I-Global Automation Partner yakho
LI-Q25L…E
Linear Position Sensors
nge-Analog Output
Imiyalelo yokusetyenziswa
1 Malunga nale miyalelo
Le miyalelo yokusetyenziswa ichaza ulwakhiwo, imisebenzi kunye nokusetyenziswa kwemveliso kwaye iya kukunceda ukuba usebenzise imveliso njengoko kucetyiwe. Funda le miyalelo ngononophelo phambi kokuba usebenzise imveliso. Oku kukuthintela umonakalo onokwenzeka ebantwini, kwipropati okanye kwisixhobo. Gcina imiyalelo yokusetyenziswa kwixesha elizayo ngexesha lobomi benkonzo yemveliso. Ukuba imveliso idluliselwe, dlulisela le miyalelo ngokunjalo.
1.1 Amaqela ekujoliswe kuwo
Le miyalelo ijolise kumntu oqeqeshiweyo kwaye kufuneka ifundwe ngononophelo nguye nabani na ofakayo, ogunyazisayo, osebenzayo, ogcinayo, odiliza okanye olahla isixhobo.
1.2 Ingcaciso yeesimboli ezisetyenzisiweyo
Le miqondiso ilandelayo isetyenziswa kule miyalelo:
INGOZI
INGOZI ibonisa imeko enobungozi enomngcipheko omkhulu wokufa okanye ukulimala kakhulu ukuba ayiphetshwa.
ISILUMKISO
ISILUMKISO sibonisa imeko enobungozi enomngcipheko ophakathi wokufa okanye ukwenzakala okumandundu ukuba akuphetshwa.
ISILUMKO
ILUMKO ibonisa imeko eyingozi yomngcipheko ophakathi onokuthi ubangele ukwenzakala okuncinci okanye okuphakathi ukuba akuphetshwa.
ISAZISO
ISAZISO sibonisa imeko enokukhokelela kumonakalo wepropathi ukuba ayiphetshwa.
PHAWULA
QAPHELA libonisa iingcebiso, iingcebiso kunye nolwazi oluluncedo malunga neentshukumo ezithile kunye neenyani. Amanqaku awenza lula umsebenzi wakho kwaye akuncede uphephe umsebenzi owongezelelekileyo.
BIZELA ESENZWENI
Olu phawu lubonisa izenzo ekufuneka zenziwe ngumsebenzisi.
IZIPHUMO ZOKUSEBENZA
Olu phawu lubonisa iziphumo ezifanelekileyo zezenzo.
1.3 Amanye amaxwebhu
Ngaphandle kolu xwebhu, le mathiriyeli ilandelayo inokufumaneka kwi-Intanethi apha www.turck.com:
Ishiti yedatha
1.4 Ingxelo malunga nale miyalelo
Senza zonke iinzame zokuqinisekisa ukuba le miyalelo inolwazi kwaye icace kangangoko. Ukuba unazo naziphi na iingcebiso zokuphucula uyilo okanye ukuba ulwazi oluthile lulahlekile kuxwebhu, nceda uthumele iingcebiso zakho ku techdoc@turck.com.
2 Amanqaku kwimveliso
2.1 Ukuchongwa kwemveliso
- Isivamvo soluvo sendawo esisebenzayo
- Indlela yezindlu
- Inguqulelo yombane
- Indawo yokuma
P0 Akukho ndawo yokubeka
P1 I-P1-LI-Q25L
P2 I-P2-LI-Q25L
P3 I-P3-LI-Q25L - Uluhlu lokulinganisa
100 100…1000 mm, kwi-100 mm amanyathelo
1250…2000 mm, kwi-250 mm amanyathelo - Umgaqo osebenzayo
LI I-linear inductive - Into yokukhwela
M0 Akukho nto yokunyuswa
M1 M1-Q25L
M2 M2-Q25L
M4 M4-Q25L - Indlela yezindlu
Q25L Uxande, profile 25 × 35 mm - Inani lee-LEDs
X3 I-3 × i-LED - Imo yokuphuma
LIU5 Imveliso ye-analog
4…20 mA/0…10 V - Uthotho
E Isizukulwana esandisiweyo
- Uqhagamshelo lombane
- Uqwalaselo
1 Ubumbeko olusemgangathweni - Inani labafowunelwa
5 5 pin, M12 × 1 - Isidibanisi
1 Ngqo - Isidibanisi
H1 Indoda M12 × 1
2.2 Umda wonikezelo
Umda wokuhanjiswa ubandakanya:
Uluvo lwendawo yomgca (ngaphandle kwesiqalelo sokubeka)
Ngokuzikhethela: Indawo yokuma kunye nesixhobo sokunyuswa
2.3 Inkonzo yeTurk
I-Turck iyakuxhasa ngeeprojekthi zakho, ukusuka kuhlalutyo lokuqala ukuya ekugunyazisweni kwesicelo sakho. I-database yemveliso ye-Turck phantsi www.turck.com iqulethe izixhobo zesoftware yokucwangcisa, uqwalaselo okanye ugunyaziso, amaphepha edatha kunye neCAD files kwiifomati ezininzi zokuthumela ngaphandle.
