoda kwaye uvule amandla.
3. Umshicileli uya kuqalisa kwimowudi yohlaziyo lwe-firmware ngolu khetho lulandelayo kwiLCD:
   • Uhlaziyo-Ibonisa uluhlu olusolekayo lohlaziyo files kwikhadi.
   • Ukucinywa kombane-Kuphuma kwimowudi yohlaziyo kwaye ucime umbane.
     PHAWULA: Ukuba iyunithi yekhusi sibonisa IKHADI LEFORMAT? cima iyunithi kwaye uphinda inyathelo lesi-2. Ubungacinezeli ngokufanelekileyo PHEZULU, PHANTSI, kunye naMandla ngaxeshanye.
4. Sebenzisa amaqhosha ukuze ukhethe Hlaziya. Sebenzisa i-UP kunye ne-PHANSI amaqhosha otolo ukukhetha okufunayo file (kufuneka zihlaziywe ngabanye) kwaye cinezela MENU/SEL ukufaka i-firmware. I-LCD iya kubonisa imiyalezo yesimo ngelixa i-firmware ihlaziywa.
5. Xa uhlaziyo lugqityiwe, i-LCD iya kubonisa lo myalezo: UHLAZIYA NGEMPUMELELO UKUSUSA IKHADI. Vula ucango lwebhetri, susa imemori khadi, uze uyibuyisele ngaphakathi kwaye uvale ucango.
6. Phinda amanyathelo 1-5 ukuhlaziya enye file.
7. Vula iyunithi kwakhona. Qinisekisa ukuba inguqulo ye-firmware yahlaziywa ngokuvula iqhosha leMenyu ye-Power Button kunye nokuhamba uye kwi-About item. Jonga kwiphepha lesi-6.
8. Njengoko uphinda ufaka ikhadi elihlaziyiweyo kwaye uvule amandla kwakhona, i-LCD iya kubonisa umyalezo okhuthaza ukuba ufomethe ikhadi:
   Ikhadi lokufomatha? (fileilahlekile)
   • Hayi
   • Ewe

Ikhadi lihlala lihleli kwifomati yeDATA emva kohlaziyo. Ukuba unqwenela ukurekhoda iaudio kwikhadi, kufuneka uyifomethe kwakhona. Khetha Ewe kwaye ucinezele MENU/SEL ukufomatha ikhadi. Xa inkqubo igqityiwe, i-LCD iya kubuyela kwi-Main Window kwaye ilungele ukusebenza okuqhelekileyo. Ukuba ukhetha ukugcina ikhadi njengoko linjalo (DATA), ungalisusa ikhadi ngeli xesha kwaye uhlaziye elinye file ukuba kuyimfuneko.

I-Bootloader Files:
Inkqubo yohlaziyo lwe-firmware ilawulwa yinkqubo ye-bootload-er - kwiimeko ezinqabileyo kakhulu, unokufuna ukuhlaziya i-bootloader.

ISILUMKISO:
Ukuhlaziya i-bootloader kunokonakalisa iyunithi yakho ukuba iphazamisekile. Musa ukuhlaziya i-bootloader ngaphandle kokuba ucetyiswe ukuba wenze njalo ngumzi-mveliso.

• dbsm_boot vX_xx.hex sisishicileli sokuqala file

Landela inkqubo efanayo kunye nohlaziyo lwe-firmware kwaye ukhethe i-dbsm_boot file.

Inkqubo yoBuyiselo

Kwimeko yokungaphumeleli kwebhetri, ngelixa iyunithi irekhoda, inkqubo yokubuyisela iyafumaneka ukubuyisela ukurekhoda kwifomathi efanelekileyo. Xa ibhetri entsha ifakwe kwaye iyunithi ivuliwe, irekhoda iya kubona idatha elahlekileyo kwaye ikuxelele ukuba uqhube inkqubo yokubuyisela. I file kufuneka ihlawulwe okanye ikhadi aliyi kusetyenziswa kwi-DBSM/DBSMD.

Okokuqala, iya kufunda:
Ukurekhodwa okuphazamisekileyo kufunyenwe

Umyalezo weLCD uya kubuza:

Ukuchacha?
usetyenziso olukhuselekileyo jonga incwadana

Uya kuba nokukhetha uHayi okanye u-Ewe (Hayi kukhethwa njengokungagqibekanga). Ukuba unqwenela ukubuyisela i file, sebenzisa utolo olu PHANTSI iqhosha ukukhetha Ewe, uze ucinezele MENU/SEL. Iwindow elandelayo iya kukunika ukhetho lokubuyisela yonke okanye inxalenye ye file. Amaxesha angagqibekanga abonisiwe lolona qikelelo lweprosesa apho i file wayeka ukurekhoda. Iiyure ziya kuphawulwa kwaye ungavuma ixabiso elibonisiweyo okanye ukhethe ixesha elide okanye elifutshane. Ukuba awuqinisekanga, vele wamkele ixabiso elibonisiweyo njengokungagqibekanga.

