MoovAiPumpMP10AIDV-MP15AIDV-MP165AIDV
-MP2AI
Pompa Kolam Inverter Kab

MP2AI Ai Inverter Variabel Speed Pool Pump

Cathetan cilik saka sisih kita!
Matur nuwun kanggo dipercaya kita!
We ngerti carane akeh wektu iku penting lan kita pengin sampeyan seneng sabisa mangsa blumbang. Kanthi milih Produk Kolam Moov, sampeyan milih salah sawijining perusahaan paling canggih ing industri kasebut.
For over 30 years, pool pumps have known very little innovation until recently. The Moov Ai Pumps allies silence, performance, and ease of maintenance.
Mangga waca manual iki ing wektu nyata lan operate prodhuk minangka rinci sabanjuré. Ora ngetutake indikasi kasebut bisa nyebabake cilaka kanggo individu utawa ngrusak produk kasebut. Kanggo pitakon apa wae, hubungi Moov kanggo dhukungan teknis.
Sugeng rawuh ing Moov!
INSULATED WET END PUMP.
Gunakake konduktor tembaga ONLY.
Kanggo nggunakake blumbang, bak panas lan spa.
Ati-ati: HUBUNGE HANE NGGABUNG RESEP JENIS DIKOMPIN dening klompok interrupsi sirkuit ala.
Ati-ati: KANGGO NGAMENI Perlindhungan Terus Saka Hazaard SHOCK, GAMPANG GOLONGAN IDENTIKAL LANGSUNG Yen LAYANAN.
CAUTION: THIS PUMP IS FOR USE WITH PERMANENTLY-INSTALLED POOLS ONLY – DO NOT USE WITH STORABLE POOLS.

PETUNJUK KESELAMATAN PENTING

Nalika nginstal lan nggunakake peralatan listrik iki, pancegahan safety dhasar kudu ditindakake, kalebu ing ngisor iki:

1. Waca lan tindakake kabeh instruksi
2. PÈNGET - Kanggo nyuda resiko ciloko, aja ngidini bocah-bocah nggunakake prodhuk iki kajaba lagi diawasi kanthi rapet.
3. PÈNGET – Resiko Kejut Listrik. Sambungake mung kanggo sirkuit cabang dilindhungi dening ground-fault circuit-interrupter (GFCI). Hubungi tukang listrik sing mumpuni yen sampeyan ora bisa verifikasi manawa sirkuit kasebut dilindhungi dening GFCI.
4. Unit kasebut kudu disambungake mung menyang sirkuit sumber sing dilindhungi dening interrupter sirkuit lemah (GFCI). GFCI kuwi kudu diwenehake dening installer lan kudu dites kanthi rutin. Kanggo nyoba GFCI, pencet tombol test. GFCI kudu ngganggu daya. Pencet tombol reset. Daya kudu dibalèkaké. Yen GFCI ora bisa digunakake kanthi cara iki, GFCI rusak. Yen GFCI interrupts daya kanggo kumpa tanpa tombol test di-push, saiki lemah mili, nuduhake kamungkinan saka kejut listrik. Aja nggunakake pompa iki. Pedhot sambungan pompa lan supaya masalah didandani dening wakil layanan qualified sadurunge nggunakake.
5. PÈNGET – Kanggo nyuda resiko kejut listrik, ganti kabel sing rusak langsung.
6. CAUTION – This pump is for use with permanently-installed pools and may also be used with hot tubs and spas if so marked. Do not use it with storable pools. A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity.
7. Aja nginstal ing pager njaba utawa ing ngisor rok bak panas utawa spa.
8. A solid copper bonding conductor not smaller than 8 AWG (8.4 mm2) shall be connected from the accessible wire connector on the motor to all metal parts of the swimming pool, spa, or hot tub structure and to all electrical equipment, metal conduit, and metal piping within 5 feet (1.5 m) of the inside walls of a swimming pool, spa, or hot tub, when the motor is installed within 5 feet of the inside walls of the swimming pool, spa, or hot tub.
9. Kanggo Digunakake Kanthi Kolam Renang, Hot Tubs, lan Spa.
10. AWAS: Pompa iki mung kanggo Gunakake Kolam sing Dipasang Permanen - Aja Gunakake Kolam sing Bisa Disimpen.
11. AWAS: Kanggo nyuda resiko kejut listrik, pasang paling sethithik 6 kaki saka tembok njero blumbang. Aja nggunakake kabel extension.
12. AWAS: Kanggo mesthekake pangayoman terus marang bebaya kejut, gunakake mung bagean panggantos sing padha nalika servis.
13. Pompa iki digunakake kanggo kolam renang sing dipasang permanen ing lemah utawa ing ndhuwur lemah lan uga bisa digunakake karo bak panas lan spa kanthi suhu banyu ing sangisore 50 ℃. Amarga cara instalasi tetep, pompa iki ora dianjurake kanggo digunakake ing blumbang ing ndhuwur lemah sing bisa dibongkar kanggo panyimpenan.
14. Pompa ora submersible.
15. Aja mbukak ing njero kandang motor drive.
16. SIMPAN INSTRUCTIONS IKI.

