XP Power Digital Programming

Cov ntaub ntawv khoom

Specifications

• Version: 1.0
• Kev xaiv:
  • IEEE 488
  • LAN Ethernet (LANI 21/22)
  • ProfibusDP
  • RS232/RS422
  • TSI RS485
  • USB

IEEE 488
IEEE488 interface tso cai rau kev sib txuas lus nrog cov cuab yeej txuas nrog IEEE-488 tsheb npav.

Interface Setup Information
Txhawm rau teeb tsa lub interface sai, kho GPIB thawj qhov chaw nyob siv keyboards 1…5. Khaws cov keyboards 6…8 hauv OFF txoj haujlwm.

Interface Converter LED Qhov taw qhia

• LED ADDR: Qhia seb tus converter puas nyob hauv lub xeev uas tus neeg hais nyob hauv lub xeev lossis tus neeg hais lus hais hauv lub xeev.
• LED 1 SRQ: Qhia thaum lub converter lees paub SRQ kab. Tom qab qhov kev ntsuam xyuas serial, LED tawm mus.

GPIB Primary Address (PA)
GPIB thawj qhov chaw nyob (PA) yog siv los txheeb xyuas cov chaw txuas nrog IEEE-488 lub tsheb npav. Txhua chav tsev yuav tsum muaj PA tshwj xeeb. Cov tswj PC feem ntau muaj PA = 0, thiab cov chav sib txuas feem ntau muaj qhov chaw nyob ntawm 4 nce mus. Lub neej ntawd PA rau FuG cov khoom siv hluav taws xob yog PA = 8. Txhawm rau kho PA, nrhiav cov kev teeb tsa hloov pauv ntawm lub vaj huam sib luag tom qab ntawm lub cuab yeej IEEE-488 interface converter module. Tsis tas yuav qhib lub hwj chim. Tom qab hloov qhov hloov pauv, tua lub hwj chim rau 5 vib nas this thiab tom qab ntawd tig rov qab los siv qhov hloov pauv. Cov keyboards ua raws li binary system rau qhov chaw nyob. Rau example, los teeb qhov chaw nyob rau 9, hloov 1 muaj nqi ntawm 1, hloov 2 muaj nqi ntawm 2, hloov 3 muaj nqi 4, hloov 4 muaj nqi 8, thiab hloov 5 muaj nqi 16. Cov lej ntawm qhov tseem ceeb ntawm cov keyboards hauv ON txoj haujlwm muab qhov chaw nyob. Chaw nyob hauv thaj tsam 0…31 yog ua tau.

Compatibility Hom Probus IV
Yog tias kev sib raug zoo nrog rau yav dhau los Probus IV system yuav tsum tau, lub interface converter tuaj yeem raug teeb tsa rau hom kev sib raug zoo tshwj xeeb (hom 1). Txawm li cas los xij, hom no tsis pom zoo rau cov qauv tsim tshiab. Kev ua tau zoo tag nrho ntawm Probus V system tshiab tuaj yeem ua tiav hauv hom qauv.

LAN Ethernet (LANI 21/22)
Thaum programming ib daim ntawv thov tswj cov cuab yeej tshiab, nws raug nquahu kom siv TCP / IP rau kev sib txuas lus. TCP/IP tshem tawm qhov xav tau rau cov tsav tsheb ntxiv.

Ethernet

• 10/100 PIB-T
• RJ-45 connector

Fiber Optic Transmitter (Tx)

• LED qhov taw qhia link

Fiber Optic Txais (Rx)

• LED qhov taw qhia ua haujlwm

FAQ

• Kuv yuav kho qhov chaw nyob thawj (PA) ntawm lub cuab yeej li cas?
  Txhawm rau kho qhov chaw nyob thawj, nrhiav cov kev hloov pauv ntawm lub vaj huam sib luag tom qab ntawm lub cuab yeej IEEE-488 interface converter module. Teem cov keyboards raws li binary system, qhov twg txhua qhov hloov pauv muaj tus nqi tshwj xeeb. Cov lej ntawm qhov tseem ceeb ntawm cov keyboards hauv ON txoj haujlwm muab qhov chaw nyob. Tua lub hwj chim rau 5 vib nas this thiab tom qab ntawd tig nws dua los siv qhov kev hloov pauv.
• Dab tsi yog qhov chaw nyob thawj (PA) rau FuG cov khoom siv hluav taws xob?
  Qhov chaw nyob thawj zaug rau FuG cov khoom siv hluav taws xob yog PA = 8.
• Kuv tuaj yeem ua tiav kev sib raug zoo nrog lub qub Probus IV system li cas?
  Txhawm rau ua tiav kev sib raug zoo nrog rau yav dhau los Probus IV system, teeb tsa lub interface converter rau hom kev sib raug zoo (Hom 1). Txawm li cas los xij, nws tsis pom zoo rau kev tsim qauv tshiab vim tias kev ua haujlwm tag nrho ntawm Probus V system tsuas tuaj yeem ua tiav hauv hom qauv.