Cofa u-MENU/SEL kwaye imizuzu emva koko iphawulwe. Unokwandisa okanye unciphise ixesha lokubuyiselwa. Kwiimeko ezininzi unokwamkela ngokulula amaxabiso abonisiweyo kunye ne file iya kubuyiselwa. Emva kokuba wenze ukhetho lwakho lwexesha, cinezela MENU/SEL kwakhona. IHAMBA encinci! I-sym-bol izakuvela ecaleni kweqhosha letolo elithi DOWN. Ukucofa iqhosha kuya kuqalisa i file ukuchacha. Ukubuyiselwa kuya kwenzeka ngokukhawuleza kwaye uya kubona:

UkuBuyisa Kuphumelele

Inqaku elikhethekileyo:
Files ngaphantsi kwemizuzu emi-4 ubude bunokuchacha ngedatha eyongezelelweyo "ifakwe" ukuya ekupheleni file (ukusuka kurekhodisho lwangaphambili okanye idatha ukuba ikhadi belisetyenziswe ngaphambili). Oku kunokupheliswa ngempumelelo kwisithuba ngokucima okulula okungafunekiyo "ingxolo" eyongezelelweyo ekupheleni kwekliphu. Ubude obuncinane obufunyenweyo buya kuba ngumzuzu omnye. Umzekeloampkwaye, ukuba ukurekhodwa kuyimizuzwana engama-20 kuphela ubude, kwaye ukhethe umzuzu omnye kuya kubakho imizuzwana engama-20 erekhodiweyo kunye nemizuzwana engama-40 eyongezelelweyo yenye idatha kunye okanye izinto zakudala file. Ukuba akuqinisekanga malunga nobude bokurekhoda ungagcina ixesha elide file -kuya kuba lula ngakumbi "inkunkuma" ekupheleni kwekliphu. Le "nkunkuma" inokubandakanya idatha yomsindo erekhodiweyo kwiiseshoni zangaphambili eziye zalahlwa. Olu lwazi "longezelelweyo" lunokususwa ngokulula kwisoftware yokuhlela yasemva kwemveliso ngexesha elizayo.

ISilver Cola kwiThumbscrews yoThutho

I-Silver paste isetyenziswa kwimisonto ye-thumbscrew kwiiyunithi ezintsha kumzi-mveliso ukuphucula uqhagamshelo lombane ukusuka kwindawo yebhetri ngendlu kuyo nayiphi na i-DBSM/DBSMD yokuhambisa. Oku kusebenza kucango lwebhetri esemgangathweni kunye nesicoci sebhetri.

I-vial encinci evalelweyo iqulethe ixabiso elincinci (i-25 mg) ye-silver conductive paste. I-speck encinci yale ntlama iya kuphucula i-conductivity phakathi kwe-thumbscrew yeplate yesigqubuthelo sebhetri kunye necala le-DBSM / DBSMD.

• Ngophuculo lwe-conductivity (ukumelana okusezantsi) ngaphezulu kwevolthi yebhetritagIyakwazi ukufikelela kunikezelo lwangaphakathi lwamandla olubangela ukuthotywa kwamanzi akhoyo kunye nobomi obude bebhetri. Nangona imali ibonakala incinci kakhulu, yanele iminyaka yokusetyenziswa.
• Enyanisweni, sisiphinda-phinda ngama-25 imali esiyisebenzisa kwizikhonkwane zoobhontsi kumzi-mveliso.
• Ukusebenzisa i-paste yesilivere, okokuqala, susa ngokupheleleyo ipleyiti yokugubungela kwindlu ngokuxhasa i-thumbscrew ngokupheleleyo ngaphandle kwetyala. Sebenzisa ilaphu elicocekileyo, elithambileyo ukucoca imisonto yesikrufu sobhontsi.
• PHAWULA: Sukusebenzisa utywala okanye isicoci solwelo.
• Bamba nje ilaphu elijikeleze imisonto kwaye ujike isikrufu sobhontsi. Hambisa kwindawo entsha kwilaphu kwaye wenze kwakhona. Yenza oku de ilaphu lihlale licocekile. Ngoku, hlambulula iintambo kwimeko ngokusebenzisa i-cotton swab eyomileyo (i-Q-tip) okanye ilingana. Kwakhona, coca imisonto yetyala de icotton swab entsha iphume icocekile.
• Vula i-vial, kwaye udlulisele i-pinhead speck ye-spit yesilivere kwintambo yesibini ukusuka ekupheleni kwe-screw-screw. Indlela elula yokucholachola intwana yokuncamathelisa kukutyhila ikliphu yephepha kwaye usebenzise isiphelo socingo ukufumana intwana yokuncamathelisa. I-toothpick nayo iya kusebenza. Isixa esivala isiphelo socingo sanele.
• Akuyomfuneko ukuba usasaze i-paste ngaphezu kwentwana encinci kwintambo njengoko i-paste iya kuzisasaza ngalo lonke ixesha i-thumbscrew is screwed in and out of the case ngexesha lokutshintsha kwebhetri.
• Musa ukufaka intlama kuyo nayiphi na enye indawo. Ipleyiti yokugquma ngokwayo inokucocwa ngelaphu elicocekileyo ngokukhuhla amakhonkco anyuswe kancinci kwipleyiti apho idibana netheminali yebhetri. Ekuphela kwento ofuna ukuyenza kukususa naziphi na ioyile okanye ubumdaka kwizangqa. Musa ukukrazula le miphezulu ngezinto ezibukhali ezifana ne-eraser yepensile, iphepha le-emery, njl., njengoko oku kuya kususa i-nickel plating ye-condutive kwaye iveze i-aluminium engaphantsi, engumqhubi woqhagamshelwano olubi.

