ZEBRA TC58BE BT Mobile Computer User Guide

Ensure to use only Zebra approved accessories and battery packs.
Do not attempt to charge damp/wet devices. All components must be
dry before connecting to a power source.

Regulatory Markings

Check the device screen for regulatory markings. For details on
other country markings, refer to the Declaration of Conformity
(DoC) available at zebra.com/doc.

Health and Safety Recommendations

Consult with your local Health and Safety Manager to follow good
ergonomic workplace practices to prevent ergonomic injuries.

Vehicle Installation

Install the device properly to avoid interference with
electronic systems in vehicles. Position the device within easy
reach without causing driver distractions. Always comply with
national and local laws on distracted driving.

Safety on the Road

Focus on driving, obey laws regarding wireless device use while
driving, and avoid distracted driving.

Restricted Use Locations

Adhere to restrictions and instructions in restricted use
locations regarding electronic devices.

Safety in Hospitals and Aircraft

Switch off wireless devices when requested in hospitals or
aircraft to prevent interference with medical equipment or aircraft
operation. Maintain a separation distance of 20 cm from medical
devices to avoid interference.

Frequently Asked Questions (FAQ)

Q: Can I use non-Zebra approved accessories with the
device?

A: No, it is recommended to only use Zebra approved accessories
for safe operation.

Q: How far should I keep the device from medical devices?

A: Maintain a minimum separation distance of 20 cm (8 in.) from
medical devices like pacemakers to avoid interference.

Q: Is it safe to use the device while driving?

A: It is recommended to give full attention to driving and obey
laws on wireless device usage while driving to ensure safety.

“`

View Fullscreen

TC58BE/TC58AE/TC58CE /TC58JE Regulatory Guide
MN-004817-01EN-P May 21, 2024
Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA www.zebra.com
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2024 Zebra Technologies Corp. and/or its affiliates. All rights reserved.
Regulatory Information
This device is approved under Zebra Technologies Corporation. This guide applies to the following model numbers:
· TC58BE · TC58AE · TC58CE · TC58JE
All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / (BG) / (CZ) Peklad do místního jazyka / (DE) Übersetzung in die Landessprache / (EL) / (ES) Traducción de idiomas locales / (ET) Kohaliku keele tõlge / (FI) Paikallinen käännös / (FR) Traduction en langue locale / (HR) Prijevod na lokalni jezik / (HU) Helyi nyelv fordítás / (IT) Traduzione in lingua locale / (JA) / (KR) / (LT) Vietins kalbos vertimas / (LV) Tulkojums vietjvalod / (NL) Vertaling in lokale taal / (PL) Tlumaczenie na jzyk lokalny / (PT) Tradução do idioma local / (RO) Traducere în limba local / (RU) / (SK) Preklad do miestneho jazyka / (SL) Prevajanje v lokalni jezik / (SR) / (SV) Översättning av lokalt språk / (TR) Yerel dil çevirisi / (ZH-CN) / (ZH-TW) zebra.com/support Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user’s authority to operate the equipment. Declared maximum operating temperature: 50°C For use only with Zebra approved and UL Listed mobile devices, Zebra approved, and UL Listed/Recognized battery packs.

CAUTION: Only use Zebra approved and NRTL-certified accessories, battery packs, and battery chargers. Do NOT attempt to charge damp/wet mobile computers, printers or batteries. All components must be dry before connecting to an external power source.
Bluetooth® Wireless Technology
This is an approved Bluetooth® product. For more information on the Bluetooth SIG listing, please visit bluetooth.com.

Regulatory Markings
Regulatory markings subject to certification are applied to the device. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DoC is available at: zebra.com/doc.
The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the device by following these instructions:
Go to Settings > Regulatory.
Health and Safety Recommendations
Ergonomic Recommendations
In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
Vehicle Installation
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (including safety systems). Check with the manufacturer or its representative regarding your vehicle. Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer about any equipment that has been added to your vehicle.
Position the device within easy reach. User should be able to access the device without removing their eyes from the road.
IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.
Safety on the Road Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the areas where you drive.
The wireless industry reminds you to use your device / phone safely when driving.
Restricted Use Locations
Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in restricted use locations.
Safety in Hospitals and Aircraft
Wireless devices transmit radio frequency energy that may affect medical electrical equipment and aircraft’s operation. Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are designed to prevent possible interference with sensitive equipments.
It is recommended that a minimum separation distance of 20 cm (8 in.) be maintained between a wireless device and a medical devices such as pacemakers, defibrillator, or other implantable devices to avoid potential interference with the medical device. Pacemaker users should keep the device at the opposite side of the pacemaker or turn OFF the device if suspected of interference.
Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device.