WARNING:

• Fill the pump with water before starting. Do not run the pump dry. In case of dry run,  mechanical seal will be damaged and the pump will start leaking.
• Sadurunge nglayani pompa, mateni daya menyang pompa kanthi medhot sirkuit utama menyang pompa lan ngeculake kabeh tekanan saka pompa lan sistem pipa.
• Aja ngencengi utawa ngeculake sekrup nalika pompa digunakake.
• Priksa manawa inlet lan outlet pompa ora diblokir karo bahan asing.

SPESIFIKASI TEKNIS

Model	Daya (THP)	Ampumur (A)	Voltage (V)	Frekuensi (Hz)	Qmax (GPM AS)	Hmax (Ft)
MP10AIDV	0.85 THP	7.0A	115V	50/60	106	62
		3.5A	230V		106
MP15AIDV	1.25 THP	8.3A	115V		110	66
		5.2A	230V		123
MP165A1DV	1.65 THP	9.6A	115V		119	69
		6.5A	230V		132
MP2AI	2.00 THP	8.0A	220-240V		178	75

UKURAN UMUM (mm)

INSTALASI

4.1. Lokasi Pump

1. Instal pump minangka cedhak blumbang sabisa, kanggo ngurangi mundhut gesekan lan nambah efficiency, nggunakake cendhak, nyedhot langsung lan bali piping.
2. Kanggo ngindhari sinar srengenge langsung, panas utawa udan, dianjurake kanggo nyelehake pompa ing jero ruangan utawa ing iyub-iyub.
3. Aja nginstal pompa ing iklanamp utawa lokasi non-ventilated. Tansah pompa lan motor paling sethithik 150mm adoh saka alangan, motor pompa mbutuhake sirkulasi udara gratis kanggo pendinginan.
4. Pompa kudu dipasang kanthi horisontal lan tetep ing bolongan ing dhukungan kanthi sekrup kanggo nyegah gangguan lan geter sing ora perlu.

4.2. Pipa

1. The pump inlet/outlet union size: optional with metric (48.3 or 60.3mm) or imperial (1.5” or 2”).
2. For optimization of the pool plumbing, a larger pipe size should be used. It is recommended to use a pipe with size of 2”.
3. When installing the inlet and outlet fittings (joints) with the pluming, use the special sealant for PVC material.
4. Ukuran garis nyedhot kudu padha utawa luwih gedhe tinimbang diameter saluran inlet, supaya ora ngisep hawa pompa, sing bakal mengaruhi efisiensi pompa.
5. To reduce friction loss and improve efficiency, plumbing on the suction and return side should be short and direct.
6. Sistem nyedhot kebanjiran kudu dipasang klep ing loro nyedhot pump lan bali baris, kang trep kanggo pangopènan rutin. Katup, sikut, utawa tee sing dipasang ing garis nyedhot kudu ora luwih cedhak karo ngarep pompa tinimbang kaping pitu diameter garis nyedhot.
7. Use a check valve in the return line where there is a significant height between the return line and the outlet of the pump to prevent the pump from the impact of medium recirculation and pump-stopping water hammer.

4.3. Katup lan Fitting

1. Siku kudu ora luwih cedhak saka 350mm menyang inlet. Aja masang elbows 90 ° langsung menyang inlet/outlet pump. Sendi kudu nyenyet.
2. Sendi kudu nyenyet.* The pump inlet/outlet union size: optional with metric (48.3 or 60.3mm) or imperial (1.5” or 2”)
3. Use the UNION KIT supplied by the pump manufacturer (Refer to Figure 3). Do not use other fittings to connect the pump inlet/outlet, in case the fittings are not match and damage the pump body.

4.4. Check before initial startup

1. Priksa manawa poros pompa bisa muter kanthi bebas;
2. Priksa manawa sumber daya voltage lan frekuensi salaras karo nameplate;
3. Ngadhepi bilah penggemar, arah rotasi motor kudu searah jarum jam;
4. Do not run without water. Will the basket initially before starting the product.

4.5. Syarat aplikasi

Suhu sekitar	Kisaran suhu: -10 ~ 42 ℃
Suhu banyu maksimal	50 ℃
Kolam uyah	Konsentrasi uyah nganti 3.5%, yaiku 35g / l
Kelembapan	≤90% RH, (20 ℃ ± 2 ℃)
Instalasi	Pompa bisa dipasang maksimal. 2m ndhuwur permukaan banyu
pangayoman	Kelas F, IP55

SETTING lan OPERASI

5.1. Tampilan ing panel kontrol

1. konsumsi daya
2. Kapasitas mlaku / Laju aliran
3. Indikator WIFI
4. Unit aliran
5. Periode wektu
6. Timer 1/2/3/4

Backwash / mbukak kunci
Up/down: kanggo ngganti nilai (kapasitas/aliran/wektu)
  Ngalih ing antarane Mode Manual-Inverter lan Mode Auto-Inverter
Manual-Inverter Mode: The running capacity will be set manually between 30%-120%. Will be shown in percentage.
Auto-Inverter Mode: The running capacity will be automatically adjusted between 30%-120% according to the preset flow rate.
Mode standar yaiku mode Manual-Inverter.
Setelan wektu
On/off
5.2. Proses wiwitan rampungview

1. Langkah 1: Wiwiti
   Pencet terus luwih saka 3 detik kanggo mbukak kunci layar.
   Pencet  kanggo miwiti pompa.
2.  Langkah 2: Self-priming
   Pompa bakal miwiti ngetung mudhun saka 1500s; Nalika sistem ndeteksi pump kebak banyu, iku bakal mandheg ngetung mudhun lan metu priming kanthi otomatis.
   Pangguna bisa ngetik setelan parameter kanggo mateni fungsi self-priming standar (ndeleng 5.10).
3. Langkah 3: Priksa dhewe
   The pump will recheck for 30s again to make sure the self-priming（Step2）is completed.
4.  Langkah 4: Pompa mlaku
   Pompa bakal mbukak ing 80% saka kapasitas mlaku ing wiwitan wiwitan sawise self-priming.

