XP Power Digital Programming

Ulwazi lweMveliso

Iinkcukacha

• Inguqulelo: 1.0
• Ukhetho:
  • IEEE488
  • I-LAN Ethernet (LANI 21/22)
  • ProfibusDP
  • RS232/RS422
  • RS485
  • i-USB

IEEE488
I-interface ye-IEEE488 ivumela unxibelelwano kunye nezixhobo eziqhagamshelwe kwinkqubo yebhasi ye-IEEE-488.

Ulwazi lokuSeta i-interface
Ukuseta ngokukhawuleza ujongano, lungisa idilesi ephambili yeGPIB usebenzisa iiswitshi 1…5. Gcina iiswitshi 6…8 kwindawo OFF.

Izalathisi ze-LED ze-Interface Converter

• I-ADDR ye-LED: Ibonisa ukuba isiguquli sikwimeko ekubhekiswe kuyo umphulaphuli okanye ikwimeko ekubhekiswe kuyo umntu othethayo.
• I-LED1 SRQ: Ibonisa xa umguquli eqinisekisa umgca we-SRQ. Emva kovavanyo lwe-serial, i-LED iyaphuma.

Idilesi engundoqo ye-GPIB (PA)
Idilesi yeprayimari ye-GPIB (PA) isetyenziselwa ukuchonga iiyunithi eziqhagamshelwe kwinkqubo yebhasi ye-IEEE-488. Iyunithi nganye kufuneka ibe nePA eyodwa eyabelweyo. I-PC elawulayo iqhele ukuba ne-PA=0, kwaye iiyunithi ezidityanisiweyo zihlala zinedilesi ukusuka ku-4 ukuya phezulu. I-PA emiselweyo yonikezelo lwamandla lwe-FuG yi-PA=8. Ukunyenyisa i-PA, khangela iiswitshi zoqwalaselo kwiphaneli yangasemva yesixhobo se-IEEE-488 semodyuli yokuguqula ujongano. Akukho mfuneko yokuvula unikezelo lwamandla. Emva kokutshintsha ukutshintshwa koqwalaselo, cima unikezelo lwamandla kwimizuzwana emi-5 uze uyivule kwakhona ukuze usebenzise utshintsho. Iiswitshi zilandela inkqubo yokubini ukujongana. Umzekeloample, ukuseta idilesi ukuya ku-9, tshintsha 1 inexabiso le-1, i-2 inexabiso le-2, i-3 inexabiso le-4, i-4 inexabiso le-8, kwaye i-5 inexabiso le-16. Isixa samaxabiso otshintsho kwindawo ye-ON inika idilesi. Iidilesi kuluhlu 0…31 ziyenzeka.

IMowudi yokuNhambelana Probus IV
Ukuba ukuhambelana nenkqubo yangaphambili yeProbus IV iyadingeka, i-converter interface inokusetwa kwimodi yokuhambelana ekhethekileyo (iMode 1). Nangona kunjalo, le mowudi ayikhuthazwa kuyilo olutsha. Ukusebenza ngokupheleleyo kwenkqubo entsha yeProbus V inokufumaneka kuphela kwimodi eqhelekileyo.

I-LAN Ethernet (LANI 21/22)
Xa ucwangcisa inkqubo yolawulo lwesixhobo esitsha, kuyacetyiswa ukuba usebenzise i-TCP/IP kunxibelelwano. I-TCP / IP iphelisa imfuno yabaqhubi abongezelelweyo.

I-Ethernet

• I-10 / 100 Base-T
• RJ-45 isinxibelelanisi

IFayibha Optic Transmitter (Tx)

• Ikhonkco lesalathisi se-LED

IFiber Optic Receiver (Rx)

• Umsebenzi wesalathisi se-LED

FAQ

• Ndiyilungisa njani idilesi yokuqala (PA) yesixhobo?
  Ukunyenyisa idilesi engundoqo, fumana iiswitshi zoqwalaselo kwiphaneli yangasemva yesixhobo se-IEEE-488 semodyuli yokuguqula ujongano. Cwangcisa utshintsho ngokwenkqubo yokubini, apho utshintsho ngalunye lunexabiso elithile. Isixa samaxabiso otshintsho kwindawo ye-ON inika idilesi. Cima unikezelo lwamandla kwimizuzwana emi-5 uze uphinde uyivule kwakhona ukuze usebenzise utshintsho.
• Yeyiphi idilesi esisiseko esisiseko (PA) yobonelelo lwamandla lwe-FuG?
  Idilesi esisiseko esisiseko yonikezelo lwamandla e-FuG yi-PA=8.
• Ndingafezekisa njani ukuhambelana nenkqubo yangaphambili yeProbus IV?
  Ukufezekisa ukuhambelana nenkqubo yangaphambili yeProbus IV, misela i-converter interface kwimodi yokuhambelana (iMode 1). Nangona kunjalo, ayikhuthazwa kuyilo olutsha njengoko ukusebenza ngokupheleleyo kwenkqubo entsha yeProbus V inokufezekiswa kuphela kwimodi eqhelekileyo.

