• Inowanikwa mu6 uye 9 chiteshi zvigadziriso
• Toroidal yakakwirira simba shanduko yakayerwa kusvika 1.25AMP (30VA)
• 3 zvirongwa, imwe neimwe iine 4 nguva dzekutanga, yakawanda yegumi nemaviri ekutanga nguva pazuva
• Chiteshi chinomhanya nguva kubva paminiti 1 kusvika maawa gumi nemaviri nemaminitsi makumi mashanu nemapfumbamwe
• Sarudzo dzekudiridza dzinosarudzika: Kusarudzika kwemazuva manomwe, Kunyange, Odd, Odd -7, kusarudzwa kwezuva rekudiridza kubva zuva rega rega kusvika kune rimwe nerimwe rechigumi nemashanu.
• Kudiridza bhajeti ficha inobvumira kugadziridzwa kwechiteshi kumhanyisa nguva nezanatage, kubva OFF kusvika 200%, nemwedzi
• Mvura inopinza sensor yekudzima zviteshi panguva yekunyorova
• Permanent memory feature inochengetedza otomatiki zvirongwa panguva yekutadza kwemagetsi
• Manual mabasa echirongwa uye chiteshi mashandiro
• Pombi inobuda kutyaira 24VAC coil
• Wachi chaiyo-nguva inotsigirwa ne3V Lithium bhatiri
• Contractor recall feature

Mirayiridzo Yekushandiswa Kwechigadzirwa

Yakarurama Power-up Procedure

1. Batanidza controller kune AC simba.
2. Isa bhatiri re9V kuti uwedzere hupenyu hwebhatiri remari.

ProgrammingSeta otomatiki Chirongwa:

Manual OperationKuita chiteshi chimwe chete:

FAQs

Ndingaisa sei mazuva ekudiridza?Kuti uise mazuva ekudiridza, enda kune chikamu chepurogiramu uye sarudza sarudzo yemazuva ekudiridza. Sarudza kubva pane zvingasarudzwa senge Yega 7 zuva sarudzo, Kunyange, Odd, nezvimwe, zvichibva pane zvaunoda.

Iyo sensor yemvura inoshanda sei?Iyo inonaya sensor yekupinda inodzima otomatiki zviteshi zvese kana zviteshi zvakasarudzwa kana yaona mamiriro emvura. Ita shuwa kuti sensor yekunaya yakamisikidzwa uye yakabatana nemazvo kuti chinhu ichi chishande.

Nhanganyaya

• Yako PRO469 Multi-Program Irrigation Controller inowanikwa mu6 uye 9 zviteshi zvigadziriso.
• Yakagadzirwa kuti ivhare huwandu hwakasiyana hwekushandisa kubva pakugara uye yekutengesa turf, kune yakareruka zvekurima, uye nyanzvi nursery.
• Uyu mutongi ane anobvira matatu akaparadzana mapurogiramu anosvika gumi nemaviri anotanga pazuva. Mutongi ane chirongwa chekudiridza chemazuva manomwe nesarudzo yezuva rega rega pachirongwa kana 3 kalendari yekudiridza isinganzwisisike / kunyangwe yezuva kana masheji ekudiridza anosarudzwa kubva zuva rega rega kusvika kumazuva gumi nemashanu ega ega. Nhepfenyuro yega yega inogona kugoverwa kune imwe kana mapurogiramu ese uye inogona kuva nenguva yekumhanya yeminiti 12 kusvika 7 maawa 365 maminetsi kana maawa makumi maviri nemashanu kana bhajeti remvura rakaiswa ku15%. Iye zvino ne "Water Smart Seasonal Set" iyo inobvumira iyo otomatiki yekumhanyisa nguva kuti igadziriswe muchikamutage kubva "OFF" kusvika ku200% pamwedzi.
• Tagara tine hanya nekushandiswa kwemvura kwakasimba. Mutongi ane zvinhu zvakawanda zvekuchengetedza mvura zvinogona kushandiswa kuchengetedza yepamusoro-soro yemhando yemiti ine huwandu hushoma hwekushandisa mvura. Iyo yakasanganiswa bhajeti nzvimbo inobvumira shanduko yepasi rose yenguva dzekumhanya pasina kukanganisa akarongwa nguva dzekumhanya. Izvi zvinobvumira kudzikira kwese kushandiswa kwemvura pamazuva ekushomeka kwemvura.

Yakarurama Power-up Procedure

1. Batanidza kune AC Power
2. Isa bhatiri re9V kuti uwedzere hupenyu hwebhatiri remari
   Mabhatiri achachengetedza wachi

Features

• 6 uye 9 chiteshi modhi
• Toroidal yakakwirira simba shanduko yakayerwa kusvika 1.25AMP (30VA)
• Modhi yekunze ine inbuilt transformer inosanganisira lead uye plug, yeAustralia
• Zvirongwa zvitatu, chimwe nechimwe chine nguva dzekutanga 3, dzinosvika gumi nembiri dzekutanga pazuva
• Chiteshi chinomhanya nguva kubva paminiti 1 kusvika maawa gumi nemaviri nemaminitsi makumi mashanu nemapfumbamwe
• Sarudzo dzekudiridza dzinosarudzika: Kusarudzika kwemazuva manomwe, Kunyange, Odd, Odd -7, kusarudzwa kwezuva rekudiridza kubva zuva rega rega kusvika kune rimwe nerimwe rechigumi nemashanu.
• Kudiridza bhajeti ficha inobvumira kukurumidza kugadzirisa kwechiteshi kumhanyisa nguva nezanatage, kubva OFF kusvika 200%, nemwedzi
• Mvura inopinza sensor inodzima zviteshi zvese kana zviteshi zvakasarudzwa panguva yekunaya, kana sensor yakaiswa
• Permanent memory feature inochengetedza otomatiki zvirongwa panguva yekutadza kwemagetsi
• Manual mabasa: mhanyisa chirongwa kana boka rezvirongwa kamwe chete, mhanyisa chiteshi chimwe chete, ine bvunzo kutenderera kune ese zviteshi, OFF chinzvimbo chekumisa kutenderera kwekudiridza kana kumisa otomatiki zvirongwa munguva yechando.
• Pombi inobuda kutyaira 24VAC coil L Chaiyo-nguva wachi inotsigirwa ne3V
• Lithium bhatiri (yakagadzirirwa kare)
• Contractor recall feature