5.3. Wiwitan
Nalika daya diuripake, layar bakal madhangi nganti 3 detik, kode piranti bakal ditampilake, banjur bakal mlebu ing kahanan kerja normal. Nalika layar dikunci, mung tombol bakal padhang;
Pencet terus luwih saka 3 detik kanggo mbukak kunci layar. Layar bakal ngunci kanthi otomatis nalika ora ana operasi luwih saka 1 menit lan padhange layar bakal suda dadi 1/3 saka tampilan normal. Pencet singkat kanggo tangi layar lan mirsani paramèter operasi sing cocog.
5.4. Self-priming
Saben-saben pump diwiwiti, iku bakal miwiti self-priming.
Nalika pump nindakake poto-priming, bakal count mudhun wiwit saka 1500s lan mungkasi count mudhun kanthi otomatis nalika sistem ndeteksi pump kebak banyu, banjur sistem bakal recheck kanggo 30s maneh kanggo mesthekake yen poto-priming wis rampung.
Users can cancel self-priming manually by pressing luwih saka 3 detik. Pompa bakal mlebu mode Manual Inverter standar nalika wiwitan wiwitan.
Cathetan:
MP10AIDV, MP15AIDV, and MP165AIDV：
Pompa dikirim kanthi otomatis priming. Saben pompa diwiwiti maneh, bakal nindakake priming kanthi otomatis. Pangguna bisa ngetik setelan parameter kanggo mateni fungsi self-priming standar (pirsani 5.10)
MP2AI：

1. Pompa dikirim kanthi otomatis priming. Saben pompa diwiwiti maneh, bakal nindakake priming kanthi otomatis. Pangguna bisa ngetik setelan parameter kanggo mateni fungsi self-priming standar (pirsani 5.10)
2. Yen fungsi timer priming standar dipatèni, lan pump wis ora digunakake kanggo dangu, tingkat banyu ing basket strainer bisa mudhun. Pangguna bisa kanthi manual ngaktifake fungsi self-priming kanthi mencet loro kanggo 3 detik, wektu luwes saka 600s kanggo 1500s (nilai standar 600s).
3. After the manual self-priming is completed, the pump will return to the previous state before activating the manual self-priming. If the pump has entered the Auto Inverter mode previously, the pump will perform self-learning for 180s to redefine the adjustable flow range after the manual self-priming.
4. Pangguna bisa menet for more than 3 seconds to cancel the manual self-priming, and the pump will run the same as the manual self-priming is completed.

5.5. Backwash
Pangguna bisa miwiti backwash utawa re-circulation cepet ing sembarang negara mlaku kanthi mencet

	Default	Range setelan
Wektu	180s	Pencet  to adjust from 0 to 1500s with 30 seconds for each step
Kapasitas mlaku	100%	MMOAIDV, MP15AIDV, and MP165AIDV: 60-100%, enter the parameter setting (see 5.10)
		MP2AI: 80-100%, ketik setelan parameter (pirsani 5.10)

Metu backwash:
Nalika mode backwash urip, pangguna bisa terus for 3 seconds to cancel it, the pump will return to the previous state before backwash. If a speed limit is set by the user, the running capacity of the backwash will not exceed the set speed limit.
5.6. Manual-Inverter Mode (Easiest operating mode)

1		terus luwih saka 3 detik kanggo mbukak kunci layar;
2		Pencet to start. The pump will run at 80% of the running capacity after  self-priming.
3		Pencet kanggo nyetel kapasitas mlaku antarane 30% ~ 120%, saben langkah dening 5%
4		Pencet maneh kanggo ngalih menyang mode Auto-Inverter.

Cathetan:

1. When the pipeline resistance is too high, to maintain an adequate flow rate, users can set the running capacity to 105%-120%. The pump will run at a higher speed but will not exceed the rated power of each model.
2. If the pump has reached the rated power at 105% and users continues to increase the running capacity, the display will return to 105% when the motor speed is stabilized. again to switch to Auto-Inverter mode. or to set the running capacity between 30%~120%, each step by 5% to start. The pump will run at 80% of the running capacity after for more than 3 seconds to unlock the screen;

5.7. Auto-Inverter Mode (Advanced users)
Ing Mode Inverter Otomatis, pompa bisa kanthi otomatis ndeteksi tekanan sistem lan nyetel kacepetan motor kanggo nggayuh aliran sing disetel.

