Pulse Series Controller Pulse Red

I-PULSE
I-Commercial Direct Drive Door Operator ye-Balanced Sectional kunye ne-Rolling Steel Doors. Incwadana yokuFakelo kunye nokuSeta/iMiyalelo yoMsebenzisi
I-Patent yase-US enguNombolo 11105138
Ngolwazi oluthe vetshe, nceda uqhagamshelane www.devancocanada.com okanye ufowunele umnxeba simahla ngo-1-855-931-3334

NGOKUBANZIVIEW

Enkosi ngokuthenga lo mqhubi wePulse Direct Drive Door. Lo mqhubi uthembekileyo uyilelwe umsebenzi oqhubekayo womjikelo kuDongo lwakho lwezoRhwebo kwaye unokwandisa ubomi bomnyango wakho wecandelo olungelelanisiweyo kunye nekhono lawo lokuqalisa elithambileyo/elithambileyo lokumisa.
Ikwanezantya zokuvula ezihlengahlengiswayo ukuya kuthi ga malunga ne-24” ngesekhondi, i-backup yebhetri enokusebenzisa ucango kwimeko yokusilela kwamandla, ukhuseleko lwangoku, kunye nokujongwa kwamandla okubuyisela umva ngokuzenzekelayo, kunye neminye imisebenzi emininzi enokucwangciswa.
I-PULSE 500-1000 SERIES UL325:2023 zidweliswe – INQAKU LOKUTHOBELA
Aba baSebenzi babonelelwa ngePolarized Reflective Photo-Eye, eqhagamshelwe kwiSitena soku-1 segalelo 'lweZixhobo eziBuyisayo' kwiPaneli yoLawulo (Thru-Beam Photo-Eye kwi-1HP & -WP Models ukuya kwiSitena sesi-2). Nje ukuba iqhosha lokuVala lisebenze, umqhubi uyaqinisekisa ukuba i-Photo-Eye ixhunyiwe kwaye iyasebenza, kwaye iyaqhubeka nokubeka iliso kwinzwa njengoko umnyango uvala.
Itheminali ezinikeleyo (iTerminal 2 Reversing Devices) ibonelelwe ukuba isebenze kunye neZixhobo zokuBuyisa uQhobo.
Igalelo (I-Terminal 3 Reversing Devices) kwizixhobo ezingajongwanga ukubuyisela umva (okt edge edge yepneumatic).
I-Pulse Operator iya kuqalisa i-Pulse Operator ukuze iqalise i-Pulse/Bamba UKUVALA iprothokholi ukuba ayifumani isixhobo esibuyisela umva esebenzayo nokuba kukwiSitena soku-1 okanye sesi-2. Akukho nanye kwezi terminal inokugqithwa okanye 'itsibe'. Qaphela ukuba ngexesha lokutyhala/Bamba ukuVala iiprothokholi, ucango luza kubuya umva ukuba alufikeleli ngokupheleleyo kumda ovaliweyo nge-UL 325 nganye.

IBHOKISI YOMTHETHO

Ngaphambi kokuba uqalise ukufakela, nceda uqinisekise ukuba onke amacandelo abalwa:

1. IMoto, i-Gearbox, i-Encoder, iNdibano yeBhokisi yeJunction
2. Iphaneli yokulawula
3. Izibiyeli zoMda kunye ne-Hardware (Iibakaki ze-engile zoMda wokuNqanda ukunyuswa kwiingoma zocango)
4. Ingalo yeTorque, iiBholithi zokuFaka, isibiyeli esiNyisayo
5. Ikhola ye-Shaft kunye ne-Shaft Key
6. Isixhobo esibuyisela umva-Ifoto-iliso eliBonakalayo (i-Thru-Beam Photo-Eye ibandakanyiwe kwi-1HP & -WP Models)
7. Iibhetri ze-12V ezimbini, iLead-Acid eTshajwa kwakhona

Kwimeko apho nayiphi na kwezi zinto zingasentla zilahlekile, nceda uqhagamshelane ne-iControls kwaye usinike iinkcukacha zecandelo elilahlekileyo (iindawo), kunye nenombolo yesiriyali yomsebenzi wakho.

UBUGCISA OPERATOR PHEZULUVIEW

Imoto

UMSEBENZI WAMANDLA	I-Pulse 500 = 1/2 HP	I-Pulse 750 = 3/4 HP		I-Pulse 1000 = 1 HP
I-SPEED:	1750 RPM
NGOKU (FLA):	1/2 HP = 5A	3/4 HP = 7.6A		1 HP = 10A
ITOQUE YOKUPHUMA:	Ukubetha 500-1:	30:1=55.3Nm	40:1=73.7Nm	50:1=92.2Nm	60:1=110.5Nm
	Ukubetha 750-1:	30:1=55.2Nm	40:1=73.6Nm	50:1=92.2Nm	60:1=110.5Nm
	Ukubetha 750-1.25:	30:1=55.3Nm	40:1=73.7Nm	50:1=92.1Nm	60:1=110.5Nm
	Ukubetha 1000-1:	30:1=73.6Nm	40:1=98.2Nm	50:1=92.1Nm	60:1=147.3Nm
	Ukubetha 1000-1.25:	30:1=73.7Nm	40:1=98.2Nm	50:1=122.8Nm	60:1=147.4Nm

Umbane

UKUNIKEZELWA KOMQOLOTAGE:	I-110-130 okanye i-208-240V Vac, i-1ph Input (Onke amandla angenayo adityaniswe kwibhokisi yokudibanisa enikeziweyo)
IINKCUKACHA:	½ HP= 2 x 5Ah, ¾ HP= 2 x 7Ah, 1 HP= 2 x 9Ah
ULAWULO UMQULUTAGE:	I-24Vdc, i-1A Amandla/uQhagamshelwano olunikezelweyo ukuze lusebenze kunye nokubuyisela umva izixhobo
I-AUX RELAY:	I-1 SPDT Programmable Relay (ifektri engagqibekanga ukuze isebenze kwiMida eVulekileyo)

Ukhuseleko 

I-PHOTO-EYE okanye i-THRU-BEAM SENSOR:	I-Polarized Photo-eye Sensor/Reflector ene-Bracket okanye i-Thru-Beam sensor ebonelelwe ngeyunithi njenge-non-impembelelo yokubuyisela umva ukhuseleko lwesixhobo.
AMANDLA OUTAGUMSEBENZI WE-E:	Ugcino lwebhetri ukuvula/ukuvala ucango xa kukho amandla-outage. I-3/8” ye-ratchet socket ye-crank ye-manual evulekileyo / evaliweyo njenge-redundancy eyongeziweyo.

Nceda Jonga ku Wethu Webindawo yoBuninzi eCetyisiweyo kwi-Counter Ibhalansi yeCandelo lobungakanani bocango kunye nobunzima boMsebenzi ngamnye (www.iControls.ca).

KUBALULEKILEYO
ISILUMKISO – Le miyalelo ijoliswe kubasebenzi abanamava abaqeqeshelwe inkonzo kunye nokufakelwa kweengcango zecandelo kunye nabaqhubi. Onke amanyathelo okhuseleko kunye neekhowudi zendawo kufuneka zilandelwe.

1. FUNDA UZE ULANDE YONKE IMIYALELO YOKUFAKA.
2. Yiba nabasebenzi benkonzo abaqeqeshiweyo benze ulungiso oluyimfuneko ukuqinisekisa ukuba umnyango usebenza kakuhle ngaphandle kwengxolo engaqhelekanga. Faka i-opharetha kuphela kucango olusebenza kakuhle nolulungelelanisiweyo.
3. Susa zonke iintambo zokutsala kwaye ususe izitshixo (ngaphandle kokuba ngoomatshini kunye/okanye uqhagamshelwe ngombane kwiyunithi yombane) eqhagamshelwe emnyango phambi kokufaka umqhubi.
4. Umsebenzisi wocango lwezorhwebo/loshishino othe waveza iindawo ezihambayo ezinokwenzakalisa abantu okanye oqeshe isithuthi esithathwa njengesingafikelelekiyo ngokungangqalanga ngokwesolotya le-10.6 ngenxa yendawo ekuyo ngaphezulu komgangatho uya kubandakanya:
   a. Faka umsebenzisi emnyango ubuncinane 2.44m (8 ft) okanye ngaphezulu phezu komgangatho: okanye
   b. Ukuba umqhubi kufuneka afakwe ngaphantsi kwe-2.44m (8ft) ngaphezu komgangatho, ngoko iindawo ezihambayo eziveziweyo kufuneka zikhuselwe ngezigqubuthelo okanye ukugada; okanye
   c. Zombini a. kunye b.
5. Musa ukuqhagamshela umsebenzisi kumbane wonikezelo de uyalelwe ukuba enze njalo.
6. Fumana isikhululo solawulo: (a) phambi komnyango, kunye (b) kubude obuncinane be-1.53m (5 ft) ngaphezu kwemigangatho, indawo yokuhlala, izitepsi, okanye nawuphina omnye umphezulu osecaleni ohambayo kunye (c) kude nayo yonke into ehambayo. iinxalenye.
7. Faka i-Entrapment Warning Placard ecaleni kwesikhululo solawulo kwindawo ebonakalayo.

IIMFUNO ZENDIBANO ZOKUFAKEKELA NGAPHAMBILI

PHAMBI KOFAKA, QINISEKISA UKUBA UCANGO LAKHO LULINGANISILE NGOKUFANELEKILEYO KWAYE LUBALEKA KAHLE. KWAKHONA QINISEKISA UKUBA IBRACKETHI ZOMDA (EZIBONISWAYO) ZIFAKIWE KWAYE ZIKHUSELEKILE NGOKUFANELEKILEYO. I-BUMPER/PUSHER SPRINGS INOKUSETYENZISWA ENDAWENI YE-, OKANYE OKONGEZELELWEYO KWIIBRACKETHI ZOMDA ZE-PULUSE OPERATORS, KODWA KUFANELE KUFAKWE PHAMBI KOKUSEBENZA.
IiMsebenzi zokunyuswa kweeMfuno
Abaqhubi be-Pulse bafakwe ngokuthe ngqo kwi-shaft yomnyango. Ngaphambi kokufaka umqhubi, nceda uqinisekise ukuba kulandelwa imigaqo elandelayo:
Ucango lulungelelaniswe kakuhle, luvavanyelwa ukusebenza kakuhle ngaphandle kwengxolo engaqhelekanga.
Izibiyeli ezibonelelweyo zoMda kufuneka zifakwe ubuncinci 2″ kwindawo evulekileyo efunwayo kucango (kwaye ngaphakathi kobude obuvumelekileyo bekhebula) ukunqanda iingcango ekuhambeni kakhulu. (Jonga umfanekiso woku-1)
Ucango lunesitshixo esiqinileyo esinobude obuncinci obuveziweyo obuyi-4.5” kwicala lomsebenzisi.Ukucocwa ubuncinane kwe-12 "ngokuthe tye ukusuka kwicala lomnyango (okanye 9" ukusuka ekupheleni kwe-shaft), kunye ne-24" ngokuthe nkqo ngaphantsi kwe-shaft. Kukho indawo eyaneleyo yenkxaso yesakhiwo ukufaka ngokukhuselekileyo isibiyeli sokuxhoma ingalo yetorque, ingalo yetorque kunye nebhokisi yokuhlangana. Ukufumana iinkcukacha ezithe vetshe, jonga imiyalelo yokufaka yokunyuswa Umzobo: 1 & 7.
Indawo yokunyusa iPhaneli yoLawulo (Min. 5 ft. ukusuka kumgangatho ophantsi, kwindawo ecacileyo yomnyango kodwa ekude ngokwaneleyo ukukhusela abasebenzisi ukuba baqhagamshelane neendawo ezihambayo).INdawo yokuNyusa i-Operator/Encoder
Lo mqhubi une-encoder yendawo efakwe phezulu kwibhokisi yegiya. Oku kuvumela ukunyuswa komsebenzisi naphi na ecaleni kobude beshaft apho isithuba sivumayo. Ukunyuka kwasekunene, ukuxhoma-ekhohlo okanye indawo yokunyusela esembindini zonke zamkelekile, kwaye akukho luhlengiso kumsebenzisi, okanye isoftwe yomsebenzisi, efunekayo.
Ukudibanisa i-Torque Arm kwi-Gearbox
Ingalo yetorque kufuneka idityaniswe kwibhokisi yegiya kwelinye icala leencoder kusetyenziswa iibholiti ezi-4 ezivalelweyo. Kukho izithuba ezi-6 ezinokwenzeka zengalo yetorque, kwaye indawo yayo efanelekileyo yokunyuka kufuneka imiselwe kwangaphambili ngaphambi kokuhlanganisana. Qinisa iibholithi ngokufanelekileyo. I-TOQUE ARM LICANDELO ELIPHAMBILI LOKHUSELEKO NOKUSEBENZA KOMSEBENZI KWAYE KUFUNEKA IFAKWA NGOKUKHUSELEKILEYO. Jonga umzobo: 4Jonga umzobo: 4 A malunga neengcebiso malunga nendlela yokunyuswa kwe-Torque Arm kwi-Operator / i-Mounting Bracket ngokumalunga ne-Shaft Off-set.

