LECTROSONICS DBSM-A1B1 Digital Transcorder

Product Information

• Muenzaniso: DBSM/DBSMD Digital Transcorder
• Frequency Range: 470.100 kusvika 607.950 MHz (DBSM/DBSMD/E01 frequency range iri 470.100 kusvika 614.375 MHz)
• Output Power: Inosarudzwa 10, 25, kana 50 mW
• Transmission Mode: High-density mode pa 2 mW
• Kunobva Simba: Mabhatiri maviri AA
• Inzwa Zvinotaurwa Jack: Standard Lectrosonics 5-pini yekupinda jack
• Antenna Port: 50 ohm SMA connector

Mirayiridzo Yekushandiswa Kwechigadzirwa

• Overview
  Iyo DBSM/DBSMD transmitter yakagadzirirwa kushanda kwakanyanya uye yakawedzerwa nguva yekushandisa. Inoshanda pane iyo UHF terevhizheni bhendi ine inosarudzwa inobuda magetsi sarudzo.
• Powering On
  Isa maviri AA mabhatiri mune inotumira. Ita shuwa kuti mabhatiri akaiswa zvakanaka aine polarity chaiyo. Dzvanya bhatani remagetsi kuti ubatidze transmitter.
• Frequency Tuning
  Shandisa tuning controls kuti usarudze frequency yaunoda mukati meiyo inotsigirwa renji. Ita shuwa kuti iyo transmitter frequency inoenderana neanogamuchira frequency yekutaurirana kwakaringana.
• Input Connection
  Batanidza maikorofoni yako kana odhiyo sosi kune yakajairwa Lectrosonics 5-pini yekuisa jack pane transmitter. Shandisa tambo dzakakodzera uye zvibatanidza zvekubatanidza kwakachengeteka.
• Level Settings
  Rongedza mazinga ekuteerera uchishandisa keypad maLED ekukurumidza uye kwakaringana marongero. Tarisa mazinga kudzivirira kukanganisa kana kutema odhiyo.
• Kurekodha Basa
  Iyo transmitter ine yakavakirwa-mukati yekurekodha basa rekushandisa yakamira kana mamiriro apo RF kutapurirana kusingagoneke. Rangarira kuti kurekodha uye kutumira hakugone kuitwa panguva imwe chete.
• Kutsiviwa kwebhatiri
  Tarisa mamiriro ebhatiri nguva nenguva. Kana mabhatiri ari mashoma, chinja iwo neatsva AA mabhatiri kuti uve nechokwadi chekushanda kusina kukanganiswa.

Mibvunzo Inowanzo bvunzwa

Mubvunzo: Ndinogona here kushandisa asiri-Lectrosonics maikorofoni ine transmitter?

A: Ehe, unogona kumisa asiri-Lectrosonics maikorofoni uchishandisa yakakodzera tambo kumiswa. Tarisa kune bhuku remushandisi kune yakadzama mirairo pane wiring magadzirirwo.

Mubvunzo: Chii chinangwa cheDSP-inodzorwa Input Limit?

A: Iyo DSP-inodzorwa Input Limit inobatsira kudzivirira kukanganiswa kweodhiyo nekudzikamisa mazinga ekuisa mukati meyakachengeteka renji, kuve nechokwadi chekufambisa odhiyo kwakajeka.

Mubvunzo: Ndinoziva sei nguva yekutsiva mabhatiri?

A: Ramba wakatarisa pane chiratidzo chebhatiri. Kana iyo chiratidzo ichiratidza yakaderera bhatiri mwero, chinja mabhatiri nekukasira kudzivirira kukanganisa mukushanda.

Nhanganyaya

Iyo DBSM/DBSMD transmitter inoshandisa yakakwirira-inoshanda dhijitari yedhijitari kwenguva yakawedzerwa yekushandisa pamabhatiri maviri eAA. Iyo transmitter inogona kuridza nhanho mhiri kweiyo UHF terevhizheni bhendi kubva pa470.100 kusvika 607.950 MHz.
(DBSM/DBSMD/E01 frequency range ndeye 470.100 kusvika 614.375 MHz), ine simba rinosarudzwa rinobuda re10, 25, kana 50 mW. Iyo yakakwirira-density transmission mode pa 2 mW inobvumira padhuze mutakuri spacing kune yakanyanya chiteshi mukati mehuwandu hwakapihwa.

Iyo yakachena yedhijitari dhizaini inogonesa AES 256 encryption kune yakakwirira-level kuchengetedza maapplication. Studio yemhando yekuteerera inovimbiswa nepamusoro-mhando zvikamu mupreamp, yakafara siyana yekupinza kuwana kugadzirisa, uye DSP-inodzorwa kudzikisira. Input yekubatanidza uye zvigadziriso zvinosanganisirwa kune chero maikorofoni yeLavaliere, maikorofoni ane simba, uye mutsara-chikamu chekuisa. Kupinza kuwana kunogadziriswa pamusoro pe44 dB renji mumatanho e1 dB kubvumira mutambo chaiwo kune iyo yekuisa chiratidzo nhanho, kukwirisa iyo ine simba renji uye chiratidzo-ku-ruzha reshiyo.

Imba iyi ishongwe, yakagadzirwa nealuminium pasuru ine yakajairwa Lectrosonics 5-pini yekupinza jack yekushandisa ine electret lavaliere mics, dynamic mics, mimhanzi chiridzwa pickups, uye mutsara-level masaini. Iwo ma LED pane keypad anobvumira nekukurumidza uye kwakaringana nhanho marongero pasina kuita view mugamuchiri. Iyo unit inofambiswa neAA batter-ies, uye antenna port inoshandisa yakajairwa 50 ohm SMA yekubatanidza.
Kuchinja magetsi kunopa nguva dzose voltages kumaseketi ekutapurirana kubva pakutanga kusvika kumagumo ehupenyu hwebhatiri, nesimba rekubuda richiramba riripo pamusoro pehupenyu hwebhatiri.

Servo Bias Input uye Wiring
The input preamp dhizaini yakasarudzika inoburitsa zvinonzwika kuvandudzwa pamusoro pezvakajairwa transmitter zvinopinza. Zvirongwa zviviri zvakasiyana maikorofoni wiring zviripo kuti zvirerutsa uye kuenzanisa gadziriso. Yakarerutswa 2-waya uye 3-waya zvigadziriso zvinopa akati wandei marongero akagadzirirwa kushandiswa chete ne servo bias yekupinda kutora yakazara advan.tage zve preamp circuitry. Iyo mutsara-level yekuisa wiring inopa yakawedzera frequency mhinduro neLF roll-off pa20 Hz yekushandisa nezviridzwa uye mutsara-chikamu chechiratidzo masosi.

DSP-inodzorwa Input Limiter
Iyo transmitter inoshandisa inodzorwa nedhijitari analog audio limiter pamberi peanalog-to-digital converter. Iyo limiter ine huwandu hwakakura kupfuura 30 dB yekudzivirira kwakanyanya kuwanda. Emvuropu inoburitsa mbiri inoita kuti chinomisikidza chive pachena uku uchichengetedza kukanganiswa kwakaderera. Inogona kufungidzirwa semiganho miviri munhevedzano, yakabatana sekukurumidza kurwisa uye kuburitsa limiter inoteverwa neanononoka kurwisa uye kuburitsa limiter. Iyo limiter inopora nekukurumidza kubva kune pfupi pfupi, kuitira kuti chiito chayo chivanzike kubva kune anoteerera, asi inopora zvishoma nezvishoma kubva kune yakasimudzwa mazinga kuti ichengetedze kukanganiswa kweodhiyo kwakadzikira uye kuchengetedza shanduko yenguva pfupi yekuchinja muodhiyo.

Recorder basa
Iyo DBSM/DBSMD ine yakavakirwa-mukati kurekodha basa rekushandisa mumamiriro ezvinhu apo RF ingasagoneke kana kushanda seyakamira-yega rekodha. Iyo rekodhi basa uye kufambisa mabasa anosarudzika kune mumwe nemumwe - haugone kurekodha UYE kufambisa panguva imwe chete. Kana iyo unit iri kufambisa uye kurekodha ikavhurwa, odhiyo muRF kutapurirana inomira, asi mamiriro ebhatiri acharamba achitumirwa kune anogamuchira. Murekodha sampzvishoma pachiyero che 48 kHz ine 24-bit sample deep. Iyo micro SDHC kadhi inopa zvakare nyore firmware yekuvandudza masimba pasina kudiwa kwe USB tambo kana nyaya dzemutyairi.

Encryption
Pakutumira odhiyo, pane mamiriro ezvinhu apo kuvanzika kwakakosha, senge panguva yemitambo yehunyanzvi, mumatare edzimhosva kana mumisangano yakavanzika. Nezviitiko uko kutumira kwako odhiyo kunofanirwa kuchengetedzwa, pasina kupira mhando yekuteerera, Lectrosonics inoshandisa AES256 encryption mune yedu dijitari isina waya maikorofoni masisitimu. Yakakwira entropy encryption kiyi dzinotanga kugadzirwa neLectrosonics inogamuchira senge DSQD Receiver. Kiyi inozowiriraniswa neDBSM kuburikidza neIR port. Iyo yekufambisa ichave yakavharidzirwa uye inogona chete kudhindwa kana inogamuchira uye mupepeti aine makiyi ekunyorera anoenderana. Kana iwe uri kuyedza kufambisa chiratidzo chekuteerera uye makiyi haaenderane, zvese zvinonzwika kunyarara.

Kuenderana ne microSDHC memori makadhi

• Ndapota cherechedza kuti DBSM/DBSMD yakagadzirirwa kushandiswa ne microSDHC memori makadhi. Kune akati wandei emhando dzeSD kadhi zviyero (sezvekunyora uku) zvichibva pakugona (kuchengeta muGB).
  • SDSC: yakajairika huwandu, kusvika uye kusanganisira 2 GB - USASHANDISE!
  • SDHC: yakakwirira huwandu, inodarika 2 GB uye inosvika uye inosanganisira 32 GB - SHANDISA IYI TYPE.
  • SDXC: yakawedzera huwandu, inopfuura 32 GB uye kusvika uye kusanganisira 2 TB - USASHANDISE!
  • SDUC: yakawedzera huwandu, inopfuura 2TB uye inosvika uye inosanganisira 128 TB - USASHANDISE!
• Iwo makuru eXC neUC makadhi anoshandisa akasiyana fomati nzira uye chimiro chebhazi uye HAZVI enderane nerekodha. Izvi zvinowanzo shandiswa neakazotevera-chizvarwa vhidhiyo masisitimu uye makamera ekushandisa kwemifananidzo (vhidhiyo uye yakakwirira resolution, yakakwirira-kumhanya mafoto).
• CHETE microSDHC memori makadhi anofanira kushandiswa. Iwo anowanikwa mune masimba kubva ku4GB kusvika ku32GB. Tarisa makadhi eClass Class 10 (sezvinoratidzwa neC yakaputirwa nhamba ye10), kana makadhi eUHS Speed ​​Class I (sezvinoratidzwa nenhamba 1 mukati mechiratidzo cheU). Zvakare, cherechedza iyo microSDHC Logo.
• Kana iwe uchichinjira kumhando nyowani kana kunobva kadhi, tinogara tichikurudzira kuyedza tisati tashandisa kadhi pane yakakosha application.
• Mamikira anotevera achaonekwa pamamemory card anowirirana. Imwe kana yese yemakaka ichaonekwa pane kadhi imba uye nekurongedza.

