NEOMITIS PRG7 7 Hnub Ob Channel Digital Programmer

Cov ntaub ntawv khoom

PRG7 7 Hnub Ob Channel Digital Programmer

PRG7 yog tus programmer digital tsim los tswj cov tshuab cua sov. Nws nta ob txoj kev thiab tso cai rau kev ua haujlwm txog li 7 hnub ua ntej. Cov khoom los nrog cov phab ntsa mounting phaj rau kev yooj yim installation.

Technical Specifications

• Fais fab mov: 220V-240V ~ 50Hz
• Qhov siab tshaj plaws Load: 6A

Ntim Cov Ntsiab Lus

• 1 x PRG7 Programmer
• 1 x Standard phab ntsa phaj
• 2 x Ntsia Hlau Anchors
• 2 x Screws

Cov lus qhia siv khoom

Mounting ntawm Phab Ntsa Mounting Phaj:

1. Unscrew 2 screws nyob hauv qab tus programmer tso nws.
2. Tshem cov phab ntsa ntawm lub programmer.
3. Ruaj ntseg phab ntsa phaj rau phab ntsa siv cov ntsia hlau muab thiab ua kom nws nrog cov kab rov tav thiab ntsug.
4. Yog tias xav tau qhov chaw mounting, siv qhov chaw khob tawm ntawm ob lub phab ntsa phaj thiab qhov chaw sib txuas ntawm tus programmer.

Kev xaim:

Nco tseg: Txhua qhov kev teeb tsa hluav taws xob yuav tsum tau ua los ntawm tus kws tshaj lij hluav taws xob lossis tus neeg muaj peev xwm.
Xyuas kom meej tias lub mains muab rau lub system yog cais ua ntej tshem tawm los yog refitting cov khoom rau lub backplate.
Txhua txoj hlua hluav taws xob yuav tsum ua raws li IEE cov cai thiab yuav tsum tau kho cov xaim nkaus xwb.

Cov kev sib txuas hauv qab no tau teev tseg:

Terminal	Kev sib txuas
N	Nruab nrab IN
L	Nyob IN
1	HW/Z2: Cov zis kaw zoo li qub
2	CH/Z1: Cov zis kaw zoo li qub
3	HW/Z2: Qhib cov zis tawm
4	CH/Z1: Qhib cov zis tawm

Mounting ntawm Programmer:

1. Muab tus programmer rov qab rau ntawm phab ntsa mounting phaj.
2. Ruaj ntseg tus programmer los ntawm screwing ob lub locking screws nyob rau hauv lub programmer.

Installer Settings:

Txhawm rau nkag mus rau qhov kev teeb tsa siab tshaj plaws, txav ob hom sliders mus rau qhov chaw tawm.
Thov xa mus rau tus neeg siv phau ntawv ua tiav rau cov lus qhia ntxaws ntxiv thiab cov ntaub ntawv.

PACK muaj

INSTALLATION

MOUNTING ntawm phab ntsa mounting phaj

Cov programmer digital yog tsau rau ntawm phab ntsa nrog phab ntsa phaj uas tau muab nrog cov khoom.

1. Unscrew 2 screws nyob rau hauv lub programmer.
2. Tshem cov phab ntsa ntawm lub programmer.
3. Ruaj ntseg ntawm phab ntsa nrog ob lub hau ntswj uas siv lub qhov kab rov tav thiab ntsug.
4. Nyob rau hauv cov ntaub ntawv ntawm nto mounting, ib tug khob tawm cheeb tsam yog muab rau ntawm phab ntsa phaj thiab nyob rau hauv sib thooj cheeb tsam ntawm lub programmer.

THAWJ

• Tag nrho cov kev teeb tsa hluav taws xob yuav tsum tau ua los ntawm ib tus kws tshaj lij hluav taws xob tsim nyog lossis lwm tus neeg muaj peev xwm. Yog tias koj tsis paub meej yuav ua li cas rau nruab qhov programmer tham nrog ib tus kws tshaj lij hluav taws xob lossis cua sov En-gineer. Tsis txhob tshem tawm lossis kho cov khoom siv rov qab rau hauv lub nraub qaum yam tsis muaj cov khoom siv loj rau lub kaw lus raug cais tawm.
• Txhua txoj hlua yuav tsum ua raws li IEE cov cai. Cov khoom no tsuas yog siv rau cov hlua khi ruaj khov.