INDAWO YE-TORQUE YEARM NGOKUQHUMANE NOMSEBENZISI

IMIYALELO YOKUFAKA YOKUFAKA

ISILUMKISO

• UKUNCIPHISA UMNGCIPHEKO WOKWENZAKALA KOMNTU OKANYE UKUFA, MUSA UKUQHAGAMSHELANA AMANDLA OMBANE KUDE KUFIKE I-OPERATOR, IBHOKISI YOKUJONGANA NEPANELI YOLAWULO, ZIKHUSELEKILE KWAYE ZIKHUSELEKILE NGEMIYALELO ELANDELAYO.
• QINISEKISA UKUBA LE NDAWO ICACILE NGABASEBENZI KWAYE KUQINISELWE UKUFIKELELA NGEXA KUFAKA I-OPERATOR.
• SEBENZISA IIPROTOKOLI ZOKHUSELEKO OLUNENEYO NGOKUTSHO KWEEMFUNO ZANGAPHAKATHI, ZASEKHAYA NEZOMTHETHO.

ISINYATHELO ESISINYATHELO LOKUQALA – Nciphisa uFakelo lweBracket
Ukuba ucango lwakho alukaxhotyiswanga nge-bumper/pusher springs, kunyanzelekile ukuba ufakele i-Limit Brackets. Nyusa isibiyeli esinye phezulu kwingoma nganye (Jonga uMfanekiso 1A) ukunqanda ukuhamba ngokungaphaya kocango, kwaye wenze uhlengahlengiso oluzenzekelayo lwe-encoder ngaphambi kokumisela imida nasemva kokulahleka kwamandla. Ezi kufuneka zixhonywe ngaphakathi kwiingcango zocango kweyona ndawo iphezulu yomnyango evumelekileyo yokuhamba, kwaye kufuneka zibekwe kwindawo kanye kanye kuzo zombini iitrekhi ukuze iirola eziphezulu zocango ziphumle ngokuchasene nazo zikwindawo elinganayo.
Ukufakela, vula ngesandla umnyango kwindawo ephezulu yokuvula evumelekileyo ngeentambo, clamp umnyango kwindawo, kwaye ukhusele izibiyeli kumzila njengoko kubonisiwe Umfanekiso we-1A usebenzisa i-roller ephezulu njengeendawo zokubhekisela kwiibakaki.
UKUBA KUNGABIKHO KWE-BUMPER/PUSHER SPRINGS, UKUFAKWA KWEENKCUKACHA ZEMIDA KUYISINYANZELO PHAMBI KOFAKELO LWE-OPERATOR. NGAPHANDLE KWEMIDA YOMZIMBA, UCANGO LUNOKUPHUMA KWIINDLELA ZALO KWAYE KUBANGELE UKWENZAKALA OMNTU OMKHULU KUNYE/OKANYE KUBANGELE UMONAKALO OMNTU OMNXONGO. NGAPHEZULU, AWUKUBA UKWAZI UKUBEKA UMDA.

IKhola yeShaft / i-Bent Key Installation
IKhola yeShaft isebenza njengesiphelo sokumisa isitshixo seshaft esigobileyo ukusithintela ukuba singatyibiliki ngaphandle kwebhokisi yegiya. Kubalulekile ukuba iqiniswe ngokukhuselekileyo ngaphambi kokusetyenziswa komsebenzisi, kwaye idinga ukunyuswa ngokubambisana nesitshixo njengoko kuboniswe kwi-Fig: 5. Lungisa ucango ukuze isitshixo seshaft sijonge phezulu (kunokufuneka uvule/wedge/clamp umnyango uvule kancinci ukuphumeza oku).
Khulula isikrufu seseti yeKhola yeShaft kwaye usityibilikise phezu kweshafti.
Faka iqhosha eligobileyo (elinikezelwe nomsebenzisi) kwiqhosha le-shaft yocango kunye nesiphelo esigobileyo sijonge kwikhola yeshaft kwindawo enqwenelekayo.
Slayidela ikhola ngasemva ukuze ichukumise isitshixo, jonga umfanekiso: 5. Gxininisa ngokuqinileyo isikrufu sekhola kwi-shaft. Qhoboshela i-Torque Arm kwibhokisi yegiya ukuze ijongane nekhola yeshaft xa uyifakela kwaye ikwindawo efanelekileyo njengoko kucetyisiwe kumfanekiso: 4A.
Nceda uqaphele ukuba uhlengahlengiso kwindawo yesitshixo kunye nekhola kunokufuneka ukuba kulungiselelwe ukunyuswa kwengalo yetorque kunye nokuqina.

Ukufakela uMsebenzi
ISILUMKISO
ISILUMKISO: INDIBANO YOMSEBENZISI IYANZIMA KWAYE INOKUBANGA UKWENZAKALA OKUBUNDI OKANYE UKUFA KUFANELE KULAWULWE NGEXESHA LOKUFAKELWA. THATHA ONKE AMAQHINGA OKHUSELEKO ABALULEKILEYO UKUNQANDA UKULAHLISA I-OPERATOR (okt, YIBATHA/YIBOPHE PHANSI) PHAMBI KOKUZAMELA UKUFAKE. I-SCAFFOLDING OKANYE I-SCISSOR-LIFTS/ I-PLATFORM-LIFTS IYACEBISWA UKUFAKELWA KWE-OPERATOR. UNGAZE UZAMA UKUFAKA I-OPERATOR PHEZU KWENQANABA LELISO OKANYE UKUSUKA KWILELI.
QINISEKISA UKUBA AMANYATHELO ANGAPHAMBILI OKUFAKWA KWE-SHAFT COLLAR/UKUFAKWA OKUQINISEKILEYO ALANDELWE NGOKUFANELEKILEYO PHAMBI KOKUBA UQHUBE. UKUNGAPHUMELELI UKWENZA NJENGOKO KUNOKUKUBANGALISA UMONAKALO KWI-ENCODER NGEXESHA LOKUFAKWA KWE-OPERATOR.
Ukulungelelanisa isitshixo sebhokisi yegiya kunye nesitshixo esifakwe ngaphambili (jonga i-Key Shaft Collar / Key Installation kwiphepha langaphambili) ebekwe kwicala lokunyuka kwe-shaft.
Slayidela i-gearbox kwi-shaft ide idibane nokugoba kweSitshixo se-Shaft.
Hlanganisa i-Torque Arm Bracket kwingalo yeTorque usebenzisa i-fastener enikeziweyo. PHAWULA: SUKUQINISA INUTHI NGOKUPHELELEYO). Gcoba i-Torque Arm Bracket kwinkxaso yesakhiwo esiluqilima.
Qinisa ingalo yetorque kwinkxaso yesakhiwo ngokusebenzisa ibholithi ebonelelweyo, i-nut yokutshixa kunye neewasha. Isibiyeli esibonelelweyo sinokufuneka. Ukuba ingalo yetorque ayihambelani nenkxaso yolwakhiwo, unokuzama ukuhlengahlengisa indawo yengalo yetorque kwibhokisi yegiya (jonga ukuHlanganisa iTorque Arm kwibhokisi yeGear) ngokufanelekileyo okanye usebenzise iTorque Arm Bracket.UKUNGAPHUMELELI UKUQINISWA NGOKUKHUSELEKILEYO KWENKOLO YETOQUE KUNOKUKUBANGALELA KUMONAKALO, UKWENZAKALELA OMBUNZI OKANYE UKUFA KWAYE KUYA KUSIPHUMA ISIQINISEKISO.

Ukunyuswa kwebhokisi yeNxulumano
Ibhokisi yokuhlangana iqulethe iitheminali zoqhagamshelwano lwamandla, kunye nebhetri / uqhagamshelwano lonxibelelwano lwephaneli yokulawula. Ukunyusa ibhokisi ye-junction, ngeendlela zokukhwela iiflange kwaye ngokuhambelana nekhowudi yombane, kwindawo ebonakalayo eya kubonelela ukufikelela kuzo zombini amandla ombane kunye nokudibanisa i-wiring panel. Ibhokisi yesiphambuka ifakwe ngaphambili ngeemitha ezi-2 ze-conduit eguquguqukayo, ukuba ubude obude buyafuneka, dibana nomzi-mveliso. Musa ukuyixhoma ibhokisi yesiphambuka kufutshane neendawo ezihambayo okanye kwindawo engafikelelekiyo.Ukufakwa kwePaneli yoLawulo
Iphaneli yokulawula kufuneka ifakwe ngokukhuselekileyo kwinqanaba leliso okanye lijikeleze (ubuncinci be-5 ft ukusuka kumgangatho) kwicala elifanayo kunye nomqhubi / ibhokisi ye-junction. Qinisekisa ukuba indawo yolawulo ixhonywe kude ngokwaneleyo ukusuka emnyango ukuze uthintele ukunxibelelana komsebenzisi nomnyango ngelixa usebenza, kodwa ivale ngokwaneleyo ukuba umsebenzisi acacelwe. view yomnyango ngamaxesha onke. Izibiyeli ezine (4) zokulawula zokuxhoma zibonelelwe ukuququzelela ukunyuswa. Jonga umzobo:8Ifoto-Iliso okanye i-Thru-Beam Sensor Mounting
Isivamvo se-photo-eye esibandakanyiweyo okanye i-thru-beam sensor kufuneka sixhonywe ukuze sihlole indawo egubungela ububanzi bomnyango kumphakamo ongekho ngaphezulu kwe-intshi ezi-6 ukusuka emhlabeni. I-sensor (i-reflective photo-eye) okanye i-reflective (i-thru-beam) kufuneka ifakwe kwicala lomsebenzisi (njengoko iya kufakwe kwipaneli yokulawula), ngelixa isibonisi okanye isidluliseli kufuneka sifakwe kwelinye icala lomnyango, ejongene nenzwa / umamkeli ukuze iziko layo lidibane nomqadi. Sebenzisa isibiyeli sokuxhoma esibandakanyiweyo ukukhusela nokuba ziingoma zocango okanye eludongeni. Jonga kwiinkcukacha ezithile zokunyusela ezinikwe ngoluvo. Ukulungelelaniswa kokugqibela kwenzwa, faka iyunithi kwi-STARTUP MENU (jonga kwiphepha le-18) ukusebenzisa amandla kwi-sensor (emva kwe-WIRING - jonga iphepha le-13 kwi-diagram yocingo olongezelelweyo). Nje ukuba ilungelelaniswe kakuhle kwi-STARTUP MENU, isalathisi siya kukhanya ekuqinisekiseni. Qaphela ukuba xa uphuma kwi-STARTUP MENU, i-sensor iya kusebenza kuphela xa umnyango uvala.
Jonga umzobo: 9 ngereferensi yokunyusela.

IMIYALELO YOKUFAKA

ISILUMKISO
UKUNCIPHISA UMNGCIPHEKO WOKWENZAKALA OKANYE UKUFA, UKUQINISEKISA UKUBA ELA IMIQATHANGO ELALANDELAYO ELANDELWE PHAMBI KOKWENZIWA KOQHAGAMSHELO LOMbane:

1. Susa umbane kwibhokisi yefuse/umthombo kwaye ulandele utshixo olufanelekileyo/tagIinkqubo zokuphuma ngokweekhowudi zombane zelizwe nezengingqi.
2. Qinisekisa ukuba lonke uqhagamshelo lombane lwenziwa ngamagcisa ombane/amagcisa afanelekileyo kuphela kwaye ahlangabezane neekhowudi zombane zelizwe nezengingqi.
3. Zonke iintambo kufuneka zibe kwisekethe ezinikeleyo kwaye zikhuselwe ngokufanelekileyo.

