JOMOX Mk II Panelboard CPU OS Nipasẹ SD Kaadi Urorack Module Lori Akoj Modular

Awọn pato

• Ọja: Alpha Base Mk II
• Ọna imudojuiwọn OS: kaadi SD
• Files Needed: AlphaMk2.bin for main system, ABSYSPan.bin for panel board CPU

Ṣiṣe imudojuiwọn Alpha Base Mk II OS nipasẹ kaadi SD:

1. Ṣe igbasilẹ ohun ti o nilo file AlphaMk2.bin and copy it to the root directory of the SD card.
2. Insert the SD card into the Alpha Base Mk II and press (DISK) to initiate the update process.
3. Lilö kiri lati fifuye eto OS file AlphaMk2.bin and press (Enter).
4. Confirm the update when prompted and wait for the programming to finish without turning off the device.
5. After completion, turn off and on the Alpha Base Mk II to see the new version number.

Nmu imudojuiwọn Alpha Base Mk II Panelboard CPU nipasẹ kaadi SD:

1. Ṣe igbasilẹ ohun ti o nilo file ABSYSPan.bin and copy it to the root directory of the SD card.
2. Insert the SD card into the Alpha Base Mk II and press (DISK) to start the update process.
3. Yan lati fifuye nronu Sipiyu OS file ABSYSPan.bin and confirm the update.
4. Allow the system blocks to be copied to the panel board CPU memory without interrupting the process.
5. Observe the LEDs indicating the updating progress and once completed, continue using the Alpha Base Mk II.

Ṣiṣe imudojuiwọn Alpha Base Mk II OS nipasẹ kaadi SD

1. Ṣe igbasilẹ tuntun julọ file „AlphaMk2.bin“ at https://www.jomox.de/upload/updates/AlphaMk2.bin to your computer. You can also find the file ni agbegbe ọja webojula ti o ba yi lọ si isalẹ lati imudojuiwọn files. Daakọ eyi file si awọn root liana ti awọn SD kaadi.
2. Insert the SD card to the Alpha Base Mk II. Press (DISK).
   • Iboju naa fihan:
     • W A V f o u n d : 2 5 4 T a r g e t : 0 0 1
     • A B W V 0 0 0 1 . r a w _ _ _ _ L o a d = E n t
   • If the disk does not open at first, take out the SD card, push it in again and try again.
   • Sometimes the unit has to warm up a bit to read the SD card properly. With every try first take out the card and push it in again.
3. Go right with the cursor until the display shows:
   • L o a d O S S y s t e m F i l e
   • A l p h a M k 2 . b i n _ _ _ _ L o a d = E n t
4. Now press (Enter). The display shows:
   • A t t e n t i o n O S U p d a t e !
     A r e y o u s u r e ? L o a d = E n t
5. Now press (Enter) again. The updating process starts and the system file yoo daakọ si iranti filasi. Lakoko ilana yii, o ko gbọdọ pa Alpha Base Mk II! Lẹhin iṣẹju diẹ ifihan naa ka:
   • P r o g r a m m i n g f i n i s h e d
   • T u r n u n i t o f f a n d o n
6. Now please turn the Alpha Base Mk II off and on again and see the new version number in the display.
   • Please note that, after updating, the global settings like preset no. are reset to default.
   • Pressing STO KIT writes the actual global settings to permanent memory again.
   • O n niyen.

Nmu awọn Alpha Base Mk II Panelboard Sipiyu OS nipasẹ SD kaadi

1. The Alpha Base MkII has a separate panel board CPU that performs the scanning of encoders and buttons, processes the RGB LEDs and the OLED graphics display. Download the most recent file „ABSYSPan.bin“ at  https://www.jomox.de/upload/updates/ABSYSPan.bin to your computer. You can also find the file ni agbegbe ọja webojula ti o ba yi lọ si isalẹ lati imudojuiwọn files. Daakọ eyi file si awọn root liana ti awọn SD kaadi.
2. Insert the SD card to the Alpha Base Mk II. Press (DISK).
   • Iboju naa fihan:
     • W A V f o u n d : 2 5 4 T a r g e t : 0 0 1
     • A B W V 0 0 0 1 . r a w _ _ _ _ L o a d = E n t
   • If the disk does not open at first, take out the SD card, push it in again and try again.
   • Sometimes the unit has to warm up a bit to read the SD card properly. With every try, first take out the card and push it in again.
3. Go right with the cursor until the display shows:
   • L o a d P a n e l C P U O S f i l e
   • A B S Y S P a n . b i n _ _ _ L o a d = E n t
4. Now press (Enter). The display shows:
   • P a n e l C P U O S U p d a t e !
   • A r e y o u s u r e? = E n t
5. Now press (Enter) again. The updating process starts, and the system blocks get copied to the panel board CPU memory.
   • • F r o n t P a n e l O S T r a n s m i s s i o n
   • The step LEDs light up in violet, indicating the blocks that count up. After a couple of seconds, the red LEDs start flashing and the actual updating takes place:
     • E x e c u t i n g F l a s h O S
       • W r i t e t o m e m o r y & r e s e t
   • Lakoko ilana yii, o ko gbọdọ pa Alpha Base Mk II!
6. Now the display shows
   • • P a n e l B o a r d C P U v e r 1 x
   • O le tẹ fun apẹẹrẹ KIT/SEQ ni bayi ati pe ifihan deede yoo han. O le tẹsiwaju lati ṣiṣẹ pẹlu Alpha Base MkII ni bayi laisi atunbere. Iyẹn ni.
   • AKIYESI:
     If, for some reason, the internal transmission failed and for instance this error message appears:
     • F r o n t P a n e l O S T r a n s m i s s i o n
     • M i s s i n g B l o c k s E r r o r
     • E x p e c t e d : 0 0 9 R e c e i v e d : 0 0 8
     • D u m p R e c e p t i o n C a n c e l l e d
   • Maṣe yọ ara rẹ lẹnu, kan pa ati lori ẹrọ naa ki o tun ṣe imudojuiwọn Iwaju Panel OS lẹẹkansi.

FAQs

Q: Kini MO le ṣe ti aṣiṣe ba waye lakoko ilana imudojuiwọn?

A: If an error occurs during the update process, refer to the user manual for troubleshooting steps or contact customer support for assistance.

Awọn iwe aṣẹ / Awọn orisun

JOMOX Mk II Panelboard CPU OS Nipasẹ SD Kaadi Urorack Module Lori Akoj Modular [pdf] Awọn ilana Mọl

Awọn itọkasi

• Itọsọna olumulo