PHEZULUVIEW

• Imodyuli ye-ADDAT ye-30/31 yi-interface ye-AD / DA yokulawula ukunikezelwa kwamandla nge-fiber optics usebenzisa i-serial data transmission. Ibhodi yolwandiso ye-ADDAT ixhonywe ngqo kwisixhobo sombane.
• Isiguquli sokuguqula isignali yojongano ukuya kwisignali yefiber optics efakwe kwindawo yolawulo yangasemva. Ukufikelela kukhuseleko lwengxolo ephezulu enokwenzeka, isiguquli somqondiso sinokusebenza njengemodyuli yangaphandle ngaphandle konikezelo lwamandla. Kwimeko apho ugqithiso lwedatha ngaphandle konikezelo lwamandla luyenzeka nangefiber optics.

Le ncwadana yenziwe ngu: XP Power FuG, Am Eschengrund 11, D-83135 Schechen, Germany

IEEE488

I-Pin isabelo-IEEE488

Ulwazi lokuseta ujongano

ICEBISO: Ukuseta okukhawulezayo: Ngesiqhelo, kuphela idilesi yokuqala yeGPIB ekufuneka ihlengahlengiswe kwiiswitshi 1…5. Ezinye iiswitshi 6…8 zihlala zikwimo OFF.

Izalathisi ze-LED ze-Interface Converter

• I-ADDR ye-LED
  Le LED ilayitiwe, ngelixa isiguquli sikwimo ekubhekiswe kuyo umphulaphuli okanye kwisimo somntu othetha naye.
• I-LED1 SRQ
  Le LED ivuliwe, ngelixa isiguquli siqinisekisa umgca we-SRQ. Emva kovavanyo lwe-serial, i-LED iyaphuma.

Idilesi engundoqo ye-GPIB (PA)

• Idilesi yokuqala ye-GPIB (PA) yenza ukuba kuchongwe zonke iiyunithi eziqhagamshelwe kwinkqubo yebhasi ye-IEEE-488.
• Ke ngoko, i-PA eyodwa kufuneka inikwe iyunithi nganye ebhasini.
• I-PC elawulayo idla ngokuba ne-PA=0 kwaye iiyunithi ezidityanisiweyo zihlala zinedilesi ukusuka kwi-4 ukuya phezulu. Ngokubanzi, imeko yonikezelo lonikezelo lwamandla lwe-FuG yi-PA=8.
• Ukulungelelaniswa kwePA kwenziwa kwiphaneli yangasemva yesixhobo kwimodyuli ye-IEEE-488 yokuguqula ujongano. Akuyimfuneko ukuvula unikezelo lwamandla.
• Emva kokutshintsha ukutshintshwa kohlengahlengiso, ukunikezelwa kwamandla kufuneka kucinywe imizuzwana emi-5 kwaye kutshintshe kwakhona ukuze kusetyenziswe utshintsho.

IMowudi yokuNhambelana Probus IV

• Ukuba ukuhambelana nenkqubo yangaphambili yeProbus IV kuyimfuneko, i-converter interface inokusetwa kwimodi ehambelanayo ekhethekileyo (iMode 1).
• Le mowudi ayikhuthazwa kuyilo olutsha.
• Ukusebenza ngokupheleleyo kwenkqubo entsha yeProbus V inokufumaneka kuphela kwimodi eqhelekileyo!

I-LAN Ethernet (LANI 21/22)

Kwimeko yeprogram yesicelo esitsha sokulawula isixhobo kucetyiswa ukuba usebenzise i-TCP / IP yokunxibelelana. Ngokusebenzisa i-TCP/IP, akukho baqhubi bongezelelweyo bafunekayo.

I-Pin assignment – ​​LAN Ethernet (LANI 21/22)

