Danfoss Gasi Detection Controller Unit uye Kuwedzera Module Mushandisi Wekushandisa

ENGINEERING MANGWANA
User Guide
Danfoss Gasi Kuonekwa
Controller chikwata uye
Module yekuwedzera

Zviri mukati hide

1 Chinangwa chekushandisa

6 Zvinyorwa / Zvishandiso

6.1 References

Chinangwa chekushandisa

Danfoss gasi kuona gasi controller unit iri kudzora imwe kana akawanda gasi detector, yekutarisa, kuona uye yambiro yehupfu uye inopfuta magasi uye mhute mumhepo yakadzika. Iyo controller unit inosangana nezvinodiwa zvinoenderana neEN 378 uye nhungamiro "Kuchengetedza zvinodiwa zveammonia (NH3) mafiriji masisitimu".
Nzvimbo dzakatarisirwa inzvimbo dzese dziri kubatana zvakananga kune yeruzhinji low voltage kupa, semuenzaniso nzvimbo dzekugara, dzekutengesa uye dzemaindasitiri pamwe nemabhizinesi madiki (maererano neEN 5502).
Iyo controller unit inogona kungoshandiswa mune ambient mamiriro sekutsanangurwa kwehunyanzvi data.
Iyo controller unit haifanirwe kushandiswa munzvimbo dzinogona kuputika.

Tsanangudzo

Iyo controller unit yambiro uye yekudzora unit yekuenderera mberi kwekutarisa kweakasiyana ane muchetura kana anopfuta magasi nemhute pamwe neHFC neHFO mafiriji. Iyo controller unit inokodzera kubatana kweanosvika makumi mapfumbamwe nematanhatu edhijitari sensors kuburikidza ne96-waya bhazi. Kusvikira ku 2 analog inputs yekubatana kwema sensors ane 32 kusvika 4 mA signal interface inowanikwa mukuwedzera.
Iyo controller unit inogona kushandiswa seyakachena analog controller, seanalog/digital kana sedhijitari controller. Huwandu hwese hwema sensors akabatana, zvisinei, haungapfuure 128 sensors.
Anosvika mana anorongeka maalarm threshold anowanikwa kune yega sensor. Kune bhinari kutapurirana kwearamu kune anosvika makumi matatu nembiri relays ane anogona-yemahara shanduko-pamusoro pekubata uye anosvika makumi mapfumbamwe nenhanhatu masaini relay.
Kugadzikana uye nyore kushanda kweiyo controller unit kunoitwa kuburikidza inonzwisisika menyu chimiro.
Nhamba yezvikamu zvakabatanidzwa zvinogonesa kuzadzikiswa kwezvinhu zvakasiyana-siyana muhutano hwekuyera gasi. Configuration inofambiswa nemenu kuburikidza nekeypad. Nekukurumidza uye nyore kugadzirisa, unogona kushandisa PC yakavakirwa gadziriso software, inosanganisirwa muPC chishandiso.
Usati watumwa, ndapota funga nezve nhungamiro ye wiring uye kutumirwa kwehardware.

2.1 Yakajairika Modhi
Mune yakajairwa modhi, iyo gasi yekumisikidza yeanoshanda sensors inoramba ichivhoterwa uye inoratidzwa paLC kuratidzwa nenzira yekupuruzira. Uye zvakare, iyo controller unit inoramba ichizvitarisa pachayo, zvayaburitsa uye kutaurirana kune ese anoshanda ma sensors uye modules.
2.2 Alarm Modhi
Kana iyo gasi inosvika kana kupfuura iyo yakarongwa alarm pachikumbaridzo, alarm inotangwa, iyo yakapihwa alarm relay inovhurwa uye alarm ye LED (yakatsvuka yearamu 1, tsvuku tsvuku yearamu 2 + n) inotanga kupenya. Iyo set alarm inogona kuverengerwa kubva kumenyu Alarm Status.
Kana iyo gasi yakamira pazasi pechikumbaridzo chealarm uye set hysteresis, iyo alarm inogadzikiswa otomatiki. Mune latching mode, iyo alarm inofanirwa kusetwa patsva pamaoko paaramu inokonzeresa mudziyo mushure mekudonha pasi pechikumbaridzo.
Iri basa rinosungirwa kumagasi anopfuta akaonekwa necatalytic bead sensors inogadzira chiratidzo chinodonha pakunyanya kuwanda kwegasi.
2.3 Special Status Mode
Mune yakakosha mamiriro modhi kune kunonoka kuyerwa kwedivi rekushanda, asi hapana alarm yekuongorora. Iyo yakakosha chimiro inoratidzwa pachiratidziro uye inogara ichimisikidza kukanganisa relay.
Iyo controller unit inotora iyo yakakosha mamiriro apo:

zvikanganiso zveimwe kana zvimwe zvinoshanda zvinoshandiswa zvinoitika,
kuvhiya kunotanga mushure mekudzoka kwevoltage (simba),

iyo sevhisi modhi inogadziriswa nemushandisi,
mushandisi anoverenga kana kushandura paramita,
alarm kana kuti signal relay inodhindwa nemaoko mualarm status menyu kana kuburikidza nedigital inputs.

2.3.1 Fault Mode
Kana iyo controller unit inoona kutaurirana kwakashata kweiyo inoshanda sensor kana module, kana kana chiratidzo cheanalog chiri kunze kweiyo inotenderwa renji (< 3.0 mA> 21.2 mA), kana kana paine zvikanganiso zvemukati zvebasa zvinouya kubva kuzvidzora modules incl. murindiri uye voltage control, iyo yakapihwa kukanganisa relay inoiswa uye kukanganisa kwe LED kunotanga kupenya.
Iko kukanganisa kunoratidzwa mune menyu Error Status mune yakajeka mavara. Mushure mekubviswa kwechikonzero, meseji yekukanganisa inofanirwa kubvumwa nemaoko mune menyu Error Status.
2.3.2 Restart Mode (Kudziya-Kushanda)
Gasi rekuona ma sensors anoda kumhanyisa-munguva, kusvika iyo kemikari process ye sensor inosvika yakagadzikana mamiriro. Munguva ino yekumhanya-munguva iyo sensor siginecha inogona kutungamira kune kusingadiwe kuburitswa kwepseudo alarm.
Zvichienderana nemhando dze sensor dzakabatana, iyo yakareba nguva yekudziya-yepamusoro inofanirwa kuiswa senge poweron nguva mune controller.
Iri simba-panguva rinotangwa pane controller unit mushure mekuchinja magetsi uye / kana mushure mekudzoka kwevol.tage.
Nepo nguva ino iri kupera, gasi controller unit hairatidze chero hutsika uye haiite chero maalarm; iyo controller system haisati yagadzirira kushandiswa.
Iyo simba-pachimiro inoitika pamutsetse wekutanga wekutanga menyu.
2.3.3 Service Mode
Iyi nzira yekushanda inosanganisira kutumwa, kuenzanisa, kuedza, kugadzirisa uye kubvisa.
Iyo sevhisi modhi inogona kugoneswa kune imwechete sensor, yeboka rema sensors pamwe neye yakazara system. Mune inoshanda sevhisi modhi yakamirira maalarm emidziyo inobatwa inobatwa, asi maalarm matsva anodzvanywa.
2.3.4 UPS Kushanda
The supply voltage inotariswa mumamodhi ese.
Kana wasvika pabhatiri voltage mune simba pack, iyo UPS basa re controller unit inogoneswa uye bhatiri rakabatana rinochajwa.
Kana simba rikakundikana, bhatiri rinoputikatage inodonha pasi uye inogadzira iyo meseji yekutadza simba.
At empty battery voltage, bhatiri rakaparadzaniswa kubva kudunhu (basa rekudzivirira kwakadzika kwekudzivirira).
Kana simba racho radzorerwa, pachava nekudzoka otomatiki kune yekuchaja mode.
Hapana zvigadziriso uye saka hapana paramita inodiwa kune iyo UPS mashandiro.