1		Mbukak kunci layar, penet kanggo ngalih saka mode Manual-Inverter menyang mode Auto-Inverter.
2		Tingkat aliran bisa diatur, kanthi mencet with 5 US GPM for each step.
3		The unit of flow rate could be changed to LPM, IMP GPM or m3/h, by pressing both kanggo 3 detik
4		Pencet kanggo ngalih menyang mode Manual-Inverter

Kisaran aliran luwes standar kanggo Moov Ai Pump kaya ing ngisor iki:

Model	Default kisaran tingkat aliran luwes
MP10AIDV	35-90 US GPM
MP15AIDV	35-110 US GPM
MP165AIDV	35-130 US GPM
MP2AI	35-160 US GPM

Self-learning ( Only suitable for MP2AI ):
When first switching to the Auto Inverter mode, the system will perform the self-priming process (see 5.4) and then the self-learning process for 180s and redefine the adjustable flow range of the pump by detecting the pipeline pressure.
eg: the default adjustable flow range of Moov Ai MP2AI is 35-160 US GPM, after self-learning, the range may be redefined to 35-130 US GPM. If the set flow is beyond the current adjustable range, the actual achievable flow rate will be displayed after the motor speed is stabilized.
Cathetan:

1. Sawise priming pisanan, pompa bakal nemtokake maneh kisaran aliran sing bisa diatur. Tekanan pipa bakal dicathet dening sistem sawise pompa mlaku ing aliran / kapasitas sing disetel sajrone 5 menit tanpa operasi liyane.
2. During the pump running, if it is detected that the pipeline pressure changes beyond a certain range, the icon of % or m³/h (or other flow units) symbol will flash for 5 minutes. If the change lasts for 5 minutes, the pump will perform a self-priming and self-learning process, and redefine the flow range accordingly.
3. Sawise redefinition saka sawetara aliran, pump bakal kanthi otomatis nyetel kapasitas mlaku kanggo tekan aliran pesawat.
4. Users can set the time interval to trigger the self-leaning automatically in the parameter setting (see 5.10) to ensure the accuracy of the flow rate.

5.8. Mode wektu
Kapasitas on/off lan mlaku pompa bisa diatur dening timer, sing bisa diprogram saben dina yen perlu.

1	Ketik setelan timer kanthi mencet
2	Pencet   kanggo nyetel wektu lokal.
3	Pencet kanggo konfirmasi lan pindhah menyang setelan wektu-1.
4	Pencet   kanggo milih wektu mlaku sing dikarepake, kapasitas mlaku utawa tingkat aliran (nalika lambang% sumunar, pangguna bisa ngganti nyetel tingkat aliran kanthi mencet ).
5	Baleni langkah ing ndhuwur kanggo nyetel 3 timer liyane.
6	Tahan 3 detik kanggo nyimpen setelan lan ngaktifake mode timer.
7	Priksa 4 timer kanggo mesthekake yen ora ana setelan sing ora bener.

Cathetan:

1. Nalika mode timer diaktifake, yen periode wektu nyetel ngemot wektu saiki, pump bakal miwiti mlaku miturut kapasitas mlaku pesawat utawa tingkat aliran. Yen periode wektu sing disetel ora ngemot wektu saiki, nomer timer  (utawa 1 utawa 2 utawa 3 utawa 4) sing bakal diwiwiti bakal ditampilake ing controller lan lampu kilat, bakal nampilake periode wektu sing cocog, nuduhake setelan wektu sing sukses.
2. Sajrone setelan timer, yen sampeyan pengin bali menyang setelan sadurunge, tahan loro kanggo 3 detik. Yen sampeyan ora perlu nyetel kabeh 4 timer, sampeyan bisa terus kanggo 3 detik, sistem bakal kanthi otomatis nyimpen nilai pesawat saiki lan ngaktifake mode timer.
3. Pangguna bisa mbatalake mode timer kanthi mencet

5.9. Winterizing
In cold climate environments where the pools are closed for winter, the pump must be drained from the strainer and the pump housing. Both unions must be disconnected and the pump may be covered and protected from the snow fall or disconnected and kept indoor for protection. Warranty calls on unproperly winterization will not be covered by warranty.
5.10. Setelan Parameter

Mulihake setelan pabrik	Ing mode mati, tahan loro kanggo 3 detik
Priksa versi piranti lunak	Ing mode mati, tahan loro kanggo 3 detik
Enter parameter setting as ngisor	Ing mode mati, tahan loro  for 3 seconds; If current address does not need to be adjusted, hold both   press to next address menyang alamat sabanjure

Alamat Parameter	Katrangan	Setelan Default	Setelan Range
1	Dig (Digital input 2)	100%	MP10AIDV, MP15AIDV, and MP165AIDV: 1.Speed: 30-120%, by 5% increments; 2.Flow: MP10AIDV: 35-90 US GPM, MPI5AIDV: 35-110 US GPM. MP165AIDV: 35-130 US GPM, by 5 US GPM increments; Cathetan: Pencet to switch to flow rate setting. MP2AI: Speed: 30-120%, by 5% increments.
2	Di3 (Digital input 3)	80%
3	Di4 (Digital input 4)	40%
4	Kapasitas backwash	100%	MP10AIDV, MP15AIDV, and MP165AIDV: 1.Speed: 60-100%. by 5% increments: 2.Flow: MPIOAIDV: 55-90 US GPM, MPI5AIDV: 65-110 US GPM, MP165AIDV: 80-130 US GPM. by 5 US GPM increments: Cathetan: Pencet to switch to flow rate setting. MP2AI: Speed: 80-100%, by 5% increments.
5	Mode kontrol Analog Input	0	0: kontrol saiki 1: Voltage ngontrol