Ulawulo oluthe ngqo nge-TCP/IP

• Ukuseta uqhagamshelo kunye noqwalaselo
  Ngokuxhomekeke kwinethiwekhi yakho, ezinye iisetingi kufuneka zenziwe. Okokuqala, uqhagamshelo kwisiguquli sojongano kufuneka lusekwe. Kule nto, idilesi ye-IP kufuneka imiselwe. Indlela ecetyiswayo yokubona isixhobo kwiNethiwekhi kunye nokuchonga idilesi ye-IP yayo kukusebenzisa iNkqubo ethi "Lantronix Device Installer"
  ISILUMKO Qaphela xa udibanisa kwinethiwekhi yenkampani, kuba idilesi ye-IP engalunganga okanye ephindwe kabini ingabangela ingxaki enkulu kwaye ithintele ezinye iiPC ekungeneni kwinethiwekhi!
  Ukuba awuqhelananga nolawulo lwenethiwekhi kunye noqwalaselo, sincoma kakhulu ukuba wenze amanyathelo akho okuqala kwinethiwekhi ezimeleyo ngaphandle kokudibanisa kwinethiwekhi yakho yenkampani (uqhagamshelwano nge-CrossOver-cable)! Kungenjalo, nceda ucele uncedo kumlawuli wenethiwekhi yendawo!
• Faka iDeviceInstaller
  Ngokuxhomekeke kwinethiwekhi yakho, ezinye iisetingi kufuneka zenziwe.
  1. Khuphela inkqubo ye "Lantronix Device Installer" ukusuka www.lantronix.com kwaye uyiqhube.
  2. Emva koko Khetha ulwimi oluthandayo.
  3. Ngoku ijongiwe ukuba ingaba "iMicrosoft .NET Framework 4.0" okanye i-"DeviceInstaller" sele ifakiwe kwiPC yakho. Ukuba i-“Microsoft .NET Framework” ayikafakwa, iya kufakwa kuqala.
  4. Yamkela imigaqo yelayisensi "Microsoft .NET Framework 4.0".
  5. Ufakelo lwe "Microsoft .NET Framework 4.0" inokuthatha ukuya kwimizuzu engama-30.
  6. Ngoku ukufakela kufuneka kugqitywe nge "Gqiba".
  7. Emva koko ukufakwa kwe "DeviceInstaller" kuqala.
  8. Yamkela amaphepha awohlukeneyo ngo "Okulandelayo >".
  9. Khetha isiqulathi seefayili sakho sokuhlohla.
  10. Qinisekisa ukuba inkqubo iza kufakwa.
      Ngoku inkqubo "DeviceInstaller" ifakiwe.
• Ukufunyanwa kwesixhobo
  PHAWULA Le miyalelo ilandelayo ibhekisa kusetyenziso lukaMicrosoft Windows 10.
  1. Emva kokufakela, qalisa i-"DeviceInstaller" kwimenyu yokuqalisa yeWindows.
  2. Ukuba isilumkiso seWindows Firewall siyavela, cofa ku “Vumela ufikelelo”.
  3. Zonke izixhobo ezifunyenwe kwinethiwekhi ziya kuboniswa. Ukuba isixhobo esifunwayo asiboniswanga, unokuphinda uqalise ukukhangela ngeqhosha elithi “Khangela”.
  4. Idilesi ye-IP, kule meko 192.168.2.2, iyadingeka ukudibanisa kwisixhobo. Kuxhomekeke kubume bothungelwano, idilesi ye-IP inokutshintsha qho xa isixhobo sixhotyiswa. Emva kokuba ufumene idilesi ye-IP nge-DeviceInstaller uyakwazi ukudibanisa nesixhobo.
• Uqwalaselo nge web ujongano
  1. Kucetyiswa ukuba usebenzise a webumkhangeli zincwadi woqwalaselo.
     Chwetheza idilesi ye-IP yesixhobo sakho kwibar yedilesi kwaye ucofe u-Enter.
  2. Iwindow yokungena inokuboniswa, kodwa kufuneka ucofe kuphela "Kulungile". Ngokungagqibekanga, akukho nkcukacha zokungena ezifunekayo.
• Lungiselela imimiselo
  Idilesi ethile ye-IP yomthengi kunye ne-subnet mask inokusetwa kwindawo ethi "Sebenzisa i-IP elandelayo yoqwalaselo". Iidilesi ze-IP ezibonisiweyo / i-subnet mask zi-examples. "Fumana idilesi ye-IP ngokuzenzekelayo" kukuphela kwefektri.
• Izibuko leNdawo
  ISibuko seNdawo "2101" sisisiseko sefektri.
• Inkcukacha ezithe vetshe
  I-interface converter isekelwe kwisixhobo esifakwe kwi-Lantronix-X-Power. Uhlaziyo lomqhubi lweenkqubo ezintsha zokusebenza kunye nolwazi oluthe kratya lunokufumaneka: http://www.lantronix.com/device-networking/embedded-device-servers/xport.html

Profibus DP

I-Pin isabelo sojongano

UkuSetwa koNxibelelwano – GSD File
IGSD file ye-interface converter ibekwe kulawulo "Digital_Interface\ProfibusDP\GSD". Kuxhomekeke kuguqulelo lwemodyuli yokuguqula, nokuba yi-"PBI10V20.GSD" kufuneka isetyenziswe. Ukuba i file ayichanekanga, iyunithi yonikezelo lwamandla ayibonwa ngumphathi.