Overview

Programming

Mutongi uyu akagadzirwa aine zvirongwa zvishanu zvakasiyana kuti zvibvumire nzvimbo dzakasiyana siyana kuti dzive neyadzo yekudiridza yega
PROGRAM inzira yekuunganidza zviteshi (mavharuvhu) ane zvinodiwa zvekudiridza zvakafanana kumvura pamazuva mamwe chete. Zviteshi izvi zvinodiridza mukutevedzana uye nemazuva akasarudzwa.

• Rongedza zviteshi (mavharuvhu) ari kudiridza nzvimbo dzakafanana dzenzvimbo pamwechete. For example, turf, mibhedha yemaruva, magadheni-aya mapoka akasiyana anogona kuda zvirongwa zvekudiridza ega ega, kana maPROGRAMS
• Seta nguva iripo uye zuva rakakodzera revhiki. Kana kusanzwisisika kana kunyange zuva kudiridza kuchizoshandiswa, ita shuwa kuti gore razvino, mwedzi uye zuva remwedzi rakarurama.
• Kuti usarudze imwe PROGRAM, tinya . Imwe neimwe press ichaenda kune inotevera PROGRAM nhamba. Izvi zvinobatsira kukurumidza reviewing yeruzivo rwakambopinda pasina kurasikirwa nenzvimbo yako muchirongwa chechirongwa

Seta otomatiki Chirongwa

Seta otomatiki PROGRAM yeboka rega rega rezviteshi (mavharuvhu) nekuzadzisa matanho matatu anotevera:

1. Seta kudiridza START TIMES
   Kwenguva yega yega yekutanga, zviteshi zvese (mavharuvhu) zvakasarudzirwa PROGRAM zvinouya mukutevedzana. Kana nguva mbiri dzekutanga dzaiswa, zviteshi (mavharuvhu) achauya kaviri
2. Isa MAZUVA EMVURA
3. Seta nguva dzeRUN TIME

Iyi controller yakagadzirirwa kukurumidza intuitive programming. Rangarira aya matipi akareruka ekunetsa pasina hurongwa:

• Kudzvanya kumwe chete kwebhatani kuchawedzera imwe unit
• Kubata bhatani pasi kuchakurumidza kufamba nemayunitsi Panguva yechirongwa, mayuniti anopenya chete anokwanisa kusetwa.
• Gadzirisa mayunitsi anopenya uchishandisa
• Press kupuruzira mumasettings sezvaunoda
• Iyo MAIN DIAL ndiyo yekutanga mudziyo wekusarudza oparesheni
• Press kusarudza maPROGRAMS akasiyana. Imwe neimwe push pabhatani iri ichawedzera imwe PROGRAM nhamba

Seta Nguva Yazvino, Zuva uye Zuva

1. Shandura nhare kuti DATE+TIME
2. Shandisa kugadzirisa maminitsi anopenya
3. Press wobva washandisa kugadzirisa maawa anopenya AM/PM inofanira kusetwa nemazvo.
4. Press wobva washandisa kugadzirisa mazuva anopenya evhiki
5. Press kakawanda kusvikira zuva rekarenda raonekwa pachiratidziro negore richipenya
   Iyo kalendari inongoda kusetwa kana uchisarudza odd / kunyangwe zuva kudiridza
6. Shandisa kugadzirisa gore
7. Press wobva washandisa kugadzirisa mwedzi unopenya
8. Press wobva washandisa kugadzirisa zuva rekupenya
   Kuti udzoke kuwachi, dzosera dhivhi kuAUTO

Seta Nguva dzekutanga

Yese zviteshi zvinomhanya mukutevedzana kwenguva yega yega yekutanga
Zve example, tichaseta NGUVA YOKUTANGA yePROG Nha