RF Exposure Guidelines
Safety Information
Reducing RF Exposure Use Properly Only operate the device in accordance with the instructions supplied.
The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at zebra.com/doc.
Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide.
The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided.
For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at zebra.com/responsibility.
Handheld or Body-Worn Devices To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5 cm or more from a user’s body and nearby persons.
To satisfy RF exposure requirements, this device must be hand-held only and, where applicable, used only with Zebra tested and approved accessories.

Optical Devices
Laser Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful.
CAUTION: Use of controls, adjustments, or the performance of procedures other than those specified in the supplied product documentation may result in hazardous laser light exposure.
SE5500
· Wavelength: 500-570 · Maximum output: 1 mW · Pulse duration: 4 ms · Beam divergence: 18 ° · Repetition rate: 16.7 ms
SE4770
· Wavelength: 630-680 · Maximum output: 1 mW · Pulse duration: 12.5 ms · Beam divergence: 42.7 ° · Repetition rate: 16.9 ms
Scanner Labeling

Complies with 21 CFR1040.10 and 1040.11, except for deviations pursuant to Laser Notice No. 56,

dated May 08, 2019 and IEC/EN 60825-1:2014

1
Labels read:

1. Laser Light – do not stare into beam. Class 2 Laser product. 630-680mm,1mW (applies to SE4770)
Laser Light – do not stare into beam. Class 2 Laser product. 500-570mm,1mW (applies to SE5500)
2. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 56, dated May 08, 2019 and IEC/EN 60825-1:2014.
LED Risk Group classified according to IEC 62471:2006 and EN62471:2008.
· SE4770 Pulse Duration: 17.7 ms · SE5500 Pulse Duration: CW · SE4720 Pulse Duration: 17.7 ms
Power Supply
WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE SELV power supply with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous.
Batteries and Power Packs
This information applies to Zebra-approved batteries and power packs containing batteries.
Battery Information CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries according to instructions.
Use only Zebra approved batteries. Accessories that have battery charging capability are approved for use with the following battery models:
· Model BT-000442 (3.85 VDC, 4680 mAh) · Model BT-000442B (3.85 VDC, 4680 mAh) · Model BT-000442A (3.85 VDC, 7000 mAh) · Model BT-000442C (3.85 VDC, 4680 mAh)
Zebra approved rechargeable battery packs are designed and constructed to the highest standards within the industry.
However, there are limitations as to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh environmental conditions, and severe drops.
When batteries are stored over six months, some irreversible deterioration in overall battery quality may occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half charge.
Replace the battery when a significant loss of run time is detected.
Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased separately or included as part of the host device. For more information on Zebra batteries, please visit zebra.com/batterydocumentation and select the Battery Best Practices link.
Battery Safety Guidelines IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
WARNING When using this product basic safety precautions should always be followed, including the following:
· The area in which the units are charged should be clear
of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non-commercial environment.
· Read all the instructions before using the product.

· Follow battery usage, storage, and charging guidelines
found in the user’s guide.
· Improper battery use may result in a fire, explosion, or
other hazard.
· Batteries subjected to extremely low air pressure may
result in an explosion or the leakage of flammable liquid or gas.
· To charge the mobile device battery, the battery and
charger temperatures must be between 0°C and 40°C (32°F and 104°F).
· Do not use incompatible batteries and chargers. Use of
an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Zebra support.
· Do not disassemble or open, crush, bend or deform,
puncture, or shred. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
· Severe impact from dropping any battery-operated
device on a hard surface could cause the battery to overheat.
· Do not short circuit a battery or allow metallic or
conductive objects to contact the battery terminals.
· Do not modify, disassemble, or remanufacture, attempt
to insert foreign objects into the battery, immerse or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard.
· Do not leave or store the equipment in or near areas
that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
· To reduce the risk of injury, close supervision is
necessary when used near children.
· Please follow local regulations to promptly dispose of
used re-chargeable batteries.
· Do not dispose of batteries in fire. Exposure to
temperatures over 100°C (212°F) may cause explosion.
· Seek medical advice immediately if a battery has been
swallowed.
· In the event of a battery leak, do not allow the liquid to
come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
· If you suspect damage to your equipment or battery,
contact Zebra support to arrange for inspection.
Marking and European Economic Area (EEA)
Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/65/EU.
Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformity is available at zebra.com/doc.
Environmental Compliance For compliance declarations, recycling information, and materials used for products and packaging please visit zebra.com/environment.
EU Importer : Zebra Technologies B.V Address: Mercurius 12, 8448 GX Heerenveen, Netherlands
Waste Electrical and Electronic Equipment (WEEE) For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at
zebra.com/weee.