Features

Main Window Indicators
Iyo Main Window inoratidza RF Standby kana Operating (transmitting) mode, kushanda frequency, audio level, uye bhatiri mamiriro.

Battery Status LED Indicator

• AA mabhatiri anogona kushandiswa kusimbisa transmitter.
• Iyo LED yakanyorwa kuti BATT pane keypad inopenya girini kana mabhatiri akanaka. Ruvara rwunoshanduka kuita dzvuku kana bhatiri rakwiratage inodonha pasi uye inoramba yakatsvuka kuburikidza nekwasara kwehupenyu hwebhatiri. Kana iyo LED ikatanga kupenya tsvuku, pachange paine maminetsi mashoma enguva yekumhanya yasara.
• Iyo chaiyo nzvimbo iyo ma LED anotsvuka ichasiyana nebhatiri mhando uye mamiriro, tembiricha, uye mashandisiro emagetsi. Iwo ma LED anoitirwa kungobata kutarisisa kwako, kwete kuti ive chiratidzo chaicho chenguva yasara.
• Bhatiri risina simba dzimwe nguva rinoita kuti LED ivheneke girinhi pakarepo mushure mekunge transmitter yabatidzwa, asi ichakurumidza kubuda kusvika painozotsvuka LED kana unit ichidzima zvachose.
• Mamwe mabhatiri anopa nyevero shoma kana kusatombopa kana apera. Kana iwe uchida kushandisa mabhatiri aya mune transmitter, iwe unozofanirwa kuchengeta iwe pachako nguva yekushandisa uchishandisa inogamuchira bhatiri timer basa kudzivirira kukanganisa kunokonzerwa nemabhatiri akafa.
• Tanga nebhatiri rakazara, wozoyera nguva inotora kuti Simba re LED ribude zvachose.

CHERECHEDZA:
Iyo bhatiri timer inoratidzira mune akawanda Lectrosonics inogamuchira inobatsira zvikuru mukuyera bhatiri kumhanya. Tarisa kune anogamuchira mirairo kuti uwane ruzivo rwekushandisa iyo timer.

Encryption Status LED Indicator Modes 

• StandBy: Iyo yebhuruu LED YAKOMA uye iyo Operating Mode Indicator icon ine mutsara kuburikidza nayo
• Kiyi Inoshaikwa / Yakashata: Bhuruu LED iri FLASHING
• Kutumira: Bhuruu LED inogara iri ON

IR (infrared) Sync
Iyo IR port ndeyekukurumidza kuseta uchishandisa inogamuchira ine basa iri rinowanikwa. IR Sync ichaendesa zvigadziriso zvenguva, nhanho saizi, uye inopindirana modhi kubva kune inogamuchira kuenda kune inotapurirana. Iyi nzira inotangwa nemugamuchiri. Kana iyo sync basa rasarudzwa pane inogamuchira, bata IR chiteshi chemutakuri pedyo neIR port yeanogamuchira. (Hapana chemenu chinhu chinowanikwa pane chinotapurirana kuti utange sync.)

CHERECHEDZA:
Kana kusawirirana kuripo pakati peanogamuchira uye anotumira, meseji yekukanganisa ichaonekwa pane inotumira LCD ichitaura kuti dambudziko chii.

Kuiswa kweBattery

• Iyo transmitter inofambiswa nemabhatiri eAA. Isu tinokurudzira kushandisa lithium kwehupenyu hwakareba.
• Nekuti mamwe mabhatiri anodonha nekukasira, kushandisa iyo Power LED kuratidza mamiriro ebhatiri hakuzovimbike. Nekudaro, zvinokwanisika kuteedzera mamiriro ebhatiri uchishandisa bhatiri timer basa rinowanikwa muLectrosonics vanogamuchira.
• Gonhi rebhatiri rinovhurika nekungosunungura knurled knob partway kusvika gonhi richitenderera. Musuwo unobviswawo nyore nyore nekusunungura knob zvachose, iyo inobatsira pakuchenesa mabhatiri. Mabatiro ebhatiri anogona kucheneswa nedoro uye cot-ton swab, kana penzura yakachena eraser. Iva nechokwadi chekuti usasiya chero zvakasara zvekotoni swab kana eraser crumbs mukati mekamuri.
• Iyo diki pinpoint dab yesirivha conductive girisi pane thumbscrew tambo inogona kunatsiridza mashandiro ebhatiri uye kushanda. Ona peji 22. Ita izvi kana ukaona kuderera kwehupenyu hwebhatiri kana kuwedzera kwemaitiro ekushanda.
• Kana iwe usingakwanise kutsvaga mutengesi werudzi urwu rwegirisi - chitoro chemagetsi chemuno che ex.ample - bata mutengesi wako kana fekitori kuti uwane diki rekugadzirisa vial.
• Isai mabhatiri maererano nemavara kuseri kweimba. Kana mabhatiri akaiswa incor-rectly, gonhi rinogona kuvhara asi chikwata hachizoshanda.

Kubatanidza Signal Source
Maikorofoni, mutsara-nhanho odhiyo masosi, uye zviridzwa zvinogona kushandiswa neinotumira. Tarisa kuchikamu chakanzi Input Jack Wiring for Different Sources kuti uwane ruzivo rweiyo wiring yemutsara-level masosi uye maikorofoni kutora yakazara advan.tage yeServo Bias circuitry.

Kugadzira SD Kadhi

• Nyowani microSDHC memori makadhi anouya akafanofomatidzwa neFAT32 file system iyo inogadziridzwa kuita zvakanaka. Iyo unit inovimba nekuita uku uye haizombokanganisa iyo yakadzika-level fomati yeSD kadhi.
• Kana iyo DBSM/DBSMD "inogadzirisa" kadhi, inoita basa rakafanana neWindows "Quick Format" inobvisa zvese. files uye inogadzirira kadhi rekunyora. Kadhi inogona kuverengwa nekombiyuta chero ipi zvayo asi kana chero kunyora, kugadzirisa, kana kubviswa kuchiitwa kadhi nekombuta, kadhi inofanira kuchinjwa zvakare neDBSM / DBSMD kuti igadzirire zvakare kurekodha. Iyo DBSM/DBSMD haina kumbobvira yakaderera-level mafomati kadhi uye isu tinoraira zvakasimba kusaita kudaro nekombuta.
• Kufometa kadhi neDBSM/DBSMD, sarudza Format Card mumenu wodzvanya MENU/SEL pakiyipadhi.

YAMBIRO:
Usaite yakaderera-level fomati (yakazara-yakazara fomati) nekombuta. Kuita izvi kunogona kuita kuti memori kadhi isashande neDBSM/DBSMD rekodha. Uine Windows-based komputa, ita shuwa kutarisa nekukurumidza fomati bhokisi usati wafomati kadhi. NeMac, sarudza MS-DOS (FAT).

ZVINOKOSHA
Mafomati eiyo SD kadhi inomisikidza zvikamu zvinosangana kuti zvinyatso shanda mukuita kwekurekodha. The file fomati inoshandisa iyo BEXT (Broadcast Extension) wave fomati ine nzvimbo yakakwana yedata mumusoro weiyo file ruzivo uye kodhi yenguva imprint.

• Iyo SD kadhi, seyakarongwa neDBSM/DBSMD rekodhi, inogona kushatiswa nechero kuedza kugadzirisa zvakananga, kushandura, fomati, kana view the files pakombiyuta.
• Nzira iri nyore yekudzivirira huwori hwe data ndeyekukopa iyo .wav files kubva pakadhi kuenda kune komputa kana mamwe maWindows kana OS-yakarongwa midhiya KUTANGA. Dzokorora – COPY THE FILES FIRST!
• Usatumidza zita files zvakananga pane SD kadhi.
• Usaedza kugadzirisa files zvakananga pane SD kadhi.
• Usasevha CHINHU kune SD kadhi nekombuta (senge tora log, cherechedza file,s etc) - yakagadzirirwa kushandiswa kweDBSM rekodhi chete.
• Usavhura iyo files pane SD kadhi ine chero yechitatu-bato chirongwa seWave Agent kana Audacity uye bvumidza kuchengetedza. MuWave Agent, usaite ZVINOKOSHA - unogona KUVURA nekuiridza asi usachengete kana Kupinza - Wave Agent inoshatisa file.
• Muchidimbu - hapafanirwe kuve nekunyengedzwa kweiyo data pakadhi kana kuwedzera kwedata kune kadhi nechero chinhu kunze kweDBSM / DBSMD rekodhi. Copy the files kune komputa, chigunwe chidhiraivha, hard drive, nezvimwe. iyo yakaumbwa seyakajairwa OS mudziyo KUTANGA - wobva wagona kugadzirisa wakasununguka.

iXML HEADER SUPPORT
Zvinyorwa zvine indasitiri-yakajairwa iXML chunks mune file misoro, ine minda inonyanya kushandiswa yakazadzwa.

Kubatidza Simba reTransmitter

Short Bhatani Press
Kana iyo unit yadzimwa, kudzvanya kupfupi kwebhatani remagetsi ichabatidza unit muStandby Mode neRF yakadzimwa. Izvi zvinobatsira pakugadzirisa marongero payuniti pasina kutapurirana.

RF chiratidzo chinobwaira

Long Bhatani Press
Kana iyo unit yadzimwa, kudzvanya kwenguva refu kwebhatani remagetsi kunotanga kuverenga pasi kuti ubatidze iyo unit nekubuda kweRF yakabatidzwa. Ramba wakabata bhatani kusvika kuverenga kwapera.

Kana bhatani rikaburitswa kuverengera kusati kwapera, iyo unit inosimuka neRF yakadzimwa.