TshajVIEW

• ADDAT 30/31 module yog AD / DA interface rau kev tswj cov khoom siv hluav taws xob ntawm fiber ntau optics siv cov ntaub ntawv sib kis. Lub Rooj Tswjhwm Saib ADDAT txuas ncaj qha mus rau cov khoom siv hluav taws xob.
• Lub converter rau converting lub interface teeb liab mus rau ib tug fiber optics teeb liab mounted ntawm lub vaj huam sib luag rov qab. Txhawm rau kom ncav cuag lub suab nrov tshaj plaws tiv thaiv, lub teeb liab converter tuaj yeem ua haujlwm raws li cov khoom siv sab nraud sab nraud ntawm cov khoom siv hluav taws xob. Nyob rau hauv tas li ntawd, cov ntaub ntawv xa tawm sab nraud ntawm lub hwj chim mov kuj tshwm sim ntawm fiber optics.

Phau ntawv no yog tsim los ntawm: XP Power FuG, Am Eschengrund 11, D-83135 Schechen, Lub teb chaws Yelemees

IEEE 488

Pin assignment – ​​IEEE488

Cov ntaub ntawv teeb tsa interface

TSWV YIM: Rau kev teeb tsa ceev: Feem ntau, tsuas yog GPIB thawj qhov chaw nyob yuav tsum tau hloov kho ntawm cov keyboards 1…5. Lwm qhov hloov pauv 6…8 tseem nyob hauv OFF txoj haujlwm.

Interface Converter LED Qhov taw qhia

• LED ADDR
  Lub LED no yog nyob rau, thaum lub converter yog nyob rau hauv lub listener hais nyob rau hauv lub xeev los yog tham nyob rau hauv lub xeev.
• LED 1 SRQ
  Qhov LED no nyob rau, thaum lub converter lees paub SRQ kab. Tom qab qhov kev ntsuam xyuas serial, LED tawm mus.

GPIB Primary Address (PA)

• GPIB thawj qhov chaw nyob (PA) tso cai rau kev txheeb xyuas tag nrho cov chav nyob txuas nrog IEEE-488 lub tsheb npav.
• Yog li ntawd, ib qho PA tshwj xeeb yuav tsum tau muab rau txhua chav nyob ntawm lub npav.
• Cov tswj PC feem ntau muaj PA = 0 thiab cov chav sib txuas feem ntau muaj qhov chaw nyob ntawm 4 mus rau sab saud. Feem ntau, lub xeev xa khoom ntawm FuG cov khoom siv hluav taws xob yog PA = 8.
• Kev hloov kho ntawm PA yog ua tiav ntawm lub vaj huam sib luag tom qab ntawm lub cuab yeej ntawm IEEE-488 interface converter module. Tsis tas yuav qhib lub hwj chim.
• Tom qab hloov qhov hloov pauv, lub hwj huam mov yuav tsum tau hloov mus rau 5 vib nas this thiab hloov dua siab tshiab los siv qhov kev hloov pauv.

Compatibility Hom Probus IV

• Yog tias kev sib raug zoo rau yav dhau los Probus IV system yog qhov tsim nyog, lub interface converter tuaj yeem raug teeb tsa rau hom kev sib raug zoo tshwj xeeb (hom 1).
• Hom no tsis pom zoo rau cov qauv tshiab.
• Kev ua tau zoo tag nrho ntawm Probus V system tsuas yog ua tiav hauv hom qauv!

LAN Ethernet (LANI 21/22)

Nyob rau hauv rooj plaub ntawm programming ib daim ntawv thov tswj cov cuab yeej tshiab nws raug pom zoo kom siv TCP / IP rau kev sib txuas lus. Los ntawm kev siv TCP / IP, tsis xav tau kev tsav tsheb ntxiv.

Pin assignment – ​​LAN Ethernet (LANI 21/22)