Cov kab hluav taws xob sab hauv

• N = Nruab nrab IN
• L = Nyob IN

1. HW/Z2: Ib txwm kaw cov zis
2. CH/Z1: Ib txwm kaw cov zis
3. HW/Z2: Ib txwm qhib tso zis
4. CH/Z1: Ib txwm qhib tso zis

Cov kab kos duab

chaw nres nkoj system

chaw nres nkoj system

MOUNTING LUB PROGRAMMER

1. Hloov cov programmer ntawm phab ntsa mounting phaj.
2. Ruaj ntseg tus programmer los ntawm screwing ob locking screws nyob rau hauv lub programmer.

INSTALLER SETTINGS

ADVANCED INSTALLER Setting

Nkag mus

• Txav mus rau 2 hom sliders mus rau qhov chaw tawm.
• Txav mus rau qhov programming slider rau txoj hauj lwm.
• Nias ib txhij thiab rau 5 vib nas this.
• 5 kev teeb tsa qib siab tuaj yeem hloov kho.
• Nias kom txog thaum qhov kev xaiv yog nyob rau hauv cov zaub ces siv los yog xaiv koj xaiv.

Teem tooj / piav qhia

1. Xaiv hom gravity/pumped
2. Teem sijhawm 12 lossis 24 teev
3. Ua kom nws pib lub caij ntuj sov/Lub caij ntuj no hloov dua
4. Teem tus naj npawb ntawm ON / OFF lub sijhawm
5. Xaiv koj qhov system ntawm Z1 / Z2 lossis CH / HW
6. Activation ntawm backlight

• Lub ntiajteb txawj nqus / Pumped hom (1)
• Pre-set system yog Pumped.
• Nias los yog hloov mus rau lub ntiajteb txawj nqus (2).

1. Pumped
2. Lub ntiajteb txawj nqus
3. Tom qab ntawd txuag los ntawm kev txav lub programming slider lossis txuag thiab mus rau qhov chaw tom ntej los ntawm nias .

Teem sijhawm 12/24 teev (2)

• Tus nqi pre-set yog 12 teev.

1. Nias los yog hloov mus rau "24 teev".
2. Tom qab ntawd txuag los ntawm kev txav lub programming slider lossis txuag thiab mus rau qhov chaw tom ntej los ntawm nias.

Nws pib lub caij ntuj sov/Lub caij ntuj no hloov dua (3)

Qhov pib lub caij ntuj sov/Lub caij ntuj no hloov dua qub yog ON.

1. Nias los yog hloov mus rau OFF
2. Tom qab ntawd txuag los ntawm kev txav lub programming slider lossis txuag thiab mus rau qhov chaw tom ntej los ntawm nias.

Teem tus naj npawb ntawm ON / OFF lub sijhawm (4)

Koj tuaj yeem kho tus naj npawb ntawm ON / OFF hloov lub sijhawm. Tus naj npawb pre-set yog 2.

1. Nias los yog hloov mus rau 3 lub sijhawm.
2. Tom qab ntawd txuag los ntawm kev txav lub programming slider lossis txuag thiab mus rau qhov chaw tom ntej los ntawm nias .

Installation kev ua haujlwm (5)

Cov programmer digital tuaj yeem tswj hwm Central Cua Kub thiab Dej Kub lossis 2 thaj chaw. Qhov kev xaiv ua ntej yog CH / HW.

1. Nias los yog hloov mus rau Z1/Z2.
2. Tom qab ntawd txuag los ntawm kev txav lub programming slider lossis txuag thiab mus rau qhov chaw tom ntej los ntawm nias .

Nco tseg hais txog qhov Advanced installer nqis: Yog hais tias qhov programming slider raug txav mus, nws yuav txuag cov kev hloov pauv thiab tawm hauv hom installer.