Iinkcukacha zoqhagamshelwano zeTurck subsidiaries kwihlabathi jikelele zinokufumaneka kwiphepha. [
26].
3 Ukuze ukhuseleke
Imveliso yenzelwe ngokweteknoloji yezobugcisa. Nangona kunjalo, iingozi ezishiyekileyo zisekho. Qwalasela ezi zilumkiso zilandelayo kunye nezaziso zokhuseleko ukuthintela umonakalo ebantwini kunye nempahla. U-Turck akamkeli tyala ngomonakalo owenziwe kukusilela ukuthobela ezi zilumkiso kunye nokhuseleko.
3.1 Ukusetyenziswa okucetywayo
I-inductive linear position sensors zisetyenziselwa umlinganiselo wokungaqhagamshelwa kwaye unganxibi-free indawo yokulinganisa indawo.
Izixhobo zingasetyenziswa kuphela njengoko kuchaziwe kule miyalelo. Naluphi na olunye usetyenziso aluhambelani nokusetyenziswa okujoliswe kuko. UTurck akamkeli butyala ngawo nawuphi na umonakalo owenziweyo.
3.2 Ukusetyenziswa gwenxa okucacileyo
Izixhobo azikho amacandelo okhuseleko kwaye akufanele zisetyenziselwe ukhuseleko lomntu okanye ipropathi.
3.3 Amanqaku okhuseleko ngokubanzi
Esi sixhobo sinokudityaniswa kuphela, sifakwe, sisetyenziswe, sibekwe ngokwepharamitha kwaye sigcinwe ngabasebenzi abaqeqeshwe ngobungcali.
Isixhobo sinokusetyenziswa kuphela ngokuhambelana nemigaqo, imigangatho kunye nemithetho esebenzayo kazwelonke neyamazwe ngamazwe.
Isixhobo sihlangabezana neemfuno ze-EMC kwiindawo zoshishino. Xa isetyenziswa kwiindawo zokuhlala, thatha amanyathelo okuthintela ukuphazamiseka koonomathotholo.
4 Inkcazo yemveliso
I-inductive linear position sensors ye-Li-Q25L imveliso yochungechunge iqulethe i-sensor kunye ne-positioning element. Amacandelo amabini enza isixokelelwano somlinganiselo wokulinganisa ukuguqula uguquko olulinganisiweyo, ubude okanye indawo.
Abenzi boluvo babonelelwa ngobude bokulinganisa be-100…2000 mm: Kuluhlu lwe-100…1000-mm, ukwahluka kufumaneka kwi-100-mm yokunyuswa, kuluhlu lwe-1000…2000-mm kwi-250-mm increments. Uluhlu oluphezulu lokulinganisa lwenzwa luchongwa ngobude bayo. Nangona kunjalo, indawo yokuqala yoluhlu lokulinganisa lunokutshintshwa ngabanye kusetyenziswa inkqubo yokufundisa.
Isivamvo sigcinwe kwi-aluminiyam yoxandefile. Indawo yokubeka ifumaneka ngeendlela ezahlukeneyo kwizindlu zeplastiki (cf. uluhlu lwezincedisi kwisahluko 4.5). Isivamvo kunye nendawo yokubeka izalisekisa iimfuno zodidi lokhuselo lwe-IP67 kwaye inokumelana nokungcangcazela kwamalungu omatshini ashukumayo kunye noluhlu lwezinye iimeko ezindlongo ezihlala ixesha elide. Isivamvo kunye nesici sokubeka kunye zenza ukuba ungaqhagamshelwa kunye nokulinganisa okunganxitywanga. Abenzi boluvo basebenza kwimowudi epheleleyo. Amandla wenatagI-es ayifuni uhlengahlengiso lwe-zero offset okanye uhlengahlengiso. Onke amaxabiso eendawo amiselwa njengamaxabiso apheleleyo. Iintshukumo zeHoming emva komthamotage drop akuyomfuneko.
