G01/G02
მომხმარებლის სახელმძღვანელო
Chapter1. Overview
1.1. სპეციფიკაცია
IIoT კარიბჭე
მახასიათებლები
- Supports OPC UA
- Supports MQTT
- Supports MODBUS TCP/IP Gateway
- Compact Design and DIN-rail Mountable
- Fan-less Cooling System
- Built-in 256 MB Flash Memory
- Supports MPI 187.5K
- Built-in Power Isolator
- cMT-G02 supports WiFi
| მოდელი | cMT-G01 | cMT-G02 | |
| მეხსიერება | ფლეში | 256 მბ | |
| ოპერატიული მეხსიერება | 256 მბ | ||
| პროცესორი | 32 bits RISC Cortex-A8 600MHz | ||
| I/O პორტი | SD ბარათის სლოტი | N/A | |
| USB ჰოსტი | N/A | ||
| USB კლიენტი | N/A | ||
| Ethernet | 10/100/1000 Base-T x 1 | WiFi IEEE 802.11 b / g / n | |
| 10/100 Base-T x 1 | 10/100 Base-T x 1 | ||
| COM პორტი | COM1: RS-232 2W, COM2: RS-485 2W/4W, COM3: RS-485 2W | ||
| RS-485 Built-in Isolation | N/A | ||
| CAN ავტობუსი | N/A | ||
| HDMI | N/A | ||
| აუდიო გამომავალი | N/A | ||
| ვიდეო შეყვანა | N/A | ||
| RTC | ჩაშენებული | ||
| ძალაუფლება | შეყვანის სიმძლავრე | 24±20%VDC | 10.5~28VDC |
| დენის იზოლაცია | ჩაშენებული | ||
| ენერგიის მოხმარება | 230 mA@24VDC | 230mA@12VDC; 115 mA@24VDC | |
| ტtagე წინააღმდეგობა | 500VAC (1 min.) | ||
| იზოლაციის წინააღმდეგობა | Exceed 50M at 500VDC | ||
| ვიბრაციისადმი გამძლეობა | 10-დან 25 ჰერცამდე (X, Y, Z მიმართულება 2G 30 წუთი) | ||
| სპეციფიკაცია | PCB საფარი | დიახ | |
| დანართი | პლასტიკური | ||
| ზომები WxHxD | 109 x 81 x 27 მმ | ||
| წონა | დაახლ. 0.14 კგ | ||
| მთა | 35 მმ DIN რელსის სამონტაჟო | ||
| გარემო | დაცვის სტრუქტურა | IP20 | |
| შენახვის ტემპერატურა | -20° ~ 60°C (-4° ~ 140°F) | ||
| ოპერაციული ტემპერატურა | 0° ~ 50°C (32° ~ 122°F) | ||
| ფარდობითი ტენიანობა | 10% ~ 90% (არაკონდენსირებადი) | ||
| სერთიფიკატი | CE | CE მარკირება | |
| UL | cULus ჩამოთვლილი | Application in progress | |
| პროგრამული უზრუნველყოფა | EasyBuilder Pro ვერსია 5.06.01 | EasyBuilder Pro ვერსია 6.00.01 | |
1.2. ზომები
cMT-G01
წინა View მხარე View
ზედა View ქვედა View
| a | LAN 2 Port (10M/100M) |
| b | LAN 1 Port (10M/100M/1G) |
| c | COM1: RS-232 2W COM2: RS-485 2W/4W COM3: RS-485 2W |
| d | დენის კონექტორი |
| e | ნაგულისხმევი ღილაკი |
cMT-G02
წინა View მხარე View
ზედა View ქვედა View ანტენა
| a | WiFi |
| b | LAN 1 Port (10M/100M) |
| c | COM1: RS-232 2W COM2: RS-485 2W/4W COM3: RS-485 2W |
| d | დენის კონექტორი |
| e | ნაგულისხმევი ღილაკი |
1.3. Connector pin designations
COM1 RS-232, COM2 RS-485 2W/4W, COM3 RS-485 2W 9 Pin, Male, D-sub
| PIN# | COM1 RS-232 | COM2 RS-485 | COM3 RS-485 | |
| 2W | 4W | |||
| 1 | მონაცემთა+ | |||
| 2 | RxD | |||
| 3 | TxD | |||
| 4 | მონაცემები- | |||
| 5 | GND | |||
| 6 | მონაცემთა+ | RX+ | ||
| 7 | მონაცემები- | RX- | ||
| 8 | TX+ | |||
| 9 | TX- | |||
1.4. Restoring factory default
Press and hold on the Default button on the unit for more than 15 seconds to restore factory default.