Backlight (6)

Lub backlight tuaj yeem hloov tau. Tus nqi pre-set yog ON.

1. Nias los yog hloov mus rau OFF.
2. Tom qab ntawd txuag los ntawm kev txav lub programming slider lossis txuag thiab mus rau qhov chaw tom ntej los ntawm nias .

TECHNICAL SPECIFICATIONS

• Lub hwj chim: 220V-240V / 50Hz.
• Tawm tswv yim ib relay: 3 (2) A, 240V / 50Hz.
• Nyob impulse voltagib: 4000v.
• Micro disconnection: Hom 1B.
• Pollution degree: 2.
• Tsis siv neeg ua haujlwm: 100,000 cycles.
• Chav II.

Ib puag ncig:

• Ua haujlwm kub: 0 ° C rau + 40 ° C.
• Cia kub: ntawm -20 ° C rau + 60 ° C.
• Humidity: 80% ntawm +25 ° C (tsis condensation)
• Kev tiv thaiv ntsuas: IP30.
• UKCA tshaj tawm txog kev ua raws: Peb, Neomitis Ltd, ntawm no tshaj tawm raws li peb lub luag haujlwm ib leeg tias cov khoom tau piav qhia hauv cov lus qhia no ua raws li kev cai lij choj 2016 No.1101 (Electrical Equipment Safety Regulations), , 2016 No.1091 (Electromagnetic Compatibility Regulations), 2012 (n°3032). ROHS) thiab cov qauv tsim raws li hauv qab no:
• 2016 No.1101 (Kev Nyab Xeeb): EN 60730-1: 2011, EN 60730-2-7: 2010/
• AC: 2011, EN 60730-2-9: 2010, EN 62311: 2008
• 2016 No.1091 (EMC): EN 60730-1: 2011 / EN 60730-2-7: 2010 / AC: 2011 / EN 60730-2-9: 2010
• 2012 N°3032 (ROHS): EN IEC 63000: 2018
• Neomitis Ltd liab: 16 Great Queen Street, Covent Garden, London, WC2B 5AH UNITED KINGDOM – contactuk@neomitis.com
• EU tshaj tawm ntawm kev ua raws: Peb, Imhotep Creation, ntawm no tshaj tawm raws li peb lub luag haujlwm ib leeg tias cov khoom tau piav qhia hauv cov lus qhia no ua raws li cov lus qhia ntawm Cov Lus Qhia thiab cov qauv kev sib haum xeeb hauv qab no:
• Tshooj 3.1a (Kev Nyab Xeeb): EN60730-1: 2011 / EN60730-2-7: 2010 / EN60730-2-9: 2010 / EN62311: 2008
• Tshooj 3.1b (EMC): EN60730-1: 2011 / EN60730-2-7: 2010 / EN60730-2-9: 2010
• RoHS 2011/65/UE, hloov kho los ntawm Cov Lus Qhia 2015/863/UE & 2017/2102/UE: EN IEC 63000: 2018
• Imhotep Creation: ZI Montplaisir – 258 Rue du champ de chav kawm – 38780 Pont-Evêque – Fabkis – contact@imhotepcreation.com
• Neomitis Ltd thiab Imhotep Creation belongs rau Axenco Group.
• Lub cim , affixed rau ntawm cov khoom qhia tias koj yuav tsum muab pov tseg thaum kawg ntawm nws lub neej muaj txiaj ntsig ntawm qhov tshwj xeeb rov ua dua tshiab, raws li European Cov Lus Qhia WEEE 2012/19 / EU. Yog tias koj hloov nws, koj tuaj yeem xa rov qab mus rau lub khw muag khoom uas koj yuav cov khoom hloov pauv. Yog li, nws tsis yog cov khoom pov tseg hauv tsev. Cov khoom siv rov ua dua tshiab ua rau peb tiv thaiv ib puag ncig thiab siv cov peev txheej ntuj tsawg dua.