4.1 Isixhobo sigqityiweview
Umzobo 1: Imilinganiselo kwi-mm – L = 29 mm + ubude bokulinganisa + 29 mm
Umzobo 2: Imilinganiselo – ubude besixhobo
4.2 Iipropati kunye neempawu
Ubude bomlinganiselo ukusuka kwi-100…2000 mm
Ubungqina bomothuko ukuya kuma-200 g
Ugcina umgca phantsi komthwalo womothuko
Amajoni omzimba kuphazamiseko lwe-electromagnetic
5-kHz sampulwimi
Isisombululo se-16-bit
4.3 Umgaqo wokusebenza
I-Li-Q25L i-sensor ye-linear positions sensors inomsebenzi ongaqhagamshelwanga ngokusekelwe kumgaqo wokulinganisa i-inductive resonant circuit. Ukulinganisa kukhuselekile kwimihlaba yemagnethi njengoko indawo yokumisa ingasekelwanga kwimagnethi kodwa kwinkqubo yekhoyili. Isivamvo kunye nesixhobo sokubeka senza inkqubo yokulinganisa ekhuthazayo. Umqulu owenziweyotage ivelisa izibonakaliso ezifanelekileyo kwiikhoyili zomamkeli we-sensor, kuxhomekeke kwindawo yendawo yokubeka. Iimpawu zivavanywa kwiprosesa yangaphakathi ye-16-bit ye-sensor kunye nemveliso njengeempawu ze-analog.
4.4 Imisebenzi kunye neendlela zokusebenza
Izixhobo zibonisa i-current kunye ne-voltagimveliso. Isixhobo sibonelela ngoku kunye ne-voltagUmqondiso we-e kwimveliso ngokomlinganiselo kwindawo yento yokubeka.
Umzobo 3: Iimpawu zemveliso
4.4.1 Umsebenzi wemveliso
Uluhlu lokulinganisa lwenzwa luqala kwi-4 mA okanye i-0 V kwaye luphele kwi-20 mA okanye i-10 V. Okwangoku kunye ne-voltagi-e output ingasetyenziswa ngaxeshanye. Okwangoku kunye ne-voltagIziphumo ze-e zinokusetyenziswa ngaxeshanye kwimisebenzi efana novavanyo lwesignali olungafunekiyo. Ukongeza, enye iyunithi yokubonisa inokufumana isignali ngelixa isibonakaliso sesibini siqhutyelwa yi-PLC.
Ukongeza kwii-LEDs, inzwa inika umsebenzi wolawulo olongezelelweyo. Ukuba i-positioning element ingaphandle koluhlu lokufumanisa kunye nokudibanisa phakathi kwe-sensor kunye ne-positioning element iphazamisekile, ukukhutshwa kwe-analog ye-sensor output 24 mA okanye i-11 V njengophawu lwephutha. Le mpazamo ke ngoko inokuvavanywa ngokuthe ngqo ngolawulo lomgangatho ophezulu.
4.5 Izincedisi zobugcisa
4.5.1 Izixhobo zokufaka
| Umzobo wobukhulu | Uhlobo | ID | Inkcazo |
|
I-P1-LI-Q25L | 6901041 | Indawo ekhokelwayo ye-LI- Q25L yezivamvo zomda ezifakwe kwi-groove ye-sensor |
|
I-P2-LI-Q25L | 6901042 | Isixhobo sokumisa esidadayo se-LI-Q25L sezivamvo zomngxunyana; umgama oqhelekileyo kwi-sensor yi-1.5 mm; ukudibanisa kunye ne-linear position sensor kwi-mgama ukuya kwi-5 mm okanye ukunyamezela kakubi ukuya kwi-4 mm. |
|
I-P3-LI-Q25L | 6901044 | Isixhobo sokumisa esidadayo se-LI-Q25L sezivamvo zomngxunyana; isebenza kwi-offset ye-90 °; umgama oqhelekileyo kwi-sensor yi-1.5 mm; ukudibanisa kunye ne-linear position sensor kwi-mgama ukuya kwi-5 mm okanye ukunyamezela kakubi ukuya kwi-4 mm. |
|
I-P6-LI-Q25L | 6901069 | Isixhobo sokumisa esidadayo se-LI-Q25L sezivamvo zomngxunyana; umgama oqhelekileyo kwi-sensor yi-1.5 mm; ukudibanisa kunye ne-linear position sensor kwi-mgama ukuya kwi-5 mm okanye ukunyamezela kakubi ukuya kwi-4 mm. |
|
I-P7-LI-Q25L | 6901087 | Indawo ekhokelwayo ye-LI- Q25L i-sensor yendawo ehambelanayo, ngaphandle kokudibana kwebhola |
 |
M1-Q25L | 6901045 | Ukunyuka kweenyawo ze-LI-Q25L iisensomvo zendawo ezihambelanayo; izinto eziphathekayo: aluminiyam; iipcs ezi-2. ngebhegi nganye |
