AiM K6 Vhura Keypad Vhura Shanduro
Zvinotsanangurwa
- Mabhatani: K6 Vhura (6 programmable), K8 Vhura (8 programmable), K15 Vhura (15 programmable)
- Backlight: RGB ine Dimming sarudzo
- Kubatanidza: USB kuburikidza ne7 pini Binder 712 yechikadzi connector
- Muviri Material: Rubber silicon uye yakasimbiswa PA6 GS30%
- Dimensions:
- K6 Vhura: 97.4x71x24mm
- K8 Vhura: 127.4×71.4x24mm
- K15 Vhura: 157.4×104.4x24mm
- Kurema
- K6 Vhura: 120g
- K8 Vhura: 150g
- K15 Vhura: 250g
- Isingapindi mvura: IP67
Mirayiridzo Yekushandiswa Kwechigadzirwa
Kugadzirisa Keypad:
Dhawunirodha RaceStudio3 software kubva kuAiM website pa aim-sportline.com Software/firmware yekurodha nzvimbo. Isa software uye tevera matanho aya:
Kuisa Pushbutton Modes:
Iwe unogona kuseta akasiyana modes kune yega push bhatani:
- MUNHU WEKUPEDZISIRA: Inosanganisa murairo kune yega yega bhatani senge Chishandiso Brightness command.
- MULTI-STATUS: Inobvumira bhatani kuti ritore hunhu hwakasiyana hunochinja pese painosundirwa.
Kugadzirisa Nguva Yenguva:
Zvisinei ne modhi, unogona kuseta chikumbaridzo chenguva uko pushbutton inogadzikwa pamhando mbiri dzakasiyana zvichienderana nekuti inosundirwa nguva yakareba sei. Ita kuti bhokisi rekutarisa rekushandisa rigadzirise chimiro ichi.
Kugadzirisa CAN Inobuda Meseji:
Iwe unogona kugadzirisa iyo CAN Output mameseji ekutumira mabhatani ematatu uye iyo CAN Input meseji yekugamuchira mhinduro kubva kumunda. Pinda ma tabo ane hukama kuti uise izvi.
Kutumira Mharidzo:
Iyo Vhura Keypad inogona kutumira mameseji akakodzera pane yakatarwa frequency kana chero paine shanduko muminda inofambiswa. Gadzirisa mafambiro ekutumira meseji sezvinodiwa.
FAQ
Mubvunzo: Ndingawane kupi rumwe ruzivo nezve CAN Messages?
A: Ndokumbira utarise kune rinotevera gwaro kune CAN Message ruzivo: CAN MessageFAQ
Nhanganyaya
AiM Keypad Vhura Version ndiyo hutsva hutsva hwemakompakiti ekuwedzera kwakavakirwa paCAN bhazi. Inowanikwa mumavhezheni akasiyana zvichienderana nehuwandu hwemabhatani ane chimiro chinofambiswa kuburikidza neCAN bhazi. Ose mabhatani uye CAN mameseji anogadziriswa zvizere kuburikidza ne USB yekubatanidza uchishandisa AiM RaceStudio 3 Software.
Bhatani rega rega rinogona kusetwa se:
- Nenguva pfupi: iyo pushbutton chimiro ARI ON kana bhatani rinosundirwa
- Toggle: iyo pushbutton chimiro chinoshanduka kubva pa ON kuenda ku OFF pese painosundirwa bhatani
- Multistate: iyo pushbutton kukosha inoshanduka kubva pa0 kuenda kune max kukosha pese painosundirwa bhatani.
Uyezve, unogona kutsanangura chikumbaridzo chenguva chebhatani rega rega rinotsanangura maitiro akasiyana kana SHORT kana LONG compression chiitiko chaonekwa.
Bhatani rega rega rinogona kugadzirwa mune rumwe ruvara kana yakasimba, inononoka kana kukurumidza kubwaira modhi.
Izvo zvakare zvinogoneka kutsanangura CAN INPUT protocol kubvumidza iyo LED ruvara kwete chete kubvuma bhatani compression chiitiko, asi zvakare kuratidza chimiro chechishandiso.