6	Enable or disable the self-priming at each start	25	25: mbisakake 0: mateni
7	dilindhungi	0	Ora bisa diowahi
8	Wektu sistem	0:00	00:00 – 23:59
9	Preset 1 of the skimmer mode (skimmer cycle. skimmer duration. skimmer speed or flow)	01:00 00:03 100%	‘Skimmer cycle: 1-24h. lh for each step; ‘Skimmer duration: 1-30min, 1min for each step: ‘Skimmer speed: 30%-100% by 5% increments: ‘Skimmer flow (only the following models can adjust): MPIOAIDV: 35-90 US GPM. MPISAIDV: 35-110 US GPM. MP165AIDV: 35-130 US GPM. by 5 US GPM increments; Cathetan: Pencet   kanggo ngalih menyang setelan tingkat aliran
10	Periode wektu prasetel 1 saka mode skimmer	7:00-21:00	Wektu wiwitan: 00:00-24:00 Wektu pungkasan: 00:00-24:00
11	watesan kacepetan	100%	MPIOAIDV, MPISAIDV, and MP165AIDV: 1.Speed: 60%-100%. by 5% increments (100% means no speed limit) 2.Flow: MPIOAIDV: 55.90 US GPM. MP15AIDV: 65-110 US GPM. MP165AIDV: 80-130 US GPM. by 5 US GPM increments: Cathetan: Pencet to switch to flow rate setting. MP2AI: Speed: 60%-100%. by 5% increments (100% means no speed limit)
12	alamat RS485	170(0xAM	160-190 (OxA0-0x8F). saben langkah 1.
13	dilindhungi (Suitable for MPIOAIDV, MP15AIDV, MP165AIDV)	0	Ora bisa diowahi
	Time intervals to trigger the self-learning automatically (Suitable for MP2A1)	0	0, 1. 3. 5. 7. 14. 21. 28 (day) (.0′ means will not trigger the self-learning automatically)

Kanggo example: Kepiye cara ngaktifake / mateni Fungsi Self-Priming?

 

1. Enter parameter setting: Under off mode, hold both kanggo 3 detik;
2. Select parameter address: Press to address 6;
3. Enable or disable the self-priming at each start: Adjust by pressing  25 = Ngaktifake,
   0 = Pateni.

OPERASI WIFI

Download MOOV POOL APPRegistrasi akun
Register liwat e-mail utawa aplikasi pihak katelu.a. Email/iOS RegistrationNggawe Omah
Setel jeneng ngarep lan pilih lokasi piranti. (Disaranake nyetel lokasi supaya cuaca bisa ditampilake ing App kanggo penak)

App pasangan

Priksa manawa pompa sampeyan wis diuripake sadurunge miwiti.
Opsi 1 (Disaranake): Kanthi Wifi lan Bluetooth
(Persyaratan jaringan: 2.4GHz; 2.4Ghz lan 5GHz dadi siji SSID; nanging ora ana jaringan 5GHz sing kapisah)

1. Mangga konfirmasi yen telpon wis nyambung menyang Wi-Fi lan Bluetooth urip.
2. Pencet kanggo 3 detik nganti krungu "Bip" kanggo mbukak kunci layar. Pencet nganti 5 detik nganti krungu "Bip" banjur uculake. Bakal flash.
3. Klik "Tambah Piranti", banjur tindakake pandhuan kanggo masangake piranti.

Opsi 2: Kanthi Wifi (syarat jaringan: mung 2.4GHz)

1. Please confirm that your phone is connected to Wifi.
2. Pencet kanggo 3 detik nganti krungu "Bip" kanggo mbukak kunci layar. Pencet nganti 5 detik nganti krungu "Bip" banjur uculake. Bakal flash.
3. Klik "Tambah Piranti", banjur tindakake pandhuan kanggo masangake piranti.

Operasi

1. Nggunakake mode Auto Inverter:
2. Nggunakake mode Inverter Manual:

Nuduhake Piranti karo anggota kulawarga

After pairing, if your family members also want to control the device, please let your family members register “InverFlow” first, and then the administrator can operate as ing ngisor iki:Umpan balik
Yen sampeyan duwe masalah nalika nggunakake, welcome kanggo ngirim saran.Kabar:

1. Prakiraan cuaca mung kanggo referensi;
2. The power consumption data is for reference only, as it may be affected by network problems and imprecision of the calculation;
3. App tundhuk nganyari tanpa kabar.

KONTROL EKSTERNAL
External control can be enabled via following contacts. If more than one external control is enabled, the priority is as below: Digital Input > RS485 > Panel control.