Kev tswj ncaj qha ntawm TCP / IP

• Kev sib txuas teeb tsa thiab kev teeb tsa
  Nyob ntawm koj lub network, qee qhov kev teeb tsa yuav tsum tau ua. Ua ntej, kev sib txuas rau lub interface converter yuav tsum tau tsim. Rau qhov no, tus IP chaw nyob yuav tsum tau txiav txim siab. Txoj hauv kev pom zoo los txheeb xyuas cov cuab yeej hauv Network thiab txheeb xyuas nws qhov chaw nyob IP yog siv qhov program "Lantronix Device Installer"
  CEEB TOOM Ceev faj thaum txuas mus rau lub tuam txhab network, vim hais tias tsis ncaj ncees lawm los yog duplicate IP chaw tuaj yeem ua rau muaj teeb meem ntau thiab tiv thaiv lwm lub PC los ntawm kev siv network!
  Yog tias koj tsis paub txog kev tswj hwm network thiab kev teeb tsa, peb xav kom ua koj thawj kauj ruam hauv ib lub network uas tsis muaj kev sib txuas nrog koj lub koom haum network (kev sib txuas ntawm CrossOver-cable)! Xwb, thov nug koj tus thawj tswj hwm hauv zos kom pab!
• Nruab DeviceInstaller
  Nyob ntawm koj lub network, qee qhov kev teeb tsa yuav tsum tau ua.
  1. Download tau qhov "Lantronix Device Installer" program los ntawm www.lantronix.com thiab khiav nws.
  2. Tom qab xaiv hom lus koj nyiam.
  3. Tam sim no nws tau kuaj xyuas seb "Microsoft .NET Framework 4.0" lossis "DeviceInstaller" twb tau teeb tsa hauv koj lub PC. Yog tias "Microsoft .NET Framework" tseem tsis tau teeb tsa, nws yuav raug ntsia ua ntej.
  4. Txais cov lus tso cai ntawm "Microsoft .NET Framework 4.0".
  5. Lub installation ntawm "Microsoft .NET Framework 4.0" tuaj yeem siv sijhawm txog 30 feeb.
  6. Tam sim no lub installation yuav tsum ua kom tiav ntawm "Finish".
  7. Tom qab ntawd lub installation ntawm "DeviceInstaller" pib.
  8. lees paub cov nplooj ntawv sib txawv nrog "Tom ntej>".
  9. Xaiv koj lub nplaub tshev rau lub installation.
  10. Paub meej tias qhov kev zov me nyuam yuav tsum tau nruab.
      Tam sim no qhov kev pab cuam "DeviceInstaller" yog ntsia.
• Kev kuaj pom ntawm lub cuab yeej
  Nco tseg Cov lus qhia hauv qab no hais txog kev siv Microsoft Windows 10.
  1. Tom qab kev teeb tsa, pib "DeviceInstaller" los ntawm Windows pib ntawv qhia zaub mov.
  2. Yog tias Windows Firewall ceeb toom tshwm, nyem rau ntawm "Cia kev nkag mus".
  3. Txhua yam khoom siv pom hauv lub network yuav tshwm sim. Yog tias cov cuab yeej xav tau tsis tshwm sim, koj tuaj yeem rov pib tshawb nrhiav nrog lub pob "Tshawb".
  4. Qhov chaw nyob IP, nyob rau hauv rooj plaub no 192.168.2.2, yog xav tau rau kev sib txuas rau lub cuab yeej. Raws li kev teeb tsa hauv lub network, IP Chaw nyob yuav hloov pauv txhua zaus lub cuab yeej siv hluav taws xob. Tom qab koj tau txais IP-Address ntawm DeviceInstaller koj tuaj yeem txuas nrog lub cuab yeej.
• Configuration ntawm lub web interface
  1. Nws raug nquahu kom siv a webbrowser rau configuration.
     Ntaus tus IP chaw nyob ntawm koj lub cuab yeej rau hauv qhov chaw nyob bar thiab ntaus nkag.
  2. Lub qhov rais nkag mus yuav pom, tab sis koj tsuas yog yuav tsum nyem "OK". Los ntawm lub neej ntawd, tsis tas yuav tsum muaj daim ntawv pov thawj nkag.
• Customize Chaw
  Ib tus neeg siv khoom tshwj xeeb IP chaw nyob thiab lub npog ntsej muag subnet tuaj yeem teeb tsa hauv thaj chaw "Siv tus IP teeb tsa hauv qab no". Cov qhia IP chaw nyob / subnet npog yog examples. "Tau txais IP chaw nyob cia li" yog lub Hoobkas pib.
• Chaw nres nkoj hauv zos
  Qhov chaw nres nkoj hauv zos "2101" yog lub Hoobkas ua ntej.
• Cov ntaub ntawv ntxiv
  Lub interface converter yog raws li nyob rau hauv lub embedded ntaus ntawv Lantronix-X-Power. Cov neeg tsav tsheb hloov tshiab rau cov haujlwm tshiab thiab cov ntaub ntawv ntxiv tuaj yeem tau txais los ntawm: http://www.lantronix.com/device-networking/embedded-device-servers/xport.html

Profibus DP tau

Pin assignment ntawm lub interface

Kev teeb tsa interface - GSD File
GSD file ntawm lub interface converter nyob rau hauv cov directory "Digital_Interface\ProfibusDP\GSD". Nyob ntawm qhov version ntawm lub converter module, yog "PBI10V20.GSD" yuav tsum tau siv. Yog tias file yog tsis raug, lub hwj huam mov unit tsis tau lees paub los ntawm tus tswv.