 |
M2-Q25L | 6901046 | Ukunyuka kweenyawo ze-LI-Q25L iisensomvo zendawo ezihambelanayo; izinto eziphathekayo: aluminiyam; iipcs ezi-2. ngebhegi nganye |
 |
M4-Q25L | 6901048 | Isibiyeli sokunyuka kunye nebhloko yokutyibilika kwi-LI-Q25L i-sensors yendawo yomgca; izinto eziphathekayo: insimbi engenasici; iipcs ezi-2. ngebhegi nganye |
 |
MN-M4-Q25 | 6901025 | Ibhloko yesilayidi enentambo ye-M4 ye-backside profile ye-LI-Q25L yoluvo lwendawo yomgca; izinto eziphathekayo: isinyithi sesinyithi; 10 iipcs. ngebhegi nganye |
 |
AB-M5 | 6901057 | I-axial edibeneyo ye-guide positioning element |
 |
I-ABVA-M5 | 6901058 | I-axial edibeneyo yezinto ezikhokelwayo zokubeka; impahla: steel stainless |
 |
I-RBVA-M5 | 6901059 | I-angle edibeneyo ye-guide positioning element; impahla: steel stainless |
4.5.2 izincedisi Connection
| Umzobo wobukhulu | Uhlobo | ID | Inkcazo |
 |
TX1-Q20L60 | 6967114 | Fundisa iadaptha |
 |
I-RKS4.5T-2/TXL | 6626373 | Intambo yokudibanisa, i-M12 ikhonkco yowesifazane, iqonde, i-5-pin, ikhuselwe: 2 m, i-jacket material: PUR, emnyama; imvume ye-CUlus; obunye ubude bentambo kunye neenguqulelo ezikhoyo, bona www.turck.com |
5 Ukufaka
PHAWULA
Faka izinto zokubeka kwindawo embindini ngaphezulu koluvo. Jonga indlela yokuziphatha kwe-LED (jonga kwisahluko "Ukusebenza").
Faka isivamvo sendawo yomgca kwisistim usebenzisa izincedisi zokunyusela ezifunekayo.
Umfanekiso wesi-4: Eksample — ufakelo ngonyawo olukhwelayo okanye isibiyeli sokuxhoma
| Into yokukhwela | Kucetyiswa ukuqinisa itorque |
| M1-Q25L | 3 Nm |
| M2-Q25L | 3 Nm |
| MN-M4-Q25L | 2.2 Nm |
| Uhlobo lwenzwa | Inani elicetyiswayo lokulungiswa |
| LI100…LI500 | 2 |
| LI600…LI1000 | 4 |
| LI1250…LI1500 | 6 |
| LI1750…LI2000 | 8 |
5.1 Ukufakwa kwezinto zokubeka simahla
Embindini wesiqalelo sokumisa simahla ngaphezulu koluvo.
Ukuba i-LED 1 ilayita tyheli, indawo yokumisa ikuluhlu lokulinganisa. Ubulunga bomqondiso wehlisiwe. Lungisa ulungelelwaniso lwento yokumisa de i-LED 1 ikhanyise ngokuluhlaza.
Ukuba i-LED 1 idanyaza tyheli, indawo yokubeka ayikho kuluhlu lokulinganisa. Lungisa ulungelelwaniso lwento yokumisa de i-LED 1 ikhanyise ngokuluhlaza.
I-LED 1 ikhanyisa eluhlaza xa indawo yokumisa ikuluhlu lokulinganisa.
Umzobo 5: Embindini wesiqalelo sokumisa sasimahla
6 Uqhagamshelwano
ISAZISO
Isidibanisi esingafanelekanga sowesifazane
Umonakalo kwi-M12 ikhonkco eyindoda enokwenzeka
Qinisekisa uqhagamshelwano oluchanekileyo.
PHAWULA
I-Turck incoma ukusetyenziswa kweentambo zoqhagamshelwano ezikhuselekileyo.
Ngethuba lokufakela umbane wenzwa, gcina yonke inkqubo i-de-energized.
Qhagamshela umdibaniso wesetyhini wentambo yoqhagamshelo kwisidibanisi sendoda senzwa.
Qhagamshela isiphelo esivulekileyo sentambo yoqhagamshelo kunikezelo lwamandla kunye/okanye iiyunithi zokulungisa.
6.1 Umzobo wocingo
PHAWULA
Ukuthintela ukufundisa kungenjongo, gcina u-pin 5 ungekho okanye uvule isitshixo sokufundisa.
Umzobo 6: I-M12 isinxibelelanisi esiyindoda - i-pin assignment
Umzobo 7: I-M12 isixhumi sendoda - umzobo wocingo
7 Ukugunyaziswa
Emva kokudibanisa kunye nokutshintsha unikezelo lwamandla, isixhobo silungele ukusebenza ngokuzenzekelayo.
