AiM K6 Bula Keypad Open Version
Litlhaloso
- Likonopo: K6 Open (6 programmable), K8 Open (8 programmable), K15 Open (15 programmable)
- Backlight: RGB e nang le khetho ea Dimming
- Khokahano: USB ka 7 Pins Binder 712 sehokelo sa basali
- Boitsebiso ba 'mele: Silicon ea rabara le PA6 GS30% e matlafalitsoeng
- Boholo:
- K6 Bula: 97.4x71x24mm
- K8 Bula: 127.4×71.4x24mm
- K15 Bula: 157.4×104.4x24mm
- Boima ba 'mele:
- K6 Bula: 120g
- K8 Bula: 150g
- K15 Bula: 250g
- Ha e kenelle metsi: IP67
Litaelo tsa Tšebeliso ea Sehlahisoa
Ho lokisa Keypad:
Khoasolla software ea RaceStudio3 ho tsoa ho AiM website at aim-sportline.com Sebaka sa ho jarolla software/firmware. Kenya software 'me u latele mehato ena:
Ho beha mekhoa ea Pushbutton:
U ka beha mekhoa e fapaneng bakeng sa konopo e 'ngoe le e' ngoe:
- MOMENTARY: E amahanya taelo ho konopo e 'ngoe le e' ngoe e kang Device Brightness command.
- MULTI-STATUS: E lumella konopo ea push ho nka litekanyetso tse fapaneng tse fetohang nako le nako ha e sutumetsoa.
Ho Beha Nako ea Nako:
Ho sa tsotelehe hore na ke mokhoa ofe, o ka beha moeli oa nako moo konopo ea pushe e behiloeng ka litekanyetso tse peli tse fapaneng ho latela hore na e sutumetsoa nako e kae. Lumella lebokose la tlhahlobo la tšebeliso ea nako ho lokisa tšobotsi ena.
Ho lokisa CAN Output Melaetsa:
O ka lokisa melaetsa ya CAN Output bakeng sa ho fetisa maemo a pushbutton le melaetsa ya CAN Input bakeng sa ho amohela maikutlo ho tswa lebaleng. Kenya li-tab tse amanang ho hlophisa sena.
Ho Romela Melaetsa:
Open Keypad e ka romela melaetsa e amehang ka lebelo le tsitsitseng kapa neng kapa neng ha ho e-na le phetoho libakeng tse fetisoang. Hlophisa maqhubu a phetiso ea molaetsa ha ho hlokahala.
LBH
P: Nka fumana boitsebiso bo eketsehileng hokae ka CAN Messages?
A: Ka kopo sheba tokomane e latelang bakeng sa tlhaiso-leseling ea CAN Message: CAN MessageFAQ
Selelekela
AiM Keypad Bula Version ke mefuta e mecha ea likatoloso tse kopaneng tse ipapisitseng le bese ea CAN. E fumaneha ka liphetolelo tse fapaneng ho ea ka palo ea li-pushbuttons tseo boemo ba tsona bo fetisitsoeng ka bese ea CAN. Likonopo ka bobeli le melaetsa ea CAN li ka lokisoa ka botlalo ka khokahano ea USB ho sebelisoa AiM RaceStudio 3 Software.
Konopo ka 'ngoe e ka hlophisoa joalo ka:
- Nakoana: boemo ba pushbutton bo ON ha konopo e sutumetsoa
- Toggle: boemo ba li-pushbutton bo fetoha ho tloha ho ON ho ea ho TIMA nako le nako ha konopo ea pushe e sutumetsoa
- Multistate: boleng ba pushbutton bo fetoha ho tloha ho 0 ho ea ho boleng bo phahameng nako le nako ha konopo ea pushe e sutumetsoa.
Ho feta moo, o ka hlalosa moeli oa nako bakeng sa konopo e 'ngoe le e' ngoe e hlalosang boitšoaro bo fapaneng ha ketsahalo ea khatello e KHUTSANE kapa E LONG e fumanoa.
Konopo e 'ngoe le e' ngoe e ka etsoa ka 'mala o fapaneng kapa ka mokhoa o tiileng, o liehang kapa o potlakileng oa ho panya.
Hape hoa khoneha ho hlalosa protocol ea CAN INPUT ho lumella 'mala oa LED hore o se ke oa amohela feela ketsahalo ea khatello ea konopo, empa hape o bonts'a boemo ba sesebelisoa.
