Boardcon Embedded CM1126B-P System on Module
Iinkcukacha
| Uphawu | Iinkcukacha |
| ICPU | I-Quad-core Cortex-A53 |
| DDR | 2GB LPDDR4 (ukuya kuthi ga kwi-4GB) |
| eMMC FLASH | I-8GB (ukuya kuthi ga kwi-256GB) |
| Amandla | I-DC 3.3V |
| I-MIPI DSI | 4-Indlela |
| I2S | I-4-CH |
| I-MIPI CSI | 2-CH 4-Lane |
| RGB LCD | 24 bit |
| Ikhamera | I-1-CH(DVP) kunye ne-2-CH(CSI) |
| i-USB | 2-CH (USB HOST 2.0 and OTG 2.0) |
| I-Ethernet | 1000M GMAC |
| SDMMC | I-2-CH |
| I2C | I-5-CH |
| SPI | I-2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| PWM | I-11-CH |
| ADC IN | I-4-CH |
| Ubungakanani beBhodi | 34 x 35mm |
Intshayelelo
Malunga nale ncwadana
Le ncwadana yenzelwe ukunika umsebenzisi i-overview of the board and its benefits, complete feature specifications, and setup procedures. It contains important safety information as well.
Ingxelo kunye noHlaziyo kule Manuwali
Ukunceda abathengi bethu benze uninzi lweemveliso zethu, sithe gqolo ukwenza izixhobo ezongezelelweyo nezihlaziyiweyo zifumaneke kwi-Boardcon webindawo (www.boardcon.com, www.armdesigner.com). Ezi ziquka iimanyuwali, amanqaku isicelo, inkqubo examples, kunye nesoftware ehlaziyiweyo kunye nehardware. Ngena ngamaxesha ukuze ubone ukuba yintoni entsha! Xa sibeka phambili umsebenzi kwezi zixhobo zihlaziyiweyo, impendulo evela kubathengi yeyona mpembelelo yokuqala, Ukuba unemibuzo, izimvo, okanye iinkxalabo malunga nemveliso okanye iprojekthi yakho, nceda ungathandabuzi ukunxibelelana nathi support@armdesigner.com.
CM1126B-P Introduction
Isishwankathelo
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltage must operate at a 3.3V logic level.
Iimbonakalo
Microprocessor
- I-Quad-core Cortex-A53 ukuya kuthi ga kwi-1.6GHz
- 32KB I-cache kunye 32KB D-cache kumbindi ngamnye, 512KB L3 cache
- Iyunithi yeNkqubo yeNeural e-3.0
- RISC-V MCU to support 250ms fast boot
- Ubukhulu be-12M ISP
Umbutho weMemori
- I-LPDDR4 RAM ukuya kuthi ga kwi-4GB
- eMMC ukuya kuthi ga kwi-256GB
- SPI Flash ukuya kuthi ga kwi-8MB
Idikhowuda yevidiyo/Iencoder
- Ixhasa ikhowudi yevidiyo/ikhowudi ukuya kuthi ga kwi-4K@30fps
- Ixhasa i-real-time decoding ye-H.264/265
- Ixhasa i-real-time UHD H.264/265 i-encoding yevidiyo
- Ubungakanani bomfanekiso ukuya kuthi ga kwi-8192 × 8192
Bonisa Inkqubo engaphantsi
- Imveliso yevidiyo
- Supports 4 lanes MIPI DSI up to 2560×1440@60fps
- Supports 24-bit RGB parallel output
- Umfanekiso ngaphakathi
- Supports up to 16-bit DVP interface
- Ixhasa i-2ch MIPI CSI 4lanes interface
I2S/PCM/AC97
- I-interface ye-I2S/PCM emithathu
- Ukuxhasa uluhlu lweMic Ukuya kuthi ga kwi-8ch PDM/TDM ujongano
- Inkxaso PWM imveliso yomsindo
I-USB kunye nePCIE
- Imidibaniso emibini ye-USB ye-2.0
- One USB 2.0 OTG and one 2.0 USB host
I-Ethernet
- RTL8211F kwibhodi
- Inkxaso 10/100/1000M
I2C
- Ukuya kuthi ga kwi-I2Cs ezintlanu
- Imowudi yenkxaso eqhelekileyo kunye nemowudi ekhawulezayo (ukuya kuthi ga kwi-400kbit/s)
I-SDIO
- Inkxaso ye-2CH SDIO 3.0 protocol
SPI
- Ukuya kuthi ga kubalawuli beSPI ababini,
- Ujongano olulandelelanayo olupheleleyo lwe-duplex
UART
- Inkxaso ukuya kuthi ga kwi-6 UARTs
- I-UART2 eneengcingo ezi-2 zezixhobo zokucoca
- Embedded two 664-byte FIFOs
- Inkxaso yemowudi yokulawula ukuhamba kwe-auto ye-UART0/1/3/4/5
ADC
- Ukuya kuthi ga kwiitshaneli ezine ze-ADC
- Isisombululo se-12-bit
- Umqulutage igalelo uluhlu phakathi 0V ukuba 1.8V
- Inkxaso ukuya kuthi ga kwi-1MS/ssampulwimi