Uqhagamshelwano lweBhokisi yeNxulumano
Izikhululo ezingaphakathi kwibhokisi yokudityaniswa zibhaliwe kwaye zibonelelwa ngamandla egalelo (100-240Vac 1 Ph), kunye nokudibanisa amandla okugcinwa kwebhetri, kunye nokubonelela ngevolthi ephantsi.tage amandla kunye nonxibelelwano lwephaneli yolawulo. Iitheminali ozikhethelayo zikwabonelelwe ngokuVula ngokuPheleleyo uMda wokuSeta ngokutsha uqhagamshelo kwiswitshi yangaphandle njengenye indlela yokusebenzisa i-Limit Brackets njengoseta ngokutsha lwe-encoder.
UQhagamshelwano lwaMandla (100-240Vac Single Phase)

1. QINISEKISA AMANDLA AYAXHOMISWA!
2.  Qhuba iingcingo zombane kwibhokisi yokudibanisa ngokuhambelana nemigaqo yasekhaya neyesizwe.
3. Xhuma amandla angenayo kwi-L / L1 kunye ne-N / L2, kwaye uqinisekise ukuba ucingo lomhlaba lufakwe ngokufanelekileyo.

UQhagamshelo lwePhaneli yoLawulo (24Vdc)

1. Ukusebenzisa ubuncinane bekhebula le-18AWG, qhagamshela iingcingo zomntu ngamnye kwi-V +, GM, GS kunye ne-COM terminals kwibhokisi ye-junction. I-iControls icebisa ukuba usebenzise ikiti yokufaka iintambo (Ingxenye # PDC-CABKIT) okanye ilingana.
2. Ezi ziyakuthelekisa udibaniso kwiPaneli yoLawulo kwaye ziya kupheliswa kulandelelwano olufanayo (njengoko kubhaliwe) ukutshatisa ibhokisi yesiphambuka (zonke iintambo zolawulo lwendawo yolawulo ziyakungena ngapha komzantsi wendawo ebiyelweyo).

Uqhagamshelo lwebhetri (24Vdc) Iibhetri ezi-2 eziQhagamshelwe kuthotho

1. Ukusebenzisa ubuncinane i-18 AWG yocingo olugqunyiweyo; qhagamshela kwi-B + kunye ne-B- ngaphakathi kwebhokisi ye-junction (iingcingo ezimbini ezihlukeneyo). QAPHELA: I-14AWG iyacetyiswa kwi-PULSE 1000 Operators.
2. Ezi ngcingo kufuneka ziqhutywe kunye noQhagamshelwano lwePhaneli yoLawulo (ukudlula ezantsi kwendawo ebiyelweyo) kwaye uqhagamshele kwi-'+' kunye '-'DRIVE iitheminali ebhodini.
3. Beka iibhetri kwiPhaneli yoLawulo. Qhagamshela iingcingo kwiibhetri: i-red lead idibanisa phakathi kwe-'Battery +' tab ebhodini kunye ne-red tab kwibhetri, i-blue lead phakathi kwe-'Battery-' tab ebhodini kunye ne-black tab ebhetrini.

Vula ngokuPheleleyo uQhagamshelwano loTshintsho loMda woMda (24Vdc) (Ngokhetho lwe-H1 & ne-H2 yeSigqibo)

1. Ukusebenzisa ubuncinane i-18 AWG yocingo olugqunyiweyo; qhagamshela kwi-H1 kunye ne-H2 ngaphakathi kwebhokisi ye-junction (iingcingo ezimbini ezahlukeneyo)
2. Qhagamshela ezi ngcingo NGOKUNGEKHO uQhagamshelwano loTshintsho lweLimit, iSensor yokusondela, iReed Switch, njl. njl., isetelwe ukuba isebenze kowona mda uphezulu wocango. Oku kusetyenziswa kwangaphambili kwimida yokumisa ngokomzimba (izibiyeli eziqingqiweyo) ukuseta ngokutsha ikhowudi yokufaka ikhowudi ekuqaleni okanye ukusetwa ngokutsha kwemenyu (indawo evuleke ngokupheleleyo) kunye nokuphepha iirola ezidibaneni nezibiyeli. Ikwasetyenziswa njenge Vula ngokuPheleleyo useto lwendawo kwiMenu. Qaphela ukuba ufakelo lwezibiyeli zomda (okanye esinye isixhobo esibambekayo sokumisa) kusanyanzelekile njengesithintelo sokhuseleko esingafunekiyo xa kukho ukusilela kokutshintsha, kodwa kunokunyuswa umva ukusuka kwiswitshi ukunqanda impembelelo yerola. Ukuba usebenzisa iswitsha yangaphandle endaweni yezibiyeli eziqingqiweyo zokuSeta ngokutsha iNdawo ngokuPheleleyo, useto lwemenyu kufuneka lutshintshwe. Jonga kwiPhepha lama-23.

IBhodi yoLawulo yoQhagamshelwano
Iphaneli yoLawulo ibonelela ngamandla kunye negalelo kwiZixhobo zakho zokuBuyisa (ukuya kuthi ga kwi-3), iZixhobo zokuSebenza (ukuya kuthi ga kwi-2), kunye neSikhululo seQhosha esinentambo, kunye neRemote Radio Receiver. Iireyilayi ezimbini ezikwibhodi zibonelela ngophawu kwiinketho ezahlukeneyo ezicwangcisiweyo. Uqhagamshelo olongezelelweyo luyafumaneka kwiiMpawu zeTrafikhi, i-buzzer kunye ne-Amber edanyazayo isignali (ngelixa ucango lusashukuma) kunye nesitshixo sokutshixa ucango (luthintela ucango ukuba luhambe ngelixa luvuliwe). Isixhobo sokwamkela izixhobo zeperipheral ze-IControls (i-sensor yempembelelo/i-tilt, i-edge ebuyela umva, njl.njl.) nayo inikezelwe.
Ukubuyisela umva izixhobo
I-Pulse yamkela i-UL325 i-Monitored Devices, kunye neZixhobo eziqhelekileyo ezingajongwanga. Qhagamshela ifoto-eye ebonisiweyo kwitheminali ebhalwe '1'. Nayiphi na i-UL325 'ebekwe esweni' isixhobo esibuyisela umva kufuneka siqhagamshelwe kwitheminali ebhalwe '2'. Nawuphi na omnye umgangatho owongeziweyo obuyisela umva ifoto-amehlo, iikhethini ezikhanyayo kunye neekona ezibuyela umva kufuneka ziqhagamshelwe kwitheminali ebhalwe '3'. Landela imizobo yocingo ebandakanyiweyo kule ncwadana, kunye nemiyalelo yokufakela enikelwe kunye nesixhobo sakho sokubuyisela umva ukuze uxhonywe ngakumbi kunye neenkcukacha zoqhagamshelwano. Nceda uqaphele ukuba ngaphandle kwesixhobo esiqhagamshelweyo, esisebenzayo sokubuyisela umva nokuba yi-R1 okanye i-R2, iSibali-xesha sokuVala kunye neempawu zokuvala ngokuzenzekelayo zocango zicinywe – Push/Bamba ukuVala iiprotocol ziya kuqaliswa.
Izixhobo zokuSebenza
Izixhobo ezizenzekelayo, ezisebenza ngeengcingo, ezifana ne-Floor Loop Detectors, i-Tlall Cords, i-Motion Detectors kunye ne-Photo-Eyes (ukuya kubuninzi bezixhobo ezi-2 ezinengcingo) ezisetyenziselwa ukuvula umnyango ziqhagamshelwe apha. Landela umzobo wocingo ongezantsi kwaye ubhekisele kwimiyalelo enikelwe ngesixhobo sakho sokuvula ukuze ufumane uqhagamshelwano oluchanekileyo kunye neenkcukacha zokuxhoma. Qaphela ukuba zonke izixhobo eziqhagamshelwe kwi-terminal A1 ziya kuvula ucango kwindawo nje eneentloni zobude obugcweleyo bokuvula, kwaye izixhobo eziqhagamshelwe kwi-terminal A2 ziya kuvula ucango kumda omiselweyo.
Cofa iqhosha lesiKhululo
Qhagamshela isitishi seQhosha elongezelelweyo kwelinye icala lomnyango wakho usebenzisa la magalelo. AKUKHO abafowunelwa abomileyo abafunekayo. Qaphela ukuba iZitishi zeQhosha lokucofa zinokucwangciswa ukuphakamisa ucango kwindawo evuleke ngokupheleleyo okanye emiselwe umda. Jonga kwidayagram yocingo ngeenkcukacha ezithe vetshe zoqhagamshelo. Izikhululo zeqhosha lokucofa ziyafumaneka kwa-RW, nceda uqhagamshelane nathi ngeenkcukacha.
Irediyo ekude
Qhagamshela umamkeli wakho kwiitheminali ezibonelelweyo - njengoko indawo ebiyelweyo yolawulo lwePulse ingeyontsimbi, i-eriyali yangaphandle ayifuneki ngokuyimfuneko. Qaphela ukuba iRemote Radio inokucwangciswa ukuphakamisa ucango ukuba luvuleke ngokupheleleyo, okanye lusete indawo emiselweyo. Jonga kwidayagram yocingo ngeenkcukacha ezithe vetshe zoqhagamshelo. Abathumeli berediyo abakude kunye nabamkeli bayafumaneka kwi-iControls, nceda uqhagamshelane nathi ngeenkcukacha.
Isitshixo samacango
Ezi terminals ziyafumaneka ukucima ukusebenza komnyango, nokuba kukutshintsha okulula, okanye inzwa ebonelela ngomqondiso xa ucango luvaliwe ebusuku. Olunye ukhetho olukhoyo kukudibanisa oku kwisilayidi-xesha esicwangcisiweyo ukuvumela ukusebenza kocango lweshedyuli esele imiselwe. Jonga kwidayagram yocingo ngeenkcukacha ezithe vetshe zoqhagamshelo. Qhagamshelana ne-IControls ngolwazi malunga neKit yeSensor ye-Door Lock yabo.
Irobhothi
Ukufakela i-LED stop kwaye uhambe ukukhanya, sebenzisa ii-terminals ezibonelelweyo phantsi kwebhodi. Ebomvu iqhagamshela kwitheminali 'R', eluhlaza iqhagamshela kwitheminali 'G' kwaye eqhelekileyo kufuneka ifakwe kwitheminali '+24'. Qinisekisa ukuba usebenzisa izibane zetrafikhi ze-LED (kungekhona i-incandescent) ezinobuninzi bokusetyenziswa okungekho ngaphezu kwe-100mA. Irobhothi iya kuhlala ibomvu xa ucango luhamba okanye luvaliwe, kwaye luya kuba luhlaza kwindawo evuleke ngokupheleleyo kuphela. Umbala obomvu unokucwangciswa ukuba udanyaze xa ucango lushukuma, kwaye kwangaphambi kokuvalwa xa usebenzisa isibali-xesha sokuvala (Jonga iPhepha 22 ngeenkcukacha ezithe vetshe). Itheminali 'Y' yeyesibini esidanyazayo sebhakana ye-Amber kunye/okanye isignali evakalayo ukubonisa xa ucango lushukuma. Ngelixa ufikelela kwiMenu yokuSeta, iirobhothi ziya kucima, kwaye i-Amber beacon, ukuba ifakiwe, iya kudanyaza. I-LED Stop kunye ne-Go Lights esuka kwi-IControls icetyiswa kakhulu, nceda uqhagamshelane nathi ngeenkcukacha. Jonga kwidayagram yocingo ngeenkcukacha ezithe vetshe zoqhagamshelo.
Qaphela: SUKUZISEBENZISA IIMPAWU EZINGAHLAZIYO KUNYE NOMSEBENZISI. IZIbane ze-LED KUPHELA.
Uqhagamshelo loNxibelelwano lweNtshukumo
Uqhagamshelo lwe-NO kunye ne-NC relay output lubonelelwe ukuze ludibane nezinye izixhobo zokuphatha izinto (okt isixokelelwano sedokhi) okanye iinkqubo zokhuseleko/zomlilo. Ezi ziphumo zinokucwangciswa (jonga uSeto lwe-Output Relay) ukunika amandla xa ucango lukuMda oVulekileyo okanye oValiweyo. Jonga kumzobo wocingo ukuze ufumane imiyalelo engaphezulu.