Ukusetwa koNxibelelwano – Ukusetwa kwedilesi yeNode
Idilesi yenodi ichonga iiyunithi (=iindawo) eziqhagamshelwe kwiProfibus. Idilesi eyodwa kufuneka yabelwe kuyo yonke indawo ebhasini. Idilesi isetiwe kunye nokutshintsha kwicala elingasemva le-interface converter. Izindlu zonikezelo lwamandla akufuneki zivulwe. Emva kwayo nayiphi na inguqu kuqwalaselo, unikezelo lwamandla (i-interface converter) kufuneka lutshintshwe od ubuncinane imizuzwana emi-5. Iidilesi zamakhoboka kuluhlu 1…126 ziyenzeka.

Iimpawu

• I-LED eluhlaza -> SERIAL Kulungile
• Le LED ivuliwe, ukuba i-serial fiber optic uxhumano phakathi kwemodyuli yesiseko ye-ADDAT kunye ne-interface converter isebenza ngokuchanekileyo.
• Ngexesha elifanayo, i-LED BUSY kwiphaneli yangaphambili yonikezelo lwamandla ngokuqhubekayo, ebonisa ukuhanjiswa kwedatha okuqhubekayo phakathi kwe-converter interface kunye ne-ADDAT imodyuli yesiseko.
• I-LED ebomvu -> IMPASO YEBHASI
• Le LED ivuliwe, ukuba akukho nxibelelwano kwi-ProfibusDP Master.

Indlela yokuSebenza

• I-ProfibusDP converter interface ibonelela ngebhloko yedatha ye-Byte ye-16 kunye nebhloko yedatha ye-16 Byte.
• Idatha engenayo evela kwiProfibus igcinwe kwibhloko yedatha yegalelo.
• Le bloko idluliselwa ngebhayisikile njengomtya we-hexadecimal wamagama angama-32 kwimodyuli yesiseko ye-ADDAT. (Bhalisa ">H0” ye-ADDAT 30/31)
• Imodyuli yesiseko se-ADDAT iphendula ngomtya we-hexadecimal wamagama angama-32.
• Lo mtya uqulethe i-16 Bytes yokubeka iliso kunye neempawu zesimo.
• I-Profibus interface converter igcina ezi 16 Bytes kwibhloko yedatha yemveliso, enokufundwa yi-Profibus master.
• Ixesha lomjikelo limalunga ne-35ms.
• Nceda ubhekiselele kwinkcazo yoBhaliso ">H0” kuxwebhu lweDigital Interfaces Command Reference ProbusV.

Iifomathi zomhla

Iinkcukacha ezithe xaxe
I-interface converter iProfibus DP isekelwe kwisiguquli esiqhelekileyo "UNIGATE-IC" esivela kwi-Deutschmann Automationstechnik (iphepha lemveliso). Zonke iireyithi eziqhelekileyo ze-Profibus baud ukuya kuthi ga kwi-12 MBit/s ziyaxhaswa. Iisetingi zoguqulelo zilawulwa ngokweskripthi kunye nexesha lomjikelo we-approx. 35ms.

RS232/422

Ulwazi lokuseta ujongano
Isixhobo ngasinye esixhotyiswe nge-RS232, okanye i-RS422 yangaphakathi okanye i-converter yangaphandle, inokulawulwa kude ngePC phezu kwe-COM port. Isuka e view yoMdwelisi wesicelo, akukho mahluko phakathi kwezi ntlobo zahlukeneyo.

I-RS232, isiguquli sojongano lwangaphandle

• Umbane uqhagamshelwe kwi-pc ngePlastiki Optic Fiber link (POF). Oku kuqinisekisa ukhuseleko lwengxolo ephezulu enokwenzeka.
• Umgama wekhonkco ophezulu yi-20m.
• Kwicala lePC, i-converter interface ixhunywe ngokuthe ngqo kwi-port ye-COM eqhelekileyo. Isignali ye-interface ye-Tx isetyenziselwa ukunika amandla umguquli, ngoko akukho nikezelo lwangaphandle olufunekayo.

Uqhagamshelo lweFayibha optic:

• Imveliso yedatha yomguquli ("T", Transmit) kufuneka idibaniswe kwigalelo ledatha ("Rx", Yamkela) yokunikezelwa kwamandla.
• Igalelo ledatha ye-converter ("R", Yamkela) kufuneka idibaniswe kwimveliso yedatha ("T", Transmit) yokunikezelwa kwamandla.

I-Pin assignment – ​​RS232, umfundi oqeqeshwayo

Ukuseka uxhumano kwi-PC eqhelekileyo kwanele ukudibanisa izikhonkwane ze-2, i-3 kunye ne-5 kunye nee-PIN ezifanayo kwi-PC com port.
Iintambo eziqhelekileyo ze-RS-232 ezine-1: i-pin ye-1 yokudibanisa ziyacetyiswa.