PWM
- Ii-PWM ezili-11 ezikwi-chip ezinomsebenzi wokuphazamiseka
- Support 32-bit time/counter facility
- Inketho ye-IR kwi-PWM3/7
Iyunithi yamandla
- Amandla aDiscrete ebhodini
- Igalelo elinye le-3.3V
CM1126B-P Block Diagram
RV1126B-P Block Diagram
Ibhodi yophuhliso (Idea1126) Block Diagram
CM1126B-P PCB Dimension
CM1126B-P Pin Definition
| Iphini | Umqondiso | Inkcazo okanye imisebenzi | GPIO uthotho | IO Voltage |
| 1 | I-LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | I-LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | GPIO2_D0_d | 3.3V |
| 3 | I-LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | GPIO2_D1_d | 3.3V |
| 4 | I-LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | GPIO2_D2_d | 3.3V |
| 5 | I-LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | GPIO2_D3_d | 3.3V |
| 6 | GND | Umhlaba | 0V | |
| 7 | GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | WIFI_REG_ON | SPI0_MOSI_M0 | GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | GPIO0_A7_d | 3.3V(V2) |
| 11 | WIFI_WAKE_HOST | SPI0_CLK_M0 | GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Eyokulungisa ingxaki | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Eyokulungisa ingxaki | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
GPIO3_D5_d | 3.3V |
| Iphini | Umqondiso | Inkcazo okanye imisebenzi | GPIO uthotho | IO Voltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Umhlaba | 0V | |
| 32 | OTG_DP | Can be used for download | 1.8V | |
| 33 | OTG_DM | Can be used for download | 1.8V | |
| 34 | OTG_DET(V2) | OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | Igalelo le-3.3V eliPhambili laMandla | 3.3V | |
| 38 | VCC3V3_SYS | Igalelo le-3.3V eliPhambili laMandla | 3.3V | |
| 39 | USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Kufuneka isetyenziswe kwi-SD Card | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | Imveliso yewotshi ye-RTC | GPIO0_A2_u | 3.3V(V2) |
| 42 | nRESET | Lungisa igalelo leqhosha | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V |
| Iphini | Umqondiso | Inkcazo okanye imisebenzi | GPIO uthotho | IO Voltage |
| 52 | MIPI_CSI_RX0_D0
N |
Igalelo le-MIPI CSI0 okanye iLVDS0 | 1.8V | |
| 53 | GND | Umhlaba | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
Igalelo le-MIPI CSI1 okanye iLVDS1 | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Umhlaba | 0V | |
| 71 | LED1/CFG_LDO0 | I-Ethernet LINK ye-LED | 3.3V | |
| 72 | LED2/CFG_LDO1 | I-Ethernet SPEED LED | 3.3V | |
| 73 | MDI0+ | Isiginali ye-Ethernet MDI | 1.8V | |
| 74 | MDI0- | Isiginali ye-Ethernet MDI | 1.8V | |
| 75 | MDI1+ | Isiginali ye-Ethernet MDI | 1.8V | |
| 76 | MDI1- | Isiginali ye-Ethernet MDI | 1.8V | |
| 77 | MDI2+ | Isiginali ye-Ethernet MDI | 1.8V | |
| 78 | MDI2- | Isiginali ye-Ethernet MDI | 1.8V | |
| 79 | MDI3+ | Isiginali ye-Ethernet MDI | 1.8V | |
| 80 | MDI3- | Isiginali ye-Ethernet MDI | 1.8V | |
| 81 | I2C1_SCL | UART4_CTSn_M2 | GPIO1_D3_u | 1.8V |
| Iphini | Umqondiso | Inkcazo okanye imisebenzi | GPIO uthotho | IO Voltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | GPIO2_A3_d | 1.8V |
| 90 | GND | Umhlaba | 0V | |
| 91 | I-LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | GPIO2_A4_d | 3.3V |
| 92 | I-LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | GPIO2_A5_d | 3.3V |
| 93 | I-LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | GPIO2_A6_d | 3.3V |