I-Antenna ye-Whip ethe ngqo

Ii-antenna zibonelelwa ngumzi-mveliso ngokwale theyibhile ilandelayo:

IBANDLA	IINTLOKO EZIgqunyiweyo	I-ANTENNA ENIKEZELWE
A1	470, 19, 20	I-AMM19
B1	21, 22, 23	I-AMM22
C1	24, 25, 26	I-AMM25

Iicaps ezinikezelweyo zinokusetyenziswa ngeendlela ezininzi ezahlukeneyo:

1. Ikepusi yombala ekupheleni kwesabhokhwe
2. Umkhono wombala ecaleni kwesiqhagamshelo esinekepusi emnyama ekupheleni kwesabhokhwe (nciphisa isiphelo esivaliweyo sekepusi enemibala ngesikere ukwenza umkhono).
3. Umkhono wombala kunye nombala we-cap (unqumle i-cap ngesiqingatha kunye nesikere).

Le template epheleleyo yokusika isetyenziselwa ukusika ubude besabhokhwe kwi-frequency ethile. Beka i-eriyali engasikwanga phezu kwalo mzobo kwaye unciphise ubude besabhokhwe ukuya kumaza okufunayo. Emva kokusika i-eriyali kubude obufunekayo, phawula i-eriyali ngokufaka i-cap yombala okanye umkhono ukubonisa ukuphindaphinda. Iilebhile zasefektri kunye nokumakishwa zidweliswe kwitheyibhile engezantsi.

Phawula: Jonga isikali soshicilelo lwakho. Lo mgca kufuneka ube yi-6.00 intshi ubude (152.4 mm).

Ukumakishwa kweFactory kunye nokuFakwa kweeleyibhile

VIMBA	UHLELO LOKUQHUBEKA	UMBALA WE-CAP/SLEEVE	UBUDE BE-ANTENNA
470	470.100 – 495.600	Mnyama w/ Ileyibhile	5.67 ngaphakathi./144.00 mm.
19	486.400 – 511.900	Mnyama w/ Ileyibhile	5.23 ngaphakathi./132.80 mm.
20	512.000 – 537.575	Mnyama w/ Ileyibhile	4.98 ngaphakathi./126.50 mm.
21	537.600 – 563.100	Brown w/ Ileyibhile	4.74 ngaphakathi./120.40 mm.
22	563.200 – 588.700	Ebomvu w/ Ileyibhile	4.48 ngaphakathi./113.80 mm.
23	588.800 – 607.950	I-Orenji w/ Ileyibhile	4.24 ngaphakathi./107.70 mm.
24	614.400 – 639.900	Yellow w/ Ileyibhile	4.01 ngaphakathi./101.85 mm.
25	640.000 – 665.500	Luhlaza w/ Ileyibhile	3.81 ngaphakathi./96.77 mm.
26	665.600 – 691.100	Blue w/ Ileyibhile	3.62 ngaphakathi./91.94 mm.

Iiseli ezinomthunzi zii-eriyali ezibonelelwa ngefektri

PHAWULA:
Ayizizo zonke iimveliso zeLectrosonics ezakhiwe kuzo zonke iibhloko ezigqunywe kule theyibhile. Ii-eriyali ezibonelelwe ngumzi-mveliso wangaphambili ukuya kubude zibandakanya ilebhile enoluhlu lwamaza.

Iikliphu zebhanti kunye neePoutshi

Ubonelelo lwezixhobo

Izincedisi ozikhethayo

PHAWULA:
Nangona iipowutshi zeleatherette kunye neekliphu zebhanti zocingo zibandakanyiwe neyunithi yakho yokuqala, iipowutshi ezongezelelweyo okanye iikliphu zinokuodolwa kusetyenziswa inombolo efanayo eboniswe kwelinye iphepha.

