Danfoss UL-HGX66e Reciprocating Compressor

Tlhahisoleseding ya Sehlahiswa

The Reciprocating Compressor ke mochini o hatelletsoeng o sebelisetsoang sehatsetsing. E tla ka mefuta e fapaneng e nang le litlhaloso tse fapaneng:

• UL-HGX66e/1340 ML 31
• UL-HGX66e/1540 ML 36
• UL-HGX66e/1750 ML 44
• UL-HGX66e/2070 ML 50
• UL-HGX66e/1340 S 37
• UL-HGX66e/1540 S 42
• UL-HGX66e/1750 S 50
• UL-HGX66e/2070 S 60

Litaelo tsa Tšebeliso ea Sehlahisoa

Polokeho
Ho bohlokoa ho ela hloko litaelo tsa polokeho ho thibela likotsi le likotsi tse mpe:

• Bala le ho latela litaelo tsohle tsa polokeho tse fanoeng bukeng ea litaelo.
• U se ke ua kopanya kapa ua sebelisa compressor ka mokhoa o fosahetseng.
• Ela hloko lileibole tsohle tsa polokeho ea lihlahisoa.
• Sheba mekhoa ea mohaho oa sebaka sa heno bakeng sa litlhoko tsa ho kenya.

Khokahano ea Motlakase
Buka ena e fana ka leseli mabapi le khokahano ea motlakase ea compressor:

• Litlhokomelo tse akaretsang tsa polokeho bakeng sa likhokahano tsa motlakase.
• Tlhahisoleseding bakeng sa khetho ea sehokahanyi le motlakase.
• Lits'oants'o tsa potoloho bakeng sa mefuta e fapaneng ea ho qala likoloi.
• Litaelo tsa khokahano bakeng sa yuniti ea trigger ea elektroniki INT69 G.
• Teko ea ts'ebetso ea yuniti ea trigger INT69 G.
• Lisebelisoa tsa boikhethelo joalo ka heater ea sump ea oli le taolo ea bokhoni.
• Khetho le ts'ebetso ea li-compressor tse nang le li-converter tsa maqhubu.

Lintlha tsa Tekheniki
Buka ena e fana ka lintlha tsa tekheniki tsa compressor:

• Tlhahisoleseding ka mekhahlelo ea motlakase le mechine.

Litekanyo le Maqhama
Bukana e fana ka lintlha le lintlha tsa khokahanyo bakeng sa compressor:

• Litekanyo tsa 'mele tsa compressor.
• Lintlha tsa khokahano le litlhoko.

Phatlalatso ea Kenyelletso
Buka ena e kenyelletsa phatlalatso ea ho kenngoa ha compressor:

• Phatlalatso ea semmuso e bolelang ho latela melao le maemo a amehang.

UL-Setifikeiti sa Tumellano
Bukana ena e kenyelletsa UL-Certificate of Compliance bakeng sa compressor:

• Setifikeiti sa semmuso se bonts'ang ho latela maemo a UL.

Ketapele

Kotsi

Kotsi ea likotsi.
Li-compressor tsa sehatsetsing ke mechini e hatelletsoeng ka matla, ka hona, li hloka tlhokomeliso e matla le tlhokomelo ha li sebetsoa.

Kopano le tšebeliso e fosahetseng ea compressor e ka fella ka kotsi e tebileng kapa e bolaeang!

• Ho qoba kotsi e mpe kapa lefu, ela hloko litaelo tsohle tsa polokeho tse fumanehang litaelong tsena pele u kopanya le pele u sebelisa compressor! Sena se tla qoba ho se utloisisane le ho thibela kotsi e tebileng kapa e bolaeang le tšenyo!
• Le ka mohla u se ke ua sebelisa sehlahisoa ka tsela e fosahetseng empa feela joalokaha u khothalelitsoe ke bukana ena!
• Ela hloko lileibole tsohle tsa polokeho ea lihlahisoa!
• Sheba mekhoa ea mohaho oa lehae bakeng sa litlhoko tsa ho kenya!

Liphetoho tse sa lumelloeng le litokiso ho sehlahisoa se sa kenyelletsoeng bukaneng ena li thibetsoe 'me li tla hlakola waranti!
Bukana ena ea litaelo ke karolo e tlamang ea sehlahisoa. E tlameha ho fumaneha ho basebetsi ba sebetsang le ba hlokomelang sehlahisoa sena. E tlameha ho fetisetsoa ho bareki ba ho qetela hammoho le yuniti eo compressor e kentsoeng ho eona. Tokomane ena e tlas'a tokelo ea molao ea BOCK GmbH, Jeremane. Lintlha tse fanoeng bukeng ena li ka fetoha le lintlafatso ntle le tsebiso.

Polokeho

Ho tsebahatsa litaelo tsa polokeho

• E supa boemo bo kotsi boo, ha bo sa qojoe, bo tla baka kotsi e bolaeang kapa e mpe hanghang.
• E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e mpe.
• E supa boemo bo kotsi boo, ha bo sa qojoe, bo ka bakang kotsi e mpe kapa e nyane.
• E supa boemo boo, ha bo sa qojoe, bo ka bakang tšenyo ea thepa.
• Lintlha tsa bohlokoa kapa malebela a ho nolofatsa mosebetsi.

Litaelo tse akaretsang tsa polokeho

Tlhokomediso

Kotsi ea likotsi.
Li-compressor tsa sehatsetsing ke mechini e hatelletsoeng ka matla, ka hona, li hloka tlhokomeliso e matla le tlhokomelo ha li sebetsoa.

Khatello e phahameng ka ho fetesisa e lumelletsoeng ha ea lokela ho fetisoa, esita le molemong oa liteko!

Kotsi ea ho cha!

• Ho ipapisitsoe le maemo a ts'ebetso, mocheso o kaholimo ho 140 ° F (60 ° C) ka lehlakoreng la ho tsoa kapa ka tlase ho 32 ° F (0 ° C) ka lehlakoreng la ho monya o ka finyelloa.
• Ho kopana le sehatsetsing ho tlameha ho qojoa. Ho kopana le sehatsetsing ho ka baka ho chesa ho matla le ho senyeha ha letlalo.

Tšebeliso e reriloeng

Tlhokomediso
Compressor e kanna ea se sebelisoe libakeng tse ka bang le ho phatloha!

• Litaelo tsena tsa kopano li hlalosa mofuta o tloaelehileng oa compressor e boletsoeng sehloohong se entsoeng ke Bock. Li-compressor tsa sehatsetsing sa Bock li reretsoe ho kenngoa mochining oa ma-machine (ka har'a EU ho latela EU Directives 2006/42/EC Machinery Directive, 2014/68/EU Pressure Equipment Directive, kantle ho EU ho latela melao le litataiso tsa naha tse fapaneng) .

Ho romelloa ho lumelloa feela haeba compressor e kentsoe ho latela litaelo tsena tsa kopano le tsamaiso eohle eo e kopantsoeng ho eona e hlahlobiloe le ho amoheloa ho latela melao ea molao.
Li-compressor li etselitsoe ho sebelisoa lits'ebetsong tsa sehatsetsi ho latela meeli ea ts'ebeliso. Ke feela sehatsetsi se boletsoeng litaelong tsena se ka sebelisoang.

Tšebeliso efe kapa efe e 'ngoe ea compressor e thibetsoe!