Chekupedzisira, zvinogoneka kugadzirisa bhatani rekuwedzera kana kuderedza kupenya kweyero yekiyi.
| K6 Vhura | K8 Vhura | K15 Vhura | |
| Mabhatani | 6 programmable | 8 programmable | 15 programmable |
| Backlight | RGB ine Dimming sarudzo | ||
| Connection | USB kuburikidza ne7 mapini Binder 712 munhukadzi connector | ||
| Body Material | Rubber silicon uye yakasimbiswa PA6 GS30% | ||
| Dimensions | 97.4x71x4x24mm | 127.4×71.4×24 | 157.4×104.4×24 |
| Kurema | 120g | 150g | 250g |
| Isingapindi mvura | IP67 | ||
Makitsi anowanikwa sarudzo uye maspare parts
Keypad yakavhurika vhezheni makiti aripo ndeaya:
- Keypad K6 Vhura
- Keypad K6 Vhura + 200 masendimita AiM CAN tambo X08KPK6OC200
- Keypad K6 Vhura + 400 masendimita AiM CAN tambo X08KPK6OC400
- Keypad K8 Vhura
- Keypad K6+ 200 masendimita AiM CAN tambo X08KPK8OC200
- Keypad K6+ 400 masendimita AiM CAN tambo X08KPK8OC400
- Keypad K15 Vhura
- Keypad K15 Vhura + 200 masendimita AiM CAN tambo X08KPK15OC200
- Keypad K15 Vhura + 400 masendimita AiM CAN tambo X08KPK15OC400
- Ese maKeyipadhi akavhurika vhezheni anouya neOvhura CAN tambo inoshandiswa kuibatanidza kune tenzi mudziyo asi tambo dzinogona kutengwawo dzakasiyana sezvisara. Nhamba dzechikamu dzakabatana ndeidzi:
- 200 masendimita akavhura CAN tambo V02551770
- 400 masendimita akavhura CAN tambo V02551780
Ese maKeyipadhi akavhurika vhezheni anogona zvakare kubatana kune AiM yakavhurika CAN tambo inogona kutengwa zvakasiyana seyakasarudzika. Nhamba dzechikamu dzakabatana ndeidzi: - 200 masendimita akavhura AiM CAN tambo V02551850
- 400 masendimita akavhura AiM CAN tambo V02551860
Kuti ubatanidze Keypad yakavhurika vhezheni kuPC yakakodzera sarudzo USB tambo inodiwa. Nhamba dzechikamu dzakabatana ndeidzi: - 30 masendimita USB tambo V02551690
- 50 masendimita USB tambo+12V simba V02551960
- Mabhatani icons:
- 72 zvidimbu icon kit X08KPK8KICONS
- single icon tinya apa kuti uzive imwe neimwe icon chikamu nhamba
Software yekugadzirisa
Nekugadzirisa iyo Keypad, dhawunirodha RaceStudio3 software kubva kuAiM website pa aim-sportline.com Software/firmware yekurodha nzvimbo: AiM – Software/Firmware download (aim-sportline.com)
Kana iyo software yaiswa, mhanyisa uye tevera matanho aya:
- Pinda Configuration Menu uchidzvanya chiratidzo chakaratidzwa pazasi:
dzvanya bhatani rekuti “Nyowani” (1) kumusoro kurudyi bhatani rekushandisa- penya pani inokurudzirwa, sarudza yaunoda Keypad Vhura (2)
- dzvanya "OK" (3)
Iwe unofanirwa kugadzirira:
- Mabhatani
- CAN Input protocol
- CAN Kuburitsa mameseji
Pushbuttons kugadzirisa
Mamwe manotsi anokurumidza tisati tatanga kuongorora maitiro ekugadzirisa Keypad:
- chimiro chepushbutton chinogona kuiswa seMomentary, Toggle kana Multi-status sezvakatsanangurwa mundima 3.1.1; zvinokwanisikawo kuseta chikumbaridzo chenguva kubata mapfupi uye marefu mabhatani mabhatani nenzira dzakasiyana
- iyo pushbutton mamiriro anogona kutapurirana kuburikidza neCAN pane yakatarwa frequency uye / kana painochinja
- mamiriro ega ega pushbutton pamagetsi OFF anogona kudzoserwa pamagetsi anotevera ON
- bhatani rega rega rinogona kugadzirwa - rakasimba kana kubwaira - mune 8 mavara akasiyana sekutsanangurwa kwazvino mundima 3.1.2
- yakavhurika Keypads inogona kubata CAN INPUT protocol kuitira kuti ipe mhinduro kuburikidza ne LEDs ruvara, zvichienderana neruzivo rwainogamuchira.