Wiring kugadzirisa

Operation

Iyo yakazara gadziriso uye sevhisi inogadzirwa kuburikidza nekiyipad mushandisi interface pamwe neLC kuratidza skrini. Chengetedzo inopihwa kuburikidza nenhanho nhatu dzepassword kupesana nekupindira kusingatenderwe.

4.1 Basa remakiyi uye maLED pane keypad

	Inobuda purogiramu, inodzokera kune yakapfuura menyu level.
	Inopinda ma submenu, uye inochengetedza parameter marongero.
	Inokwira kumusoro & pasi mukati memenu, inoshandura kukosha.
	Inofambisa chinzvimbo checursor.

Chiedza che LED chitsvuku: Inopenya kana alarm imwe kana anopfuura ari kushanda.
LED yakasviba tsvuku: Inopenya kana alarm mbiri uye maaramu epamusoro pekutanga ari kushanda.
LED yero: Inopenya pane system kana sensor kutadza kana zuva rekugadzirisa rakapfuura kana muvoltage-yemahara mamiriro ane sarudzo simba kutadza kupenya mwenje.
LED yegirini: Simba re LED

	Vhura hwindo remenu raunoda. Kodhi yekupinda ndima inovhura yega, kana pasina kodhi inotenderwa.
Mushure mekuisa kodhi inoshanda iyo cursor inosvetukira pachikamu chekutanga chinoshandurwa.
	Sunda chitubu pachikamu chenzvimbo, chinofanira kuchinjwa.
	Sunda chitubu pachikamu chenzvimbo, chinofanira kuchinjwa.
	Sevha kukosha kwachinja, simbisa kuchengetedza (ENTER).
	Kanzura kuchengetedza / kuvhara kugadzirisa / dzokera kune inotevera yepamusoro menyu nhanho (ESCAPE basa).

4.3 Code Levels
Zvinoenderana nemirairo yenyika uye yepasirese zviyero zvegasi yambiro masisitimu, zvese zvinopinda uye shanduko zvinodzivirirwa nenhamba ine manhamba kodhi (= password) pakupindira kusingatenderwe. Iwo mahwindo emameseji emamiriro emamiriro uye zviyero zvekuyera zvinoonekwa pasina kuisa kodhi.
Kuburitswa kwechiyero chekodhi kunodzimwa kana pasina bhatani rinosundirwa mukati memaminitsi gumi nemashanu.
Iwo macode mazinga akaiswa muhurongwa hwekukosha:
Priority 1 ine yepamusoro pekutanga.
Chinonyanya kukosha 1: (kodhi 5468, isingachinji)
Code level yekutanga 1 inoitirwa kuti sevhisi tekinoroji yemuisi achinje maparamita uye seti-mapoinzi. Iyi pasiwedhi inobvumira kushanda pane zvese zvigadziriso. Kuvhura iyo parameter menyu unofanirwa kutanga wamisa iyo sevhisi modhi mushure mekuburitswa kwekodhi.
Chinonyanya kukosha 2: (kodhi 4009, isingachinji)
Iine kodhi nhanho 2, zvinokwanisika kukiya / kuvhura transmitters kwenguva pfupi. Iyi password inongopihwa kumushandisi wekupedzisira neaisimi mumamiriro ezvinhu edambudziko. Kuti uvhare / uvhure masensa iwe unofanirwa kutanga wamisa iyo sevhisi modhi mushure mekuburitswa kwekodhi.

Chekutanga 3: (code 4321, inogadziriswa mu menyu yekugadzirisa ruzivo)
Inongoitirwa kugadzirisa zuva rekugadzirisa. Kazhinji iyo kodhi inongozivikanwa chete nenyanzvi yebasa iyo yakapedzisira kuishandura sezvo inogona kuchinjwa yega kuburikidza nekutanga 1.
Chekutanga 4: (password 1234) (code haichinjike)
Code level yekutanga 4 inobvumira mushandisi:

kubvuma kukanganisa,
kuseta zuva nenguva,
kugadzirisa uye kushandisa iyo data logger sarudzo, mushure mekushandiswa kweiyo oparesheni modhi "Service Mode":

kuverenga ese parameters,
kushanda nemaoko bvunzo basa rearamu relays (inoshanda bvunzo yemayuniti akabatana),
kuti ushande nemaoko bvunzo basa reanalog zvinobuda (inoshanda bvunzo yemayuniti akabatana).

Menu Overview

Menu oparesheni inoitwa kuburikidza neyakajeka, intuitive uye inonzwisisika menyu chimiro. Menyu yekushandisa ine mazinga anotevera:

Kutanga menyu ine chiratidzo cherudzi rwechishandiso kana pasina MP yakanyoreswa, zvikasadaro kupururudza kuratidzwa kwegasi kuomeswa kweese akanyoreswa sensors mu5-second intervals. Kana maaramu ari kushanda, chete kukosha kwema sensors parizvino mune alarm mamiriro anoratidzwa.

Main menu
Submenu 1 kusvika ku3

5.1 Fault Management

Iyo yakabatanidzwa yekutadza manejimendi inorekodha yekutanga 100 kukanganisa ine zuva uye nguva stamps mune menyu "System Errors". Pamusoro pezvo rekodhi yezvikanganiso inoitika mu "Error memory", iyo inogona kungoverengwa nekugadzikiswa patsva nenyanzvi yebasa A yakamirira kukanganisa inomutsa chikanganiso chechiratidzo relay. Iyo yero LED (Fault) inotanga kupenya; kukanganisa kunoratidzwa mumavara akajeka ane zuva uye nguva mune yekutanga menyu.
Kana paine kukanganisa kwe sensor yakabatana maaramu anotsanangurwa mumenyu "MP Parameter" anokwidziridzwa nekuwedzera.
5.1.1 Bvuma Mhosva
Zvinoenderana nemirairo yehunyanzvi hwekuyeresa gasi, zvikanganiso zvakaunganidzwa zvinotenderwa kubvumwa otomatiki. Iko kubvuma otomatiki kwemhosho kunogoneka chete mushure mekubvisa chikonzero!
5.1.2 Chikanganiso Memory
Menyu "Error Memory" mune main menu "System Kanganiso" inogona chete kuvhurwa kuburikidza nekodhi nhanho yekutanga 1.
Mundangariro yekukanganisa, ekutanga zana akakanganisa akaitika uye akatobvumwa mumenyu "System Error" akanyorwa kune webasa tekinoroji nenzira yakachengeteka yekutadza simba.
Chenjerera:
Ichi chiyeuchidzo chinofanirwa kugara chichiverengwa panguva yekugadzirisa, kukanganisa kwakakodzera kunofanirwa kurondwa uye kuiswa mubhuku rebasa rebasa, uye pakupedzisira ndangariro inofanira kubviswa.

5.1.3 System Messages uye Mhosho

"AP 0X Yakawandisa"	Chiratidzo chazvino pakuiswa kweanalogi> 21.2 mA
Chikonzero:	Short-circuit pakupinza analog, analog sensor isina kurongeka, kana kukanganisa.
Solution:	Tarisa tambo kune analog sensor, ita calibration, tsiva sensor.
"AP Underrange"	Chiratidzo chazvino pakuiswa kweanalog <3.0 mA
Chikonzero:	Wire break pakupinza analog, analog sensor isina kurongeka, kana kukanganisa.
Solution:	Tarisa tambo kune analog sensor, ita calibration, tsiva sensor.

Chero mudziyo une microprocessor uye kutaurirana kwedhijitari - senge misoro yedhijitari, sensor board, mamodule ekuwedzera uye kunyange controller - inoshongedzerwa neyakakura yekuzvitarisa masisitimu uye mabasa ekuongorora.
Ivo vanogonesa mhedziso dzakadzama nezve chikanganiso chinokonzera uye vanobatsira vanoisa uye vanoshanda kuti vakurumidze kuona chikonzero, uye / kana kuronga shanduko.
Mhosho idzi dzinogona kutapurirana chete kana chinongedzo chepakati (kana chishandiso) chiripo.