Kev teeb tsa Interface - Kev teeb tsa ntawm Node Chaw Nyob
Qhov chaw nyob ntawm node txheeb xyuas cov units (=nodes) txuas nrog Profibus. Ib qhov chaw nyob tshwj xeeb yuav tsum raug muab rau txhua qhov ntawm lub npav. Qhov chaw nyob yog teem nrog keyboards nyob rau sab nraum qab ntawm lub interface converter. Lub vaj tsev ntawm lub hwj huam mov tsis tas yuav qhib. Tom qab ib qho kev hloov pauv hauv kev teeb tsa, lub zog hluav taws xob (interface converter) yuav tsum tau hloov mus rau yam tsawg 5 vib nas this. Tus qhev chaw nyob hauv thaj tsam 1…126 yog ua tau.

Qhov taw qhia

• Ntsuab LED -> SERIAL OK
• Qhov LED no nyob rau, yog tias qhov sib txuas ntawm fiber ntau optic ntawm ADDAT puag module thiab interface converter ua haujlwm raug.
• Nyob rau tib lub sijhawm, LED BUSY ntawm lub vaj huam sib luag pem hauv ntej ntawm lub zog hluav taws xob txuas ntxiv mus, qhia txog kev hloov pauv cov ntaub ntawv txuas ntxiv ntawm lub interface converter thiab ADDAT puag module.
• Liab LED -> BUS yuam kev
• Qhov LED no nyob rau, yog tias tsis muaj kev sib txuas rau ProfibusDP Master.

Hom kev ua haujlwm

• Lub ProfibusDP interface converter muab 16 Byte input cov ntaub ntawv thaiv thiab 16 Byte tso tawm cov ntaub ntawv thaiv.
• Cov ntaub ntawv nkag los ntawm Profibus yog khaws cia hauv cov ntaub ntawv nkag nkag.
• Qhov thaiv no tau hloov pauv mus raws li 32-tus cim hexadecimal hlua rau ADDAT puag module. (Rau npe “>H0” ntawm ADDAT 30/31)
• ADDAT puag module teb nrog 32-tus cim hexadecimal hlua.
• Cov hlua no muaj 16 Bytes ntawm kev saib xyuas thiab cov cim xwm txheej.
• Lub Profibus interface converter khaws cov 16 Bytes hauv cov ntaub ntawv tso tawm, uas tuaj yeem nyeem tau los ntawm Profibus tus tswv.
• Lub sijhawm voj voog yog kwv yees li 35ms.
• Thov xa mus rau cov lus piav qhia ntawm Kev Sau Npe "> H0" hauv daim ntawv Digital Interfaces Command Reference ProbusV.

Hnub Formats

Xav paub ntxiv
Lub interface converter Profibus DP yog raws li tus qauv converter "UNIGATE-IC" los ntawm Deutschmann Automationstechnik (cov nplooj ntawv khoom). Txhua yam Profibus baud tus nqi nce txog 12 MBit / s tau txais kev txhawb nqa. Cov chaw hloov dua siab tshiab yog sau ntawv-tswj nrog lub sij hawm voj voog ntawm approx. 35ms ib.

RS 232/422

Cov ntaub ntawv teeb tsa interface
Txhua lub cuab yeej uas tau nruab nrog RS232, lossis RS422 sab hauv lossis sab nraud hloov pauv, tuaj yeem tswj tau los ntawm lub PC hla lub COM chaw nres nkoj. Los ntawm view ntawm daim ntawv thov programmer, tsis muaj qhov sib txawv ntawm cov kev hloov pauv no.

RS232, sab nraud interface converter

• Cov khoom siv hluav taws xob txuas nrog lub pc ntawm Plastic Optic Fiber txuas (POF). Qhov no ua kom muaj kev tiv thaiv suab nrov tshaj plaws.
• Qhov siab tshaj plaws txuas qhov deb yog 20m.
• Nyob rau sab PC, lub interface converter txuas ncaj qha mus rau tus qauv COM chaw nres nkoj. Lub teeb liab interface Tx yog siv los ua lub zog rau lub converter, yog li tsis tas yuav khoom siv sab nraud.

Fiber optic kev twb kev txuas:

• Cov ntaub ntawv tawm ntawm lub converter ("T", Transmit) yuav tsum tau txuas nrog cov ntaub ntawv tawm tswv yim ("Rx", Txais) ntawm lub hwj huam mov.
• Cov ntaub ntawv tawm tswv yim ntawm lub converter ("R", Txais) yuav tsum tau txuas nrog cov ntaub ntawv tso zis ("T", Transmit) ntawm lub hwj huam mov.

