CIMC Firmware Version 4.3(5.250030) M6
Update Patch for Secure Network Analytics v7.5.3
Patch imudojuiwọn famuwia CIMC M6 fun Awọn atupale Nẹtiwọọki to ni aabo
This document provides a description of the CIMC 4.3(5.250030) Firmware M6 Common Update Patch for Secure Network Analytics along with instructions for installing the patch.
This firmware update can be performed using either the SWU file/procedure or the ISO file/procedure outlined below:
- The SWU file, patch-common-SNA-FIRMWARE-20250403-v2-01.swu, updates the CIMC firmware to version 4.3(5.250030) for UCS C-Series M6 hardware running Secure Network Analytics v7.5.3.
- Alternatively, you can also use the ISO file, patch-common-SNA-FIRMWARE20250403-M6-REL.iso, to update the CIMC firmware to version 4.3(5.250030) for UCS C-Series M6 hardware with Secure Network Analytics v7.5.3.
As part of the update process, make sure to install the required rollup patches on your appliances.
M6 Hardware
This patch applies to UCS C-Series M6 hardware for the Secure Network Analytics appliances shown in the following table.
M6 Hardware
| Alakoso 2300 | Sensọ ṣiṣan 1300 |
| Data Node 6300 | Sensọ ṣiṣan 3300 |
| Alakojo sisan 4300 | Sensọ ṣiṣan 4300 |
Make sure you update all physical appliances.
Alaye ni Afikun
For more details about CIMC version 4.3(5.250030), refer to Release Notes for Cisco UCS Rack Server Software.
Gbigba lati ayelujara ati fifi sori ẹrọ
You can download and install the CIMC 4.3(5.250030) Firmware M6 Common Update Patch via either of the following ways:
- Downloading and Installing via SWU
- Downloading and Installing via ISO
Downloading and Installing via SWU
Gba lati ayelujara
To download the common update patch file, pari awọn igbesẹ wọnyi:
- Wọle si Cisco Software Central, https://software.cisco.com.
- Ni agbegbe Gbigba lati ayelujara ati Igbesoke, yan Awọn igbasilẹ Wiwọle.
- Tẹ Awọn atupale Nẹtiwọọki Aabo ni Yan apoti wiwa Ọja kan.
- Yan awoṣe ohun elo lati atokọ jabọ-silẹ, lẹhinna tẹ Tẹ.
- Under Select a Software Type, choose Secure Network Analytics Patches, then choose Firmware > Firmware in the All Release area to locate the patch.
- Gbaa lati ayelujara ati fipamọ file, patch-common-SNA-FIRMWARE-20250403-v201.swu.
Fifi sori ẹrọ
To install the common update patch update file, pari awọn igbesẹ wọnyi:
- Wọle si Alakoso.
- On the Network Analytics page, choose Configure > Global > Central Management.
- Tẹ Oluṣakoso imudojuiwọn.
- On the Update Manager page, click Upload, and then open the saved file, patchcommon-SNA-FIRMWARE-20250403-v2-01.swu.
- Tẹ akojọ aṣayan Awọn iṣẹ fun ohun elo, lẹhinna tẹ Fi sori ẹrọ Imudojuiwọn.
The patch stops the Vertica Database, then restarts the appliance. - Make sure you restart Vertica on any Data Node after the update patch file successfully installs on all Data Nodes.
a. Log in to the Manager.
b. Go to Central Management > Data Store > Database Control.
c. Under the Database Control tab, click the (Ellipsis) icon in the Actions column for the database.
d. Choose Start.
e. Confirm the database status is shown as Connected. The installation process can take up to 90 minutes; the appliance restarts automatically.
Downloading and Installing via ISO
Gba lati ayelujara
To download the update patch file, pari awọn igbesẹ wọnyi:
- Wọle si Cisco Software Central, https://software.cisco.com.
- Ni agbegbe Gbigba lati ayelujara ati Igbesoke, yan Awọn igbasilẹ Wiwọle.
- Tẹ Awọn atupale Nẹtiwọọki Aabo ni Yan apoti wiwa Ọja kan.
- Yan awoṣe ohun elo lati atokọ jabọ-silẹ, lẹhinna tẹ Tẹ.
- From the left menu, choose All Release > 4.3 > 4.3(5.250030).
- Gbaa lati ayelujara ati fipamọ file, patch-common-SNA-FIRMWARE-20250403-M6REL.iso.
- There are two ways of installing ISO:
o Installation Using vKVM-Mapped vDVD
o Installation Using CIMC-Mapped vDVD
Ṣaaju fifi sori
If you have firewall rules enabled for Cisco Integrated Management Controller (CIMC), specify 169.254.254.2 in the list of allowed hosts to ensure the update is successful. Otherwise you can skip this step and go to Installation Using vKVM-Mapped vDVD or Installation Using CIMC-Mapped vDVD, depending on your preferred installation method.
- Log in to the unit’s Cisco Integrated Management Controller (CIMC) interface using a web kiri ayelujara.
- Choose Networking > Network Security.
- In the IP Filtering (Allow Listing) menu, enter 169.254.254.2 IP value in the IP filter field.
- Tẹ Fipamọ Awọn ayipada.
Installation Using vKVM-Mapped vDVD
This installation method updates the firmware by accessing the firmware update ISO file stored on the machine used to connect to the CIMC UI.
To install the firmware patch from an ISO image, use the vKVM console of an M6 machine.
- Log in to the unit’s Cisco Integrated Management Controller (CIMC) interface using a web kiri ayelujara.