8 Ukusebenza
Iimpawu ze-8.1 ze-LED
Umzobo 8: ii-LEDs 1 kunye ne-2
| I-LED | Bonisa | Intsingiselo |
| I-LED 1 | Luhlaza | Indawo yokubeka phakathi koluhlu lokulinganisa |
| Lubhelu | Indawo yokuma phakathi koluhlu lokulinganisa ngomgangatho ocuthiweyo wophawu (umzekelo, umgama ukuya kwisivamvo mkhulu kakhulu) | |
| Ukubengezela okumthubi | Indawo yokuma ayikho kuluhlu lobhaqo | |
| Cimile | Indawo yokubeka ngaphandle koluhlu lokulinganisa oluseti | |
| I-LED 2 | Luhlaza | Unikezelo lwamandla alunampazamo |
9 Ukuseta
Umenzi woluvo unika olu khetho lulandelayo lwesicwangciso:
Cwangcisa isiqalo soluhlu lokulinganisa (inqaku elinguziro)
Cwangcisa isiphelo soluhlu lokulinganisa (indawo yokugqibela)
Lungisa kwakhona uluhlu lokulinganisa lube kwisetingi yasefektri: uluhlu olukhulu olunokubakho lokulinganisa
Cwangcisa kwakhona uluhlu lokulinganisa ukuya kulungiselelo lwasefektri olujikiweyo: uluhlu olukhulu olunokwenzeka lokulinganisa, ijika lemveliso lijikiwe
Vula/vula isitshixo sokufundisa
Uluhlu lokulinganisa lunokusetwa ngokubhula ngesandla okanye nge-adaptha yokufundisa ye-TX1-Q20L60. Inqaku elingu-zero kunye nesiphelo soluhlu lokulinganisa lunokusetwa ngokulandelelana okanye ngokwahlukileyo.
PHAWULA
Ukuthintela ukufundisa kungenjongo, gcina u-pin 5 ungekho okanye uvule isitshixo sokufundisa.
9.1 Ukuseta ngokusebenzisa ibhulorho ngesandla
9.1.1 Ukuseta uluhlu lokulinganisa
Nikeza isixhobo ngomthamotage.
Beka into yokumisa kwindawo enguziro oyifunayo kuluhlu lokulinganisa.
I-Bridge pin 5 kunye ne-pin 3 ye-2 s.
I-LED 2 idanyaza eluhlaza kwi-2 s ngexesha lokubhula.
Indawo ye-zero yoluhlu lokulinganisa igcinwe.
Nikeza isixhobo ngomthamotage.
Beka isiqalelo sokumisa kwindawo yokugqibela efunwayo yoluhlu lokulinganisa.
I-Bridge pin 5 kunye ne-pin 1 ye-2 s.
I-LED 2 idanyaza eluhlaza kwi-2 s ngexesha lokubhula.
Isiphelo soluhlu lokulinganisa lugcinwe
9.1.2 Seta kwakhona isivamvo kwisetingi zasefektri
Nikeza isixhobo ngomthamotage.
I-Bridge pin 5 kunye ne-pin 1 ye-10 s.
I-LED 2 iqale idanyaza eluhlaza kwi-2 s, emva koko ikhanyise ngokuluhlaza ngokuqhubekayo kwi-8s kwaye idanyaze eluhlaza kwakhona (emva kwe-10 iyonke).
Uluvo lusetwa kwakhona kwisetingi yefektri yayo.
9.1.3 Seta kwakhona isivamvo kwisethingi yasefektri eguqulweyo
Nikeza isixhobo ngomthamotage.
I-Bridge pin 5 kunye ne-pin 3 ye-10 s.
I-LED 2 iqale idanyaza eluhlaza kwi-2 s, emva koko ikhanyise ngokuluhlaza ngokuqhubekayo kwi-8s kwaye idanyaze eluhlaza kwakhona (emva kwe-10 iyonke).
Umenzi woluvo uphinda umiselwe kwisetingi yefektri eguqulweyo.
Ukumisela
Ukusetha ngeadaptha yokufundisa
9.1.4 Ukuvuselela isitshixo sokufundisa
PHAWULA
Umsebenzi wokutshixa ukufundisa uyenziwa ukuba usebenze xa uziswa.
Nikeza isixhobo ngomthamotage.
I-Bridge pin 5 kunye ne-pin 1 ye-30 s.
I-LED 2 iqale idanyaza eluhlaza kwi-2 s, emva koko ikhanyise eluhlaza ngokuqhubekayo kwi-8s, ikhanyise eluhlaza kwakhona (emva kwe-10 iyonke) kwaye idanyaza eluhlaza (emva kwe-30 iyonke) kwi-frequency ephezulu.