Litšoaneleho tse hlokahalang ho basebetsi
Basebeletsi ba sa rutehang ka mokhoa o lekaneng ba baka kotsi ea likotsi, phello e ba kotsi e mpe kapa e bolaeang. Ka hona, mosebetsi oa li-compressor o boloketsoe basebetsi ba tšoanelehang ho sebetsa lits'ebetsong tsa sehatsetsi tse hatelletsoeng:

• Bakeng sa mohlalaample, setsebi sa lihatsetsi, kapa moenjiniere oa mochini oa lihatsetsi. Hape le liporofeshene tse nang le lithupelo tse bapisoang tse nolofalletsang basebetsi ho bokella, ho kenya, ho hlokomela le ho lokisa litsi tsa sehatsetsi le li-air-conditioning. Basebeletsi ba tlameha ho khona ho lekola mosebetsi o lokelang ho etsoa le ho lemoha likotsi tse ka bang teng.

Tlhaloso ea Sehlahisoa

Tlhaloso e khutšoanyane

• Semi-hermetic six-cylinder reciprocating compressor e nang le enjene ea koloi e pholileng ea khase.
• Mokelikeli oa sehatsetsi o montsoeng ho tsoa mouoane o phalla holim'a enjene ebe oa o pholisa ka matla. Ka tsela ena, enjene e ka bolokoa maemong a mocheso a batlang a le tlase, haholo-holo tlas'a meroalo e phahameng.

Litekanyo le boleng ba khokahano li ka fumanoa khaolong ea 10.

Letlapa la mabitso (mohlalaample)

Tlanya senotlolo (mohlalaample)

1. HG - Hermetic Gas-Cooled (e monyang khase-e pholileng)
2. X - Tefiso ea oli ea Ester
3. S - Enjene e matla haholoanyane
   • ML - Enjene bakeng sa pholile e tloaelehileng le serame se tebileng

Libaka tsa kopo

Lihatsetsi

HFC + e kopanya	R134a, R404A/R507
Metsoako ea HFC/HFO	R448A, R449A, R450A, R513A

Lintlha tse ling mabapi le lihatsetsi tse amohetsoeng ho sesebelisoa sa khetho sa Bock compressor VAP (vap.bock.de).

Tefiso ea oli

• Li-compressor li tlatsitsoe fekthering ka mofuta o latelang oa oli: BOCK lub E55

Bakeng sa ho tlatsa, re khothaletsa mefuta e ka holimo ea oli. Sheba hape karolo ea 7.4.

TSEBISO
Boemo ba oli bo tlameha ho ba karolong e bonahalang ea khalase ea pono; Tšenyo ea compressor e ka etsahala haeba e tletse kapa e tlatsitsoe ka tlase!

Meeli ea kopo

TSEBISO
Ts'ebetso ea compressor e ka khoneha ka har'a meeli ea ts'ebetso. Tsena li ka fumaneha ho sesebelisoa sa khetho sa Bock compressor (VAP) tlasa vap.bock.de. Ela hloko lintlha tse fanoeng moo.

• Mocheso o lumelletsoeng oa tikoloho: -20°C…+60°C (-4°F…140°F)
• Max. mocheso o lumellehang oa ho qetela oa 140°C (284°F).
• Max. lumello ea ho fetola maqhubu a 12x / h.
• Nako e fokolang ea ho sebetsa ke 3 min. boemo bo tsitsitseng (ts'ebetso e tsoelang pele) e tlameha ho finyelloa.

Bakeng sa ts'ebetso e nang le pholiso ea tlatsetso:

• Sebelisa oli feela e nang le botsitso bo phahameng ba mocheso.
• Qoba ts'ebetso e tsoelang pele haufi le monyako.
• Mocheso oa mocheso o matla oa khase o ka hloka ho fokotsoa kapa o behoe ka bonngoe ha o sebetsa haufi le monyako.

Bakeng sa ts'ebetso e nang le taolo ea bokhoni:

• Ts'ebetso e tsoelang pele, ha taolo ea matla e sebetsa, ha e lumelloe mme e ka baka tšenyo ho compressor.
• Mocheso oa mocheso o matla oa khase o ka hloka ho fokotsoa kapa o behoe ka bonngoe ha o sebetsa haufi le monyako.
• Ha matla a taolo a sebetsa, lebelo la khase tsamaisong ha le khone ho netefatsa hore oli e lekaneng e khutlisetsoa ho compressor tlas'a maemo a itseng.

Bakeng sa ts'ebetso e nang le frequency converter:

• Tšebeliso e phahameng ea hona joale le ea matla ha ea lokela ho fetisoa. Tabeng ea ts'ebetso ka holim'a maqhubu a motlakase, moeli oa kopo o ka fokotsoa (max.(max. 60 Hz) 60 Hz).

Ha o sebetsa sebakeng sa vacuum, ho na le kotsi ea hore moea o kene ka lehlakoreng la ho hula. Sena se ka baka liphetoho tsa lik'hemik'hale, ho phahama ha khatello ka har'a condenser le mocheso o phahameng oa khase. Thibela ho kena ha moea ka litšenyehelo tsohle!

• Maqhubu a phahameng a amohelehang: 60 Hz
• Khatello e phahameng e lumellehang ea ts'ebetso (LP/HP)1): 19/28 barg (276/406 psig)
  • LP = Khatello e tlaase
  • HP = Khatello e phahameng

Kopano ea Compressor

Li-compressor tse ncha li tlatsitsoe ke fektheri ka khase ea inert. Tlohela tefiso ena ea ts'ebeletso ka har'a compressor ka nako e telele kamoo ho ka khonehang 'me u se ke ua thibela moea o kenang. Sheba sekontiri bakeng sa tšenyo ea lipalangoang pele u qala mosebetsi ofe kapa ofe.

Polokelo le lipalangoang

• Sebaka sa polokelo ho -30°C…+70°C (-22°F…+158°F), boholo bo lumelletsoeng mongobo o lekanyelitsoeng 10% – 95%, ha ho condensation
• Se boloke sebakeng se senyang, se lerole, se nang le mouoane kapa tikolohong e chang.
• Sebelisa leihlo la lipalangoang.
• U se ke ua phahamisa ka letsoho!
• Sebelisa lisebelisoa tsa ho phahamisa!

Ho beha
Li-attachments (mohlala, li-pipe, li-unit tse eketsehileng, likarolo tse tiisang, joalo-joalo) ka ho toba ho compressor ha lia lumelloa!

• Fana ka tumello e lekaneng bakeng sa mosebetsi oa tlhokomelo.
• Etsa bonnete ba hore ho na le moea o lekaneng oa compressor.
• Se sebelise sebakeng se senyang, se lerole, damp sepakapaka kapa tikoloho e chang.
• Seta holim'a sebaka se lekaneng kapa foreimi e nang le bokhoni bo lekaneng ba ho jara.
• Compressor e le 'ngoe ka ho khetheha ho vibrate damper.
• Li-circuits tsa Duplex le tse tšoanang li lula li le thata.
• Ho khothaletsoa ho kenya li-mufflers tsa vibration tsa pipe!

Lihokelo tsa liphaephe

Tšenyo e ka bang teng.
U se ke ua solder ha feela compressor e ntse e le tlas'a khatello. Ho chesa haholo ho ka senya valve. Ka hona, tlosa litšehetso tsa liphaephe ho tloha ho valve bakeng sa solder, 'me ka hona u pholile 'mele oa valve nakong le ka mor'a ho soasoa. Ke solder feela e sebelisang khase ea inert ho thibela lihlahisoa tsa oxidation (sekala).