- Select Launch KVM on the toolbar, if prompted, select HTML based KVM.
- The Virtual Console opens in a new browser tab.
- From the vKVM console, select Virtual Media to check for existing mappings. If any mappings exist (either vKVM-Mapped or CIMC-Mapped), eject them.
Wo example below for an old mapping to eject.
The next image shows the screen when no mappings are configured.
- From the vKVM console, select Virtual Media > vKVM-Mapped vDVD from the menu on the left side of the window to open the Map Virtual Media – CD/DVD dialog.
- In the Map Virtual Media – CD/DVD dialog box, browse to the locally stored SNA M6 appliance firmware ISO file, select it, and click Map Drive to map the local ISO to the SNA M6 appliance virtual drive.
- From the vKVM console, click Virtual Media from the menu on the left side of the window to verify that the ISO is mapped.
- Select Macros > Static Macros > CTRL-ALT-DEL to initiate the reboot process.
- Press the F6 key on your keyboard when the Cisco logo and boot messages appear in the vKVM console.
- When the Please select boot device: dialog box appears, select Cisco vKVMMapped vDVD2.00.
The firmware update initiates. The CIMC may reboot during the update process, causing a temporary loss of connection. If this occurs, log in to the CIMC again and re-launch the vKVM Console to continue monitoring the update. Once the firmware update is complete, the ISO will be ejected or unmounted, and the SNA appliance will reboot. - Verify on the CIMC Chassis Summary page that the firmware has been updated.
Installation Using CIMC-Mapped vDVD
This installation method updates the firmware by accessing the firmware update ISO file stored on an HTTP/S server accessible from the CIMC.
To install the firmware patch from an ISO image, use the vKVM console on the M6 machine.
- Log in to the unit’s Cisco Integrated Management Controller (CIMC) interface using a web kiri ayelujara.
- Select Launch KVM on the toolbar, if prompted, select HTML based KVM.
A new browser tab opens for the virtual KVM console, displaying a list of menu items on the left side of the window.
- From the vKVM console, select Virtual Media to check for existing mappings. If any mappings exist (either vKVM-Mapped or CIMC-Mapped), eject them.
Wo example below for an old mapping to eject.
The next image shows the screen when no mappings are configured.
- From the vKVM console, select Virtual Media > CIMC-Mapped vDVD from the menu on the left side of the window to open the Map Virtual Media – CD/DVD dialog.
- In the Map Virtual Media – CD/DVD dialog box, complete the following steps:
a. In the Name field, enter a descriptive name (for example, Firmware_ 2025).
b. Nínú File Location field, enter the path to the ISO file.
c. If required, enter the Username and Password.
d. Click Map Drive. - From the vKVM console, click Virtual Media to verify that the mapping is in effect.
- From the vKVM console, select Macros > Static Macros > Ctrl-Alt-Del to initiate the reboot process.
- Press the F6 key on your keyboard when the Cisco logo and boot messages appear in the vKVM console.
- When the Please select boot device: dialog box appears, select Cisco CIMC-Mapped vDVD2.00.
The firmware update initiates. The CIMC may reboot during the update process, after which the firmware update will continue. A CIMC reboot will cause a temporary loss of connection. Log in to the CIMC again and relaunch the vKVM Console to monitor
the update progress.
After the firmware update is complete, the ISO will not be automatically unmapped. Be sure to manually unmap the ISO before performing another reboot. - In the vKVM console, after you see the message All files copied and verified, the ISO has been loaded and the firmware update begins. At this point, it is safe to eject or unmap the previously mapped firmware ISO.
- From the vKVM console, select Virtual Media and click the name of the previously configured mapping to eject or unmap it.
- Click Confirm to unmap the ISO file.
The firmware update continues, and the next reboot will start the SNA M6 appliance. - On the CIMC Chassis Summary page, verify that the firmware has been updated to the expected version.
Olubasọrọ Support
Ti o ba nilo atilẹyin imọ-ẹrọ, jọwọ ṣe ọkan ninu awọn atẹle:
- Kan si agbegbe Cisco Partner
- Olubasọrọ Cisco Support
o To open a case by web: http://www.cisco.com/c/en/us/support/index.html
o For phone support: 1-800-553-2447 (AMẸRIKA)
o For worldwide support numbers: www.cisco.com/en/US/partner/support/tsd_cisco_worldwide_contacts.html
Aṣẹ-lori Alaye
Sisiko ati aami Sisiko jẹ aami-išowo tabi aami-išowo ti a forukọsilẹ ti Sisiko ati/tabi awọn alafaramo rẹ ni AMẸRIKA ati awọn orilẹ-ede miiran. Si view akojọ kan ti Sisiko-iṣowo, lọ si yi URL: https://www.cisco.com/go/trademarks. Awọn aami-išowo ti ẹnikẹta mẹnuba jẹ ohun-ini ti awọn oniwun wọn. Lilo ọrọ alabaṣepọ ko tumọ si ibasepọ ajọṣepọ laarin Sisiko ati ile-iṣẹ miiran. (1721R)
© 2025 Cisco Systems, Inc. ati/tabi awọn alafaramo rẹ.
Gbogbo awọn ẹtọ wa ni ipamọ.
Awọn iwe aṣẹ / Awọn orisun
 |
CISCO CIMC Firmware M6 Update Patch for Secure Network Analytics [pdf] Itọsọna olumulo CIMC Firmware M6 Update Patch for Secure Network Analytics, M6 Update Patch for Secure Network Analytics, Update Patch for Secure Network Analytics, Patch for Secure Network Analytics, Secure Network Analytics |