Menu Shortcuts
Kubva kuMain/Home Screen, anotevera mapfupi anowanikwa:

• LEDs On: Dzvanya museve weUP
• LEDs Off: Dzvanya iyo PASI museve
• Wana Kugadzika: Kureba dzvanya bhatani reMENU uye bata paunenge uchigadzirisa kuwana kumusoro kana pasi uchishandisa makiyi emiseve
• Rekodha: Dzvanya iyo BACK + UP museve panguva imwe chete
• Mira Kurekodha: Dzvanya iyo BACK + PASI museve panguva imwe chete

CHERECHEDZA:
Mapfupi ekurekodha anongowanikwa kubva kuhombe / imba skrini UYE kana microSDHC memori kadhi yakaiswa.

Powering Off
Kubva pane chero chidzitiro, simba rinogona kudzimwa nekusarudza Pwr Off mumenyu yemagetsi, wakabata Bhatani reSimba mukati uye kumirira bhaa yekufambira mberi, kana neiyo programmable switch (kana yakarongedzerwa basa iri).

Kana bhatani remagetsi rikaburitswa, kana chinja chepaneru chepamusoro chadzoserwa zvakare bhaa rekufamba risati raenderera, unit icharamba yakabatidzwa uye LCD inodzokera kuchiratidziro chimwe chete kana menyu yakamboratidzwa.

CHERECHEDZA:
Kana iyo programmable switch iri mu OFF chinzvimbo, simba rinogona kuramba rakabatidzwa nebhatani remagetsi. Kana iyo programmable switch ichibva yabatidzwa, meseji pfupi ichaonekwa paLCD.

Recorder Operating Mirayiridzo

• Isa bhatiri (ma)
• Isa microSDHC memori kadhi
• Batidza simba
• Fomati memori kadhi
• Batanidza maikorofoni woiisa panzvimbo ichashandiswa.
• Ita kuti mushandisi ataure kana kuimba pamwero mumwe chete uchashandiswa mukugadzira, uye gadzirisa kuwana kwekuisa kuitira kuti -20 LED inobwaira yakatsvuka pakakwirira.

Shandisa UP uye PASI museve mabhatani kugadzirisa kuwana kusvika iyo -20 LED ichibwaira yakatsvuka papamusoro pepamusoro.

• Dzvanya MENU/SEL, sarudza SDCard, uye Rekodha kubva kumenyu
• Kuti umise kurekodha, dzvanya MENU/SEL, sarudza SDCard, uye Mira; izwi rekuti SAVED rinobuda pascreen

CHERECHEDZA: Rekodha uye Mira Kurekodha zvakare inogona kuwanikwa nemakiyi mapfupi kubva kuhombe / imba skrini:

• Panguva imwe chete kudzvanya BACK bhatani + UP museve bhatani: Tanga kurekodha
• Panguva imwe chete kudzvanya BACK bhatani + PASI museve bhatani: Mira rekodhi

DBSM/DBSMD Mepu Mepu

• Kubva paHwindi Makuru, tinya MENU/SEL.
• Shandisa UP/DOWN arrow keys kusarudza chinhu.

Menu Screen Details

Top Menu
Kubva paDefault screen, kudzvanya MENU/SEL kuchawana iyo yepamusoro Menyu. Iyo Yepamusoro Menyu inobvumira mushandisi kuwana akasiyana-siyana mamenu ekudzora iyo unit.

Input Menyu
Kubva kuTopMenu, shandisa iyo uye mabhatani emiseve kuratidza INPUT uye tinya MENU/SEL.

Kugadzirisa Kupinza Kuwana
Iwo maviri bicolor Modulation LEDs pane control panel inopa inooneka chiratidzo cheiyo odhiyo siginecha nhanho ichipinda-ichifambisa. Iwo maLED anopenya angave matsvuku kana girinhi kuratidza modulation mazinga sezvakaratidzwa mune inotevera tafura.

CHERECHEDZA: Kuzara kwemodulation kunowanikwa pa0 dB apo iyo "-20" LED inotanga kutsvuka. Iyo limiter inogona kubata zvakachena kumusoro kusvika ku30 dB pamusoro peiyi poindi.

Zvakanakisa kuti uende kuburikidza neanotevera maitiro neinotapurirana mune yekumira modhi kuitira kuti pasave neaudio inopinda muodhiyo kana rekodhi panguva yekugadzirisa.

1. Iine mabhatiri matsva mune inotapurirana, simba iyo unit iri mumodhi yekumira (ona chikamu chapfuura Kubatidza Simba uye KUDZIMA).
2. Enda kuGain setup skrini.
3. Gadzirira kunobva chiratidzo. Isa maikorofoni nenzira yaichashandiswa mukushanda chaiko uye ita kuti mushandisi ataure kana kuimba zvine ruzha zvakanyanya zvichaitika panguva yekushandiswa, kana kuseta iyo yekubuda kwechiridzwa kana odhiyo mudziyo kusvika padanho repamusoro richashandiswa. .
4. Shandisa iyo uye mabhatani emuseve kuti agadzirise kuwana kusvika iyo -10 dB yapenya girini uye iyo -20 dB LED inotanga kupenya tsvuku panguva yekukwirira kwepamusoro muodhiyo.
5. Kana iyo yekuteerera yaiswa, chiratidzo chinogona kutumirwa kuburikidza neruzha sisitimu yeakazara nhanho kugadzirisa, yekutarisa marongero, nezvimwe.
6. Kana iyo odhiyo yekubuda level yeanogamuchira yakakwira zvakanyanya kana yakaderera, shandisa chete zvidzoreso pane anogamuchira kugadzirisa. Gara uchisiya iyo transmitter kuwana gadziriso yakaiswa zvinoenderana neiyi dzidziso, uye usachinje kuti ugadzirise odhiyo yekubuda nhanho yeanogamuchira.

Kusarudza iyo Yakaderera Frequency Roll-off
Zvinogoneka kuti iyo yakaderera-frequency roll-off point inogona kukanganisa kuisirwa kurongeka, saka zvakajairika tsika yakanaka kuita iyi gadziriso usati wagadzirisa kuwana kwekuisa. Nzvimbo iyo roll-off inoitika inogona kuiswa kune:

• LF 20 20 Hz
• LF 35 35 Hz
• LF 50 50 Hz
• LF 70 70 Hz
• LF 100 100 Hz
• LF 120 120 Hz
• LF 150 150 Hz

Iyo roll-off inowanzogadziriswa nenzeve uchitarisa odhiyo.

Kusarudza Audio polarity
Odhiyo polarity inogona kutenderedzwa kune transmitter kuitira kuti odhiyo isanganiswe nemamwe maikorofoni pasina kusefa muzinga. Iyo polarity inogona zvakare kudzoserwa kune inogamuchira zvinobuda.

Kusarudza LineIn/Instrument
Odhiyo yekupinza inogona kusarudzwa senge LineIn kana Instrument Level.

Xmit Menu
Shandisa iyo uye mabhatani emiseve kusarudza iyo Yekufambisa Menyu kubva kumusoro menyu.

Kusarudza Frequency
Iyo yekuseta skrini yekusarudzwa kwefrequency inopa nzira dzinoverengeka dzekutarisa ma frequency anowanikwa.

Kudzvanya MENU/SEL kuchachinja frequency minda. Iyo frequency yeMHz ichachinja mumatanho e1 MHz, iyo frequency yeKHz ichachinja mumatanho makumi maviri neshanu KHz.

Kuseta Transmitter Output Power
Simba rekubuda rinogona kuiswa ku:

• 10, 25 kana 50 mW, kana HDM (High Density Mode)

RF On?
RF transmission inogona kuvhurwa kana kuvharwa uchishandisa iyo uye mabhatani emiseve.

Compact Menu

Kusarudza iyo Compatibility Mode

• Shandisa iyo uye mabhatani emuseve kuti usarudze modhi yaunoda, wobva wadzvanya bhatani rekudzokera kaviri kuti udzokere kuMain Window.
• Compatibility modes ndeaya anotevera:
  DBSM/DBSMD:
  • Standard Mono Digital D2
  • High-Density Mode HDM

HDM Mode (High Density Transmission)
Iyi yakakosha yekufambisa modhi uye yakabatana yakaderera RF simba re2mW inobvumira mushandisi "kuisa" akawanda mayuniti munzvimbo diki diki yechiratidziro. Yakajairwa, ETSI-inoenderana neRF vatakuri vanotora ingangoita mazana maviri kHz yeyakagarwa bandwidth, nepo HDM inotora inenge hafu yeiyo, kana zana kHz, uye inobvumira kusimba kwakanyanya kwechiteshi.

SD Card Menyu
Iyo SD Kadhi Menyu inogona kuwanikwa kubva kuTopMenu. Iine akasiyana mabasa ekurekodha, file manejimendi, uye mazita.

Record
Kusarudza izvi kunotanga unit kurekodha. Kuti umise kurekodha, dzvanya MENU/SEL, sarudza SDCard, uye Mira; izwi rekuti SAVED rinobuda pascreen.

CHERECHEDZA:
Rekodha uye Mira Kurekodha zvakare inogona kuwanikwa nemakiyi mapfupi kubva kuhombe / imba skrini:

• Panguva imwe chete kudzvanya BACK bhatani + UP museve bhatani: Tanga kurekodha
• Panguva imwe chete kudzvanya BACK bhatani + PASI museve bhatani: Mira rekodhi

Files
Iyi skrini inoratidza zviripo files pane SD kadhi. Kusarudza a file icharatidza ruzivo nezve file.

Viewing Inotora
Shandisa UP uye PASI miseve kuchinja uye MENU/SEL kuti view inotora.

Kuridza zvakarekodhwa, bvisa memori kadhi uye kopira iyo files pakombiyuta ine vhidhiyo kana audio editing software yakaiswa.

Kuisa Scene uye Tora Nhamba
Shandisa UP uye PASI miseve kufambisira mberi Chiitiko uye Tora uye MENU/SEL kuchinjisa. Dzvanya bhatani rekuti BACK kuti udzokere kumenyu.

Format
Inogadzirisa iyo microSDHC memori kadhi.

YAMBIRO:
Iri basa rinodzima chero zvirimo pane microSDHC memori kadhi.

Recorded File Kutumidza mazita
Sarudza kudoma zvakarekodhwa files nenhamba yekutevedzana, nguva yewachi, kana chiitiko uye kutora.

SD Info
Ruzivo nezve microSDHC memori kadhi kusanganisira nzvimbo yasara pakadhi.

Load Group
Sarudza zita reboka re frequency pane SD kadhi kuti uise.