• Lihokelo tsa lipeipi holim'a compressor li fumaneha bakeng sa ho soasoa kapa ho cheselletsa (lisebelisoa). Li-valve tsa ho ntša metsi le tsa ho monya li se li qetile ka hare ho bophara e le hore liphaephe tse nang le limilimithara tse tloaelehileng le boholo ba lisenthimithara li ka sebelisoa. Pipe e tla qoelisoa ka botebo ho ea ka boholo.
• Li-diameter tsa khokahanyo tsa li-valve tse koalang li lekantsoe bakeng sa tlhahiso e phahameng ea compressor. Karolo ea 'nete e hlokahalang ea phaephe ea sefapano e tlameha ho bapisoa le tlhahiso. Ho joalo le ka li-valve tse sa khutleng.

Liphaephe

• Liphaephe le likarolo tsa tsamaiso li tlameha ho hloeka le ho omella ka hare le ho se be le sekala, sekoti le lihlopha tsa mafome le phosphate. Sebelisa likarolo tse thibelang moea feela.
• Beha lipeipi ka nepo. Li- compensation tse loketseng tsa vibrate li tlameha ho fanoa ho thibela liphaephe hore li phatlohe le ho robeha ke ho thothomela ho matla.
• Etsa bonnete ba ho khutlisa oli e nepahetseng.
• Boloka tahlehelo ea khatello ho bonyane bo felletseng.

E qala ho laolla (ka ntle)
Feme ea khale ea ho laolla e qalang ha e fumanehe. Ntle le moo, ho ka kengoa setsi sa ho theolela thepa sa ho qala setsing.

Ts'ebetso:
Ha konpresser e qala, valve ea solenoid e fumana matla ka sesebelisoa sa nako ebe e bula tsela e fetang pakeng tsa mela e ntšang metsi le e monyang. Ka nako e ts'oanang, valve e sa khutleng molaong oa ho tsoa e koala 'me e thibela ho khutla ha sehatsetsing ho tloha ho condenser (setšoantšo sa 5). Compressor e se e potolohile ka nako e khuts'oane 'me e lopolla ho tsoa ho tsoa ka kotloloho ho kena. Ka lebaka leo, phapang ea khatello e fokotseha haholo. Ka lebaka leo, torque ho shaft drive ea compressor e fokotsehile haholo. Enjene ea ho khanna joale e ka qala ka boemo bo tlase ba torque ea ho qala. Hang ha motlakase le compressor li fihla lebelo la tsona le lekantsoeng, valve ea solenoid e koala 'me valve e sa khutleng e bula (setšoantšo sa 6). Hona joale compressor e sebetsa tlas'a mojaro o tloaelehileng.

Bohlokoa:

• Ho qala ho laolla ho ka sebelisoa feela nakong ea ho qala.
• Hlahloba valve ea solenoid le valve e sa khutleng khafetsa bakeng sa ho tiea.
• Ho phaella moo, re khothalletsa ho sebelisa thermostat ea tšireletso ea mocheso ka lehlakoreng la ho tsoa ha com-pressor. Sena se sireletsa konpresser khahlanong le ho tlala ha mocheso. Hokela thermostat ea tšireletso ea mocheso ka letoto la ketane ea polokeho ea potoloho ea taolo, ho tima konpresser ha ho hlokahala.
• Latela litaelo tsena ho qoba ho tlala ha mocheso.

Ho beha methapo ea ho hula le ea khatello

• Liphaephe tse kentsoeng ka tsela e fosahetseng li ka baka mapetsong le ho lla, phello e ba ho lahleheloa ke sehatsetsing.
• Peakanyo e nepahetseng ya mela e hulang le ya ho ntsha ka ho toba ka mora hore compressor e be karolo ya tshebetso e thellang le boitshwaro ba ho thothomela.

Molao oa letsoho: Kamehla beha karolo ea pele ea lipeipi ho tloha ho belofo e koalang ho ea tlase le e bapileng le shaft ea koloi.

Ho sebetsa li-valve tsa ho koala

• Pele o bula kapa o koala belofo e koalang, lokolla valve spindle ka hoo e ka bang. 1/4 ea ho chenchana ka tatellano ea oache.
• Ka mor'a ho kenya valve e koalang, tiisa seal spindle spindle ho ea ka nako.

Mokhoa oa ho sebetsa oa likhokahano tsa litšebeletso tse notlehang

Ho bula valve ea ho koala:

Spindle:
retelehela ka ho le letshehadi (counter-clockwise) moo e tla ya teng. —> Valofo e koetsoeng e butsoe ka botlalo / khokahano ea tšebeletso e koetsoe.

Ho bula khokahano ea litšebeletso

Spindle: Fetola 1/2 - 1 ho tjeka ho ea ka nako.

• Khokahano ea lits'ebeletso e butsoe / valve e koalang e butsoe.

Ka mor'a ho kenya letsoho, ka kakaretso kenya sekoahelo sa tšireletso sa spindle hape 'me u tiise ka 14-16 Nm (10-12 lb-ft). Sena se sebetsa e le tšobotsi ea bobeli ea ho tiisa nakong ea ts'ebetso.

Sefefo sa peipi ea ho hula le se omisang sefe
Bakeng sa litsamaiso tse nang le liphaephe tse telele le tekanyo e phahameng ea tšilafalo, ho kgothaletswa sefe se lehlakoreng la ho hula. Sefefa se tlameha ho nchafatsoa ho latela boemo ba tšilafalo (tahlehelo e fokotsehileng ea khatello). Mongobo oa potoloho ea sehatsetsing o ka lebisa ho sebopeho sa kristale le hydrate. Ka lebaka lena, re khothaletsa ho sebelisa mochini o omisang filthara le khalase ea pono e nang le sesupo sa mongobo.

Khokelo ea motlakase

Tšireletseho e akaretsang

• Kotsi ea ho tsosoa ke motlakase! Phallo e phahamengtage!
• Etsa mosebetsi feela ha sistimi ea motlakase e khaotsoe phepelong ea motlakase!
• Ha o hokela lisebelisoa ka thapo ea motlakase, ho tlameha ho bolokoe radius e kobehang bonyane 3 x bophara ba cable bakeng sa ho beha mohala.

Hokela enjene ea compressor ho latela setšoantšo sa potoloho (sheba kahare ho lebokose la terminal).

• Sebelisa thapo e loketseng ea ho kena ea mofuta o nepahetseng oa tšireletso (sheba poleiti ea lebitso) bakeng sa ho tsamaisa likhoele ka har'a lebokose la terminal. Kenya mats'oafo a ho imolla le ho thibela mats'oao a likhoele.
• Bapisa voltage le makhetlo a mangata le data bakeng sa phepelo ea motlakase ea mantlha.
• Hokela enjene feela haeba litekanyetso tsena li tšoana.

Tlhahisoleseding bakeng sa khetho ea sehokahanyi le motlakase
Lisebelisoa tsohle tsa ts'ireletso le li-switching kapa tsa ho beha leihlo li tlameha ho kengoa ho latela melaoana ea ts'ireletso ea lehae le lintlha tse behiloeng (mohlala, OSHA, UL/CSA) hammoho le tlhaiso-leseling ea moetsi. Li-switches tsa ts'ireletso ea likoloi lia hlokahala! Likhokahano tsa enjene, likhoele tsa phepelo, li-fuse le li-switches tsa ts'ireletso ea makoloi li tlameha ho lekanyetsoa ho latela boholo ba hajoale bo sebetsang (sheba poleiti ea mabitso). Bakeng sa ts'ireletso ea enjene, sebelisa sesebelisoa sa ts'ireletso se itšetlehileng ka bongata le se liehang ho feta nako bakeng sa ho beha leihlo mekhahlelong eohle e meraro. Beha sesebelisoa sa ts'ireletso ea boima bo feteletseng hore se tlameha ho sebelisoa nakong ea lihora tse 2, haeba ho na le makhetlo a 1.2 ho feta. sebetsa jwale.