TshajVIEW

• Ua tsaug rau kev yuav peb PRG7, 7 hnub digital programmer.
• Nws yog los ntawm kev mloog koj cov kev xav tau peb tau tsim thiab tsim peb cov khoom kom yooj yim rau kev khiav lag luam thiab nruab.
• Nws yog qhov yooj yim ntawm kev ua haujlwm uas yog npaj los ua kom koj lub neej yooj yim dua thiab pab koj txuag lub zog thiab nyiaj txiag.

CONTROLS THIAB DISPLAY

Programmer

Programming sliders sequences:
Lub sij hawm CH/Z1 programming HW/Z2 programming Khiav

LCD zaub

SETTINGS

POWER UP

1. Hloov ntawm lub programmer fais fab mov.
   • Tag nrho cov cim yuav tshwm rau ntawm lub vijtsam LCD raws li qhia rau ob vib nas this.
2. Tom qab 2 vib nas this, lub LCD yuav pom:
   • Lub sij hawm thiab hnub qub
   • Khiav icon ruaj khov
   • CH thiab HW systems yog OFF

Nco tseg: Lub ntsuas roj teeb qis yuav tshwm sim ntawm cov zaub thaum lub roj teeb yuav tsum tau hloov.
Nco ntsoov nqa cov roj teeb siv mus rau qhov chaw khaws cov roj teeb kom lawv tuaj yeem rov ua dua.

PROGRAMMING

Nco tseg: Chav tsev twb teem caij nrog rau hnub tim thiab sij hawm raug. Yog tias tus programmer xav rov pib dua vim li cas, thov saib cov lus qhia ntawm nplooj 3.

SET THE CH/Z1 THIAB HW/Z2 programming

1. Txav mus rau Programming slider mus rau txoj haujlwm. Txhua hnub ntawm lub lim tiam yog khov. Underscore thiab Yog / Tsis yog flashing.
2. Nias yog tias koj xav teem caij rau lwm hnub ntawm lub lim tiam. Underscore txav nyob rau hauv lwm hnub. Tom qab ntawd nias rau program rau hnub underscored.
3. Nias lossis kom nce / txo qis rau thawj lub sijhawm pib / tawm lub sijhawm pib. Ces nias kom paub meej.
4. Nias los yog kom nce / txo qis thawj zaug On/Off lub sij hawm kawg. Ces nias Yes kom paub meej.
5. Rov ua dua rau lub sijhawm thib ob On / Off thiab rau lub sijhawm thib peb On / Off. (Thov xa mus rau qhov kev teeb tsa siab tshaj plaws ntawm kev teeb tsa kev qhia kom ua rau lub sijhawm thib peb On / Off).

On/Off lub sij hawm	Lub sijhawm teem tseg
Ob lub sijhawm On/Off lub sijhawm
Lub Sijhawm 1	Pib thaum 06:30 teev sawv ntxov	Xaus ntawm 08:30 sawv ntxov
Lub Sijhawm 2	Pib thaum 05:00 teev tsaus ntuj	Xaus thaum 10:00 teev tsaus ntuj
Peb lub sijhawm On/Off lub sijhawm
Lub Sijhawm 1	Pib thaum 06:30 teev sawv ntxov	Xaus ntawm 08:30 sawv ntxov
Lub Sijhawm 2	Pib thaum 12:00 teev tsaus ntuj	Xaus thaum 02:00 teev tsaus ntuj
Lub Sijhawm 3	Pib thaum 05:00 teev tsaus ntuj	Xaus thaum 10:00 teev tsaus ntuj

• Txoj haujlwm tam sim no tuaj yeem luam tawm rau hnub tom ntej. Nias Yes rau luam los yog Tsis yog rau qhov kev pab cuam manually hnub tom qab.
• Xaub lub programming slider mus rau txoj haujlwm kom paub meej thiab ua haujlwm thib ob channel.
• Rov ua cov kauj ruam dhau los mus rau lub sijhawm On/Off rau HW/Z2.
• Thaum ua tiav, txav qhov program slider mus rau txoj haujlwm kom paub meej.