IMIZOBE YOKUFAKA

Iphaneli yokulawula yeeModeli 500, 750 & 1000IZIXHOBO ZOKUSEBENZA NGOKUKHETHA
PHAWULA: 

1. XA KUQHAGAMSHELWA ISIKHULULO SESIQINISO, SUSA IFEKTRI EFAKIWEYO IJUMPA PHAKATHI kuka-(+24) KUNYE NEZI-(S)
2. Igalelo (A1) LIVULA UCANGO NGOKUGQIBELELEYO, I-INGTO EYI-A2 LIVULA UMCANGO NGOKUSETYENZISWA KOMDA.
3. IREYIYO EKUDE KUNYE NEBHABHU LOKUTYHALA IBHAYIBHILE ZIYIMENU EQINISEKIWEYO UKUVULA UCANGO NGOKUGQIBELELEYO OKANYE NGOKUSETYENZISWA KOMDA.
4. UKUBA ISIXA-MALI SOKUVALA ISETHELWE KUZIRO ZONKE IZIQINISEKISO “EZIVILEYO” SEBENZA IVILEYO/IVALEYO

IZIXHOBO EZIKHETHAYO EZINCEDAUKUKHETHA IZIXHOBO ZOKUBUYISAAMANQAKU: Qhagamshela iziXhobo eziBuyiselwa umva ezingaBekwanga kwi-R3 ukongeza kwisixhobo esisebenzayo esiqhagamshelwe kwi-R1 okanye i-R2. Ukuba usebenzisa i-Monitored Reversing Device kwi-R2, i-R1 kufuneka iqhagamshelwe kwisixhobo esisebenzayo okanye itsibe nge-P+.ILISO LWE-2-WIRE NGE-BEAM SENSOR VITECTOR RAY-N
Umzobo wocingoILISO LWE-2-WIRE NGE-BEAM VITECTOR OPTOΕΥΕ (ΝΕΜΑ 4Χ)
Umzobo wocingo

INKQUBO YOKUQALA

ISILUMKO!
Ngaphambi kokusebenzisa amandla kumqhubi wePulse, qinisekisa ukuba iyunithi ibekwe ngokuqinileyo kwi-shaft yomnyango kwaye iqiniswe ngokukhuselekileyo kwingalo ye-torque / bolt. Kwakhona ukuba izibiyeli zeLimit zikhona nokuba i-encoder ibotshelelwe kakuhle kwibhokisi yegiya.
UVAVANYO LOCANGO LWENKCAZELO ENTSHAKO 
ELI NYATHELO MELE LENZE PHAMBI KOKUQHAKAMISWA KWAMANDLA.
Umsebenzisi wePulse wenzelwe ukusetyenziswa kuphela ngeengcango ezilinganayo. Iingcango ezingafanelekanga zinokuchaphazela kakhulu ukusebenza komsebenzisi. Sincoma ukuba xa ucango kunye nomsebenzisi zifakwe ngokupheleleyo ukuba uvavanye ibhalansi yocango phambi kokunyusa amandla.
Ukwenza oku, qinisekisa ukuba iibhetri ziqhagamshelwe, amandla acinyiwe, kwaye uzame umjikelo omnye opheleleyo phezulu naphantsi phantsi kwamandla ebhetri (cofa kwaye ubambe iqhosha VULA, kwaye ucofe kwaye ubambe iqhosha elithi CLOSE). Ucango kufuneka luhambe ngesantya esicothayo, esizinzileyo ukuya phezulu nasezantsi. Ukuba ucango lunokufikelela kumjikelo opheleleyo phantsi kwamandla ebhetri, lusetwa ngokufanelekileyo ukuze lusetyenziswe nomsebenzisi wePulse. Ukuba ibhetri ayinako ukuluhambisa ngokupheleleyo ucango kulo naliphi na icala, ukucinezeleka kwasentwasahlobo elucangweni kufuneka kuhlengahlengiswe.
AMANDLA PHEZULU
Faka amandla kwiyunithi. Iphaneli yokulawula i-LED Screen kufuneka ikhanyise kwaye iqhube ukuzixilonga. Ukuba isikrini se-LCD asikhanyiswanga, jonga ku- Trouble Shooting kwiPhepha 25. Xa sele igqibile ukuzixilonga, isikrini siya kufundeka 'Door is Ready'. UNGAZAMI UKUVULA UCANGO EMVA KOKWENZA IMANDLA YOKUQALA- FIKELELA IMENU YOKUQALA KUPHELA!

QALISA IMENU & UFIKELE KUZO ZONKE IIKHETHA ZEMENU
QAPHELA UKUBA ZONKE IZILUNGISEKO ZEMENU YEFACTORY ZIYCETYISWA KUMACANGO AMAQANDO KUPHELA. QHAGAMSHELANA NE-iCONTROLS EZISENYE IZIMBO ZEMICANGO (okt. Rolling Steel, njl.) Ukufikelela kwi- STARTUP MENU cofa kwaye ubambe iQINISO LOKUMISA IMIZUZWANA eyi-10 - ungakhuphi de kuvele amagama 'QALA IMENU' kwisikrini.
Nje ukuba ugqibile, ungaskrola phakathi kweenketho ezahlukeneyo zokuQALA IMENU ngokucinezela i-VULA kunye namaqhosha. Nje ukuba ufikelele kukhetho ongathanda ukuluguqula, cofa iqhosha elithi YIMA. Sebenzisa i-VULA kunye ne-CALA amaqhosha ukuskrola/ukuguqula phakathi kokhetho phakathi kokhetho, kwaye emva koko ucinezele YIMA ukugcina ukhetho lwakho kwaye ubuyele kwi- STARTUP MENU.
UKUVALA ISIXA
AKUNCEBISWA UKUSETA ISIXA-MALI SOKUVALA KUDE EMVA kokuba IYUNITHI IVAVANYWE NGOKUPHELELEYO.
Isibali-xesha sokuvala siza kuvala ucango ngokuzenzekelayo emva kokuvula ngenani elimiselweyo lemizuzwana ecwangcisiweyo kusetyenziswa olu khetho lwe STARTUP MENU.Nje ukuba ufikelele kolu khetho, sebenzisa i-VULA kunye ne-CLOSE amaqhosha ukwandisa okanye ukunciphisa ixabiso lexesha lokuvala kwi-1 yexesha lesibini. Ukuba ayifunwa, qinisekisa ukuba Isibali-xesha sokuVala sisetiwe UKUVALA. Ukuba iyafuneka, yibeke kulo naliphi na inani lemizuzwana ukusuka ku-1 ukuya ku-99. Khumbula ukuba eli linani lemizuzwana apho ucango luya kuhlala luvuliwe phambi kokuba luvale ngokuzenzekelayo. Cofa iqhosha elithi STOP ukugcina ixabiso kwaye ubuyele kwiMENU YOCWANGCISO.Isibali-xesha sokuvala siya kuvalwa xa isixhobo sokubuyisela umva sisilele, kwaye iPush manual kunye neBamba ukuVala iiprothokholi ziya kusebenza kwimisebenzi yokuvala umnyango.

UMQULUTAGUHLU
PHAWULA: UKUSEBENZISA UMQULU ONGACHAPHAZANGATAGUKUSEKWA KUNOKUKHOKELELA EKUSEBENENI KOMNYANGO NGENXANISO ENGAKHUSELEKANGA.
Lo msebenzisi uyilelwe ukusebenza ngeSIGABA ESINYE voltages ukusuka 110-240Vac (ye-3 isigaba voltage, sebenzisa i-transformer yangaphandle ekhethiweyo). Kukho iisetingi ezi-2 ezikhoyo, i-110130V okanye i-208-240V, kwaye ukhetho olufanelekileyo lokufakela kwakho KUFUNEKA lwenziwe ngaphambi kokuba
ukusebenza. Ukungaphumeleli ukwenza oko kunokubangela umonakalo kumqhubi kunye nomnyango. Ukufikelela kolu khetho, cofa phakathi kweenketho zemenu usebenzisa i VULA okanye CALA amaqhosha de kube VOLTAGI-E SETUP ivela kwisikrini. Emva koko cofa iqhosha elithi STOP ukuze ukhethe. Cofa IVULA okanye CALA ukuze utshintshe phakathi kweVoltage Ukukhetha. Cofa u-MISA ukuGcina kwaye ubuyele kwi- STARTUP MENU.IMIDA YOCANGO
PHAWULA: UKULUNGISWA KWEMIDA KUFUNEKA KWENZIWE NGABASEBENZI ABAQEQESHWE KUPHELA. I-ENCODER IYA KUYIGCINA LE MIDA IDE IPHINDE UHLANGANISIWE. Fikelela kwi DOOR LIMITS ukhetho oluvela kwi-STARTUP MENU kwaye ucinezele iqhosha elithi STOP. Xa sele ikhethiwe, isihloko se-DOOR LIMITS siya kuvela kunye nomyalelo othi 'Tyhala VULA ukuze uqalise'. Cofa iqhosha le-VULA, kwaye umnyango uya kuvula indawo evuleke ngokupheleleyo ngokuchasene neZibiyeli zoMda (okanye ide idibanise iqhosha eliqhagamshelwe kwii-terminals ze-H1 kunye ne-H2 - jonga i-Junction Box Connections kwiPhepha le-10). QINISEKISA UKUBA IIROLI EZINGAPHEZULU ZOCANGO ZIPHUMILE NGOKUCHASANA NEZIBAKASHI ZOKUDA. Umda ovuliweyo ngoku ufuna ukusetwa.
WEKA UMDA OVULAYOCofa u-CLOSE (VULA ukusebenza ukuba unokudubuleka ngaphezulu kwendawo oyifunayo) ukubaleka ucango ukuya kubude obufunwayo boMda ovulekileyo. Isetingi eVulekileyo yoMda kufuneka ibe bubuncinci obususela kwi-2″ ukusuka kwi-Limit Bracket okanye i-Open Limit switch. Cofa iqhosha elithi MISA ukugcina uMda oVulekileyo kwaye uhambele phambili UKUSETHA UMDA.
CINGA UMDAUkusuka kuMda oVulekileyo, baleka uye kwindawo efunwayo Vala, usebenzisa i CLOSE iqhosha (VULA ikhona ukuze ulungise kakuhle). Qinisekisa ukuba umnyango uvalwe ngokufanelekileyo emazantsi. Cofa iqhosha elithi STOP ukugcina nokubuyela kwi-STARTUP MENU.
UKUBEKA IMICANGO NGENGXAPHO
Kuseto lokuqala nceda sebenzisa isantya esiphakathi sasefektri se '3' okanye esicothayo. Njengoko kuphawuliwe ngezantsi kweMotor, uCango kunye nobukhulu beGubhu kunokuchaphazela isantya sokuvula umnyango kwaye oku kunokuba yiyo yonke into efunekayo. Lungisa isantya ukuya phezulu kuphela emva kokuba uvavanyiwe ngezantya ezisezantsi.
Ii-Pulse Operators ziye zaphuhliswa ngobuchwephesha obufanayo obusetyenziswa kwi-High Speed ​​Doors. Ngelixa kunqunyelwe kwisantya esikhulu sokuvula ukuya ku ~ 24” ngesekondi kwiingcango zecandelo (oku kuxhomekeke kucango, igubu, kunye nomlinganiselo webhokisi yegiya) kunye nesantya esiphezulu sokuvala ukuya ku ~ 16” ngomzuzwana, sicebisa ukuba usete isantya ukuze uvumeleke. neemfuneko zakho zombini, kunye nempahla yomnyango. Ukufumana obona bomi bubude kumnyango wakho, kunye nokwandisa isantya sakho esivumelekileyo, sicebisa ukuba kufakwe iintambo zeStainless Steel kunye neerola zenayiloni ukuba azikho semgangathweni kumnyango wakho.
UKUVULA NGENGXELO
Ukufikelela kwi-Open-Speed ​​Settings, qiniseka ukuba ukwiMENU YOKUQALA (bona imiyalelo engentla), emva koko ujike phakathi kokhetho usebenzisa i-VULA okanye CALA amaqhosha de kuvele isantya sokuvula kwisikrini. Emva koko cofa iqhosha elithi STOP ukufikelela kwaye wenze utshintsho.Umsebenzisi wePulse uyifektri ixhotyiswe ngeenketho ezi-5 zokuseta isantya esivulekileyo, esichongwe njenge-1 (esezantsi) ukuya kwi-5 (ekhawulezayo). Guquguqula phakathi kwezi 5 iinketho ngokusebenzisa i VULA kunye/okanye CACELA amaqhosha, kwaye cinezela i Yima iqhosha xa ukhetho olufunekayo luvela kwi
ikhusi ukugcina nokubuyela kwi STARTUP MENU.
UKUVALA NGENGXELO
Ukufikelela kwiiSetingi zokuvala isantya, qiniseka ukuba ukwiMENU YOKUQALA (bona imiyalelo engentla), emva koko ujike phakathi kweenketho usebenzisa IVULA okanye CALA amaqhosha de kuvele isantya sokuVala kwiscreen. Emva koko cofa iqhosha elithi STOP ukuze ukhethe.Umsebenzisi wePulse uyifektri ixhotyiswe ngeenketho ezi-5 zoseto lwesantya esisondeleyo, ukusuka kwi-1 (esezantsi) ukuya kwi-5 (ekhawulezayo). Guqula phakathi kwezi zi-5 iinketho ngokusebenzisa i-VULA kunye/okanye CARAMA amaqhosha, kwaye ucinezele iqhosha lokumisa nje ukuba ukhetho olufunekayo luvela kwisikrini ukugcina nokubuyela kwi- STARTUP menu.
IMODE YOJONGE
Ukufikelela kwiNkqubo yeJog, qiniseka ukuba ukwiMENU YOKUQALA (bona imiyalelo engentla), emva koko uqhoboshe phakathi kweenketho usebenzisa i-VULA okanye CALA amaqhosha de kuvele Imo yeJog kwisikrini. Emva koko cofa iqhosha elithi STOP ukuqalisa ukusebenzisa.Imowudi yeJog yenza ulawulo lwesandla lomnyango usebenzisa VULA kunye namaqhosha. Ngexesha leMowudi yeJog, yonke imida iyacinywa, kwaye iiprothokholi zokutyhala ziyaqaliswa. Olu khetho lunokusetyenziselwa ukuvavanya ukusebenza komnyango ngaphandle kwe-encoder, ukuqinisekisa ukulingana okufanelekileyo komnyango, okanye njengendlela yokusebenzisa umnyango phantsi kwamandla xa i-encoder ingasebenzi kakuhle. Ucango luya kuhamba kwicala ngalinye kwindawo ethi VULA I-SPEED ESIXOSHA ESIYI-SOLOY SPEED (jonga iPhepha lama-22), ukuze usebenze ngokukhuselekileyo.UKUPHUMA IMENU YOKUQALISA – UKULUNGISWA NOVAVANYO
Ukuphuma kwiMenu yokuQalisa, cofa kwaye ukhulule iqhosha elithi STOP ngelixa uQALA IMENU ivela kwiLCD. Ukuba ulugcinile utshintsho kwisantya somsebenzisi, okanye usete ngokutsha imida, kuya kufuneka ukuba wenze ulungelelwaniso olukhawulezayo lwesixokelelwano. Iingcebiso zesikrini ziya kubonelela ngomyalelo wexesha lokwenyani kwiimfuno zolungelelwaniso. Jonga iPhepha lama-22 ngolwazi oluthe vetshe ngoLungiso. Nje ukuba iCalibration igqitywe okanye ukuba bekungafuneki, isistim iya kuqhuba uxilongo olukhawulezayo, kwaye iLCD kufuneka ibonise ucango olukhoyo (Oluvuliweyo, luvaliwe okanye luyekwe). Uvavanyo locango luyafuneka ngoku.
PHAMBI KOKUBA USEBENZE UCANGO, QINISEKISA UKUBA IZIBAKI ZEMIDA YOCANGO (OKANYE IPUSHER SPRINGS OKANYE UKUTSHINTSHA UMDA) ZIKHONA, KWAYE UMDA WEMICANGO ISELWE.
Vula kwaye uvale umnyango amaxesha ambalwa kwaye uqaphele ukuba umnyango uqhuba kakuhle kwaye umisa kwimida efanelekileyo. Qinisekisa ukuba ucango lusetwe ngezantya ezifunekayo, kwaye uvavanye isixhobo ngasinye sokubuyisela umva nesokuvula ukuqinisekisa ukusebenza kwaso.