1. Shandura nhare kuti START TIMES uye uone kuti PROG Nhamba 1 iri kuratidza
   Kana zvisina kudaro, dzvanya kutenderera nemaPROGRAMS uye sarudza PROG Nha
2. KUTANGA Kwete. ichange ichipenya
3. Shandisa kuchinja START Nha. kana zvichidiwa
4. Press uye maawa ekutanga Nha
5. Shandisa kugadzirisa kana zvichidiwa
   Ita shuwa kuti AM/PM ndeyechokwadi
6. Press uye maminetsi achapenya
7. Shandisa kugadzirisa kana zvichidiwa
   Imwe neimwe PROGRAM inogona kuva ne4 START TIMES
8.  Kuseta imwe START TIME, dzvanya uye KUTANGA Nha. 1 ichapenya
9. Famba mberi kuTANGA Nhamba 2 nekudzvanya
10. Tevedzera nhanho 4-7 pamusoro kuti uise NGUVA YOKUTANGA yeTANGA Nha
    Kugonesa kana kudzima NGUVA YOKUTANGA, shandisa kana kuseta ese maawa nemaminitsi kusvika zero
    Kutenderera nekuchinja maPROGRAMS, tinya kakawanda
    Isa Mazuva Ekudiridza
    Ichi chikamu chine zuva rega rega, EVEN/ODD zuva, ODD-31 zuva uye INTERVAL DAYS sarudzo
    Individual Day Sarudzo:
    Tendeuka kudhaira kuWATER DAYS uye PROG No. 1 icharatidza
11. Kana zvisina kudaro, shandisa kusarudza PROG Nhamba 1
12. MON (Muvhuro) ichange ichipenya
13. Shandisa kugonesa kana kudzima kudiridza kweMuvhuro zvakateerana
14. Shandisa kutenderera nemazuva evhiki
    Mazuva anoshanda acharatidzwa ne pasi
    ODD/EVEN Zuva Sarudzo
    Mamwe matunhu anongobvumira kudiridza pamazuva asinganzwisisike kana nhamba yemba isinganzwisisike, kana zvimwe chetezvo kune chero mazuva
    Tendeuka kudhaira kuWATER DAYS uye PROG No. 1 icharatidza
15. Press kasingaperi kutenderera yapfuura FRI kusvika ODD DAYS kana EVEN DAYS iri kuratidza zvinoenderana
    Press zvakare yeODD-31 kana zvichidikanwa
    Karenda yemazuva makumi matatu nenhanhatu inofanira kurongerwa nenzira kwayo pachinhu ichi, (ona Set Current Time, Day and Date)
    Uyu controller anotora makore akawanda achifunga

Interval Day Selection

1. Tendeuka kudhaira kuWATER DAYS uye PROG No. 1 icharatidza
2. Press kasingaperi kutenderera yapfuura FRI kusvika INTERVAL DAYS iri kuratidza zvinoenderana
   INTERVAL DAYS 1 ichange ichipenya
   Shandisa kusarudza kubva 1 kusvika 15 zuva intervals
   Example: INTERVAL DAYS 2 zvinoreva kuti mutongi achamhanyisa chirongwa mumazuva maviri
   Zuva rinotevera rinoshanda rinogara richishandurwa kuita 1, zvichireva kuti mangwana ndiro zuva rekutanga rinoshanda kumhanya

Seta Nguva dzekumhanya

• Uhwu ndihwo hurefu hwenguva iyo chiteshi chega chega (vharuvhu) yakarongerwa kudiridza pane imwe chirongwa
• Nguva yakakura yekudiridza maawa gumi nemaviri 12 maminetsi pachiteshi chimwe nechimwe
• Chiteshi chinogona kupihwa kune chero kana ese anobvira matatu mapurogiramu

1. Shandura nhare kuti RUN TIMES

   
   STATION Nhamba 1 ichange ichipenya yakanyorwa kuti OFF, sezvaratidzwa pamusoro, zvichireva kuti haina RUN TIME yakarongwa mairi.
   Iyo controller ine ndangariro yekusingaperi saka kana paine kutadza kwesimba, kunyangwe bhatiri risina kuiswa, iyo yakarongwa tsika inodzoserwa kune iyo unit.
2. Press kusarudza chiteshi (vharuvhu) nhamba
3. Press uye OFF ichapenya
4. Press kugadzirisa iyo RUN TIME maminetsi sezvaunoda
5. Press uye nguva yeRUN TIME ichapenya
6. Press kugadzirisa maawa eRUN TIME sezvaunoda
7. Dzvanya uye STATION Nha. ichapenya zvakare
8. Dzvanya kana kusarudza imwe chiteshi (vharuvhu), uye dzokorora nhanho 2-7 pamusoro kuseta NGUVA YEMHANYA
   Kuti udzime chiteshi, isa zvese maawa nemaminetsi kuti 0, uye chiratidziro chichapenya OFF sezvaratidzwa pamusoro
   Izvi zvinopedzisa nzira yekuseta yePROG Nha
   Seta Zvimwe Zvirongwa
   Seta zvirongwa zvekusvika ku6 PROGRAMS nekudzvanya pakumisikidza NGUVA ZVOKUTANGA, MAZUVA ekudiridza uye NGUVA dzeMHANYA sezvakambotaurwa
   Kunyangwe iyo controller ichimhanyisa otomatiki zvirongwa neiyo MAIN DIAL mune chero chinzvimbo (kunze kwe OFF), isu tinokurudzira kusiya iyo huru dial pane AUTO chinzvimbo kana isiri kuronga kana kushanda nemaoko.

Manual Operation

Mhanyai Single Station

® Nguva yakawanda yekumhanya i12 maawa 59 maminitsi

1. Shandura nhare kuRUN STATION
   STATION Nhamba 1 ichange ichipenya
   The default manual run time maminetsi gumi-kugadzirisa izvi, ona Rongedza Default Manual Run Time pazasi.
2. Shandisa kusarudza chiteshi chaunoda
   Chiteshi chakasarudzwa chinotanga kushanda uye RUN TIME ichadzikira zvinoenderana
   Kana paine pombi kana master valve yakabatana,
   PUMP A icharatidzwa muchiratidziro, zvichiratidza kuti pombi/tenzi iri kushanda
3. Press uye iyo RUN TIME maminetsi achapenya
4. Shandisa kugadzirisa maminitsi
5. Press uye nguva yeRUN TIME ichapenya
6. Shandisa kugadzirisa maawa
   Iyo unit ichadzokera kuAUTO mushure mekunge nguva yapera
   Kana ukakanganwa kudzorera dial kuAUTO, mutongi acharamba achimhanyisa zvirongwa
7. Kuti urege kudiridza nekukasika, dzima dial kuti OFF