Enjene e tloaelehileng, moralo bakeng sa qalo e otlolohileng kapa e sa fellang

Li-compressor tse nang le letšoao lena li loketse ho qala ka mokhoa o tobileng kapa o sa fellang. Motlakase oa motlakase o arotsoe ka likarolo tse peli:

• Karolo ea matsoelintsoeke 1 = 50% le karolo ea matsoelintsoeke 2 = 50%.
• Karohano ena ea matsoelintsoeke e fokotsa lebelo la ho qala le hlokahalang bakeng sa ho qala karolo e matsoelintsoeke ho ba hoo e ka bang. 50% ea seo bakeng sa qalo e tobileng.

Ho qala ka mochini o sa laoloeng ka "bypass solenoid valve" ha ho hlokahale.

Enjene e hoketsoe ka terata bakeng sa ho qala ka kotloloho (YY) fekthering. Bakeng sa karolo e qalang ea ho qala Y/YY marokho a tlameha ho tlosoa 'me mohala oa phepelo ea enjene o hoketsoe ho latela setšoantšo sa potoloho:

TSEBISO
Ho hlōleha ho etsa sena ho fella ka masimo a rotary a hanyetsanang le ho baka tšenyo ea motlakase. Kamora hore enjene e qale ka mokhoa o sa fellang oa 1, moea o sa fellang oa 2 o tlameha ho buloa ka mor'a tieho e kholo ea motsotsoana o le mong. Ho hloleha ho ikamahanya le maemo ho ka ama bophelo ba tšebeletso ea koloi hampe.

Setšoantšo sa motheo sa potoloho bakeng sa karolo ea matsoelintsoeke se qala ka enjene e tloaelehileng

BP2	Tlhokomelo e phahameng ea tšireletso ea khatello
BP3	Ketane ea polokeho (ho beha leihlo khatello e phahameng / e tlase)
BT1	Cold conductor (PTC sensor) motor winding
BT2	Thermostat e sireletsang mocheso (sensor ea PTC)
BT3	Sensor mocheso oa oli
BT4	Sesebelisoa sa ho lokolla (thermostat)
DELTA-P II	Sensor e fapaneng ea khatello ea oli DELTA-P II (sesebelisoa)
EB1	Mofuthu oa ho futhumatsa oli
EC1	Compressor motor

FC1.1/1.2	Phetoho ea tšireletso ea motlakase
FC2	Laola fuse ea potoloho ea matla
INT69 G	Yuniti ea ho bulela elektroniki INT69 G
KF1	Ho lieha ho khutlisetsoa morao bakeng sa switchover ea contactor
QA1	Phetoho e kholo
QA2	Mains contactor (karolo matsoelintsoeke 1)
QA3	Mains contactor (karolo matsoelintsoeke 2)
SF1	Taolo voltage switjha

Enjene e khethehileng: moralo oa ho qala ka kotloloho kapa ho qala ka naleli

Ho hlokahala qalo e sa laoloang ka mochini e nang le "bypass solenoid valve" bakeng sa qalo ea naleli.

Ho qala delta ea linaleli ho ka khoneha feela bakeng sa phepelo ea motlakase ea ∆ (230 V).

ExampLe:

• Fekthering enjene e kentsoe mohala bakeng sa ho otloloha ho qala ka matla a phahamengtage.
• Banyaluoa ba tla tlosoa bakeng sa star delta ho qala ka low voltage.

Setšoantšo sa motheo sa potoloho bakeng sa naleli-delta qala 230 V ∆ / 400 VY

BP2	Tlhokomelo e phahameng ea tšireletso ea khatello
BP3	Ketane ea polokeho (ho beha leihlo khatello e phahameng / e tlase)
BT1	Cold conductor (PTC sensor) motor winding
BT2	Thermostat e sireletsang mocheso (sensor ea PTC)
BT3	Sensor mocheso oa oli
BT4	Sesebelisoa sa ho lokolla (thermostat)
DELTA PII	Sensor e fapaneng ea khatello ea oli DELTA-P II (sesebelisoa)
EB1	Mofuthu oa ho futhumatsa oli
EC1	Compressor motor

FC1.1/1.2	Phetoho ea tšireletso ea motlakase
FC2	Laola fuse ea potoloho ea matla
INT69 G	Yuniti ea ho bulela elektroniki INT69 G
KF1	Ho lieha ho khutlisetsoa morao bakeng sa switchover ea contactor
QA1	Phetoho e kholo
QA2	Sehokelo sa mantlha
QA3	Δ-khokahanyo
QA4	Y-contactor
SF1	Taolo voltage switjha

Yuniti ea ho bulela elektroniki INT69 G
Enjene ea compressor e kentsoe li-sensor tse batang tsa mocheso oa conductor (PTC) tse hokahaneng le yuniti ea trigger ea elektroniki INT69 G ka lebokoseng la terminal. Boemong ba mocheso o feteletseng ha o potoloha enjene, INT69 G e koala sehokelo sa enjene. Ha e se e pholile, e ka qalisoa hape ha senotlolo sa elektroniki sa phepelo ea phepelo (li-terminals B1 + B2) se ka lokolloa ka ho sitisa phano ea phepelo.tage. Lehlakore le chesang la khase ea compressor le ka boela la sireletsoa khahlanong le mocheso o feteletseng ka ho sebelisa li-thermostats tsa tšireletso ea mocheso (sesebelisoa).

Yuniti e tsamaea ha maemo a ts'ebetso a le boima haholo kapa a sa lumelloeng. Fumana le ho lokisa sesosa.

• Sephetho sa relay switching se etsoa joalo ka khokahano e phaphametseng ea phetoho. Potoloho ena ea motlakase e sebetsa ho latela molao-motheo oa hona joale o khutsitseng, ke hore, relay e oela sebakeng se sa sebetseng ebe e tima sekontiri sa enjene leha ho ka ba le khefu ea kutlo kapa potoloho e bulehileng.

Khokahano ea yuniti ea trigger INT69 G
Hokela yuniti ea trigger INT69 G ho latela dia-gram ea potoloho. Sireletsa yuniti ea trigger ka fuse e liehang ho sebetsa (FC2) ea max. 4 A. E le ho netefatsa ts'ebetso ea ts'ireletso, kenya mochine oa trigger e le ntho ea pele ho potoloho ea matla a ho laola.

Lekanya potoloho ea BT1 le BT2 (sensor ea PTC) ha ea tlameha ho kopana le matla a kantletage. Sena se ka senya li-sensor tsa INT69 G le PTC.

Teko ea ts'ebetso ea yuniti ea trigger INT69 G
Pele o laela, ka mor'a ho rarolla mathata kapa ho etsa liphetoho ho potoloho ea matla a taolo, hlahloba ts'ebetso ea "trigger unit". Etsa tlhahlobo ena ka "continuity tester" kapa gage.

Gage naha	Relay boemo
Boemo bo sa sebetseng	11-12
Ho bulela INT69 G	11-14
Tlosa sehokelo sa PTC	11-12
Kenya sehokelo sa PTC	11-12
Seta bocha ka mor'a ho bulela lithapo tse kholo	11-14

Boemo ba ho fetisetsa INT69 G

Sefuthumatsi sa sump ea oli (lisebelisoa)
Ha konpresser e eme, sehatsetsi se kenella ka har'a oli e tlotsang ea matlo a li-compressor, ho latela khatello le mocheso o tikolohong. Sena se fokotsa matla a ho tlotsa a oli. Ha compressor e qala, sehatsetsi se ka har'a oli se fetoha mouoane ka ho fokotseha ha khatello. Liphello e ka ba ho phophoma le ho falla ha oli, ho baka tsitsipano ea oli tlas'a maemo a itseng.

