Danfoss UL-HGX66e Mai Rarraba Compressor
Bayanin samfur
The Reciprocating Compressor na'ura ce mai matsi da ake amfani da ita don firiji. Ya zo cikin samfura daban-daban tare da ƙayyadaddun bayanai daban-daban:
- UL-HGX66e/1340 ML 31
- UL-HGX66e/1540 ML 36
- UL-HGX66e/1750 ML 44
- UL-HGX66e/2070 ML 50
- UL-HGX66e/1340S 37
- UL-HGX66e/1540S 42
- UL-HGX66e/1750S 50
- UL-HGX66e/2070S 60
Umarnin Amfani da samfur
Tsaro
Yana da mahimmanci a kiyaye umarnin aminci don hana hatsarori da munanan raunuka:
- Karanta kuma bi duk umarnin aminci da aka bayar a cikin littafin.
- Kada a haɗa ko amfani da kwampreso ba daidai ba.
- Kula da duk alamun amincin samfur.
- Koma zuwa lambobin ginin gida don buƙatun shigarwa.
Haɗin lantarki
Littafin yana ba da bayani game da haɗin wutar lantarki na compressor:
- Gabaɗaya kariya ta aminci don haɗin lantarki.
- Bayani don lambar sadarwa da zaɓin lamba na mota.
- Zane-zane na kewaya don nau'ikan fara mota daban-daban.
- Umarnin haɗi don naúrar faɗakarwa ta lantarki INT69 G.
- Gwajin aikin naúrar jawo INT69 G.
- Na'urorin haɗi na zaɓi kamar na'urar dumama mai da mai sarrafa ƙarfi.
- Zaɓi da aiki na compressors tare da masu juyawa mita.
Bayanan Fasaha
Littafin yana ba da ƙayyadaddun fasaha na compressor:
- Bayani akan sigogi na lantarki da na inji.
Girma da Haɗin kai
Littafin yana ba da girma da bayanin haɗin kai don kwampreso:
- Girman jiki na kwampreso.
- Abubuwan haɗi da buƙatun.
Sanarwa na Ƙaddamarwa
Littafin ya ƙunshi sanarwar haɗawa don kwampreso:
- Sanarwa na hukuma da ke bayyana bin ƙa'idodi da ƙa'idodi masu dacewa.
UL-Takaddar Yardawa
Littafin ya haɗa da UL- Certificate of Compliance don compressor:
- Takaddun shaida na hukuma wanda ke nuna bin ka'idodin UL.
Gabatarwa
hadari
Hadarin haɗari.
Na'urar damfara da injinan firji ne da ake matsa lamba kuma don haka kira don ƙara taka tsantsan da kulawa cikin kulawa.
Haɗin da ba daidai ba da amfani da kwampreta na iya haifar da mummunan rauni ko kuma m!
- Don guje wa mummunan rauni ko mutuwa, kiyaye duk umarnin aminci da ke ƙunshe a cikin waɗannan umarnin kafin haɗuwa da kafin amfani da kwampreso! Wannan zai kauce wa rashin fahimtar juna kuma ya hana mummunan rauni da lalacewa!
- Kar a taɓa yin amfani da samfurin ba daidai ba amma kawai kamar yadda wannan jagorar ya ba da shawarar!
- Kula da duk alamun amincin samfur!
- Koma zuwa lambobin ginin gida don buƙatun shigarwa!
Canje-canje marasa izini da gyare-gyare ga samfurin da wannan jagorar ba ta rufe su ba an hana su kuma za su ɓata garanti!
Wannan jagorar koyarwa wani yanki ne na wajibi na samfurin. Dole ne ya kasance samuwa ga ma'aikatan da ke aiki da kula da wannan samfurin. Dole ne a wuce zuwa abokin ciniki na ƙarshe tare da naúrar da aka shigar da compressor. Wannan takaddar tana ƙarƙashin haƙƙin mallaka na BOCK GmbH, Jamus. Bayanin da aka bayar a cikin wannan jagorar yana iya canzawa da haɓakawa ba tare da sanarwa ba.
Tsaro
Gano umarnin aminci
- Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai haifar da kisa ko mummunan rauni nan da nan.
- Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai iya haifar da mutuwa ko mummunan rauni.
- Yana nuna yanayi mai haɗari wanda, idan ba a kauce masa ba, zai iya haifar da mummunan rauni ko ƙananan rauni.
- Yana nuna yanayin da, idan ba a kauce masa ba, zai iya haifar da lalacewar dukiya.
- Muhimmiyar bayanai ko shawarwari akan sauƙaƙe aiki.
Gabaɗaya umarnin aminci
Gargadi
Hadarin haɗari.
Na'urar damfara da injinan firji ne da ake matsa lamba kuma don haka kira don ƙara taka tsantsan da kulawa cikin kulawa.
Matsakaicin halatta wuce gona da iri ba dole ba ne a wuce shi, koda don dalilai na gwaji!
Hadarin konewa!
- Dangane da yanayin aiki, ana iya kaiwa ga yanayin zafi sama da 140°F (60°C) a gefen fitarwa ko ƙasa da 32°F (0°C) a gefen tsotsa.
- Dole ne a guji tuntuɓar na'urar sanyaya. Tuntuɓar na'urar sanyaya na iya haifar da ƙonewa mai tsanani da lalacewar fata.
Amfani da niyya
Gargadi
Maiyuwa ba za a yi amfani da kwampreta a cikin mahalli masu yuwuwar fashewa ba!
- Waɗannan umarnin taro sun bayyana daidaitaccen nau'in kwampreso mai suna a cikin taken da Bock ya kera. Bock compressors an yi niyya don shigarwa a cikin injin injin (a cikin EU bisa ga Dokokin EU 2006/42/EC Directive Machinery, 2014/68/EU Umarnin Kayan Aikin Matsi, a wajen EU bisa ga ƙa'idodin ƙasa da jagororin). .
Yin aiki yana halatta kawai idan an shigar da kwampreso daidai da waɗannan umarnin-sembly kuma an bincika dukkan tsarin da aka haɗa shi kuma an amince da shi daidai da ƙa'idodin doka.
An yi nufin compressors don amfani a cikin tsarin firiji don dacewa da iyakokin aikace-aikace. Na'urar firji da aka ƙayyade a cikin waɗannan umarnin kawai za a iya amfani da su.
An haramta duk wani amfani da kwampreso!
Abubuwan da ake buƙata na ma'aikata
Rashin cancantar ma'aikata yana haifar da haɗarin haɗari, sakamakon zama mai tsanani ko rauni. Don haka an keɓance aiki akan compressors don ma'aikatan da suka cancanci yin aiki akan tsarin firiji mai matsa lamba:
- Don misaliample, ƙwararren injin firji, ko injiniyan injin firiji. Kazalika da sana'o'i tare da kwatankwacin horon da ke baiwa ma'aikata damar haɗawa, girka, kulawa da gyara na'urorin sanyi da na'urorin sanyaya iska. Dole ne ma'aikata su kasance masu iya tantance aikin da za a gudanar da kuma gane duk wani haɗari mai haɗari.
