B2-SSCT Static Single Frame
“
පිරිවිතර:
- Table feet: 2 pcs
- Centre bracket: 1 pc
- Column (right): 1 pc
- Center rails: 2 pcs
- Allen Wrench (4mm): 1 pc
- Allen Wrench (5mm): 1 pc
නිෂ්පාදන භාවිත උපදෙස්:
එකලස් කිරීමේ උපදෙස්:
- පියවර 1: Loosen the pre-installed bolts and
adjust the length of the top frame to match the size of the table
ඉහළ. - පියවර 2: Insert the Column into the top frame,
fix the lifting column with 4pcs screws M6x12. - පියවර 3: Place the table feet on the Column,
rotate it to align, then tighten the pre-installed bolt. - පියවර 4: Place the side bracket on the top
frame and tighten the bolts. - පියවර 5: Mount the tabletop and fix it with 14
pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10.
Tighten the pre-installed bolts on the top frame.
කේබල් තැටි ස්ථාපනය:
- පියවර 1: Fix the cable tray (B2-SSCT) to the
cable tray arms (B2-SSARM) with 8 pcs M6x10 screws. - පියවර 2: Install the U brackets to the desk
frame with 4 pcs M8x10 screws. Mount the cable tray to the desk
frame and fix it with 6 pcs M6x10 screws.
Screen Panel Installation (Shush30 Privacy Screen):
- පියවර 1: තට්ටු කළ තහඩු තිරයට ඇතුළු කරන්න
panel (plates can be found in B2-SBRAC carton). - පියවර 2: Install the screen brackets (B2-SBRAC)
to the Shush30 Extrusion with 8 pcs M5x6 screws. - පියවර 3: Fix the screen brackets (B2-SBRAC) to
the desk frame with 10 pcs M6x10 screws.
පරිසර පැනල් තිර පැනල් ස්ථාපනය:
- පියවර 1: Install the screen brackets (B2-SBRAC)
on the cable tray arm (B2-SSARM) with 10 PCS M6x10 Screws. The
brackets direction as photos display. - පියවර 2: EPS පැනලය තිරය මත තබන්න.
brackets using a 6mm drill bit (not included), drill out holes in
Eco Panel Screen in line with back-to-back screen bracket holes.
Place 8 x Double Ended Bolts M5*32mm -6mm through The screen
bracket (B2-SBRAC) holes and the holes you have created in the Eco
Panel Screen. Tighten double-ended bolt with an Allen key.
නිතර අසන ප්‍රශ්න (FAQ):
- Q: How many table feet are included in the package?
- A: There are two table feet included.
- Q: What size screws are used for fixing the lifting
column? - A: You need to use 4pcs screws M6x12 for fixing the lifting
තීරුව. - Q: How many pcs of Allen Wrench are provided?
- A: There is one Allen Wrench of 4mm and one Allen Wrench of 5mm
පැකේජයේ සපයා ඇත.
"`
Boost Static Single Frame Instruction Manual
1
සංරචක කොටස්
නැත. සංරචක නම
PCS
නැත. සංරචක නම
PCS
1
මේස අඩි
2
9
මධ්‍ය වරහන
1
2
තීරුව (දකුණ)
1
10 Center rails
2
3
බෝල්ට්: M6x12
5
11 Top frame-2
1
4
ඉස්කුරුප්පු ඇණ: ST4x20
22
12 Column( left)
1
5
පැති වරහන්
2
13 ඇලන් රෙන්ච් (මි.මී. 4)
1
6
රබර් පෑඩ්
14
14 ඇලන් රෙන්ච් (මි.මී. 5)
1
7
ඉහළ රාමුව-1
1
15 කේබල් ටයි පටිය
5
8
බෝල්ට්: M6x10
3
2
එකලස් කිරීමේ උපදෙස්
පියවර 1 පෙර ස්ථාපනය කර ඇති බෝල්ට් ලිහිල් කර මේසයේ මුදුනේ ප්‍රමාණයට ගැලපෙන පරිදි ඉහළ රාමුවේ දිග සකසන්න.
Step 2 Inset the Column to the top frame,fix lifting column with 4pcs screws M6x12 like.
3
Step 3 Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
පියවර 4 ඉහළ රාමුව මත පැති වරහන තබා බෝල්ට් තද කරන්න.
4
Step 5 Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10 Tighten the pre-installed bolts on the top fame
5
Cable tray installation Step 1 – Fix the cable tray(B2-SSCT ) to the cable tray arms(B2-SSARM) with 8 pcs M6x10 screws.
Step 2 – Install the U brackets to the desk frame with 4 pcs M8x10 screws. – Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws
6
Screen panel installation ( Shush30 Privacy Screen ) Step 1 – Insert the tapped plates to the screen panel ( plates can be found in B2-SBRAC carton )
Step 2 – Install the screen brackets ( B2-SBRAC )to the Shush30 Extrusion with 8 pcs M5x6 screws.
7
Step 3 – Fix the screen brackets ( B2-SBRAC ) to the desk frame with 10 pcs M6x10 screws.
8
EPS ( 900mm H Eco Panel ) Screen panel installation Step 1 – Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10 Screws
ඡායාරූප පෙන්වන පරිදි වරහන් දිශාව.
Step 2 – Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel ) – Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten double ended bolt with Allen key.
9
ලේඛන / සම්පත්
 |
Boost B2-SSCT Static Single Frame [pdf] උපදෙස් අත්පොත B2-SSCT, B2-SSARM, B2-SBRAC, B2-SSCT Static Single Frame, B2-SSCT, Static Single Frame, Single Frame, Frame |