Ts'ebetso:
Sefuthumatsi sa sump ea oli se sebetsa ha compressor e eme. Ha compres-sor e qala, heater ea sump ea oli e tima hape ka bo eona.

Khokahano:
Sefuthumatsi sa sump ea oli se tlameha ho hokeloa ka khokahanyo ea tlatsetso (kapa khokahanyo e ts'oanang ea wired auxil-iary) ea sehokelo sa compressor ho potoloho e arohaneng ea motlakase.

• El. lintlha: 115 V AC 60 Hz, 160 W.

Khokahano tseleng ea hajoale ea ketane ea taolo ea polokeho ha e lumelloe.

Capacity regulator (lisebelisoa)
Fuse (max. 3xlB ho latela IEC 60127-2-1) e tsamaellanang le hona joale e lekantsoeng e tlameha ho behoa ka pel'a khoele e 'ngoe le e' ngoe ea makenete ea taolo ea matla e le tšireletso ea potoloho e khutšoane. Leqtage ea fuse e tlameha ho lekana kapa e kholo ho feta bophahamo bo lekantsoengtage ea khoele ea makenete. Bokhoni ba ho tima li-fuse bo tlameha ho ba bo boholo ho feta kapa bo lekanang le boholo bo ka khonehang ba nako e khutšoanyane sebakeng sa ho kenya.

Khetho le ts'ebetso ea li-compressor tse nang le li-converter tsa maqhubu
Bakeng sa ts'ebetso e bolokehileng ea compressor, converter ea frequency e tlameha ho kenya ts'ebetso e feteletseng ea bonyane 140% ea boholo ba hona joale ba compressor (I-max.) bonyane metsotsoana e 3.

Ha u sebelisa li-converter tsa frequency, lintlha tse latelang li tlameha ho hlokomeloa:

1. Boholo bo lumelletsoeng ho sebetsa hona joale ba compressor (I-max) (sheba mofuta oa poleiti kapa data ea tekheniki) ha ea lokela ho fetisoa.
2. Haeba ho thothomela ho sa tloaelehang ho etsahala ka har'a sistimi, mefuta e amehang ea frequency converter e tlameha ho koaheloa ka nepo.
3. Phaello e phahameng ka ho fetisisa ea motlakase oa motlakase e tlameha ho ba kholo ho feta boholo ba hona joale ba compressor (I-max).
4. Etsa meralo le lits'ebetso ho latela melaoana ea ts'ireletso ea lehae le melao e tloaelehileng (mohlala, VDE) le melaoana hammoho le ho latela litlhaloso tsa moetsi oa frequency converter.

Lebelo la ho potoloha mefuta-futa	0 – f-min	f-min - f-max
E qalang nako	<1 s	ka. 4 s
Ho tima nako	hanghang

f-min/f-max bona khaolo ea 9: Lintlha tsa tekheniki: sebaka sa maqhubu se lumelletsoeng

Ho laela

Litokisetso tsa ho qala
Ho sireletsa compressor khahlanong le maemo a sa lumelloeng a ts'ebetso, lipalo-palo tsa khatello e phahameng le tse tlaase li tlamehile ka lehlakoreng la ho kenya.

Compressor e entse liteko fekthering mme mesebetsi eohle e lekoa. Ka hona, ha ho na litaelo tse khethehileng tsa ho sebetsa.

Sheba konpresser bakeng sa tšenyo ea lipalangoang!

Teko ea botšepehi ba khatello
Compressor e 'nile ea lekoa fekthering bakeng sa botšepehi ba khatello. Leha ho le joalo, haeba tsamaiso eohle e lokela ho ba tlas'a teko ea botšepehi ba khatello, sena se lokela ho etsoa ho latela UL 207 kapa maemo a ts'ireletso a ts'oanang ntle le ho kenngoa ha compressor.

Leak teko

KOTSI

Kotsi ea ho phatloha!
Compressor e tlameha ho hatelloa feela ka ho sebelisa nitrogen (N2). Le ka mohla u se ke ua hatella ka oksijene kapa likhase tse ling! Khatello e phahameng ka ho fetesisa e lumelletsoeng ea compressor ha ea lokela ho fetisoa ka nako efe kapa efe nakong ea tlhahlobo (sheba data ea poleiti ea mabitso)! Se ke oa kopanya sehatsetsi leha e le sefe le naetrojene kaha sena se ka etsa hore moeli oa ho tima o fetele sebakeng sa bohlokoa.

• Etsa tlhahlobo ea ho lutla setsing sa sehatsetsing ho latela UL 207 kapa maemo a ts'ireletso a ts'oanang, ha u ntse u shebile khatello e phahameng e lumelletsoeng ea compressor.

Pholoso

• U se ke ua qala compressor haeba e le tlas'a vacuum. U se ke ua sebelisa leha e le efe voltage - esita le bakeng sa liteko (e tlameha ho sebetsoa feela ka sehatsetsing).
• Tlas'a vacuum, bohole ba hona joale ba spark-over le creepage ea liboutu tsa khokahano ea boto ea terminal lia khutsufala; sena se ka fella ka ho senyeha ha boto ea matsoelintsoeke le terminal.
• Ntlha ea pele, tlosa tsamaiso 'me u kenye compressor ts'ebetsong ea ho tlosa.
• Fokotsa khatello ea compressor.
• Bula li-valve tsa ho koala le ho koala line ea khatello.
• Tlosa mahlakore a khatello ea ho hula le ho ntša metsi ka pompo ea vacuum.
• Qetellong ea ts'ebetso ea ho tsoa, ​​sekoti se lokela ho ba <1.5 mbara (0.02 psia) ha pompo e tima.
• Pheta ts'ebetso ena hangata kamoo ho hlokahalang.

Tefiso ea sehatsetsing

TLHOKOMELO
Apara liaparo tsa boitšireletso tse kang likhalase le liatlana tse itšireletsang!

• Etsa bonnete ba hore li-valve tsa ho koala le tsa khatello li bulehile.
• Ha konpresser e tima, eketsa sehatsetsi sa metsi ka ho toba ho condenser kapa receiver, ho senya vacuum.
• Haeba sehatsetsi se hloka ho phahamisoa ka mor'a ho qala kompressor, se ka phahamisoa ka mokhoa oa mouoane ka lehlakoreng la ho huloa, kapa, ho nka mehato e loketseng ea ho itšireletsa, hape ka mokhoa oa mokelikeli sebakeng se kenang ho mouoane.

TSEBISO

• Qoba ho tlatsa sistimi ka sehatsetsing!
• Ho qoba ho fetoha ha maikutlo, metsoako ea sehatsetsi sa zeotropic e tlameha ho tlatsoa feela ka sehatsetsing ka sebopeho sa mokelikeli.
• Se ke oa tšela se pholileng ka metsi ka valve ea ho monya holim'a compressor.
• Ha ho lumelloe ho kopanya li-additives le oli le sehatsetsing.

E qalang

TLHOKOMELO
Netefatsa hore li-valve tse koalang ka bobeli li bulehile pele u qala komporo!

• Sheba hore lisebelisoa tsa polokeho le ts'ireletso (switch switch, ts'ireletso ea koloi, mehato ea ts'ireletso ea likhokahano tsa motlakase, joalo-joalo) kaofela li sebetsa hantle.
• Tlosa compressor 'me u lumelle ho sebetsa bonyane metsotso e 10.
• Sheba boemo ba oli ka: Oli e tlameha ho bonahala ka khalase ea pono.