Bayanin Samfura
Takaitaccen bayanin
- Semi-hermetic shida-Silinda mai mayar da kwampreso tare da tsotsa-gas sanyaya injin tuƙi.
- Rafin refrigerant da aka tsotse daga cikin injin da ke kwararowa akan motar kuma yana sanyaya shi sosai. Ta wannan hanya, ana iya ajiye motar a ƙananan zafin jiki, musamman a ƙarƙashin manyan lodi.
Ana iya samun girman girman da ƙimar haɗin kai a babi na 10.
Farantin suna (misaliample)
Nau'in maɓalli (misaliample)
- HG - Gas mai sanyaya (mai sanyaya gas)
- X - cajin mai na Ester
- S - Mota mafi ƙarfi
- ML - Motoci don sanyaya na yau da kullun da daskarewa mai zurfi
Yankunan aikace-aikace
Masu firiji
| HFC + gauraye | R134A, R404A/R507 |
| Haɗin HFC/HFO | R448A, R449A, R450A, R513A |
Ƙarin bayani game da firjin da aka amince akan kayan aikin zaɓi na Bock compressor VAP (vap.bock.de).
Kudin mai
- Ana cika kwampressors a masana'anta da nau'in mai kamar haka: BOCK lub E55
Don sake cikawa, muna ba da shawarar nau'ikan mai na sama. Duba kuma sashe na 7.4.
SANARWA
Matsayin mai dole ne ya kasance a cikin ɓangaren gani na gilashin gani; lalacewa ga kwampreso yana yiwuwa idan an cika shi ko ƙasa!
Iyaka na aikace-aikace
SANARWA
Ayyukan damfara yana yiwuwa a cikin iyakokin aiki. Ana iya samun waɗannan a cikin kayan zaɓin zaɓi na Bock compressor (VAP) ƙarƙashin vap.bock.de. Kula da bayanin da aka bayar a can.
- Halatta zazzabi na yanayi: -20°C…+60°C (-4°F…140°F)
- Max. halaltaccen zazzabi ƙarshen fitarwa 140°C (284°F).
- Max. halatta mitar sauyawa 12x/h.
- Mafi ƙarancin lokacin gudu na 3 min. Dole ne a cimma daidaiton yanayin (aiki na ci gaba).
Don aiki tare da ƙarin sanyaya:
- Yi amfani da mai kawai tare da babban kwanciyar hankali na thermal.
- Guji ci gaba da aiki kusa da bakin kofa.
- Za a iya buƙatar rage zafin zafin zafin gas ɗin mai zafi ko saita shi daban-daban yayin aiki kusa da bakin kofa.
Don aiki tare da mai sarrafa ƙarfin aiki:
- Ci gaba da aiki, lokacin da aka kunna mai sarrafa ƙarfin aiki, baya halatta kuma yana iya haifar da lahani ga kwampreso.
- Za a iya buƙatar rage zafin zafin zafin gas ɗin mai zafi ko saita shi daban-daban yayin aiki kusa da bakin kofa.
- Lokacin da aka kunna mai sarrafa ƙarfin, saurin iskar gas a cikin tsarin ba zai iya a ƙarƙashin wasu yanayi ba don tabbatar da cewa an dawo da isasshen mai zuwa ga kwampreso.
Don aiki tare da mai sauya mitar:
- Matsakaicin halin yanzu da amfani da wutar lantarki ba dole ba ne a wuce shi. A cikin yanayin aiki sama da mitar mains, iyakar aikace-aikacen za a iya iyakance shi (max. (max. 60 Hz) 60 Hz).
Lokacin aiki a cikin kewayon injin, akwai haɗarin iska ta shiga ta gefen tsotsa. Wannan na iya haifar da halayen sinadarai, hawan matsin lamba a cikin na'urar da kuma matsananciyar zafin iskar gas. Hana shigowar iska ta kowane hali!
- Matsakaicin mitar da aka yarda: 60 Hz
- Matsakaicin matsi na aiki (LP/HP) 1): 19/28 barg (276/406 psig)
- LP = Ƙananan matsa lamba
- HP = Babban matsa lamba
Compressor taro
Sabbin kwampressors suna cike da masana'anta da iskar gas mara amfani. Ka bar wannan cajin sabis ɗin a cikin kwampreso har tsawon lokacin da zai yiwu kuma kafin shigar da iska. Bincika compressor don lalacewar sufuri kafin fara kowane aiki.
Adana da sufuri
- Adana a -30°C…+70°C (-22°F…+158°F), matsakaicin halaltaccen zafi na dangi 10% – 95%, babu tauri
- Kada a adana a cikin gurɓataccen yanayi, ƙura, tururi ko a cikin mahalli mai saurin fashewa.
- Yi amfani da gashin ido na sufuri.
- Kar a ɗaga da hannu!
- Yi amfani da kayan ɗagawa!
Saita
Haɗe-haɗe (misali masu riƙe bututu, ƙarin raka'a, sassa masu ɗaure, da sauransu) kai tsaye zuwa kwampreso ba su halatta ba!
- Samar da isasshen izini don aikin kulawa.
- Tabbatar da isassun iskar compressor.
- Kada a yi amfani da shi a cikin gurɓataccen abu, mai ƙura, damp yanayi ko yanayi mai ƙonewa.
- Saita akan madaidaici ko firam tare da isassun ƙarfin ɗaukar kaya.
- Single kwampreso zai fi dacewa akan jijjiga damper.
- Duplex da layi daya da'irori ko da yaushe m.
- Ana ba da shawarar shigar da muffler girgiza bututu!
Hanyoyin haɗin bututu
Lalacewa mai yiwuwa.
Kar a sayar da shi muddin na'urar tana cikin matsin lamba. Superheating na iya lalata bawul. Cire goyan bayan bututu don haka daga bawul don siyar da shi don haka sanyaya jikin bawul yayin da bayan siyarwar. Solder kawai ta amfani da iskar gas don hana samfuran iskar shaka (ma'auni).
- Ana samun haɗin bututu akan kwampreso don siyarwa ko walda (na'urorin haɗi). Fitar da bawul ɗin layin tsotsa sun gama karatu a cikin diamita ta yadda za a iya amfani da bututu masu daidaitattun girman millimita da inch. Za a nutsar da bututu fiye ko žasa da zurfi bisa ga girma.
- Ana ƙididdige diamita na haɗin haɗin bawul ɗin kashewa don mafi girman fitarwar kwampreso. Dole ne a daidaita sashin giciye na bututun da ake buƙata da fitarwa. Hakanan ya shafi bawuloli marasa dawowa.
Bututu
- Bututu da sassan tsarin dole ne su kasance masu tsabta da bushewa a ciki kuma marasa ma'auni, swarf da yadudduka na tsatsa da phosphate. Yi amfani da sassa masu hana iska kawai.