Rongedza iyo Default Manual Run Nguva

1. Shandura nhare kuti RUN STATION STATION Nhamba 1 ichapenya
2. Press uye iyo RUN TIME maminetsi achapenya
3. Shandisa kugadzirisa iyo RUN TIME maminetsi
4. Press uye iyo yakagadzika RUN TIME maawa ichapenya
5. Shandisa kugadzirisa iyo RUN TIME maawa
6. Kana iyo yaunoda RUN TIME yaiswa, tinya kuchengetedza izvi sebhuku rekutanga RUN TIME
   Iyo itsva default ichaonekwa nguva dzose kana dial yaitwa RUN STATION

Shandisai Purogiramu

1. Kuti uite chirongwa chakazara nemaoko kana kurongedza zvirongwa zvakawanda kuti umhanye, shandura dial kuti RUN PROGRAM
   OFF ichapenya pachiratidziro
2. Kugonesa PROGRAM, tinya uye chiratidziro chichachinja kuva ON
   Kana pasina RUN TIME yakasetwa kune yaunoda PROGRAM, danho riri pamusoro harishande
   3. Kuti umhanye PROGRAM yaunoda nekukurumidza, dzvanya

Stacking Programs

• Panogona kunge paine dzimwe nguva pazvinenge zvichidikanwa kumhanyisa zvinopfuura chirongwa chimwe nemaoko
• Iyo controller inobvumira izvi kuti zviitike ichishandisa yayo yakasarudzika nzvimbo yekugonesa chirongwa, isati yaimhanyisa
• For example, kumhanyisa PROG No. 1 uye zvakare PROG Nha.

1. Tevedza nhanho 1 uye 2 yeMhanya Chirongwa kugonesa imwe PROGRAM
2. Kusarudza inotevera PROGRAM dzvanya P
3. Gonesa iyo inotevera PROGRAM nekudzvanya
   Kudzima nhamba yepurogiramu, tinya
4. Dzokorora nhanho 2-3 pamusoro kuti ugonese mamwe maPROGRAM
5. Kana ese maPROGRAM ese anodiwa agoneswa, anogona kumhanya nekudzvanya
   Iyo controller ikozvino ichamhanyisa ese maPROGRAMS akagoneswa mukutevedzana kurongeka
   Iyi nzira inogona kushandiswa kugonesa chero, kana ese ezvirongwa zviripo pane controller.
   Paunenge uchimhanyisa zvirongwa mune iyi modhi iyo BUDGET% ichachinja iyo RUN TIMES yeimwe neimwe chiteshi zvinoenderana

Zvimwe Zvimiro

Rega Kudiridza

• Kuti umise chirongwa chekudiridza otomatiki kana yemanyorero, dzima dial kuti OFF
• Kudiridza otomatiki rangarira kudzoreredza dial kuAUTO, sezvo OFF ichamisa chero mafambiro ekudiridza kubva kuitika.

Kurongedza Nguva dzekutanga

• Kana ukangoerekana waisa imwechete NGUVA pane inodarika PROGRAM imwe chete, mutongi anozozvirongedza mukutevedzana.
• Zvese zvakarongwa START TIMES zvichadiridzwa kubva kunhamba yepamusoro kutanga

Otomatiki Backup

• Ichi chigadzirwa chakabatanidzwa nekusingaperi ndangariro.
  Izvi zvinobvumira mutongi kuti abate kukosha kwese kwakachengetwa kunyangwe pasina magetsi, zvinoreva kuti ruzivo rwakarongwa haruzomborasikirwe.
• Kuisa bhatiri re9V kunokurudzirwa kuwedzera hupenyu hwebhatiri remari asi hazvizopi simba rakakwana mhanyisa chiratidziro.
• Kana bhatiri risina kuiswa, iyo chaiyo nguva wachi inotsigirwa ne lithium coin bhatiri iro rakagadzirirwa fekitori-kana simba rinodzosa wachi ichadzoserwa kunguva yazvino.
• Zvinokurudzirwa kuti bhatiri re9V rakakwana uye rinoshandurwa mwedzi gumi nemiviri yega yega
• Chiratidziro chicharatidza FAULT BAT muchiratidziro kana bhatiri rasara vhiki kuti ritange- kana izvi zvikaitika, tsiva bhatiri nekukasira.
• Kana simba re AC rakadzimwa, chiratidziro hachizoonekwe

Rain Sensor

1. Paunenge uchiisa sensor yemvura, tanga wabvisa fekitori yakasungirirwa link pakati peC uye R terminals sezvakaratidzwa

   
2. Tsiva nemawaya maviri kubva ku sensor yekunaya mune aya materminal, polarity HAIDII
3. Shandura switch yeSENSOR kuti ON
4. Shandura dial kuSENSOR kuti ugonese sensor yako yemvura kune imwe neimwe nhepfenyuro
   Iyo yekusagadzika modhi yakabatidzwa kune ese zviteshi
   Kana chiteshi chakanyorwa ON pachiratidziro, izvi zvinoreva kuti sensor yako yekunaya ichakwanisa kudzora vharuvhu panguva yekunaya kwemvura.
   Iwe unofanirwa kuve uine chiteshi chinogara chichida kudiridzwa, (senge yakavharirwa greenhouse, kana zvirimwa zviri pasi pekuvhara) sensor yemvura inogona KUDZIMWA kuti irambe ichidiridza panguva yekunaya kwemvura.
5. Kuti udzime chiteshi, tinya kutenderera nekusarudza chiteshi chaunoda, wobva wadzvanya
6. Kuti udzose chiteshi kuti ON, dzvanya
   Kudzima sensor yekunaya uye kubvumira zviteshi zvese kumvura, shandura iyo SENSOR switch kuti OFF