ISILUMKO Kukho iintambo ze-NULL-modem ezikhoyo kunye nezikhonkwane ze-2 kunye ne-3 ezinqamlezileyo. Iintambo ezinjalo azisebenzi.

I-Pin assignment – ​​RS422

ISILUMKO I-asayinimenti yephini ilandela i-quasi-standard. Ke ngoko, ayinakuqinisekiswa, ukuba isabelo se-pin siyahambelana nemveliso yakho ye-PC RS-422. Kwimeko yamathandabuzo, isabelo se-pin sePC kunye nesiguquli sojongano kufuneka siqinisekiswe.

RS485

RS485 Ulwazi olungasemva

• I-"RS485 Bus" idityaniswa kakhulu nenkqubo yebhasi ye-2 elula esetyenziselwa ukudibanisa amakhoboka amaninzi anedilesi ngesixhobo esiyintloko (oko kukuthi iPC).
• Ichaza kuphela amanqanaba omqondiso kumaleko wonxibelelwano womzimba.
• I-RS485 ayichazi nayiphi na ifomati yedatha, okanye nayiphi na iprotocol okanye i-asayinimenti yesiqhagamsheli sesiqhagamshelo!
• Ke ngoko, wonke umenzi wezixhobo zeRS485 ukhululekile ngokupheleleyo ekuchazeni ukuba iiyunithi ezikwibhasi yeRS485 zinxibelelana njani.
• Oku kubangela ukuba iiyunithi ezingafaniyo ezivela kubavelisi abahlukeneyo zihlala zingasebenzi kunye ngokuchanekileyo. Ukwenza ukuba iiyunithi ezihlukeneyo zisebenze kunye, imigangatho entsonkothileyo efana neProfibusDP yaziswa. Le migangatho isekelwe
• RS485 kumaleko womzimba, kodwa ikwachaza unxibelelwano kumanqanaba aphezulu.

I-Interface Converter RS232/USB ukuya kwi-RS485

• I-PC ene-interface ye-RS232 / USB eqhelekileyo inokuhlengahlengiswa kwi-RS485 ngabaguquli be-interface abakhoyo kwimarike.
• Ngesiqhelo, aba baguquli basebenza kakuhle kwimowudi epheleleyo ye-duplex (izibini ezi-2 zeengcingo).
• Kwimowudi ye-half duplex (i-1 pair of wires), umthumeli wesikhululo ngasinye kufuneka angasebenzi ngokukhawuleza emva kokuba i-byte yokugqibela ithunyelwe ukucima ibhasi kwidatha elandelayo elindelekileyo.
• Kwii-RS232 ezininzi ezifumanekayo - i-RS485 i-interface converters i-transmitter ilawulwa ngophawu lwe-RTS. Olu setyenziso lukhethekileyo lwe-RTS aluxhaswanga ngabaqhubi besoftware eqhelekileyo kwaye ifuna isoftware ekhethekileyo.

I-Pin assignment – ​​RS485

I-RS485 ayichazi nasiphi na isabelo sephini. Isabelo sezikhonkwane sihambelana neenkqubo eziqhelekileyo. Ngokunokwenzeka, isabelo se-pin kwicala lePC okanye ezinye izixhobo ziya kuba diderent!

Ubumbeko – Idilesi

• Idilesi engu-0 yinkqubo emiselweyo yomzi-mveliso.
• Ukuba ngaphezulu kwesixhobo esinye sidityaniswe kunye nge-RS485, iidilesi ezikhethwayo zinokusetwa njengommiselo womzi-mveliso. Xa kunjalo, nceda uqhagamshelane XP Power.
• Kwimeko yokusetyenziswa okuqhelekileyo, ukutshintsha iidilesi zezixhobo ngoko akuyimfuneko.
• Imo yolungelelaniso kufuneka ivulwe ukuze utshintshe idilesi yesixhobo.
• Ukusebenza kwemowudi yokulinganisa kwenziwa ngomngcipheko wakho! Ukuze kube njalo, isixhobo kufuneka sivulwe ekufuneka senziwe ngabasebenzi abaqeqeshiweyo kuphela! Imimiselo yokhuseleko yangoku kufuneka yaneliswe!

Ulwakhiwo lweNethiwekhi kunye nokupheliswa

• Ibhasi kufuneka ibe nesakhiwo somgca kunye ne-120 Ohm yokuphelisa i-resistors kuzo zombini iziphelo. Kwimowudi yesiqingatha se-duplex, i-120 Ohm resistor phakathi kwePins 7 kunye ne-8 ingasetyenziselwa le njongo.
• I-topology yeenkwenkwezi okanye iingcingo zesebe ezinde kufuneka ziphetshwe ukuthintela ukuthotywa komqondiso ngenxa yokubonakalisa.
• Isixhobo esiyintloko sinokufumaneka naphi na ngaphakathi ebhasini.