LectroRM

NgeNew Endian LLC

• I-LectroRM sisicelo esiphathwayo se-iOS kunye ne-Android yokusebenza kwe-smartphone. Injongo yalo kukwenza utshintsho kwiisetingi kwii-transmitter ezikhethiweyo zeLectrosonics ngokuhambisa iithoni zomsindo ezifakwe kwi-microphone eqhotyoshelwe kumthumeli. Xa ithowuni ingena kwi-transmitter, iyanqunyulwa ukuba yenze utshintsho kwiisethingi ezahlukeneyo ezifana nokuzuza igalelo, ukuphindaphinda, kunye nenani lezinye.
• I-app ikhutshwe yi-New Endian, LLC ngoSeptemba 2011. Iyafumaneka ukukhuphela (ihlanganiswe ne-PDR Remote) kwaye ithengisa malunga ne-$ 25 kwi-Apple App Store kunye ne-Google Play Store.
• Iisetingi kunye namaxabiso anokutshintshwa ahluka ukusuka kwimodeli yesidlulisi ukuya kwenye. Uluhlu olupheleleyo lweethowuni ezikhoyo kwi-app lulandelayo:
  • Ingeniso yegalelo
  • Ukuphindaphinda
  • Imo yokuLala
  • Iphaneli TSHIXA/UKUVULA
  • Amandla emveliso yeRF
  • Ukukhutshwa kwezandi ezisezantsi
  • Ii-LEDs ON / OFF

Ujongano lomsebenzisi lubandakanya ukukhetha ulandelelwano lweaudio olunxulumene notshintsho olufunwayo. Uguqulelo ngalunye lunojongano lokukhetha isicwangciso esifunwayo kunye nokhetho olufunwayo kolo seto. Inguqulelo nganye inesixhobo sokuthintela ukusebenza ngempazamo kwethoni.

iOS

Uguqulelo lwe-iPhone lugcina useto ngalunye olukhoyo kwiphepha elahlukileyo kunye noluhlu lokhetho lolo seto. Kwi-iOS, iqhosha lokuguqula "Vumela" kufuneka livulwe ukuze libonise iqhosha eliya kuthi emva koko livule ithowuni. Inguqulelo ye-iOS ehlala iqhelekile ijongiswe phezulu-ezantsi kodwa inokumiselwa ukujongisa kwicala lasekunene phezulu. Injongo yoku kukuqhelanisa isithethi sefowuni, esisezantsi kwesixhobo, kufutshane ne-microphone yokudlulisa.

Android

Inguqulelo ye-Android igcina zonke iisetingi kwiphepha elifanayo kwaye ivumela umsebenzisi ukuba aguqule phakathi kwamaqhosha okuvula kwisetingi nganye. Iqhosha lokuvula kufuneka licinezelwe kwaye libanjwe ukuze ithoni isebenze. Uguqulelo lwe-Android lukwavumela abasebenzisi ukuba bagcine uluhlu olulungisekayo lweeseti ezipheleleyo zesetingi.

Ukuqaliswa
Ukuze isidluliseli siphendule kwiithowuni zeaudio zolawulo olukude, umthumeli kufuneka ahlangabezane neemfuno ezithile:

• Isidluliseli kufuneka sivulwe.
• Umthumeli kufuneka abe noguqulelo lwe-firmware 1.5 okanye kamva kwi-Audio, iFrequency, Lala, kunye noTshixo utshintsho.
• Imakrofoni yothumelo kufuneka ibe phakathi koluhlu.
• Umsebenzi wokulawula kude kufuneka uvulwe kwi-transmitter.

PDRRemote
Ulawulo olukude olufanelekileyo lomsebenzi wokurekhoda we-DBSM unikezelwa yi-app yefowuni (ehlanganiswe ne-LectroRM) ekhoyo kwi-AppStore kunye ne-Google Play. Usetyenziso lusebenzisa iithowuni zeaudio (“iithowuni ze-tweedle”) ezidlalwa kwisithethi sefowuni esitolikwa sisirekhoda ukwenza utshintsho kwisethingi yoshicilelo:

• Record Qala/Yeka
• Inqanaba lokuzuza kweMic
• Tshixa/Vula

Iithoni ze-MTCR zizodwa kwi-MTCR kwaye aziyi kusabela "kwiitoni ze-tweedle" ezijoliswe kwii-transmitters ze-Lectrosonics. Izikrini zivela ngokwahlukileyo kwi-iOS kunye neefowuni ze-Android kodwa zenza imisebenzi efanayo.

Ngeziphumo eziBalaseleyo
Le miqathango ilandelayo iyafuneka:

• I-microphone kufuneka ibe phakathi koluhlu.
• Irekhoda kufuneka iqwalaselwe ukwenza ukuba kusebenze ulawulo olude. Jonga iRemote kwimenyu.

iOS Version

Android Version

• Nceda uqaphele ukuba ezi apps azizomveliso zeLectrosonics.
• I-LectroRM kunye ne-PDRRemote zezabucala kwaye ziqhutywa yiNew Endian LLC, www.newendian.com.
• Jonga kubo webindawo yezibonelelo ezongezelelweyo zobugcisa kunye nenkxaso.