YAMBIRO!
CHENGA MABHATITI MATSHA KANA AKASHANDISWA

Bhatiri inogona kukonzera kukuvadzwa kwakanyanya kana kuuraya mumaawa e2 kana pasi kana ikamedzwa kana kuiswa mukati mechikamu chipi nechipi chemuviri. Kana iwe uchifunga kuti mabhatiri anogona kunge akamedzwa kana kuiswa mukati menhengo ipi neipi yemuviri, tsvaga kurapwa nekukasika

Bata neAustralia Poisons Information Center ye24/7 nekukurumidza, zano renyanzvi: 13 11 26
Tarisa kune yako nhungamiro yehurumende yemunharaunda yekuti ungarasa sei nemabhatani ebhatani / mari.

Kunonoka kwemvura

Kugadzirisa nguva ye sensor yako yemvura, mutongi uyu anoratidza RAIN DELAY kurongedza
Izvi zvinobvumira imwe nguva yekunonoka kupera mushure mekunge sensor yemvura yaoma chiteshi chisati chadiridza zvakare.

1. Shandura dial kuita SENSOR
2. Press kuti uwane iyo RAIN DELAY skrini
   Iko INTERVAL DAYS kukosha kwave kupenya
3. Shandisa kushandura nguva yekunonoka kwemvura mukuwedzera kwemaawa makumi maviri nemana panguva
   Kunonoka kukuru kwemazuva 9 kunogona kuiswa

Pump Kubatanidza
Ichi chikamu chinobvumira zviteshi kuti zvipiwe pombi
Iyo yakasarudzika chinzvimbo ndeyekuti zviteshi zvese zvakapihwa PUMP A

1. Kuti uchinje zviteshi zvega, shandura dial kuita PUMP
2. Press kutenderera nechiteshi chimwe nechimwe
3. Shandisa kuchinja PUMP A ku ON kana KUDZIMA zvakateerana

Ratidza Kusiyanisa

1. Kuti ugadzirise musiyano weLCD, shandura dial kuti PUMP
2. Press kakawanda kusvikira chiratidziro chaverenga CON
3. Shandisa kugadzirisa musiyano wekuratidzira sezvaunoda
4. Kuti uchengetedze marongero ako, dzosera nhare kuAUTO

Kuronga Kwemvura uye Kugadziriswa Kwemwaka

® Automatic station RUN TIMES inogona kugadziriswa
nehuwandutage sezvo mwaka unochinja
L Izvi zvichachengetedza mvura yakakosha seRUN TIMES
inogona kugadziriswa nokukurumidza muchirimo, chirimo, uye
matsutso kuderedza kana kuwedzera kushandiswa kwemvura
® Nokuda kwebasa iri, rinokosha
kuseta karenda nemazvo–ona
Seta Yazvino Nguva, Zuva uye Zuva kuti uwane rumwe ruzivo

1. Shandura dial kuBUDGET-chiratidziro chichaonekwa seizvi:

   Izvi zvinoreva kuti RUN TIMES yakaiswa kuBUDGET% ye100%
   Nekumisikidza, chiratidziro chicharatidza MWEDZI wazvino
   For example, kana STATION Nhamba 1 yakasetwa kuita maminetsi gumi zvino ichamhanya kwemaminetsi gumi
   Kana BUDGET% yachinja kuita 50%, STATION Nha.
   Iyo bhajeti kuverenga inoiswa kune ese anoshanda STATIONS uye RUN TIMES

2. Shandisa kutenderera mumwedzi 1 kusvika ku12
3. Shandisa kugadzirisa iyo BUDGET% mu10% increments pamwedzi wega wega
   Izvi zvinogona kusetwa kumwedzi wega wega kubva paOFF kusvika 200%
   Iyo yekusingaperi yekuyeuka basa ichachengetedza ruzivo
4. Kuti udzoke kuwachi, shandura dial kuAUTO
5. Kana iyo BUDGET% yemwedzi wako wazvino isiri zana, izvi zvicharatidzwa muAUTO wachi kuratidza.

Fault Idication Feature

• Iyi unit ine M205 1AMP girazi fuse kuchengetedza transformer kubva pakukwira kwemagetsi, uye fiyuzi yemagetsi kuchengetedza dunhu kubva kuzvikanganiso zvemunda kana vharafu.
  Zvinotevera kukanganisa zviratidzo zvinogona kuratidzwa:
  HAPANA AC: Haina kubatana kune mains simba kana transformer isiri kushanda
  FAULT BAT: 9V bhatiri haina kubatana kana inoda kutsiviwa

System Bvunzo

1. Shandura nhare kuti TEST STATIONS
   Iyo system test inozotanga yega
   Yako PRO469 inodiridza chiteshi chese zvakateerana kwemaminetsi maviri imwe neimwe
2. Press kuenda kuchiteshi chinotevera nguva yemaminetsi maviri isati yapera
   Hazvibviri kudzokera kumashure kune chiteshi chakapfuura
   Kuti utangezve kuyedza system kubva paSTATION Nha. 1, dzima dial, wodzokera kuTEST STATIONS.
   Kuchenesa Zvirongwa
   Sezvo chikamu ichi chine chisingaperi chiyeuchidzo chimiro, iyo yakanakisa nzira yekubvisa iyo PROGRAMS ndeiyi inotevera:
3. Bvisa dial kuti OFF
4.  Press kaviri kusvikira chiratidziro chaonekwa sezvizvi:

   

5. Press kubvisa maPROGRAMS ese
   Wachi ichachengetwa, uye mamwe mabasa ekuseta TIMES, WATERING DAYS uye RUN TIMES achacheneswa uye adzoserwe kumaseting ekutanga.
   MAPROGRAMS anogona zvakare kucheneswa nekuseta mawoko NGUVA, MAZUVA OKUDIRIRA uye RUN TIMES mumwe nemumwe achidzokera kune zvaakanganisa.