Advanced MENU

PHAWULA: EZI NKQUBO KUFUNEKA KUFIKELWE YI-TECHNICIAN EQEQESHIWEYO EMVA KOKUSETSHA NOKUHLOLA OKUQALA, KUPHELA UKUBA KUFUNEKA. Ukufikelela kwi-ADVANCED MENU iinketho cofa kwaye ubambe iQINISO LOKUMISA IMIZUZWANA eyi-10 ngelixa ukwi-QALISA MENU isikrini. Sukukhupha de kuvele i-ADVANCED MENU kwisikrini.
UKUBUYISA ISIXASebenzisa oku ukuseta ixesha elifunekayo lokulibaziseka lokuBuyiswa kocango. Ukuba isixhobo esibuyisela umva okanye umsebenzi uvuliwe xa ucango luvalwa (okt. ifoto-eye, ivamngiswa yomthwalo, njl.njl.) ucango luya kunqumama ngexesha elimisiweyo elibonisiweyo.
Khetha phakathi kwe-0.5, 1.0, 1.5 imizuzwana, okanye ucime. Ukuba LUVALIWE, ucango aluyi kubuya umva, kodwa luhlale lukhona de ungenelelo lomsebenzisi (Oku kuyacetyiswa xa usebenzisa Isibali-xesha sokuvala). Cofa u- STOP ukugcina olu Seto kwaye ubuyele kwi-ADVANCED MENU.
RWonke amaxeshaOlu Seto luvumela umsebenzisi ukuba atshintshe amaxesha okusebenza kwemoto phakathi kwe-2.4 kHz, 12kHz kunye ne-20kHz. Iifrikhwensi ezithile zinokuphazamisana nezixhobo zomntu wesithathu okanye zibangele ingxolo ephezulu kunye nohlengahlengiso lunokufuneka. Ukumiselwa komzi-mveliso kumiselwe kwi-12kHz. Musa ukulutshintsha olu seto ngaphandle kokuba ucetyiswe yiNkxaso yobuGcisa.
IBRAKE YEDYNAMICKumacango anokubanzima kunomgangatho okanye abe nemithombo engafanelekanga ebangela ukuvaleka okuphezulu, lo msebenzisi uneeKhetho zeDynamic Braking. Ukuba ucango alucothi ngokubonakalayo ngexesha 'lokumisa okuthambileyo' (malunga nonyawo lokugqibela lohambo), kusenokwenzeka ukuba ucango luya kufuna imbuyekezo ye-dynamic braking.
Ukungagqibeki komzi-mveliso yeyokungabikho kwe-Dynamic Braking (OFF), kwaye kuyacetyiswa ukuba kusetyenzwe ngokusemgangathweni. Ukuba i-Dynamic Braking ingqineke iyimfuneko, cofa i-VULA/ CABA amaqhosha ukuguqula phakathi kokhetho (Phantsi, Phakathi & Phezulu).Qaphela ukuba ukongezwa kwe-Dynamic Braking yenzelwe ukunceda iingcango ezine-inetia ephezulu ekuphumezeni 'ukumisa okuthambileyo'. Kucetyiswa ukuba phambi kokuseta i-Dynamic Braking, uqale uvavanye ucango ngesantya esisezantsi sokuvala. Ukusilela koku, xa useta i-Dynamic Braking kufuneka uqale nge-LOW yokuseta kuqala, kwaye uvavanye umnyango. Ukuba kufuneka i-braking eyongezelelweyo, yiya kwi-MEDIUM useto kunye novavanyo, kunye neseto ephezulu. Ukuba uqaphela ukuba ucango lwenza intshukumo 'yokuxhuzula' kufutshane nomzantsi wohambo lwalo, ukusetwa kuphezulu kakhulu, kwaye kufuneka kuthotywe.
UKUVULA UMNYANGO
Ukuba ucango luthintelwe ekuvulekeni (okt. ngenxa yokwakhiwa komkhenkce, i-latch yocango ibandakanyeka, njl. njl.) olu phawu lwangoku lokubeka iliso luya kumisa umnyango ukukhusela umonakalo. Ubuzaza bolu qwalaselo lungatshintshwa kolu cwangciso, okanye uphawu lunokuvalwa ngokupheleleyo.I-Opening Force sensitivity inokulungiswa ukusuka kwi-1-20 (i-1 ibaluleke kakhulu kwizithintelo / iijam / ukungalingani) okanye OFF. Ukumiselwa komzi-mveliso ngu-'5'.
UKUVALA UMNYANGO
Ukuba ucango luvalekile ukuba luvale (okt ngenxa yokuphazamiseka, i-jam, njl.) olu phawu lwangoku lokubeka iliso luya kumisa kwaye luhlehlise ucango ukuthintela umonakalo. Ubuzaza bolu qwalaselo lungatshintshwa kolu cwangciso, okanye uphawu lunokuvalwa ngokupheleleyo.Ukuvala Uvakalelo lwamandla lunokulungelelaniswa ukusuka kwi-1-20 (i-1 ibaluleke kakhulu kwizithintelo / iijam / ukungalingani) okanye OFF. Ukumiselwa komzi-mveliso ngu-'3'.
VULA NGENXA YESIXEKOXa umnyango usondela kumda ovulekileyo kwaye unciphisa isantya ukuya kwisantya esicothayo ngaphambi kokumisa (i-Soft Stop), amandla ongezelelweyo / isantya sinokufuneka ukugqiba ukuvula. Ngelixa oku kubonisa ucango olungafanelekanga, olu phawu lungasetyenziselwa ukubuyisela. Olu seto kufuneka lutshintshwe kuphela ukusuka kwi-NORMAL ukuya kwiseto ESIPHAKAMILEYO ukuba ucango alulungelelaniswanga ekuhambeni kwexesha kwaye aluhambi ngokupheleleyo ukuya kuVula umda. Ukuba lufakelo olutsha, ukutshintsha ukunyanzeliswa kwentwasahlobo kwibhalansi efanelekileyo linyathelo lokuqala elifunekayo. Ukumiselwa komzi-mveliso 'KUQHELEKILEYO'.
VALA NGENXA ECOTHAYOXa ucango lusondela Vala uMda kwaye wehlisele phantsi kwisantya esicothayo ngaphambi kokumisa (I-Soft Stop), amandla ongezelelweyo / isantya sinokufuneka ukugqiba ukuvala. Ngelixa oku kubonisa ucango olungafanelekanga, olu phawu lungasetyenziselwa ukubuyisela. Olu seto kufuneka lutshintshwe kuphela ukusuka kwi-NORMAL ukuya kwisicwangciso ESIPHAKAMILEYO ukuba ucango luba nokungalungelelani ixesha kwaye aluhambi ngokupheleleyo ukuya kuVala umda. Ukuba lufakelo olutsha, ukutshintsha ukunyanzeliswa kwentwasahlobo kwibhalansi efanelekileyo linyathelo lokuqala elifunekayo. Ukumiselwa komzi-mveliso 'KUQHELEKILEYO'.
VULA RAMPPHANTSI UMDAEsi seto sisetyenziselwa ukutshintsha indawo apho ucango luqala ukuhla ukuya kwisantya esicothayo njengoko lusondela kuMda oVulekileyo. Umsebenzisi unokukhetha phakathi kwe-auto (eye yaqulunqwa yinkqubo) okanye inani elifunwayo lokujikeleza kwe-shaft (phakathi kwe-0.5 ukujika kunye no-3 ukujika kwi-half rotation increments).
Isetingi yeFactory yalo mboniso yi-AUTO. Oku akufuneki kutshintshwe ngaphandle kokuba kucetyiswa yiPulse Technical Support.
VALA RAMPPHANTSI UMDAEsi sicwangciso sisetyenziselwa ukutshintsha indawo apho ucango luqala ukuhla ngesantya esicothayo njengoko lusondela kuMda wokuVala. Umsebenzisi unokukhetha phakathi kwe-auto (equlunqwe yinkqubo) okanye inani elifunwayo lokujikeleza kwe-shaft (phakathi kwe-0.5 ukujika kunye no-3 ukujika kwi-half rotation increments).
Isetingi yeFactory yalo mboniso yi-AUTO. Oku akufuneki kutshintshwe ngaphandle kokuba kucetyiswa yiPulse Technical Support.
VULA IINKETHO ZOMDA (LIQHOSHA IQHUSHA)Olu seto luvumela umsebenzisi ukuba akhethe phakathi kwe-SET LIMIT okanye UKUVULA NGOKUGCWELELEYO umda weqhosha elithi "VULA" kwiqela lolawulo okanye i-terminal ethi "O" (Push Button Station Inputs) kwibhodi yesekethe yolawulo.
VULA IINKETHO (REMOTE RADIO)Esi sicwangciso sivumela umsebenzisi ukuba akhethe phakathi komda omiselweyo okanye umda ovulekileyo ngokupheleleyo we-"REMOTE RADIO" uxhulumaniso kwibhodi yesiphaluka yolawulo.
IINKETHO ZOKUPHUMELA RELAY
I-Output Relay isetyenziselwa umqondiso / ukudibanisa kunye nezinye izixhobo ezifana ne-dock leveller, izixhobo zokhuseleko, ezinye iingcango, njl. umsebenzisi kolu seto.
UKUSETYENZISWAOlu phawu luyafuneka ukulinganisa imvakalelo yomthwalo. Isikrini sikhokelela kwisikhokelo somsebenzisi ngolungelelwaniso.