Iinkcukacha

Iifrikhwensi zokusebenza:

• I-DBSM(D)-A1B1: Ibhendi A1-B1: 470.100 – 607.950
• I-DBSM(D)/E01-A1B1: Ibhendi A1-B1: 470.100 – 614.375
• I-DBSM(D)/E01-B1C1: Ibhendi B1-C1: 537.600 - 691.175
• I-DBSM (D)/E09-A1B1 Ibhendi A1-B1: 470.100 – 614-375
• I-DBSMD (D)/E09-A1B1 Ibhendi A1-B1: 470.100 – 614-375

PHAWULA:
Luxanduva lomsebenzisi ukukhetha iifrikhwensi ezivunyiweyo zommandla apho isidluliseli sisebenza khona

• ISithuba seSitishi: 25 kHz
• Iziphumo zeRF Power:
  • I-DBSM: 2 (HDM kuphela), 10, 25 okanye 50 mW
  • DBSMD: 2 (HDM kuphela), 10, 25 okanye 50 mW
  • I-DBSM(D)/E01-A1B1: 2 (HDM kuphela), 10, 25 okanye 50 mW
  • DBSMD(D)/E01-B1C1: 2 (HDM kuphela), 10, 25 okanye 50mW
  • DBSM/E09-A1B1: 2 (HDM kuphela), 10, 25 mW
  • DBSMD/E09-A1B1: 2 (HDM kuphela), 10, 25 mW
• Iindlela ezihambelanayo: DBSM/DBSMD: D2 yedijithali enoguqulelo oluntsonkothileyo, kunye neHDM enoxinaniso oluphezulu lwedijithali olunoguqulelo oluntsonkothileyo.
• Uhlobo lokuModyuli: 8 PSK
• Uhlobo lofihlo: AES-256 kwimo yeCTR
• Uzinzo rhoqo: ± 0.002%
• Imitha yeSpurious: Ihambelana ne-ETSI EN 300 422-1
• Ingxolo yegalelo elilinganayo: -125 dBV, A-weighted
• Inqanaba legalelo:
  • Ukuba imiselwe imakrofoni eguquguqukayo: 0.5 mV ukuya ku-50 mV phambi kokunciphisa uMkhulu kuno-1 V ngokunciphisa
  • Ukuba imiselwe i-electret lavaliere mic: 1.7A ukuya kwi-170 uA phambi kokunciphisa uMkhulu kuno-5000 uA (5 mA) ngokunciphisa
  • Igalelo lenqanaba lomgca: 17 mV ukuya kwi-1.7 V phambi kokunciphisa uMkhulu kune-50 V ngokunciphisa
• Igalelo lokungena:
  • Imakrofoni eyomeleleyo: 300 Ohms
  • I-Electret lavaliere: Igalelo ngumhlaba wenyani kunye ne-servo ehlengahlengisiweyo rhoqo
  • Inqanaba lomgca: 2.7 k ohms
• Isithinteli segalelo: Isithinteli esithambileyo, uluhlu lwe-30 dB
• Umkhethe voltages: Fixed 5 V ukuya kuthi ga kwi-5 mA
  Selectable 2 V okanye 4 V servo bias nayiphi electret lavaliere
• Ukufumana uluhlu lokulawula: -7 ukuya kwi-44 dB; iiswitshi ze-membrane ezifakwe kwiphaneli
• Iimpawu zokumodareyitha: Ii-LED eziphindwe kabini zibonisa ukumodareyitha -20, -10, 0, +10 dB ebhekiselele ekumodareyitheni ngokupheleleyo.
• Ulawulo: Iphaneli yokulawula w / LCD kunye ne-4 inwebu yokutshintsha
• I-low-frequency roll-off: i-Adjustable ukusuka kwi-20 ukuya kwi-150 Hz
• Uhlobo lwegalelo: I-analog mic/line level iyahambelana; i-servo bias ngaphambiliamp kuba 2V kunye 4V Lavaliere microphone
• Inqanaba legalelo:
  • Imakrofoni eDynamic: 0.5 mV ukuya ku-50 mV
  • I-Electret mic: Igama le-2 mV ukuya kwi-300 mV
  • Inqanaba lomgca: 17 mV ukuya ku-1.7 V
• Isidibanisi segalelo: TA5M 5-pin eyindoda
• Ukusebenza komsindo
  • Ukuphendula rhoqo: 20Hz ukuya ku-20kHz, +/- 1dB: Imowudi ye-D2 20Hz ukuya kwi-16KHz, +/- 3dB: Indlela Yoxinano Oluphezulu (HDM)
  • Uluhlu olunamandla: 112 dB (A)
  • Ukuphazamiseka: <0.035%
• I-antenna: Intambo yentsimbi ethambileyo, engenakwaphuka.
• Ibhetri: AA (+1.5 VDC), ilahlwa, iLithium iyacetyiswa