The IP setting will be restored to default:
cMT-G01:
Ethernet 1: DHCP
Ethernet 2: 192.168.100.1
cMT-G02
WiFi: DHCP
Ethernet: DHCP
Please note that the projects and data stored in the unit are all cleared after pressing the Default button.
1.5. LED ინდიკატორი
LED indicators show the status of IIoT Gateway.
cMT-G01
| ხატულა | ფერი | მნიშვნელობა |
 |
ლურჯი | LAN 1 Communication Status |
 |
ლურჯი | LAN 2 Communication Status |
 |
ნარინჯისფერი | დენის სტატუსი |
 |
მწვანე | Helps the operator to find the cMT-G01. Triggering system register LB-11959 can turn this indicator on/off. Blink LED function in Web/Download interface can also control this indicator. |
cMT-G02
| ხატულა | ფერი | მნიშვნელობა |
|
ლურჯი | LAN Communication Status |
|
ნარინჯისფერი | დენის სტატუსი |
|
მწვანე | Helps the operator to find the cMT-G02. Triggering system register LB-11959 can turn this indicator on/off. Blink LED function in Web/Download interface can also control this indicator. |
შენიშვნა: The second LED indicator from the left is reserved.
1.6. ბატარეა
IIoT Gateway requires a CR1220 lithium battery to keep the RTC running.
1.7. დენის კავშირი
სიმძლავრე: The unit can be powered by DC power only, the voltage range is compatible with most controller DC systems. The power conditioning circuitry inside the unit is accomplished by a switching power supply. The peak starting current can be as high as 500mA.
cMT-G01 voltage range: 24±20% VDC
cMT-G02 voltage დიაპაზონი: 10.5~28 VDC
შენიშვნა: შეაერთეთ დადებითი DC ხაზი "+" ტერმინალთან და DC დამიწება "-" ტერმინალთან.
Chapter2. cMT-G01/G02 System Setting
Connect cMT-G01/G02 via Ethernet cable, and then configure system settings by using web ინტერფეისი.
2.1. ძიება cMT-G01/G02’s IP address
Launch UtilityManagerEX, select a cMT Series model, and then select a function from Reboot, Download, or Upload. The cMT Series HMI model or cMT-G01/G02 can be found in the IP/HMI Name groupbox by using the model’s IP address, even if the PC or laptop is not on the same network. UtilityManagerEX can find and change cMT-G01/G02’s IP address. The following settings can be carried out after obtaining the IP address.
2.2. Set in internet browser
Open internet browser (IE, Chrome, or Firefox), and enter cMT-G01/G02’s IP address (for example: 192.168.100.1) to configure cMT-G01/G02.
The default IP: Ethernet 1: DHCP, Ethernet 2: 192.168.100.1
cMT-G01/G02 system information is shown in the Login page.
| ხატულა | აღწერა |
 |
Displays HMI name. |
 |
Displays system date. |
 |
აჩვენებს სისტემის დროს. |
2.3. სისტემის დაყენება
The following part introduces cMT-G01/G02 system settings.
Three levels of privileges can be found:
[System Setting]: Controls all the settings
[Update]: Controls limited items.
[History]: Downloads history data (Recipes and Event Logs).
2.3.1. ქსელი
Configure Ethernet ports: IP, Mask, Gateway, and DNS.
cMT-G01 has two Ethernet ports. The default IP address of Ethernet 1 is DHCP, and the static IP address of Ethernet 2 is 192.168.100.1.
cMT-G02 has one Ethernet port, and is assigned from DHCP by default.