Kev ua haujlwm

MODE xaiv thiab piav qhia

• Hom sliders sequences rau CH/Z1 thiab HW/Z2: Tsis tu ncua txhua hnub nws pib tawm
• Tas mus li: Permanent ON hom. Lub kaw lus tau qhib mus tas li
• Txhua hnub: Lub kaw lus tig ON los ntawm thawj zaug
• Nyob rau lub sij hawm pib mus txog rau thaum kawg Off lub sij hawm kawg ntawm hnub tam sim no.
• Auto: Tsis siv neeg hom. Chav tsev tswj xyuas cov programming uas tau xaiv (saib "Kev Pabcuam" nplooj 2).
• Tawm: Permanent Off hom. Lub kaw lus nyob tsis tu ncua. Lub boost hom tseem siv tau.

BOOST

BOOST: Boost hom yog hom ib ntus uas tso cai rau koj hloov ON rau 1, 2 lossis 3 teev. Thaum kawg ntawm lub sijhawm teem, lub cuab yeej yuav rov qab mus rau nws qhov chaw ua ntej.

• BOOST yuav ua haujlwm los ntawm txhua hom kev khiav haujlwm.
• BOOST tau nkag los ntawm nias lub pob rau qhov sib txuas (CH / Z1 lossis HW / Z2).
• Nias 1 lub sij hawm teem 1 teev, 2 zaug teem 2 teev thiab 3 zaug teem 3 teev.
• BOOST raug tso tseg los ntawm nias dua ntawm Boost lossis txav ntawm sliders.
• Thaum BOOST tab tom khiav qhov kawg ntawm Boost lub sijhawm qhia rau txhua qhov system.

Nco tseg:

• Programming slider yuav tsum nyob rau hauv txoj hauj lwm.
• Yuav muaj kev ncua me ntsis ntawm kev nias thiab ua kom lub relay.

PIV TXWV

• Ua ntej: ua ntej hom yog hom ib ntus uas tso cai rau koj hloov ON lub kaw lus ua ntej, kom txog rau thaum lub sijhawm On / Off tom ntej.
• Nias khawm ntawm cov channel sib txuas kom qhib hom no.
• Nias dua khawm kom lov tes taw nws ua ntej kawg.

HOLIDAY

• Hnub so: Hnub so hom tso cai rau hloov lub cua sov (los yog Z1) thiab dej kub (los yog Z2) rau ib tug teev cov hnub, adjustable ntawm 1 thiab 99 hnub.

Txhawm rau teem caij so haujlwm:

1. Nias hnub khawm rau 5 vib nas this.
2. OFF tshwm rau ntawm qhov screen. Nias los yog kom nce lossis txo cov hnub.
3. Ces nias kom paub meej. cov cua kub (los yog Z1) thiab dej kub (los yog Z2) hloov Off thiab tus naj npawb ntawm remai-ning hnub yuav suav down rau zaub.
4. Txhawm rau tshem tawm cov haujlwm hnub so, nias lub pob.

REVIEW

Review: Review hom tso cai rau review txhua qhov programming hauv ib lub sijhawm. Cov review pib txij thaum pib ntawm lub lim tiam thiab txhua kauj ruam tshwm txhua 2 vib nas this.

Nias lub pob kom pib lub programming review.
Nias dua kom rov qab mus rau qhov kev ua haujlwm li qub.

Factory SETTINGS

Tej chaw Hoobkas chaw

• Ob lub sijhawm On/Off lub sijhawm
• Lub Sijhawm 1 Pib thaum 06:30 sawv ntxov Thaum 08:30 teev sawv ntxov
• Lub Sijhawm 2 Pib thaum 05:00 teev tsaus ntuj Thaum 10:00 teev tsaus ntuj
  • Peb lub sijhawm On/Off lub sijhawm
• Lub Sijhawm 1 Pib thaum 06:30 sawv ntxov Thaum 08:30 teev sawv ntxov
• Lub Sijhawm 2 Pib thaum 12:00 teev tsaus ntuj Thaum 02:00 teev tsaus ntuj
• Lub Sijhawm 3 Pib thaum 05:00 teev tsaus ntuj Thaum 10:00 teev tsaus ntuj

Nco tseg: Txhawm rau rov kho lub Hoobkas nqis, nias thiab tuav qhov no rau ntau tshaj 3 vib nas this siv lub ntsis ntiv tes.