	Lithium	Ialkaline	NiMH
I-DBSM-A1B1 (1 AA):	2 mv – 8:55 10 mv – 7:25 25 mv – 6:35 50 mv – 4:45	2 mv – 2:15 10 mv – 2:00 25 mv – 1:25 50 mv – 1:10	2 mv – 5:25 10 mv – 4:55 25 mv – 4:25 50 mv – 4:20
I-DBSMD-A1B1 (2 AA):	2 mv – 18:20 10 mv – 16:35 25 mv – 15:10 50 mv – 12:10	2 mv – 7:45 10 mv – 7:10 25 mv – 6:20 50 mv – 4:30	2 mv – 10:55 10 mv – 10:30 25 mv – 9:20 50 mv – 7:25

• Ubunzima w/ibhetri:
  • I-DBSM-A1B1: 3.2 oz. (90.719 grams)
  • I-DBSMD-A1B1: 4.8 oz. (136.078 grams)
• Imilinganiselo iyonke:
  • I-DBSM-A1B1: 2.366 x 1.954 x 0.642 intshi; (ngaphandle kombhobho) 60.096 x 49.632 x 16.307 mm
  • I-DBSMD-A1B1: 2.366 x 2.475 x 0.642 intshi; 60.096 x 62.865 x 16.307 mm
• Umyili wokuPhuma:
  • DBSM-A1B1/DBSMD-A1B1: 170KG1E (D2 mode)
  • I-DBSM-A1B1/DBSMD-A1B1: 110KG1E (imowudi yeHD)

Umshicileli

• Imidiya yokugcina: imemori khadi ye-microSDHC
• File ifomathi: .wav files (BWF)
• A/D converter: 24-bit
• Sampisantya sokulala: 48 kHz
• Iimowudi zokurekhoda/Isantya seBit:
  • Imowudi ye-HD ye-mono: i-24 bit - 144 kbytes / s

Igalelo

• Uhlobo: I-analog mic/line level iyahambelana; i-servo bias ngaphambiliamp kuba 2V kunye 4V Lavaliere microphone
• Inqanaba legalelo:
  • Imakrofoni eDynamic: 0.5 mV ukuya ku-50 mV
  • I-Electret mic: Igama le-2 mV ukuya kwi-300 mV
  • Inqanaba lomgca: 17 mV ukuya ku-1.7 V
• Isidibanisi segalelo: TA5M 5-pin eyindoda
• Ukusebenza komsindo
  • Ukuphendula rhoqo: 20Hz ukuya ku-20kHz, +/- 1dB:
  • Uluhlu olunamandla: 112 dB (A)
  • Ukuphazamiseka: <0.035%
• Uluhlu lobushushu obusebenzayo
  • Celsius: -20 ukuya kuma-50
  • IFahrenheit: -5 ukuya kwi-122

Iinkcukacha zinokutshintshwa ngaphandle kwesaziso.

Ixesha elifumanekayo lokuRekhoda
Ukusebenzisa i-microSDHC* yememori khadi, uqikelelo lwamaxesha okurekhoda anje. Ixesha elililo lingohluka kancinci kumaxabiso adweliswe kwiitheyibhile.

(imowudi ye-HD mono)

Ubungakanani	Hrs:Mz
8GB	11:10
16GB	23:00
32GB	46:10

Ukulungisa ingxaki

Isilumkiso sekhadi elicothayo ngexa urekhoda 

1. Le mpazamo ilumkisa umsebenzisi kwinto yokuba ikhadi alikwazi ukugcina kunye nesantya apho i-DBSM irekhoda idatha.
2. Oku kudala izithuba ezincinci kushicilelo.
3. Oku kunokubonisa umba xa ushicilelo luza kulungelelaniswa nenye iaudio okanye ividiyo.

Inkonzo kunye noLungiso

Ukuba isixokelelwano sakho asisebenzi, kufuneka uzame ukulungisa okanye ukwahlukanisa ingxaki phambi kokuba ugqibe kwelokuba isixhobo sifuna ukulungiswa. Qinisekisa ukuba uyilandele inkqubo yokuseta kunye nemiyalelo yokusebenza. Jonga iintambo eziqhagamshelayo kwaye emva koko uye ngapha kweCandelo leNgxaki kule ncwadana.

Sincoma kakhulu ukuba ungazami ukulungisa izixhobo ngokwakho kwaye ungabi nevenkile yokulungisa yasekuhlaleni ukuzama nantoni na ngaphandle kokulungiswa okulula. Ukuba ukulungiswa kuyinkimbinkimbi kunocingo oluphukileyo okanye uxhulumaniso olukhululekile, thumela iyunithi kwifektri ukulungiswa kunye nenkonzo. Musa ukuzama ukulungisa naluphi na ulawulo ngaphakathi kwiiyunithi. Nje ukuba isetiwe kumzi-mveliso, ulawulo olwahlukeneyo kunye nezilungisi azikhukuli ngokuguga okanye ukungcangcazela kwaye azize zifune ukulungiswa kwakhona. Akukho luhlengahlengiso ngaphakathi oluya kwenza iyunithi engasebenzi kakuhle iqale ukusebenza.