2.3.2. WiFi (cMT-G02)
Enable/Disable WiFi and related settings: search for AP, configuring IP, Mask, Gateway, and DNS.
2.3.3. თარიღი/დრო
Set RTC date and time. Select [Sync. with host] and then click [Save] to synchronize cMT-G01/G02 time with the computer time.
2.3.4. HMI Name
Enter a name to identify the unit.
[Identification light]: The green LED indicator of the unit will flash three times when this button is clicked, helping user to find the unit.
2.3.5. ისტორია
This tab offers settings related to historical data.
[Clear]: Clears history data.
[Backup]: Downloads history data in the unit to this computer.
2.3.6. ფოსტა
This tab offers settings related to email.
[SMTP]: Configure email server and relevant settings.
[Contacts]: Set email contacts in this tab.
[Update Email Contacts]: Import the email contacts built using Administrator Tools.
2.3.7. Project Management
This tab offers settings related to project management.
[Restart Project]: Restart cMT-G01/G02 project.
[Update Project]: Upload the project’s *.cxob file to cMT-G01/G02.
[Backup Project]: Backup the project file to this computer.
2.3.8. System Password
Set login password and the password for transferring project file.
2.3.9. Enhanced Security
The account setting in this tab can determine the accounts that can log in OPC UA.
[Accounts]: Add user or change user password and operable classes.
[Import User Account]: Import the user accounts built in Administrator Tools.
2.3.10. EasyAccess 2.0
This tab shows Hardware Key, EasyAccess 2.0 activate status, and proxy settings.
For more information on EasyAccess 2.0, please see EasyAccess 2.0 User Manual.
2.3.11. OPA UA
Configure OPC UA settings. Please see Chapter 6 in this manual for more information.
2.3.12. კომუნიკაცია
This tab displays the communication parameters of the device connected to cMT-G01/G02. The parameters can be changed.
Parameter list for the device connected via Serial Port.
Parameter list for the device connected via Ethernet Port.
Chapter3. Updating Web Package and OS
cMT-G01/G02 Web Package and OS can be updated through Ethernet. Launch Utility ManagerEX, select [cMT Series] » [Maintenance] » [cMT-G01 OS Upgrade].
3.1 განახლება Web პაკეტი
- Select an HMI to update OS.
- აირჩიეთ [Web package] and browse for the source file.
- Click [Update].
3.2 Updating OS
1. Select an HMI to update OS.
2. Select [OS], a Warning message shows, please read this message carefully before you click [OK].
3. If you click [OK], the cMT-G01 OS Update window opens again, browse for the source file, and then click [Update].
4. The message window below opens, please do not turn off the power while upgrading.
5. When finished, cMT-G01 OS Update window shows “finished”.
Chapter4. How to create a cMT-G01/G02 project
This chapter explains how to create a project when cMT-G01/G02 is used as an OPC UA Server, and how to set the addresses used to communicate with OPC UA Clients. The basic steps are:
- Add a driver into Device List in EasyBuilder Pro.
- Enable OPC UA Server and designate communication address.
- Download the project to HMI.
The following explains how to set up OPC UA Server in the project.
4.1. Create a new project
Step 1. Launch EasyBuilder Pro and select a cMT-G01/G02.
Step 2. Add a PLC into the Device List.
Step 3. Click [IIoT] » [OPC UA Server], and select [Enable] check box to enable OPC UA Server.
Step 4. Click [Tags] of the device and then click [New Tag] to add tags monitored using OPC UA.
When finished, click [OK] to leave.
Step 5. Find the created tags in OPC UA Server window. Larger quantity of tags can be exported as csv/excel file and then imported for editing.
4.2. Download project to cMT-G01/G02
The format of the project file run on cMT-G01/G02 is *.cxob. In EasyBuilder Pro, click [Project] » [Compile] to compile the project into *.cxob format. When finish compiling, you can download the project to cMT-G01/G02 by two ways.