Tag nrho cov duab LCD yuav qhib rau 2 vib nas this thiab lub Hoobkas teeb tsa yuav rov qab los.

SET HNUB THIAB TUB

1. Txav mus rau Programming slider mus rau txoj haujlwm. Lub xyoo preset yog ruaj.
2. Txhawm rau xaiv lub xyoo tam sim no, nias , kom nce xyoo. Nias, kom txo tau lub xyoo.
   • Nias kom paub meej thiab teeb tsa lub hli tam sim no.
3. Lub hli preset tshwm. Nias kom nce lub hli. Nias kom txo lub hli.
4. Lub preset hnub tshwm. Nias kom nce lub hnub. Nias kom txo qis hnub.

• Nias kom paub meej thiab teeb tsa hnub tam sim no.
• Nias kom paub meej thiab teeb tsa lub moos.
• 01 = Lub Ib Hlis; 02 = Feb; 03 = Peb. 04 = Peb. 05 = maj;
• 06 = June; 07 = Lub Xya Hli; 08 = aug; 09 = Sept; 10 = Kaum Ib Hlis;
• 11 = Nov; 12 = Kaum Ob Hlis
• Lub sij hawm preset tshwm. Nias kom nce lub sijhawm. Nias kom txo lub sijhawm
• Txav mus rau qhov program slider mus rau lwm txoj haujlwm kom paub meej / ua tiav qhov teeb tsa no.

KEV TIV THAIV

Zaub ploj ntawm programmer:

• Tshawb xyuas cov khoom siv fused spur.

Cua sov tsis tuaj rau:

• Yog tias CH Indicator teeb nyob rau ces nws tsis zoo li yuav ua txhaum nrog tus programmer.
• Yog tias CH qhov taw qhia lub teeb tsis ON ces kos qhov program ces sim BOOST vim qhov no yuav tsum ua haujlwm hauv txhua txoj haujlwm.
• Xyuas kom koj chav ntsuas cua sov hu kom sov.
• Xyuas seb lub boiler yog nyob rau.
• Xyuas tias koj lub twj tso kua mis ua haujlwm.
• Xyuas kom koj lub cev muaj zog valve yog tias haum tau qhib.

Cov dej kub tsis tuaj txog:

• Yog hais tias HW Indicator teeb nyob rau ces nws tsis zoo li yuav ua txhaum nrog tus programmer.
• Yog tias HW qhov taw qhia lub teeb tsis ON ces kos qhov program ces sim BOOST vim qhov no yuav tsum ua haujlwm hauv txhua txoj haujlwm.
• Xyuas seb koj lub Cylinder thermostat hu kom sov.
• Xyuas seb lub boiler yog nyob rau.
• Xyuas tias koj lub twj tso kua mis ua haujlwm.
• Xyuas kom koj lub cev muaj zog valve yog tias haum tau qhib.
• Yog tias muaj teeb meem tshwm sim, hu rau koj tus installer.

TECHNICAL SPECIFICATIONS

Thov xa mus rau cov lus qhia kev txhim kho rau cov ntaub ntawv hais txog cov qauv thiab cov khoom siv ib puag ncig.