1. AC power input-Power cord connection
2. Digital input and RS485 connection

Kontrol njaba	warna	Katrangan
Input Digital	abang	Di4 (Digital Input 4)
	ireng	Di3 (Digital Input 3)
	Putih	Di2 (Digital Input 2)
	abu-abu	Di1 (Digital Input 1)
	kuning	Digital Ground (COM)
RS485	Ijo	RS485-A
	coklat	RS485-B

a. Input digital
Kapasitas mlaku ditemtokake dening negara input digital,

1. When Di1(Grey) connects with COM(Yellow), the pump will be mandatory to stop; if disconnected, the digital control will be invalid;
2. When Di2(White) connects with COM(Yellow), the pump will be mandatory to run at 100%; if disconnected, the control priority will be back on panel control;
3. When Di3(Black) connects with COM(Yellow), the pump will be mandatory to run at 80%; if disconnected, the control priority will be back on panel control;
4. When Di4(Red) connects with COM(Yellow), the pump will be mandatory to run at 40%; if disconnected, the control priority will be back on panel control;
5. Kapasitas input (Di2/Di3/Di4) bisa diowahi miturut setelan parameter.

b. RS485
Kanggo nyambungake karo RS485-A (Ijo) lan RS485-B (Brown), pompa bisa dikontrol liwat protokol komunikasi Modbus 485.

pangayoman lan GAGAL

8.1. High Temperature Warning and Speed Reduction
In “Auto Inverter/Manual Inverter Mode” and “Timer mode” (except backwash/self-priming), when the module temperature reaches the high-temperature warning trigger threshold (81℃), it enters the high-temperature warning state; when the temperature drops to the high-temperature warning release threshold (78℃), the high-temperature warning state is released. The display area alternately displays AL01 and running speed or flow.
Yen AL01 ditampilake pisanan, kapasitas mlaku bakal suda kanthi otomatis kaya ing ngisor iki:

1. Yen kapasitas operasi saiki luwih saka 100%, kapasitas mlaku bakal kanthi otomatis suda kanggo 85%;
2. If current operating capacity is between 85% and 100%, the running capacity will be automatically reduced by 15%;
3. If current operating capacity is between 70% and 85%, the running capacity will be automatically reduced by 10%;
4. Yen kapasitas operasi saiki luwih murah tinimbang 70%, kapasitas mlaku bakal suda kanthi otomatis 5%.

8.2. Ing voltage pangayoman
MP10AIDV, MP15AIDV, and MP165AIDV：
The device is compatible with both 230V and 115V AC power input.

1. AC Power Input：230V
   Nalika piranti ndeteksi yen input voltage kurang saka 198V, piranti bakal matesi kacepetan mlaku saiki. Area tampilan gantian nampilake AL02 lan kacepetan mlaku utawa aliran.
   1) Nalika input voltage kurang saka utawa padha karo 180V, kapasitas mlaku bakal diwatesi nganti 70%;
   2) When the input voltage sawetara ing 180V - 190V, kapasitas mlaku bakal diwatesi kanggo 75%;
   3) When the input voltage sawetara ing 190V - 198V, kapasitas mlaku bakal diwatesi kanggo 85%.
2. AC Power Input：115V
   Nalika piranti ndeteksi yen input voltage kurang saka 98V, piranti bakal matesi kacepetan mlaku saiki.
   The display area alternately displays AL02 and running speed or flow.
   1) When the input voltage sawetara ing 85V - 90V, kapasitas mlaku bakal diwatesi kanggo 75%;
   2) When the input voltage sawetara ing 90V - 98V, kapasitas mlaku bakal diwatesi kanggo 85%.

Cathetan: Yen input voltage kurang saka 85V, kode kesalahan E001(Abnormal Input Voltage, ndeleng 8.4) bakal ditampilake.
MP2AI：
Nalika piranti ndeteksi yen input voltage kurang saka 197V, piranti bakal matesi kacepetan mlaku saiki. Area tampilan gantian nampilake AL02 lan kacepetan mlaku utawa aliran.

1. Nalika input voltage kurang saka utawa padha karo 180V, kapasitas mlaku bakal diwatesi nganti 70%;
2. Nalika input voltage sawetara ing 180V - 190V, kapasitas mlaku bakal diwatesi kanggo 75%;
3. Nalika input voltage sawetara ing 190V - 197V, kapasitas mlaku bakal diwatesi kanggo 85%.

8.3. Ngatasi masalah

Masalah	Bisa nyebabake lan solusi
Pompa ora diwiwiti	•Fault Power Supply, kabel pedhot utawa risak. •Sekring diunekake utawa kakehan termal mbukak. • Priksa rotasi poros motor kanggo gerakan bebas lan ora ana alangan. •Because of long time lying idle. Unplug the power supply and manually rotate motor rear shaft a few times with a screwdriver.
Pompa ora prima	•Empty pump/strainer housing. Make sure the pump/strainer housing is filled with water and the 0 ring of cover is clean. • Sambungan longgar ing sisih nyedhot. • Kranjang saringan utawa kranjang skimmer sing diisi lebu. •Sisih nyedhot clogged. •Distance between pump inlet and liquid level is higher than 2m, the installation height of pump should be lowered.
Aliran Banyu Sedheng	• Pump ora Perdana. •Air ngetik pipa nyedhot. •Keranjang kebak lebu. • Tingkat banyu ora nyukupi ing blumbang.
Pompa dadi rame	•Air leak in suction piping, cavitation caused by restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted discharge return lines. •Getaran disebabake instalasi sing ora bener, lsp. • Rusak bantalan motor utawa impeller (kudu hubungi supplier kanggo ndandani).