QAPHELA: UKUBA UTSHINTSHA NALUPHI NA KWEZI ISETHINGI ZILANDELAYO, I UMSEBENZISI UYA KUKUKUNZA UKUBA UQINISEKISE XA UPHUMA Imenyu: Umqulutage Uluhlu, indawo yeMoto, iMida yamacango, isantya esivulekileyo, isantya sokuvala, isantya sePWM, vula Rampphantsi kwaye Vala uRampphantsi.
UKULINGANISWA KOCANGO KUBANDAKANYA LAMA nyathelo ALANDELAYO: – Umjikelo wokuvula ngokucothayo ngokuzenzekelayo kocango. (Uya kucelwa ukuba uvule umnyango)
– Umjikelo wokuvala umnyango ngesandla. Cinezela kwaye ubambe iqhosha CLOSE kulo mjikelo. Ukuba iqhosha le-CLOSE alibanjwanga de ucango luvalwe ngokupheleleyo, uMsebenzi uza kulahla eli nyathelo kwaye akuxelele ukuba uqalise kwakhona.
-Uya kucelwa ukuba uvule umnyango weCalibrate Opening Force.
– Ukuseta kwakhona i-Encoder. Nje ukuba ucango luvuleke ngokupheleleyo, kuya kufuneka ucinezele u-VULA kwakhona ukuseta kwakhona i-Encoder (Isikrini se-LCD siza kuthi "UCANGO LULUNGILE" njengomyalezo phambi kokuba i-Encoder imiselwe kwakhona.)ISHEDYULI YOLONDOLOZOOlu phawu luseta isikhumbuzi, esiboniswa kwi-LCD, ukucwangcisa ulondolozo emva kwenani elikhethiweyo lemijikelo yabasebenzisi. Ukungagqibeki komzi-mveliso kusetelwe ukwazisa ngoLondolozo emva kwe-250,000 yemijikelo (ecetyiswayo kwiMotor Brush Replacement). Inokwehliswa kwi-1,000 cycle increments. Cinezela i VULA okanye CALA amaqhosha ukutshintsha, kwaye Cofa kwaye ubambe amaqhosha okuskrola ngokukhawuleza kwisetingi yomjikelo ofunekayo.
UKUMENYAZISA OKUBOMVUCwangcisa eli nqaku KUVULIWE ukuba ukhetha isibane esibomvu se-LED Stop encanyathiselwe kunye nokuKhanya kokuKhanya ukuze kudanyaze ngelixa ucango lusashukuma.
I-ADVANCED REDIsetyenziswa ngokudityaniswa ne-CLOSING TIMER (Iphepha 18), olu phawu lokhuseleko lujika ukukhanya okubomvu (okanye ukudanyaza kwesibane esibomvu ukuba olu seto lwenziwe lwasebenza) yokukhanya okuqhotyoshelweyo kwe-LED Stop & GO phambi kokuvalwa kocango ngenombolo ecwangcisiweyo. yemizuzwana. Qaphela ukuba kufuneka ukhethe ixabiso elikhulu kune CLOSING TIMER esetwe kwangaphambili, iyakuqala ngexesha elinye. Umzi-mveliso oMiselweyo luseto luka-'OFF', olunokhetho lwemizuzwana eyi-1-9 ye-ADVANCED RED.
REMOTE REDIO IMODI
Olu seto luvumela iinketho ezimbini zendlela i-remote esebenza ngayo ukuba icinezelwe ngelixa ucango luvuliwe.Kwimo ethi 'Vula/Vala' xa ucofa iqhosha elikude ukusuka kwindawo eValiweyo, ucango luya kuvula isethingi ekhethiweyo yomda (jonga iiKhetho eziVulekileyo zoMda kwiphepha le-14). Ukucofa i-remote kwakhona ngexesha lokuhamba kwayo akuyi kuba nasiphumo. Nje ukuba ifike kwindawo evulekileyo, ukucofa i-remote iya kuyalela ucango ukuba luvale.
Kwimowudi ethi 'Vula/Misa/Vala' ucofa iqhosha elikude xa ucango luvaliwe, ucango luya kuvuleleka kwisetingi ekhethiweyo yomda. Ukuba unokucofa isilawuli kude kwakhona ngexesha lokuvula umjikelo, ucango luyakuyeka. Ukuba icinezelwe kwakhona, iya kuvala ukusuka kwindawo yokumisa.Kuyo nayiphi na imo, ukuba isilawuli-kude sicinezelwe ngelixa ucango luvaliwe, luya kubuya umva.
VULA UMDA WOKUTSHINTSHA
Ukuba ukhetha ukusebenzisa iTshintsho (umda, ukusondela, ingcongolo, njl. njl UKUSEBENZISA UKUTSHINTSHA KUSAFUNA UKUFAKELWA KWEZIBAKASHI ZOMDA NJENGENCINCIKO YOKHUSELEKO KWIXEKO LOKUSILELA UKUTSHINTSHA.
VALA RAMP-UPUKA IXESHAKumjikelezo wokuVala, ukusuka kwindawo evulekileyo, unokuhlengahlengisa ixesha elithatha umnyango ukukhawuleza ukusuka kwindawo yokuphumla ukuya kwisantya esipheleleyo. Oku kunenzuzo ngakumbi xa usebenzisa iingcango zokuphakamisa umgangatho kunye / okanye iigubhu ezinkulu, okanye xa iyunithi ifakwe kwi-balanced rolling door door. Oku kunokulungiswa kwi-0.5s ukunyuka ukusuka kwi-0.5 ukuya kwi-3.0 Imizuzwana. Umzi-mveliso oMiselweyo yi-1.0s
ISIPHUMISO FUMANA IXESHANjengophawu lokhuseleko olongezelelweyo, i-encoder ibeka iliso ukujikeleza kwe-shaft. Ukuba ithe yabona ukuba akukho sindululo apho kufuneka kubekho isindululo, isistim iya kumisa umyalelo womjikelo, kwaye ibonise umboniso onempazamo othi 'AKUKHO NYUKUMBISO EFUMANIWE'. Ukulibaziseka okuvumelekileyo phambi kokuba esi siphoso siqatshelwe sisistim sinokuhlenga-hlengiswa ukusuka ku-0.2s ukuya ku-0.6s, kodwa akufuneki kutshintshwe kulungiselelo lwe-0.3 lweFactory Default ngaphandle kokuba kuyalelwe ukuba kwenziwe njalo ngabasebenzi benkxaso yobugcisa.
BALLANCE TSHEKINje ukuba ukhethwe kwimenyu, umnyango uya kuqhuba ngokuzenzekelayo ngomjikelo omnye ogcweleyo wokuvala/ovuliweyo (emva kokusetha kwakhona ikhowudi yekhowudi). Iya kuthi emva koko inike ingxelo kumaxabiso esikrini emele amandla afunekayo ukuvula nokuvala umnyango. Umahluko kula manani ubonisa ukungalingani, kwaye uhlengahlengiso kwixinzelelo lwentwasahlobo kufuneka lwenziwe ngokufanelekileyo. Sebenzisa eli nqaku kwakhona ukuze uqinisekise uhlengahlengiso olululo.
UKUPHINDISELA KWISETINGI SEFETRIOlu seto luvumela ukusetwa kwakhona kwazo zonke iinketho zemenu ukuya kumzi-mveliso ongagqibekanga ocetyisiweyo kwiminyango yecandelo. Ezi ziiSetingi zasefektri:

QALA IMENU
Isibali-xesha sokuvala: …………………………………………………….. CIMA
Umqulutage Uluhlu: ……………………………………………………. 208V-240V
Umiselo lweMida yamacango: ……………………………………………….. 4 Ujikelezo – Kufuneka luCwangciswe ngokutsha nguMhlohli.
Isantya sokuvula: …………………………………………………….. 3
Isantya sokuvala: ………………………………………………………. 3
IMENU YOSEKO ABANGAPHAMBILI
Ukubuyisela umva isibali-xesha: ……………………………………………… 1.0 Imizuzwana
PWM Frequency: …………………………………………… 12 kHz
I-Dynamic Brake: ……………………………………………… CIMA
Amandla okuvula: ………………………………………………. 10
Amandla okuvala: ………………………………………………………
Vula isantya esicothayo: …………………………………………… Siqhelekile
Vala isantya esicothayo: …………………………………………. Okuqhelekileyo
Vala Rampphantsi: ……………………………………… Okuzenzekelayo
Vula i-Rampphantsi: …………………………………. Ngokuzenzekelayo
Vula iiKhetho zoMda-Iqhosha lokucofa:………………………. Misela umda
Vula iiKhetho zoMda – iRadiyo ekude:…………………….. Seta umda
Ugqithiso lweziphumo:………………………………………. Inikwe amandla Xa Ivuliwe
Ukudanyaza okuBomvu: ……………………………………………………. CIMA
Advanced Red: ……………………………. CIMA
Ububomvu obukwinqanaba eliphezulu: …………………………………….. Vula/Vala
IShedyuli yoLondolozo: ……………………………….. 250,000 Imijikelo
Vula Ukutshintsha koMda: ……………………………………………. Hayi
Vala Ramp-Ixesha lokuphumla ……………………………………… 1.0 Imizuzwana
Ixesha lokubona iMotion……………………………………….. 0.3 Imizuzwana
Emva kokwenza ukusetwa kwakhona kwefektri (ukuba kubonwa kuyimfuneko), hlengahlengisa useto njengoko kufuneka, kwaye useto kwakhona useto lomda weprogram kwaye wenze ulungelelwaniso emva koko.
UKUPHUMA IMENU EPHAMBILI – UKHALISO NOVAVANYOUkuphuma kwi-ADVANCED MENU, cofa kwaye ukhulule iqhosha elithi STOP ngelixa i-ADVANCED MENU ivela kwiLCD. Oku kuya kukubuyisela kwi- STARTUP MENU. Cinezela kwaye ukhulule iqhosha elithi STOP kwakhona ukuphuma kuzo zonke iimenyu kunye nokuvavanya useto olutshintshileyo. Ukuba, ngelixa ubukwi-ADVANCED MENU kwaye ugcine utshintsho kwi-PWM Frequency, Vula Rampphantsi okanye Vala Rampphantsi uzakufunwa ukuba wenze ulungelelwaniso olukhawulezayo lwendlela. Iingcebiso zesikrini ziya kubonelela ngomyalelo wexesha lokwenyani kwiimfuno zolungelelwaniso. Jonga iPhepha lama-21 ngolwazi oluthe vetshe ngoLungiso.
Nje ukuba iCalibration igqitywe okanye ukuba bekungafuneki, isistim iya kuqhuba uxilongo olukhawulezayo, kwaye iLCD kufuneka ibonise ucango olukhoyo (Oluvuliweyo, luvaliwe okanye luyekwe). Kungoku apho uvavanyo lwalo naluphi na useto olutshintshiweyo lunokuqalisa.