Umsebenzi wokutshixa wokufundisa wenzwa uyasebenza.
9.1.5 Ukuvala i-teacher lock
Nikeza isixhobo ngomthamotage.
I-Bridge pin 5 kunye ne-pin 1 ye-30 s.
I-LED 2 ikhanyisa ngokuluhlaza ngokuqhubekayo kwi-30s (i-lock lock isasebenza) kwaye emva kwe-30 s idanyaza eluhlaza kwi-frequency ephezulu.
Umsebenzi wokutshixa wokufundisa wenzwa uvaliwe.
9.2 Ukuseta ngeadaptha katitshala
9.2.1 Ukuseta uluhlu lokulinganisa
Nikeza isixhobo ngomthamotage.
Beka isiqalelo sokumisa kwindawo enguziro yoluhlu lokulinganisa.
Fundisa-kwiqhosha lokutyhala kwiadaptha ye-2 s ngokuchasene ne-GND.
I-LED 2 idanyaza eluhlaza kangangemizuzu emi-2 kwaye emva koko ilayita ngokuluhlaza okokoko.
Indawo ye-zero yoluhlu lokulinganisa igcinwe.
Nikeza isixhobo ngomthamotage.
Beka indawo yokubeka kwindawo ekupheleni koluhlu lokulinganisa.
Fundisa kwiqhosha lokutyhala kwiadaptha yemizuzu emi-2 ngokuchasene ne-UB.
I-LED 2 idanyaza eluhlaza kangangemizuzu emi-2 kwaye emva koko ilayita ngokuluhlaza okokoko.
Indawo ye-zero yoluhlu lokulinganisa igcinwe.
9.2.2 Seta kwakhona isivamvo kwisetingi zasefektri
Nikeza isixhobo ngomthamotage.
Fundisa kwiqhosha lokutyhala kwiadaptha yemizuzu emi-10 ngokuchasene ne-UB.
I-LED 2 iqale idanyaza eluhlaza kwi-2 s, emva koko ikhanyise ngokuluhlaza ngokuqhubekayo kwi-8s kwaye idanyaze eluhlaza kwakhona (emva kwe-10 iyonke).
Uluvo lusetwa kwakhona kulungiselelo lwasefektri.
9.2.3 Seta kwakhona isivamvo kwisethingi yasefektri eguqulweyo
Nikeza isixhobo ngomthamotage.
Fundisa-kwiqhosha lokutyhala kwiadaptha ye-10 s ngokuchasene ne-GND.
I-LED 2 iqale idanyaza eluhlaza kwi-2 s, emva koko ikhanyise ngokuluhlaza ngokuqhubekayo kwi-8s kwaye idanyaze eluhlaza kwakhona (emva kwe-10 iyonke).
Umenzi woluvo uphinda umiselwe kwisetingi yasefektri eguqulweyo.
9.2.4 Ukuvuselela isitshixo sokufundisa
PHAWULA
Umsebenzi wokutshixa ukufundisa uyenziwa ukuba usebenze xa uziswa.
Nikeza isixhobo ngomthamotage.
Fundisa kwiqhosha lokutyhala kwiadaptha yemizuzu emi-30 ngokuchasene ne-UB.
I-LED 2 iqale idanyaza eluhlaza kwi-2 s, emva koko ikhanyise eluhlaza ngokuqhubekayo kwi-8s, ikhanyise eluhlaza kwakhona (emva kwe-10 iyonke) kwaye idanyaza eluhlaza (emva kwe-30 iyonke) kwi-frequency ephezulu.
Umsebenzi wokutshixa wokufundisa wenzwa uyasebenza.
9.2.5 Ukuvala i-teacher lock
Nikeza isixhobo ngomthamotage.
Fundisa kwiqhosha lokutyhala kwiadaptha yemizuzu emi-30 ngokuchasene ne-UB.
I-LED 2 ikhanyisa ngokuluhlaza ngokuqhubekayo kwi-30s (i-lock lock isasebenza) kwaye emva kwe-30 s idanyaza eluhlaza kwi-frequency ephezulu.
Umsebenzi wokutshixa wokufundisa wenzwa uvaliwe.
10 Ukusombulula ingxaki
Amandla okudibanisa i-resonance kuboniswa yi-LED. Naziphi na iimpazamo zibonakaliswe ngee-LEDs.
Ukuba ifowuni ayisebenzi ngokulindelekileyo, qala ujonge ukuba kukho uphazamiseko lwe-ambient. Ukuba akukho siphazamiso se-ambient ekhoyo, jonga udibaniso lwesixhobo malunga neziphene.
Ukuba akukho ziphoso, kukho ukungasebenzi kakuhle kwesixhobo. Kule meko, ukuphelisa isixhobo kwaye ubeke endaweni yayo ngesixhobo esitsha sohlobo olufanayo.