Sevha Boka
Sarudza zita reboka re frequency kuti uchengetedze pane SD kadhi.

TCode Menu

TC Jam (jam timecode)

• Kana TC Jam yasarudzwa, JAM ZVINO ichabwaira paLCD uye iyo unit yakagadzirira kuyananiswa neye timecode sosi. Batanidza timecode sosi uye sync ichaitika otomatiki. Kana sync yabudirira, meseji icharatidzwa kuratidza kushanda.
• The timecode defaults to 00:00:00 at power-up kana pasina nguva-code sosi inoshandiswa jam unit. Referensi yenguva inopindirwa muBWF metadata.

CHERECHEDZA:
Iyo timecode yekupinda yeDBSM iri mune 5-pini mic yekupinda. Kuti ushandise timecode, bvisa mic connector woitsiva ne timecode sync adapter cable. Isu tinokurudzira MCTCTA5BNC kana MCTCA5LEMO5 (ona Optional Accessories). Wiring inogadziriswa papeji 16.

Kuisa Frame Rate

Iyo furemu mwero inokanganisa kuiswa kwereferensi yenguva mu. BWF file metadata uye kuratidzwa kwetimecode. Izvi zvinotevera zvingasarudzwa zviripo:

• 30
• 23.976l
• 24
• 29.97
• 30DF
• 25
• 29.97DF

CHERECHEDZA:
Kunyange zvichikwanisika kushandura furemu chiyero, iyo inonyanya kushandiswa ichave yekutarisa furemu chiyero chakagamuchirwa panguva yazvino nguva yekodhi jam. Muzviitiko zvisingawanzoitiki, zvingave zvakakosha kushandura chiyero pano, asi ziva kuti matepi ekuteerera anogona kusamira zvakanaka nemazinga asina kuenderana.

Shandisa Clock
Iyo DBSM nguva wachi uye karenda (RTCC) haigone kuvimbwa nayo seyakarurama nguva kodhi sosi. Shandisa Clock inofanirwa kushandiswa chete kana pasina chikonzero chenguva yekubvumirana neyekunze timecode sosi.

IR&Kiyi Menyu

SendFreq
Dzvanya MENU/SEL kuwiriranisa Frequency kune imwe transmitter kana inogamuchira kuburikidza neIR port.

SendAll
Dzvanya MENU/SEL kuwiriranisa: Frequency, Transmitter Name, Talkback Inogoneswa, uye Inoenderana Modhi kune imwe transmitter kana inogamuchira kuburikidza neIR port.

CHERECHEDZA:
SendAll haitumire Encryption Key. Izvi zvinofanira kuitwa zvakasiyana.

GetFreq
Dzvanya MENU/SEL kuwiriranisa Frequency kune imwe transmitter kana inogamuchira kuburikidza neIR port.

GetAll
Dzvanya MENU/SEL kuwiriranisa: Frequency, Transmitter Name, Talkback Inogoneswa, uye Inoenderana Modhi kubva kune imwe transmitter kana inogamuchira kuburikidza neIR port.

KeyType
Iyo DBSM/DBSMD inogamuchira kiyi yekuvharidzira kuburikidza neIR port kubva kune kiyi-inogadzira inogamuchira. Tanga nekusarudza rudzi rwekiyi muunogamuchira uye kugadzira kiyi nyowani (rudzi rwekiyi yakanyorwa KEY POLICY muDSQD inogamuchira).

Seta inofananidzwa KEY TYPE muDBSM/DBSMD woendesa kiyi kubva kune inogamuchira (SYNC KEY) kuenda kuDBSM/DBSMD kuburikidza neIR ports. Meseji yekusimbisa icharatidza pane inogamuchira kana kutamisa kwabudirira. Iyo inofambiswa odhiyo inozovharwa uye inogona kuteererwa chete kana inogamuchira ine inoenderana encryption kiyi.

Iyo encryption system muLectrosonics Digital modes D2, DCHX, uye HDM inogona kugadzirwa nenzira ina dzakasiyana, yakatemwa neparameter inozivikanwa seKiyi Type. Idzo mhando ina dzakakosha dzinobva padzisina kuchengetedzeka zvishoma asi dzakanyanya nyore, kusvika kune dzakachengetedzeka zvakanyanya asi dzisiri nyore. Pazasi pane tsananguro dzeMarudzi mana Akakosha uye kuti anoshanda sei.

• Universal: Iyi ndiyo yakasarudzika kiyi mhando, iri nyore kushandisa, uye yakachengeteka zvishoma. Nepo encryption iri kuitwa nehunyanzvi uye scanner kana nyore demodulator yaisaburitsa chiratidzo chemukati, kutaurirana hakuna kuchengetedzeka. Izvi zvinodaro nekuti zvese zvigadzirwa zveLectrosonics zvinoshandisa iyo Universal kiyi mhando inoshandisa iyi imwechete "universal" encryption kiyi. Neiyi kiyi mhando yakasarudzwa, makiyi haafanire kugadzirwa kana kuchinjana, uye michina isina waya inogona kushandiswa pasina kutarisisa kune encryption chimiro.
• Yakagovaniswa: Iyi ndiyo iri nyore encryption modhi yekushandisa paunenge uchishandisa kiyi inogadzirwa. Iyi kiyi mhando inopa chengetedzo yakanakisa uye kuchinjika kukuru. Kana kiyi yagadzirwa, inogona kugovaniswa nhamba isina muganho yenguva nechero chinhu chinoenderana icho, ichowo, chinogona kugovera kiyi. Izvi zvinonyanya kubatsira kana akawanda anogashira angangoda kutora akasiyana transmitters.
• Standard: The Standard kiyi mhando inopa yakawedzera chengetedzo, pamutengo wekumwe kuoma. Makiyi akajairwa "chiitiko chinodzorwa", izvo zvinobvumira iyo Hardware kudzivirira kubva "kurwiswa kwakasiyana". A Standard kiyi inogona chete kutumirwa nemudziyo wakaigadzira, uye chete kusvika ku256 nguva. Kusiyana nemakiyi Akagoverwa, zvishandiso zvinogamuchira kiyi yeStan-dard hazvigone kuipfuudza.
• Volatile: Iyo Volatile kiyi mhando ndiyo yakachengeteka zvakanyanya, uye zvakare isingaite nyore kushandisa. Makiyi eVolatile anoita zvakafanana kune Standard kiyi, kunze kwekuti haana kumbochengetwa. Equipment inodzimwa uchishandisa Volatile kiyi inodzoka isina kiyi. Kana mudziyo wekugadzira kiyi ukasiiwa, kiyi inogona kugovaniswa zvakare nemayunitsi muhurongwa akarasa makiyi. Kana zvese zvishandiso zvashandisa yakapihwa Volatile kiyi yakadzimwa, kiyi iyoyo inoparadzwa. Izvi zvinogona kudiwa mune dzimwe nzvimbo dzakachengeteka zvakanyanya.

WipeKey
Ichi chinhu chemenu chinowanikwa chete kana Kiyi Type yakasetwa kune Standard, Shared, kana Volatile. Sarudza Hongu kupukuta kiyi iripo uye kugonesa DBSM/DBSMD kugamuchira kiyi nyowani.

Setup Menu

AutoOn
Dzvanya MENU/SEL kushandura kana kudzima iyo AutoOn ficha.

Remote
Dzvanya MENU/SEL kushandura kana kudzima Remote “dweedle tone”.

BattType
Dzvanya MENU/SEL kusarudza ingave yeAlkaline kana Lithium bat-tery. Lithium mabhatiri anokurudzirwa.

Clock
Dzvanya MENU/SEL kuseta wachi (nguva uye zuva).

Kukiya/Kuvhura Shanduko kune Zvirongwa
Shanduko kune zvigadziriso zvinogona kuvharwa muSimba Bhatani Menyu.

Kana shanduko dzakakiyiwa, akati wandei kudzora uye zviito zvinogona kushandiswa:

• Settings ichiri kugona kuvhurwa
• Mamenu achiri kugona kubhurwa
• Kana rakakiiwa, SIMBA RINOGONA KUDZIMWA CHETE nekubvisa mabhatiri.
• "Rima" rakakiiwa modhi inodzivirira kuratidzwa kuti kusauye kana mabhatani adzvanywa. Buda nekubata UP+DOWN kwemasekonzi matatu. Kusiyana neakajairwa Yakakiyiwa modhi, "Rima" rakakiiwa modhi hairambi kuburikidza nemagetsi kutenderera.

DispOff
Dzvanya MENU/SEL kushandura DisplayOff ficha pakati pe5 uye 30 masekonzi, kana kuimisa kuti igare iripo.

Akatungamirira Off
Kubva pane main menu skrini, kukurumidza kudzvanya kweUP museve bhatani unobatidza control panel maLED. Kurumidza kudzvanya bhatani re PASI museve unodzima. Mabhatani anozovharwa kana iyo AKADZIDZWA sarudzo yasarudzwa muPower Bhatani menyu.

Default
Dzvanya MENU/SEL kudzoreredza iyo Default (fekitari) marongero.

About
Dzvanya MENU/SEL kuratidza modhi, firmware version, software version, uye serial nhamba.

5-Pin Input Jack Wiring

• Lavalier maikorofoni uye adapta cabling inoshandiswa nedhijitari bodypack transmitters inofanirwa kunge iine shield waya yakabatana negoko remaikorofoni plug.
• Izvi zvinoderedza iyo RF simba rinovhenekerwa mukati meiyo maikorofoni tambo yekudzivirira waya kubva pakudzokera mutrans-mitter kuburikidza nekupinza odhiyo.
• Digital RF vatakuri vane zvese FM uye AM zvikamu uye yakakura kudzivirirwa maikorofoni inodiwa kukunda induced transmitter radio frequency interference. Iyo wiring diagraphs inosanganisirwa muchikamu chino inomiririra iyo yakakosha wiring inodiwa kune akajairika marudzi emakrofoni uye mamwe maodhiyo ekuisa. Mamwe maikorofoni angada mamwe majeeti kana kuti musiyano mudiki pamadhayagiramu anoratidzwa.
• Izvo hazvigoneke kuti ugare wakanyatso kuenderana nezve shanduko inoitwa nevamwe vagadziri kune yavo zvigadzirwa, nekudaro unogona kusangana nemakrofoni inosiyana nemirairo iyi. Kana izvi zvikaitika ndapota fonera yedu yemahara nhamba yakanyorwa pasi peSevhisi uye Gadzirisa mubhuku rino kana shanyira yedu websaiti pa: www.lectrosonics.com.