Pin assignment – ​​RS232, intern

Txhawm rau tsim kev sib txuas rau tus qauv PC nws txaus los txuas tus pins 2, 3 thiab 5 nrog tib tus PINs ntawm PC com chaw nres nkoj.
Txheem RS-232 cables nrog 1: 1 tus pin txuas tau pom zoo.

CEEB TOOM Muaj NULL-modem cables uas twb muaj lawm nrog Pins 2 thiab 3 hla. Xws li cov cables tsis ua haujlwm.

Pin assignment – ​​RS422

CEEB TOOM Txoj haujlwm tus pin ua raws li tus qauv quasi. Yog li ntawd, nws tsis tuaj yeem lav, tias txoj haujlwm tus pin yog sib xws rau koj lub PC RS-422 cov zis. Nyob rau hauv cov ntaub ntawv ntawm tsis ntseeg, tus pin assignment ntawm lub PC thiab interface converter yuav tsum tau xyuas kom meej.

TSI RS485

RS485 Cov ntaub ntawv keeb kwm yav dhau

• "RS485 Bus" feem ntau cuam tshuam nrog 2-xaim tsheb npav yooj yim uas siv los txuas ntau tus tub txib nyob nrog tus tswv cuab (piv txwv li PC).
• Nws tsuas yog txhais cov theem teeb liab ntawm lub cev ntawm kev sib txuas lus.
• RS485 tsis txhais cov ntaub ntawv tawm tswv yim, lossis ib qho kev cai lossis txawm tias tus pin txuas txuas!
• Yog li ntawd, txhua qhov chaw tsim khoom ntawm RS485 cov cuab yeej yog dawb kiag li hauv kev txhais cov chav nyob ntawm lub tsheb npav RS485 sib txuas lus li cas.
• Qhov no ua rau cov chav ua haujlwm tsis zoo los ntawm cov tuam txhab ua lag luam feem ntau tsis ua haujlwm ua ke kom raug. Txhawm rau ua kom cov chav ua tau zoo los ntawm cov tuam txhab ua lag luam ua haujlwm ua ke, cov qauv nyuaj xws li ProfibusDP tau qhia. Cov qauv no yog nyob ntawm
• RS485 ntawm cov txheej txheem lub cev, tab sis kuj txhais cov kev sib txuas lus ntawm qib siab dua.

Interface Converter RS232/USB rau RS485

• Ib lub PC uas muaj RS232 / USB interface tuaj yeem hloov kho rau RS485 los ntawm kev hloov pauv hloov pauv muaj nyob hauv khw.
• Feem ntau, cov converters no ua haujlwm zoo hauv hom duplex (2 khub ntawm cov xov hlau).
• Nyob rau hauv ib nrab duplex hom (1 khub ntawm cov xov hlau), lub transmitter ntawm txhua qhov chaw nres tsheb yuav tsum tau disabled tam sim ntawd tom qab lub kawg byte raug xa mus kom tshem tawm lub tsheb npav rau cov ntaub ntawv tom ntej xav tau.
• Hauv feem ntau muaj RS232 - RS485 interface converters lub transmitter yog tswj los ntawm RTS teeb liab. Qhov kev siv tshwj xeeb ntawm RTS no tsis tau txais kev txhawb nqa los ntawm cov txheej txheem software tsav tsheb thiab xav tau software tshwj xeeb.

Pin assignment – ​​RS485

RS485 tsis txhais cov haujlwm pin. Txoj haujlwm ntawm cov pins sib haum rau cov kab ke ib txwm muaj. Feem ntau yuav, txoj haujlwm tus pin ntawm PC sab lossis lwm yam khoom siv yuav ua tsis tau!

Configuration – Chaw nyob

• Chaw nyob 0 yog lub Hoobkas ua ntej.
• Yog tias ntau tshaj ib lub cuab yeej txuas ua ke ntawm RS485, qhov chaw nyob nyiam tuaj yeem raug teeb tsa raws li lub Hoobkas. Yog li ntawd, thov hu rau XP Power.
• Hauv qhov xwm txheej siv ib txwm, hloov chaw nyob ntawm cov khoom siv yog li tsis tsim nyog.
• Lub calibration hom yuav tsum tau enabled thiaj li yuav hloov qhov chaw nyob ntawm ib tug ntaus ntawv.
• Ua kom lub calibration hom yog ua tiav ntawm koj tus kheej txaus ntshai! Yuav kom ua tau li ntawd, lub cuab yeej yuav tsum tau qhib uas yuav tsum tau ua los ntawm cov neeg ua haujlwm cob qhia nkaus xwb! Cov cai tswj kev nyab xeeb tam sim no yuav tsum txaus siab!