Haeba palo e kholo ea oli e tlameha ho eketsoa, ​​​​ho na le kotsi ea litlamorao tsa hamore ea oli.

Haeba ho joalo, hlahloba ho khutla ha oli!

Ho qoba slugging

• Slugging e ka senya compressor mme ea etsa hore sehatsetsi se lutle.

Ho thibela slugging:

• Sistimi e felletseng ea lihatsetsi e tlameha ho etsoa ka nepo.
• Likarolo tsohle li tlameha ho lekanngoa ka tsela e lumellanang mabapi le tlhahiso (haholo-holo evaporator le li-valve tsa ho atolosa).
• Mocheso o matla oa khase ea suction ha o kenya compressor o lokela ho ba min. 7 - 10 K. (hlahloba boemo ba valve ea ho atolosa).
• Tsamaiso e tlameha ho fihla boemong ba tekano.
• Haholo-holo lits'ebetsong tse mahlonoko (mohlala, lintlha tse 'maloa tsa mouoane), mehato e khothaletsoa joalo ka ho nkela maraba a metsi, valve ea solenoid moleng oa mokelikeli, jj.
• Ha hoa lokela ho ba le motsamao oa se pholileng leha e ka ba ofe ha konpresser e ntse e eme.

Tlhokomelo

Tokisetso
Pele o qala mosebetsi ofe kapa ofe oa compressor:

• Tlosa compressor 'me u e sireletse ho thibela ho qala bocha.
• Fokotsa compressor ea khatello ea sistimi.
• Thibela moea ho kena ka har'a sistimi!

Ka mor'a hore tlhokomelo e etsoe:

• Hokela senotlolo sa polokeho.
• Tlosa compressor.
• Lokolla switch lock.

Mosebetsi o tlameha ho etsoa
E le ho netefatsa ts'epo e nepahetseng ea ts'ebetso le bophelo ba ts'ebeletso ea compressor, re khothaletsa ho etsa mosebetsi oa ho fana le ho hlahloba nako le nako:

Ho fetola oli: 

• ha e tlamehe bakeng sa litsamaiso tse hlahisoang ke feme.
• bakeng sa lits'ebetso tsa masimong kapa ha o sebetsa haufi le moeli oa kopo: ka lekhetlo la pele kamora lihora tse 100 ho isa ho tse 200 tsa ts'ebetso, ebe hoo e ka bang. lilemo tse ling le tse ling tse 3 kapa lihora tse 10,000 - 12,000 tsa ts'ebetso. Lahla oli e sebelisitsoeng ho latela melaoana; hlokomela melao ea naha.

Licheke tsa selemo:
Boemo ba oli, ho dutla ho thata, lerata le mathang, likhatello, mocheso, ts'ebetso ea lisebelisoa tse thusang joalo ka heater ea sump ea oli, switch switch.

Litlhahiso tsa likarolo tse ling / lisebelisoa

Likarolo tse ling tse fumanehang le lisebelisoa li ka fumanoa sesebelisoa sa rona sa khetho sa compressor tlas'a vap.bock.de hammoho le bockshop.bock.de.

Sebelisa likarolo tsa 'nete tsa Bock feela!

Lisebelisoa / oli
Mofuta oa oli o tlatsitsoeng joalo ka maemo fekthering o tšoailoe letlapeng la mabitso, 'me sena se lokela ho sebelisoa kamehla, esita le maemong a litsi tsa tlhokomelo. Mefuta e meng ea oli e ka fapana haholo ka boleng ka lebaka la li-additives kapa lisebelisoa tse tlase tse tala tse entsoeng ke moetsi. Ho netefatsoa ka har'a li-compressor ho ke ke ha netefatsoa, ​​haeba ho sebelisoa mefuta e meng ea oli. Ke ka lebaka lena, hore re khothaletsa feela tšebeliso ea oli e tsoang ho Bock! Bock ha e nke boikarabello bakeng sa tšenyo leha e le efe e bakoang ke mefuta e meng ea oli.

• Mofuta o tloaelehileng oa oli oa Bock: BOCK lub E55

Ho tlosa
Koala li-valve tse koalang holim'a compressor. Hlakola sehatsetsing (ha sea lokela ho ntšoa tikolohong) 'me u se lahle ho latela melaoana. Ha konpresser e tepeletse maikutlo, hlakola li-screws tsa li-valve tse koalang. Tlosa compressor u sebelisa sehole se loketseng. Lahla oli ka hare ho latela melaoana e sebetsang ea naha.

Lisebelisoa

Taolo ea bokhoni

TLHOKOMELO
Haeba taolo ea matla e kentsoe fekthering, karolo ea taolo (valve ea sefofane) e kenngoa ebe e hokahanngoa ke moreki.

Pele o qala, tlosa sekoahelo ho sesebelisoa sa matla 'me u se nkele sebaka sa taolo e kentsoeng (valve ea sefofane). Ela hloko! Compressor e tlas'a khatello!Depressurize ea compressor pele. Screw in control unit (valve ea sefofane) e nang le selikalikoe sa tiiso 'me e tiile ka 15 Nm. Mahlakoreng a likhoele tse metsi ka oli ea ester. Kenya khoele ea makenete, e tlamelle ka knurled nut mme o e kopanye.

TLHOKOMELISO:
Balaoli ba 'maloa ba matla ha ba khone ho fetoha ka nako e le' ngoe nakong ea ts'ebetso ea compressor! Ho seng joalo phetoho ea tšohanyetso ea mojaro e ka senya compressor! Latela nako ea ho fetoha ea 60 s.

Latela le tatellano ea switching:

• E fetola LR1 60s LR2
• E tima LR2 60s LR1

TSEBISO

• Ts'ebetso e laoloang ke bokhoni e fetola lebelo la khase le likhatello tsa khatello ea setsi sa sehatsetsing: Lokisa tsela ea ho hula le boholo ka tsela e nepahetseng, u se ke ua beha linako tsa taolo haufi haholo 'me u se ke ua lumella sistimi hore e fetohe ho feta makhetlo a 12 ka hora. ba fihletse boemo ba tekano). Ts'ebetso e tsoelang pele taolong ea stage ha e khothalletsoe kaha lebelo la khase tsamaisong ea polante tlas'a maemo a itseng ha le tiise hore oli e lekaneng e tla khutlela ho compressor e nang le matla a ho laola matla. Re khothaletsa ho fetohela ts'ebetsong e sa laoleheng (100% caac-ity) bonyane metsotso e 5 ka hora e laolehileng ea ts'ebetso. Ho khutlisa oli e tiisitsoeng ho ka boela ha etsoa ka tlhokahalo ea matla a 100% ka mor'a hore compressor e 'ngoe le e 'ngoe e qale bocha.
• Ts'ebetso ea motlakase ea valve ea solenoid: Ka tloaelo e bulehile, (corre-sponds ho 100% ea matla a compressor).
• Bakeng sa taolo ea bokhoni ba dijithale bona tokomane 09900.

Lisebelisoa tse khethehileng li kentsoe pele fekthering haeba li laetsoe ka ho khetheha ke moreki. Retrofitting e ka khoneha ka ho latela ka botlalo litaelo tsa polokeho le litaelo tsa tokiso tse kentsoeng ka lisebelisoa. Tlhahisoleseding e mabapi le ts'ebeliso, ts'ebetso, tlhokomelo le ts'ebeletso ea likaroloana e fumaneha libukeng tse hatisitsoeng kapa marang-rang tlasa vap.bock.de.

Sekhetho sa oli
Ho thella ha oli ho ka baka tšenyo ho compressor.