Audio yekupinda jack wiring:

• Pini 1
  Shield (pasi) yemakrofoni yakarerekera eelectret lavaliere. Shield (pasi) yemakrofoni ane simba uye mutsara-chikamu chekupinza.
• Pini 2
  Bias voltage sosi yezvakarerekera electret lavaliere maikorofoni asiri kushandisa servo bias circuitry uye voltage sosi ye4-volt servo bias wiring.
• Pini 3
  Maikorofoni nhanho yekupinza uye bias kupa.
• Pini 4
  • Bias voltage selector yePin 3.
  • Pini 3 voltage zvinoenderana nePin 4 yekubatanidza.
  • Pini 4 yakasungirirwa kuPin 1: 0 V
  • Pin 4 Vhura: 2 V
  • Pin 4 kusvika Pini 2: 4 V
• Pini 5
  Mutsetse nhanho yekupinda yematepi dhizaini, musanganiswa zvinobuda, zviridzwa zvemimhanzi, uye nguva kodhi jamming.

Cherechedza:
Kana iwe ukashandisa bhutsu yeguruva, bvisa iyo rubber strain relief yakasungirirwa kune TA5F cap, kana bhutsu haikwane pamusoro pegungano.

Kuisa Connector:

1. Kana zvichidikanwa, bvisa chekare chekubatanidza kubva kune maikorofoni tambo.
2. Svetedza bhutsu yeguruva pane maikorofoni tambo ine hombe yekupedzisira yakatarisana nechokubatanidza.
3. Kana zvichidikanwa, tsvedza iyo 1/8-inch dema shrink tubing pane maikorofoni tambo. Iyi tubing inodiwa kune mamwe madiki dhayamita tambo kuti ive nechokwadi chekuti pane snug fit muhuruva boot.
4. Svetedza iyo backshell pamusoro petambo sezvaratidzwa pamusoro. Svetedza insulator pamusoro petambo usati wasoneredza waya kumapini painoisa.
5. Solder waya uye resistors kune mapini pane inoiswa zvinoenderana nedhayagiramu inoratidzwa muWir-ing Hookups kune Different Source. Hurefu hwe .065 OD clear tubing inosanganisirwa kana iwe uchida kuisa insulate ma lead lead kana shield waya.
6. Kana zvichidikanwa, bvisa iyo rubber strain relief kubva kuTA5F backshell nekungoiburitsa kunze.
7. Gadzika insulator pane yekuisa. Svetera tambo clamp pamusoro uye ye insulator uye crimp sezvinoratidzwa papeji rinotevera.
8. Isa iyo yakaunganidzwa insert/insulator/clamp muchivharo chejira. Ita shuwa kuti iyo tebhu uye slot inomisikidza kuti ibvumire iyo yekuisa kuti igare zvizere mune yekukiya latch. Isa ganda rekumashure pane latchlock.

Maikorofoni Cable Kumiswa kweasiri-Lectrosonics Maikorofoni

TA5F Connector Assembly

Mic Cord Stripping Instruction

Crimping kune Shield uye Insulation
Bvisa uye uise tambo kuitira kuti clamp inogona kuvharirwa kubata zvese zviri zviviri mic tambo nhovo uye nekuisa. Iyo shield yekubata inoderedza ruzha nemamwe maikorofoni uye iyo insulation clamp kunowedzera ruggedness.

CHERECHEDZA:
Kumiswa uku kunoitirwa maUHF transmitters chete. VHF transmitters ine 5-pini jacks inoda kugumiswa kwakasiyana. Lectrosonics lavaliere maikorofoni anogumiswa kuti aenderane neVHF uye UHF transmitters. M152/7005P ine waya nenhovo kune yekubatanidza shell sezvakaratidzwa.

Input Jack Wiring kune Akasiyana Source

• Pamusoro peiyo maikorofoni uye mutsara-level wiring hook-ups inoratidzwa pazasi, Lectrosonics inogadzira akati wandei tambo uye adapta kune mamwe mamiriro akadai sekubatanidza zviridzwa zvemimhanzi (magitare, bass magitare, nezvimwewo) kune anotumira. Visit www.lectrosonics.com uye tinya pane Zvishandiso, kana kurodha iyo master catalog.
• Ruzivo rwakawanda nezve maikorofoni wiring inowanikwawo muFAQ chikamu che websaiti pa: http://www.lectrosonics.com/faqdb
• Tevedza mirairo yekutsvaga nemuenzaniso nhamba kana dzimwe sarudzo dzekutsvaga.

Inoenderana Wiring kune ese ari maviri Servo Bias Inputs uye Kare Transmitters:

Nyore Wiring - Inogona KUNGOshandiswa neServo Bias Inputs:
Servo Bias yakaunzwa muna 2005 uye ese matrans-mitters ane 5-pini yekupinda akavakwa nechinhu ichi kubvira 2007.

Maikorofoni RF Bypassing
Kana ichishandiswa pane isina waya inotapurirana, iyo maikorofoni chinhu chiri padyo neRF ichibva kune transmitter. Hunhu hwemakrofoni eelectret hunovaita kuti vanzwe kuRF, izvo zvinogona kukonzera matambudziko nemakrofoni/transmitter kuenderana. Kana maikorofoni ye electret isina kugadzirwa nemazvo kuti ishandiswe neasina waya, zvingave zvakafanira kuisa chip capacitor mu mic capsule kana chinongedzo kuvharira RF kuti isapinde mu electret capsule.

Mamwe maikorofoni anoda dziviriro yeRF kuchengetedza siginecha yeredhiyo kuti isakanganise capsule, kunyangwe iyo transmitter yekuisa wedunhu yatove RF yakapfuura. Kana iyo mic yakaitwa newaya sekurairwa, uye uri kunetseka nekuridza mhere, ruzha rwakanyanya, kana kutadza kupindura, RF ingangove iri honzeri.

Iyo yakanakisa RF dziviriro inoitwa nekuisa RF bypass capacitors pane mic capsule. Kana izvi zvisingagoneke, kana kana uchiri kunetseka, ma capacitor anogona kuiswa pama mic pini mukati meTA5F yekubatanidza imba. Tarisa kumufananidzo uri pasi apa kuti uwane nzvimbo yakarurama ye capacitors. Shandisa 330 pF capacitors. Macapacitors anowanikwa kubva kuLectrosonics. Ndapota tsanangura nhamba yechikamu chemaitiro ekutungamirira aunoda.

• Inotungamira capacitor: P/N 15117
• Leadless capacitors: P/N SCC330P

Yese Lectrosonics lavaliere mics yakatopfuura uye haidi mamwe macapacitor akaiswa kuti ashande zvakanaka.

Line Level Signals
Iyo wiring yemutsara level uye masaini ezviridzwa ndeiyi:

• Chiratidzo Chinopisa kupinza 5
• Signal Gnd kupinza 1
• Pin 4 yakasvetuka kusvika pini 1

Izvi zvinobvumira nhanho dzechiratidzo kusvika ku3V RMS kuti ishandiswe pasina kudzikisira.

CHERECHEDZA yezvinopinza mumutsara-pamwero chete (kwete chiridzwa): Kana imwe headroom ichidiwa, isa 20 k resistor munhevedzano nepini 5. Isa chinodzivirira ichi mukati meTA5F connector kuderedza kusimudza ruzha. Iyo resistor ichave nekushomeka kana kusave nemhedzisiro pachiratidzo kana iyo yekupinza yakasetwa kune chiridzwa.

Firmware Update

Firmware inogadziridza inogadzirwa uchishandisa microSDHC memori kadhi. Tarisa Revision nhoroondo pa websaiti kuti uone kuti ndeipi update yaunoda kuita.

CHERECHEDZA:
Ita shuwa kuti une mabhatiri matsva muyuniti yako usati watanga maitiro ekuvandudza. Kukundikana kwebhatiri kuchakanganisa uye pamwe kukanganisa iyo update file.

Dhawunirodha yakakodzera firmware version. Unzip uye tevedzera inotevera firmware update files kudhiraivha pakombuta yako:

• dbsm vX_xx.hex ndiyo firmware update file, apo "X_xx" iri nhamba yekudzokorora.
• dbsm_fpga_vX.mcs ndiyo inoperekedza board update file, apo "X" iri nhamba yekudzokorora.

Pakombiyuta:

1. Ita Quick Format yekadhi. PaWindows-based system, izvi zvinongogadzira kadhi kune iyo FAT32 fomati, inova iyo Windows standard. PaMac, unogona kupihwa akati wandei sarudzo. Kana iyo kadhi yakatofomatidzwa muWindows (FAT32) - ichaita greyed kunze - saka hapana chaunoda kuita. Kana kadhi iri mune imwe fomati, sarudza Windows (FAT32) wobva wadzvanya "Erase". Kana iyo yekukurumidza fomati pakombuta yapera, vhara iyo dialogue box uye vhura iyo file browser.
2. Kopa dbsm vX_xx.hex uye dbsm_fpga_ vX.mcs files kumemori kadhi, wobva waburitsa kadhi kubva pakombuta zvakachengeteka.

Mune DBSM:

1. Siya iyo DBSM yakadzimwa uye isa iyo microS-DHC memori kadhi mune slot.
2. Bata pasi ese UP uye PASI museve mabhatani pane rekodha uye wobatidza simba racho.
3. Iyo rekodha ichaita boot up mu firmware update mode neanotevera sarudzo paLCD:
   • Kwidziridzo - Inoratidza runyoro runofambiswa rwekuvandudza files pakadhi.
   • Power Off - Inobuda mugadziriso uye inodzima magetsi.
     CHERECHEDZA: Kana iyo unit skrini ichiratidza FORMAT CARD? dzima chikwata uye dzokorora danho 2. Wanga usiri kunyatsodzvanya UP, PASI, uye Simba panguva imwe chete.
4. Shandisa mabhatani emiseve kusarudza Update. Shandisa UP uye PASI museve mabhatani kusarudza zvaunoda file (vanoda kuvandudzwa mumwe nemumwe) uye tinya MENU/SEL kuti uise firmware. Iyo LCD icharatidza mamiriro mameseji apo firmware iri kuvandudzwa.
5. Kana iyo update yapera, LCD icharatidza iyi meseji: UPDATE SUCCESSFUL REMOVE CARD. Vhura gonhi rebhatiri, bvisa memori kadhi, wozoidzosera mukati uye wovhara musuwo.
6. Dzokorora matanho 1-5 kuti uvandudze imwe file.
7. Simba iyo unit idzoke. Simbisa kuti iyo firmware vhezheni yakagadziridzwa nekuvhura iyo Power Bhatani Menyu uye kuenda kune About chinhu. Ona peji 6.
8. Sezvo iwe uchiisa zvakare kadhi rakagadziridzwa uye wodzosera simba, iyo LCD inoratidza meseji inokukurudzira kuti ufomati kadhi:
   Format Card? (filendarasika)
   • Aihwa
   • Ehe

Iyo kadhi inomira kune iyo DATA fomati mushure mekugadzirisa. Kana uchida kurekodha odhiyo pakadhi, unofanira kuifomatidza zvakare. Sarudza Hongu uye dzvanya MENU/SEL kufometa kadhi. Kana maitirwo apera, LCD inodzokera kuMain Window uye yogadzirira kushanda zvakajairika. Kana ukasarudza kuchengeta kadhi sezvariri (DATA), unogona kubvisa kadhi panguva ino wovandudza imwe file kana zvichidiwa.