Chirongwa Rescue Feature

1. Kurodha Chirongwa Chekurangarira Feature shandura dial kuti OFF dzvanya uye panguva imwe chete- LOAD UP ichaonekwa pachiratidziri
2. Press kuti apedzise urongwa
   Kuisazve Chirongwa Chekurangarira Feature bvisa dial OFF wodzvanya
   LOAD ichaonekwa pachiratidziri
   Press kuti udzokere kuchirongwa chakachengetwa chepakutanga

Installation

Kuisa Controller

• Isai controller padhuze ne240VAC yekuburitsa-zvichida mumba, garaji, kana yekunze magetsi cubicle.
• Kuti zvive nyore kushanda, kuiswa kwezinga reziso kunokurudzirwa
• Zvakanaka, nzvimbo yako yekutonga haifanirwe kunaya nemvura kana nzvimbo dzinowanzoita mafashamo kana mvura inorema
• Iyi inbuilt controller inouya nemukati transformer uye inokodzera kuisirwa kunze kana mukati memukati
• Imba yacho yakagadzirirwa kuisirwa kunze asi plug inoda kuiswa mune inodzivirira mamiriro ekunze socket kana pasi pekuvhara
• Sunga mutongi uchishandisa kiyi gomba slot yakamira kunze pamusoro pepakati uye mamwe maburi akaiswa mukati mukati mechivharo chechivharo.

Electrical Hook-up

• Basa rese remagetsi rinofanirwa kuitwa zvinoenderana nemirairo iyi, uchitevera ese anoshanda emuno, nyika uye emubatanidzwa makodhi ane chekuita nenyika yekumisikidza- kutadza kuzviita kunobvisa waranti yemutongi.
• Bvisa magetsi emagetsi kusati kwaitwa chero basa rekugadzirisa kune controller kana mavharuvhu
• Usaedza kuisa waya chero yakakwira voltage zvinhu iwe pachako, kureva pombi uye macontactor epombi kana hard wiring iyo controller simba rekupa kune mains-iyi ndiyo ndima yeane rezinesi wemagetsi
• Kukuvara kwakakomba kana kufa kunogona kubva mukukochekera zvisina kufanira-kana pasina mubvunzo bvunza dare rako rinodzora kuti chii chinodiwa.

Munda Wiring Connections

1. Gadzirira waya yehoko-up nekucheka waya kusvika paurefu hwakakodzera uye kubvisa ingangoita 0.25 inches (6.0mm) yekudzivirira kubva kumagumo kuti ibatanidzwe kune controller.
2. Ita shuwa kuti terminal block screws yakasunungurwa zvakakwana kuti ibvumidze kupinda nyore kwewaya
3. Isa yakabviswa waya inopera mu clamp aperture uye simbisa screws
   Usanyanya kuomesa sezvo izvi zvinogona kukuvadza terminal block
   Kuwanda kwe0.75 amps inogona kupihwa nechero inobuda
4. Tarisa inrush ikozvino ye solenoid coils yako usati wabatanidza anopfuura maviri mavharuvhu kune chero chiteshi

Power Supply Connections

• Zvinokurudzirwa kuti transformer haina kubatana kune 240VAC yekugovera iyo zvakare kushandira kana kupa mota (senge air conditioners, pombi dzemvura, mafiriji)
• Magetsi emagetsi akakodzera semasimba emagetsi

Terminal Block Layout

1. 24VAC 24VAC magetsi ekubatanidza magetsi
2. COM Yakajairika waya yekubatanidza kune munda wiring
3. SENS Input yekunaya kwemvura
4. PUMP 1 Master valve kana pombi inotanga kubuda
5. ST1-ST9 Chiteshi (vharuvhu) zvinongedzo
   Shandisa 2 amp fuse

Kuiswa kwevhavha uye Simba reKugovera Kubatanidza

• Chinangwa chevhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhavhaivha mvura kana paine vharafu kana pasina chiteshi chiri kushanda nemazvo.
• Inoshandiswa sevhavhavha yekumashure kana kutadza kuchengetedza mudziyo uye inoiswa pakutanga kwekudiridza iyo yakabatana netambo yemvura.