Way 1: Download using EasyBuilder Pro. Click [Project] » [Download], and set HMI IP address. The project can be downloaded via Ethernet.
Way 2: Download using website. Open internet browser (IE, Chrome, Firefox), enter cMT-G01/G02 IP address (for example: 192.168.100.1), click System Setting, enter password, and then configure cMT-G01/G02 settings. Go to [Project Management] page and open [Upload Project] tab to download the project file from the computer to cMT-G01/G02.
4.3. Monitoring OPC UA Client
After downloading the project file to HMI, use OPC UA Client software to connect with cMT-G01/G02 to monitor PLC data.
Note: The above is a screenshot of UaExport settings window, for more information on OPC UA Client software settings, please see software’s manual.
4.4. On-line/Off-line Simulation
Running On-line or Off-line simulation in EasyBuilder Pro helps you examine OPC UA Tag settings. In On-line simulation, cMT Diagnoser can read from / write to PLC. Please note that On-line simulation is limited to 10 minutes.
Step 1. In EasyBuilder Pro click [Project] » [On-line Simulation] / [Off-line Simulation] to open cMT Diagnoser window.
Step 2. Add the tags to be previewed into the Monitor list on the right side.
Step 3. In On-line Simulation, data in PLC tags will also change.
Chapter5. Functions supported by cMT-G01/G02
- OPC UA სერვერი
http://www.weintek.com/download/EBPro/Document/UM016009E_OPC_UA_UserManual_en.pdf - EasyAccess 2.0
- http://www.weintek.com/download/EasyAccess20/Manual/eng/EasyAccess2_UserManual_en.pdf
- Modbus TCP/IP Gateway
- MQTT
- Administrator Tools
- Time synchronization (NTP)
- მაკრო
- Project protection
- Communication with iE/XE/eMT/mTV HMI models.
- გადასასვლელი
- Data Transfer (Global) object
- Off-line / On-line Simulation
- Recipes (RW, RW_A)
- Event Log (please note that cMT-G01/G02 cannot read history data saved in an external device)
- ელ.ფოსტა
- განრიგი
- Managing OPC UA and communication parameters using Web ინტერფეისი.
Chapter6. OPC UA Web მენეჯმენტის ინტერფეისი
6.1. შესავალი
cMT-G01/G02 provides a web-based tool for convenient access to OPC UA configurations.
Open cMT-G01/G02’s webpage by entering its IP address into the address bar of a web browser. At the entry page, log in with System setting’s password. Factory default of the password is 111111.
(Suggested resolution: 1024×768 or higher)
Navigate to the OPC UA configuration page from the context menu on the left.
The OPC UA configuration page consists of a Startup/Shutdown control with status bar and tabbed windows including: Server settings, Edit node, Certificates, Discovery, and Advanced.
Usage of each window tab:
| ჩანართი | აღწერა |
| სერვერის პარამეტრები | Configure server settings such as port, name, security, user authentication……etc. |
| Edit node | მართვა tags used by OPC UA server. |
| სერთიფიკატები | Manage certificates used by OPC UA server. |
| აღმოჩენა | Manage list of discovery server. |
| გაფართოებული | Advanced options and features. |
6.2. Startup / Shut Down
Use the toggle button to start up or shut down the OPC UA server. If there is active client connection, when shutting down, the server will wait for a few seconds before closing off completely.
In addition, both the toggle button and a line of text also indicate the status of the server. The status is refreshed approximately every 10 seconds. An icon on the right 
indicates that the status is being refreshed.
ბოლო წერტილი URL is also displayed for user’s reference.
*Whenever a page refresh is desired, use the menu on the left. Avoid using the browser’s refresh button to reload a tab as you may be asked to enter the password to log in again.