"DP 0X Sensor Element"	(0x8001) Sensor element kumusoro we sensor - diagnostic function report kukanganisa.
Chikonzero:	Sensor mapini akatyoka, mechaniki kana kukuvara kwemagetsi
Solution:	Shandura musoro we sensor.
"DP 0X ADC Kukanganisa"	(0x8002) Kuongorora kwe amplifier uye AD inoshandura maseketi pane yekuisa mudziyo inoshuma kukanganisa.
Chikonzero:	Mechanical kana magetsi kukuvadzwa kwe ampvatengesi
Solution:	Tsiva mudziyo.
"DP 0X Voltage”	(0x8004) Kutarisisa kwe sensor uye/kana process power supply, mudziyo unoshuma kukanganisa.
Chikonzero:	Mechanical kana kukuvara kwemagetsi kwesimba rekupa
Solution:	Eresa tension kana yanyanya kuderera, tsiva mudziyo.
"DP 0X CPU Kanganiso"	(0x8008) Kutarisisa kweiyo processor basa - inoshuma kukanganisa.
Chikonzero:	Mechanical kana magetsi kukuvadzwa kwe processor
Solution:	Tsiva mudziyo.
"DP 0x EE Kanganiso"	(0x8010) Kutarisisa kwekuchengetedza data - inoshuma kukanganisa.
Chikonzero:	Kukuvadzwa nemagetsi kwendangariro kana kukanganisa kwekugadzirisa
Solution:	Tarisa kugadzirisa, shandura mudziyo.
"DP 0X I/O Kanganiso"	(0x8020) Simba ON kana kutarisa kwemukati / kubuda kwe processor inoshuma kukanganisa.
Chikonzero:	Panguva yekutangazve, kukuvara kwemagetsi kwe processor kana yezvinhu zvedunhu
Solution:	Mirira kusvika Power On yapera, chinja mudziyo.
"DP 0X Overtemp."	(0x8040) Ambien tembiricha yakanyanya; iyo sensor inoburitsa kukosha kwekuyerwa kwenguva yakatemwa uye inochinja kune yekukanganisa mamiriro mushure me24 h.
Chikonzero:	Tembiricha yakakwira zvakanyanya
Solution:	Dzivirira mudziyo kubva kuzuva rakananga kana kutarisa mamiriro ekunze.
"DP 0X Overrange"	(0x8200) Chiratidzo che sensor element pamusoro we sensor chabuda kunze.
Chikonzero:	Sensora haina kucheneswa zvakanaka (semuenzaniso gasi rekuenzanisa risiri), yakaremara
Solution:	Recalibrate sensor, shandura iyo.
"DP 0X Underrange"	(0x8100) Chiratidzo che sensor element pamusoro we sensor chabuda kunze.
Chikonzero:	Wire break pa sensor element yekupinda, sensor drift yakawandisa, yakaremara.
Solution:	Recalibrate sensor, shandura iyo.

Mutongi anotarisa kutaurirana pakati pekukumbira nemhinduro. Kana mhinduro yakanonoka, isina kukwana kana kuti isiriyo, mutongi anoona zvikanganiso zvinotevera ozvizivisa.

"SB 0X Kukanganisa"	(0x9000) Kukanganisa kwekutaurirana kubva pakati peyuniti kuenda kuSB (sensor board)
Chikonzero:	Mutsetse webhazi wakavhiringwa kana pfupi dunhu, DP 0X yakanyoreswa kune controller, asi isina kutariswa. SB 0X yakaremara.
Solution:	Tarisa mutsetse kuSB 0X, tarisa kero yeSB kana MP paramita, tsiva sensor.
"DP 0X Kukanganisa"	(0xB000) Kukanganisa kwekutaurirana kweSB kusvika kuDP 0X sensor
Chikonzero:	Mutsetse webhazi pakati peSB nemusoro wakavhiringwa kana kupfupika kwedunhu, DP 0X yakanyoreswa pane controller, asi isina kugadzirwa paSB, isiriyo gasi rudzi, DP 0X yakaremara.
Solution:	Tarisa mutsetse kuenda kuDP 0X, tarisa sensor kero kana paramita, tsiva sensor.
"EP_06 0X Kukanganisa"	(0x9000) Kukanganisa kwekutaurirana kuEP_06 0X module (yekuwedzera module)
Chikonzero:	Mutsetse webhazi wakavhiringwa kana dunhu diki, EP_06 0X yakanyoreswa pane controller, asi isina kutariswa kana kutariswa zvisizvo, EP_06 0X module yakaremara.
Solution:	Tarisa mutsetse kuenda kuEP_06 0X, tarisa kero yemodule, tsiva module.
"Kugadziriswa"	(0x0080) Kugadziriswa kweSistimu kwakakodzera.
Chikonzero:	Zuva rekugadzirisa rakapfuura.
Solution:	Ita kugadzirisa.
"DP XX yakakiyiwa" "AP XX yakavharwa"	Iyi MP yekupinda yakavharwa (MP iripo panyama, asi yakavharwa ne mushandisi)
Chikonzero:	Operator kupindira.
Solution:	Bvisa chinokonzeresa kukanganisa uye wozovhura MP.
"UPS Error"	(0x8001) UPS haishande nemazvo, inogona kusaina chete neGC.
Chikonzero:	Yakakanganisika UPS - yakakwira zvakanyanya kana yakaderera vhoriyamutage
Solution:	Tsiva UPS.
“Simba Kukundikana”	(0x8004) inogona kusaina chete neGC.
Chikonzero:	Kukundikana kwesimba kana fuse yakagumburwa.
Solution:	Tarisa magetsi kana fuse.
"XXX FC: 0xXXXX"	Zvinoitika, kana paine zvikanganiso zvakawanda kubva pane imwe yekuyeresa.
Chikonzero:	Zvikonzero zvakawanda
Solution:	Ona zvikanganiso chaizvo.

5.2 Status Alarm
Kuratidzwa kwemaaramu akamirira parizvino mumavara asina kujeka mukurongeka kwekusvika kwawo. Iwo chete mapoinzi ekuyeresa anoratidzwa, uko kana alarm imwe chete inoshanda. Iwo maalarm anogadzirwa kungave mune controller (alarm) kana zvakananga pane saiti mune sensor / module (yenzvimbo alarm).
Kupindira kunogoneka muchinhu ichi chemenu chete nekuda kwekubvuma kwelatching alarm.
Maaramu akamirira haagone kubvumwa.

Symbol	Tsanangudzo	Function
AP X	Nhamba Yekuyeresa	Analogi yekuyera poindi X = 1 - 32, apo alarm yakamirira.
DP X	Nhamba Yekuyeresa	Digital yekuyera point X = 1 - 96, apo alarm yakamirira.
'A1 ''A1	Alarm status	'A1 = Aramu yemunharaunda 1 inoshanda (yakagadzirwa mu sensor / module) A1 = Alarm 1 inoshanda (inogadzirwa mukati mekutonga)

5.3 Relay Status
Kuverenga mamiriro azvino ealarm uye masaini relay.
Iko kushanda kwebhuku (test function) yearamu uye chiratidzo chekudzoka kunoitwa mumenyu Parameters.5.4 Menyu Kuyera Maitiro
Mune iyi menyu, chiratidziro chinoratidza kukosha kwekuyera nerudzi rwegasi uye unit. Kana kuongororwa kwearamu kuchitsanangurwa kuburikidza neavhareji, chiratidziro chinoratidza kukosha kwazvino (C) uye kuwedzera kukosha kwepakati (A).