11 Ugcino
Qinisekisa ukuba uqhagamshelo lweplagi kunye neentambo zihlala zikwimeko entle.
Izixhobo azigcinwanga, zicocekile zomile ukuba ziyafuneka.
12 Ukulungisa
Isixhobo kufuneka singalungiswa ngumsebenzisi. Isixhobo kufuneka sirhoxiswe ukuba sinengxaki. Jonga iimeko zethu zokubuyiswa kokwamkelwa xa sibuyisela isixhobo eTurck.
12.1 Ukubuyisela izixhobo
Ukubuyela e-Turck kunokwamkelwa kuphela ukuba isixhobo sixhotyiswe ngesibhengezo se-Decontamination esivalelweyo. Isibhengezo sokungacoceki sinokukhutshelwa kuso https://www.turck.de/en/retoure-service-6079.php kwaye kufuneka izaliswe ngokupheleleyo, kwaye incanyathiselwe ngokukhuselekileyo kunye nobungqina bemozulu ngaphandle kwepakethe.
13 Ukulahlwa
Izixhobo kufuneka zilahlwe ngokuchanekileyo kwaye akufanele zifakwe kwinkunkuma yasekhaya ngokubanzi.
14 Idatha yobugcisa
| Idatha yobugcisa | |
| Imilinganiselo yoluhlu lweenkcukacha | |
| Uluhlu lokulinganisa | 100...1000 mm kwi-100-mm ukunyuka; 1250…2000 mm kwi-250-mm ukunyuka |
| Isigqibo | 16 bit |
| Umgama oqhelekileyo | 1.5 mm |
| Indawo eyimfama a | 29 mm |
| Indawo eyimfama b | 29 mm |
| Ukuphindaphinda ukuchaneka | ≤ 0.02% yesikali esipheleleyo |
| Ukunyamezela umgca | Kuxhomekeke kubude bomlinganiselo (jonga i-data sheet) |
| Ukukhukuliseka kobushushu | ≤ ± 0.003 %/K |
| I-Hysteresis | Ishiyiwe ngokomgaqo |
| Ubushushu obugciniwe | -25…+70 °C |
| Ukusebenza ivoltage | 15… 30 VDC |
| Ripple | ≤10 % eUss |
| Uvavanyo lwe-insulation voltage | ≤ 0.5 kV |
| Ukukhuselwa kwexesha elifutshane | Ewe |
| Ukuqhawuka kocingo / ukubuyisela umva ukukhuseleka kwepolarity | Ewe/ewe (ubonelelo lwamandla) |
| Umsebenzi wemveliso | I-5-pin, imveliso ye-analog |
| Umqulutagimveliso | 0…10 V |
| Imveliso yangoku | 4…20 mA |
| Ukumelana nomthwalo, voltagimveliso | ≥ 4.7 kΩ |
| Ukumelana nomthwalo, imveliso yangoku | ≤ 0.4 kΩ |
| Sampulwimi | 5 kHz |
| Ukusetyenziswa kwangoku | < 50 mA |
| Yila | Uxande, Q25L |
| Imilinganiselo | (Ubude bokulinganisa + 58) × 35 × 25 mm |
| Izinto zendlu | I-aluminiyam yeAnodized |
| Izinto eziphathekayo zobuso obusebenzayo | Iplastiki, i-PA6-GF30 |
| Uqhagamshelo lombane | Isixhumi esiyindoda, i-M12 × 1 |
| Ukuxhathisa ukungcangcazela (EN 60068-2-6) | 20 g; 1.25 h/i-axis; 3 izembe |
| Ukuchasana nokothuka (EN 60068-2-27) | 200 g; 4 ms ½ sine |
| Uhlobo lokhuseleko | IP67/IP66 |
| MTTF | 138 iminyaka acc. ukuya kwi-SN 29500 (Ed. 99) 40 °C |
| Ubungakanani obupakishweyo | 1 |
| Ukusebenza ivoltaguphawu | I-LED: eluhlaza |
| Uluhlu lokulinganisa umboniso | I-Multifunction LED: eluhlaza, tyheli, ukukhanya okutyheli |
15 Iinkampani ezincedisayo zaseTurk — iinkcukacha zoqhagamshelwano
Jemani Hans Turck GmbH & Co. KG
Witzlebenstraße 7, 45472 Mülheim an der Ruhr
www.turck.de
Ostreliya Turck Australia Pty Ltd
Isakhiwo 4, 19-25 Duerdin Street, Notting Hill, 3168 Victoria
www.turck.com.au
Bheljiyam TURCK MULTIPROX
Ingonyama d'Orweg 12, B-9300 Aalst
www.multiprox.be
Brazil Turck do Brasil Automação Ltda.