6.3. Server Settings
The Server settings page shows general configurations of the OPC UA server.
| გენერალი | ფუნქცია |
| პორტი | Access port of the OPC UA server |
| სერვერის სახელი | Server name of the OPC UA server |
| Დაცვის პოლიცია | Supported security policies. At least one must be selected. Supported Policy: None, Basic128Rsa15, Basic256, Basic256sha256 Mode: Sign, Sign & Encrypt |
| ვარიანტი | Automatically Trust all client certificates: by enabling this option, the OPC UA server will trust the certificate from any client connection. |
OPC UA server must be configured with at least one user authentication mode as listed in the following table.
| ავთენტიფიკაცია | აღწერილობები |
| ანონიმური | Allow anonymous client connection. At least one of Browse, Read, or Write modes must be selected. |
| User name & Password | Allow user authentication with username and password. Each access mode, browse, read, and write can be assigned to a user class. User classes are configured in the Enhanced Security mode on the web interface or in EasyBuilder Pro. |
| სერთიფიკატი | User authentication with X.509 certificate |
After completing settings, click the Save button to save the changes. OPC UA server will shut down momentarily and then restart for the changes to take effect.
6.4. Edit Node
In this page, the user can view და მართეთ tags currently available in the OPC UA server. New nodes and groups can be added, while existing nodes and groups can be edited or deleted. For ease of navigation, detail information of the currently selected node/group is displayed on the right. After completing settings, it is necessary to click the Save button to save the changes. OPC UA server will shut down momentarily and then restart for the changes to take effect. Changes will be lost if one exits this page without saving.
Note that all modifications can only be made for existing drivers. It is not possible to change or add other drivers that are not already available. It is also not possible to edit the nodes used by tag PLCs*.
*Tag PLCs are characterized by their use of name tags as device memory address as opposed to using device name with indices. Examples of tag PLCs include: BACnet, Rockwell Free Tag Names , Siemens S7-1200,…etc.
6.5. სერთიფიკატები
In this page, the user can manage certificates and revocation lists of the OPC UA server. Use the dropdown menu to access each page.
If “Allow anonymous client connection” (in the Server settings tab ) option is not active, OPC UA server will reject all client connections and place their certificates in the untrusted list. User may manually “trust” them in this page. Use the reload button to repopulate the list of certificates if necessary.
Similarly, currently trusted certificates can be manually rejected on the same page.
| გვერდი | აღწერა |
| Trusted Clients | Lists of trusted/rejected client certificates on the server. Supported operation: Trust/Reject, Remove, Import, Export. |
| Trusted Users | Lists of trusted/rejected user certificates on the server. Supported operation: Trust/Reject, Remove, Import, Export. |
| საკუთარი | Server’s own certificate. Supported operation: Update, Remove. When updating own certificate, matching certificate and Private Key must be uploaded together; otherwise, update will fail. A self-signed, 20-year validity certificate will be generated automatically if own certificate is absent when server starts up. |
| Trusted Client Issuers | List of trusted client issuer certificates. Supported operation: Import, Remove, Export. |
| Trusted User Issues | List of trusted client issuer certificates. Supported operation: Import, Remove, Export. |
| Certificate Revocation List | Certificate revocation lists for client, user, client issuer, and user issuer. Supported operation: Import, Remove, Export |
6.6. აღმოჩენა
OPC UA server can register itself with Local Discovery Servers. In this page, the user can maintain the list of discovery servers that OPC UA server will register with during startup. Should the discovery server be unavailable during server shutdown, the shutdown process will be slightly delayed.
After completing settings, click the Save button to save the changes. OPC UA server will shut down momentarily and then restart for the changes to take effect.
6.7. გაფართოებული
Additional settings can be configured in the Advanced tab. The user can set the trace logging level and specific startup behavior of the OPC UA server. Furthermore, the trace log can be downloaded.
After completing settings, click the Save button to save the changes. OPC UA server will shut down momentarily and then restart for the changes to take effect.
UM017003E_20200924
დოკუმენტები / რესურსები
 |
WEINTEK cMT-G01 Gateway Mod Bus TCP [pdf] მომხმარებლის სახელმძღვანელო cMT-G01, cMT-G02, cMT-G01 Gateway Mod Bus TCP, cMT-G01, Gateway Mod Bus TCP, Mod Bus TCP, Bus TCP |