- Sanya bututu daidai. Dole ne a samar da madaidaitan ma'aunin girgiza don hana fasa bututu da karye ta hanyar girgiza mai tsanani.
- Tabbatar da dawowar mai daidai.
- Ci gaba da asarar matsin lamba zuwa cikakkiyar ƙarancin ƙima.
Fara saukewa (na waje)
Babu tsohon masana'anta mai saukewa na farko na ciki. A madadin, ana iya shigar da mai saukar da farawa a cikin shuka.
Aiki:
Lokacin da aka fara compressor, bawul ɗin solenoid yana karɓar wuta ta hanyar sauya lokaci kuma yana buɗe hanyar wucewa tsakanin layin fitarwa da tsotsa. A lokaci guda, bawul ɗin da ba zai dawo ba a cikin layin fitarwa yana rufewa kuma yana hana sake dawowa na refrigerant daga na'urar (Fig. 5). Compressor yanzu gajere ne kuma yana isar da shi daga fitowar kai tsaye cikin abin sha. Bambancin matsin lamba saboda haka yana raguwa sosai. A sakamakon haka, da karfin juyi a kan tuƙi shaft na kwampreso ya ragu sosai. Motar tuƙi na iya farawa yanzu tare da ƙaramin matakin farawa. Da zaran motar da kwampreta suka kai ga ƙimar ƙimar su, bawul ɗin solenoid ya rufe kuma bawul ɗin da ba zai dawo ba ya buɗe (Fig. 6). Compressor yanzu yana aiki ƙarƙashin nauyin al'ada.
Muhimmi:
- Za a iya amfani da mai saukewa na farawa kawai a lokacin farawa.
- Bincika bawul ɗin solenoid da bawul ɗin mara dawowa akai-akai don matsewa.
- Bugu da ƙari, muna ba da shawarar yin amfani da ma'aunin zafi da sanyio a gefen fitarwa na damfara. Wannan yana kare kwampreso daga zazzagewar zafi. Haɗa ma'aunin zafi da sanyio a jeri akan sarkar aminci na da'irar sarrafawa, don kashe kwampreso idan ya cancanta.
- Bi waɗannan umarnin don guje wa wuce gona da iri.
Kwanciya tsotsa da layukan matsa lamba
- Bututun da ba a shigar da shi ba daidai ba zai iya haifar da tsagewa da hawaye, sakamakon shine asarar firiji.
- Daidaitaccen shimfidar layukan tsotsa da fitarwa kai tsaye bayan damfara suna da alaƙa da tsarin tafiyar da motsin motsi da santsi.
Ka'idar babban yatsan hannu: Koyaushe sanya sashin bututu na farko yana farawa daga bawul ɗin kashewa zuwa ƙasa kuma daidai da mashin tuƙi.
Yin aiki da bawuloli masu kashewa
- Kafin buɗe ko rufe bawul ɗin rufewa, saki hatimin sandal ɗin bawul ta kusan. 1/4 na juyi counter-clockwise.
- Bayan kunna bawul ɗin kashe-kashe, sake matse hatimin sandal ɗin bawul ɗin daidaitacce a gefen agogo.
Yanayin aiki na haɗin sabis masu kullewa
Buɗe bawul ɗin kashewa:
Spindle:
juya zuwa hagu (counter-clockwise) gwargwadon yadda zai tafi. -> Bawul ɗin rufewa gaba ɗaya buɗe / haɗin sabis ya rufe.
Buɗe haɗin sabis
Spindle: Juya 1/2 - 1 agogon agogo.
- An buɗe bawul ɗin rufewa / kashe haɗin sabis.
Bayan kunna sandar, gabaɗaya ta sake dacewa da hular kariyar sandar kuma ƙara 14-16 Nm (10-12 lb-ft). Wannan yana aiki azaman fasalin hatimi na biyu yayin aiki.
Tace bututun tsotsa da bushewar tacewa
Don tsarin da dogayen bututu da mafi girman matakin gurɓatawa, ana ba da shawarar tacewa a gefen tsotsa. Dole ne a sabunta matatun ya danganta da girman gurɓataccen abu (rage asarar matsa lamba). Danshi a cikin da'irar firiji na iya haifar da samuwar crystal da hydrate. Saboda wannan dalili, muna ba da shawarar yin amfani da na'urar bushewa da gilashin gani tare da alamar danshi.
Haɗin lantarki
Gabaɗaya aminci
- Hadarin girgiza wutar lantarki! Babban voltage!
- Yi aiki kawai lokacin da tsarin lantarki ya katse daga wutar lantarki!
- Lokacin haɗa na'urorin haɗi tare da kebul na lantarki, mafi ƙarancin lanƙwasa radius na 3 x diamita na USB dole ne a kiyaye don shimfiɗa kebul ɗin.
Haɗa injin kwampreta daidai da zanen kewayawa (duba cikin akwatin tasha).
- Yi amfani da madaidaicin wurin shigar da kebul na nau'in kariyar daidai (duba farantin suna) don jigilar igiyoyi cikin akwatin tasha. Saka iri yana sauƙaƙawa kuma hana alamun chafe akan igiyoyi.
- Kwatanta voltage da ƙimar mitar tare da bayanai don wadatar wutar lantarki.
- Haɗa motar kawai idan waɗannan dabi'u iri ɗaya ne.
Bayani don lambar sadarwa da zaɓin lamba na mota
Duk na'urorin kariya da sauyawa ko sassan sa ido dole ne a sanya su daidai da ƙa'idodin aminci na gida da ƙayyadaddun ƙayyadaddun bayanai (misali OSHA, UL/CSA) gami da bayanan masana'antar. Ana buƙatar maɓallan kariyar mota! Dole ne a ƙididdige masu tuntuɓar ababen hawa, layin ciyarwa, fis da maɓallan kariyar mota bisa madaidaicin aiki na yanzu (duba farantin suna). Don kariyar mota yi amfani da na'urar kariyar abin da ta dogara da halin yanzu da jinkirin ɗaukar nauyi don sarrafa duk matakai uku. Saita na'urar kariya ta wuce gona da iri ta yadda dole ne a kunna ta a cikin sa'o'i 2, idan akwai max sau 1.2. aiki halin yanzu.
Madaidaicin mota, ƙira don farawa kai tsaye ko ɓangarori
Compressors tare da wannan alamar sun dace da farawa kai tsaye ko wani ɓangare. An kasu da juzu'in motar zuwa kashi biyu:
- Sashe na iska 1 = 50% da juzu'i 2 = 50%.
- Wannan rabe-raben iskar gas yana rage lokacin farawa da ake buƙata don farkon juzu'i zuwa kusan. 50% na wannan don farawa kai tsaye.
Ba a buƙatar farawa da zazzage kayan inji tare da bawul ɗin solenoid na kewayawa.