Imowudi ye-Fullduplex (yahluliwe i-Rx kunye ne-Tx)

• Ibhasi iqulathe izibini zeengcingo ezi-2 (iingcingo ezi-4 zesignali kunye ne-GND)
• Ixesha: Ixesha lokuphendula lemodyuli ye-ADDAT ingaphantsi kakhulu kwe-1ms (ngokuqhelekileyo i-100us embalwa). Inkosi kufuneka ilinde ubuncinci i-2ms emva kokufumana ibhayithi yokugqibela yomtya wempendulo phambi kokuba iqalise ukuthumela umtya womyalelo olandelayo. Ngaphandle koko, ukungqubana kwedatha kwibhasi kunokwenzeka.

IHalf duplex Operation (i-Rx kunye ne-Tx zidityaniswe kwiperi enye yocingo)

• Ibhasi ine 1 wire pair (2 iingcingo zomqondiso kunye neGND)
• Ixesha 1: Ixesha lokuphendula lemodyuli ye-ADDAT ingaphantsi kakhulu kwe-1ms (ngokuqhelekileyo i-100us embalwa). Inkosi kufuneka ikwazi ukutshintsha i-od transmitter yayo ngaphakathi kwe-100us emva kokuba i-byte yokugqibela idluliselwe.
• Ixesha 2: I-transmitter yekhoboka (i-Probus V RS-485 interface) ihlala isebenza ubuninzi be-2ms emva kokuba i-byte yokugqibela idluliselwe kwaye imiselwe kwi-impedance ephezulu emva koku. Inkosi kufuneka ilinde ubuncinci i-2ms emva kokufumana ibhayithi yokugqibela yomtya wempendulo phambi kokuba iqalise ukuthumela umtya womyalelo olandelayo.
• Ukwaphula le miqobo yexesha kukhokelela kungquzulwano lwedatha.

i-USB

I-pin assignment – ​​USB

Ukuhlohla
Ujongano lwe-USB lusebenza kunye nesoftware yomqhubi njengechweba le-COM elibonakalayo. Ngoko ke, kulula ukucwangcisa unikezelo lwamandla ngaphandle kolwazi olukhethekileyo lwe-USB. Unokusebenzisa isoftware esele isebenze ukuza kuthi ga ngoku ngechweba lokwenyani leCOM.
Nceda usebenzise ufakelo lomqhubi file ukusuka XP Power Terminal package.

Ufakelo loMqhubi oluzenzekelayo

1. Qhagamshela unikezelo lwamandla kwiPC ngentambo ye-USB.
2. Ukuba kukho uqhagamshelo lwe-intanethi olukhoyo, Windows 10 iya kuthi cwaka iqhagamshela kuHlaziyo lweWindows webindawo kwaye ufake nawuphi na umqhubi ofanelekileyo awufumanayo kwisixhobo.
   Ukuhlohla kugqityiwe.

Ufakelo ngolungiselelo oluphunyeziweyo file

1. CDM21228_Setup.exe ephunyeziweyo ibekwe kwiXP Power Terminal download packet.
2. Cofa ekunene kwi ephunyeziweyo kwaye ukhethe "All extrahieren..."
3. Yenza okuphunyeziweyo njengomlawuli kwaye ulandele imiyalelo.
4. 
5. 
6. 

Nje ukuba ukufakela kugqityiwe, nqakraza "ukugqiba".

Isihlomelo

Uqwalaselo

• Ireyithi yeBaud
  Umlinganiselo weBaud omiselweyo wezixhobo ezine:
  • Ujongano lwe-USB lumiselwe kwi-115200 Baud.
    Iqondo eliphezulu le-baud ye-USB yi-115200 Baud.
  • I-interface ye-LANI21/22 imiselwe kwi-230400 Baud.
    Umlinganiselo we-baud ophezulu we-LANI21/22 yi-230k Baud.
  • Ujongano lweRS485 lumiselwe kwi-9600 Baud.
    Ubuninzi bezinga le-baud kwi-RS485 yi-115k Baud.
  • RS232/RS422 interface isetelwe 9600 Baud.
    Ubuninzi bezinga le-baud kwi-RS485 yi-115k Baud.

Isixokeleli
Unobumba wokuphelisa "LF" yinto engagqibekanga yasefektri.