United States and Canada Regulatory
Radio Frequency Interference Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and
receiver.
· Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV
technician for help.
· Operation of transmitters in the 5.925 – 7.125 GHz band
is prohibited for control of or communications with unmanned aircraft systems.
Radio Frequency Interference Requirements Canada
Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-003 (B)/NMB-003(B)
This device complies with Innovation, Science and Economic Development Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radio électrique subi même si le brouillage est susceptible d’en compromettre le fonctionnement.
This device is restricted to indoor use when operating in the 5150 – 5350 MHz frequency range.
Lorsqu’il fonctionne dans la plage de fréquences 5150 5350 MHz, cet appareil doit être utilisé exclusivement en extérieur.
Devices shall not be used for control of or communications with unmanned aircraft systems.
Les dispositifs ne doivent pas être utilisés pour commander des systèmes d’aéronef sans pilote ni pour communiquer avec de tels systèmes.
RF Exposure Requirements – FCC and ISED
The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of fcc.gov/oet/ea/fccid.
To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5 cm or more from a user’s body and nearby persons.
Pour satisfaire aux exigences d’exposition aux radio fréquences, cet appareil doit fonctionner avec une distance de séparation minimale de 1.5 cm ou plus de corps d’une personne.

To satisfy RF exposure requirements, this device must be hand-held only and, where applicable use only with Zebra tested and approved accessories.
Hotspot Mode
To satisfy RF exposure requirements in hotspot mode, this device must operate with a minimum separation distance of 1.0 cm or more from a user’s body and nearby persons.
Pour satisfaire aux exigences d’exposition RF en mode hotspot, cet appareil doit fonctionner avec une distance de séparation minimale de 1.0 cm ou plus du corps de l’utilisateur et des personnes à proximité.
Co-located Statement
To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those already approved in this filling.
Hotspot ISED Notice
When operating in hotspot mode, this device is restricted to indoor use when operating in the 5150 – 5350 MHz frequency range.
En mode de connexion partagée (hotspot), l’utilisation de cet appareil doit se faire exclusivement en extérieur lorsqu’il fonctionne dans la plage de fréquences 5150 5350 MHz.
Use with Hearing Aids – FCC When some wireless devices are used near some hearing devices (hearing aids and cochlear implants), users may detect a buzzing, humming, or whining noise. Some hearing devices are more immune than others to this interference noise, and wireless devices also vary in the amount of interference they generate. In the event of interference, you may want to consult your hearing aid supplier to discuss solutions.
The wireless telephone industry has developed ratings for some of their mobile phones to assist hearing device users in finding phones that may be compatible with their hearing devices. Not all phones have been rated. Zebra mobile devices that are rated have the rating included on the Declaration of Conformity (DoC) at zebra.com/doc.
The ratings are not guarantees. Results will vary depending on the user’s hearing device and hearing loss. If your hearing device happens to be vulnerable to interference, you may not be able to use a rated phone successfully. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs.
ANSI C63.19 Rating System
1. This phone is hearing aid compatible as determined by ANSI C63.19-2019.
2. This phone has been tested and certified for use with hearing aids for some of the wireless technologies that it uses. However, there may be some newer wireless technologies in this phone that have not been tested for use with hearing aids. It is important to try the different features of this phone thoroughly and in different locations, using your hearing aid or cochlear implant, to determine if you hear any interfering noise. Consult your service provider or the manufacturer of this phone for information on hearing aid compatibility. If you have questions about return or exchange policies, consult your service provider or phone retailer.
3. The ANSI C63.19-2019 standard does not use the M/T rating system for showing the hearing aid compatible of the phone that older version of the standard used. Instead, it uses the conversational gains for the phone’s hearing aid compatible capabilities.
4. The volume control performance has been evaluated according to ANSI C63.19-2019 and waiver DA-23-914. The lowest conversational gain is 19.58 dB with a hearing aid, and 18.00 dB without a hearing-aid.