An haɗa motar don farawa kai tsaye (YY) a masana'anta. Don farawa Y/YY na juzu'i dole ne a cire gadoji kuma an haɗa layin ciyarwar mota bisa ga zanen kewayawa:
SANARWA
Rashin yin wannan yana haifar da adawa da filayen juyawa kuma yana haifar da lalacewa ga motar. Bayan motar ta tashi ta hanyar juzu'in juzu'i na 1, juzu'i na 2 dole ne a kunna bayan matsakaicin jinkiri na daƙiƙa ɗaya. Rashin yin biyayya zai iya yin illa ga rayuwar sabis ɗin motar.
Asalin zanen kewayawa don juzu'in juzu'i farawa tare da madaidaicin mota
| BP2 | Babban matsa lamba aminci duba |
| BP3 | Safety sarkar (high/motsi saka idanu) |
| BT1 | Cold conductor (PTC firikwensin) iska |
| BT2 | Thermal kariya ma'aunin zafi da sanyio (PTC firikwensin) |
| BT3 | Na'urar zafin mai |
| BT4 | Canjin fitarwa (thermostat) |
| DELTA-P II | Babban firikwensin matsin lamba na mai DELTA-P II (na'ura) |
| Farashin EB1 | Mai dumama dumama |
| Saukewa: EC1 | Injin Compressor |
| FC1.1/1.2 | Motar kariya ta sauya |
| FC2 | Sarrafa fis ɗin kewaya wutar lantarki |
| INT69 G | Naúrar faɗakarwa Electronic INT69 G |
| KF1 | Jinkirta gudun ba da sanda don tuntuɓar mai sauyawa |
| QA1 | Babban canji |
| QA2 | Mais contactor (bangaren iska 1) |
| QA3 | Mais contactor (bangaren iska 2) |
| SF1 | Sarrafa voltage canza |
Mota ta musamman: ƙira don farawa kai tsaye ko tauraro-delta
Ana buƙatar farawa da zazzage injin inji tare da bawul ɗin solenoid na kewaye don farawa tauraro-delta.
Farawar tauraro-delta yana yiwuwa ne kawai don samar da wutar lantarki ∆ (230V).
Exampda:
- A cikin masana'anta an haɗa motar don farawa kai tsaye daga babban voltage.
- Za a cire amaren don star delta farawa daga low voltage.
Mahimmin zane na kewaye don tauraron-delta farawa 230V ∆ / 400 VY
| BP2 | Babban matsa lamba aminci duba |
| BP3 | Safety sarkar (high/motsi saka idanu) |
| BT1 | Cold conductor (PTC firikwensin) iska |
| BT2 | Thermal kariya ma'aunin zafi da sanyio (PTC firikwensin) |
| BT3 | Na'urar zafin mai |
| BT4 | Canjin fitarwa (thermostat) |
| DELTA PII | Babban firikwensin matsin lamba na mai DELTA-P II (na'ura) |
| Farashin EB1 | Mai dumama dumama |
| Saukewa: EC1 | Injin Compressor |
| FC1.1/1.2 | Motar kariya ta sauya |
| FC2 | Sarrafa fis ɗin kewaya wutar lantarki |
| INT69 G | Naúrar faɗakarwa Electronic INT69 G |
| KF1 | Jinkirta gudun ba da sanda don tuntuɓar mai sauyawa |
| QA1 | Babban canji |
| QA2 | Mais lamba |
| QA3 | Δ-lantarki |
| QA4 | Y-lantarki |
| SF1 | Sarrafa voltage canza |
Naúrar faɗakarwa Electronic INT69 G
Motar ta kwampreso tana sanye da na'urori masu auna zafin jiki na sanyi (PTC) da aka haɗa zuwa naúrar faɗakarwa ta lantarki INT69 G a cikin akwatin tasha. Idan akwai matsanancin zafin jiki a cikin iskar motar, INT69 G yana kashe mai tuntuɓar motar. Da zarar an sanyaya, za a iya sake kunna shi kawai idan kulle lantarki na relay na fitarwa (tashoshi B1+B2) an sake shi ta hanyar katse wutar lantarki.tage. Hakanan za'a iya kiyaye gefen gas mai zafi na compressor daga zafin jiki ta amfani da ma'aunin zafi da sanyio (na'urorin haɗi).
Naúrar tana yin tafiye-tafiye lokacin da abin hawa ko yanayin aiki mara izini ya auku. Nemo ku gyara sanadin.
- Ana aiwatar da fitarwa na sauyawar gudun ba da sanda azaman lambar sadarwa mai sauyawa. Wannan da'irar lantarki tana aiki bisa ga ƙa'idar halin yanzu, watau gudun ba da sanda ya faɗo zuwa wurin da ba shi da aiki kuma yana kashe mai tuntuɓar motar koda kuwa an sami hutun firikwensin ko buɗe kewaye.
Haɗin naúrar faɗakarwa INT69 G
Haɗa naúrar faɗakarwa INT69 G daidai da dia-gram. Kare naúrar faɗakarwa tare da jinkirin fuse (FC2) na max. 4 A. Domin tabbatar da aikin kariyar, shigar da naúrar faɗakarwa a matsayin kashi na farko a cikin da'irar wutar lantarki.
Dole ne a auna kewaye BT1 da BT2 (PTC firikwensin) kada su haɗu da vol na wajetage. Wannan zai lalata sashin jawo INT69 G da na'urori masu auna firikwensin PTC.
Gwajin aikin naúrar jawo INT69 G
Kafin ƙaddamarwa, bayan gyara matsala ko yin canje-canje ga da'irar wutar lantarki, duba aikin naúrar faɗakarwa. Yi wannan rajistan ta amfani da mai gwada ci gaba ko gage.
| Gage jihar | Relay matsayi |
| Yanayin kashewa | 11-12 |
| Saukewa: INT69G | 11-14 |
| Cire haɗin PTC | 11-12 |
| Saka mai haɗin PTC | 11-12 |
| Sake saitin bayan an kunna mains | 11-14 |
Matsayin Relay INT69 G
Na'urar dumama mai (kayan aiki)
Lokacin da kwampreso ya tsaya cik, firiji yana bazuwa cikin man mai na gidajen compressors, ya danganta da matsa lamba da zafin yanayi. Wannan yana rage karfin man mai. Lokacin da compressor ya fara tashi, firijin da ke cikin mai yana ƙafewa ta hanyar raguwar matsa lamba. Sakamakon zai iya zama kumfa da ƙaura na mai, yana haifar da girgiza mai a wasu yanayi.
Aiki:
Na'urar dumama mai tana aiki lokacin da kwampreta ya tsaya cik. Lokacin da compres-sor ya fara tashi, injin dumama mai yana sake kashewa ta atomatik.
Haɗin kai:
Dole ne a haɗa mahaɗar dumbin mai ta hanyar haɗin gwiwa (ko lambar sadarwa ta layi ɗaya) na mai tuntuɓar kwampreso zuwa wani keɓaɓɓen da'irar lantarki.
- El. bayanai: 115 V AC 60 Hz, 160 W.
Haɗin kai zuwa hanyar yanzu na sarkar kulawar aminci ba a ba da izini ba.