Symbol	Tsanangudzo	Function
DX	Kuyerwa kukosha	Kuyerwa kukosha kubva kubhazi sensor ine MP kero ine X = 1 - 96
AX	Kuyerwa kukosha	Kuyerwa kukosha kubva kuanalog sensor pane analog yekupinda neAX = 1 - 32
CO	Gasi rudzi	Ona 4.7.3
ppm	Gasi unit	Ona 4.7.3
A	Avhareji kukosha	Arithmetic avhareji (makumi matatu akayerwa kukosha mukati menguva yuniti)
C	Ikozvino kukosha	Ikozvino kukosha kwekugadzirisa gasi
A!	Alarm	MP yakaridza alarm
#	Main. info	Mudziyo wapfuura zuva rekugadzirisa
?	ConfigError	Kugadziriswa kweMP hakuenderane
$	Local mode	Local special mode is active
Error	Mhosva MP	Kukanganisa kwekutaura, kana chiratidzo chiri kunze kwechiyero chekuyeresa
Yakakiyiwa	MP yakakiyiwa	MP yakavharwa kwechinguva nemushandisi.

Ruzivo rweConfigError runonyanya kukoshesa ruzivo rwekugadzirisa.
Ruzivo rwearamu runogara ruchiratidzwa ne "!", kunyangwe ConfigError kana ruzivo rwekugadzirisa rwuri kushanda.

5.5 Ruzivo rwekuchengetedza
Kudzora kwemaitiro ekugadzirisa anodiwa nemutemo (SIL) kana nemutengi akabatanidzwa muMutungamiriri system. Paunenge uchichinja nguva dzekugadzirisa, iwe unofanirwa kucherechedza zviri pamutemo uye zvenormative mirau uye zvinongedzo zvemugadziri! Nguva dzose mushure meizvozvo, kuenzanisa kunofanirwa kuitwa kuitira kuti shanduko iite kushanda.
Meseji yekugadzirisa sisitimu:
Pakutumwa kana mushure mekugadzirisa kwakabudirira, zuva (bhatiri rinotsigirwa) rekugadzirisa kunotevera kweiyo system yese inofanirwa kuiswa. Kana zuva iri rasvika, meseji yekuchengetedza inovhurwa.
Sensor kugadzirisa meseji:
Masensa anoda kugara achiongororwa kuti aenderane nekwakatsanangurwa chokwadi uye kuvimbika. Kuti udzivise zvinyorwa zvakaomesesa zvemanyorero, masensa anochengeta nguva yavo yekumhanya pakati penguva yekuenzanisa nguva nenguva uye zvachose. Kana iyo nguva yekumhanya kubva payekupedzisira calibration ichipfuura iyo sensor yekuchengetedza nguva yakachengetwa mu sensor, meseji yekuchengetedza inotumirwa kune yepakati control.
Iyo meseji yekugadziridza inoiswa patsva panguva yekuenzanisa uye nguva yekumhanya kubva iyo yekupedzisira calibration yakaiswa kune zero.
Kuita kwemudziyo une meseji yakamirira kugadzirisa:
Chiratidzo chekugadzirisa chinogona kuve ORed kune yega yega inoshanda relays mune menyu Relay Parameters. Nenzira iyi, imwe kana kupfuura relays inogona kushandiswa kana ichichengetedza (ona 4.8.2.9).
Kana iri meseji yakamirira kugadzirisa, foni kwete. yekambani yebasa inoonekwa mumenyu huru pane iyo nguva / zuva ruzivo uye iyo yero LED pachiratidziro inotanga kupenya.
Mharidzo yekugadzirisa inogona chete kucheneswa nekubvisa chikonzero - kushandura zuva rekugadzirisa kana kuenzanisa kana kutsiva ma sensor.
Kuti usiyanise pakati peiyo mameseji ekugadzirisa sensor uye meseji yekugadziridza system uye kuti uwane nekukurumidza kugoverwa kwemasevhisi anoshanda, iyo yakayerwa kukosha muchinhu chemenu Measured Values inowana yekugadziridza prefix "#".
Sekuwedzera ruzivo, hwindo rakaparadzana rinoratidza nguva (mumazuva) apo sensor inotevera inofanirwa kugadziriswa. Kana masensa akati wandei akabatana, iyo ipfupi nguva inogara ichiratidzwa.
Mune submenu, unogona kupururudza kuburikidza nekuratidzwa kweese anoshanda ekuyeresa mapoinzi kuti uone ma sensors uko kugadziridzwa kwakakodzera munguva pfupi.
Nhamba huru inomiririrwa mazuva 889 (vhiki 127 / makore 2.5). Kana iyo inotevera gadziriso inokodzera mune yakato rebesa nguva, iyo nguva yekuratidzira ichiri yakaganhurirwa kumazuva 889.5.6 Ratidza Parameter
Mune menyu Ratidza Parameter iwe unogona kuwana iyo yakajairika, chengetedzo isina basa paramita yegasi controller.
Aya ma parameter anogona kuchinjwa panguva yekushanda maitiro emutongi. 5.6.1 Software Shanduro

Symbol	Tsanangudzo	Function
XXXXX YYYYY	Software Version yezviratidziro zveSoftware Vhezheni yebhodhi rekutanga	XXXXX Software Version YYYYY Software Version

5.6.2 Mutauro

Symbol	Tsanangudzo	Default	Function
Chirungu	Mutauro	Chirungu	Chirungu USA English German French

5.6.3 Nhamba Yenhare Yebasa

Nhare yefoni yebasa. inogona kuiswa yega mune inotevera menyu.

Symbol	Tsanangudzo	Default	Function
	Nhare yefoni.		Input yefoni yebasa remunhu no.

5.6.4 Nguva yeSistimu, Zuva reSistimu

Kupinza uye kugadzirisa nguva uye zuva. Kusarudzwa kwenguva uye chimiro chezuva

Symbol	Tsanangudzo	Default	Function
EU	Time format	EU	EU = Kuratidzwa kwenguva uye zuva muEU fomati US = Ratidza yenguva uye zuva muUS fomati
hh.mm.ss	Nguva		hh.mm.ss = Mapindiro enguva chaiyo (mafomati eEU) hh.mm.ss pm = Mapindiro enguva chaiyo (US fomati)
TT.MM.JJ	Date		TT.MM.JJ = Kuiswa kwezuva chairo (fomu reEU) MM.TT.JJ = Kuiswa kwezuva chairo (fomu reUS)

5.6.5 Nguva Yekukanganisa Kunonoka

Symbol	Tsanangudzo	Default	Function
s	Kunonoka	120s	Tsanangudzo yenguva yekunonoka kana kukanganisa kwekutaurirana kunoratidzwa pachiratidziro. (Kunonoka pakubuda kwekukanganisa hakubvumidzwe, saka hakushandiswe.)

5.6.6 X Bhazi Muranda Kero

(iripo chete, kana X Bhazi basa riripo)

Symbol	Tsanangudzo	Default	Function
Kero	Kero yemuranda paX Bhazi interface	1	Kupinza kero yemuranda paX bhazi. Mukuwedzera kune kero, sarudzo inowanikwa inooneka. Parizvino chete Modbus iripo (teerera kune mamwe magwaro eiyo protocol)

5.7 Paramende
Mune menyu Parameters iwe unogona kuwana iyo parameter mabasa egasi controller.

5.7.1 Ratidza Parameter
Sevhisi uye basa rekugadzirisa harifanirwe kuitwa kana gasi rinotonga riri munzira yekuyeresa nekuti haina chokwadi chekuti nguva dzese dzekupindura uye mabasa anogona kucherechedzwa nemazvo.
Kuti uite calibration uye sevhisi yebasa, iwe unofanirwa kutanga waisa iyo yakakosha mamiriro modhi pane controller. Ipapo chete iwe unobvumidzwa kushandura iyo yakachengeteka ine chekuita paramita. Iyo yakakosha yekushandisa mode inogadziriswa, pakati pevamwe, basa reSevhisi ON.
Zvimwe zvimiro zvemenu zvinhu zvinongowanikwa muSevhisi ON state. Iyo Sevhisi ON mamiriro anoiswa patsva kune yakajairwa maitiro ekuita otomatiki maminetsi gumi nemashanu mushure mekupedzisira kiyi yekudzvanya kana nemaoko mumenyu nemushandisi.
Sensors haigone kuchinjirwa kuita "special mode" kubva kune controller. Inogona chete kuitwa zvakananga pane sensor uchishandisa chishandiso. Sensors mu "special mode" haina kubatanidzwa mukuongororwa kwearamu.