Qetellong, hoa khoneha ho lokisa konopo ea push bakeng sa ho eketsa kapa ho fokotsa boemo ba khanya ea keypad.
| K6 Bula | K8 Bula | K15 Bula | |
| Likonopo | 6 e hlophisehileng | 8 e hlophisehileng | 15 e hlophisehileng |
| Backlight | RGB e nang le khetho ea Dimming | ||
| Khokahano | USB ka 7 Pins Binder 712 sehokelo sa basali | ||
| 'Mele Thepa | Silicon ea rabara le PA6 GS30% e matlafalitsoeng | ||
| Litekanyo | 97.4x71x4x24mm | 127.4×71.4×24 | 157.4×104.4×24 |
| Boima ba 'mele | 120g | 150g | 250g |
| Ha e kenele metsi | IP67 | ||
Li-kits tse fumanehang ka boikhethelo le likarolo tse ling
Mefuta e fumanehang ea keypad e fumanehang ke:
- Keypad K6 Bula
- Keypad K6 Bula + 200 cm AiM CAN cable X08KPK6OC200
- Keypad K6 Bula + 400 cm AiM CAN cable X08KPK6OC400
- Keypad K8 Bula
- Keypad K6+ 200 cm AiM CAN cable X08KPK8OC200
- Keypad K6+ 400 cm AiM CAN cable X08KPK8OC400
- Keypad K15 Bula
- Keypad K15 Bula + 200 cm AiM CAN cable X08KPK15OC200
- Keypad K15 Bula + 400 cm AiM CAN cable X08KPK15OC400
- Li-Keypads tsohle tse bulehileng li tla le thapo ea Open CAN e sebelisoang ho e hokahanya le sesebelisoa se seholo empa lithapo le tsona li ka rekoa ka thoko e le likarolo tse ling. Linomoro tse amanang le karolo ke:
- 200 cm e bulehileng CAN cable V02551770
- 400 cm e bulehileng CAN cable V02551780
Mefuta eohle e bulehileng ea Keypad le eona e ka hokeloa ho thapo ea AiM e bulehileng ea CAN e ka rekoang ka thoko joalo ka boikhethelo. Linomoro tse amanang le karolo ke: - 200 cm e bulehileng mohala oa AiM CAN V02551850
- 400 cm e bulehileng mohala oa AiM CAN V02551860
Ho hokela mofuta o butsoeng oa Keypad ho PC ho hlokahala thapo e nepahetseng ea USB. Linomoro tse amanang le karolo ke: - 30 cm thapo ea USB V02551690
- 50 cm thapo ea USB + 12V matla a V02551960
- Likonopo tsa litšoantšo:
- 72 likotoana letšoao la X08KPK8KICONS
- lets'oao le le leng tlanya mona ho tseba nomoro ea karolo ka 'ngoe ea setšoantšo
Tlhophiso ea software
Bakeng sa ho hlophisa Keypad, khoasolla software ea RaceStudio3 ho tsoa ho AiM website at aim-sportline.com Software/firmware download sebaka: AiM – Software/Firmware download (aim-sportline.com)
Ha software e se e kentsoe, e tsamaise 'me u latele mehato ena:
- Kenya Configuration Menu u tobetsa aekhone e totobalitsoeng ka tlase:
tobetsa konopo ea "Ncha" (1) ho toolbar e kaholimo ho le letona- tsamaisetsa phanele e khothalelitsoeng, khetha konopo e lakatsehang ea Open (2)
- tobetsa "OK" (3)
U hloka ho lokisa:
- Likonopo
- E KA Kenya Protocol
- E KA hlahisa melaetsa
Litlhophiso tsa li-pushbuttons
Lintlha tse ling tse potlakileng pele re qala ho sekaseka mokhoa oa ho hlophisa Keypad:
- maemo a pushbutton a ka beoa joalo ka Momentary, Toggle kapa Multi-status joalo ka ha ho hlalositsoe serapeng sa 3.1.1; hape hoa khoneha ho beha moeli oa nako ho laola likhatello tsa konopo tse khutšoanyane le tse telele ka litsela tse fapaneng
- boemo ba pushbutton bo ka fetisoa ka CAN ka maqhubu a tsitsitseng le / kapa ha e fetoha
- boemo ba konopo e 'ngoe le e' ngoe ka matla OFF e ka tsosolosoa ka matla a latelang ON
- konopo e 'ngoe le e' ngoe e ka etsoa - e tiileng kapa ea panya - ka mebala e 8 e fapaneng joalo ka ha ho hlalositsoe serapeng sa 3.1.2
- Open Keypads e ka laola protocol ea CAN INPUT molemong oa ho fana ka maikutlo ka 'mala oa li-LED, ho ipapisitse le tlhaiso-leseling eo e e fumanang.