Mai sarrafa ƙarfi (na'urorin haɗi)
Fuus (max. 3xlB daidai da IEC 60127-2-1) daidai da ƙimar halin yanzu dole ne a sanya shi a gaban kowane murɗaɗɗen maganadisu na mai sarrafa ƙarfin aiki azaman kariyar gajeriyar kewayawa. Ra-ted voltage na fuse dole ne ya zama daidai ko girma fiye da ƙididdigan voltage na Magnetic coil. Ƙarfin fis ɗin don kashewa dole ne ya zama mafi girma ko daidai da matsakaicin matsakaicin da aka zayyana na gajeren zango a wurin shigarwa.
Zaɓi da aiki na compressors tare da masu juyawa mita
Don amintaccen aiki na kwampreso, mai sauya mitar dole ne ya sami damar yin amfani da nauyi na aƙalla 140% na matsakaicin halin yanzu na compressor (I-max.) na aƙalla daƙiƙa 3.
Lokacin amfani da masu sauya mitar, dole ne kuma a lura da abubuwa masu zuwa:
- Matsakaicin halattaccen aiki na yanzu na kwampreso (I-max) (duba nau'in farantin karfe ko bayanan fasaha) dole ne a ƙetare shi.
- Idan girgizar da ba ta dace ba ta faru a cikin tsarin, mitar mitar da abin ya shafa a cikin mai sauya mitar dole ne a cire ta yadda ya kamata.
- Matsakaicin abin da ake fitarwa na mai sauya mitar dole ne ya zama mafi girma fiye da matsakaicin halin yanzu na compressor (I-max).
- Yi duk ƙirƙira da shigarwa daidai da ƙa'idodin aminci na gida da ƙa'idodi gama gari (misali VDE) da ƙa'idodi da kuma daidai da ƙayyadaddun ƙira na masana'anta mai sauya mitar.
| Gudun juyawa iyaka | 0 - f min | f-min - f-max |
| Farawa lokaci | <1 s | ca. 4s ku |
| Kashe-kashe lokaci | nan da nan | |
f-min/f-max duba babi na 9: Bayanan fasaha: halattaccen kewayon mitar
Gudanarwa
Shirye-shiryen farawa
Don kare kwampreso daga yanayin aiki mara izini, matsa lamba mai ƙarfi da ƙananan latsawa dole ne a gefen shigarwa.
Compressor ya yi gwaji a masana'anta kuma an gwada dukkan ayyuka. Don haka babu umarnin shiga na musamman.
Duba compressor don lalacewar sufuri!
Gwajin ingancin matsi
An gwada compressor a cikin masana'anta don amincin matsi. Idan duk da haka za a yi gwajin ingancin matsi, wannan ya kamata a yi shi daidai da UL 207 ko daidaitaccen ma'aunin aminci ba tare da haɗa da kwampreso ba.
Gwajin zubewa
HADARI
Hadarin fashewa!
Dole ne kawai a matsi da kwampreso ta amfani da nitrogen (N2). Kada a taɓa matsawa da iskar oxygen ko wasu iskar gas! Matsakaicin izinin wuce gona da iri na compressor ba dole ba ne a wuce shi a kowane lokaci yayin aikin gwaji (duba bayanan farantin suna)! Kada a haxa duk wani abin sanyi da nitrogen saboda wannan zai iya haifar da iyakar ƙonewa zuwa kewayo mai mahimmanci.
- Aiwatar da gwajin ɗigogi akan injin firiji daidai da UL 207 ko daidaitaccen ma'aunin aminci, yayin da koyaushe yana lura da matsakaicin izinin wuce gona da iri na kwampreso.
Ficewa
- Kada a fara kwampreso idan yana ƙarƙashin injin. Kar a yi amfani da kowane voltage – har ma don dalilai na gwaji (dole ne a yi aiki da shi tare da firji kawai).
- Ƙarƙashin vacuum, ɓangarorin walƙiya da tazara a halin yanzu na ƙusoshin haɗin jirgi na tasha suna gajarta; wannan na iya haifar da iska da lalacewa ta tashar jirgin ruwa.
- Da farko fitar da tsarin sannan kuma haɗa da kwampreso a cikin aikin ƙaura.
- Sauke matsa lamba na kwampreso.
- Bude igiyar tsotsa da matsi na kashe bawuloli.
- Fitar da tsotsa da ɓangarorin matsewa ta amfani da famfo.
- A ƙarshen aikin ƙaura, injin ya kamata ya zama <1.5 mbara (0.02 psia) lokacin da aka kashe famfo.
- Maimaita wannan tsari sau da yawa kamar yadda ake buƙata.
Cajin firiji
HANKALI
Saka kayan kariya na sirri kamar tabarau da safar hannu masu kariya!
- Tabbatar cewa tsotsawa da layin rufewa a buɗe suke.
- Tare da na'urar damfara a kashe, ƙara refrigeren ruwa kai tsaye zuwa na'ura ko mai karɓa, karya injin.
- Idan refrigerant yana buƙatar toshe sama bayan ya fara kwampreso, ana iya sanya shi cikin sigar tururi a gefen tsotsa, ko kuma, ɗaukar matakan da suka dace, shima a cikin sigar ruwa a mashigar zuwa mashin.
SANARWA
- Guji cika tsarin tare da firiji!
- Don guje wa sauye-sauye a cikin maida hankali, gaurayawan refrigerant na zeotropic dole ne kawai a cika su a cikin injin sanyaya a cikin ruwa.
- Kada a zuba ruwa mai sanyaya ta cikin bawul ɗin layin tsotsa akan kwampreso.
- Ba ya halatta a haxa abubuwan da ake ƙarawa da mai da firji.
Farawa
GARGADI
Tabbatar cewa duka bawul ɗin rufewa suna buɗe kafin fara kwampreso!
- Bincika cewa aminci da na'urorin kariya (matsi, kariyar mota, matakan kariyar lambar sadarwa, da sauransu) duk suna aiki da kyau.
- Kunna compressor kuma ba da damar yin aiki na akalla mintuna 10.
- Duba matakin mai ta: Dole ne mai ya kasance a bayyane a cikin gilashin gani.
Idan ya zama dole a kara yawan mai, akwai haɗarin tasirin guduma mai.
Idan haka ne a duba dawo da mai!
Gujewa slugging
- Slugging na iya lalata kwampreta kuma ya sa firiji ya zube.
Don hana slugging:
- Dole ne a tsara cikakken tsarin firiji yadda ya kamata.
- Dole ne a ƙididdige duk abubuwan da aka haɗa tare da juna dangane da fitarwa (musamman magudanar ruwa da bawul ɗin faɗaɗawa).
- Suction gas superheat a shigar da kwampreso ya zama min. 7 - 10 K. (duba saitin bawul ɗin haɓakawa).
- Dole ne tsarin ya kai matsayin daidaito.