Air Interface

Bands

Codec

Hearing Aid Compatibility (HAC)

T-Coil

Volume Control

LTE/NR/ Wi-Fi

LTE:2/4/5/7/1 2/13/14/17/25/ 26/30/38/41/4 8/66/71

AMR-NR/WB

Y(2)

NR:2/5/7/12/1 3/14/25/26/30/ 38/41/48/66/7 1/77/78

EVS-NB/WB

Wi-Fi:2.4 GHz, UNII1/2A/2C/3 /5(1)

EVS-SWB, Opus, G.711 a-Law 8 KHz, G.711 u-Law 8 KHz, G.729 8 KHz, G.722 16 KHz, GSM 8 KHz

UMTS

UMTS: II/IV/V

AMR-NB/WB

Y(2)

Opus, G.711 a-Law 8

KHz, G.711 u-Law 8

KHz, G.729 8 KHz,

G.722 16 KHz, GSM

8 KHz

Wi-Fi

UNII 5(1)/6/7/8

AMR-NR/W,

EVS-NB/WB, SWB,

Opus, G.711 a-Law 8

KHz, G.711 u-Law 8

KHz, G.729 8 KHz,

G.722 16 KHz, GSM

8 KHz

1: UNII-5 is tested for HAC for operations which are entirely below 6 GHz. Above 6 GHz is not tested due to outside of the current scope of ANSI C63.19 and FCC HAC regulations. 2: According to FCC waiver DA 23-914, HAC is only partially tested for the conversational gain.

UL Listed Products with GPS
Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire, shock, or casualties as outlined in UL’s Standard(s) for Safety for Information Technology Equipment. UL Certification does not cover the performance or reliability of the GPS hardware and GPS operating software. UL makes no representations, warranties, or certifications whatsoever regarding the performance or reliability of any GPS related functions of this product.
Marquage UL des produits équipés d’un GPS
Les tests menés par Underwriters Laboratories Inc. (UL) ne portent ni sur les performances, ni sur la fiabilité du matériel et du logiciel d’exploitation du GPS (Global Positioning System), ni sur tout autre aspect de ce produit. UL a uniquement testé la résistance au feu, aux chocs et aux sinistres, comme le définit la norme UL60950-1 relative à la sécurité des matériels de traitement de l’information. La certification UL ne couvre ni les performances, ni la fiabilité du matériel et du logiciel d’exploitation GPS. UL ne formule aucune déclaration, ni ne délivre aucune garantie ni aucun certificat concernant les performances et la fiabilité des fonctions GPS de ce produit.

Brasil
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.

zebra.com/support
: jwxk.miit.gov.cn :

SAR 2W/kg GB21288-2022 2W/kg 20W/m² GB21288-2022
CCC
” ” ISM 5000

SJ/T 11364
O: GB/T 26572
X: GB/T 26572 ( “×”

Colombia
Señor usuario, la siguiente información se entrega de conformidad con lo establecido en el Régimen de protección de los derechos de los usuarios, expedido por la Comisión de Regulación de Comunicaciones.
Recomendaciones de uso:
1. Utilice siempre que pueda dispositivos manos libres. 2. Evite utilizar el equipo mientras conduce un vehículo. 3. En caso que el teléfono sea utilizado por niños,
ancianos, mujeres embarazadas y población inmunocomprometida, consulte a su médico y el manual del equipo.
4. Si usted utiliza algún dispositivo electrónico de uso médico, asegúrese que el mismo esté protegido contra las ondas de radiofrecuencia externas.