Bootloader Files:
Iyo firmware update process inotungamirirwa nebootload-er chirongwa - pane zvisingawanzo kuitika, ungangoda kugadzirisa bootloader.

YAMBIRO:
Kugadziridza iyo bootloader inogona kukanganisa unit yako kana ikakanganiswa. Usagadzirise bootloader kunze kwekunge warairwa kuti uite kudaro nefekitari.

• dbsm_boot vX_xx.hex ndiyo bootloader file

Tevedza maitiro akafanana neiyo firmware update uye sarudza iyo dbsm_boot file.

Recovery Process

Muchiitiko chekukundikana kwebheteri, apo chikwata chiri kurekodha, nzira yekudzorera inowanikwa kuti idzorere kurekodha mumhando yakakodzera. Kana bhatiri idzva raiswa uye unit ikadzoserwa zvakare, rekodha inoona iyo yakarasika data uye inokukurudzira kuti umhanye maitiro ekudzoreredza. The file inofanira kudzoserwa kana kadhi harizoshandiswi muDBSM/DBSMD.

Kutanga, ichaverenga:
Yakakanganiswa Kurekodha Yawanikwa

Iyo LCD meseji inobvunza:

Kupora?
kuti ushandise zvakachengeteka ona bhuku rekushandisa

Iwe uchave nesarudzo yeKwete kana Hongu (Kwete inosarudzwa seyekutanga). Kana iwe uchida kupora iyo file, shandisa bhatani re PASI museve kusarudza Hongu, wobva wadzvanya MENU/SEL. Iwindo rinotevera richakupa sarudzo yekudzoreredza zvese kana chikamu che file. Idzo nguva dzakasarudzika dzakaratidzwa ndiyo yakanyanya kufungidzira ne processor uko iyo file akamira kurekodha. Maawa acharatidzwa uye unogona kugamuchira kukosha kwakaratidzwa kana kusarudza nguva yakareba kana ipfupi. Kana usina chokwadi, ingogamuchira kukosha kwakaratidzwa sekusagadzikana.

Dzvanya MENU/SEL uye maminetsi anobva aratidzwa. Iwe unogona kuwedzera kana kuderedza nguva yekudzorerwa. Muzviitiko zvakawanda iwe unogona kungogamuchira kukosha kwakaratidzwa uye file achapora. Mushure mekuita sarudzo dzenguva yako, tinya MENU/SEL zvakare. A diki GO! sym-bol ichaonekwa padivi peiyo DOWN museve bhatani. Kudzvanya bhatani kunotanga file kupora. Kupora kuchaitika nekukurumidza uye iwe uchaona:

Kupora Kunobudirira

Special Note:
Files pasi pemaminetsi e4 kureba inogona kupora neimwe data "yakaiswa pa" kusvika kumagumo e file (kubva pane zvakarekodhwa kana data kana kadhi rakamboshandiswa kare). Izvi zvinogona kubviswa zvinobudirira mupositi nekudzima kuri nyore kweisingadiwe yakawedzera "ruzha" pakupera kweklipu. Hurefu hwakadzoserwa hudiki huchava miniti imwe. For exampuye, kana kurekodha kwakareba masekonzi makumi maviri chete, uye ukasarudza miniti imwe chete pachave neinodiwa 20 masekonzi akarekodhwa nemamwe masekonzi makumi mana eimwe data uye kana zvigadzirwa mu file. Kana usina chokwadi nezvehurefu hwekurekodha unogona kuchengetedza nguva yakareba file - panozongove neakawanda "junk" pakupera kweclip. Iyi "junk" inogona kusanganisira dhata rekuteerera rakarekodhwa muzvikamu zvekutanga zvakaraswa. Iyi "yakawedzerwa" ruzivo-runogona kubviswa nyore nyore mumashure ekugadzira editing software pane imwe nguva inotevera.

Silver Namira paTransmitter Thumbscrews

Silver paste inoiswa kune thumbscrew threads pamayuniti matsva pafekitori kuvandudza kubatana kwemagetsi kubva mukamuri yebhatiri kuburikidza neimba pane chero DBSM/DBSMD transmitter. Izvi zvinoshanda kune stand-dard bhatiri gonhi uye yekubvisa bhatiri.

Iro bhodhoro diki rakavharirwa rine hushoma (25 mg) hwesirivheri conductive paste. Chidimbu chidiki cheiyi paste chinovandudza conductivity pakati pebhatiri yekuvhara plate thumbscrew uye kesi yeDBSM/DBSMD.

• Iine yakagadziridzwa conductivity (yakaderera kuramba) yakawanda yebhatiri voltage inogona kusvika kune emukati magetsi ekushandisa zvichikonzera kuderedzwa ikozvino kudonha uye hupenyu hurefu hwebhatiri. Kunyangwe mari yacho ichiita sediki, inokwana makore ekushandiswa.
• Kutaura zvazviri, inopeta 25 uwandu hwatinoshandisa pazvigumwe pafekitari.
• Kuti uise sirivheri paste, kutanga, bvisa zvachose chivharo chevhavha kubva mudzimba nekutsigira thumbscrew zvachose kunze kwekesi. Shandisa jira rakachena, rakapfava kuchenesa shinda dzepagumwe.
• CHERECHEDZA: USASHANDISA doro kana mvura yekuchenesa.
• Ingo bata jira uchitenderedza shinda uye shandura chikona chechigunwe. Enda kunzvimbo itsva pamucheka uye uite zvakare. Ita izvi kusvikira jira raramba rakachena. Iye zvino, chenesa tambo mune iyo kesi uchishandisa yakaoma donje swab (Q-tip) kana yakaenzana. Zvekare, chenesa tambo dzekesi kusvika donje nyowani rabuda rakachena.
• Vhura bhodhoro, uye woendesa pinhead kapini kesirivheri paste kune yechipiri shinda kubva kumucheto kwegumwe-screw. Nzira iri nyore yekutora chidimbu chepaste ndeyekupetunura chikamu chebepa uye kushandisa kumagumo kwewaya kuwana diki diki repaste. A toothpick inoshandawo. Mari inovhara kupera kwewaya inokwana.
• Hazvina kudikanwa kuparadzira paste kupfuura zvishoma pane shinda sezvo paste ichazviparadzira yega nguva iyo thumbscrew inopindirwa mukati uye kunze kwekesi panguva yekuchinja kwebhatiri.
• Usaise paste kune chero imwe nzvimbo. Iyo inovhara ndiro pachayo inogona kucheneswa nejira rakachena nekukwesha zvindori zvakasimudzwa zvishoma pandiro painobata bhatiri terminal. Zvese zvaunoda kuita kubvisa chero mafuta kana tsvina pazvindori. Usabvise nzvimbo idzi nechinhu chakakasharara senge penzura eraser, emery bepa, zvichingodaro, sezvo izvi zvichibvisa conductive nickel plating uye kufumura iyo iri pasi pealuminium, inova isina kunaka yekubata conductor.

Yakarurama Whip Antennas

Antennas anopihwa nefekitori zvinoenderana netafura inotevera:

BAND	MABHUKU AKAFUKIWA	AKAPIWA ANTENNA
A1	470, 19, 20	AMM19
B1	21, 22, 23	AMM22
C1	24, 25, 26	AMM25

Iyo caps inopihwa inogona kushandiswa nenzira dzakasiyana siyana:

1. Chivharo chemavara pamagumo eshamhu
2. Sleeve yeruvara padivi pechibatanidza chine chivharo nhema pamucheto wetyava (cheka magumo akavharika evhavha yemavara nechigero kugadzira sleeve).
3. Sleeve yemuvara uye chivharo chemavara (cheka chivharo muhafu nechigero).

Iyi izere-saizi yekucheka template inoshandiswa kucheka kureba kweshamhu kune imwe frequency. Isa iyo antenna isina kuchekwa pamusoro peiyi dhizaini uye cheka kureba kwetyava kune yaunoda frequency. Mushure mekucheka antenna kusvika paurefu hwaunoda, maka antenna nekuisa kavha yeruvara kana sleeve kuratidza frequency. Kuisa mazita efekitari nekumaka zvakanyorwa patafura iri pazasi.

Cherechedza: Tarisa ukuru hwechinyorwa chako. Mutsetse uyu unofanira kureba 6.00 inches (152.4 mm).

Kumaka kuFactory uye Kuisa Mazita

BLOCK	FREQUENCY RANGE	CAP/SLEEVE COLOR	ANTENNA UREFU
470	470.100-495.600	Dema w/ Label	5.67 mukati./144.00 mm.
19	486.400-511.900	Dema w/ Label	5.23 mukati./132.80 mm.
20	512.000-537.575	Dema w/ Label	4.98 mukati./126.50 mm.
21	537.600-563.100	Brown w/ Label	4.74 mukati./120.40 mm.
22	563.200-588.700	Tsvuku w/ Label	4.48 mukati./113.80 mm.
23	588.800-607.950	Orange w/ Label	4.24 mukati./107.70 mm.
24	614.400-639.900	Yero w/ Label	4.01 mukati./101.85 mm.
25	640.000-665.500	Green w/ Label	3.81 mukati./96.77 mm.
26	665.600-691.100	Bhuruu w/ Label	3.62 mukati./91.94 mm.

Masero ane shaded ndiwo antenna anopihwa fekitori

CHERECHEDZA:
Hazvisi zvese zvigadzirwa zveLectrosonics zvakavakwa pane ese mabhururu akafukidzwa patafura iyi. Fekitari-inopihwa antenna precut kusvika kureba inosanganisira label ine frequency renji.