- Musamman ma a cikin tsarin mahimmanci (misali maki da yawa na evaporator), ana ba da shawarar matakan kamar maye gurbin tarkon ruwa, bawul ɗin solenoid a cikin layin ruwa, da sauransu.
- Kada a sami motsi na sanyaya komai yayin da compressor ke tsaye.
Kulawa
Shiri
Kafin fara kowane aiki akan compressor:
- Kashe compressor kuma ka tsare shi don hana sake farawa.
- Rage kwampreso na tsarin matsin lamba.
- Hana iska daga kutsawa cikin tsarin!
Bayan an yi gyara:
- Haɗa maɓallin aminci.
- Fitar da kwampreso.
- Saki makullin sauyawa.
Aikin da za a yi
Don ba da garantin ingantaccen aiki da rayuwar sabis na kwampreso, muna ba da shawarar aiwatar da aikin sabis da dubawa a tazara na yau da kullun:
Canjin mai:
- ba dole ba ne ga tsarin da masana'anta ke samarwa.
- don shigarwar filin ko lokacin aiki kusa da iyakar aikace-aikacen: a karon farko bayan sa'o'in aiki 100 zuwa 200, sannan kusan. kowace shekara 3 ko 10,000 - 12,000 hours aiki. Zubar da man da aka yi amfani da shi bisa ka'ida; kiyaye dokokin kasa.
Binciken shekara-shekara:
Matsayin mai, matsananciyar zubewa, hayaniya mai gudana, matsa lamba, yanayin zafi, aikin na'urori masu taimako kamar na'urar dumama mai, matsa lamba.
Shawarwari / kayan haɗi na kayan gyara
Ana iya samun kayan gyara da na'urorin haɗi akan kayan aikin zaɓin kwampreso a ƙarƙashin vap.bock.de da kuma a bockshop.bock.de.
Yi amfani da kayan gyara na Bock na gaske!
Man shafawa / mai
Nau'in man da aka cika a matsayin ma'auni a cikin masana'anta an yi masa alama akan farantin suna, kuma wannan yakamata a yi amfani da shi koyaushe, koda kuwa a cikin sassan kulawa. Madadin nau'ikan mai na iya bambanta sosai cikin inganci saboda abubuwan da ake ƙarawa ko ƙarancin albarkatun ƙasa ta masana'anta. Tabbatarwa a cikin kwampreso duk iyakokin aiki ba za a iya lamunce ba, idan ana amfani da irin waɗannan nau'ikan mai. A saboda wannan dalili ne kawai muke ba da shawarar amfani da mai daga Bock! Bock ba shi da alhakin duk wani lahani da ya taso daga madadin nau'in mai.
- Bock misali mai irin: BOCK lub E55
Saukewa
Rufe bawul ɗin kashewa akan kwampreso. Cire na'urar sanyaya (dole ne a fitar da shi cikin muhalli) kuma a jefar da shi bisa ga ƙa'idodi. Lokacin da kwampreso ya ɓaci, gyara skru masu ɗaure na bawul ɗin kashewa. Cire compressor ta amfani da hawan da ya dace. Zubar da mai a ciki daidai da dokokin kasa da suka dace.
Na'urorin haɗi
Mai sarrafa iya aiki
HANKALI
Idan an shigar da mai sarrafa ƙarfin aiki a masana'anta, ana shigar da bangaren sarrafawa (bawul ɗin matukin jirgi) kuma abokin ciniki ya haɗa shi.
Kafin farawa, cire murfin a ma'aunin ƙarfin aiki kuma musanya shi tare da rukunin kulawa da ke kewaye (bawul ɗin matukin jirgi). Hankali! Compressor yana cikin matsin lamba! Sanya kwampreso da farko. Dunƙule a cikin naúrar sarrafawa (bawul ɗin matukin jirgi) tare da zoben hatimi kuma m tare da 15 Nm. Rigar zaren gefe tare da man ester. Saka na'urar maganadisu, ɗaure shi da knurled nut kuma haɗa shi.
GARGADI:
Yawancin masu kula da iya aiki ba za su iya canzawa a lokaci guda yayin aikin kwampreso ba! In ba haka ba kwatsam canjin kaya na iya lalata kwampreso! Yi aiki tare da tazarar sauyawa na 60s.
Bi tsarin sauyawa:
- Canja wurin LR1 60s LR2
- Ana kashe LR2 60s LR1
SANARWA
- Ayyukan da aka tsara ƙarfin aiki yana canza saurin iskar gas da ƙimar matsa lamba na injin refrigerating: Daidaita layin layin tsotsa da ƙima daidai da haka, kar a saita tazarar sarrafawa kusa kuma kar a bar tsarin ya canza fiye da sau 12 a cikin awa ɗaya ( injin firiji dole ne. sun kai matsayin daidaito). Ci gaba da aiki a cikin sarrafawa stage ba a ba da shawarar ba saboda saurin iskar gas a cikin tsarin shuka a ƙarƙashin wasu yanayi baya bada garantin isassun mai dawowa ga kwampreso tare da mai sarrafa ƙarfin aiki. Muna ba da shawarar canzawa zuwa aiki mara tsari (100% iya aiki) na aƙalla mintuna 5 a kowace sa'ar aiki da aka kayyade iya aiki. Hakanan ana iya samun tabbataccen dawowar mai ta hanyar buƙatun iya aiki 100% bayan kowace kwampreso zata sake farawa.
- Kunna wutar lantarki na bawul ɗin solenoid: Kullum buɗewa, (mai daidaitawa zuwa ƙarfin kwampreso 100%.
- Don ƙa'idar ƙarfin dijital duba takaddar 09900.
Na'urorin haɗi na musamman an riga an saka su a masana'anta idan abokin ciniki ya ba da oda na musamman. Sake gyarawa yana yiwuwa cikin cikakken yarda da umarnin aminci da umarnin gyara da ke kewaye da kayan. Ana samun bayanai game da amfani, aiki, kiyayewa da kuma hidimar abubuwan da aka haɗa a cikin wallafe-wallafen da aka buga ko akan intanet a ƙarƙashin vap.bock.de.
Mai raba mai
Slugging mai na iya haifar da lalacewa ga kwampreso.
Don hana slugging mai:
- Dawowar mai daga mai raba mai dole ne a jagorance shi zuwa haɗin da aka yi niyya (D1) akan mahalli na kwampreso.
- Komawar mai kai tsaye cikin layin tsotsa daga mai raba mai bai halatta ba.
- Tabbatar cewa mai raba mai yana da girma sosai.
Mai kula da matakin mai
Tsarukan daidaita matakin mai sun tabbatar da kansu tare da da'irori iri ɗaya na compressors da yawa. Ana ba da haɗin "0" don shigar da mai daidaita matakin mai (duba zane mai girma). Duk masu kula da matakin man inji na yau da kullun daga AC & R, ESK, Carly da tsarin ka'idojin matakin mai na lantarki daga AC & R, Teklab, OM3 TraxOil daga Alco da ESK (siffa mai tsayi kawai) ana iya haɗa kai tsaye ba tare da adaftan ba (duba siffa 21). Ba a buƙatar gilashin gani akan mai daidaita matakin mai.