Ho thibela ho ruruha ha oli:

• Ho khutla ha oli ho tloha karohanong ea oli ho tlameha ho tataisoa ho khutlela khokahanyong e reriloeng (D1) ntlong ea compressor.
• Ho khutlisa oli e tobileng moleng oa ho monya ho tloha searolanong sa oli ha ho lumelloe.
• Netefatsa hore karohano ea oli e lekantsoe hantle.

Molaoli oa boemo ba oli
Sistimi ea taolo ea boemo ba oli e ipakile e le li-circuits tse bapileng tsa li-compressor tse 'maloa. Khokahano "0" e fanoa bakeng sa ho kenya molaoli oa boemo ba oli (sheba setšoantšo sa litekanyo). Litaolo tsohle tse tloaelehileng tsa mochini oa oli ho tloha AC & R, ESK, Carly hammoho le tsamaiso ea taolo ea boemo ba oli ea elektronike ho tloha AC & R, Teklab, OM3 TraxOil ho tloha Alco le ESK (phetolelo e telele feela) e ka kopanngoa ka ho toba ntle le li-adapter (bona setšoantšo sa 21). Galase ea pono holim'a taolo ea boemo ba oli ha e hlokehe.

Kopano e etsoa sebakeng sa pele sa khalase e tloaelehileng ea pono (bona setšoantšo sa 22).

Lintlha tsa tekheniki

Mofuta     UL-HGX66e/	No. ea lisilindara	Ho falla (1450 rpm / 1740 rpm)	Motlakase data     3					Boima ba 'mele	Lihokelo 4		Oli tefiso (mohlala sebetsa)	Oli tefiso (pono khalase setsi)
			1	2	2	Ho qala jwale (rotor notletsoe)	lumelloa sekhahla sa maqhubu		Hlakola mola DV	Ho hula mola SV
		50 Hz 60 Hz		PW 1+2		PW 1/PW 1+2
			V	A	kW (HP)	A	Hz	lb	mm (inch)	mm (inch)	ltr (fl.oz)	ltr (fl.oz)
		cfh
1340 ML 31	6	4115 4938	380-420 VY/YY - 3 - 50 Hz PW 440-480 VY/YY - 3 - 60 Hz PW PW = Karolo e Phethahalang, Karo-karolelano ea Maqhubu: 50%/50%	54	31,9 (43,4)	170/275	25 - 60	671	EA-42 (1 5/8)	54 (2 1/8)	4.4 (155)	3.8 (134)
1340 S 37		4115 4938		65	38,1 (51,8)	196/335		678
1540 ML 36		4724 5668		62	37,2 (50,6)	170/275		666
1540 S 42		4724 5668		75	44,4 (60,4)	196/335		673
1750 ML 44		5374 6449		72	42,4 (57,6)	196/335		656
1750 S 50		5374 6449		87	50,7 (68,9)	222/361		677
2070 ML 50		6356 7627		85	50,7 (68,9)	196/335		680		64 (2 5/8)
2070 S 60		6356 7627		103	60,7 (82,5)	222/361		691

1. Mamello (± 10%) e amanang le boleng bo tloaelehileng ba voltage range. Karolo e 'ngoetages le mefuta ea hona joale ka kopo.
2. Litlhaloso tsa max. tšebeliso ea matla e sebetsa bakeng sa ts'ebetso ea 60Hz
   1. Nahana ka max. e sebetsang hajoale / max. tšebeliso ea matla bakeng sa moralo oa li-fuse, likhoele tsa phepelo le lisebelisoa tsa polokeho.
      Tsoaka: Sehlopha sa tšebeliso AC3
3. Litlhaloso tsohle li ipapisitse le karolelano ea voltage fapaneng
4. Bakeng sa likhokahano tsa solder

Litekanyo le likhokahano

UL-HGX66e

SV DV	Suction line bona data ea tekheniki, khaolo ea 9 Mohala oa ho tsoa
A	Lehlakore la khokahanyo, ha le notleloe	1/8" NPTF
A1	Lehlakore la ho hula la kgokelo, le notlellwang	7/16 “UNF
B	Lehlakore la ho lahla khokahanyo, ha le notleloe	1/8" NPTF
B1	Lehlakore la ho lahla la khokahanyo, le notlelloa	7/16 “UNF
C	Connection oli khatello ea tšireletso switch OIL	1/8" NPTF
D	Connection oli khatello ea tšireletso switch LP	7/16 “UNF
D1	Ho khutla ha oli ea khokahanyo ho tloha karohanong ea oli	1/4" NPTF
F	Sekhahla sa oli	M12x1.5
H	Plaka ea tefiso ea oli	1/4" NPTF
J	Ho kopanya oli ea ho futhumatsa sump	3/8" NPTF
K	Khalase e bonang	3 x M6
L	Khokahano ea thermostat ea tšireletso ea mocheso	1/8" NPTF
M	Sesefa sa oli	M12x1.5
O	Taolo ea boemo ba oli ea khokahano	3 x M6
P	Sensor e fapaneng ea khatello ea oli ea khokahano	M20x1.5
ÖV	Seqhubu sa tšebeletso ea oli ea khokahanyo	1/4" NPTF
Q	Sensor ea mocheso oa oli ea khokahano	1/8" NPTF
W	Khokahano bakeng sa ente ea sehatsetsing	2x 1/8" NPTF

Phatlalatso ea ho kenyeletsoa

Phatlalatso ea ho kenngoa ha mochini o sa fellang ho latela EC Machinery Directive 2006/42/EC, Annex II 1. B

Moetsi:

Bock GmbH
Benzstraße 7 72636 Frickenhausen, Jeremane.

Rona, joalo ka moetsi, re phatlalatsa ka boikarabello ba hore mochini o sa phethahalang

Lebitso: 

Mefuta:
Semi-hermetic compressor

• HG(X)12P/60-4 S (HC) ………………………HG(X)88e/3235-4(S) (HC)
• UL-HGX12P/60 S 0,7…………………………… UL-HGX66e/2070 S 60
• HGX12P/60 S 0,7 LG ………………………….. HGX88e/3235 (ML/S) 95 LG
• HG(X)22(P)(e)/125-4 A ……………………… HG(X)34(P)(e)/380-4 (S) A
• HGX34(P)(e)/255-2 (A) …………………….. HGX34(P)(e)/380-2 (A)(K)
• HA(X)12P/60-4 ……………………………… HA(X)6/1410-4
• HAX22e/125 LT 2 LG ………………………. HAX44e/665 LT 14 LG
• HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
• UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
• HGX12/20-4 (ML/S/SH) CO2T………….. HGX46/440-4 (ML/S/SH) CO2 T
• UL-HGX12/20 ML(P) 2 CO2T…………. UL-HGX46/440 ML(P) 53 CO2T
• HGZ(X)7/1620-4 ……………………………. HGZ(X)7/2110-4
• HGZ(X)66e/1340 LT 22……………………… HGZ(X)66e/2070 LT 35
• HRX40-2 CO2 TH…………………………….. HRX60-2 CO2 TH
• Lebitso: Bula mofuta oa compressor
• Mefuta:
  • F(X)2 ……………………………………… F(X)88/3235 (NH3)
  • FK(X)1…………………………………….. FK(X)3
  • FK(X)20/120 (K/N/TK)…………….. FK(X)50/980 (K/N/TK)

e lumellana le lipehelo tse latelang tsa Taelo e boletsoeng ka holimo:
Ho ea ka Annex I, lintlha 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.3, 1.3.7, 1.5.1, 1.5.2, 1.5.13 le 1.7.1 ho 1.7.4 ( ntle le 1.7.4 f) li phethahala.