Isebe leNkonzo le-LECTROSONICS lixhotyisiwe kwaye linabasebenzi ukuze balungise ngokukhawuleza izixhobo zakho. Kwiwaranti, ukulungiswa kwenziwa ngaphandle kwentlawulo ngokwemiqathango yewaranti. Ulungiso olungaphandle kwewaranti luhlawuliswa ngexabiso eliphantsi elicaba kunye neenxalenye kunye nokuthunyelwa. Ekubeni kuthatha phantse ixesha elininzi kunye nomgudu ukumisela ukuba yintoni engalunganga njengoko isenza ukulungisa, kukho intlawulo yekowuteshini ngqo. Siya kukuvuyela ukucaphula iintlawulo eziqikelelweyo ngefowuni zolungiso olungaphandle kwewaranti.

IiYunithi eziBuyisayo zokuLungisa
Ngenkonzo yangexesha, nceda ulandele la manyathelo angezantsi:

• MUSA ukubuyisela izixhobo kumzi-mveliso ukuze zilungiswe ngaphandle kokuqala uqhagamshelane nathi nge-imeyile okanye ngefowuni. Kufuneka sazi uhlobo lwengxaki, inombolo yemodeli, kunye nenombolo yesiriyali yesixhobo. Siphinde sifune inombolo yefowuni apho unokufikelelwa khona ngo-8 AM ukuya ku-4 PM (Ixesha le-Mountain Standard yase-US).
• Emva kokufumana isicelo sakho, siya kukunika inombolo yogunyaziso lokubuyisela (RA). Le nombolo iya kunceda ukukhawulezisa ukulungiswa kwakho ngamasebe ethu okufumana kunye nokulungisa. Inombolo yogunyaziso lokubuyisela kufuneka iboniswe ngokucacileyo ngaphandle kwesingxobo sokuthumela.
• Pakisha izixhobo ngononophelo kwaye uzithumele kuthi, iindleko zokuthumela zihlawulwa kwangaphambili. Ukuba kuyimfuneko, sinokukubonelela ngezinto ezifanelekileyo zokupakisha. I-UPS idla ngokuba yeyona ndlela ilungileyo yokuthumela iiyunithi. Iiyunithi ezinzima kufuneka "zifakwe kabini" kuthutho olukhuselekileyo.
• Sikwacebisa ngamandla ukuba ukhusele izixhobo, kuba asinakuba noxanduva lokulahleka okanye ukonakala kwezixhobo ozithumelayo. Ewe kunjalo, siqinisekisa izixhobo xa sizithumela kuwe.

Lectrosonics USA:

• Idilesi yemeyile: Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA
• Web: www.lectrosonics.com

Lectrosonics eKhanada:

• Idilise yemeyile:
  720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9
• Idilesi yokuyithumela ngenqanawe:
  Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA
• I-imeyile:
  sales@lectrosonics.com
• Umnxeba:
  • 416-596-2202
  • 877-753-2876 Itholi yasimahla
  • (877-7LECTRO)
  • 416-596-6648 Ifeksi
• Umnxeba:
  • 505-892-4501
  • 800-821-1121 Itholi yasimahla
  • 505-892-6243 Ifeksi
• I-imeyile:
  • Intengiso: colinb@lectrosonics.com
  • Inkonzo: joeb@lectrosonics.com.

Ukhetho lokuzinceda kwiiNgxaki eziNgangxamisekanga
Amaqela ethu Facebook kunye web uluhlu lubutyebi bolwazi lwemibuzo yabasebenzisi kunye nolwazi. Ibhekisele ku:

• Lectrosonics General Facebook Group: https://www.facebook.com/groups/69511015699
• D Isikwere, iNdawo yesi-2 kunye neQela loMyili ongenazingcingo: https://www.facebook.com/groups/104052953321109
• Uluhlu lweeNcingo: https://lectrosonics.com/the-wire-lists.html.

Kumsebenzi onxitywe umzimba, le modeli yesithutha iye yavavanywa kwaye iyahlangabezana nezikhokelo zokuvezwa kweFCC RF xa isetyenziswa kunye nezincedisi zeLectrosonics ezibonelelweyo okanye ezilungiselelwe le mveliso. Ukusetyenziswa kwezinye izincedisi akunakuqinisekisa ukuthotyelwa kwezikhokelo zokuvezwa kweFCC RF. Qhagamshelana neLectrosonics ukuba unayo nayiphi na imibuzo okanye ufuna ulwazi oluthe kratya malunga nokuba sesichengeni seRF usebenzisa le mveliso. Esi sixhobo sithobela imida ye-FCC yokuvezwa kwemitha njengoko imiselwe indawo engalawulwayo. Esi sixhobo kufuneka sifakwe kwaye sisebenze ukuze i(ii)eriyali zaso zingahlali kunye okanye zisebenze kunye nayo nayiphi na enye i-eriyali okanye isidluliseli.