8.4. Kode kesalahan
MP10AIDV, MP15AIDV, and MP165AIDV：
Nalika piranti ndeteksi kegagalan, piranti bakal mandheg kanthi otomatis lan nampilake kode kesalahan. Sawise mandheg 15 detik, priksa manawa gagal wis diresiki. Yen diresiki, pompa bakal bisa digunakake maneh.

Item	Kesalahan Kode	Rincian
1	E001	Katrangan	Input abnormal voltage: sumber daya voltage is out of the range of 165V to 27W.
		Proses	Pompa bakal mandheg kanthi otomatis sajrone 15 detik lan bisa digunakake maneh yen ndeteksi vol sumber dayatage ana ing jangkoan.
2	E002	Katrangan	Output over current: The peak current of the pump is higher than the protection current.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for thrice continuously, the pump will shut down and need to be checked and restarted manually.
3	E102	Katrangan	Heat sink error : The heat sink temperature reaches 91°C for 10sec. Or the heat sink sensor detects an open or short circuit.
		Proses	1.The pump will stop automatically for 30 sec and resume working if it detects the heat sink temperature is less than 81°C. 2.The pump will stop automatically for 15 sec and resume working if it detects the heat sink sensor is not open or short circuit.
4	E103	Katrangan	Master driver board error: The Master driver board is faulty.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for thrice continuously, the pump will shut down and need to be checked and restarted manually.
5	E104	Katrangan	Phase-deficient protection: Motor cables are not plugged into the master drive board.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for thrice continuously, the pump will shut down and need to be checked and restarted manually.
6	E201	Katrangan	Circuit board error: When the pump power off, the bias voltage saka sampling circuit is out of the range of 2.4V-2.6V.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
7	E203	Katrangan	RTC time reading error: Reading and writing the information of timer clock is incorrect.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
8	E204	Katrangan	Display Board EEPROM reading failure: Reading and writing the information of display board EEPROM is incorrect.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
9	E205	Katrangan	Communication Error: The communication between display board

			lan Papan driver master punika Gagal luwih 15 sec.
		Proses	Pompa bakal mandheg kanthi otomatis sajrone 15 detik lan bisa digunakake maneh yen ndeteksi komunikasi antarane papan tampilan lan papan driver master suwene 1 detik.
10	E207	Katrangan	No water protection: The pump is lack of water.
		Proses	Mungkasi pompa kanthi manual, isi pompa nganggo banyu lan miwiti maneh. Yen kedadeyan kaping pindho terus-terusan, pompa bakal mati lan kudu dipriksa kanthi manual.
11	E209	Katrangan	Loss of prime: The pump cannot self-priming due to the reasons such as exceeding the suction range or the pipeline is too complicated.
		Proses	Priksa pompa utawa pipa yen ora ana bocor, banjur isi pompa nganggo banyu lan miwiti maneh.

MP2AI：
Nalika piranti ndeteksi kegagalan, piranti bakal mandheg kanthi otomatis lan nampilake kode kesalahan. Sawise mandheg 15 detik, priksa manawa gagal wis diresiki. Yen diresiki, pompa bakal bisa digunakake maneh.

Item	Kesalahan Kode	Rincian
1	E001	Katrangan	Input abnormal voltage: sumber daya voltage is out of the range of 16W to 275V.
		Proses	Pompa bakal mandheg kanthi otomatis sajrone 15 detik lan bisa digunakake maneh yen ndeteksi vol sumber dayatage ana ing jangkoan.
2	E002	Katrangan	Output over current: The peak current of the pump is higher than the protection current.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for three times continuously, the pump will shut down and need to be checked and restarted manually.
3	E101	Katrangan	Heat sink overheat: The heat sink temperature reaches 91°C for lOsec.
		Proses	Pompa bakal mandheg kanthi otomatis sajrone 30 detik lan bisa digunakake maneh yen ndeteksi suhu sink kurang saka 81 ° C.
4	E102	Katrangan	Heat sink sensor error: The heat sink sensor detects an open or short circuit.
		Proses	Pompa bakal mandheg kanthi otomatis sajrone 15 detik lan bisa digunakake maneh yen ndeteksi sensor sink panas ora mbukak utawa sirkuit cendhak.

5	E103	Katrangan	Master driver board error: The Master driver board is faulty.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for three times continuously, the pump will shut down and need to be checked and restarted manually.
6	E104	Katrangan	Phase-deficient protection: Motor cables are not plugged into the master drive board.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for three times continuously, the pump will shut down and need to be checked and restarted manually.
7	E105	Katrangan	arus AC sampling circuit failure: When the pump power off, the bias voltage saka sampling circuit is out of the range of 2.4V-2.6V.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
8	E106	Katrangan	DC abnormal voltage: The DC voltage metu saka sawetara 210V kanggo 420V.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for three times continuously, the pump will shut down and need to be checked and restarted manually.
9	E107	Katrangan	PFC protection: PFC protection occurs on the Master driver board.
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for three times continuously, the pump will shut down and need to be checked and restarted manually.
10	E108	Katrangan	Motor power overload: Motor power exceeds the rated power by 1.2 times
		Proses	The pump will stop automatically for 15 sec and then resume working, if this occurs for three times continuously, the pump will shut down and need to be checked and restarted manually.
11	E201	Katrangan	Circuit board error: When the pump power off, the bias voltage saka sampling circuit is out of the range of 2.4V-2.6V.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
12	E203	Katrangan	RTC time reading error: Reading and writing the information of timer clock is incorrect.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
13	E204	Katrangan	Display Board EEPROM reading failure: Reading and writing the information of display board EEPROM is incorrect.
		Proses	Pompa kudu dipateni lan diwiwiti kanthi manual.
14	E205	Katrangan	Communication Error: The communication between display board and master driver board is failure lasts 15 sec.