Symbol	Tsanangudzo	Default	Function
DZIMA	Service	DZIMA	OFF = Hapana kuverenga uye kuchinja kwemiganhu. ON = Mutongi mune Yakakosha mamiriro modhi, paramita inogona kuverengwa nekushandurwa.

5.7.2 Menu Relay Parameter
Kuverenga uye shanduko yemaparamita zvakasiyana kune yega relay.5.7.2.1 Relay Mode
Tsanangudzo yeiyo relay mode

Symbol	Tsanangudzo	Default	Function
Used	Mode	Used	Inoshandiswa = Relay yakanyoreswa pane controller uye inogona kushandiswa Haina Kushandiswa = Relay haina kunyoreswa pane controller

5.7.2.2 Relay Operation Mode
Tsanangudzo yeiyo relay operation mode
Mazwi ekugonesa / de-energized echinhu ichi anobva kumashoko akavhurika-dunhu uye akavharika-yedunhu musimboti anoshandiswa kune ekuchengetedza maseketi. Pano, zvisinei, kwete relay contact circuit inoreva (sekuchinja kwekubatana, zvingasarudzwa zviripo mumitemo miviri), asi kushandiswa kweiyo relay coil.
Iwo ma LED akabatanidzwa kune ma modules anoratidza maviri nyika mukuenzanisa. (LED inodzima -> relay de-energized)

Symbol	Tsanangudzo	Default	Function
De-energ.	Mode	De-energ.	De-energ. = Relay (uye LED) de-energized, kana pasina alarm inoshanda Inosimbiswa = Relay (uye LED) yakasimbiswa zvachose, kana pasina alarm inoshanda

5.7.2.3 Relay Function Static / Flash
Tsanangudzo yebasa relay
Basa re "Flashing" rinomiririra sarudzo yekubatanidza kune yambiro midziyo yekuvandudza kuoneka. Kana "Flashing" yakasetwa, iyi haifanire kushandiswa seyakachengeteka yekubuda dunhu zvakare.
Musanganiswa werelay modhi inopihwa simba nekupenya kwekushanda haina musoro uye saka inodzvinyirirwa.

Symbol	Tsanangudzo	Default	Function
ON	Function	ON	ON = Relay basa rinopenya paalarm (= nguva yakatarwa 1 s) kufambisa / kuputsa = 1: 1 OFF = Relay basa rakamira ON paaramu

5.7.2.4 Alarm Trigger Quantity
Mune mamwe maapplication zvinodikanwa kuti relay inochinja chete pa nth alarm. Pano iwe unogona kuseta nhamba yemaalarm anodiwa pakuita relay tripping.

Symbol	Tsanangudzo	Default	Function
Quantity	Function	1	Chete kana huwandu uhu hwasvikwa, relay nzendo.

5.7.2.5 Nyanga Basa (isina kuchengeteka inobuda dunhu nekuti resettable)
Iyo nyanga basa inoonekwa seyakashanda kana inokwana imwe yeaya maviri paramita (nguva kana mugove kune yedhijitari yekuisa) yakaiswa. Iyo nyanga basa inochengetedza mashandiro ayo kunyangwe maalarm mune latching mode.

Symbol	Tsanangudzo	Default	Function
Kudzokorora	Reset mode	0	0 = Reset relay mushure menguva yapera kuburikidza neDI (yekunze) kana nemabhatani 1 = Mushure mekugadzirisazve relay, nguva inotanga. Pakupera kwenguva yakatarwa, relay inoshandiswa zvakare (kudzokorora basa).
Nguva		120	Pinda nguva ye otomatiki reset basa kana kudzokorora basa mus 0 = hapana reset basa
DI		0	Assignment, iyo inopinza yedhijitari inogadzirisa relay.

Horn function inogadziriswazve:
Iyo nyanga yakabatidzwa inogona kusetwa zvachose neiri basa.
Aya anotevera mikana yekubvuma anowanikwa kune alarm relay sehorn relay:

Nekudzvanya bhatani rekuruboshwe (ESC). Inowanikwa chete mukutanga menyu.
Kugadzirisa otomatiki pakupera kwenguva yakatarwa (inoshanda, kana yakakosha> 0).
Nekusundidzira kwekunze (kugoverwa kweiyo yakakodzera dhijitari yekuisa DI: 1-n).

Nekuda kwekugadziriswa kwekuvhota, mabhatani ekunze anofanirwa kudzvanywa kwemasekonzi mashoma maitiro asati aitika.
Mushure mekubudirira kubvuma nyanga inoramba yakagadziridzwa zvachose kusvikira maaramu ese akapihwa eiyi relay basa asisashande zvakare.
Ipapo ndipo painotangwa patsva kana paine alarm.

Bvuma kurira kwenyanga5.7.2.5 Nyanga Basa (kwete yakachengeteka goho redunhu nekuti resettable) (Enderero mberi)
Kudzokororwa kwenyanga relay
Mushure mekunge alarm yaridzwa, nyanga icharamba ichishanda kusvika chiito chekugadzirisa chaitwa. Mushure mekubvuma nyanga relay/s (kudzvanya bhatani kana kuburikidza nekunze kwekuisa) inotangisa nguva. Kana nguva ino yapera uye alarm ichiri kushanda, relay inoiswa zvakare.
Iyi nzira inodzokororwa nekusingaperi chero bedzi iyo alarm yakabatana inoramba ichishanda.5.7.2.6 Kupfuura Kwekunze kweAlarm / Signal Relay kuburikidza neDI
Manual mashandiro earamu relays kuburikidza neDI haikonzeri "special mode", sezvo uku kuri kuita nemaune uye kwakagadziriswa. Kushandiswa kwepamusoro kunofanira kushandiswa nekuchenjerera, kunyanya basa rekugadzirisa "external OFF".
Kugoverwa kwedhijitari yekupinda (DI) yekunze yekubatidza nekudzima kwearamu relay.
Iri basa rinonyanya kukosha kune gasi alarm.
Kana Zvekunze ON uye Zvekunze OFF zvakagadziridzwa panguva imwe chete kune imwechete relay uye ese ari maviri ari kushanda panguva imwe chete, saka mune ino mamiriro, Chekunze OFF murairo chete unoitwa.
Mune iyi modhi, zvakare, iyo relays inoshanda ichiremekedza parameter marongero "Static / Flash" uye "anergized / de-energized".

Symbol	Tsanangudzo	Default	Function
↗ DI 0	External ON	0	Chero bedzi DI 1-X yakavharwa, relay switch ON
↘ DI 0	External OFF	0	Chero bedzi DI 1- X yakavharwa, relay inodzima.

5.7.2.7 Kunze Kupfuura kweAlarm / Signal Relay kuburikidza neDI
Tsanangudzo ye switch-on uye switch-off kunonoka kweiyo relays.
Kana iyo latching modhi yakaseterwa kune iyi relay, iyo yakatarisana switch-off kunonoka haina mhedzisiro.

Symbol	Tsanangudzo	Default	Function
0 p	Switch-ON Kunonoka Nguva	0	Alarm / Signal Relay inongoitwa pakupera kwenguva yakatsanangurwa. 0 sec. = Hapana kunonoka
0 p	Switch-OFF Kunonoka Nguva	0	Alarm / Signal Relay inongomiswa pakupera kwenguva yakatsanangurwa. 0 sec. = Hapana kunonoka

5.7.2.8 KANA Kushanda kweFault to Alarm / Signal Relay
Inogonesa kana kudzima iyo Fault OR kushanda kweazvino alarm / siginecha relay.
Kana iyo OR mashandiro eiyi relay akaiswa kuti ashande = 1, zvese zvinokanganisa zvemudziyo zvinomutsa zvabuda mukuwedzera kune maaramu masaini.
Mukuita, iyi ORing ichashandiswa kana, semuenzanisoampLe, mafeni anofanira kumhanya kana mwenje yekuyambira inofanirwa kuvhurwa kana mudziyo ukasashanda, sezvo iwo meseji yekukanganisa yepakati control isingatariswe zvachose.
Cherechedza:
Kunze zvikanganiso zvese zvekuyera nzvimbo nekuti maMP anogona kupihwa kune imwe neimwe alarm zvakasiyana mune menyu MP Parameters. Kusarudzika uku kunoshandiswa kugadzira siginecha yakanangana nenharaunda kana paine kukanganisa kweMP, izvo zvisingafanire kukanganisa dzimwe nzvimbo.