Rua Anjo Custódio Nr. 42, Jardim Analia Franco, CEP 03358-040 São Paulo
www.turck.com.br
eTshayina I-Turck (Tianjin) iSensor Co.
18,4th Xinghuazhi Road, Xiqing uMmandla woPhuhliso loQoqosho, 300381
eTianjin
www.turck.com.cn
Fransi TURCK BANNER SAS
11 rue de Courtalin Bat C, Magny Le Hongre, F-77703 MARNE LA VALLEE
Cedex 4
www.turckbanner.fr
Igreat Britain TURCK BANNER LIMITED
Blenheim House, Hurricane Way, GB-SS11 8YT Wickford, Essex
www.turckbanner.co.uk
Indiya TURCK India Automation Pvt. Ltd.
401-403 Aurum Avenue, Survey. Hayi 109/4, Kufuphi neCummins Complex,
Baner-Balewadi Link Rd., 411045 Pune – Maharashtra
www.turck.co.in
ElamaTaliyane TURCK BANNER SRL
Via San Domenico 5, IT-20008 Bareggio (MI)
www.turckbanner.it
Japhan TURCK Japan Corporation
Syuuhou Bldg. 6F, 2-13-12, Kanda-Sudacho, Chiyoda-ku, 101-0041 Tokyo
www.turck.jp
Khanada Inkampani Turck Canada Inc.
140 Duffield Drive, CDN-Markham, Ontario L6G 1B5
www.turck.ca
eKorea I-Turck Korea Co, Ltd.
B-509 Gwangmyeong Technopark, 60 Haan-ro, Gwangmyeong-si,
14322 Gyeonggi-Do
www.turck.kr
Maleyishiya Ibhena yaseTurck yaseMalaysia Sdn Bhd
Iyunithi A-23A-08, Tower A, Pinnacle Petaling Jaya, Jalan Utara C,
46200 Petaling Jaya Selangor
www.turckbanner.my
Mekhsikho Turck Comercial, S. de RL de CV
Blvd. Campestre No. 100, Parque Industrial SERVER, CP 25350 Arteaga,
Coahuila
www.turck.com.mx
elamaDatshi Turk BV
I-Ruiterlaan 7, NL-8019 BN Zwolle
www.turck.nl
Ostriya I-Turck GmbH
Graumanngasse 7/A5-1, A-1150 Wien
www.turck.at
Pholend I-TURCK sp.zoo
Wroclawska 115, PL-45-836 Opole
www.turck.pl
Romaniya Turck Automation Romania SRL
Str. Siriului nr. 6-8, iCandelo 1, RO-014354 Bucuresti
www.turck.ro
IRussian Federation TURCK RUS OOO
2-nd Pryadilnaya Street, 1, 105037 Moscow
www.turck.ru
Swiden Turck Sweden Ofisi
Fabriksstråket 9, 433 76 Jonsered
www.turck.se
Singapho TURCK BANNER Singapore Pte. Ltd.
25 International Business Park, #04-75/77 (West Wing) Iziko laseJamani,
609916 eSingapore
www.turckbanner.sg
Mzantsi Afrika I-Turck Banner (Pty) Ltd
Boeing Road East, Bedfordview, ZA-2007 eRhawutini
www.turckbanner.co.za
Umphakathi waseCzech TURCK sro
Na Brne 2065, CZ-500 06 Hradec Králové
www.turck.cz
Thekhi Turck Otomasyon Ticaret Limited Sirketi
Inönü mah. Kayisdagi c., Yesil Konak Evleri No: 178, A Blok D:4,
34755 Kadiköy/ Istanbul
www.turck.com.tr
Hangari TURCK Hungary kft.
Árpád fejedelem útja 26-28., Óbuda Gate, 2. em., H-1023 Budapest
www.turck.hu
i-USA I-Turck Inc.
Ngowama-3000 Campus Qhuba, USA-MN 55441 Minneapolis
www.turck.us
Hans Turck GmbH & Co. KG | T +49 208 4952-0 | ngakumbi@turck.com | www.turck.com
V03.00 | 2022/08
Ngaphezulu kwama-30 amacandelo kunye
Imiboniso engama-60 kwihlabathi liphela!
100003779 | 2022/08
Amaxwebhu / Izibonelelo
 |
TURCK LI-Q25L…E Izivamvo zeNdawo zoMtya ezineZiphumo zeAnalog [pdf] Incwadi Yomyalelo I-LI-Q25L E i-Linear Position Sensors ene-Analog Output, LI-Q25L E, i-Linear Position Sensors ezine-Analog Output, ii-Linear Position Sensors, i-Analog Output Sensors, iiSensors |
