Ipataas ang B2-SSCT Static Single Frame

Mga detalye

• Table feet: 2 pcs
• Centre bracket: 1 pc
• Column (right): 1 pc
• Center rails: 2 pcs
• Allen Wrench (4mm): 1 pc
• Allen Wrench (5mm): 1 pc

Mga Instruksyon sa Paggamit sa Produkto

Mga Instruksyon sa Asembliya

1. Lakang 1: Buksi ang pre-installed bolts ug i-adjust ang gitas-on sa ibabaw nga frame aron mohaum sa gidak-on sa table top.
2. Lakang 2: Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Lakang 3: Place the table feet on the Column, rotate it to align, then tighten the pre-installed bolt.
4. Lakang 4: Ibutang ang kilid nga bracket sa ibabaw nga frame ug hugti ang mga bolts.
5. Lakang 5: Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10. Tighten the pre-installed bolts on the top frame.

Pag-instalar sa Cable Tray

1. Lakang 1: Fix the cable tray (B2-SSCT) to the cable tray arms (B2-SSARM) with 8 pcs M6x10 screws.
2. Lakang 2: Install the U brackets to the desk frame with 4 pcs M8x10 screws. Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws.

Pag-instalar sa Screen Panel (Shush30 Privacy Screen)

1. Lakang 1: Insert the tapped plates into the screen panel (plates can be found in the B2-SBRAC carton).
2. Lakang 2: Install the screen brackets (B2-SBRAC) to the Shush30 Extrusion with 8 pcs M5x6 screws.
3. Lakang 3: Fix the screen brackets (B2-SBRAC) to the desk frame with 10 pcs M6x10 screws.

Eco Panel Screen Panel Installation

1. Lakang 1: Install the screen brackets (B2-SBRAC) on the cable tray arm (B2-SSARM) with 10 PCS M6x10 Screws. The direction as the photos display.
2. Lakang 2: Place the EPS panel on the screen brackets using a 6mm drill bit (not included), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes.
   • Place 8 x Double Ended Bolts M5*32mm -6mm through the screen bracket (B2-SBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with an Allen key.

Mga bahin sa sangkap

DILI.	Ngalan sa Component	PCS
1	Mga tiil sa lamesa	2
2	Kolum (tuo)	1
3	Bolt: M6x12	5
4	Screw: ST4x20	22
5	Mga braket sa kilid	2
6	Goma pad	14
7	Ibabaw nga bayanan-1	1
8	Bolt: M6x10	3

DILI.	Ngalan sa Component	PCS
9	Center bracket	1
10	Mga riles sa sentro	2
11	Ibabaw nga bayanan-2	1
12	Column( left)	1
13	Allen Wrench (4mm)	1
14	Allen Wrench (5mm)	1
15	Higot sa Kable	5

Mga Instruksyon sa Asembliya

1. Lakang 1
   • Buksi ang pre-installed bolts ug i-adjust ang gitas-on sa ibabaw nga frame aron mohaum sa gidak-on sa table top.
2. Lakang 2
   • Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Lakang 3
   • Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
4. Lakang 4
   • Ibutang ang kilid nga bracket sa ibabaw nga frame ug hugti ang mga bolts.
5. Lakang 5
   • I-mount ang tabletop ug ayoha kini gamit ang 14 pcs screws ST4x20;
   • Fix the centre bracket with 2 pcs of screws M6x10.
   • Hupti ang pre-installed bolts sa ibabaw nga frame.

Pag-instalar sa cable tray

1. Lakang 1
   • Ayuhon ang cable tray(B2-SSCT) sa cable tray arms(B2-SSARM) nga adunay 8 pcs M6x10 screws.
   • Lakang 2
   • I-install ang U bracket sa desk frame nga adunay 4 pcs M8x10 screws.
   • I-mount ang cable tray sa desk frame ug ayoha kini gamit ang 6 pcs M6x10 screws

Pag-instalar sa screen panel ( Shush30 Privacy Screen )

1. Lakang 1
   • Insert the tapped plates into the screen panel ( plates can be found in the B2-SBRAC carton )
2. Lakang 2
   • I-install ang mga screen bracket (B2-SBRAC) sa Shush30 Extrusion nga adunay 8 pcs M5x6 screws.
3. Lakang 3
   • I-ayo ang screen bracket (B2-SBRAC) sa desk frame nga adunay 10 pcs M6x10 screws.

EPS (900mm H Eco Panel) Pag-instalar sa screen panel

1. Lakang 1
   • Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10 Screws
   • The direction as the photos display.
2. Lakang 2
   • Ibutang ang EPS panel sa mga bracket sa screen
   • Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
   • Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.

Kanunay nga Gipangutana nga mga Pangutana

How many table feet are included in the package?

There are two table feet included.

What size screws are used for fixing the lifting column?

You need to use 4pcs of screws M6x12 for fixing the lifting column.

How many pcs of Allen Wrench are provided?

There is one Allen Wrench of 4mm and one Allen Wrench of 5mm provided in the package.

Mga Dokumento / Mga Kapanguhaan

Ipataas ang B2-SSCT Static Single Frame [pdf] Manwal sa Instruksyon B2-SSCT, B2-SSARM, B2-SBRAC, B2-SSCT Static Single Frame, B2-SSCT, Static Single Frame, Single Frame, Frame

Mga pakisayran

• Manwal sa Gumagamit