Network Structure thiab Termination

• Lub tsheb npav yuav tsum muaj cov qauv linear nrog 120 Ohm termination resistors ntawm ob qhov kawg. Hauv ib nrab duplex hom, 120 Ohm resistor ntawm Pins 7 thiab 8 tuaj yeem siv rau lub hom phiaj no.
• Lub hnub qub topology lossis cov ceg ntoo ntev yuav tsum zam kom tsis txhob muaj teeb meem degradation vim kev xav.
• Tus tswv cuab yeej tuaj yeem nyob txhua qhov chaw hauv lub npav.

Fullduplex hom (sib cais Rx thiab Tx)

• Lub tsheb npav muaj 2 lub xov hlau (4 lub teeb liab xov hlau thiab GND)
• Sijhawm: Lub sijhawm teb ntawm ADDAT module yog qis dua 1ms (feem ntau yog ob peb 100us). Tus tswv yuav tsum tos tsawg kawg 2ms tom qab tau txais qhov kawg byte ntawm cov lus teb ua ntej pib xa cov hlua txuas ntxiv. Txwv tsis pub, cov ntaub ntawv sib tsoo ntawm lub npav yuav tshwm sim.

Ib nrab duplex Kev Ua Haujlwm (Rx thiab Tx ua ke ntawm ib qho Hlau Pair)

• Lub tsheb npav muaj 1 khub hlau (2 lub teeb liab xov hlau thiab GND)
• Lub sijhawm 1: Lub sijhawm teb ntawm ADDAT module yog qis dua 1ms (feem ntau yog ob peb 100us). Tus tswv yuav tsum muaj peev xwm hloov od nws transmitter nyob rau hauv 100us tom qab lub xeem byte kis.
• Lub sijhawm 2: Tus qhev lub transmitter (Probus V RS-485 interface) tseem ua haujlwm rau qhov siab tshaj plaws ntawm 2ms tom qab lub kawg byte kis tau thiab tau teem rau siab impedance tom qab no. Tus tswv yuav tsum tos tsawg kawg 2ms tom qab tau txais qhov kawg byte ntawm cov lus teb ua ntej pib xa cov hlua txuas ntxiv.
• Ua txhaum lub sij hawm txwv no ua rau cov ntaub ntawv sib tsoo.

USB

Pin assignment – ​​USB

Kev teeb tsa
USB interface ua haujlwm ua ke nrog tus tsav tsheb software ua lub chaw nres nkoj virtual COM. Yog li ntawd, nws yooj yim rau kev pab cuam lub hwj chim tsis muaj kev paub tshwj xeeb USB. Koj tuaj yeem siv cov software uas twb muaj lawm uas ua haujlwm txog tam sim no nrog lub chaw nres nkoj COM tiag.
Thov siv tus tsav tsheb installation file los ntawm XP Power Terminal pob.

Automatic Driver Installation

1. Txuas lub hwj huam mov rau PC ntawm USB cable.
2. Yog tias muaj kev sib txuas hauv internet, Windows 10 yuav ntsiag to txuas rau Windows Update website thiab nruab ib tus neeg tsav tsheb tsim nyog nws pom rau lub cuab yeej.
   Kev teeb tsa tiav lawm.

Installation ntawm executable teeb file

1. Lub executable CDM21228_Setup.exe nyob hauv XP Power Terminal download pob ntawv.
2. Right-click lub executable thiab xaiv "Alle extrahieren ..."
3. Khiav lub executable raws li tus thawj tswj hwm thiab ua raws li cov lus qhia.
4. 
5. 
6. 

Thaum lub installation tiav lawm, nyem "finish".

Cov ntawv ntxiv

Kev teeb tsa

• Baud Rate
  Lub neej ntawd Baud tus nqi rau cov khoom siv nrog a:
  • USB interface yog teem rau 115200 Baud.
    Qhov siab tshaj plaws baud tus nqi rau USB yog 115200 Baud.
  • LANI21/22 interface yog teem rau 230400 Baud.
    Qhov siab tshaj plaws baud tus nqi rau LANI21/22 yog 230k Baud.
  • RS485 interface yog teem rau 9600 Baud.
    Qhov siab tshaj plaws baud tus nqi rau RS485 yog 115k Baud.
  • RS232 / RS422 interface yog teem rau 9600 Baud.
    Qhov siab tshaj plaws baud tus nqi rau RS485 yog 115k Baud.

Terminator
Lub cim txiav "LF" yog lub Hoobkas ua ntej.

