Ffrâm Sengl Statig B2-SSCT
“
Manylebau:
- Table feet: 2 pcs
- Centre bracket: 1 pc
- Column (right): 1 pc
- Center rails: 2 pcs
- Allen Wrench (4mm): 1 pc
- Allen Wrench (5mm): 1 pc
Cyfarwyddiadau Defnydd Cynnyrch:
Cyfarwyddiadau Cynulliad:
- Cam 1: Llaciwch y bolltau sydd wedi'u gosod ymlaen llaw a
addaswch hyd y ffrâm uchaf i gyd-fynd â maint y bwrdd
brig. - Cam 2: Insert the Column into the top frame,
fix the lifting column with 4pcs screws M6x12. - Cam 3: Place the table feet on the Column,
rotate it to align, then tighten the pre-installed bolt. - Cam 4: Rhowch y braced ochr ar y brig
ffrâm a thynhau'r bolltau. - Cam 5: Mount the tabletop and fix it with 14
pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10.
Tighten the pre-installed bolts on the top frame.
Gosod Hambwrdd Cebl:
- Cam 1: Trwsiwch y hambwrdd cebl (B2-SSCT) i'r
cable tray arms (B2-SSARM) with 8 pcs M6x10 screws. - Cam 2: Gosodwch y cromfachau U ar y ddesg
frame with 4 pcs M8x10 screws. Mount the cable tray to the desk
frame and fix it with 6 pcs M6x10 screws.
Gosod Panel Sgrin (Sgrin Preifatrwydd Shush30):
- Cam 1: Mewnosodwch y platiau wedi'u tapio i'r sgrin
panel (plates can be found in B2-SBRAC carton). - Cam 2: Install the screen brackets (B2-SBRAC)
to the Shush30 Extrusion with 8 pcs M5x6 screws. - Cam 3: Fix the screen brackets (B2-SBRAC) to
the desk frame with 10 pcs M6x10 screws.
Eco Panel Screen Panel Installation:
- Cam 1: Install the screen brackets (B2-SBRAC)
on the cable tray arm (B2-SSARM) with 10 PCS M6x10 Screws. The
brackets direction as photos display. - Cam 2: Rhowch y panel EPS ar y sgrin
brackets using a 6mm drill bit (not included), drill out holes in
Eco Panel Screen in line with back-to-back screen bracket holes.
Place 8 x Double Ended Bolts M5*32mm -6mm through The screen
bracket (B2-SBRAC) holes and the holes you have created in the Eco
Panel Screen. Tighten double-ended bolt with an Allen key.
Cwestiynau Cyffredin (FAQ):
- Q: How many table feet are included in the package?
- A: There are two table feet included.
- Q: What size screws are used for fixing the lifting
colofn? - A: You need to use 4pcs screws M6x12 for fixing the lifting
colofn. - Q: How many pcs of Allen Wrench are provided?
- A: There is one Allen Wrench of 4mm and one Allen Wrench of 5mm
a ddarperir yn y pecyn.
“`
Boost Static Single Frame Instruction Manual
1
Rhannau cydran
RHIF. Enw'r Gydran
PCS
RHIF. Enw'r Gydran
PCS
1
Traed bwrdd
2
9
Braced canol
1
2
Colofn (dde)
1
10 Rheiliau canolog
2
3
Bollt: M6x12
5
11 Ffrâm uchaf-2
1
4
Sgriw: ST4x20
22
12 Column( left)
1
5
Cromfachau ochr
2
13 Wrench Allen (4mm)
1
6
Pad rwber
14
14 Wrench Allen (5mm)
1
7
Ffrâm uchaf-1
1
15 Tei Cebl
5
8
Bollt: M6x10
3
2
Cyfarwyddiadau Cymanfa
Cam 1 Llaciwch y bolltau sydd wedi'u gosod ymlaen llaw ac addaswch hyd y ffrâm uchaf i gyd-fynd â maint top y bwrdd.
Step 2 Inset the Column to the top frame,fix lifting column with 4pcs screws M6x12 like.
3
Step 3 Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
Cam 4 Rhowch y braced ochr ar y ffrâm uchaf a thynhau'r bolltau.
4
Step 5 Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10 Tighten the pre-installed bolts on the top fame
5
Gosod hambwrdd cebl Cam 1 – Trwsiwch yr hambwrdd cebl (B2-SSCT) i freichiau'r hambwrdd cebl (B2-SSARM) gydag 8 darn o sgriwiau M6x10.
Cam 2 – Gosodwch y bracedi U i ffrâm y ddesg gyda 4 darn o sgriwiau M8x10. – Mowntiwch y hambwrdd cebl i ffrâm y ddesg a'i drwsio gyda 6 darn o sgriwiau M6x10
6
Gosod panel sgrin (Sgrin Preifatrwydd Shush30) Cam 1 – Mewnosodwch y platiau wedi'u tapio i'r panel sgrin (mae'r platiau i'w cael yng ngharton B2-SBRAC)
Cam 2 – Gosodwch y bracedi sgrin (B2-SBRAC) i'r Allwthiad Shush30 gydag 8 darn o sgriwiau M5x6.
7
Cam 3 – Trwsiwch y bracedi sgrin (B2-SBRAC) i ffrâm y ddesg gyda 10 darn o sgriwiau M6x10.
8
Gosod panel sgrin EPS (Panel Eco 900mm U) Cam 1 – Gosodwch y bracedi sgrin (B2-SBRAC) ar fraich y hambwrdd cebl (B2-SSARM) gyda 10 Sgriw M6x10
Cyfeiriad y cromfachau fel y dangosir yn y lluniau.
Cam 2 – Rhowch y panel EPS ar y bracedi sgrin Gan ddefnyddio darn dril 6mm (heb ei gynnwys), driliwch dyllau yn Sgrin y Panel Eco yn unol â thyllau bracedi sgrin cefn wrth gefn (Nodyn: Mae Darnau Dril Carbid yn Gweithio Orau ar gyfer panel PET) – Rhowch 8 x Bollt Dwbl M5* 32mm – 6mm trwy dyllau'r braced sgrin (B2-SBRAC) a'r tyllau rydych chi wedi'u creu yn Sgrin y Panel Eco. Tynhau'r bollt dwbl gydag allwedd Allen.
9
Dogfennau / Adnoddau
 |
Boost B2-SSCT Static Single Frame [pdfLlawlyfr Cyfarwyddiadau B2-SSCT, B2-SSARM, B2-SBRAC, B2-SSCT Static Single Frame, B2-SSCT, Static Single Frame, Single Frame, Frame |