Ugunyaziso

1. Ngaphambi kokuba kuqaliswe ukugunyaziswa kojongano, umbane weDC kufuneka ucinywe.
2. Ujongano lwekhompyuter yolawulo kufuneka ludityaniswe kujongano lombane weDC njengoko kuchaziwe.
3. Ngoku vula iswitshi YAMANDLA.
4. Cinezela i-REMOTE iswitshi (1) kwiphaneli engaphambili ukuze i-LED YOKUNGENZIWA (2) icime. Ukuba ujongano olongezelelweyo lwe-analog lukhona, cwangcisa iswitshi (6) kwiDIGITAL. I-DIGITAL LED (5) ikhanyisa.
5. Qala isoftware yakho yokusebenza kwaye usete uqhagamshelo kujongano kwisixhobo. Isixhobo ngoku silawulwa ngesoftware esebenzayo. I-BUSY LED (4) ikhanyisa ngokukhawuleza ngexesha lokuhamba kwedatha ngeenjongo zokubeka iliso. Ulwazi olungaphaya malunga nemiyalelo kunye nemisebenzi inokufumaneka kuxwebhu lweDigital Interface Command Reference Reference Probus V.

Ukutshintshela ngokukhuselekileyo i-o: unikezelo lwamandla, qhubeka ngolu hlobo lulandelayo:
Loo nkqubo iyimfuneko ngokupheleleyo ngenxa yezizathu zokhuseleko. Oku kungenxa yokuba ukukhutshwa kwemveliso voltagu-e usengaqwalaselwa kumqulutage bonisa. Ukuba iyunithi itshintshiwe o: ngokukhawuleza usebenzisa i-AC Power switch, nayiphi na ivolthi eyingozitagi ekhoyo (umzekelo iicapacitors ezihlawulisiweyo) ayinakuboniswa njengoko umboniso ujikisiwe o:.

1. Nge-software yokusebenza, ii-setpoints kunye nezangoku zisetelwe kwi-"0" kwaye emva koko imveliso icinyiwe.
2. Emva kokuba imveliso ingaphantsi kwe- <50V, vula iyunithi ngokupheleleyo usebenzisa i-POWER (1) yokutshintsha. Nika ingqalelo kumandla ashiyekileyo kwisicelo sakho!
   Umbane weDC ucinyiwe.

Iingozi zokusetyenziswa kakubi kwenkqubo yedijithali

• Ingozi yokutshatyalaliswa kombane kwiziphumo zamandla!
  • Ukuba i-digital interface cable itsalwa ngexesha lesixhobo esisebenza kwimodi ye-DIGITAL, iziphumo zesixhobo ziya kugcina ixabiso lokugqibela lokumisela!
  • Xa utshintshela kwimodi ye-DIGITAL ukuya kwimodi ye-LOCAL okanye ye-ANALOG, iziphumo zesixhobo ziya kugcina ixabiso lokugqibela elisetyenzisiweyo nge-interface yedijithali.
  • Ukuba unikezelo lwe-DC lujikisiwe nge-od ngokutshintsha AMANDLA okanye nge-outage yomqulutage unikezelo, amaxabiso acwangcisiweyo aya kucwangciswa ku-"0" xa isixhobo siqaliswa ngokutsha.

Ukuvavanya umdibaniso: NI IEEE-488

Ukuba usebenzisa iiplagi zeSizwe ze-IEEE-488 kwikhadi kwiPC yakho, uqhagamshelwano lunokuvavanywa ngokulula kakhulu. Ikhadi lihanjiswa kunye neprogram: "Umlinganiselo weSizwe weZixhobo kunye ne-Automation Explorer". Ifom emfutshane: "NI MAX". Isetyenziselwa le ex ilandelayoample.

PHAWULA Abanye abavelisi beebhodi ze-IEEE-488 kufuneka babe neenkqubo ezifanayo. Nceda ubhekisele kumenzi wekhadi lakho.

Example for NI MAX, Version 20.0

1. Qhagamshela unikezelo lwamandla lwe-FuG kwiPC nge-IEEE-488.
2. Qala i-NI MAX kwaye ucofe ku-“Geräte und Schnittstellen” kunye “GPIB0”.
3. Ngoku cofa ku "Scan for Instruments". Ukunikezelwa kwamandla kuya kuphendula nge "FuG", Uhlobo kunye nenombolo ye-serial.
4. Cofa ku-“Kommunikation mit Gerät”: Ngoku ungachwetheza umyalelo kwindawo ethi “Thumela”: Emva kokuqalisa isinxibelelanisi, umtya “*IDN?” sele ibekwe kwindawo yongeniso. Lo ngumbuzo osemgangathweni womtya wokuchonga wesixhobo.
   Ukuba ucofa ku-"QUERY" indawo ethi "Thumela" igqithiselwa kumbane kwaye umtya wempendulo uboniswa kwindawo ethi "Umtya owamkelweyo".
   Ukuba ucofa kwi-"BHALA", indawo ethi "Thumela" ithunyelwa kumbane, kodwa umtya wempendulo awuqokelelwa kumandla ombane.
   Ukucofa ku-"FUNDA" kuqokelela kwaye kubonise umtya wempendulo.
   (“UMBUZO” yindibaniselwano nje ethi “BHALA” kunye “FUNDA”.)
5. Cofa ku-“QUERY”:
   Uhlobo lwemveliso yonikezelo lwamandla kunye nenombolo yesiriyali.