Kev ua haujlwm

1. Ua ntej pib lub commissioning ntawm lub interface, lub DC fais fab mov yuav tsum tau muab tua.
2. Lub interface ntawm lub computer tswj yuav tsum tau txuas nrog lub interface ntawm DC fais fab mov raws li tau teev tseg.
3. Tam sim no tig rau POWER hloov.
4. Nias lub REMOTE hloov (1) ntawm lub vaj huam sib luag pem hauv ntej kom lub LOCAL LED (2) tua. Yog hais tias muaj ib qho analog interface ntxiv, teeb qhov hloov (6) rau DIGITAL. DIGITAL LED (5) teeb.
5. Pib koj qhov kev khiav hauj lwm software thiab tsim kom muaj kev sib txuas rau lub interface hauv lub cuab yeej. Cov cuab yeej tam sim no tswj hwm los ntawm kev khiav haujlwm software. Lub BUSY LED (4) teeb sai sai thaum cov ntaub ntawv khiav mus rau kev saib xyuas lub hom phiaj. Cov ntaub ntawv ntxiv txog cov lus txib thiab kev ua haujlwm tuaj yeem pom hauv daim ntawv Digital Interface Command Reference Probus V

Kom nyab xeeb hloov o: lub hwj huam mov, ua raws li hauv qab no:
Cov txheej txheem ntawd yog qhov tseem ceeb heev rau kev nyab xeeb. Qhov no yog vim qhov tso zis tawm voltage tseem tuaj yeem pom hauv voltage zaub. Yog hais tias chav tsev hloov pauv o: tam sim ntawd siv lub AC Fais fab hloov, tej yam txaus ntshai voltage tam sim no (xws li them capacitors) tsis tuaj yeem pom txij li cov zaub tau tig o:.

1. Nrog rau kev khiav hauj lwm software, lub setpoints thiab tam sim no yog teem rau "0" thiab ces cov zis yog switched tawm.
2. Tom qab qhov tso zis tsawg dua <50V, hloov lub tsev tag nrho tawm siv lub POWER (1) hloov. Ua tib zoo mloog rau lub zog seem hauv koj daim ntawv thov!
   Lub DC fais fab mov raug kaw.

Kev phom sij ntawm kev siv cov programming tsis raug

• Kev phom sij ntawm hluav taws xob poob ntawm lub hwj chim tawm!
  • Yog tias cov digital interface cable raug rub thaum lub cuab yeej ua haujlwm hauv DIGITAL hom, cov khoom siv tawm yuav tuav tus nqi kawg!
  • Thaum hloov los ntawm hom DIGITAL mus rau LOCAL lossis ANALOG hom, cov txiaj ntsig ntawm cov cuab yeej yuav tswj hwm tus nqi kawg uas tau teeb tsa los ntawm digital interface.
  • Yog tias cov khoom siv DC tig od los ntawm POWER hloov lossis los ntawm outage voltage muab, cov nqi teeb tsa yuav raug teeb tsa rau "0" thaum lub cuab yeej rov pib dua.

Kev ntsuas kev sib txuas: NI IEEE-488

Yog tias koj siv National Instruments IEEE-488 ntsaws rau hauv daim npav hauv koj lub PC, qhov kev sib txuas tuaj yeem kuaj tau yooj yim heev. Daim npav xa tuaj ua ke nrog ib qho kev pab cuam: "National Instruments Measurement And Automation Explorer". Short form: “NI MAX”. Nws yog siv rau cov nram qab no example.

Nco tseg Lwm cov tuam txhab lag luam ntawm IEEE-488 boards yuav tsum muaj cov haujlwm zoo sib xws. Thov xa mus rau lub chaw tsim khoom ntawm koj daim npav.

Example for NI MAX, Version 20.0

1. Txuas FuG fais fab mov rau PC ntawm IEEE-488.
2. Pib NI MAX thiab nyem rau ntawm "Geräte und Schnittstellen" thiab "GPIB0".
3. Tam sim no nyem rau ntawm "Scan for Instruments". Lub hwj huam mov yuav teb nrog "FuG", Hom thiab naj npawb.
4. Nyem rau ntawm "Kommunikation mit Gerät": Tam sim no koj tuaj yeem ntaus cov lus txib rau hauv "Xa" teb: Tom qab pib tus neeg sib txuas lus, txoj hlua "*IDN?" twb muab tso rau hauv qhov chaw nkag. Qhov no yog cov lus nug tus qauv rau kev txheeb xyuas txoj hlua ntawm lub cuab yeej.
   Yog tias koj nyem rau ntawm "QUERY" qhov "Xa" teb yog xa mus rau lub hwj chim mov thiab cov lus teb txoj hlua yuav tshwm nyob rau hauv "String Received" teb.
   Yog tias koj nyem rau ntawm "WRITE", qhov "Xa" teb raug xa mus rau lub zog hluav taws xob, tab sis cov lus teb tsis tau sau los ntawm cov khoom siv hluav taws xob.
   Nyem rau ntawm "READ" sau thiab qhia cov lus teb.
   (“ QUERY” tsuas yog ua ke ntawm “SAU” thiab “NYEEM”.)
5. Nyem rau "QUERY":
   Lub hwj chim mov outputs hom thiab serial tooj.