Izaziso ze-ISEDC:

Ngokwe-RSS-210
Esi sixhobo sisebenza kwisiseko sokungakhuseli ngaphandle kokuphazamiseka. Ukuba umsebenzisi ufuna ukufumana ukhuseleko kwezinye iinkonzo zikanomathotholo ezisebenza kwamaqela eTV afanayo, kufuneka ilayisensi yerediyo. Nceda ujonge uxwebhu lwe-Industry Canada lwe-CPC-2-1-28, iLayisensi eKhethekileyo ye-Low-Power Radio Apparatus kwiibhendi zeTV, ngeenkcukacha.

Ngokwe-RSS-Gen
Esi sixhobo sithobelana ne-RSS ye-Industry Canada's license-exept. Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:

1. Esi sixhobo sisenokungabangeli ukuphazamiseka
2. Esi sixhobo kufuneka samkele naluphi na uphazamiseko, kuquka uphazamiseko olunokubangela ukusebenza okungafunekiyo kwesixhobo.

IWARANTI YONYAKA OMNYE

Isixhobo sigunyaziswa unyaka omnye ukususela kumhla wokuthengwa kweziphene kwimathiriyeli okanye ekusetyenzweni kwayo ngaphandle kokuba sithengwe kumthengisi ogunyazisiweyo. Esi siqinisekiso asiyifaki izixhobo eziye zaxhatshazwa okanye zonakaliswe kukuphathwa ngokungakhathali okanye ukuthunyelwa ngenqanawa. Esi siqinisekiso asisebenzi kwizixhobo ezisetyenzisiweyo okanye zokubonisa.

Ukuba kukho nasiphi na isiphene, iLectrosonics, Inc. iya kuthi, ngokokhetho lwethu, ilungise okanye ibuyisele naziphi na iindawo ezineziphene ngaphandle kwentlawulo nangayiphi na indawo okanye abasebenzi. Ukuba iLectrosonics, Inc. ayikwazi ukulungisa isiphene kwisixhobo sakho, iya kutshintshwa ngaphandle kwentlawulo ngento entsha efanayo. I-Lectrosonics, Inc. iya kuhlawulela iindleko zokubuyisela izixhobo zakho kuwe. Esi siqinisekiso sisebenza kuphela kwizinto ezibuyiselwe kwi-Lectrosonics, Inc. okanye kumthengisi ogunyazisiweyo, iindleko zokuthumela ngenqanawa zihlawulwe kwangaphambili, kwisithuba sonyaka omnye ukususela kumhla wokuthenga.

Esi siqinisekiso siMnyino silawulwa yimithetho yeLizwe laseNew Mexico. Ichaza lonke uxanduva lweLectrosonics Inc. kunye nesisombululo esipheleleyo somthengi kuko nakuphi na ukwaphulwa kwewaranti njengoko kuchaziwe ngasentla. I-LECTROSONICS, INC. NANANI NA NOBANDAKANYEKA EKUVELISWA OKANYE EKUBONELWENI KWESIXHOBO UYA KUTHWALAPHA UBUCHULEKO LWESIXHOBO, ESIKHETHEKILEYO, ESISOHLWAYO, ESIPHUMELELEYO, OKANYE UMONAKALO OSETHULWEYO OVELA OKU, OKANYE KUNGAFANELEKANGA. UCEBISIWE NGOKUBA OKUNGENZEKA UMONAKALO OLULO. AKUKHO MFANEKO AYIKHO UXANDUVA LWE-LECTROSONICS, INC.

Esi siqinisekiso sikunika amalungelo athile asemthethweni. Usenokuba namalungelo asemthethweni awongezelelweyo ahluka ngokwelizwe ukuya kwelinye.

• 581 Laser Road NE • Rio Rancho, NM 87124 USA
• www.lectrosonics.com
• 505-892-4501
• 800-821-1121
• ifeksi 505-892-6243
• sales@lectrosonics.com.

Amaxwebhu / Izibonelelo

I-LECTROSONICS DBSM-A1B1 iTranskoda yeDijithali [pdf] Incwadi Yomyalelo I-DBSM-A1B1, i-DBSM-E01-A1B1, i-DBSM-E01-B1C1, i-DBSMD-A1B1, i-DBSMD-E01-A1B1, i-DBSMD-E01-B1C1, i-DBSM-E09-A1B1, i-DBSMD-E09-DSMgi-Transfer1B1, I-DBSM-A1B1, i-Digital Transcorde, iTranscorder

Iimbekiselo

• Incwadi yokusebenzisa