Ho sebelisoa litekanyetso tse lumellanang, haholo-holo:

• TS EN ISO 12100 Tšireletseho ea mochini - Melao-motheo e akaretsang ea moralo - Tekolo ea kotsi le phokotso ea likotsi.
• TS EN 12693 Sistimi ea sehatsetsi le lipompo tsa mocheso - Litlhoko tsa polokeho le tikoloho - Li-compressor tse ntle tsa sehatsetsi

Maikutlo:

• Re boetse re phatlalatsa hore litokomane tse khethehileng tsa tekheniki tsa mochini ona o sa fellang li entsoe ho latela Annex VII, Karolo ea B, 'me re tlamehile ho fana ka tsena ka kopo e utloahalang ho tsoa ho balaoli ba naha ka bomong ka ho fetisetsa boitsebiso.
• Komisi e thibetsoe ho fihlela ho netefalitsoe hore mochini oo mochini o sa fellang ka holimo o tla kengoa ho ona o lumellana le EC Machinery Directive le EC Declaration of Conformity, Annex II. 1. A e teng.

Motho ea nang le tumello ea ho hlophisa le ho fana ka litokomane tsa tekheniki:

Bock GmbH
Alexander Layh Benzstraße 7 72636 Frickenhausen, Jeremane.

Frickenhausen, la 04 Pherekhong 2021

Phatlalatso ea ho kenyeletsoa ha mechini e seng e phethiloe ho latela melaoana ea UK Statutory Instrument Supply of Machinery (Safety) 2008, Annex II 1. B.

Moetsi:
Bock GmbH Benzstraße 7 72636 Frickenhausen, Jeremane.

Rona, joalo ka moetsi, re phatlalatsa ka boikarabello ba hore mochini o phethiloeng ka karolo e 'ngoe

• Lebitso:
  • Semi-hermetic compressor
• Mefuta:
  • HG(X)12P/60-4 S (HC) ………………………HG(X)88e/3235-4(S) (HC)
  • UL-HGX12P/60 S 0,7…………………………… UL-HGX66e/2070 S 60
  • HGX12P/60 S 0,7 LG ………………………….. HGX88e/3235 (ML/S) 95 LG
  • HG(X)22(P)(e)/125-4 A ……………………… HG(X)34(P)(e)/380-4 (S) A
  • HGX34(P)(e)/255-2 (A) …………………….. HGX34(P)(e)/380-2 (A)(K)
  • HA(X)22e/125-4 …………………………….. HA(X)6/1410-4
  • HAX22e/125 LT 2 LG ………………………. HAX44e/665 LT 14 LG
  • HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
  • UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
  • HGX12/20-4 (ML/S/SH) CO2T………….. HGX46/440-4 (ML/S/SH) CO2 T
  • UL-HGX12/20 ML(P) 2 CO2T…………… UL-HGX46/440 ML(P) 53 CO2T
  • HGZ(X)7/1620-4 ……………………………. HGZ(X)7/2110-4
  • HGZ(X)66e/1340 LT 22……………………… HGZ(X)66e/2070 LT 35
  • HRX40-2 CO2 TH…………………………….. HR(Z)X60-2 CO2 T (H)(V)
• Lebitso: Bula mofuta oa compressor
• Mefuta:
  • F(X)2 ……………………………………………… F(X)88/3235 (NH3)
  • FK(X)1…………………………………………….. FK(X)3
  • FK(X)20/120 (K/N/TK)……………………….. FK(X)50/980 (K/N/TK)
• Nomoro ea serial: BC00000A001 - BN99999Z999

e tsamaellana le lipehelo tse latelang tsa sesebelisoa sa Molao se boletsoeng ka holimo:

• Ho ea ka Schedule 2, part1, lintlha 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.3, 1.3.7, 1.5.1, 1.5.2, 1.5.13 le 1.7.1 ho 1.7.4. 1.7.4 (ntle le XNUMX f) lia phethahala.

Litekanyetso tse khethiloeng:

• TS EN ISO 12100 Tšireletseho ea mochini - Melao-motheo e akaretsang ea moralo - Tekolo ea kotsi le phokotso ea likotsi.
• TS EN 12693 Sistimi ea sehatsetsi le lipompo tsa mocheso - Litlhoko tsa polokeho le tikoloho - Li-compressor tse ntle tsa sehatsetsi

Maikutlo:

• Re boetse re phatlalatsa hore litokomane tse khethehileng tsa tekheniki tsa mochini ona o seng o phethiloe o entsoe ho latela Sehlomathiso II, 1. B 'me re tlamehile ho fana ka tsena ka kopo e utloahalang ho tsoa ho balaoli ba naha ka bomong ka ho fetisetsa data.
• Ho romelloa ho thibetsoe ho fihlela ho netefalitsoe hore mochine oo karolo e 'ngoe e tlatsitsoeng ka holimo e tla kenngoa ho oona o lumellana le melaoana ea UK Statutory Instrument Supply machinery (Safety) 2008 le EC Declaration of Conformity, Annex II, 1. A e teng.

Motho ea nang le tumello ea ho hlophisa le ho fana ka litokomane tsa tekheniki:

Bock GmbH
Alexander Layh Benzstraße 7 72636 Frickenhausen, Jeremane.

Frickenhausen, la 14 Mphalane 2022

UL-Setifikeiti sa Tumellano

Moreki ea ratehang,
Setifikeiti sa Tumellano se ka khoasolloa ka QR-Code e latelang:

https://vap.bock.de/stationaryapplication/Data/DocumentationFiles/UL-Certificateofconformity.pdf

Danfoss A / S
Tharollo ea Boemo ba Leholimo • danfoss.us • +1 888 326 3677 • heat.cs.na@danfoss.com.

Tlhahisoleseding efe kapa efe, ho kenyeletswa, empa e sa felle feela ho tlhahisoleseding e mabapi le kgetho ya sehlahiswa, tshebediso ya sona kapa tshebediso ya sona, moralo wa sehlahiswa, boima, boholo, bokgoni kapa datha efe kapa efe ya tekheniki e dibukeng tsa dihlahiswa, dipapatso, jj le hore na di fumaneha ka mongolo, ka molomo, ka mokhoa oa elektronike, inthaneteng kapa ka ho khoasolla, e tla nkoa e le tsebo, 'me e tlama feela haeba le ho isa bohōleng boo, ho buuoa ka mokhoa o hlakileng ka khotheishene kapa netefatso ea taelo. Danfoss e ke ke ea amohela boikarabello bofe kapa bofe bakeng sa liphoso tse ka bang teng libukeng, libukana, livideo le lintho tse ling. Danfoss e na le tokelo ea ho fetola lihlahisoa tsa eona ntle le tsebiso. Sena se sebetsa le ho lihlahisoa tse otarang empa li sa tlisoa ha feela liphetoho tse joalo li ka etsoa ntle le liphetoho sebopeho, ho lekana kapa tšebetso ea sehlahisoa.

Matšoao 'ohle a thepa ena ke thepa ea lik'hamphani tsa Danfoss A/S kapa tsa Danfoss. Danfoss le logo ea Danfoss ke matšoao a khoebo a Danfoss A/S. Litokelo tsohle li sirelelitsoe.

© Danfoss | Litharollo tsa Tlelaemete | 2023.07.

Litokomane / Lisebelisoa

Danfoss UL-HGX66e Reciprocating Compressor [pdf] Tlhophiso Tataiso UL-HGX66e Reciprocating Compressor, UL-HGX66e, Compressor Reciprocating, Compressor

Litšupiso

• Bukana ea Mosebelisi