5. Apague su teléfono en lugares tales como: hospitales, centros de salud, aviones, estaciones de suministro de combustible, en presencia de gases explosivos y lugares donde se realizan explosiones.
6. Evite que terceros hagan uso de su teléfono para prevenir la implantación de dispositivos como programas espías (spyware) o identificadores ocultos, que atentan contra la seguridad de la información contenida en el mismo.
France
Cet appareil a été testé et déclaré conforme aux limites applicables d’exposition aux radiofréquences (RF). Le débit d’absorption spécifique (DAS) local quantifie l’exposition de l’utilisateur aux ondes électromagnétiques de l’équipement concerné. Les valeurs SAR les plus élevées sont disponibles sur la déclaration de conformité (DoC) disponible sur: www.zebra.com/doc
India
The sending and receiving of texts is supported in the following Indian languages: Assamese, Bengali, Gujarati, Hindi, Kannada, Kashmiri, Konkani, Malayalam, Manipuri, Marathi, Nepali, Oriya, Punjabi, Sanskrit, Sindhi, Tamil, Telugu, Urdu, Bodo, Santhali, Maithili, and Dogri.
México
LOCALIZACIÓN DEL IMEI.
El IMEI está disponible en la etiqueta del producto y en la pantalla del dispositivo siguiendo estas instrucciones.
Opción 1: Ir a Ajustes > Acerca del teléfono.
Opción 2: Vaya a la aplicación Teléfono: Marque *#06
Este dispositivo está diseñado para recibir alertas de emergencia inalámbricas utilizando el Servicio de Radiodifusión Celular como se especifica en IFT-011 Pt3. Si su proveedor de red celular admite este servicio, se proporcionarán alertas mientras se encuentre en el área de cobertura del proveedor. Si viaja fuera del área de cobertura de su proveedor, es posible que las alertas no estén disponibles. Para obtener más información, póngase en contacto con su proveedor de red. La configuración de Alerta inalámbrica de emergencia está disponible en la configuración de la aplicación Mensajes seleccionando Avanzado. Una vez que se muestran las alertas, la configuración se puede ver y cambiar. Esto permite anular la selección de las alertas no obligatorias y habilitar las alertas de prueba si es necesario. También existe una opción para habilitar la conversión de texto a voz que permite que los mensajes de alerta de texto se hablen en voz alta para que el usuario escuche el mensaje.
Paraguay
En Paraguay este equipo deberá ser configurado para operar con las limitaciones establecidas en la Norma Técnica NTC-RF-918:2020 de la CONATEL.
Philippines
SMS blocking and spam reporting features are available as part of the standard Android SMS app. Instructions on how to activate these features are available on the Google Help website, support.google.com.
Singapore
End-users are required to obtain a site licence from the Infocomm Media Development Authority (“IMDA”) to operate RFID equipment in Singapore such as Zebra fixed and mobile RFID readers. For further information on this licensing requirement and the application process, end-users may contact IMDA (Tel: 6211 0647).

, zebra.com .
.
. (rra.go.kr) .

TC58BE SAR 2.0 W/kg 0.415 W/kg

/ 9 13
(EPA) 15
Türkiye
Bu cihaz Türkçe karakterlerin tamamini ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki sürümünkodu) ve ETSI TS 123.040 V8.1.0 (veya sonraki sürümün kodu) teknik özelliklerine uygundur.
TÜRK WEEE Uyumluluk Beyani EEE Yönetmeliine Uygundur.

.
(Specific Absorption Rate SAR)
· TC58BE 1.466 w/kg

United Kingdom
Statement of Compliance Non-radio devices: Zebra hereby declares that this equipment is in compliance with Electromagnetic Compatibility Regulations 2016, the Electrical Equipment (Safety) Regulations 2016 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.
Radio enabled devices: Zebra hereby declares that this equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity.

The full text of the UK Declaration of Conformities is available at: zebra.com/doc.
UK Importer: Zebra Technologies Europe Limited
Address: Dukes Meadow, Millboard Rd, Bourne End,
Buckinghamshire, SL8 5X
Warranty
For the complete Zebra hardware product warranty statement, go to: zebra.com/warranty.
Service Information
Before you use the unit, it must be configured to operate in your facility’s network and run your applications. If you have a problem running your unit or using your equipment, contact your facility’s Technical or System Support. If there is a problem with the equipment, they will contact Zebra support at zebra.com/support. For the latest version of the guide go to: zebra.com/support.
Software Support
Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in order to keep the device operating at peak performance levels. To confirm that your Zebra device has the latest entitled software available at the time of purchase, go to zebra.com/support. Check for the latest software from Support > Products, or search for the device and select Support > Software Downloads. If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at entitlementservices@zebra.com and ensure you include the following essential device information:
· Model number · Serial number · Proof of purchase · Title of the software download you are requesting.
If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to download the appropriate software.
Product Support Information
· For information on using this product, see the User
Guide at zebra.com/tc58e-info.
· To find quick answers to known product behaviors,
access our knowledge articles at supportcommunity.zebra.com/s/knowledge-base.
· Ask your questions in our Support community at
supportcommunity.zebra.com.
· Download product manuals, drivers, software, and view
how-to videos at zebra.com/support.
· To request a repair for your product, go to
zebra.com/repair.
Patent Information
To view Zebra patents, go to ip.zebra.com.

Documents / Resources

ZEBRA TC58BE BT Mobile Computer [pdf] User Guide
TC58BE, TC58BE BT Mobile Computer, BT Mobile Computer, Mobile Computer, Computer

References

User Manual

ZEBRA TC58BE BT Mobile Computer User Guide

TC58BE BT Mobile Computer

Product Specifications

Product Usage Instructions

Regulatory Information