Symbol	Tsanangudzo	Default	Function
0	Hapana basa	0	Alarm uye/kana relay relay haina kukanganiswa kana chikanganiso chemudziyo chikaitika.
1	Activated assignment	0	Alarm uye/kana relay relay inobatidzwa kana kukanganisa kwemudziyo kuchiitika.

5.7.2.9 KANA Kushanda Kwekuchengetedza kuAlarm / Signal Relay

Inogonesa kana kudzima iyo Maintenance OR kushanda kweazvino alarm / chiratidzo chekudzoka.
Kana iyo OR kushanda kweiyi relay kwakaiswa kuita = 1, iyo inobuda ichaitwa mukuwedzera kune maaramu masaini kana kamwechete meseji yekuchengetedza yakamirira.
Mukuita, iyi ORing ichashandiswa kana, semuenzanisoampLe, mafeni anofanirwa kumhanya kana iyo sensor kurongeka kusingazovimbiswe zvakare nekuda kwekushaikwa calibration (nekudaro yakamirira meseji yekugadzirisa) kana mwenje yenyevero inofanirwa kuvhurwa, sezvo ruzivo rwekuchengetedza rwepakati control rusingatariswe zvachose.
Cherechedza:
Kugadzirisazve meseji yakagadziriswa yekugadziridza inogoneka chete nekugadzirisa ma sensors kana nekudzima iyi OR basa.

Symbol	Tsanangudzo	Default	Function
0	Hapana basa	0	Alarm uye/kana relay relay haina kukanganiswa kana meseji yekuchengetedza ikaitika.
1	Activated assignment	0	Alarm uye/kana relay relay inobatidzwa kana meseji yekugadzirisa ikaitika.

5.7.3 Menyu MP Parameters
Zvekuverenga uye kushandura kuyera nzvimbo paramita yebhazi rega rega uye analog sensor kusanganisira kunyoreswa kweMP uye kupihwa kwearamu relay. 5.7.3.1 Activate – Deactivate MP

Deactivation inovhara iyo yakanyoreswa / isina kunyoreswa sensor pasi mukushanda kwayo, zvinoreva kuti hapana alarm kana meseji yekukanganisa panguva ino yekuyera. Maaramu aripo uye kukanganisa zvinobviswa nekudzima. Deactivated sensors haibudise meseji yekukanganisa.

Symbol	Tsanangudzo	Default	Function
active	MP Mode	Kwete kushanda	inoshanda = Kuyeresa poindi yakabatiswa pane controller. kwete kushanda = Kuyeresa poindi isina kuvhurwa pane controller.

5.7.3.2 Kiya kana kiinura MP

Mune yekanguva Lock Mode, basa rema sensors akanyoreswa rinoiswa kunze kwebasa, izvo zvinoreva kuti hapana alarm kana meseji yekukanganisa panguva ino yekuyera. Maaramu aripo uye zvikanganiso zvinobviswa nekukiya. Kana imwe sensor yakavharwa mukushanda kwayo, iyo meseji yekukanganisa inomiswa mushure mekupera kweiyo yemukati kukanganisa kunonoka nguva, iyo yero kukanganisa LED iri kupenya uye meseji inoonekwa mumenyu System Errors.

Symbol	Tsanangudzo	Default	Function
kukiyiwa	Lock muoti	kukiyiwa	kuvhurwa = MP yemahara, yakajairika kushanda yakakiyiwa = MP yakavharwa, SSM (collective fault message) inoshanda

5.7.3.3 Kusarudzwa Gasi Rudzi neYuniti

Kusarudzwa kweinodiwa uye yakabatana gasi sensor rudzi (kubatanidzwa kunogoneka sedhijitari sensor cartridge Basic, Premium kana Heavy Duty).
Sarudzo ine ruzivo rwese rwunodiwa kune controller, uye inoshandiswawo pakuenzanisa iyo chaiyo, data yedhijitari nezvirongwa.
Ichi chimiro chinowedzera mushandisi uye chengetedzo yekushandisa.
Kune yekupinda inowanikwa parudzi rwegasi kune yega yega unit.

Sensor	Internal type	Kuyera range	Unit
Ammonia EC 100	E1125-A	0-100	ppm
Ammonia EC 300	E1125-B	0-300	ppm
Ammonia EC 1000	E1125-D	0-1000	ppm
Ammonia SC 1000	S2125-C	0-1000	ppm
Ammonia EC 5000	E1125-E	0-5000	ppm
Ammonia SC 10000	S2125-F	0-10000	ppm
Ammonia P LEL	P3408-A	0-100	% LEL
CO2 IR 20000	I1164-C	0-2	% Vol
CO2 IR 50000	I1164-B	0-5	% Vol
HCFC R123 SC 2000	S2064-01-A	0-2000	ppm
HFC R404A, R507 SC 2000	S2080	0-2000	ppm
HFC R134a SC 2000	S2077	0-2000	ppm
HC R290 / Propane P 5000	P3480-A	0-5000	ppm

5.7.3.4 Kuyera Range Tsanangudzo

Chiyero chekuyera chinofanirwa kuchinjirwa kune iyo inoshanda renji yeyakabatana gasi sensor.
Kuti uwedzere kutonga nemuisi, marongero ari mu controller anofanirwa kuenderana nemasensa anoshandiswa. Kana iwo marudzi egasi uye / kana kuyerwa kwemarenji e sensor asingabvumirane nemaseting emutongi, iko kukanganisa "EEPROM / gadziriso kukanganisa" inogadzirwa, uye meseji yekukanganisa inogadzirwa.
Iyo mhando inobatawo kuratidzwa kweakayerwa kukosha, alarm zvikumbaridzo uye hysteresis. Zvekuyera marengenzi <10 nzvimbo nhatu dzedesimali, <100 nzvimbo mbiri dzegumi, <1000 imwe nzvimbo yedesimali inoratidzwa. Yekuyera mitsara => 1000, chiratidziro chisina nzvimbo yedesimali. Kugadziriswa uye kurongeka kwekuverenga hakukanganiswe neakasiyana marenji ekuyera.

5.7.3.5 Threshold / Hysteresis
Kune imwe neimwe yekuyeresa poindi mana aramu zvikumbaridzo zviripo kune yemahara tsananguro. Kana iyo gasi yekumisikidza yakakwira kupfuura yakatarwa alarm chikumbaridzo, iyo inosanganisirwa alarm inovhurwa. Kana iyo gasi yakamira pazasi pechikumbaridzo chealarm inosanganisira hysteresis alarm inodzoserwa zvakare.
Mune modhi "Alarm pakudonha" alarm inoenderana inoiswa kana ichidonha pasi peyakaiswa alarm chikumbaridzo uye reset zvakare kana yadarika chikumbaridzo pamwe nehysteresis. Chiratidziro chinoenderana neseti yekuyera renji: ona 4.8.3.4. Zvikumbaridzo zvealarm zvisina kushandiswa zvinofanirwa kutsanangurwa pakuyeresa nhanho yekupedzisira, kuitira kudzivirira maaramu asingadiwe. Maaramu epamusoro-soro anovhura otomatiki maaramu epazasi.