| 94 | I-LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | GPIO2_A7_d | 3.3V |
| 95 | I-LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | GPIO2_B0_d | 3.3V |
| 96 | I-LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | GPIO2_B1_d | 3.3V |
| 97 | I-LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
GPIO2_B2_d | 3.3V |
| 98 | I-LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | I-LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
GPIO2_D7_d | 3.3V |
| 102 | I-LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | Igalelo le-ADC | 1.8V | |
| 114 | ADCIN2 | Igalelo le-ADC | 1.8V | |
| 115 | ADCIN1 | Igalelo le-ADC | 1.8V | |
| 116 | ADKEY_IN0 | Indlela yokubuyisela iseti (10K PU) | 1.8V | |
| 117 | GND | Umhlaba | 0V | |
| 118 | I-SDIO_CLK | GPIO1_B2_d | 3.3V(V2) | |
| 119 | I-SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Iphini | Umqondiso | Inkcazo okanye imisebenzi | GPIO uthotho | IO Voltage |
| 120 | I-SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | I-SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | I-SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | I-SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | I-LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | I-LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | I-LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | I-LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | I-LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | GPIO2_D4_d | 3.3V |
| 137 | I-LCDC_D10_3V3 | CIF_D6_M1 | GPIO2_B6_d | 3.3V |
| 138 | I-LCDC_D9_3V3 | CIF_D5_M1 | GPIO2_B5_d | 3.3V |
| 139 | I-LCDC_D8_3V3 | CIF_D4_M1 | GPIO2_B4_d | 3.3V |
| 140 | I-LCDC_D11_3V3 | CIF_D7_M1 | GPIO2_B7_d | 3.3V |
| 141 | I-LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | GPIO2_D5_d | 3.3V |
| 142 | I-LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | I-LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | I-LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Phawula:
1. Uninzi lwe-GPIO voltage yi 1.8V, kodwa ezinye izikhonkwane ziphawulwe 3.3V. 2. GPIO voltage change to 3.3V for marked (V2). |
||||
Ikhithi yoPhuhliso (Idea1126)
Isikhokelo soYilo lweHardware
I-Peripheral Circuit Reference
ISekethe yaMandla aPhambili
Debug Circuit
USB OTG Interface Circuit
PCB Footprint
Iimpawu zoMbane zeMveliso
Ukuchithwa kunye noBushushu
| Uphawu | Ipharamitha | Min | Chwetheza | Max | Iyunithi |
| VCC3V3_SYS | Inkqubo IO
Umqulutage |
3.3-5% | 3.3 | 3.3 + 5% | V |
| Iyss_in | VCC3V3_SYS igalelo langoku | 850 | mA | ||
| Ta | Ubushushu bokusebenza | -20 | 70 | °C | |
| Tstg | Ubushushu boGcino | -40 | 85 | °C |
Ukuthembeka koVavanyo
| Uvavanyo lokuSebenza lobushushu obuphezulu | ||
| Imixholo | Operating 8h in high temperatures | 55°C±2°C |
| Isiphumo | I-TBD |
| Operating Life Test | ||
| Imixholo | Operating in the room | 120h |
| Isiphumo | I-TBD |
Iwaranti enyiniweyo
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.
Ii-FAQs
Q: How do I upgrade the DDR memory on CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.
Q: What is the power supply requirement for CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.
Q: Can I expand the storage capacity of eMMC on CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.
Amaxwebhu / Izibonelelo
 |
Boardcon Embedded CM1126B-P System on Module [pdf] Incwadi yokusebenzisa V2.20250422, CM1126B-P System on Module, CM1126B-P, System on Module, Module |