Ukuvavanya uxhulumaniso: XP Power Terminal
Inkqubo ye-XP Power Terminal ingasetyenziselwa ukuvavanya uxhulumaniso kwiyunithi yonikezelo lwamandla. Oku kunokukhutshelwa kwithebhu yeZibonelelo kwiphepha ngalinye lemveliso yeXP Power Fug.

Unxibelelwano olulula exampLes

IEEE488
Ukuqhagamshela isixhobo, phantse nayiphi na inkqubo ye-terminal ingasetyenziswa.

ProfibusDP

• Umqulutage misela ixabiso
  Ibhlokhi yedatha yegalelo 0 (=LSB) kunye ne-Byte 1 (=MSB)
  0…65535 iziphumo ku-0…umthamo oqhelekileyotage.
  Kunikezelo lwamandla e-bipolar ixabiso elibekiweyo linokuguqulwa ngokucwangcisa i-Byte4/Bit0.
• Ixabiso leseti yangoku
  Ibhlokhi yedatha yegalelo 2 (=LSB) kunye ne-Byte 3 (=MSB)
  0…65535 iziphumo ku-0...nominal current.
  Kunikezelo lwamandla e-bipolar ixabiso elibekiweyo linokuguqulwa ngokucwangcisa i-Byte4/Bit1.
• Khupha imveliso voltage
  INGOZI Ngokuthumela ibhloko yokufaka etshintshileyo (bhalisa "> BON") imveliso iyasebenza ngokukhawuleza!
  Ibhloko yedata yokufaka i-Byte 7, Bit 0
  Imveliso yonikezelo lwamandla ikhutshwa ngekhompyutha kwaye itshintshiwe od.
• Funda umva wesiphumo voltage
  Ibhlokhi yedatha yemveliso i-Bytes 0 (=LSB) kunye ne-Byte 1 (=MSB)
  0…65535 iziphumo ku-0…umthamo oqhelekileyotage.
  Uphawu lwexabiso lukwi-Byte4/Bit0 (1 = mbi)
• Funda ngasemva kwimveliso yangoku
  Ibhlokhi yedatha yemveliso i-Bytes 2 (=LSB) kunye ne-Byte 3 (=MSB)
  0…65535 iziphumo ku-0...nominal current.
  Uphawu lwexabiso lukwi-Byte4/Bit1 (1 = mbi)

Iseti yomyalelo kunye nokucwangcisa

Ukuze kugqitywe ngokupheleleyoview yeerejista ezinemiyalelo eyongezelelweyo kunye nemisebenzi ibhekiselele kuxwebhu lweDigital Interfaces Command Reference Probus V. Iyunithi yonikezelo lwamandla ilawulwa ngemiyalelo elula ye-ASCII. Ngaphambi kokuhambisa umyalelo omtsha, impendulo ehambelana nomyalelo wangaphambili kufuneka ilindelwe kwaye ihlolwe ukuba iyimfuneko.

• Umtya ngamnye womyalelo kufuneka upheliswe ubuncinane ngonobumba omnye wabalandelayo okanye nayiphi na indibaniselwano yabo: “CR”, “LF” okanye “0x00”.
• Umtya ngamnye womyalelo othunyelwe kwiyunithi yonikezelo lwamandla uya kuphendulwa ngomtya ohambelanayo wokuphendula.
• Imitya yomyalelo “engenanto”, oko kukuthi, iintambo eziquka oonobumba bokuphelisa kuphela, ziyakhatywa kwaye aziwubuyiseli umtya wempendulo.
• Yonke idatha efundiweyo kunye neentambo zokuxhawula izandla ezivela kwiyunithi yonikezelo lwamandla ziyayekiswa ngesiterminali esiseti (jonga irejista ">KT" okanye "> CKT" kunye no "Y" umyalelo)
• Ukufumana ixesha lokuvala: Ukuba akukho mbhalo omtsha ufunyenweyo ngaphezulu kwe-5000ms zonke iimpawu ezifunyenwe ngaphambili ziya kulahlwa. Ngenxa yexesha elide ngokwentelekiso, kuyenzeka ukuthumela imiyalelo ngesandla usebenzisa inkqubo ye-terminal.
• Ubude bomyalelo: Obona bude buphezulu bomtya womyalelo bukhawulelwe kumagama angama-50.
• Fumana i-buffer: I-ADDAT inamagama angama-255 ubude be-FIFO Fumana i-Buffer.

Amaxwebhu / Izibonelelo

XP Power Digital Programming [pdf] Incwadi Yomyalelo INkqubo yeDijithali, iNkqubo

Iimbekiselo

• Incwadi yokusebenzisa