An yi taron a matsayin asali na daidaitaccen gilashin gani (duba hoto 22).
Bayanan fasaha
|
Nau'in UL-HGX66e/ |
No na silinda |
Kaura (1450 rpm / 1740 rpm) |
Lantarki data 3 |
Nauyi |
Haɗin kai 4 | Mai caji
(misali aiki) |
Mai caji (gani gilashin tsakiya) |
||||||
|
1 |
2 |
2 |
farawa halin yanzu (rotor kulle) |
halatta mita mita |
Zazzagewa layi DV |
tsotsa layi SV | |||||||
| 50 Hz
60 Hz |
PW 1+2 | PW 1/PW 1+2 | |||||||||||
| V | A | kW (HP) | A | Hz | lb | mm
(inch) |
mm
(inch) |
ltr (fl.oz) | ltr (fl.oz) | ||||
| cfh | |||||||||||||
| 1340 ml 31 |
6 |
4115
4938 |
380-420 VY/YY - 3 - 50 Hz PW
440-480 VY/YY - 3 - 60 Hz PW PW = Sashe na iska, rabon iska: 50%/50% |
54 | 31,9 (43,4) | 170/275 |
25-60 |
671 |
42 (1 5/8) |
54 (2/1) |
4.4 (155) |
3.8 (134) |
|
| 1340 S37 | 4115
4938 |
65 | 38,1 (51,8) | 196/335 | 678 | ||||||||
| 1540 ml 36 | 4724
5668 |
62 | 37,2 (50,6) | 170/275 | 666 | ||||||||
| 1540 S42 | 4724
5668 |
75 | 44,4 (60,4) | 196/335 | 673 | ||||||||
| 1750 ml 44 | 5374
6449 |
72 | 42,4 (57,6) | 196/335 | 656 | ||||||||
| 1750 S50 | 5374
6449 |
87 | 50,7 (68,9) | 222/361 | 677 | ||||||||
| 2070 ml 50 | 6356
7627 |
85 | 50,7 (68,9) | 196/335 | 680 |
64 (2/5) |
|||||||
| 2070 S60 | 6356
7627 |
103 | 60,7 (82,5) | 222/361 | 691 | ||||||||
- Haƙuri (± 10%) dangane da ma'anar ƙimar voltage zango. Sauran voltages da nau'ikan halin yanzu akan buƙata.
- Bayani dalla-dalla ga max. amfani da wutar lantarki yana amfani da aikin 60Hz
- Yi lissafin max. aiki halin yanzu / max. amfani da wutar lantarki don ƙirar fuses, layin wadata da na'urorin aminci.
Fuse: Kayan amfani AC3
- Yi lissafin max. aiki halin yanzu / max. amfani da wutar lantarki don ƙirar fuses, layin wadata da na'urorin aminci.
- Duk ƙayyadaddun bayanai sun dogara ne akan matsakaita na voltage kewayon
- Don haɗin siyar
Girma da haɗin kai
UL-HGX66e
| SV DV | Layin tsotsa duba bayanan fasaha, babi na 9 Layin fitarwa | |
| A | Haɗin tsotsa gefen, ba a kulle ba | 1/8 "NPTF |
| A1 | Haɗin tsotsa gefen, mai kullewa | 7/16" UNF |
| B | Gefen fitarwa na haɗi, ba a kulle ba | 1/8 "NPTF |
| B1 | Gefen fitarwa na haɗi, mai kullewa | 7/16" UNF |
| C | Connection mai matsa lamba aminci canza OIL | 1/8 "NPTF |
| D | Connection mai matsa lamba aminci canza LP | 7/16" UNF |
| D1 | Connection mai dawowa daga mai raba mai | 1/4 "NPTF |
| F | Magudanar mai | M12x1.5 |
| H | Toshe cajin mai | 1/4 "NPTF |
| J | Connection man sump hita | 3/8 "NPTF |
| K | Gilashin gani | 3 x m6 |
| L | Haɗin ma'aunin zafi mai zafi | 1/8 "NPTF |
| M | Tace mai | M12x1.5 |
| O | Mai daidaita matakin man fetur | 3 x m6 |
| P | Haɗi mai matsa lamba bambancin firikwensin | M20x1.5 |
| ÖV | Bawul ɗin sabis na mai haɗin haɗi | 1/4 "NPTF |
| Q | Haɗin zafin mai | 1/8 "NPTF |
| W | Haɗin don allurar refrigerant | 2 x 1/8" NPTF |
Sanarwa na haɗawa
Sanarwa na haɗawa don injunan da ba su cika ba daidai da EC Directive Machinery 2006/42/EC, Annex II 1.B
Mai ƙira:
Boka GmbH
Benzstraße 7 72636 Frickenhausen, Jamus.
Mu, a matsayin masana'anta, muna bayyana cikin alhakin kawai cewa injin bai cika ba
Suna:
Nau'u:
Semi-hermetic kwampreso
- HG(X)12P/60-4 S (HC) ………………………… HG(X)88e/3235-4(S) (HC)
- UL-HGX12P/60 S 0,7……………………………… UL-HGX66e/2070 S 60
- HGX12P/60 S 0,7 LG………………………….. HGX88e/3235 (ML/S) 95 LG
- HG(X)22(P)(e)/125-4 A ………………………… HG(X)34(P)(e)/380-4 (S) A
- HGX34(P)(e)/255-2 (A) ………………………….. HGX34(P)(e)/380-2 (A)(K)
- HA(X)12P/60-4 ……………………………… HA(X)6/1410-4
- HAX22e/125 LT 2 LG …………………………. HAX44e/665 LT 14 LG
- HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
- UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
- HGX12/20-4 (ML/S/SH) CO2T………………. HGX46/440-4 (ML/S/SH) CO2 T
- UL-HGX12/20 ML(P) 2 CO2T………………. UL-HGX46/440 ML(P) 53 CO2T
- HGZ(X)7/1620-4 ……………………………. HGZ(X)7/2110-4
- HGZ(X)66e/1340 LT 22……………………………… HGZ(X)66e/2070 LT 35
- HRX40-2 CO2 TH………………………………. HRX60-2 CO2 TH
- Suna: Buɗe nau'in kwampreso
- Nau'u:
- F(X)2 …………………………………………………… F(X)88/3235 (NH3)
- FK(X)1………………………………………………. FK(X)3
- FK(X)20/120 (K/N/TK)………………………. FK(X)50/980 (K/N/TK)
ya bi waɗannan tanade-tanade na umarnin da aka ambata a sama:
A cewar Annex I, maki 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.3, 1.3.7, 1.5.1, 1.5.2, 1.5.13 da 1.7.1 zuwa 1.7.4 ( banda 1.7.4 f) sun cika.