Symbol	Tsanangudzo	Default	Function	Symbol
A	Evaluation	A	AC	A = Alarm ongororo ine avhareji kukosha kweMP C = Alarm ongororo ine kukosha kwazvino kweMP
80 ppm	Alarm chikumbaridzo	40 80 100 120 15	Chikumbaridzo 1 Chikumbaridzo 2 Chikumbaridzo 3 Chikumbaridzo 4 Hysteresis	Gas concentration > Threshold 1 = Alarm 1 Gas concentration > Threshold 2 = Alarm 2 Gas concentration > Threshold 3 = Alarm 3 Gas concentration > Threshold 4 = Alarm 4 Gas concentration < (Threshold X -Hysteresis) = Alarm X OFF
↗		↗		↗ = Alarm kusunungurwa pakuwedzera kukoshesa ↘ = Kuburitswa kwearamu pakudonha kwemazinga

5.7.3.6 Kunonoka kwe alarm

Tsanangudzo yekunonoka nguva yealarm ON uye/kana alarm OFF. Iko kunonoka kunoshanda kune ese maalarm eMP, kwete neavhareji kukosha kwepamusoro, ona 5.7.3.7.

Symbol	Tsanangudzo	Default	Function
0 p	CV Alarm ON kunonoka	0	Gasi rekuisa > Threshold: Alarm inongoitwa pakupera kwenguva yakatarwa (sec.). 0 sec. = Hapana kunonoka
0 p	CV Alarm OFF kunonoka	0	Gas concentration < Threshold: Alarm inongodzimwa pakupera kwenguva yakatarwa (sec.). 0 sec. = Hapana kunonoka

5.7.3.7 Latching Mode Yakagoverwa Alarm

Mune iyi menyu iwe unogona kutsanangura, ndeapi maaramu anofanirwa kushanda mune latching mode.

Symbol	Tsanangudzo	Default	Function
Alamu – 1 2 3 4 SBH – 0 0 0 0	Kubata MP	0 0 0 0	0 = Hapana latching 1 = Kubata

5.7.3.8 MP Mhosva Yakapihwa alarm

Mune iyi menyu iwe unogona kutsanangura, ndeapi maaramu anofanirwa kuitwa nekukanganisa pane yekuyeresa.

Symbol	Tsanangudzo	Default	Function
Alamu – 1 2 3 4 SBH – 0 0 0 0	Mhosva MP	1 1 0 0	0 = Alarm haina ON pane MP kukanganisa 1 = Alarm ON pane MP kukanganisa

5.7.3.9
Alarm Yakapihwa kuAlarm Relay

Imwe neimwe yearamu ina inogona kupihwa kune chero iripo yemuviri alarm relay 1 kusvika 32 kana sign relay R1 kusvika R96. Maaramu asina kushandiswa haana kupihwa kune alarm relay.

Symbol	Tsanangudzo	Default	Function
0	A1 A2 A3 A4	0 0 0 0	RX = Kugoverwa kwemaalarm A1 - A4 kune iyo chiratidzo inodzosera R1-R96 X = Kugovewa kwearamu A1 - A4 kune iyo alarm inodzosera 1-32

5.7.3.10 MP Chiratidzo Chakapiwa kune Analogi Kubuda

Iyo yekuyera poindi chiratidzo (ikozvino kana avhareji kukosha) inogona kupihwa kune imwe yeakawanda. 16 analog zvabuda. Basa rimwechete kune zvakasiyana-siyana zvinobuda (8) rinogadzira kudzokorora kunoshanda. Izvi zvinowanzo shandiswa kudzora zvigadziriso zviri kure zvakafanana (kupa fan mukamuri yepasi, mafeni ekupedza padenga).
Kana migove yakati wandei ichiitwa kune imwe analog inobuda, chiratidzo chinobuda chinobuda ASISINA ruzivo rwekukanganisa. Zvinofanira kucherechedzwa kuti musanganiswa wemhando dzakasiyana dzegasi kazhinji hazvina musoro. Panyaya yebasa rimwe chete = yakawedzera analog kubuda 1: 1, chiratidzo chinobuda NEruzivo rwekukanganisa.
Analogi yakabuda onawo: 5.7.4.4.

Symbol	Tsanangudzo	Default	Function
xy	Analog Output	xy	x = MP Chiratidzo chinopihwa analog outputx (inomutsa kudzora kubuda -> chiratidzo chinogona kushandiswa) y = MP Chiratidzo chakapihwa kuanalog kubuda (inomutsa kudzora kubuda -> chiratidzo chinogona kushandiswa) 0 = MP Signal haina kupihwa kune chero analog kubuda kana kusaburitswa muSystem Parameters (hapana inoshanda inobuda kutonga)

5.7.4 Menu System Parameters

5.7.4.1 Ruzivo rweSystem

Symbol	Tsanangudzo	Default	Function
XXXX	Siriyero nhamba	0	Siriyero nhamba
XX.XX.XX	Zuva reKugadzirwa	0	Zuva rekugadzirwa

5.7.4.2 Nguva Yekuchengetedza

Tsanangudzo yepfungwa yekuchengetedza inoratidzwa mu4.5.
Nguva yekugadzirisa yemutongi yakaiswa pano. Kana 0 ikaiswa, basa iri rinovharwa.

Symbol	Tsanangudzo	Default	Function
XXXX	Nguva Yekuchengetedza		Kupinda kwepakati pakati pemasevhisi maviri mumazuva

5.7.4.3 Simba Nenguva
Gasi sensors inoda kumhanyisa-munguva, kusvika iyo kemikari process ye sensor inosvika yakagadzikana mamiriro. Munguva ino yekumhanya-munguva chiratidzo chazvino chinogona kutungamira kune kusingade kukonzeresa kwepseudo alarm. Naizvozvo iyo Power On time inotangwa paGasi Controller mushure mekunge wabatidza magetsi. Ipo nguva ino iri kupera, Gasi Controller haaite maaramu kana UPS relay. Iyo Power On chimiro inoitika pamutsetse wekutanga wekutanga menyu.
Chenjerera:
Munguva yeSimba Pachikamu mutongi ari mu "Special Mode" uye haaite mamwe mabasa padivi pekutanga maitiro ekuongorora. A count-down Power On time in seconds inoratidzwa pachiratidziro.

Symbol	Tsanangudzo	Default	Function
30s	Simba Nenguva	30s	XXX = Tsanangudzo yesimba Nenguva (sec.)

5.7.4.4 Analog Output

Iyo Gasi Controller Module pamwe nemamodule ekuwedzera 1 kusvika 7 ane maviri analog mabudiro (AO) ane 4 kusvika 20 mA chiratidzo chimwe nechimwe. Chiratidzo cheimwe kana anopfuura mapoinzi ekuyeresa anogona kupihwa kune imwe neimwe yeanalogi inobuda; mune iyi kesi, chiratidzo chekutonga chinotanga kushanda uye chinobuda chiri kutariswa ikozvino. Iyo yekutarisa chiratidzo kuzvirapa uye saka haifanirwe kubvumwa. Basa racho rinoitwa mumenyu "MP Parameter" yeMP yega yega. Iyo yekuyera poindi inotumira ikozvino kukosha chiratidzo kune analog yakabuda.
Kunze kwezvikwangwani zveese akagoverwa ekuyera mapoinzi Mutongi weGasi anosarudza hushoma, huwandu kana huwandu hwepakati uye huchiendesa kune analog kubuda. Tsanangudzo, iyo yakakosha inofambiswa, inoitwa mumenyu "Analog Output X".
Kubvumidza inochinjika yemhepo vhoriyamu kudzorwa kweanomhanya-anodzorwa mota, kutsetseka kwechiratidzo chekubuda kunogona kuchinjirwa kumamiriro epa-saiti uye kusiyanisa pakati pe10 - 100%.
Seimwe nzira yekushandiswa kuburikidza nemutongi (inotsanangurwa nenhamba 1), zvinyorwa zveanalogi zvinogona kugoverwa kune zvinyorwa zveanalogi zveiyo imwechete yekuwedzera module (menu mune yekuwedzera module).
Nechinangwa ichi, iyo nhamba 10 - 100% inofanirwa kuiswa pane yekuwedzera module.