Nco tseg

• Hauv qee lub sijhawm, chav tsev yuav raug teeb tsa nrog lub sijhawm ua haujlwm ua haujlwm tau qhib. Raws li txoj cai lij choj nyob rau hauv cov tsev xauj tsev, koj lub boiler roj yuav tsum raug tshuaj xyuas / kev pab cuam txhua xyoo kom ntseeg tau tias nws ua haujlwm raug.
• Qhov kev xaiv no yog tsim los ceeb toom cov neeg siv kawg kom tiv tauj tus neeg cuam tshuam kom muaj kev pabcuam txhua xyoo ua haujlwm ntawm lub boiler.
• Qhov kev ua haujlwm no yuav raug qhib thiab programmed los ntawm koj tus Installer, tu Engineer, lossis tus tswv tsev.
• Yog tias nws tau teeb tsa ua li ntawd, chav tsev yuav tso tawm cov lus ntawm lub vijtsam kom ceeb toom koj tias qhov kev pabcuam boiler yuav dhau sijhawm.
• Qhov Kev Pabcuam Sijhawm Sijhawm countdown yuav raug qhia txog 50 hnub ua ntej Kev Pabcuam yuav tsum tso sijhawm teem sijhawm rau tus kws ua haujlwm tuaj koom, kev ua haujlwm ib txwm yuav txuas ntxiv mus rau lub sijhawm no.tage.
• Thaum kawg ntawm qhov kev pabcuam no kom txog rau lub sijhawm sai sai, chav tsev yuav mus rau Kev Pabcuam Tshaj Tawm thaum lub sijhawm ntawd tsuas yog 1 teev kev txhawb nqa yuav ua haujlwm ntawm TMR7 thiab PRG7, yog tias chav tsev yog ntsuas kub RT1 / RT7, nws yuav ua haujlwm ntawm 20 ° C thaum lub sijhawm. lub sijhawm no.
• Yog tias PRG7 RF, Thermostat tsis muaj haujlwm.

PROGRAMMER yog dab tsi?

Kev piav qhia rau cov neeg nyob hauv tsev. Pro-grammers tso cai rau koj teem sijhawm 'On' thiab 'Off' lub sijhawm. Qee cov qauv hloov cov cua kub hauv nruab nrab thiab cov dej kub hauv tsev rau thiab tawm tib lub sijhawm, thaum lwm tus cia cov dej kub hauv tsev thiab cua sov tuaj thiab tawm ntawm lub sijhawm sib txawv. Teem lub sijhawm 'On' thiab 'Tawm' kom haum rau koj tus kheej txoj kev ua neej. Ntawm qee tus programmers koj yuav tsum tau teeb tsa seb koj puas xav kom cov cua sov thiab dej kub ua haujlwm tsis tu ncua, khiav hauv qab xaiv 'On' thiab 'Off' lub sijhawm cua sov, lossis mus tas li. Lub sijhawm ntawm tus programmer yuav tsum yog. Qee hom yuav tsum tau hloov kho thaum lub caij nplooj ntoos hlav thiab lub caij nplooj zeeg ntawm kev hloov ntawm Greenwich Mean Time thiab British Summer Time. Tej zaum koj yuav tuaj yeem kho qhov kev pab cuam cua sov ib ntus, piv txwv liample, 'Advance', or 'Boost'. Cov no tau piav qhia hauv cov chaw tsim khoom cov lus qhia. Cov cua sov yuav tsis ua haujlwm yog tias chav ntsuas cua sov tau hloov cua sov. Thiab, yog tias koj muaj lub tog raj kheej dej kub, cov cua kub dej yuav tsis ua haujlwm yog tias lub tog raj kheej ntsuas kub pom tias cov dej kub tau mus txog qhov kub thiab txias.

• www.neomitis.com
• NEOMITIS® LIMITED – 16 Great Queen Street, Covent Garden, London, WC2B 5AH UNITED KINGDOM Registered in England thiab Wales No: 9543404
• Tel: +44 (0) 2071 250 236 – Fax: +44 (0) 2071 250 267 – E-mail: contactuk@neomitis.com
• Cov cim lag luam sau npe - Txhua txoj cai tshwj tseg

Cov ntaub ntawv / Cov ntaub ntawv

NEOMITIS PRG7 7 Hnub Ob Channel Digital Programmer [ua pdf] Phau ntawv qhia PRG7 7 Hnub Ob Channel Digital Programmer, PRG7, 7 Hnub Ob Channel Digital Programmer, Ob Channel Digital Programmer, Digital Programmer, Programmer

Cov ntaub ntawv

• Cov neeg siv phau ntawv