Aiwatar da ƙa'idodi masu jituwa, musamman:
- TS EN ISO 12100 Tsaro na injin - Ka'idodin ƙira - Kimanta haɗari da raguwar haɗari
- TS EN 12693 Tsarin firiji da famfo mai zafi - Aminci da buƙatun muhalli - Maɓallin maɓalli mai kyau
Bayani:
- Mun kuma ayyana cewa an ƙirƙiri takaddun fasaha na musamman don wannan injin ɗin da bai cika ba daidai da Annex VII, Sashe na B kuma muna wajabta samar da waɗannan bisa ga buƙatu daga hukumomin ƙasa guda ɗaya ta hanyar canja wurin bayanai.
- An haramta aiwatar da aikin har sai an tabbatar da cewa injin ɗin da za a shigar da na'urar da ba ta cika ba a cikinta ta bi ka'idodin Injin EC da EC Declaration of Conformity, Annex II. 1. Akwai.
Mutumin da aka ba da izini don haɗawa da ba da takaddun fasaha:
Boka GmbH
Alexander Layh Benzstraße 7 72636 Frickenhausen, Jamus.
Frickenhausen, 04 ga Janairu, 2021
Sanarwa na haɗa kayan aikin da aka kammala daidai da Dokokin Bayar da Kayan Aikin Kaya na Burtaniya 2008, Annex II 1.B
Mai ƙira:
Bock GmbH Benzstraße 7 72636 Frickenhausen, Jamus.
Mu, a matsayin masana'anta, mun ayyana cikin alhakin kawai cewa injinan da aka kammala a wani bangare
- Suna:
- Semi-hermetic kwampreso
- Nau'u:
- HG(X)12P/60-4 S (HC) ………………………… HG(X)88e/3235-4(S) (HC)
- UL-HGX12P/60 S 0,7……………………………… UL-HGX66e/2070 S 60
- HGX12P/60 S 0,7 LG………………………….. HGX88e/3235 (ML/S) 95 LG
- HG(X)22(P)(e)/125-4 A ………………………… HG(X)34(P)(e)/380-4 (S) A
- HGX34(P)(e)/255-2 (A) ………………………….. HGX34(P)(e)/380-2 (A)(K)
- HA(X)22e/125-4 …………………………….. HA(X)6/1410-4
- HAX22e/125 LT 2 LG …………………………. HAX44e/665 LT 14 LG
- HGX12e/20-4 (ML/S) CO2 (LT) ……….. HGX44e/565-4 S CO2
- UL-HGX12e/20 (S/ML) 0,7 CO2 (LT)… UL-HGX44e/565 S 31 CO2
- HGX12/20-4 (ML/S/SH) CO2T………………. HGX46/440-4 (ML/S/SH) CO2 T
- UL-HGX12/20 ML(P) 2 CO2T……………………… UL-HGX46/440 ML(P) 53 CO2T
- HGZ(X)7/1620-4 ……………………………. HGZ(X)7/2110-4
- HGZ(X)66e/1340 LT 22……………………………… HGZ(X)66e/2070 LT 35
- HRX40-2 CO2 TH……………………………….. HR (Z) X60-2 CO2 T (H) (V)
- Suna: Buɗe nau'in kwampreso
- Nau'u:
- F(X)2 …………………………………………………………… F(X)88/3235 (NH3)
- FK(X)1………………………………………………………………. FK(X)3
- FK(X)20/120 (K/N/TK)……………………………….. FK(X)50/980 (K/N/TK)
- Serial lambar: BC00000A001 - BN99999Z999
ya bi waɗannan tanade-tanade na kayan aikin Dokokin da aka ambata a sama:
- Dangane da Jadawalin 2, sashi na 1, maki 1.1.2, 1.1.3, 1.1.5, 1.3.2, 1.3.3, 1.3.7, 1.5.1, 1.5.2, 1.5.13 da 1.7.1 zuwa 1.7.4. 1.7.4 (sai dai XNUMX f) sun cika.
Matsayin da aka tsara:
- TS EN ISO 12100 Tsaro na injin - Ka'idodin ƙira - Kimanta haɗari da raguwar haɗari
- TS EN 12693 Tsarin firiji da famfo mai zafi - Aminci da buƙatun muhalli - Maɓallin maɓalli mai kyau
Bayani:
- Mun kuma ayyana cewa an ƙirƙiri takaddun fasaha na musamman na wannan injin da aka kammala daidai da Annex II, 1. B kuma muna wajabta samar da waɗannan bisa ga buƙatu daga hukumomin ƙasa guda ɗaya ta hanyar canja wurin bayanai.
- An haramta yin aiki har sai an tabbatar da cewa injin da za a shigar da na'urar da aka kammala a cikinta ta bi ka'idodin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kayayyakin Kaya na Burtaniya 2008 da EC Declaration of Conformity, Annex II, 1. Akwai.
Mutumin da aka ba da izini don haɗawa da ba da takaddun fasaha:
Boka GmbH
Alexander Layh Benzstraße 7 72636 Frickenhausen, Jamus.
Frickenhausen, 14 ga Oktoba, 2022
UL-Takaddar Yardawa
Ya ku abokin ciniki,
Ana iya saukar da Takaddar Yarda da Takaddar QR-Code mai zuwa:
https://vap.bock.de/stationaryapplication/Data/DocumentationFiles/UL-Certificateofconformity.pdf
Danfoss A / S
Maganin Yanayi • danfoss.us • +1 888 326 3677 • heat.cs.na@danfoss.com.
Duk wani bayani, gami da, amma ba'a iyakance ga bayani kan zaɓin samfur, aikace-aikacen sa ko amfani da shi ba, ƙirar samfur, nauyi, girma, iyawa ko duk wani bayanan fasaha a cikin kwatancen kasida, tallace-tallace, da sauransu kuma ko an samar da shi a rubuce, da baki, ta hanyar lantarki, kan layi ko ta hanyar zazzagewa, za a yi la'akari da bayanai, kuma yana ɗaure ne kawai idan kuma har zuwa iyakar, an yi ƙayyadadden bayani a cikin zance ko tabbatarwa. Danfoss ba zai iya karɓar kowane alhakin yuwuwar kurakurai a cikin kasida, ƙasidu, bidiyo da sauran abubuwa ba. Danfoss yana da haƙƙin canza kayan sa ba tare da sanarwa ba. Wannan kuma ya shafi samfuran da aka ba da oda amma ba a isar da su ba muddin ana iya yin irin waɗannan sauye-sauye ba tare da canje-canje don ƙira, dacewa ko aikin samfurin ba.
Duk alamun kasuwanci a cikin wannan kayan mallakar Danfoss A/S ne ko kamfanonin rukunin Danfoss. Danfoss da tambarin Danfoss alamun kasuwanci ne na Danfoss A/S. An kiyaye duk haƙƙoƙi.
© Danfoss | Maganin Yanayi | 2023.07.
Takardu / Albarkatu
 |
Danfoss UL-HGX66e Mai Rarraba Compressor [pdf] Jagoran Shigarwa UL-HGX66e Compressor Maimaitawa, UL-HGX66e |