		Proses	Pompa bakal mandheg kanthi otomatis sajrone 15 detik lan bisa digunakake maneh yen ndeteksi komunikasi antarane papan tampilan lan papan driver master suwene 1 detik.
15	E207	Katrangan	No water protection: The pump is lack of water.
		Proses	Mungkasi pompa kanthi manual, isi pompa nganggo banyu lan miwiti maneh. Yen kedadeyan kaping pindho terus-terusan, pompa bakal mati lan kudu dipriksa kanthi manual.
16	E209	Katrangan	Loss of prime: The pump cannot self-priming due to the reasons such as exceeding the suction range or the pipeline is too complicated.
		Proses	Priksa pompa utawa pipa yen ora ana bocor, banjur isi pompa nganggo banyu lan miwiti maneh.

MAINTENANCE

Kosongake kranjang saringan kanthi asring. Kranjang kasebut kudu dipriksa liwat tutup sing transparan lan dikosongake yen ana tumpukan sampah ing njero. Pandhuan ing ngisor iki kudu ditindakake:

1. Pedhot sumber daya.
2. Copot tutup kranjang saringan berlawanan arah jarum jam lan copot.
3. Angkat kranjang saringan.
4. Mbusak sampah sing kepepet saka kranjang, mbilas lebu yen perlu.
   Cathetan: Aja ngalahake kranjang plastik ing permukaan sing atos amarga bisa nyebabake karusakan
5. Priksa basket kanggo pratandha saka karusakan, ngganti.
6. Check the lid O-ring for stretching, tears, cracks or any other damage.
7. Ganti tutup, kenceng tangan cukup.
   Cathetan: Mriksa lan ngresiki basket strainer kanthi periodik bakal mbantu ndawakake umure.

JAMINAN & PENGECUALIAN

Wigati dimangerteni manawa garansi diwiwiti nalika tuku. Yen tuku iki telat kayata ing mbangun blumbang anyar utawa instalasi bakal telat, tanggal instalasi kudu mbuktekaken karo dokumentasi cocok kanggo miwiti babar pisan ing wektu instalasi. Garansi mung sah nalika pisanan diinstal.
Sawetara pratelan ora bakal disetujoni ing kahanan apa wae dening Moov Pool Products. Klaim kasebut kalebu lan ora diwatesi ing:

• – Pompa rusak amarga winterization ora tepat. Winterization cocok bisa ditemokaké ing Moov Pool Products websitus utawa ing kaca 10 manual iki. Sembarang tuntutan standar winterization liyane bakal ditolak.
• Pump damaged by meteorological events such Hurricanes, Tornados, Hail, Earthquakes and any other act of god event.
• Unit sing ora dipasang dening teknisi sing cocog. Pakaryan perdagangan teknisi kasebut beda-beda gumantung saka wilayah instalasi lan bisa uga kalebu teknisi HVAC utawa listrik. Kabel listrik utawa manipulasi produk kalebu.
  Any unsatisfactory claim. Pumps efficiency will vary depending on various factors such as length of pipes, filters, internal pressure, pool size, and much more. Please always refer to your pool expert to select the right unit tailored to your needs or contact Moov Pool Products for a recommendation.

Kabeh pratelan babar pisan kudu disetujoni dening karyawan Moov Pool Products sah. Kanggo informasi luwih lengkap babagan garansi utawa ngirim pratelan, hubungi Moov Pool Products.
Produk Kolam Moov
Canadian head office located in Quebec City, Quebec, Canada (450-328-5858)
U.S.A head office located in Ft Lauderdale, Florida, USA (407-559-2077) www.moovsa.com
Pabrik nduweni hak interpretasi pungkasan lan tetep nduweni hak kanggo mungkasi utawa ngganti spesifikasi lan desain produk tanpa kabar sadurunge, ora perlu nanggung kewajiban sing diasilake.

PEMBUANGAN

When disposing the product, please sort the waste products as electrical or electronic product waste or hand it over to the local waste collection system.
Koleksi lan daur ulang peralatan sampah sing kapisah nalika dibuwang bakal mbantu supaya bisa didaur ulang kanthi cara sing nglindhungi kesehatan manungsa lan lingkungan.
Hubungi panguwasa lokal kanggo informasi babagan ngendi sampeyan bisa nyelehake pompa banyu kanggo daur ulang.

Dokumen / Sumber Daya

MOOV MP2AI Ai Inverter Variable Speed Pool Pump [pdf] Instruksi Manual MP10AIDV, MP15AIDV, MP165AIDV, MP2AI, MP2AI Ai Inverter Variable Speed Pool Pump, MP2AI, Ai Inverter Variable Speed Pool Pump, Variable Speed Pool Pump, Speed Pool Pump, Pool Pump

Referensi

• Manual pangguna