Belt Clips uye Pouches

Supplied Accessories

Optional Accessories

CHERECHEDZA:
Kunyangwe zvihomwe zvematehwe nemabhande ebhandi ewaya zvakasanganisirwa nehodha yako yekutanga, mahomwe ekuwedzera kana zvimedu zvinogona kuhodha uchishandisa nhamba yechikamu chimwechete chinoratidzwa papeji yakatarisana.

LectroRM

By New Endian LLC

• LectroRM inharembozha yeIOS uye Android smartphone inoshanda masisitimu. Chinangwa chayo ndechekuita shanduko kune zvigadziriso pane yakasarudzwa Lectrosonics transmitters nekuendesa encoded odhiyo toni kumakrofoni yakasungirirwa kune transmitter. Kana toni yapinda mutransmitter, inotemwa kuti iite shanduko kune akasiyana siyana marongero akadai sekuwana yekupinda, frequency, uye akati wandei evamwe.
• Iyo app yakabudiswa neNew Endian, LLC munaGunyana 2011. Inowanikwa pakudhawunirodha (yakabatanidzwa nePDR Remote) uye inotengesa nemadhora makumi maviri nemashanu paApple App Store neGoogle Play Store.
• Izvo zvigadziriso uye kukosha zvinogona kushandurwa zvinosiyana kubva kune imwe transmitter modhi kuenda kune imwe. Rondedzero yakazara yematoni anowanikwa muapp ndeaya:
  • Input gain
  • Frequency
  • Sleep Mode
  • Panel KUkiya/Vhura
  • RF kubuda simba
  • Low-frequency audio roll-off
  • LEDs ON/OFF

Iyo mushandisi interface inosanganisira kusarudza kutevedzana kwekuteerera kune hukama neshanduko yaunoda. Imwe neimwe vhezheni ine interface yekusarudza yaunoda kuseta uye inodiwa sarudzo yekuseta ikoko. Imwe neimwe vhezheni ine zvakare nzira yekudzivirira netsaona activation yetini.

iOS

Iyo iPhone vhezheni inochengeta yega yega inowanikwa pane imwe peji ine rondedzero yesarudzo dzeiyo kuseta. PaIOS, iyo "Activate" yekushandura switch inofanirwa kuve yakagoneswa kuratidza bhatani rinozovhura toni. Iyo iOS vhezheni's default orientation iri kumusoro-pasi asi inogona kugadzirwa kuti ienderere kumusoro-kurudyi kumusoro. Chinangwa cheizvi ndechekutungamira mutauri wefoni, iyo iri pazasi pechishandiso, padhuze neiyo maikorofoni yekutumira.

Android

Iyo Android vhezheni inochengeta ese marongero ari papeji imwe chete uye inobvumira mushandisi kuchinja pakati pemabhatani ekugadzirisa ega ega. Bhatani rekuita rinofanirwa kudzvanywa uye kubatwa kuti riite toni. Iyo Android ver-sion inobvumirawo vashandisi kuchengetedza rondedzero inogadziriswa yemaseti akazara ezvirongwa.

Activation
Kuti transmitter ipindure kune kure kure kudzora odhiyo toni, iyo inofambisa inofanirwa kuzadzisa zvimwe zvinodiwa:

• Iyo transmitter inofanirwa kubatidzwa.
• Iyo inotumira inofanirwa kunge iine firmware vhezheni 1.5 kana gare gare yeAudio, Frequency, Kurara, uye Kiya shanduko.
• Iyo maikorofoni yekutapurirana inofanirwa kunge iri mukati mechikamu.
• Iyo remote control function inofanirwa kugoneswa pane transmitter.

PDRRemote
Yakanakira kure kure kurekodha basa reDBSM rinopihwa nefoni app (yakaunganidzwa neLectroRM) inowanikwa paAppStore neGoogle Play. Iyo app inoshandisa maodhiyo toni ("tweedle tones") inoridzwa kuburikidza nefoni mutauri inodudzirwa nerekodha kuita shanduko kumasetin'arekodha:

• Rekodha Kutanga / Mira
• Mic Gain Level
• Kiya/kiinura

Matoni eMTCR akasarudzika kune MTCR uye haaite kune "tweedle toni" inoitirwa Lectrosonics transmitters. Masikirini anotaridzika zvakasiyana kune iOS uye Android mafoni asi anoita mabasa mamwe chete.

For Best Results
Mamiriro anotevera anodiwa:

• Maikorofoni inofanira kuva pakati penzvimbo.
• Iyo rekodha inofanirwa kugadzirwa kuti igone kugonesa remote control activation. Ona Remote pane menyu.

iOS Version

Android Version

• Ndokumbira uzive kuti maapplication aya haasi eLectrosonics zvigadzirwa.
• LectroRM uye PDRRemote ndeyavo uye inoshandiswa neNew Endian LLC, www.newendian.com.
• Tarisa kwavari websaiti yekuwedzera tekinoroji uye zviwanikwa zvekutsigira.

Zvinotsanangurwa

Operating frequency:

• DBSM(D)-A1B1: Bhendi A1-B1: 470.100 – 607.950
• DBSM(D)/E01-A1B1: Bhendi A1-B1: 470.100 – 614.375
• DBSM(D)/E01-B1C1: Bhendi B1-C1: 537.600 – 691.175
• DBSM (D)/E09-A1B1 Bhendi A1-B1: 470.100 – 614-375
• DBSMD (D)/E09-A1B1 Bhendi A1-B1: 470.100 – 614-375

CHERECHEDZA:
Ibasa remushandisi kusarudza ma frequency akatenderwa edunhu riri kushanda netransmitter

• Channel Spacing: 25 kHz
• RF Simba kuburitsa:
  • DBSM: 2 (HDM chete), 10, 25 kana 50 mW
  • DBSMD: 2 (HDM chete), 10, 25 kana 50 mW
  • DBSM(D)/E01-A1B1: 2 (HDM chete), 10, 25 kana 50 mW
  • DBSMD(D)/E01-B1C1: 2 (HDM chete), 10, 25 kana 50mW
  • DBSM/E09-A1B1: 2 (HDM chete), 10, 25 mW
  • DBSMD/E09-A1B1: 2 (HDM chete), 10, 25 mW
• Kuenderana Modes: DBSM/DBSMD: D2 dhijitari ine encryption, uye HDM yakakwirira-density dhijitari ine encryption.
• Modulation Type: 8 PSK
• Encryption Type: AES-256 muCTR modhi
• Frequency kugadzikana: ± 0.002%
• Spurious radiation: Inoenderana neETSI EN 300 422-1
• Ruzha rwakaenzana rwekuisa: -125 dBV, A-yakayerwa
• Chiyero chekupinza:
  • Kana yakagadzirirwa dynamic mic: 0.5 mV kusvika 50 mV isati yamisa Yakakura kupfuura 1 V nekumisa
  • Kana yakagadzirirwa electret lavaliere mic: 1.7A kusvika 170 uA isati yamisa Hukuru pane 5000 uA (5 mA) nekumisa
  • Mutsara nhanho yekupinda: 17 mV kusvika 1.7 V usati wamisa Kukura kupfuura 50 V nekudzikamisa
• Input impedance:
  • Dynamic maikorofoni: 300 Ohms
  • Electret lavaliere: Input ivhu rechokwadi rine servo yakagadziridzwa inogara yakarerekera iripo
  • Line level: 2.7 k ohms
• Input limiter: Soft limiter, 30 dB renji
• Bias voltages: Yakagadziriswa 5 V kusvika ku5 mA
  Inosarudzwa 2 V kana 4 V servo bias kune chero electret lavaliere
• Gain control range: -7 kusvika 44 dB; panel-yakaiswa membrane switch
• Modulation zviratidzo: Dual bicolor LEDs dzinoratidza modulation -20, -10, 0, +10 dB inonongedzwa kuzere modulation.
• Kudzora: Control panel w/ LCD uye 4 membrane switch
• Low-frequency roll-off: Inogadziriswa kubva pa20 kusvika ku150 Hz
• Input Type: Analog mic/line level inoenderana; servo bias preamp ye2V uye 4V Lavaliere maikorofoni
• Chiyero chekupinza:
  • Dynamic mic: 0.5 mV kusvika 50 mV
  • Electret mic: Nominal 2 mV kusvika 300 mV
  • Line level: 17 mV kusvika 1.7 V
• Input connector: TA5M 5-pini murume
• Audio Performance
  • Frequency mhinduro: 20Hz kusvika 20kHz, +/- 1dB: D2 Modhi 20Hz kusvika 16KHz, +/- 3dB: High Density (HDM) Mode
  • Dynamic range: 112 dB (A)
  • Kukanganisa: <0.035%
• Antenna: Flexible, isingaputsike simbi tambo.
• Bhatiri: AA (+1.5 VDC), inoraswa, Lithium inokurudzirwa

	Lithium	Alkaline	NiMH
DBSM-A1B1 (1 AA):	2 mw – 8:55 10 mw – 7:25 25 mw – 6:35 50 mw – 4:45	2 mw – 2:15 10 mw – 2:00 25 mw – 1:25 50 mw – 1:10	2 mw – 5:25 10 mw – 4:55 25 mw – 4:25 50 mw – 4:20
DBSMD-A1B1 (2 AA):	2 mw – 18:20 10 mw – 16:35 25 mw – 15:10 50 mw – 12:10	2 mw – 7:45 10 mw – 7:10 25 mw – 6:20 50 mw – 4:30	2 mw – 10:55 10 mw – 10:30 25 mw – 9:20 50 mw – 7:25

• Huremu nebhatiri(s):
  • DBSM-A1B1: 3.2 oz. (90.719 gramu)
  • DBSMD-A1B1: 4.8 oz. (136.078 gramu)
• Zvose Zviyero:
  • DBSM-A1B1: 2.366 x 1.954 x 0.642 inches; (isina maikorofoni) 60.096 x 49.632 x 16.307 mm
  • DBSMD-A1B1: 2.366 x 2.475 x 0.642 inches; 60.096 x 62.865 x 16.307 mm
• Emission Designator:
  • DBSM-A1B1/DBSMD-A1B1: 170KG1E (D2 mode)
  • DBSM-A1B1/DBSMD-A1B1: 110KG1E (HD mode)

Recorder

• Kuchengetedza midhiya: microSDHC memori kadhi
• File fomati: .wav files (BWF)
• A/D converter: 24-bit
• Sampchiyero chenguva: 48 kHz
• Kurekodha modes/Bit rate:
  • HD mono mode: 24 bit - 144 kbytes/s

Input

• Rudzi: Analog mic/line level inoenderana; servo bias preamp ye2V uye 4V Lavaliere maikorofoni
• Chiyero chekupinza:
  • Dynamic mic: 0.5 mV kusvika 50 mV
  • Electret mic: Nominal 2 mV kusvika 300 mV
  • Line level: 17 mV kusvika 1.7 V
• Input connector: TA5M 5-pini murume
• Audio Performance
  • Frequency mhinduro: 20Hz kusvika 20kHz, +/- 1dB:
  • Dynamic range: 112 dB (A)
  • Kukanganisa: <0.035%
• Kushanda tembiricha range
  • Celsius: -20 kusvika 50
  • Fahrenheit: -5 kusvika 122

Zvinyorwa zvinogona kuchinja pasina chiziviso.