Kuiswa kweStation Valve

• Anosvika maviri 24VAC solenoid mavharuvhu anogona kubatanidzwa kune yega yega chiteshi inobuda uye newaya kudzokera kuCommon (C) yekubatanidza.
• Nehurefu hwetambo refu, voltagkudonhedza kwe e kunogona kuve kwakakosha, kunyanya kana inodarika coil imwe yaiswa waya kuchiteshi
• Semutemo wakanaka wegunwe sarudza tambo yako sezvinotevera: 0–50m tambo dia 0.5mm
  • L 50-100m tambo dia 1.0mm
  • L 100-200m tambo dia 1.5mm
  • L 200-400m tambo dia 2.0mm
• Paunenge uchishandisa mavharuvhu akawanda pachiteshi, waya yakajairika inoda kuve yakakura kuti itakure yazvino. Mumamiriro ezvinhu aya sarudza tambo yakajairika imwe kana maviri saizi yakakura kupfuura inodiwa
• Paunenge uchigadzira zvinongedzo mumunda, ingo shandisa gel yakazadzwa kana girizi yakazadzwa zvibatanidza. Kukundikana kwakawanda kunoitika nekuda kwekusabatana zvakanaka. Izvo zvirinani kubatana pano, uye zvirinani chisimbiso chisingapindi mvura chinoita kuti sisitimu iite kwenguva refu pasina dambudziko
• Kuisa sensor yekunaya, isa waya pakati peCommon (C) neiyo Rain Sensor (R) materminal sezvakaratidzwa.

  

Pombi Kutanga Relay Connection

• Mutongi uyu haape mains simba rekutyaira pombi-pombi inofanirwa kufambiswa kuburikidza neyekunze relay uye yekuseta contactor.
• Iyo controller inopa yakaderera voltage chiratidzo chinoitisa relay iyo inogonesa iyo contactor uye pakupedzisira pombi
• Kunyange zvazvo mutongi ane chiyeuchidzo chekusingaperi uye nokudaro purogiramu yakashata haizokonzeri kukanganisa kwevharuvhu sezvinoitwa mune vamwe vatongi, ichiri tsika yakanaka kana uchishandisa nzira iyo mvura inobva papombi yekubatanidza zviteshi zvisina kushandiswa pachikwata kudzokera kune yekupedzisira. used station
• Izvi chaizvoizvo, zvinodzivisa mikana yepombi inoramba ichimhanya pamusoro wakavharwa

Kudzivirirwa kwepombi (System Test)

• Mune mamwe mamiriro ezvinhu hazvisi zvese zviteshi zvekushanda zvinogona kusungirirwa-zvemuenzanisoample, kana mutongi aikwanisa kumhanyisa zviteshi zve6 asi paingova newaya dzemumunda 4 chete uye mavharuvhu e-solenoid aripo kuti abatanidzwe.
• Mamiriro ezvinhu aya anogona kuunza njodzi kune pombi kana iyo system test routine yemutongi yatangwa
• Iyo system test routine sequences kuburikidza neese zviteshi zviripo pane controller
• Mu exampizvi zvinoreva kuti zviteshi 5 kusvika ku6 zvinotanga kushanda uye zvaizoita kuti pombi ishande yakavhara musoro
• Izvi zvinogona kukonzera zvachose pombi, pombi uye kukuvara kwechikepe
• Izvo zvinosungirwa kana iyo system test routine ichizoshandiswa, kuti ese asina kushandiswa, spare chiteshi, anofanirwa kubatanidzwa pamwe chete obva asungirirwa kune yekupedzisira chiteshi chekushanda nevhavha pairi.
• Kushandisa example, iyo yekubatanidza block inofanirwa kuve waya senge padhayagiramu iri pazasi

Single Phase Pump Installation
Inokurudzirwa kushandisa nguva dzose relay pakati pemutongi uye pombi inotanga

Kugadzirisa matambudziko

Zvemagetsi Zvinotaurwa

Zvemagetsi

• Magetsi
  
  • Mains supply: Iyi unit inoshandisa 240 volt 50 hertz single phase outlet
  • Iyo controller inodhonza 30 watt pa240VAC
  • Iyo yemukati inoshandura inoderedza iyo 240VAC kune yakawedzera yakaderera voltaguye kuwanikwa kwe24VAC
  • Iyo yemukati transformer inoenderana zvizere neAS/NZS 61558-2-6 uye yakaedzwa yakazvimirira uye kutongwa kuti inoenderana.
  • Iyi unit ine 1.25AMP simba rakaderera, rakanyanya kushanda toroidal transformer yekushanda kwehupenyu hurefu
• Magetsi Ekupa Simba:
  • Isa 24 volts 50/60Hz
  • Magetsi Anobuda:
  • Maximum ye1.0 amp
• Kune Solenoid mavharuvhu:
  • 24VAC 50/60Hz 0.75 amps max
  • Anosvika 2 mavharuvhu pachiteshi pane inbuilt modhi
• Kune Master Valve / Pombi Kutanga:
  • 24VAC 0.25 amps max
  • Transformer uye fuse huwandu hunofanirwa kuenderana nezvinobuda zvinodiwa

Overload Dziviriro

• Standard 20mm M-205 1 amp inokurumidza kuvhuvhuta girazi fuse, inodzivirira kubva kune simba rekuwedzera uye yemagetsi fuse yakamisikidzwa ku1AMP inodzivirira pakukanganisa kwemunda
• Yakanganisa chiteshi skip basa

Simba Kukundikana

• Mutongi ane chiyeuchidzo chekusingaperi uye nguva chaiyo yewachi, saka data inogara ichitsigirwa kunyange nekusavapo kwesimba rose
• Iyo unit ndeye fekitori yakarongedzerwa 3V CR2032 lithium bhatiri ine kusvika kumakore gumi memory backup.
• Iyo 9V alkaline bhatiri inochengetedza iyo data panguva yemagetsi outages, uye inokurudzirwa kubatsira kuchengetedza hupenyu hwe lithium bhatiri
• Tampkurira neyuniti kunobvisa waranti
• Mabhatiri haafambisi zvinobuda. Iyo yemukati transformer inoda mains simba kumhanya mavharuvhu