Symbol	Tsanangudzo	Default	Function
Analog Output 1	Kusarudzwa kwechiteshi		Kusarudzwa kweanalog kubuda 1-16
0 1 10-100 %	Kusarudzwa kwechiratidzo chekubuda	100 %	0 = Analog yakabuda haisi kushandiswa (saka nguva dzose de-activated response monitoring) 1 = Kushandiswa kwepanzvimbo (kusiri kushandiswa mukutonga kwepakati) Kusarudzwa kwechiratidzo chekuyerera-inobvumidzwa renji 10 - 100 % 100% gasi chiratidzo chekutonga = 20 mA 10% gasi chiratidzo chekudzora = 20 mA (yakanyanya kunzwa)
A	Kusarudzwa kwenzvimbo	A	C = Kwakabva kukosha kwazvino A = Kunobva kune avhareji kukosha CF = Kunobva kukosha kwazvino uye yakawedzera kukanganisa meseji kuAO AF = Kunobva kune avhareji kukosha uye yakawedzera kukanganisa meseji paAO
Max.	Kusarudzwa kwemaitiro ekubuda	Max.	Min. = Inoratidza hushoma kukosha kwese kupihwa MP Max. = Inoratidza kukosha kwepamusoro kwevose vakagoverwa MP Avhareji = Inoratidza kukosha kwepakati pevose vakapiwa MP

5.7.4.5 Relay Kuwandisa
Iine relay yekuwedzera tafura, zvinogoneka mu controller system kupa mamwe mabasa erelay kune alarm. Izvi zvinoenderana nekupedzisira kune imwe kuwanda kweiyo sosi alarm mamiriro ekupinda.
Iyo yekuwedzera relay inotevera aramu mamiriro ekwakabva, asi inoshandisa yayo relay paramita kubvumidza zvakasiyana zvinodiwa zvekaviri relay. Saka iyo sosi relay inogona kugadzirwa, semuenzanisoample, sebasa rekuchengetedza mu de-energized mode, asi iyo yakapetwa kaviri relay inogona kuziviswa neinopenya basa kana se nyanga basa.
Kune huwandu hunosvika makumi maviri ezvinyorwa zve IN relays uye OUT relays. Saka zvinogoneka, kune example, kuwedzera imwe relay kune vamwe gumi nemapfumbamwe kana kupeta max. 19 relay.
Muchikamu IN (mabviro), unogona kuseta relay yakagoverwa kune alarm mune menyu MP Parameter.
Muchikamu OUT (chinangwa), unogona kuisa relay inodiwa mukuwedzera.
Cherechedza:
Manual kupindira mumenyu Relay Status kana kudarika kunze ON kana KUDZIMWA nekunze DI hakuite searamu mamiriro, saka zvinongokanganisa IN relay. Kana izvi zvichidikanwawo kune OUT relay, inofanirwa kugadzirwa yakaparadzana kune yega yega OUT relay.

Number	Tsanangudzo	Default Status	Function
0-30 0-96	IN AR Relay IN SR Relay	0	0 = Basa rakadzima X = Relay X inofanirwa kuwanzwa (ruzivo sosi).
0-30 0-96	OUT AR Relay OUT SR Relay	0	0 = Basa rakadzima X = Relay X (chinangwa) inofanira kushandura pamwe chete neIN relay.

ExampLe 1:
3 relay contacts inodiwa neiyo yakafanana maitiro erelay 3, (ona kugoverwa kweiyo relay muchitsauko MP.
Parameters.)
Munopinda: 1: IN AR3 OUT AR7
Munopinda: 2: IN AR3 OUT AR8

Kana relay 3 ikavhurwa kuburikidza nearamu, inodzosera AR3, AR7 uye AR8 switch panguva imwe chete.
ExampLe 2:
2 relay contacts imwe neimwe inodiwa kubva ku3 relays (yeex. AR7, AR8, AR9).
Kupinda: 1: IN AR7 OUT AR12 (Relay 12 switches panguva imwe chete nerelay 7)
Kupinda: 2: IN AR8 OUT AR13 (Relay 13 switches panguva imwe chete nerelay 8)
Kupinda: 3: IN AR9 OUT AR14 (Relay 14 switches panguva imwe chete nerelay 9)

Izvi zvinoreva kuti relay AR7 inochinja neAR12;
AR8 ine AR13; AR9 ine AR14.
Vaviri examples inogona kusanganiswa, zvakare.

5.7.5 Kuedza Basa reAlarm uye Signal RelaysBasa rekuyedza rinoseta mudziyo wakanangwa (yakasarudzwa relay) muSpecial Mode uye inomisikidza timer inodzoreredza yakajairwa kuyerwa modhi mushure memaminitsi gumi nemashanu uye inopedza basa rekuyedza.
Naizvozvo iyo yero ye LED pane controller iri mugwaro ON kana OFF chimiro.
Iko kushanda kwekunze kweiyo relay kuburikidza neyakapihwa yedhijitari yekuisa kune yekutanga kune iyo manual test basa mune ino menyu chinhu.

Symbol	Tsanangudzo	Default	Function
AR Status	Relay Nr. X		X = 1 - 32 Sarudza alarm relay
SR Status	Relay Nr. X		X = 1 - 96 Sarudza chiratidzo chekutumira
DZIMA	Relay Status	DZIMA	Status OFF = Relay OFF (hapana gasi aramu) Mamiriro ON = Relay ON (aramu yegasi) Manual DZIMA = Relay bhuku DZIMA Manual ON = Relay bhuku ON Automatic = Relay mune otomatiki modhi

5.7.6 Muedzo Basa reAnalog Outputs
Iyi ficha inowanikwa chete muSpecial Mode.
Nebasa rekuedza iwe unogona kuisa kukosha (mu mA) iyo inofanirwa kubuda mumuviri.
Basa rekuedza kuburikidza nemutongi rinogona kushandiswa chete kana mabudiro eanalogi akadhindwa (kugadzirisa 1 yeanalogu zvabuda mumatanho ehurongwa hwechigadzirwa chakabatana, ona 5.7.4.4).Chero ruzivo, kusanganisira, asi rusina kuganhurirwa kuruzivo rwekusarudzwa kwechigadzirwa, mashandisiro acho kana mashandisiro, dhizaini yechigadzirwa, huremu, hukuru, kugona kana imwe kana chero imwe data yehunyanzvi mumanyoro echigadzirwa, tsananguro dzemakatalog, kushambadza, nezvimwewo uye ingave yakawanikwa nekunyora, nemuromo, nemagetsi, online kana kuburikidza nekudhawunirodha, inozoonekwa seine ruzivo, uye inongo sunga kana uye kusvika pamwero iwoyo, yakajeka referensi yakaitwa mukurongeka. Danfoss haigone kubvuma chero mutoro wezvikanganiso zvingangoitika mumakatalog, mabhurocha, mavhidhiyo uye zvimwe zvinhu.
Danfoss inochengetedza kodzero yekushandura zvigadzirwa zvayo pasina chiziviso. Izvi zvinoshandawo kune zvigadzirwa zvakaodha asi zvisina kuendeswa kunze kwekunge shanduko yakadaro inogona kuitwa pasina shanduko muchimiro, kukwana kana kushanda kwechigadzirwa.
Zvese zviratidziro zviri muchinhu ichi zvinhu zveDanfoss A/S kana Danfoss boka makambani. Danfoss uye Danfoss logo zviratidzo zveDanfoss A/S. Kodzero dzese dzakachengetwa.

Zvinyorwa / Zvishandiso

Danfoss Gasi Detection Controller Unit uye Kuwedzera Module [pdf] Bhuku reMushandisi
BC272555441546en-000201, Gasi Detection Controller Unit uye Expansion Module, Controller Unit uye Expansion Module, Expansion Module

References

User Manual