Boost B2-SSCT Static Ib Ncej

Specifications

• Table feet: 2 pcs
• Centre bracket: 1pc ib
• Column (right): 1pc ib
• Center rails: 2 pcs
• Allen Ciaj (4mm): 1pc ib
• Allen Ciaj (5mm): 1pc ib

Cov lus qhia siv khoom

Cov lus qhia ua ke

1. Kauj ruam 1: Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
2. Kauj ruam 2: Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Kauj ruam 3: Place the table feet on the Column, rotate it to align, then tighten the pre-installed bolt.
4. Kauj ruam 4: Muab sab bracket rau ntawm tus ncej saum toj kawg nkaus thiab ceev cov bolts.
5. Kauj ruam 5: Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10. Tighten the pre-installed bolts on the top frame.

Cable Tais Installation

1. Kauj ruam 1: Fix the cable tray (B2-SSCT) to the cable tray arms (B2-SSARM) with 8 pcs M6x10 screws.
2. Kauj ruam 2: Nruab U brackets rau lub rooj ncej nrog 4 pcs M8x10 screws. Mount lub cable tais rau lub rooj ncej thiab kho nws nrog 6 pcs M6x10 screws.

Kev teeb tsa vaj huam sib luag (Shush30 Privacy Screen)

1. Kauj ruam 1: Insert the tapped plates into the screen panel (plates can be found in the B2-SBRAC carton).
2. Kauj ruam 2: Nruab qhov screen brackets (B2-SBRAC) rau Shush30 Extrusion nrog 8 pcs M5x6 screws.
3. Kauj ruam 3: Kho qhov screen brackets (B2-SBRAC) rau lub rooj ncej nrog 10 pcs M6x10 screws.

Eco Panel Screen Panel Installation

1. Kauj ruam 1: Install the screen brackets (B2-SBRAC) on the cable tray arm (B2-SSARM) with 10 PCS M6x10 Screws. The direction as the photos display.
2. Kauj ruam 2: Place the EPS panel on the screen brackets using a 6mm drill bit (not included), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes.
   • Place 8 x Double Ended Bolts M5*32mm -6mm through the screen bracket (B2-SBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with an Allen key.

Cov khoom seem

TSIS MUAJ.	Lub Npe Lub Npe	PCS
1	Rooj taw	2
2	Kem (txoj cai)	1
3	Loj: M6x12	5
4	Ntsia Hlau: ST4x20	22
5	Sab brackets	2
6	Roj hmab ncoo	14
7	Sab saum toj-1	1
8	Loj: M6x10	3

TSIS MUAJ.	Lub Npe Lub Npe	PCS
9	Center bracket	1
10	Center rails	2
11	Sab saum toj-2	1
12	Column( left)	1
13	Allen Wrench (4 hli)	1
14	Allen Wrench (5 hli)	1
15	Cable Tie	5

Cov lus qhia ua ke

1. Kauj ruam 1
   • Loosen the pre-installed bolts and adjust the length of the top frame to match the size of the table top.
2. Kauj ruam 2
   • Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Kauj ruam 3
   • Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
4. Kauj ruam 4
   • Muab sab bracket rau ntawm tus ncej saum toj kawg nkaus thiab ceev cov bolts.
5. Kauj ruam 5
   • Mount the tabletop and fix it with 14 pcs screws ST4x20;
   • Fix the centre bracket with 2 pcs of screws M6x10.
   • Tighten lub pre-installed bolts nyob rau sab saum toj ncej.

Cable tais installation

1. Kauj ruam 1
   • Fix the cable tray(B2-SSCT ) to the cable tray arms(B2-SSARM) with 8 pcs M6x10 screws.
   • Kauj ruam 2
   • Nruab U brackets rau lub rooj ncej nrog 4 pcs M8x10 screws.
   • Mount lub cable tais rau lub rooj ncej thiab kho nws nrog 6 pcs M6x10 screws

Kev teeb tsa vaj huam sib luag ( Shush30 Privacy Screen )

1. Kauj ruam 1
   • Insert the tapped plates into the screen panel ( plates can be found in the B2-SBRAC carton )
2. Kauj ruam 2
   • Nruab qhov screen brackets (B2-SBRAC) rau Shush30 Extrusion nrog 8 pcs M5x6 screws.
3. Kauj ruam 3
   • Kho qhov screen brackets (B2-SBRAC) rau lub rooj ncej nrog 10 pcs M6x10 screws.

EPS (900mm H Eco Vaj Huam Sib Luag) Kev teeb tsa vaj huam sib luag

1. Kauj ruam 1
   • Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10 Screws
   • The direction as the photos display.
2. Kauj ruam 2
   • Muab lub vaj huam sib luag EPS tso rau ntawm qhov screen brackets
   • Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
   • Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.

Cov lus nug nquag

How many table feet are included in the package?

There are two table feet included.

What size screws are used for fixing the lifting column?

You need to use 4pcs of screws M6x12 for fixing the lifting column.

How many pcs of Allen Wrench are provided?

There is one Allen Wrench of 4mm and one Allen Wrench of 5mm provided in the package.

Cov ntaub ntawv / Cov ntaub ntawv

Boost B2-SSCT Static Ib Ncej [ua pdf] Phau ntawv qhia B2-SSCT, B2-SSARM, B2-SBRAC, B2-SSCT Static Ib Ncej, B2-SSCT, Static Ib Ncej, Ib Ncej, Ncej

Cov ntaub ntawv

• Cov neeg siv phau ntawv