UBUGQIBELO WEBHETRI EPHETHWE EMTHETHWENI – AMANDLA OUTAGE Operation

I-Pulse iyifektri ixhotyiswe ngenkqubo yokugcina ibhetri enelungelo elilodwa lomenzi kwaye isebenze ngokuzenzekelayo ngexesha lokuphuma kwamandla.tage. Olu gcino lwebhetri lusebenza nokuba kukho umonakalo webhodi owenzekayo ngenxa yamandla angaphandle afana nombane okanye impembelelo.
Ngexesha lamandla outage, tyhala kwaye ubambe iqhosha le-VULA ukuze uvule umnyango, kwaye ucofe kwaye ubambe iqhosha le-CLOSE ukuze uvale umnyango - umnyango uya kuphendula ngokufanelekileyo, kodwa qaphela ukuba izantya ziya kuncitshiswa.
Imida ayisebenzi, kwaye kubalulekile ukukhulula iqhosha ngokukhawuleza ukuba umnyango ufikelele kwindawo efanelekileyo.
Zonke izixhobo zokhuseleko ziya kukhutshazwa ngexesha lomsebenzi wokugcinwa kwebhetri kwaye nawuphi na umsebenzi osebenza emnyango kufuneka agcine umgca ocacileyo wokujonga kunye nomnyango ukuze kuncitshiswe umngcipheko wempembelelo enokwenzeka yomnyango kunye nabasebenzi okanye izixhobo, kunye nokuqinisekisa ukuba umnyango usebenza ngokukhuselekileyo. .
QAPHELA: XA USEBENZISA IBHETRI EYINGCACISO, UMDA AWUNJWA. KUFUNEKA UKHULULE IQHUBA KWI IXESHA ELIFANELEKILEYO, OKANYE UMNGCIPHEKO WOKUVUSELELA I-CIRCUIT BREAKER. SUKUBAMBA OKUVILEYO OKANYE UVALE IQHUSHA NAYIPHI NA OKUDE KUNOKUDINGEKA.
Ukuvumela/ukuvavanya usetyenziso lwenkxaso yebhetri xa amandla ekhona, cima umbane kumsebenzisi. Kwimeko apho iibhetri ziphelelwe ngokupheleleyo okanye zilahlekile, isiseko semoto sikwaxhotyiswe nge-3/8” yokungena kwiratchet. CIMA AMANDLA KWI-OPERATOR (nokuba umbane ubonakala uphumile), khusela i-crankshaft, i-socket wrench okanye i-drill yamandla nge-3/8 "intloko ye-ratchet (engabandakanyi) ngaphakathi kwendawo yokungena ye-ratchet kwaye uyijikelezise kwicala elifanelekileyo ukuze uvule. okanye uvale ucango. Layita umbane xa umsebenzi wezandla ungasafuneki.

QAPHELA NGEEBHETRI

Iibhetri ze-lead-acid ezibonelelweyo zi-2 x 12V eziqhagamshelwe kuthotho ukubonelela nge-24Vdc. Isilawuli sibonelela ngetshaja echuliweyo ejongweyo ukuze kugcinwe ubomi bebhetri. Ukuba iibhetri zikhutshiwe ngokupheleleyo kwaye azisamkeli intlawulo, nceda ubeke endaweni yazo iibhetri ezilinganayo, kwaye ulahle iiyunithi eziphelelwe lixesha ngokwemigaqo yendawo yendawo. UNGAZE ususe i-jumper enikiweyo phakathi kweebhetri ngaphandle kokuba ukwinkqubo yokutshintshwa, kwaye uqiniseke ukuba udibanisa kwakhona xa kufuneka ukutshintshwa kwebhetri.

IZICELO EZINGAMANGELI UMOYA

I-iControls icebisa uhlaziyo olukhoyo kuzo zonke izicelo zeMozulu ezixhathisayo. I-Standard Pulse Operator Motors ilinganiswe nge-IP44, kwaye ingaba sesichengeni sokungena kwamanzi. Ngapha koko, i-photo-eye sensors ebonakalisa i-photo-eye sensors inotyekelo lokuchatshazelwa kakubi kukuxinanisa kwisibonisi, ukuthintela ukusebenza okuthembekileyo kwiimeko ezinjalo.
I-iControls inikezela ngexabiso eliphantsi kwemozulu echasene nemozulu evala amanqaku angenayo kwibhokisi ye-motor junction, kwaye iquka i-NEMA 4X ye-thru-beam sensor endaweni ye-photo-eye. Nceda uqhagamshelane ne-iControls ngeenkcukacha kunye namaxabiso.

IZIQULATHO ZOKUSEBENZA KWE-PULSE

ISIKHOKELO SOKUDLULA INGXAKI

UPHAWU	UMBANGELA	ICEBISO SENZO
AKUKHO MBONISO KWIPHANSI YELCD	AKUKHO AMANDLA.	Ukukhangela amandla kuvuliwe kwi-circuit breaker, qhawula uqhagamshelwano, kwaye ukhangele imidibaniso yeentambo.
		Khangela i-fuse (jonga i-fuse specs kwimiyalelo yokufakela) kwibhokisi yesiphambuka.
	ULAHLEKO (IZI-).	Khangela imidibaniso kwi-J/bhokisi (kufuphi nomsebenzisi) kunye nephaneli yolawulo; khangela ukuba intambo yeribhoni ukuya kumboniso we-LCD idityaniswe ngokuqinileyo kuzo zombini iziphelo.
	UMQULUTAGUKULAHLA KWIINGCINGA PHAKATHI KWEBHOKISI YE-OPERATOR JUNCTION UKUZE ULAWULO.	Jonga ivoltage phakathi kwetheminali +24 kunye neCOM, ukuba akukho mandla okanye iPulse voltage ingaphantsi kwe 23V, khangela iingcingo phakathi kwebhokisi yeJunction (kufuphi nomsebenzisi) kunye nephaneli yokulawula.
	INDIBANO YEPHAneli ye-LCD.	Ukuba ibhaqiwe i-24Vdc kwaye intambo yeribhoni iqhagamshelwe ngoko ke ukudityaniswa kwepaneli ye-LCD kunokufuneka.
	IBHODI YOLAWULO YEPHANSI.	Nqamula + ucingo lwe-24V (ukusuka kwi-J / ibhokisi) kwiqela lolawulo, khangela i-voltage phakathi kocingo oluqhawulwe kunye netheminali ye-COM, ukuba voltagI-e yi-24Vdc ngoko ke ukutshintshwa kwebhodi yesekethe yolawulo kungafuneka.
UCANGO LUMISA NGOKUQHELEKILEYO (AWUQAPHELI IMIDA) INDAWO.	UMBA OWENZEKAYO	Qhagamshelana neNombolo yasimahla xa ufuna uncedo: 1-833-785-7332
UCANGO RHOQO LUMISA EMFUTSHANE KWIMO ESIVILEYO	UCANGO LUNOKUPHUMA OKUNGAKUHLANGANISIWE.	Qhuba iBalance Check kwi-Advanced Menu.
UCANGO UBUYA PHAMBI KOKUBA UFIKE KWINDAWO ESISONDELEKE NGAYO OKANYE KANYE NJENGOKUBA IQHOSHA LOKUVALA LIKHULULIWE.	I-PHOTO-EYE/REFLECTOR/ THRU-BEAM SENSOR AYIGCAWANGA NGENDLELA YOMTHETHO/ IVINWE/ AYIFANELEKILEYO.	Ukucoca, ukulungelelanisa kwakhona kunye / okanye ukuthintela okucacileyo phambi kweenzwa / i-reflector. Phinda ujonge iingcingo njengoko kubonisiwe kwiSazobe soku-1 kwiphepha le-13. Qinisekisa ukuba intambo okanye ukuhluthwa kwemozulu akubangeli siphazamiso.
	UKUBEKWA OKUNYANZELEKILEYO KUPHATHELELE KAKHULU	Lungisa uMnyanzelo wokuVala kwisetingi enganenovakalelo kwiMenu ePhezulu. Isi-1 sinobuntununtunu kakhulu, kwaye i-20 ayikhathali kangako.
	ICANDELO LESITHATHU UKUBUYISA IZIXHOBO EZINGASEBENZAYO.	Nqamula izixhobo zokubuyisela umva komntu wesithathu, faka i-jumper phakathi kokubuyisela umva i-terminal ye-3 kunye ne-+24 kwaye uvavanye kwakhona. Phinda uqhagamshele umva isixhobo esinye ngexesha ukwahlula isixhobo esonakeleyo, (jonga kwiphepha le-11-17 Kwincwadana yokufakela).
'UCANGO LUMISIWE' UMYALEZO KWI-LCD PANEL	UKUTHINJWA OKANYE UCANGO LUTHWEKILE NGENXA YOKUTHINJWA.	Susa isithintelo okanye ukhulule umnyango, qhawula (cima) amandla e-AC kwaye uvavanye ucango phantsi kwamandla ebhetri.
	I-PUSHER SPRINGS INOBA LUTHINTE UCANGO UKUNGAFIKI KWIMIDA EVULEKILEYO.	Susa iPusher Springs kwaye ufakele izibiyeli zomda ophezulu onikwe nomsebenzisi okanye usete ngokutsha OPEN umda ukuze iPusher Spring ingabandakanyekanga.
	UKUNGABIKHO KWE-ENCODER	Qhagamshelana neNombolo yasimahla xa ufuna uncedo: 1-833-785-7332
UCANGO UHAMBA I-I-Intshi EZIMBALWA EMVA UKUVULA/UKUVALA UMYALELO KUNYE NOKUMISA	I-JUMPER PHAKATHI KWE-'S' KUNYE NE-'+24' TERMINAL IYASUSWA.	Ukuba akukho sikhululo sokutyhala esifakwe intambo endaweni yaso, phinda ufake i-jumper.
	IQHUSHA LOKUDE AYINAYO I-NC (NGEQHELO IVALIWE) UQHAGAMSHELWANO NGEQHOSHA LOKUMISA.	Buyisela isikhululo seqhosha lokutyhala (okanye umfowunelwa weqhosha elithi STOP) kulowo unomfowunelwa weNC kwiqhosha elithi STOP.
	ISIKHULULO SOKUTYHALA IQHOSHA ELIDE ENENTSHWANE NGENGACHAPHAZANGA.	Jonga kwaye ulungise iingcingo zombane njengoko kuyimfuneko.
UCANGO ALUVALELI KWI-REMOTE OKANYE UKUVALA ISIXA	I-PUSHER SPRINGS INOKUTHINTE UCANGO UKUVULA NGOKUPHELELEYO KUMDA OVULEKILEYO (ISIKRINI SIFUNDWA 'UCANGO LUMISELWE') .	Susa imithombo ye-pusher kwaye ubeke endaweni yezibiyeli ezibonelelweyo zoMda; okanye uhlengahlengise Cwangcisa uMda oVulekileyo ukuze ungabandakanyeki kwimithombo ye-pusher kwaye usete zonke izixhobo zokuvula ukuvula umnyango wokuSeta uMda.
	ISIQINISEKISO SIVALE AYISEKELWE NGOKUFANELEKILEYO.	Seta kwakhona Vala isibali-xesha, (jonga kuPg 18 kwincwadi yofakelo).
	AKUKHO ISIXHOBO ESISEBENZAYO SOKUBUYISA KWI-R1 OKANYE I-R2 TERMINAL	Qinisekisa ukuba isixhobo esi-1 esifanelekileyo nesisebenzayo sifakwe ubuncinane kwenye yezi terminal. Ukuba ifakiwe, khangela i-wiring kunye nokulungelelaniswa kunye nokusebenza kovavanyo
UCANGO AYISEBENZE KUMANDLA EBHETRI	ICIRCUIT BREAKER IYAVUTHWA	Yenza kwakhona i-breaker circuit ngokucofa iqhosha lokuseta kwakhona.
	IBETHRI ZINOKUKHUPHA, OKANYE ZIFILE OKANYE IBHODI YOLAWULO ENESIFO.	Khangela iibhetri voltage, ukuba iphantsi mabahlawulise iiyure ezingama-24 ngombane we-AC ON. Zibuyisele iibhetri ukuba azikahlawuliswa. Buyisela ibhodi yokulawula ukuba iibhetri zitshajwe ngokupheleleyo kwaye nocango lulungelelene.
	UCANGO NGAPHANDLE KWE-BALANCE.	Qhuba iBalance Check kwi-Advanced Menu.
	AMANDLA ASESEKHONA.	Qinisekisa ukuba amandla aphambili kwiyunithi acinyiwe.
NGENZA UKUBEKWA ILISO- UKUQHUBEKA KUQHUBEKA	UMNYANGO WOKUVALA AWUBEKWA NGOKUFANELEKILEYO	Lungisa uMbutho wokuvala kunye/okanye wokuvula. Ulwalathiso luboniswe kumaphepha 21-22. Ukwandisa okanye ukunciphisa ngokusekelwe kubunzima bomnyango / icala kunye nokusetyenziswa kocango

