JOMOX Mk II Panelboard CPU OS Via SD Card Urorack Module On Modular Grid

Špecifikácie

• Product: Alpha Base Mk II
• OS Update Method: SD card
• Files Needed: AlphaMk2.bin for main system, ABSYSPan.bin for panel board CPU

Updating the Alpha Base Mk II OS via SD card:

1. Stiahnite si požadované file AlphaMk2.bin and copy it to the root directory of the SD card.
2. Insert the SD card into the Alpha Base Mk II and press (DISK) to initiate the update process.
3. Navigate to load the OS system file AlphaMk2.bin and press (Enter).
4. Confirm the update when prompted and wait for the programming to finish without turning off the device.
5. After completion, turn off and on the Alpha Base Mk II to see the new version number.

Updating the Alpha Base Mk II Panelboard CPU OS via SD card:

1. Stiahnite si požadované file ABSYSPan.bin and copy it to the root directory of the SD card.
2. Insert the SD card into the Alpha Base Mk II and press (DISK) to start the update process.
3. Select to load Panel CPU OS file ABSYSPan.bin and confirm the update.
4. Allow the system blocks to be copied to the panel board CPU memory without interrupting the process.
5. Observe the LEDs indicating the updating progress and once completed, continue using the Alpha Base Mk II.

Updating the Alpha Base Mk II OS via SD card

1. Stiahnite si najnovšie file „AlphaMk2.bin“ at https://www.jomox.de/upload/updates/AlphaMk2.bin to your computer. You can also find the file in the product area of the website if you scroll down to the update files. Copy this file do koreňového adresára SD karty.
2. Insert the SD card to the Alpha Base Mk II. Press (DISK).
   • Na displeji sa zobrazí:
     • W A V f o u n d : 2 5 4 T a r g e t : 0 0 1
     • A B W V 0 0 0 1 . r a w _ _ _ _ L o a d = E n t
   • If the disk does not open at first, take out the SD card, push it in again and try again.
   • Sometimes the unit has to warm up a bit to read the SD card properly. With every try first take out the card and push it in again.
3. Go right with the cursor until the display shows:
   • L o a d O S S y s t e m F i l e
   • A l p h a M k 2 . b i n _ _ _ _ L o a d = E n t
4. Now press (Enter). The display shows:
   • A t t e n t i o n O S U p d a t e !
     A r e y o u s u r e ? L o a d = E n t
5. Now press (Enter) again. The updating process starts and the system file gets copied to flash memory. During this process, you MUST NOT turn off the Alpha Base Mk II! After a few seconds the display reads:
   • P r o g r a m m i n g f i n i s h e d
   • T u r n u n i t o f f a n d o n
6. Now please turn the Alpha Base Mk II off and on again and see the new version number in the display.
   • Please note that, after updating, the global settings like preset no. are reset to default.
   • Pressing STO KIT writes the actual global settings to permanent memory again.
   • To je všetko.

Updating the Alpha Base Mk II Panelboard CPU OS via SD card

1. The Alpha Base MkII has a separate panel board CPU that performs the scanning of encoders and buttons, processes the RGB LEDs and the OLED graphics display. Download the most recent file „ABSYSPan.bin“ at  https://www.jomox.de/upload/updates/ABSYSPan.bin to your computer. You can also find the file in the product area of the website if you scroll down to the update files. Copy this file do koreňového adresára SD karty.
2. Insert the SD card to the Alpha Base Mk II. Press (DISK).
   • Na displeji sa zobrazí:
     • W A V f o u n d : 2 5 4 T a r g e t : 0 0 1
     • A B W V 0 0 0 1 . r a w _ _ _ _ L o a d = E n t
   • If the disk does not open at first, take out the SD card, push it in again and try again.
   • Sometimes the unit has to warm up a bit to read the SD card properly. With every try, first take out the card and push it in again.
3. Go right with the cursor until the display shows:
   • L o a d P a n e l C P U O S f i l e
   • A B S Y S P a n . b i n _ _ _ L o a d = E n t
4. Now press (Enter). The display shows:
   • P a n e l C P U O S U p d a t e !
   • A r e y o u s u r e? = E n t
5. Now press (Enter) again. The updating process starts, and the system blocks get copied to the panel board CPU memory.
   • • F r o n t P a n e l O S T r a n s m i s s i o n
   • The step LEDs light up in violet, indicating the blocks that count up. After a couple of seconds, the red LEDs start flashing and the actual updating takes place:
     • E x e c u t i n g F l a s h O S
       • W r i t e t o m e m o r y & r e s e t
   • During this process, you MUST NOT turn off the Alpha Base Mk II!
6. Now the display shows
   • • P a n e l B o a r d C P U v e r 1 x
   • You can press e.g. KIT/SEQ now and the normal display will appear. You can continue to work with the Alpha Base MkII now without rebooting. That was it.
   • POZNÁMKA:
     If, for some reason, the internal transmission failed and for instance this error message appears:
     • F r o n t P a n e l O S T r a n s m i s s i o n
     • M i s s i n g B l o c k s E r r o r
     • E x p e c t e d : 0 0 9 R e c e i v e d : 0 0 8
     • D u m p R e c e p t i o n C a n c e l l e d
   • Don’t worry, just turn off and on the machine and do the Front Panel OS updating again.

často kladené otázky

Q: What should I do if an error occurs during the update process?

A: If an error occurs during the update process, refer to the user manual for troubleshooting steps or contact customer support for assistance.

Dokumenty / zdroje

JOMOX Mk II Panelboard CPU OS Via SD Card Urorack Module On Modular Grid [pdfPokyny Mk II Panelboard CPU OS Via SD Card Urorack Module On Modular Grid, Mk II, Panelboard CPU OS Via SD Card Urorack Module On Modular Grid, SD Card Urorack Module On Modular Grid, Urorack Module On Modular Grid, Module On Modular Grid, Modular Grid

Referencie

• Používateľská príručka