Wiring
Maseketi ekubuda anofanirwa kuiswa uye kuchengetedzwa zvinoenderana nekodhi yewaya yenzvimbo yako

Kushumira

Kushandira Controller yako
Mutongi anofanira kugara achishandirwa nemumiririri ane mvumo. Tevedza nhanho idzi kuti udzorere yako unit:

1. Dzorera magetsi emagetsi kune controller
   Kana iyo controller yakaoma-wired, ane hunyanzvi hwemagetsi anozodikanwa kubvisa iyo yese unit, zvichienderana nekukanganisa.
2.  Enderera kune imwe kusunungura uye kudzosa iyo yese controller netransformer kana kudzima musangano wepaneru chete sevhisi kana kugadzirisa.
3. Dhonza iyo 24VAC inotungamira pane controller 24VAC zviteshi kune kuruboshwe chaiko kweiyo terminal block.
4. Nyatsomaka kana ziva waya dzese dzevharuvhu zvinoenderana nematerminal adzinobatanidzwa nawo, (1–9)
   Izvi zvinokutendera iwe kuti uzviise nyore waya kumashure kune controller, kuchengetedza yako valve kudiridza chirongwa
5. Bvisa mawaya evharuvhu kubva kune terminal block
6. Bvisa mapaneru akazara kubva kune controller imba nekusunungura maviri screws mumakona ezasi efascia (maviri mamagumo eiyo terminal block)
7. Bvisa mutongi akazara kubva pamadziro achiburitsa lead
8. Nyatsoputira pani kana controller mukuputira yekudzivirira uye rongedza mubhokisi rakakodzera uye dzokera kune yako sevhisi mumiriri kana mugadziri.
   TampKutadza neyuniti kuchabvisa waranti.
9. Tsiva yako controller panel nekudzoreredza maitiro aya.
   Mutongi anofanira kugara achishandirwa nemunhu ane mvumo

Warranty

3 Year Yekutsiva Guarantee

• Holman inopa 3 makore kutsiva garandi neichi chigadzirwa.
• MuAustralia zvinhu zvedu zvinouya nezvivimbiso zvisingagone kubviswa pasi pemutemo weAustralian Consumer Law. Iwe une kodzero yekutsiviwa kana kudzoserwa kukundikana kukuru uye muripo kune chero imwe nzira inofanoona kurasikirwa kana kukuvara. Iwe zvakare une kodzero yekuti zvinhu zvigadziriswe kana kutsiviwa kana zvinhu zvikatadza kuve zvemhando inogamuchirika uye kukundikana hakufananidzi kukundikana kukuru.
• Nezve kodzero dzako dzemutemo dzataurwa pamusoro uye chero kodzero nemhinduro dzaunadzo pasi pemimwe mitemo ine chekuita nechigadzirwa chako cheHolman, tinokupawo vimbiso yeHolman.
• Holman anovimbisa chigadzirwa ichi kubva kune hurema hunokonzerwa nekutadza kushanda uye zvinhu zvemakore matatu kushandiswa kwepamba kubva pazuva rakatengwa. Munguva ino yekuvimbisa Holman achatsiva chero chigadzirwa chakaremara. Packaging uye mirairo inogona kusatsiviwa kunze kwekunge yakanganisa.
• Kana chigadzirwa chichitsiviwa munguva yevimbiso, garandi pachinhu chinotsiviwa chinopera makore maviri kubva pazuva rekutengwa kwechigadzirwa chekutanga, kwete makore maviri kubva pazuva rekutsiviwa.
• Kusvika pazvinotenderwa nemutemo, iyi Holman Replacement Guarantee haisanganisi mhosva yekurasikirwa kwakakoshera kana kumwe kurasikirwa kana kukuvadzwa kunokonzerwa nemidziyo yevanhu kunobva kune chero chikonzero. Izvo zvakare hazvibatanidzi hurema hunokonzerwa nechigadzirwa chisiri kushandiswa zvinoenderana nemirairo, kukuvara netsaona, kushandisa zvisizvo, kana kuve t.ampyakaitwa nevanhu vasina mvumo, isingabatanidzi kusakara uye kubvaruka uye haibhadhare mutengo wekukumbira pasi pewaranti kana kutakura zvinhu kuenda nekubva kunzvimbo inotengwa.
• Kana iwe uchifungidzira kuti chigadzirwa chako chingave chakaremara uye chinoda kujekeswa kana zano ndapota taura nesu zvakananga:
  1300 716 188
  support@holmanindustries.com.au
  11 Walters Drive, Osborne Park 6017 WA
• Kana uine chokwadi chekuti chigadzirwa chako hachina kukwana uye chakavharwa nemirairo yewaranti iyi, unozofanirwa kuratidza chigadzirwa chako chakakanganisika uye risiti yako yekutenga seumboo hwekutenga kunzvimbo yawakatenga kubva, uko mutengesi achatsiva chigadzirwa. iwe pachinzvimbo chedu.

Tinotenda zvikuru kuva nemi semutengi, uye tinoda kuti maita basa nekutisarudza. Tinokurudzira kunyoresa chigadzirwa chako chitsva pane yedu website. Izvi zvinoita kuti tive nekopi yekutenga kwako uye kumisa waranti yakawedzerwa. Ramba uchifambirana neruzivo rwakakodzera rwechigadzirwa uye zvakakosha zvinopihwa zvinowanikwa kuburikidza netsamba yedu.

www.holmanindustries.com.au/product-registration/
Thanks zvakare nekusarudza Holman