I-PULSE UMSEBENZI UTSHINTSHO IZIQULATHO

UKUTSHINTSHWA KWECANDELO INKCAZELO	Pulse 500-100	Pulse 500-125	Pulse 750-100	Pulse 750-125	Ukubetha 1000
Imoto	PDC-500-1800	PDC-500-1800	PDC-750-1800	PDC-750-1800	I-PDC-P1000-1800
Iseti yebrashi yeMoto (2)	I-PDC-BRUSH	I-PDC-BRUSH	I-PDC-BRUSH	I-PDC-BRUSH	I-PDC-BRUSH
Ibhokisi yegiya	PDC-GB50/1/30	PDC-GB75/1.25/40	PDC-GB50/1/30	PDC-GB75/1.25/40	PDC-GB75/1.25/40
IBhodi yoLawulo ePhantsi	I-PCBA-PC7	I-PCBA-PC7	I-PCBA-PC7	I-PCBA-PC7	I-PCBA-PC7
Ibhodi ye-Upper Drive	PCBA-PD7	PCBA-PD7	PCBA-PD7	PCBA-PD7	PCBA-PD7
Ingalo yeTorque	I-PDC-TQA-50	I-PDC-TQA-75	I-PDC-TQA-50	I-PDC-TQA-75	I-PDC-TQA-75
I-Torque Arm Bracket	PDC-TQB-50	PDC-TQB-75	PDC-TQB-50	PDC-TQB-75	PDC-TQB-75
Izibiyeli zoMda w/ Hardware	PDC-LMTBKT	PDC-LMTBKT	PDC-LMTBKT	PDC-LMTBKT	PDC-LMTBKT
Ikhola kaShaff	I-PDC-COL-1.0	I-PDC-COL-1.25	I-PDC-COL-1.0	I-PDC-COL-1.25	I-PDC-COL-1.25
Isitshixo sikaShaff	I-PDC-KEY-3	I-PDC-KEY-3	I-PDC-KEY-3	I-PDC-KEY-3	I-PDC-KEY-3
Isifaki khowudi	PDC-ENCD50	PDC-ENCD75	PDC-ENCD50	PDC-ENCD75	PDC-ENCD75
Ibhetri (iqhekeza elinye)	PCB-BAT-5A	PCB-BAT-5A	PCB-BAT-7A	PCB-BAT-7A	PCB-BAT-9A
Iseti yebhetri	PCB-BAT-5A2	PCB-BAT-5A2	PCB-BAT-7A2	PCB-BAT-7A2	PCB-BAT-9A2
Iseti yamehlo eReflectorive	RPE-100SET	RPE-100SET	RPE-100SET	RPE-100SET	RPE-1000SET
ISensom yeFoto-yeliso Kuphela	I-RPE-100	I-RPE-100	I-RPE-100	I-RPE-100	I-RPE-100
Ifoto-Isibiyeli samehlo	I-RPESTB-BRKT	I-RPESTB-BRKT	I-RPESTB-BRKT	I-RPESTB-BRKT	I-RPESTB-BRKT
Ifoto-Eye Reflector	RPE-RFLC	RPE-RFLC	RPE-RFLC	RPE-RFLC	RPE-RFLC1000
Iphaneli yoLawulo ebiyelweyo	PCBA/ENC-	PCBA/ENC-	PCBA/ENC-	PCBA/ENC-	PCBA/ENC-
(Gqibile)	PC7/500	PC7/500	PC7/750	PC7/750	PC7/1000
Iphaneli yokulawula (akukho bhodi)	PCB-ENC-500	PCB-ENC-500	PCB-ENC-750	PCB-ENC-750	PCB-ENC-750
Intambo yeRibhoni	PCB-RIBCAB-1	PCB-RIBCAB-2	PCB-RIBCAB-1	PCB-RIBCAB-2	PCB-RIBCAB-2
Cofa iqhosha	PCB-PB1	PCB-PB1	PCB-PB1	PCB-PB1	PCB-PB1

IRemote Radio Transmitter/Receiver Wiring Diagram/ImiyaleloI-Wiring Receiver ukuya kwi-Pulse Operator:
Isitishi esinye:
Ukuba usebenzisa iqhosha elinye kuphela kwi-transmitter ukuze usebenze ucango, ucingo ngokomzobo osekhohlo ngasentla kwiitheminali zokuLawula i-REMOTE kwiBhodi yoLawulo lwePulse Operator. Nje ukuba ifakelwe kwaye idityaniswe kakuhle nesidluliseli (jonga icala elichaseneyo malunga nemiyalelo yokukhwelana), iqhosha elicwangcisiweyo liya kuvula okanye livale ucango, ngokuxhomekeke kwindawo yocango. Ukuba isibali-xesha esibuya umva sisebenza kwiPulse Operator yakho, iqhosha elicwangcisiweyo liya kuvula ucango kuphela. Qaphela ukuba onke amaqhosha ama-3 kwisidluliseli anokucwangciswa ukuba asebenze kucango olunye, okanye acwangciswe ngokwahlukeneyo ukuba abamkeli abahlukeneyo basebenzise iingcango ezi-3 ezahlukeneyo.
Isitishi esiMabini:
Ukuba usebenzisa iqhosha elinye kwisidluliseli ukuvula kunye nelinye ukuvala ucango, ucingo ngokomzobo wasekunene ngasentla kwiitheminali ze-PUSH BUTTON STATION kwiBhodi yoLawulo lwePulse Operator. Nje ukuba ifakwe ngokuchanekileyo kwaye idityaniswe nesidluliseli (jonga icala elichaseneyo ngemiyalelo yokudibanisa), iqhosha ngalinye elicwangcisiweyo liya kwenza umsebenzi walo owabelweyo.
I-Remote Radio Transmitter/Receiver pairing Imiyalelo Ukukhwelana i-RXTA-100 Isamkeli kwi-TXTA-100 Transmitter
Qhubeka kuphela ukuba umamkeli ufakwe iintambo ngokufanelekileyo kwaye amandla avuliwe.
Isitishi esinye:

1. Cofa iqhosha elithi 'leam' ecaleni kophawu lwe-S1 kumamkeli de i-L1 LED ehambelanayo ivuleke. Sukucinezela/udwelise iqhosha le-S2 kusetyenziso lwesitishi esinye.
2. Cinezela kwaye ubambe iqhosha elifunekayo kwisidluliseli de i-L1 LED idanyaze amaxesha ama-4 ukubonisa impumelelo yokubhanqa. Khupha iqhosha.
3. Cinezela iqhosha elicwangcisiweyo kwisidluliseli sokuqinisekisa-i-L1 LED kufuneka ikhanyise.
4. Phinda eli nyathelo ngawo onke amaqhosha kwi-transmitter (ukubhanqa nge-S1), ukuba isetyenziselwa lo mamkeli kuphela.

Isitishi esiMabini:

1. Cinezela iqhosha elithi 'funda' ecaleni kophawu lwe-S1 kumamkeli de kuvulwe i-L1 LED ehambelanayo.
2. Cofa kwaye ubambe iqhosha elithi 'VULA' elifunekayo kwisidlulisi de i-L1 LED idanyaze amaxesha ama-4 ukubonisa. impumelelo yokudibanisa. Khupha iqhosha.
3. Cinezela iqhosha elicwangcisiweyo kwisidluliseli sokuqinisekisa-i-L1 LED kufuneka ikhanyise.
4. Cinezela iqhosha elithi 'ukufunda' ecaleni kophawu lwe-S2 kumamkeli de kuvulwe i-L2 LED ehambelanayo.
5. Cinezela kwaye ubambe iqhosha 'CLOSE' elifunekayo kwisidlulisi de i-L2 LED idanyaze amaxesha ama-4 ukubonisa impumelelo yokubhanqa. Khupha iqhosha.
6. Cinezela iqhosha elicwangcisiweyo kwisidluliseli sokuqinisekisa-i-L2 LED kufuneka ikhanyise.

I-PULSE 500+ WARANTY

Ukhuseleko
I-Pulse 500-1000 Abaqhubi baqinisekisiwe ngokupheleleyo ixesha le-2 iminyaka okanye i-1,000,000 imijikelo (nayiphi na into eza kuqala) ukususela ngomhla wokuthenga kwabo. Esi siqinisekiso sibandakanya, kwaye silinganisiwe, kulo lonke icandelo kunye neziphene zokwenziwa kwemveliso kuphela, kwaye asibandakanyi ukusilela okunokwenzeka ngenxa yamandla angaphandle kubandakanywa izitenxo ezibangelwa yimpembelelo, ufakelo olungafanelekanga kunye/okanye uqhagamshelo, umthamo.tagUkunyuka kunye nabo bonke abanye abasebenzisi kunye/okanye ukusilela okubangelwe kokusingqongileyo. Esi siqinisekiso sivumelekile ukutshintshwa okanye ukulungiswa kwemveliso enesiphene kuphela, kwaye ayibandakanyi nawuphi na umsebenzi owenziweyo wokususwa okanye ukufakwa kwecandelo elineziphene, ukufakwa kwakhona kwemveliso yokutshintshwa / elungisiweyo, iindleko zokuthumela ngenqanawa yokubuyisela imveliso, okanye ezinye iindleko ezinokwenzeka ezinxulumene nokungasebenzi komsebenzisi.I-Coverage ayinwebeki ekugcinweni kweMoto Brushes ekufuneka itshintshwe yonke imijikelo engama-200,000. Ukuthembeka kweSoftware kunye nokusebenza kubandakanywa phantsi kwewaranti yethu, kodwa ayibandakanyi uhlaziyo lwesoftware, uphuculo kunye/okanye uhlengahlengiso ngaphandle kokuba kugunyaziswe ngokubhaliweyo yi-iControls.
Amabango
Ngaphambi kokuba wenze ibango lewaranti, nceda ufowunele iPulse Tech Support ku-1-833-785-7332 kwaye ucele uncedo lokusombulula ingxaki. SUKUSUSA IMVELISO , de ugunyaziswe.
Phawula
Ngesicelo, i-iControls inokubonelela ngoncedo lwentsimi (imali eyongezelelweyo ingasebenza) kunye / okanye iingcebiso ngokufakela, ukulungisa iingxaki, ukuphucula imveliso okanye ukuphuculwa kwemveliso yethu. Ngaphantsi kwemimiselo yesi siqinisekiso esilinganiselweyo, kuwo nawaphi na amacandelo omqhubi afunyanwe enesiphene xa ehlolwa ngabasebenzi abagunyazisiweyo be-iControls, i-iControls iya kuthatha indawo/ilungise amacandelo angasebenziyo anesiphene. Iintlawulo zabasebenzi zofakelo okanye ukulungiswa ziya kuba luxanduva lomthengi kwaye kufuneka zenziwe ngumthengisi ogunyazisiweyo we-iControls apho kukho khona. Esi siqinisekiso sisebenza kuphela kubaqhubi abafakwe ngobuchule ngumthengisi we-iControls ogunyazisiweyo kwaye oko kwenziwe ngaphakathi kwezikhokelo zencwadana yokufakela. Kwimeko apho enye imodeli yomsebenzisi okanye inxalenye iyeka okanye iphelelwe lixesha, iControls inelungelo lokutshintsha imveliso ngenye indlela efanelekileyo.
Ii-iControls aziyi kuba noxanduva lwawo nawuphi na umonakalo obangelwayo okanye onokwenzeka. Zonke ezinye iziqinisekiso, ezichaziweyo okanye ezichaziweyo, kubandakanywa nasiphi na iwaranti yokuthengiselana, azibandakanywanga ngokucacileyo. Eminye imimandla yolawulo ayikuvumeli ukukhutshelwa ecaleni okanye uthintelo lomonakalo obangelwayo okanye ongalindelekanga, ngoko ke uthintelo okanye ukukhutshwa kungasentla akunakusebenza kuwe. Esi siqinisekiso sikunika amalungelo athile asemthethweni, kwaye usenokuba namanye amalungelo awohlukayo ukusuka kulawulo ukuya kulawulo. Ukwenza ibango phantsi kwezi ziqinisekiso,
qhagamshelana ne-iControls.
Ngolwazi oluthe vetshe, nceda uqhagamshelane www.devancocanada.com okanye ufowunele umnxeba simahla ngo-1-855-931-3334

Amaxwebhu / Izibonelelo

Ulawula iPulse Series Controller Pulse Red [pdf] Incwadi yoMnini Pulse Series Controller Pulse Red, Pulse Series, Controller Pulse Red, Pulse Red, Red

Iimbekiselo

• Incwadi yokusebenzisa