Inowanika Kurekodha Nguva
Uchishandisa microSDHC* memori kadhi, nguva dzekurekodha dzakaita seinotevera. Nguva chaiyo inogona kusiyanisa zvishoma kubva kune zvakakosha zvakanyorwa mumatafura.

(HD mono mode)

Size	Hrs:Min
8GB	11:10
16GB	23:00
32GB	46:10

Kugadzirisa matambudziko

Slow Card Yambiro Paunenge uchirekodha 

1. Chikanganiso ichi chinozivisa mushandisi kuti kadhi harigone kuenderana nekumhanya uko DBSM iri kurekodha data.
2. Izvi zvinogadzira mikaha midiki mukurekodha.
3. Izvi zvinogona kupa dambudziko kana kurekodha kuchizo wiriraniswa nemamwe maodhiyo kana vhidhiyo.

Basa uye Kugadzirisa

Kana system yako ikasashanda, iwe unofanirwa kuyedza kugadzirisa kana kupatsanura dambudziko usati wafunga kuti mudziyo unoda kugadziriswa. Ita shuwa kuti watevera nzira yekuseta uye mirairo yekushandisa. Tarisa tambo dzekubatanidza uye wobva waenda kuburikidza neChikamu cheMatambudziko mubhuku rino.

Isu tinokurudzira zvakasimba kuti usaedze kugadzirisa midziyo iwe pachako uye usave nechitoro cheko chekugadzirisa chero chimwe chinhu kunze kwekugadzirisa kuri nyore. Kana kugadzirisa kunonyanya kuoma kupfuura tambo yakaputsika kana kusununguka kushamwaridzana, tumira chikwata kufekitari kuti chigadziriswe uye basa. Usaedze kugadzirisa chero zvinodzora mukati memayuniti. Kana yangoiswa pafekitari, zvidzoreso zvakasiyana uye zvigadziriso hazvifambi nezera kana kudedera uye hazvidi kugadziridzwa. Iko hakuna kugadziriswa mukati kuchaita kuti chikwata chisingaiti chitange kushanda.

LECTROSONICS' Dhipatimendi Rebasa rakashongedzerwa uye rine vashandi kuti vakurumidze kugadzirisa midziyo yako. Mune waranti, kugadzirisa kunoitwa pasina muripo nemitemo yewaranti. Kugadziriswa kwekunze-kwe-waranti kunobhadhariswa pamutengo wakadzikama pamwe nezvikamu uye kutumira. Sezvo zvichitora inenge nguva yakawanda uye simba kuti uone kuti chii chakaipa sezvazvinoita kugadzirisa, pane mari yekotesheni chaiyo. Isu tichafara kutora fungidziro yekuchaja nefoni yekunze-kwe-waranti yekugadzirisa.

Kudzorera Zvikwata zveKugadzirisa
Kuti uite sevhisi yenguva, ndapota tevera matanho ari pasi apa:

• USAZOdzosera zvishandiso kufekitori kuti zvigadziriswe usati watanga kutibata neemail kana nerunhare. Isu tinofanirwa kuziva mamiriro edambudziko, nhamba yemuenzaniso, uye serial nhamba yemidziyo. Isu tinodawo nhamba yefoni kwaunogona kusvika 8 AM kusvika 4 PM (US Mountain Standard Time).
• Mushure mekugamuchira chikumbiro chako, tinokupa iwe nhamba yemvumo yekudzosera (RA). Iyi nhamba ichabatsira kukurumidza kugadzirisa kwako kuburikidza nemadhipatimendi edu ekugamuchira nekugadzirisa. Nhamba yemvumo yekudzoka inofanira kuratidzwa zvakajeka kunze kwebhokisi rekutumira.
• Rongedza midziyo nekungwarira uye utumire kwatiri, mari yekutumira inobhadharwa kare. Kana zvichidikanwa, tinogona kukupa zvinhu zvakakodzera zvekurongedza. UPS kazhinji ndiyo nzira yakanakisa yekutumira mayunitsi. Heavy units inofanira kunge iri "double-boxed" kuitira kutakura zvakachengeteka.
• Isu tinokurudzirawo zvakasimba kuti iwe uise inishuwarenzi yemidziyo, sezvo isu hatigone kuve nemhosva yekurasikirwa kana kukuvadzwa kwemidziyo yaunotumira. Ehe, isu tinochengetedza midziyo kana isu tichitumira iyo kudzokera kwauri.

Lectrosonics USA:

• Kero yetsamba: Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA
• Web: www.lectrosonics.com

Lectrosonics Canada:

• Kero Yetsamba:
  720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9
• Kero yekutumira
  Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA
• E-mail:
  sales@lectrosonics.com
• Runhare:
  • 416-596-2202
  • 877-753-2876 Yemahara
  • (877-7LECTRO)
  • 416-596-6648 Fax
• Runhare:
  • 505-892-4501
  • 800-821-1121 Yemahara
  • 505-892-6243 Fax
• E-mail:
  • Sales: colinb@lectrosonics.com
  • Sevhisi: joeb@lectrosonics.com.

Kuzvibatsira Sarudzo dzeZvinetso Zvisiri Zvekukurumidza
Mapoka edu eFacebook uye web rondedzero hupfumi hweruzivo rwemushandisi mibvunzo uye ruzivo. Tarisa kune:

• Lectrosonics General Facebook Group: https://www.facebook.com/groups/69511015699
• D Squared, Nzvimbo 2 uye Wireless Designer Group: https://www.facebook.com/groups/104052953321109
• The Wire Lists: https://lectrosonics.com/the-wire-lists.html.

Zvekupfekwa nemuviri, iyi modhi yetransmitter yakaedzwa uye inosangana neFCC RF exposure nhungamiro kana yakashandiswa neLectrosonics accessories inopihwa kana kusarudzirwa chigadzirwa ichi. Kushandiswa kwezvimwe zvinhu zvinogona kusave nechokwadi chekutevedzwa neFCC RF ratidziro nhungamiro. Bata Lectrosonics kana uine chero mibvunzo kana uchida rumwe ruzivo nezve RF kuratidzwa uchishandisa chigadzirwa ichi. Mudziyo uyu unoenderana neFCC radiation exposure limits sekutemerwa nharaunda isingadzoreki. Chishandiso ichi chinofanirwa kuiswa uye kushandiswa kuitira kuti antenna (ma) ayo asave pamwe chete kana kushanda akabatana nechero imwe antenna kana transmitter.

ISEDC Zviziviso:

Per RSS-210
Ichi chishandiso chinoshanda pane-isina-kudzivirira hapana-kupindira. Kana mushandisi achida kuwana dziviriro kubva kune mamwe masevhisi eredhiyo anoshanda mumabhendi mamwe chete eTV, rezinesi reredhiyo rinodiwa. Ndokumbira utarise gwaro reIndasitiri Canada CPC-2-1-28, Optional Licensing yeLow-Power Radio Apparatus muTV Band, kuti uwane ruzivo.

Per RSS-Gen
Mudziyo uyu unoenderana neIndustry Canada's rezinesi-exempt RSSs. Kushanda kunoenderana nemamiriro maviri anotevera:

1. Mudziyo uyu unogona kusakonzera kukanganisa
2. Muchina uyu unofanirwa kugamuchira chero kukanganisa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingade kwemudziyo.

LIMITED RIMWE-GORE WARRANTY

Midziyo iyi inobvumidzwa kwegore rimwe kubva pazuva rayakatengwa kune chakaremara mumidziyo kana magadzirirwo kunze kwekunge yakatengwa kumutengesi ane mvumo. Iyi waranti haivharidzi midziyo yakashungurudzwa kana kukuvadzwa nekubata zvisina hanya kana kutumira. Iyi waranti haishande kune yakashandiswa kana dhizaini michina.

Kana chero chakakanganisika chikakura, Lectrosonics, Inc., pakusarudza kwedu, ichagadzirisa kana kutsiva chero nhengo dzakaremara pasina muripo wezvikamu kana basa. Kana Lectrosonics, Inc. isingakwanise kugadzirisa kukanganisa mumidziyo yako, inotsiviwa pasina muripo nechinhu chitsva chakafanana. Lectrosonics, Inc. ichabhadhara mutengo wekudzosera mudziyo wako kwauri. Waranti iyi inongoshanda kuzvinhu zvakadzorerwa kuLectrosonics, Inc.

Iyi Yakaganhurirwa Warranty inotongwa nemitemo yeNyika yeNew Mexico. Inotaura mutoro wose weLectrosonics Inc. uye mushonga wose wemutengi kune chero kukanganisa kwewaranti sezvakatsanangurwa pamusoro. Kwete lleponsonics, inc. WAKAPIRWA ZVINOGONA KUNYANYA CHEKUKATADZWA KWAKADA. HAPANA CHIITIKO CHINOGONA KUBVA CHELECTROSONICS, INC. ZVINOPIRIRA MUTENGO WEKUTENGWA WECHINHU CHECHINHU CHISINA ZVINHU.

Warrandi iyi inokupa kodzero dzemutemo. Unogona kunge uine dzimwe kodzero dzemutemo dzinosiyana kubva kune imwe nyika nenyika.

• 581 Laser Road NE • Rio Rancho, NM 87124 USA
• www.lectrosonics.com
• 505-892-4501
• 800-821-1121
• fax 505-892-6243
• sales@lectrosonics.com.

Zvinyorwa / Zvishandiso

LECTROSONICS DBSM-A1B1 Digital Transcorder [pdf] Bhuku reMirayiridzo DBSM-A1B1, DBSM-E01-A1B1, DBSM-E01-B1C1, DBSMD-A1B1, DBSMD-E01-A1B1, DBSMD-E01-B1C1, DBSM-E09-A1B1, DBSMD-E09-DSM-B1B1B1, DBSMD-E1-A1B1BXNUMXBXNUMXBXNUMX, DBSM-AXNUMXBXNUMX, Digital Transcorde, Transcorder

References

• User Manual