Pushbuttons mamiriro ekugadzirisa
Iwe unogona kuseta akasiyana modes kune yega pushbutton:
NGUVA: chimiro ndeichi:
- ON apo pushbutton inosundirwa
- BIMA kana bhatani raburitswa
Ndapota chiziviso: ese ari maviri mamiriro ON uye OFF anogona kubatanidzwa zvakasununguka nehuwandu hwenhamba
Ndapota chiziviso: kungoisa bhatani bhatani seMomentary unogona kubatanidza murairo unotevera kune imwe neimwe pushbutton: "Chishandiso Kupenya" kuraira
- Wedzera
- Decrease
TOGLE: chimiro ndeichi:
- PANE kana bhatani rikasundirwa kamwe chete, uye rinoramba IRI PANE kusvika riinhi rasundirwa zvakare
- BIMA kana bhatani rikasundirwa kechipiri
Zvose zviri zviviri ON uye OFF zvinogona kushamwaridzana zvakasununguka nehuwandu hwenhamba.
MULTI-STATUS: chimiro chinogona kutora hunhu hwakasiyana hunochinja pese painosundirwa bhatani. Kuseta uku kunobatsira, semuenzanisoample, kusarudza imwe pakati pemepu dzakasiyana kana kuseta mazinga akasiyana ekumiswa nezvimwe.
Hazvina mhosva kuti iyo pushbutton yakaiswa sei iwe unogona zvakare kuseta nguva chikumbaridzo: mune iyi nyaya, iyo pushbutton inoiswa pamhando mbiri dzakasiyana dzaungatsanangure, zvichienderana nekuti waunosundidzira kwenguva yakareba sei.
Kuti uite kudaro, gonesa "shandisa nguva" cheki bhokisi riri pamusoro pebhokisi rezvirongwa zvekuseta. Muchiitiko ichi, bhatani rinoiswa pamhando mbiri dzakasiyana dzaungatsanangure zvichienderana nekureba kwaunoisundira. 
Pushbutton color configuration
Bhatani rega rega rinogona kuiswa nemavara akasiyana kuratidza chiitiko chakaitwa nemutyairi uye mhinduro yechiito ichocho: bhatani rinogona kushandurwa - rekare.ample – blinking (inononoka kana kukurumidza) GREEN kuratidza kuti pushbutton yasundirwa, uye yakasimba GREEN kana chiito chaitwa.
CAN kutaurirana
Zvinogoneka kugadzirisa CAN Output mameseji, anoshandiswa kuendesa chimiro chemabhatani, pamwe neCAN Input meseji, inoshandiswa kugamuchira mhinduro kubva kumunda ichipinda matabo ane hukama anoratidzwa pano pazasi.
CAN Kupinza mameseji gadziriro
Iyo CAN yekupinza protocol yakanyanya kuoma kubata: iyo Keypad inofanirwa kuve yakabatana kune CAN network uko mamwe maturusi anogovera mamiriro avo nematashi. Ruzivo urwu runogona kuverengerwa kupa mutyairi mamiriro chaiwo echishandiso icho pushbutton chine hukama nacho kuitira kuti chishandise. Kuti uverenge iyo CAN mameseji, unogona kusarudza yakakodzera protocol kana iripo mune protocol runyorwa. Kana iyo protocol inodiwa isingabatanidzwe zvinokwanisika kugadzirisa tsika protocol uchishandisa CAN Driver Builder. Ndokumbira utarise kune akakodzera magwaro aunowana pane ino link kuti uwane rumwe ruzivo.
CAN Kuburitsa mameseji kugadzirisa
Vhura Keypad inogona kutumira mameseji ese akakodzera uye meseji yega yega inogona kufambiswa pane yakatarwa frequency kana pese paine shanduko muminda inofambiswa. Unogona, semuenzanisoample, tumira meseji pese pese bhatani rinochinja chimiro uye/kana sekondi yega yega. 
Tapota tarisai gwaro rinotevera reruzivo rweMharidzo yeCAN: FAQ_RS3_CAN-Output_100_eng.pdf (aim-sportline.com)
Technical vanodhirowa
Iyi inotevera mifananidzo inoratidza keypad uye tambo zviyero uye pinout- Keypad yakavhura K6 zviyero mumm [inches]
Keypad vhura K6 pinout
Keypad K8 zviyero mu mm [inches]:
Keypad K8 pinout:
Keypad K15 zviyero mu mm [inches]:
Keypad K15 pinout:
KUNOGONA KUvhura Cable pinout:
USB Cable pinout:
Zvinyorwa / Zvishandiso
 |
AiM K6 Vhura Keypad Vhura Shanduro [pdf] Bhuku reMushandisi K6 Vhura, K8 Vhura, K15 Vhura, K6 Vhura Keypad Vhura Shanduro, K6 Vhura, Keypad Vhura Shanduro, Vhura Shanduro, Shanduro |