Litlhophiso tsa boemo ba li-pushbuttons
U ka beha mekhoa e fapaneng bakeng sa konopo e 'ngoe le e' ngoe:
NAKO: boemo ke:
- ON ha pushbutton e sutumetsoa
- TLOA ha konopo ea pushe e lokolloa
Ka kopo hlokomela: maemo a mabeli a ON le OFF a ka amahanngoa ka bolokolohi le boleng ba linomoro
Ka kopo Tlhokomeliso: ho beha konopo ea Puseletso feela e le Nakoana o ka hokahanya taelo e latelang ho konopo e 'ngoe le e' ngoe: Taelo ea "Sesebelisoa se Khanyang"
- Nyollelo
- Fokotsa
TLHOKOMELISO: boemo ke:
- ON ha konopo e sutumetsoa hang, 'me e lula e ON ho fihlela ha e sutumetsoa hape
- TLOA ha konopo e sutumetsoa lekhetlo la bobeli
Boemo ka bobeli ON le OFF bo ka amahanngoa ka bolokolohi le boleng ba linomoro.
MALTI-STATUS: boemo bo ka 'na ba nka litekanyetso tse fapaneng tse fetohang nako le nako ha pushbutton e sutumetsoa. Litlhophiso tsena li na le thuso, mohlalaample, ho khetha e 'ngoe har'a limmapa tse fapaneng kapa ho beha maemo a fapaneng a ho emisa jj.
Ho sa tsotellehe hore na pushbutton e behiloe joang, u ka boela ua beha moeli oa nako: tabeng ena, konopo ea pushbutton e behiloe ho litekanyetso tse peli tse fapaneng tseo u ka li hlalosang, ho itšetlehile ka hore na u e sutumelletsa nako e kae.
Ho etsa joalo, lumella "sebelisa nako" lebokose la ho hlahloba lebokoseng le ka holimo la liphanele tsa litlhophiso. Tabeng ena, pushbutton e behiloe ho litekanyetso tse peli tse fapaneng tseo u ka li hlalosang ho latela hore na u li sutumelletsa nako e kae. 
Tokiso ea 'mala oa Pushbutton
Konopo e 'ngoe le e' ngoe e ka hlophisoa ka mebala e fapaneng ho bontša ketso e entsoeng ke mokhanni le maikutlo a ketso eo: konopo e ka fetoloa - bakeng sa ex.ample – ho panya (ho butle kapa ho potlakile) BONTŠOA ho bonts’a hore konope e sutumelitsoe, ‘me e tiileng E TŠEBELEHA ha ketso e etsoa.
CAN lipuisano
Hoa khoneha ho lokisa melaetsa ea CAN Output, e sebelisetsoang ho fetisa boemo ba li-pushbuttons, hammoho le melaetsa ea CAN Input, e sebelisetsoang ho amohela maikutlo a tsoang tšimong ho kenya li-tab tse amanang tse bontšitsoeng mona ka tlase.
E KA Kenya tlhophiso ea melaetsa
Protocol ea ho kenya ea CAN e batla e rarahane ho feta ho e laola: Keypad e tlameha ho hokahanngoa le marang-rang a CAN moo lisebelisoa tse ngata li arolelanang boemo le likanale tsa tsona. Lintlha tsena li ka baloa ho fa mokhanni boemo bo nepahetseng ba sesebelisoa seo konopo ea pushbutton e amanang le eona e le hore a e sebelise. Ho bala melaetsa ea CAN, u ka khetha protocol e nepahetseng haeba e fumaneha lethathamong la protocol. Haeba protocol e hlokahalang e sa kenyelelitsoe ho ka khoneha ho lokisa protocol ea tloaelo ho sebelisa CAN Driver Builder. Ka kopo sheba litokomane tse nepahetseng tseo u li fumanang sehokelong sena bakeng sa tlhaiso-leseling e batsi.
CAN Output melaetsa tlhophiso
Bula Letlapa la Dikonopo le ka romela melaetsa yohle e amehang mme molaetsa o mong le o mong o ka fetiswa ka makgetlo a tsitsitseng kapa neng kapa neng ha ho na le phetoho dikarolong tse fetisoang. U ka khona, mohlalaample, fetisa molaetsa nako le nako ha konopo ea pushe fetola boemo le/kapa motsotsoana o mong le o mong. 
Ka kopo, sheba tokomane e latelang bakeng sa lintlha tsa CAN Molaetsa: FAQ_RS3_CAN-Output_100_eng.pdf (aim-sportline.com)
Metako ea tekheniki
Litšoantšo tse latelang li bonts'a li-keypad le boholo ba likhoele le pinout- Keypad e bula litekanyo tsa K6 ka mm [inchi]
Letlapa la konopo bula K6 pinout
Boholo ba Keypad K8 ka mm [inchi]:
Keypad K8 pinout:
Boholo ba Keypad K15 ka mm [inchi]:
Keypad K15 pinout:
E KA Bula Cable pinout:
Tlhaloso ea Cable ea USB:
Litokomane / Lisebelisoa
 |
AiM K6 Bula Keypad Open Version [pdf] Bukana ea Mosebelisi K6 Bula, K8 Bula, K15 Bula, K6 Bula Keypad Open Version, K6 Bula, Keypad Open Version, Open Version, Version |