Kuaj kev sib txuas: XP Power Terminal
Qhov kev pab cuam XP Fais Fab Terminal tuaj yeem siv los ntsuas qhov kev sib txuas mus rau chav tsev fais fab. Qhov no tuaj yeem rub tawm los ntawm Resources tab ntawm txhua nplooj ntawv XP Power Fug khoom.

Kev sib txuas lus yooj yim examples

IEEE 488
Txhawm rau txuas lub cuab yeej, yuav luag txhua qhov kev pabcuam davhlau ya nyob twg tuaj yeem siv.

ProfibusDP

• Voltage teev nqi
  Input data block Bytes 0 (=LSB) thiab Byte 1 (=MSB)
  0…65535 ua rau 0…nominal voltage.
  Hauv cov khoom siv hluav taws xob bipolar, tus nqi teeb tsa tuaj yeem hloov pauv los ntawm kev teeb tsa ntawm Byte4 / Bit0.
• Cov nqi tam sim no
  Input data block Bytes 2 (=LSB) thiab Byte 3 (=MSB)
  0…65535 ua rau 0… nominal tam sim no.
  Hauv cov khoom siv hluav taws xob bipolar, tus nqi teeb tsa tuaj yeem hloov pauv los ntawm kev teeb tsa ntawm Byte4 / Bit1.
• Tso zis voltage
  DANGER Los ntawm kev xa cov ntaub ntawv hloov pauv (sau npe "> BON") cov zis tau qhib tam sim!
  Input cov ntaub ntawv thaiv Byte 7, ntsis 0
  Cov zis ntawm lub hwj huam mov yog hluav taws xob tso tawm thiab hloov od.
• Nyeem rov qab ntawm cov zis voltage
  Muab cov ntaub ntawv thaiv Bytes 0 (=LSB) thiab Byte 1 (=MSB)
  0…65535 ua rau 0…nominal voltage.
  Qhov kos npe ntawm tus nqi yog nyob rau hauv Byte4 / Bit0 (1 = tsis zoo)
• Nyeem rov qab ntawm cov zis tam sim no
  Muab cov ntaub ntawv thaiv Bytes 2 (=LSB) thiab Byte 3 (=MSB)
  0…65535 ua rau 0… nominal tam sim no.
  Qhov kos npe ntawm tus nqi yog nyob rau hauv Byte4 / Bit1 (1 = tsis zoo)

Cov txheej txheem qhia thiab programming

Rau kev ua tiavview ntawm cov ntawv sau npe nrog cov lus txib ntxiv thiab kev ua haujlwm xa mus rau cov ntaub ntawv Digital Interfaces Command Reference Probus V. Lub zog muab hluav taws xob yog tswj los ntawm cov lus txib ASCII yooj yim. Ua ntej xa cov lus txib tshiab, cov lus teb sib xws rau cov lus txib dhau los yuav tsum tau tos thiab ntsuas yog tias xav tau.

• Txhua txoj hlua hais kom ua yuav tsum raug txiav los ntawm yam tsawg kawg ib qho ntawm cov cim txiav tawm hauv qab no lossis ib qho kev sib xyaw ua ke ntawm lawv: "CR", "LF" lossis "0x00".
• Txhua txoj hlua hais kom xa mus rau chav tsev muab hluav taws xob yuav raug teb los ntawm cov kab lus teb sib xws.
• "npliag" cov hlua hais kom ua, piv txwv li cov hlua uas muaj cov cim tsuas yog txiav tawm, raug tso tseg thiab tsis rov qab cov lus teb.
• Tag nrho cov ntaub ntawv nyeem thiab tuav tes los ntawm cov khoom siv hluav taws xob raug txiav nrog lub teeb tsa (saib npe "> KT" lossis "> CKT" thiab "Y" hais kom ua)
• Tau txais lub sijhawm: Yog tias tsis muaj cov cim tshiab tau txais ntev dua 5000ms tag nrho cov cim tau txais yav dhau los yuav raug muab pov tseg. Vim lub sijhawm ntev heev, nws tuaj yeem xa cov lus txib manually siv lub davhlau ya nyob twg program.
• Hais kom ntev: Qhov siab tshaj plaws hais kom ua hlua ntev yog txwv rau 50 cim.
• Txais tsis tau: ADDAT muaj 255 tus cim ntev FIFO Txais Tsis Muaj.

Cov ntaub ntawv / Cov ntaub ntawv

XP Power Digital Programming [ua pdf] Phau ntawv qhia Programming, Digital Programming

Cov ntaub ntawv

• Cov neeg siv phau ntawv